PCI: Distribute resources for root buses
v3 cover PCI: Distribute resources for root buses
Hi all,
This is third iteration of the patch series trying to solve the problem reported by Chris Chiu [1]. In summary the current resource distribution code does not cover the initial device enumeration so if we find unconfigured bridges they get the bare minimum.
This one tries to be slightly more generic and deal with PCI devices in addition to PCIe. I've tried this on a system with Maple Ridge Thunderbolt controller (the same as in the orignal bug report), on QEMU with similar PCI topology using following parameters:
-device pcie-pci-bridge,id=br1 \ -device e1000,bus=br1,addr=2 \ -device pci-bridge,chassis_nr=1,bus=br1,shpc=off,id=br2,addr=3 \ -device e1000,bus=br1,addr=4 \ -device e1000,bus=br2
Then on a QEMU similar to what Jonathan used when he found out the regression with multifunction devices:
-device pcie-root-port,port=0,id=root_port13,chassis=0,slot=2 \ -device x3130-upstream,id=sw1,bus=root_port13,multifunction=on \ -device e1000,bus=root_port13,addr=0.1 \ -device xio3130-downstream,id=fun1,bus=sw1,chassis=0,slot=3 \ -device e1000,bus=fun1
The previous versions of the series can be found:
v2: https://lore.kernel.org/linux-pci/[email protected]/
v1: https://lore.kernel.org/linux-pci/[email protected]/
Changes from v2:
* Make both patches to work with PCI devices too (do not expect that the bridge is always first device on the bus).
* Allow distribution with bridges that do not have all resource windows programmed (thereofore the pathch 2/2 is not revert anymore)
* I did not add the tags from Rafael and Jonathan because the code is not exactly the same anymore so was not sure if they still apply.
Changes from v1:
* Re-worded the commit message to hopefully explain the problem better
* Added Link: to the bug report
* Update the comment according to Bjorn's suggestion
* Dropped the ->multifunction check
* Use %#llx in log format.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=216000
Mika Westerberg (2):
PCI: Take other bus devices into account when distributing resources
PCI: Distribute available resources for root buses too
drivers/pci/setup-bus.c | 122 ++++++++++++++++++++++++++++++++++++++-- 1 file changed, 117 insertions(+), 5 deletions(-)
Signature · 1 line
2.35.1
PATCH v3 1/2 PCI: Take other bus devices into account when distributing resources
A PCI bridge may reside on a bus with other devices as well. The resource distribution code does not take this into account properly and therefore it expands the bridge resource windows too much, not leaving space for the other devices (or functions a multifunction device) and this leads to an issue that Jonathan reported. He runs QEMU with the following topoology (QEMU parameters):
-device pcie-root-port,port=0,id=root_port13,chassis=0,slot=2 \
-device x3130-upstream,id=sw1,bus=root_port13,multifunction=on \
-device e1000,bus=root_port13,addr=0.1 \
-device xio3130-downstream,id=fun1,bus=sw1,chassis=0,slot=3 \
-device e1000,bus=fun1
The first e1000 NIC here is another function in the switch upstream port. This leads to following errors:
pci 0000:00:04.0: bridge window [mem 0x10200000-0x103fffff] to [bus 02-04] pci 0000:02:00.0: bridge window [mem 0x10200000-0x103fffff] to [bus 03-04] pci 0000:02:00.1: BAR 0: failed to assign [mem size 0x00020000] e1000 0000:02:00.1: can't ioremap BAR 0: [??? 0x00000000 flags 0x0]
Fix this by taking into account the possible multifunction devices when uptream port resources are distributed.
