ARM: dts: imx6qdl-gw5904: add internal mdio nodes
Subsystems (5)
PATCH 1/2 ARM: dts: imx6qdl-gw5904: add internal mdio nodes
Complete the switch definition by adding the internal mdio nodes.
--- arch/arm/boot/dts/imx6qdl-gw5904.dtsi | 35 +++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
arch/arm/boot/dts/imx6qdl-gw5904.dtsi +35 -0
@@ -212,6 +212,27 @@ switch@0 { compatible = "marvell,mv88e6085"; reg = <0>; + mdio { + #address-cells = <1>; + #size-cells = <0>; + + sw_phy0: ethernet-phy@0 { + reg = <0x0>; + }; + + sw_phy1: ethernet-phy@1 { + reg = <0x1>; + }; + + sw_phy2: ethernet-phy@2 { + reg = <0x2>; + }; + + sw_phy3: ethernet-phy@3 { + reg = <0x3>; + }; + }; + ports { #address-cells = <1>; #size-cells = <0>;
@@ -219,27 +240,41 @@ ports { port@0 { reg = <0>; label = "lan4"; + phy-handle = <&sw_phy0>; + phy-mode = "internal"; }; port@1 { reg = <1>; label = "lan3"; + phy-handle = <&sw_phy1>; + phy-mode = "internal"; }; port@2 { reg = <2>; label = "lan2"; + phy-handle = <&sw_phy2>; + phy-mode = "internal"; }; port@3 { reg = <3>; label = "lan1"; + phy-handle = <&sw_phy3>; + phy-mode = "internal"; }; port@5 { reg = <5>; label = "cpu"; ethernet = <&fec>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; }; }; };
Signature · 1 line
2.25.1
PATCH 2/2 ARM: dts: imx6qdl-gw5904: add dt props for populating eth MAC addrs
Add device-tree props to allow boot firmware to populate MAC addresses.
--- arch/arm/boot/dts/imx6qdl-gw5904.dtsi | 17 +++++++++++++---- 1 file changed, 13 insertions(+), 4 deletions(-)
arch/arm/boot/dts/imx6qdl-gw5904.dtsi +13 -4
@@ -52,6 +52,11 @@ / { /* these are used by bootloader for disabling nodes */ aliases { + ethernet0 = &fec; + ethernet1 = &lan1; + ethernet2 = &lan2; + ethernet3 = &lan3; + ethernet4 = &lan4; led0 = &led0; led1 = &led1; led2 = &led2;
@@ -237,32 +242,36 @@ ports { #address-cells = <1>; #size-cells = <0>; - port@0 { + lan4: port@0 { reg = <0>; label = "lan4"; phy-handle = <&sw_phy0>; phy-mode = "internal"; + local-mac-address = [00 00 00 00 00 00]; }; - port@1 { + lan3: port@1 { reg = <1>; label = "lan3"; phy-handle = <&sw_phy1>; phy-mode = "internal"; + local-mac-address = [00 00 00 00 00 00]; }; - port@2 { + lan2: port@2 { reg = <2>; label = "lan2"; phy-handle = <&sw_phy2>; phy-mode = "internal"; + local-mac-address = [00 00 00 00 00 00]; }; - port@3 { + lan1: port@3 { reg = <3>; label = "lan1"; phy-handle = <&sw_phy3>; phy-mode = "internal"; + local-mac-address = [00 00 00 00 00 00]; }; port@5 {
Signature · 1 line
2.25.1
Re: [PATCH 2/2] ARM: dts: imx6qdl-gw5904: add dt props for populating eth MAC addrs
Hi Tim,
Quoted 4 lines · Tim Harvey
Add device-tree props to allow boot firmware to populate MAC addresses.
Signed-off-by Tim Harvey <[email protected]>
Fabio Estevam
reviewerHi Tim,
[Adding Andrew]
Quoted 86 lines · Tim Harvey
Complete the switch definition by adding the internal mdio nodes.