--- drivers/pci/setup-bus.c | 66 ++++++++++++++++++++++++++++++++++++++--- 1 file changed, 62 insertions(+), 4 deletions(-)
drivers/pci/setup-bus.c +62 -4
@@ -1830,10 +1830,68 @@ static void pci_bus_distribute_available_resources(struct pci_bus *bus,* bridges below. */ if (hotplug_bridges + normal_bridges ==1 ) { - dev = list_first_entry(&bus->devices, struct pci_dev, bus_list); -if (dev->subordinate) -pci_bus_distribute_available_resources (dev->subordinate, - add_list, io, mmio, mmio_pref); + bridge =NULL ; + +/* Find the single bridge on this bus first */ +for_each_pci_bridge (dev, bus) { + bridge = dev; +break ; + } + +if (WARN_ON_ONCE (!bridge)) +return ; +if (!bridge->subordinate) +return ; + +/* +* Reduce the space available for distribution by the +* amount required by the other devices on the same bus +* as this bridge. +*/ +list_for_each_entry (dev, &bus->devices, bus_list) { +int i; + +if (dev == bridge) +continue ; + +for (i =0 ; i <PCI_NUM_RESOURCES ; i++) { +const struct resource *dev_res = &dev->resource[i]; +resource_size_t dev_sz; +struct resource *b_res; + +if (dev_res->flags &IORESOURCE_IO ) { + b_res = &io; + }else if (dev_res->flags &IORESOURCE_MEM ) { +if (dev_res->flags &IORESOURCE_PREFETCH ) + b_res = &mmio_pref; +else + b_res = &mmio; + }else { +continue ; + } + +/* Size aligned to bridge window */ + align =pci_resource_alignment (bridge, b_res); + dev_sz =ALIGN (resource_size (dev_res), align); +if (!dev_sz) +continue ; + +pci_dbg (dev,"resource %pR aligned to %#llx\n" , + dev_res, (unsigned long long )dev_sz); + +if (dev_sz >resource_size (b_res)) +memset (b_res,0 ,sizeof (*b_res)); +else + b_res->end -= dev_sz; + +pci_dbg (bridge,"updated available resources to %pR\n" , + b_res); + } + } + +pci_bus_distribute_available_resources (bridge->subordinate, + add_list, io, mmio, + mmio_pref);return ; }
Signature · 1 line
2.35.1
Re: [PATCH v3 1/2] PCI: Take other bus devices into account when distributing resources
Quoted 21 lines · On Wed, 30 Nov 2022 13:22:20 +0200 Mika Westerberg…
A PCI bridge may reside on a bus with other devices as well. The resource distribution code does not take this into account properly and therefore it expands the bridge resource windows too much, not leaving space for the other devices (or functions a multifunction device) and this leads to an issue that Jonathan reported. He runs QEMU with the following topoology (QEMU parameters):
-device pcie-root-port,port=0,id=root_port13,chassis=0,slot=2 \
-device x3130-upstream,id=sw1,bus=root_port13,multifunction=on \
-device e1000,bus=root_port13,addr=0.1 \
-device xio3130-downstream,id=fun1,bus=sw1,chassis=0,slot=3 \
-device e1000,bus=fun1The first e1000 NIC here is another function in the switch upstream port. This leads to following errors:
pci 0000:00:04.0: bridge window [mem 0x10200000-0x103fffff] to [bus 02-04] pci 0000:02:00.0: bridge window [mem 0x10200000-0x103fffff] to [bus 03-04] pci 0000:02:00.1: BAR 0: failed to assign [mem size
0x00020000] e1000 0000:02:00.1: can't ioremap BAR 0: [???0x00000000flags0x0]
Quoted 6 lines
Fix this by taking into account the possible multifunction devices when uptream port resources are distributed.
Trivial comment inline. Either way..
Quoted 11 lines
--- drivers/pci/setup-bus.c | 66 ++++++++++++++++++++++++++++++++++++++--- 1 file changed, 62 insertions(+), 4 deletions(-)drivers/pci/setup-bus.c +0
-0@@ -1830,10 +1830,68 @@ static void pci_bus_distribute_available_resources(struct pci_bus *bus,* bridges below. */
drivers/pci/setup-bus.c static void pci_bus_distribute_available_resources(struct pci_bus *bus, · line 1837
Quoted 10 lines
drivers/pci/setup-bus.c +4
-4if (hotplug_bridges + normal_bridges ==1 ) { - dev = list_first_entry(&bus->devices, struct pci_dev, bus_list); -if (dev->subordinate) -pci_bus_distribute_available_resources (dev->subordinate, - add_list, io, mmio, mmio_pref); + bridge =NULL ; + +/* Find the single bridge on this bus first */ +for_each_pci_bridge (dev, bus) {
We could cache this a few lines up where we calculate the number of bridges. Perhaps not worth bothering though other than it letting you get rid of the WARN_ON_ONCE.