Signed-off-by Tim Harvey <[email protected]>--- arch/arm/boot/dts/imx6qdl-gw5904.dtsi | 35 +++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)arch/arm/boot/dts/imx6qdl-gw5904.dtsi +35
-1@@ -212,6 +212,27 @@ switch@0 { compatible = "marvell,mv88e6085"; reg = <0>; + mdio { + #address-cells = <1>; + #size-cells = <0>; + + sw_phy0: ethernet-phy@0 { + reg = <0x0>; + }; + + sw_phy1: ethernet-phy@1 { + reg = <0x1>; + }; + + sw_phy2: ethernet-phy@2 { + reg = <0x2>; + }; + + sw_phy3: ethernet-phy@3 { + reg = <0x3>; + }; + }; + ports { #address-cells = <1>; #size-cells = <0>;@@ -219,27 +240,41 @@ ports { port@0 { reg = <0>; label = "lan4"; + phy-handle = <&sw_phy0>; + phy-mode = "internal"; }; port@1 { reg = <1>; label = "lan3"; + phy-handle = <&sw_phy1>; + phy-mode = "internal"; }; port@2 { reg = <2>; label = "lan2"; + phy-handle = <&sw_phy2>; + phy-mode = "internal"; }; port@3 { reg = <3>; label = "lan1"; + phy-handle = <&sw_phy3>; + phy-mode = "internal"; }; port@5 { reg = <5>; label = "cpu"; ethernet = <&fec>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; }; }; }; --2.25.1
Andrew Lunn
maintainerQuoted 3 lines · Fabio Estevam
Hi Tim,
[Adding Andrew]
It is not wrong, but it should also mostly not be needed. The switch driver can link internal PHYs to ports.
Quoted 11 lines
arch/arm/boot/dts/imx6qdl-gw5904.dtsi ports { · line 278
Quoted 11 lines
port@5 { reg = <5>; label = "cpu"; ethernet = <&fec>;arch/arm/boot/dts/imx6qdl-gw5904.dtsi +6
-0+ phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; };
This part is needed to make a warning go away. Does the SoC network interface have phy-mode = "rgmii"; ?
Andrew
Quoted 8 lines · Andrew Lunn
Quoted 3 lines · Fabio Estevam
Hi Tim,
[Adding Andrew]
It is not wrong, but it should also mostly not be needed. The switch driver can link internal PHYs to ports.
Andrew,
I should have mentioned in the commit log that this does not change behavior on Linux but is required for boot firmware. Specifically U-Boot requires the internal PHY ports to be defined for its DSA architecture and they share dt's as much as possible.
Quoted 13 lines
Quoted 12 lines
arch/arm/boot/dts/imx6qdl-gw5904.dtsi ports { · line 278
Quoted 12 lines
port@5 { reg = <5>; label = "cpu"; ethernet = <&fec>;arch/arm/boot/dts/imx6qdl-gw5904.dtsi +6
-0+ phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; };
Quoted 2 lines
This part is needed to make a warning go away. Does the SoC network interface have phy-mode = "rgmii"; ?
No, it looks like this:
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
status = "okay";
fixed-link {
speed = <1000>;
full-duplex;
};
mdio {
#address-cells = <1>;
#size-cells = <0>;
switch@0 {
compatible = "marvell,mv88e6085";
reg = <0>;...
Is something here wrong?
Best Regards,
Tim
Andrew Lunn
maintainerQuoted 15 lines
Quoted 12 lines
Quoted 11 lines
arch/arm/boot/dts/imx6qdl-gw5904.dtsi ports { · line 278
Quoted 11 lines
port@5 { reg = <5>; label = "cpu"; ethernet = <&fec>;arch/arm/boot/dts/imx6qdl-gw5904.dtsi +6
-0+ phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; };Quoted 2 lines
This part is needed to make a warning go away. Does the SoC network interface have phy-mode = "rgmii"; ?
Quoted 8 lines
No, it looks like this:
&fec { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet>; phy-mode = "rgmii-id";Is something here wrong?
It suggests both ends should insert RGMII delays. So you will end up with double delays. Have one end say plain "rgmii" and the other "rgmii-id". I would probably go with the FEC being "rgmii".