Quoted 61 lines
drivers/pci/setup-bus.c +58
-0+ bridge = dev; +break ; + } + +if (WARN_ON_ONCE (!bridge)) +return ; +if (!bridge->subordinate) +return ; + +/* +* Reduce the space available for distribution by the +* amount required by the other devices on the same bus +* as this bridge. +*/ +list_for_each_entry (dev, &bus->devices, bus_list) { +int i; + +if (dev == bridge) +continue ; + +for (i =0 ; i <PCI_NUM_RESOURCES ; i++) { +const struct resource *dev_res = &dev->resource[i]; +resource_size_t dev_sz; +struct resource *b_res; + +if (dev_res->flags &IORESOURCE_IO ) { + b_res = &io; + }else if (dev_res->flags &IORESOURCE_MEM ) { +if (dev_res->flags &IORESOURCE_PREFETCH ) + b_res = &mmio_pref; +else + b_res = &mmio; + }else { +continue ; + } + +/* Size aligned to bridge window */ + align =pci_resource_alignment (bridge, b_res); + dev_sz =ALIGN (resource_size (dev_res), align); +if (!dev_sz) +continue ; + +pci_dbg (dev,"resource %pR aligned to %#llx\n" , + dev_res, (unsigned long long )dev_sz); + +if (dev_sz >resource_size (b_res)) +memset (b_res,0 ,sizeof (*b_res)); +else + b_res->end -= dev_sz; + +pci_dbg (bridge,"updated available resources to %pR\n" , + b_res); + } + } + +pci_bus_distribute_available_resources (bridge->subordinate, + add_list, io, mmio, + mmio_pref);return ; }
Re: [PATCH v3 1/2] PCI: Take other bus devices into account when distributing resources
Quoted 12 lines · Jonathan Cameron
Quoted 8 lines · On Wed, 30 Nov 2022 13:22:20 +0200 Mika Westerberg…
drivers/pci/setup-bus.c +3
-4if (hotplug_bridges + normal_bridges ==1 ) { - dev = list_first_entry(&bus->devices, struct pci_dev, bus_list); -if (dev->subordinate) -pci_bus_distribute_available_resources (dev->subordinate, - add_list, io, mmio, mmio_pref); + bridge =NULL ; + +/* Find the single bridge on this bus first */
Quoted 5 lines
drivers/pci/setup-bus.c static void pci_bus_distribute_available_resources(struct pci_bus *bus, · line 1836
Quoted 1 line
drivers/pci/setup-bus.c +1
-0+for_each_pci_bridge (dev, bus) {We could cache this a few lines up where we calculate the number of bridges. Perhaps not worth bothering though other than it letting you get rid of the
WARN_ON_ONCE.
Sorry for repeating this; I saw your response, but it didn't sink in before I responded.
Bjorn
Re: [PATCH v3 1/2] PCI: Take other bus devices into account when distributing resources
In reply to Mika WesterbergHi Mika,
Quoted 4 lines · Mika Westerberg
A PCI bridge may reside on a bus with other devices as well. The resource distribution code does not take this into account properly and therefore it expands the bridge resource windows too much, not leaving space for the other devices (or functions a multifunction device) and
functions *of* a
Quoted 2 lines
this leads to an issue that Jonathan reported. He runs QEMU with the following topoology (QEMU parameters):
topology
Quoted 5 lines
-device pcie-root-port,port=0,id=root_port13,chassis=0,slot=2 \
-device x3130-upstream,id=sw1,bus=root_port13,multifunction=on \
-device e1000,bus=root_port13,addr=0.1 \
-device xio3130-downstream,id=fun1,bus=sw1,chassis=0,slot=3 \
-device e1000,bus=fun1
If you use spaces instead of tabs above, the "\" will stay lined up when git log indents.
Quoted 10 lines
The first e1000 NIC here is another function in the switch upstream port. This leads to following errors:
pci 0000:00:04.0: bridge window [mem 0x10200000-0x103fffff] to [bus 02-04] pci 0000:02:00.0: bridge window [mem 0x10200000-0x103fffff] to [bus 03-04] pci 0000:02:00.1: BAR 0: failed to assign [mem size
0x00020000] e1000 0000:02:00.1: can't ioremap BAR 0: [???0x00000000flags0x0]Fix this by taking into account the possible multifunction devices when uptream port resources are distributed.
"upstream", although I think I would word this so it's less PCIe-centric. IIUC, we just want to account for all the BARs on the bus, whether they're in bridges, peers in a multi-function device, or other devices.
Quoted 16 lines
Reported-by Jonathan Cameron <[email protected]>Signed-off-by Mika Westerberg <[email protected]>--- drivers/pci/setup-bus.c | 66 ++++++++++++++++++++++++++++++++++++++--- 1 file changed, 62 insertions(+), 4 deletions(-)drivers/pci/setup-bus.c +0
-1@@ -1830,10 +1830,68 @@ static void pci_bus_distribute_available_resources(struct pci_bus *bus,* bridges below. */ if (hotplug_bridges + normal_bridges ==1 ) { - dev = list_first_entry(&bus->devices, struct pci_dev, bus_list);
drivers/pci/setup-bus.c static void pci_bus_distribute_available_resources(struct pci_bus *bus, · line 1839
Quoted 10 lines
drivers/pci/setup-bus.c +7
-3-if (dev->subordinate) -pci_bus_distribute_available_resources (dev->subordinate, - add_list, io, mmio, mmio_pref); + bridge =NULL ; + +/* Find the single bridge on this bus first */ +for_each_pci_bridge (dev, bus) { + bridge = dev; +break ; + }
If we just remember "bridge" in the loop before this hunk, could we get rid of the loop here? E.g.,
bridge = NULL;
for_each_pci_bridge(dev, bus) {
bridge = dev;
if (dev->is_hotplug_bridge)
hotplug_bridges++;
else
normal_bridges++;
}drivers/pci/setup-bus.c static void pci_bus_distribute_available_resources(struct pci_bus *bus, · line 1842
Quoted 3 lines
drivers/pci/setup-bus.c +3
-0+ +if (WARN_ON_ONCE (!bridge)) +return ;
Then I think this would be superfluous.
drivers/pci/setup-bus.c static void pci_bus_distribute_available_resources(struct pci_bus *bus, · line 1855
Quoted 13 lines
drivers/pci/setup-bus.c +13
-0+if (!bridge->subordinate) +return ; + +/* +* Reduce the space available for distribution by the +* amount required by the other devices on the same bus +* as this bridge. +*/ +list_for_each_entry (dev, &bus->devices, bus_list) { +int i; + +if (dev == bridge) +continue ;
Why do we skip "bridge"? Bridges are allowed to have two BARs themselves, and it seems like they should be included here.
Quoted 24 lines
drivers/pci/setup-bus.c +24
-0+for (i =0 ; i <PCI_NUM_RESOURCES ; i++) { +const struct resource *dev_res = &dev->resource[i]; +resource_size_t dev_sz; +struct resource *b_res; + +if (dev_res->flags &IORESOURCE_IO ) { + b_res = &io; + }else if (dev_res->flags &IORESOURCE_MEM ) { +if (dev_res->flags &IORESOURCE_PREFETCH ) + b_res = &mmio_pref; +else + b_res = &mmio; + }else { +continue ; + } + +/* Size aligned to bridge window */ + align =pci_resource_alignment (bridge, b_res); + dev_sz =ALIGN (resource_size (dev_res), align); +if (!dev_sz) +continue ; + +pci_dbg (dev,"resource %pR aligned to %#llx\n" , + dev_res, (unsigned long long )dev_sz);
drivers/pci/setup-bus.c static void pci_bus_distribute_available_resources(struct pci_bus *bus, · line 1890
Quoted 10 lines
drivers/pci/setup-bus.c +10
-0+ +if (dev_sz >resource_size (b_res)) +memset (b_res,0 ,sizeof (*b_res)); +else + b_res->end -= dev_sz; + +pci_dbg (bridge,"updated available resources to %pR\n" , + b_res); + } + }
This only happens for buses with a single bridge. Shouldn't it happen regardless of how many bridges there are?
This block feels like something that could be split out to a separate function. It looks like it only needs "bus", "io", "mmio", "mmio_pref", and maybe "bridge".
I don't understand the "bridge" part; it looks like that's basically to use 4K alignment for I/O windows and 1M for memory windows? Using "bridge" seems like a clunky way to figure that out.
Bjorn
Re: [PATCH v3 1/2] PCI: Take other bus devices into account when distributing resources
Hi,
Quoted 15 lines · Bjorn Helgaas
Hi Mika,
Quoted 4 lines · Mika Westerberg
A PCI bridge may reside on a bus with other devices as well. The resource distribution code does not take this into account properly and therefore it expands the bridge resource windows too much, not leaving space for the other devices (or functions a multifunction device) and
functions *of* a
Quoted 2 lines
this leads to an issue that Jonathan reported. He runs QEMU with the following topoology (QEMU parameters):
topology
Quoted 8 lines
Quoted 5 lines
-device pcie-root-port,port=0,id=root_port13,chassis=0,slot=2 \
-device x3130-upstream,id=sw1,bus=root_port13,multifunction=on \
-device e1000,bus=root_port13,addr=0.1 \
-device xio3130-downstream,id=fun1,bus=sw1,chassis=0,slot=3 \
-device e1000,bus=fun1If you use spaces instead of tabs above, the "\" will stay lined up when git log indents.
Sure.