Andrew
Quoted 23 lines · Andrew Lunn
Quoted 22 lines
Quoted 13 lines
Quoted 12 lines
arch/arm/boot/dts/imx6qdl-gw5904.dtsi ports { · line 278
Quoted 12 lines
port@5 { reg = <5>; label = "cpu"; ethernet = <&fec>;arch/arm/boot/dts/imx6qdl-gw5904.dtsi +6
-0+ phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; };Quoted 2 lines
This part is needed to make a warning go away. Does the SoC network interface have phy-mode = "rgmii"; ?
No, it looks like this:
&fec { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet>; phy-mode = "rgmii-id";
Quoted 7 lines
Quoted 1 line
Is something here wrong?
It suggests both ends should insert RGMII delays. So you will end up with double delays. Have one end say plain "rgmii" and the other "rgmii-id". I would probably go with the FEC being "rgmii".
Andrew
Andrew,
That makes sense - I will change the fec node to rgmii.
Upon further testing I find there is something else wrong with this patch however that I don't yet understand.
Without it the switch works fine (due to RGMII delay being configured via boot firmware) but I do get the warning you had mentioned due to the phy-mode/phy-handle props missing:
mv88e6085 2188000.ethernet-1:00: switch 0x1760 detected: Marvell 88E6176, revision 1
mv88e6085 2188000.ethernet-1:00: OF node /soc/bus@2100000/ethernet@2188000/mdio/switch@0/ports/port@5 of CPU port 5 lacks the required "phy-mode" property
mv88e6085 2188000.ethernet-1:00: OF node /soc/bus@2100000/ethernet@2188000/mdio/switch@0/ports/port@5 of CPU port 5 lacks the required "phy-handle", "fixed-link" or "managed" properties
mv88e6085 2188000.ethernet-1:00: Skipping phylink registration for CPU port 5 mv88e6085 2188000.ethernet-1:00 lan4 (uninitialized): PHY [mv88e6xxx-1:00] driver [Generic PHY] (irq=POLL)
mv88e6085 2188000.ethernet-1:00 lan3 (uninitialized): PHY [mv88e6xxx-1:01] driver [Generic PHY] (irq=POLL)
mv88e6085 2188000.ethernet-1:00 lan2 (uninitialized): PHY [mv88e6xxx-1:02] driver [Generic PHY] (irq=POLL)
mv88e6085 2188000.ethernet-1:00 lan1 (uninitialized): PHY [mv88e6xxx-1:03] driver [Generic PHY] (irq=POLL)
When I add the phy-mode/phy-handle props with this patch I get the following failure:
mv88e6085 2188000.ethernet-1:00: switch 0x1760 detected: Marvell 88E6176, revision 1
mv88e6085 2188000.ethernet-1:00: switch 0x1760 detected: Marvell 88E6176, revision 1
mv88e6085 2188000.ethernet-1:00: configuring for fixed/rgmii-id link mode mv88e6085 2188000.ethernet-1:00: p5: delay RXCLK yes, TXCLK yes mv88e6085 2188000.ethernet-1:00: p5: delay RXCLK yes, TXCLK yes mv88e6085 2188000.ethernet-1:00: Link is Up - 1Gbps/Full - flow control off mv88e6085 2188000.ethernet-1:00 lan4 (uninitialized): validation of internal with support 00000000,00000000,000062ff and advertisement 00000000,00000000,000062ff failed: -EINVAL
mv88e6085 2188000.ethernet-1:00 lan4 (uninitialized): failed to connect to PHY: -EINVAL
mv88e6085 2188000.ethernet-1:00 lan4 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 0
mv88e6085 2188000.ethernet-1:00 lan3 (uninitialized): validation of internal with support 00000000,00000000,000062ff and advertisement 00000000,00000000,000062ff failed: -EINVAL
mv88e6085 2188000.ethernet-1:00 lan3 (uninitialized): failed to connect to PHY: -EINVAL
mv88e6085 2188000.ethernet-1:00 lan3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 1
mv88e6085 2188000.ethernet-1:00 lan2 (uninitialized): validation of internal with support 00000000,00000000,000062ff and advertisement 00000000,00000000,000062ff failed: -EINVAL
mv88e6085 2188000.ethernet-1:00 lan2 (uninitialized): failed to connect to PHY: -EINVAL
mv88e6085 2188000.ethernet-1:00 lan2 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 2
mv88e6085 2188000.ethernet-1:00 lan1 (uninitialized): validation of internal with support 00000000,00000000,000062ff and advertisement 00000000,00000000,000062ff failed: -EINVAL
mv88e6085 2188000.ethernet-1:00 lan1 (uninitialized): failed to connect to PHY: -EINVAL
mv88e6085 2188000.ethernet-1:00 lan1 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 3
I've run into this message before and had a hard time understanding the issue from the message - it seems to indicate the phy status matches advertisement but that its an invalid mode?