Quoted 8 lines
Quoted 8 lines
The first e1000 NIC here is another function in the switch upstream port. This leads to following errors:
pci 0000:00:04.0: bridge window [mem 0x10200000-0x103fffff] to [bus 02-04] pci 0000:02:00.0: bridge window [mem 0x10200000-0x103fffff] to [bus 03-04] pci 0000:02:00.1: BAR 0: failed to assign [mem size
0x00020000] e1000 0000:02:00.1: can't ioremap BAR 0: [???0x00000000flags0x0]
Quoted 7 lines
Quoted 2 lines
Fix this by taking into account the possible multifunction devices when uptream port resources are distributed.
"upstream", although I think I would word this so it's less PCIe-centric. IIUC, we just want to account for all the BARs on the bus, whether they're in bridges, peers in a multi-function device, or other devices.
Okay.
Quoted 30 lines
Quoted 16 lines
Reported-by Jonathan Cameron <[email protected]>Signed-off-by Mika Westerberg <[email protected]>--- drivers/pci/setup-bus.c | 66 ++++++++++++++++++++++++++++++++++++++--- 1 file changed, 62 insertions(+), 4 deletions(-)drivers/pci/setup-bus.c +0
-1@@ -1830,10 +1830,68 @@ static void pci_bus_distribute_available_resources(struct pci_bus *bus,* bridges below. */ if (hotplug_bridges + normal_bridges ==1 ) { - dev = list_first_entry(&bus->devices, struct pci_dev, bus_list);drivers/pci/setup-bus.c static void pci_bus_distribute_available_resources(struct pci_bus *bus, · line 1839
Quoted 10 lines
drivers/pci/setup-bus.c +7
-3-if (dev->subordinate) -pci_bus_distribute_available_resources (dev->subordinate, - add_list, io, mmio, mmio_pref); + bridge =NULL ; + +/* Find the single bridge on this bus first */ +for_each_pci_bridge (dev, bus) { + bridge = dev; +break ; + }If we just remember "bridge" in the loop before this hunk, could we get rid of the loop here? E.g.,
Quoted 8 lines
bridge = NULL;
for_each_pci_bridge(dev, bus) {
bridge = dev;
if (dev->is_hotplug_bridge)
hotplug_bridges++;
else
normal_bridges++;
}Yes, I think that would work too.
Quoted 6 lines
drivers/pci/setup-bus.c static void pci_bus_distribute_available_resources(struct pci_bus *bus, · line 1842
Quoted 3 lines
drivers/pci/setup-bus.c +3
-0+ +if (WARN_ON_ONCE (!bridge)) +return ;Then I think this would be superfluous.
Quoted 16 lines
drivers/pci/setup-bus.c static void pci_bus_distribute_available_resources(struct pci_bus *bus, · line 1855
Quoted 13 lines
drivers/pci/setup-bus.c +13
-0+if (!bridge->subordinate) +return ; + +/* +* Reduce the space available for distribution by the +* amount required by the other devices on the same bus +* as this bridge. +*/ +list_for_each_entry (dev, &bus->devices, bus_list) { +int i; + +if (dev == bridge) +continue ;Why do we skip "bridge"? Bridges are allowed to have two BARs themselves, and it seems like they should be included here.
Good point but then we would need to skip below the bridge window resources to avoid accounting them.
Quoted 29 lines
Quoted 29 lines
drivers/pci/setup-bus.c +29
-0+for (i =0 ; i <PCI_NUM_RESOURCES ; i++) { +const struct resource *dev_res = &dev->resource[i]; +resource_size_t dev_sz; +struct resource *b_res; + +if (dev_res->flags &IORESOURCE_IO ) { + b_res = &io; + }else if (dev_res->flags &IORESOURCE_MEM ) { +if (dev_res->flags &IORESOURCE_PREFETCH ) + b_res = &mmio_pref; +else + b_res = &mmio; + }else { +continue ; + } + +/* Size aligned to bridge window */ + align =pci_resource_alignment (bridge, b_res); + dev_sz =ALIGN (resource_size (dev_res), align); +if (!dev_sz) +continue ; + +pci_dbg (dev,"resource %pR aligned to %#llx\n" , + dev_res, (unsigned long long )dev_sz); + +if (dev_sz >resource_size (b_res)) +memset (b_res,0 ,sizeof (*b_res)); +else + b_res->end -= dev_sz;
Quoted 8 lines
drivers/pci/setup-bus.c static void pci_bus_distribute_available_resources(struct pci_bus *bus, · line 1890
Quoted 5 lines
drivers/pci/setup-bus.c +5
-0+ +pci_dbg (bridge,"updated available resources to %pR\n" , + b_res); + } + }This only happens for buses with a single bridge. Shouldn't it happen regardless of how many bridges there are?