Thanks,
Tim
Andrew Lunn
maintainerQuoted 9 lines
mv88e6085 2188000.ethernet-1:00: Skipping phylink registration for CPU port 5 mv88e6085 2188000.ethernet-1:00 lan4 (uninitialized): PHY [mv88e6xxx-1:00] driver [Generic PHY] (irq=POLL)
mv88e6085 2188000.ethernet-1:00 lan3 (uninitialized): PHY [mv88e6xxx-1:01] driver [Generic PHY] (irq=POLL)
mv88e6085 2188000.ethernet-1:00 lan2 (uninitialized): PHY [mv88e6xxx-1:02] driver [Generic PHY] (irq=POLL)
mv88e6085 2188000.ethernet-1:00 lan1 (uninitialized): PHY [mv88e6xxx-1:03] driver [Generic PHY] (irq=POLL)
Hi Tim
You are using the generic PHY driver, not the Marvell driver. I suggest you fix that first. See if that causes the problem to go away.
Andrew
Hi Tim,
Quoted 8 lines · Tim Harvey
When I add the phy-mode/phy-handle props with this patch I get the
following failure:
mv88e6085 2188000.ethernet-1:00 lan4 (uninitialized): validation of internal with support 00000000,00000000,000062ff and advertisement 00000000,00000000,000062ff failed:-EINVALmv88e6085 2188000.ethernet-1:00 lan4 (uninitialized): failed to connect to PHY:-EINVALI've run into this message before and had a hard time understanding the issue from the message - it seems to indicate the phy status matches advertisement but that its an invalid mode?
Does this patch help?
From 6bd79d9b9994fcb7762301fe297f963c272d9210 Mon Sep 17 00:00:00 2001
From: Vladimir Oltean <[email protected]>
Date: Mon, 5 Dec 2022 19:05:24 +0200
Subject: [PATCH] net: dsa: mv88e6xxx: accept phy-mode = "internal" for
internal PHY ports
The ethernet-controller dt-schema, mostly evolved by Linux, has the "internal" PHY mode for connections between a MAC and internal PHY.
U-Boot may provide device tree blobs where this phy-mode is specified, so make the Linux driver accept them.
--- drivers/net/dsa/mv88e6xxx/chip.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/net/dsa/mv88e6xxx/chip.c +5 -2
@@ -833,10 +833,13 @@ static void mv88e6xxx_get_caps(struct dsa_switch *ds, int port, chip->info->ops->phylink_get_caps (chip, port, config); -/* Internal ports need GMII for PHYLIB */ -if (mv88e6xxx_phy_is_internal (ds, port)) +if (mv88e6xxx_phy_is_internal (ds, port)) { +__set_bit (PHY_INTERFACE_MODE_INTERNAL , + config->supported_interfaces); +/* Internal ports with no phy-mode need GMII for PHYLIB */ __set_bit (PHY_INTERFACE_MODE_GMII , config->supported_interfaces); + } } static void mv88e6xxx_mac_config(struct dsa_switch *ds, int port,
Signature · 1 line
2.34.1
Quoted 53 lines · Vladimir Oltean
Hi Tim,
Quoted 8 lines · Tim Harvey
When I add the phy-mode/phy-handle props with this patch I get the
following failure:
mv88e6085 2188000.ethernet-1:00 lan4 (uninitialized): validation of internal with support 00000000,00000000,000062ff and advertisement 00000000,00000000,000062ff failed:-EINVALmv88e6085 2188000.ethernet-1:00 lan4 (uninitialized): failed to connect to PHY:-EINVALI've run into this message before and had a hard time understanding the issue from the message - it seems to indicate the phy status matches advertisement but that its an invalid mode?
Does this patch help?
From
6bd79d9b9994fcb7762301fe297f963c272d9210Mon Sep 17 00:00:00 2001
From: Vladimir Oltean <[email protected]>
Date: Mon, 5 Dec 2022 19:05:24 +0200
Subject: [PATCH] net: dsa: mv88e6xxx: accept phy-mode = "internal" for
internal PHY portsThe ethernet-controller dt-schema, mostly evolved by Linux, has the "internal" PHY mode for connections between a MAC and internal PHY.
U-Boot may provide device tree blobs where this phy-mode is specified, so make the Linux driver accept them.
Signed-off-by Vladimir Oltean <[email protected]>--- drivers/net/dsa/mv88e6xxx/chip.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)drivers/net/dsa/mv88e6xxx/chip.c +5
-3@@ -833,10 +833,13 @@ static void mv88e6xxx_get_caps(struct dsa_switch *ds, int port, chip->info->ops->phylink_get_caps (chip, port, config); -/* Internal ports need GMII for PHYLIB */ -if (mv88e6xxx_phy_is_internal (ds, port)) +if (mv88e6xxx_phy_is_internal (ds, port)) { +__set_bit (PHY_INTERFACE_MODE_INTERNAL , + config->supported_interfaces); +/* Internal ports with no phy-mode need GMII for PHYLIB */ __set_bit (PHY_INTERFACE_MODE_GMII , config->supported_interfaces); + } } static void mv88e6xxx_mac_config(struct dsa_switch *ds, int port, --
Quoted 2 lines
2.34.1
Vladimir,
Yes, this patch resolves the issue. Enabling CONFIG_MARVELL_PHY without this patch still shows the issue.
Thanks - please cc me on that and I'll respond (unless you want me to send it).
I'll submit a v2 of my dt patch with fec phy-mode = 'rgmii' after this patch lands.
Best Regards,
Tim
Quoted 4 lines · Tim Harvey
Vladimir,
Yes, this patch resolves the issue. Enabling
CONFIG_MARVELL_PHYwithout this patch still shows the issue.
Yeah, that makes sense considering what the issue is.
Quoted 4 lines
Thanks - please cc me on that and I'll respond (unless you want me to send it).
I'll submit a v2 of my dt patch with fec phy-mode = 'rgmii' after this patch lands.
The question is how far to backport this change.
I see that the GW5904 board was introduced in 2017. Which kernels do you need to support the complete/unambiguous dt-binding?
I'm tempted to submit the patch to the "net" tree (making it a candidate for stable releases) but without a Fixes: tag, making it go as far as it will. That would be down to kernel 5.18, where the mv88e6xxx_get_caps() function was introduced. Further down, and we'd need different patches for older stable trees.
Quoted 11 lines · Vladimir Oltean
Quoted 4 lines · Tim Harvey
Vladimir,
Yes, this patch resolves the issue. Enabling
CONFIG_MARVELL_PHYwithout this patch still shows the issue.Yeah, that makes sense considering what the issue is.
Quoted 2 lines
Thanks - please cc me on that and I'll respond (unless you want me to send it).
Quoted 7 lines
Quoted 2 lines
I'll submit a v2 of my dt patch with fec phy-mode = 'rgmii' after this patch lands.
The question is how far to backport this change.
I see that the GW5904 board was introduced in 2017. Which kernels do you need to support the complete/unambiguous dt-binding?
before adding the internal PHY nodes it works fine so no backporting needed. I just don't want to add the complete/unambiguous dt-bindings until your patch lands as at that point it would otherwise be broken.