This branch specifically deals with the "upstream port" so it gives all the spare resources to that upstream port. The whole resource distribution is actually done to accommondate Thunderbolt/USB4 topologies which involve only PCIe devices so we always have PCIe upstream port and downstream ports which some of them are able to perform native PCIe hotplug. And for those ports we want to distribute the available resources so that they can expand to further topologies.
I'm slightly concerned that forcing this to support the "generic" PCI case makes this rather complicated. This is something that never appears in the regular PCI based systems because we never distribute resources for those in the first place (->is_hotplug_bridge needs to be set).
Quoted 3 lines
This block feels like something that could be split out to a separate function. It looks like it only needs "bus", "io", "mmio", "
mmio_pref", and maybe "bridge".
Makes sense.
Quoted 3 lines
I don't understand the "bridge" part; it looks like that's basically to use 4K alignment for I/O windows and 1M for memory windows? Using "bridge" seems like a clunky way to figure that out.
Okay, but if not using "bridge", how exactly you suggest to doing the calculation?
Re: [PATCH v3 1/2] PCI: Take other bus devices into account when distributing resources
Quoted 20 lines · Mika Westerberg
Quoted 6 lines · Bjorn Helgaas
Quoted 4 lines · Mika Westerberg
A PCI bridge may reside on a bus with other devices as well. The resource distribution code does not take this into account properly and therefore it expands the bridge resource windows too much, not leaving space for the other devices (or functions a multifunction device) and
Quoted 12 lines
drivers/pci/setup-bus.c static void pci_bus_distribute_available_resources(struct pci_bus *bus, · line 1855
Quoted 9 lines
drivers/pci/setup-bus.c +9
-0+* Reduce the space available for distribution by the +* amount required by the other devices on the same bus +* as this bridge. +*/ +list_for_each_entry (dev, &bus->devices, bus_list) { +int i; + +if (dev == bridge) +continue ;Why do we skip "bridge"? Bridges are allowed to have two BARs themselves, and it seems like they should be included here.
Quoted 2 lines
Good point but then we would need to skip below the bridge window resources to avoid accounting them.
Seems like we should handle bridge BARs. There are definitely bridges (PCIe for sure, I dunno about conventional PCI) that implement them and some drivers starting to appear that use them for performance monitoring, etc.
Quoted 11 lines
Quoted 2 lines
This only happens for buses with a single bridge. Shouldn't it happen regardless of how many bridges there are?
This branch specifically deals with the "upstream port" so it gives all the spare resources to that upstream port. The whole resource distribution is actually done to accommondate Thunderbolt/USB4 topologies which involve only PCIe devices so we always have PCIe upstream port and downstream ports which some of them are able to perform native PCIe hotplug. And for those ports we want to distribute the available resources so that they can expand to further topologies.
Quoted 4 lines
I'm slightly concerned that forcing this to support the "generic" PCI case makes this rather complicated. This is something that never appears in the regular PCI based systems because we never distribute resources for those in the first place (->is_hotplug_bridge needs to be set).
This code is fairly complicated in any case :)
I understand why this is useful for Thunderbolt topologies, but it should be equally useful for other hotplug topologies because at this level we're purely talking about the address space needed by devices and how that space is assigned and routed through bridges. Nothing unique to Thunderbolt here.
I don't think we should make this PCIe-specific. ->is_hotplug_bridge is set by a PCIe path (set_pcie_hotplug_bridge()), but also by check_hotplug_bridge() in acpiphp, which could be any flavor of PCI, and I don't think there's anything intrinsically PCIe-specific about it.
Quoted 6 lines
Quoted 3 lines
I don't understand the "bridge" part; it looks like that's basically to use 4K alignment for I/O windows and 1M for memory windows? Using "bridge" seems like a clunky way to figure that out.
Okay, but if not using "bridge", how exactly you suggest to doing the calculation?
I was thinking it would always be 4K or 1M, but I guess that's actually not true. There are some Intel bridges that support 1K alignment for I/O windows, and some powerpc hypervisor stuff that can also influence the alignment. And it looks like we still need to figure out which b_res to use, so we couldn't get rid of the IO/MEM case analysis. So never mind, I guess ...
Bjorn
PATCH v3 2/2 PCI: Distribute available resources for root buses too
In reply to Mika WesterbergPreviously we distributed spare resources only upon hot-add, so if the initial root bus scan found devices that had not been fully configured by the BIOS, we allocated only enough resources to cover what was then present. If some of those devices were hotplug bridges, we did not leave any additional resource space for future expansion.