Best Regards,
Tim
Quoted 6 lines
I'm tempted to submit the patch to the "net" tree (making it a candidate for stable releases) but without a Fixes: tag, making it go as far as it will. That would be down to kernel 5.18, where the
mv88e6xxx_get_caps()function was introduced. Further down, and we'd need different patches for older stable trees.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 3 lines · Tim Harvey
before adding the internal PHY nodes it works fine so no backporting needed. I just don't want to add the complete/unambiguous dt-bindings until your patch lands as at that point it would otherwise be broken.
Right, but there is some debate on whether device tree updates should require new kernel or not. Since in this case, kernels 5.18 and newer can trivially support the updated device trees with this change, I think it would be silly not to let it be backported. As for older kernels, it really depends on what the board ships with.
Quoted 11 lines · Vladimir Oltean
Quoted 3 lines · Tim Harvey
before adding the internal PHY nodes it works fine so no backporting needed. I just don't want to add the complete/unambiguous dt-bindings until your patch lands as at that point it would otherwise be broken.
Right, but there is some debate on whether device tree updates should require new kernel or not. Since in this case, kernels 5.18 and newer can trivially support the updated device trees with this change, I think it would be silly not to let it be backported. As for older kernels, it really depends on what the board ships with.
I see. So then your patch should be backported to when the phy validation was added which would be d4ebf12bcec4 ("net: dsa:
mv88e6xxx: populate supported_interfaces and mac_capabilities") then right?
Best Regards,
Tim
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 4 lines · Tim Harvey
I see. So then your patch should be backported to when the phy validation was added which would be
d4ebf12bcec4("net: dsa:
mv88e6xxx: populatesupported_interfacesandmac_capabilities") then right?
Yup. Actually I suspect that before the commit you're indicating, the mv88e6xxx driver was actually accepting the "internal" phy-mode.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 4 lines · Tim Harvey
Complete the switch definition by adding the internal mdio nodes.
Signed-off-by Tim Harvey <[email protected]>---
Quoted 57 lines
arch/arm/boot/dts/imx6qdl-gw5904.dtsi | 35 +++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)arch/arm/boot/dts/imx6qdl-gw5904.dtsi +27
-0@@ -212,6 +212,27 @@ switch@0 { compatible = "marvell,mv88e6085"; reg = <0>; + mdio { + #address-cells = <1>; + #size-cells = <0>; + + sw_phy0: ethernet-phy@0 { + reg = <0x0>; + }; + + sw_phy1: ethernet-phy@1 { + reg = <0x1>; + }; + + sw_phy2: ethernet-phy@2 { + reg = <0x2>; + }; + + sw_phy3: ethernet-phy@3 { + reg = <0x3>; + }; + }; + ports { #address-cells = <1>; #size-cells = <0>;@@ -219,27 +240,41 @@ ports { port@0 { reg = <0>; label = "lan4"; + phy-handle = <&sw_phy0>; + phy-mode = "internal"; }; port@1 { reg = <1>; label = "lan3"; + phy-handle = <&sw_phy1>; + phy-mode = "internal"; }; port@2 { reg = <2>; label = "lan2"; + phy-handle = <&sw_phy2>; + phy-mode = "internal"; };
arch/arm/boot/dts/imx6qdl-gw5904.dtsi ports { · line 270
Quoted 10 lines
arch/arm/boot/dts/imx6qdl-gw5904.dtsi +2
-0port@3 { reg = <3>; label = "lan1"; + phy-handle = <&sw_phy3>; + phy-mode = "internal"; }; port@5 { reg = <5>; label = "cpu";
The patch context here might conflict with Arınç Ünal's effort to remove label = "cpu" from everywhere.
https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/
Quoted 13 lines
arch/arm/boot/dts/imx6qdl-gw5904.dtsi +6
-0ethernet = <&fec>; + phy-mode = "rgmii-id"; + + fixed-link { + speed = <1000>; + full-duplex; + }; }; }; };Signature · 1 line
2.25.1