Distribute the available resources for root buses, too, to make this work the same way as the normal hotplug case.
---
This is a new version of the patch after the revert due to the regression reported by Jonathan Cameron. This one changes pci_bridge_resources_not_assigned() to work with bridges that do not have all the resource windows programmed by the boot firmware (previously we expected all I/O, memory and prefetchable memory were all programmed).
drivers/pci/setup-bus.c | 56 ++++++++++++++++++++++++++++++++++++++++- 1 file changed, 55 insertions(+), 1 deletion(-)
drivers/pci/setup-bus.c +55 -1
@@ -1768,7 +1768,10 @@ static void adjust_bridge_window(struct pci_dev *bridge, struct resource *res, } res->end = res->start + new_size -1 ; -remove_from_list (add_list, res); + +/* If the resource is part of the add_list remove it now */ +if (add_list) +remove_from_list (add_list, res); } static void pci_bus_distribute_available_resources(struct pci_bus *bus,
@@ -1981,6 +1984,8 @@ static void pci_bridge_distribute_available_resources(struct pci_dev *bridge,if (!bridge->is_hotplug_bridge)return ; +pci_dbg (bridge,"distributing available resources\n" ); +/* Take the initial extra resources from the hotplug port */ available_io = bridge->resource[PCI_BRIDGE_IO_WINDOW ]; available_mmio = bridge->resource[PCI_BRIDGE_MEM_WINDOW ];
@@ -1992,6 +1997,53 @@ static void pci_bridge_distribute_available_resources(struct pci_dev *bridge, available_mmio_pref); } +static bool pci_bridge_resources_not_assigned (struct pci_dev *dev) +{ +const struct resource *r; + +/* +* Check the child device's resources and if they are not yet +* assigned it means we are configuring them (not the boot +* firmware) so we should be able to extend the upstream +* bridge's (that's the hotplug downstream PCIe port) resources +* in the same way we do with the normal hotplug case. +*/ + r = &dev->resource[PCI_BRIDGE_IO_WINDOW ]; +if (r->flags && !(r->flags &IORESOURCE_STARTALIGN )) +return false; + r = &dev->resource[PCI_BRIDGE_MEM_WINDOW ]; +if (r->flags && !(r->flags &IORESOURCE_STARTALIGN )) +return false; + r = &dev->resource[PCI_BRIDGE_PREF_MEM_WINDOW ]; +if (r->flags && !(r->flags &IORESOURCE_STARTALIGN )) +return false; + +return true; +} + +static void pci_root_bus_distribute_available_resources (struct pci_bus *bus, +struct list_head *add_list) +{ +struct pci_dev *dev, *bridge = bus->self; + +for_each_pci_bridge (dev, bus) { +struct pci_bus *b; + + b = dev->subordinate; +if (!b) +continue ; + +/* +* Need to check "bridge" here too because it is NULL +* in case of root bus. +*/ +if (bridge &&pci_bridge_resources_not_assigned (dev)) +pci_bridge_distribute_available_resources (bridge, add_list); +else +pci_root_bus_distribute_available_resources (b, add_list); + } +} +/* * First try will not touch PCI bridge res. * Second and later try will clear small leaf bridge res.
@@ -2031,6 +2083,8 @@ void pci_assign_unassigned_root_bus_resources(struct pci_bus *bus)*/ __pci_bus_size_bridges (bus, add_list); +pci_root_bus_distribute_available_resources (bus, add_list); +/* Depth last, allocate resources and update the hardware. */ __pci_bus_assign_resources (bus, add_list, &fail_head);if (add_list)
Signature · 1 line
2.35.1
Re: [PATCH v3 2/2] PCI: Distribute available resources for root buses too
Quoted 13 lines · On Wed, 30 Nov 2022 13:22:21 +0200 Mika Westerberg…
Previously we distributed spare resources only upon hot-add, so if the initial root bus scan found devices that had not been fully configured by the BIOS, we allocated only enough resources to cover what was then present. If some of those devices were hotplug bridges, we did not leave any additional resource space for future expansion.
Distribute the available resources for root buses, too, to make this work the same way as the normal hotplug case.
Quoted 7 lines
---
This is a new version of the patch after the revert due to the regression reported by Jonathan Cameron. This one changespci_bridge_resources_not_assigned()to work with bridges that do not have all the resource windows programmed by the boot firmware (previously we expected all I/O, memory and prefetchable memory were all programmed).
Whilst this sounds plausible my understanding of how those flags are used is very minimal so I'll leave this one for others to review who hopefully already know how that works!
Quoted 55 lines
drivers/pci/setup-bus.c | 56 ++++++++++++++++++++++++++++++++++++++++- 1 file changed, 55 insertions(+), 1 deletion(-)drivers/pci/setup-bus.c +29
-1@@ -1768,7 +1768,10 @@ static void adjust_bridge_window(struct pci_dev *bridge, struct resource *res, } res->end = res->start + new_size -1 ; -remove_from_list (add_list, res); + +/* If the resource is part of the add_list remove it now */ +if (add_list) +remove_from_list (add_list, res); } static void pci_bus_distribute_available_resources(struct pci_bus *bus,@@ -1981,6 +1984,8 @@ static void pci_bridge_distribute_available_resources(struct pci_dev *bridge,if (!bridge->is_hotplug_bridge)return ; +pci_dbg (bridge,"distributing available resources\n" ); +/* Take the initial extra resources from the hotplug port */ available_io = bridge->resource[PCI_BRIDGE_IO_WINDOW ]; available_mmio = bridge->resource[PCI_BRIDGE_MEM_WINDOW ];@@ -1992,6 +1997,53 @@ static void pci_bridge_distribute_available_resources(struct pci_dev *bridge, available_mmio_pref); } +static bool pci_bridge_resources_not_assigned (struct pci_dev *dev) +{ +const struct resource *r; + +/* +* Check the child device's resources and if they are not yet +* assigned it means we are configuring them (not the boot +* firmware) so we should be able to extend the upstream +* bridge's (that's the hotplug downstream PCIe port) resources +* in the same way we do with the normal hotplug case. +*/ + r = &dev->resource[PCI_BRIDGE_IO_WINDOW ]; +if (r->flags && !(r->flags &IORESOURCE_STARTALIGN )) +return false; + r = &dev->resource[PCI_BRIDGE_MEM_WINDOW ]; +if (r->flags && !(r->flags &IORESOURCE_STARTALIGN )) +return false; + r = &dev->resource[PCI_BRIDGE_PREF_MEM_WINDOW ]; +if (r->flags && !(r->flags &IORESOURCE_STARTALIGN )) +return false; + +return true; +}
Quoted 29 lines · On Wed, 30 Nov 2022 13:22:19 +0200 Mika Westerberg…
Hi all,
This is third iteration of the patch series trying to solve the problem reported by Chris Chiu [1]. In summary the current resource distribution code does not cover the initial device enumeration so if we find unconfigured bridges they get the bare minimum.
This one tries to be slightly more generic and deal with PCI devices in addition to PCIe. I've tried this on a system with Maple Ridge Thunderbolt controller (the same as in the orignal bug report), on QEMU with similar PCI topology using following parameters:
-device pcie-pci-bridge,id=br1 \ -device e1000,bus=br1,addr=2 \ -device pci-bridge,chassis_nr=1,bus=br1,shpc=off,id=br2,addr=3 \ -device e1000,bus=br1,addr=4 \ -device e1000,bus=br2Then on a QEMU similar to what Jonathan used when he found out the regression with multifunction devices:
-device pcie-root-port,port=0,id=root_port13,chassis=0,slot=2 \ -device x3130-upstream,id=sw1,bus=root_port13,multifunction=on \ -device e1000,bus=root_port13,addr=0.1 \ -device xio3130-downstream,id=fun1,bus=sw1,chassis=0,slot=3 \ -device e1000,bus=fun1The previous versions of the series can be found:
Quoted 8 lines
v2: https://lore.kernel.org/linux-pci/[email protected]/
v1: https://lore.kernel.org/linux-pci/[email protected]/Changes from v2:
* Make both patches to work with PCI devices too (do not expect that the bridge is always first device on the bus).
* Allow distribution with bridges that do not have all resource windows programmed (thereofore the pathch 2/2 is not revert anymore)
patch
Quoted 2 lines
* I did not add the tags from Rafael and Jonathan because the code is not exactly the same anymore so was not sure if they still apply.
Fair enough - guess it's time for another look.
Quoted 17 lines
Changes from v1:
* Re-worded the commit message to hopefully explain the problem better
* Added Link: to the bug report
* Update the comment according to Bjorn's suggestion
* Dropped the ->multifunction check
* Use %#llx in log format.[1] https://bugzilla.kernel.org/show_bug.cgi?id=216000
Mika Westerberg (2):
PCI: Take other bus devices into account when distributing resources
PCI: Distribute available resources for root buses toodrivers/pci/setup-bus.c | 122 ++++++++++++++++++++++++++++++++++++++-- 1 file changed, 117 insertions(+), 5 deletions(-)