ARM: stm32: Fix ECDSA authentication with Dcache enabled
Subsystems (3)
PATCH v3 1/4 ARM: stm32: Fix ECDSA authentication with Dcache enabled
In case Dcache is enabled while the ECDSA authentication function is called via BootROM ROM API, the MMU tables are set up and the BootROM region is not marked as executable, so an attempt to run code from it results in a hang. Mark the BootROM region as executable as suggested by Patrick to prevent the hang.
---
Cc: Alexandru Gagniuc <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
---
V2: - Initialize reenable_dcache variable
V3: - Mark BootROM as executable instead
--- arch/arm/mach-stm32mp/ecdsa_romapi.c | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm/mach-stm32mp/ecdsa_romapi.c +4 -0
@@ -81,6 +81,10 @@ static int romapi_ecdsa_verify(struct udevice *dev,memcpy (raw_key +32 , pubkey->y,32 );stm32mp_rom_get_ecdsa_functions (&rom); + +/* Mark BootROM region as executable. */ +mmu_set_region_dcache_behaviour (0 ,SZ_2M ,DCACHE_DEFAULT_OPTION ); + rom_ret = rom.ecdsa_verify_signature (hash, raw_key, signature, algo);return rom_ret ==ROM_API_SUCCESS ?0 : -EPERM ;
Signature · 1 line
2.35.1
PATCH v3 2/4 ARM: stm32: Factor out save_boot_params
The STM32MP15xx platform currently comes with two incompatible implementations of save_boot_params() weak function override. Factor the save_boot_params() implementation into common cpu.c code and provide accessors to read out both ROM API table address and DT address from any place in the code instead.
---
Cc: Alexandru Gagniuc <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
---
V2: Avoid #if CONFIG... , use if (CONFIG... instead
V3: No change
--- arch/arm/mach-stm32mp/boot_params.c | 20 ++--------- arch/arm/mach-stm32mp/cpu.c | 35 +++++++++++++++++++ arch/arm/mach-stm32mp/ecdsa_romapi.c | 20 ++--------- .../arm/mach-stm32mp/include/mach/sys_proto.h | 3 ++ 4 files changed, 42 insertions(+), 36 deletions(-)
arch/arm/mach-stm32mp/boot_params.c +2 -18
@@ -11,30 +11,14 @@#include <asm/sections.h> #include <asm/system.h> -/* -* Force data-section, as .bss will not be valid -* when save_boot_params is invoked. -*/ -static unsigned long nt_fw_dtb __section(".data"); - -/* -* Save the FDT address provided by TF-A in r2 at boot time -* This function is called from start.S -*/ -void save_boot_params (unsigned long r0,unsigned long r1,unsigned long r2, -unsigned long r3) -{ - nt_fw_dtb = r2; - -save_boot_params_ret (); -} -/* * Use the saved FDT address provided by TF-A at boot time (NT_FW_CONFIG = * Non Trusted Firmware configuration file) when the pointer is valid */ void *board_fdt_blob_setup (int *err) { +unsigned long nt_fw_dtb =get_stm32mp_bl2_dtb (); +log_debug ("%s: nt_fw_dtb=%lx\n" , __func__, nt_fw_dtb); *err =0 ;
arch/arm/mach-stm32mp/cpu.c +35 -0
@@ -378,3 +378,38 @@ int arch_misc_init(void)return 0 ; } + +/* +* Without forcing the ".data" section, this would get saved in ".bss". BSS +* will be cleared soon after, so it's not suitable. +*/ +static uintptr_t rom_api_table __section(".data"); +static uintptr_t nt_fw_dtb __section(".data"); + +/* +* The ROM gives us the API location in r0 when starting. This is only available +* during SPL, as there isn't (yet) a mechanism to pass this on to u-boot. Save +* the FDT address provided by TF-A in r2 at boot time. This function is called +* from start.S +*/ +void save_boot_params (unsigned long r0,unsigned long r1,unsigned long r2, +unsigned long r3) +{ +if (IS_ENABLED (CONFIG_STM32_ECDSA_VERIFY )) + rom_api_table = r0; + +if (IS_ENABLED (CONFIG_TFABOOT )) + nt_fw_dtb = r2; + +save_boot_params_ret (); +} + +uintptr_t get_stm32mp_rom_api_table (void ) +{ +return rom_api_table; +} + +uintptr_t get_stm32mp_bl2_dtb (void ) +{ +return nt_fw_dtb; +}
arch/arm/mach-stm32mp/ecdsa_romapi.c +2 -18
@@ -24,26 +24,10 @@ struct ecdsa_rom_api { uint32_t ecc_algo); }; -/* -* Without forcing the ".data" section, this would get saved in ".bss". BSS -* will be cleared soon after, so it's not suitable. -*/ -static uintptr_t rom_api_loc __section(".data"); - -/* -* The ROM gives us the API location in r0 when starting. This is only available -* during SPL, as there isn't (yet) a mechanism to pass this on to u-boot. -*/ -void save_boot_params (unsigned long r0,unsigned long r1,unsigned long r2, -unsigned long r3) -{ - rom_api_loc = r0; -save_boot_params_ret (); -} -static void stm32mp_rom_get_ecdsa_functions (struct ecdsa_rom_api *rom) { -uintptr_t verify_ptr = rom_api_loc +ROM_API_OFFSET_ECDSA_VERIFY ; +uintptr_t verify_ptr =get_stm32mp_rom_api_table () + +ROM_API_OFFSET_ECDSA_VERIFY ; rom->ecdsa_verify_signature = *(void **)verify_ptr; }
arch/arm/mach-stm32mp/include/mach/sys_proto.h +3 -0
@@ -77,3 +77,6 @@ void stm32mp_misc_init(void);/* helper function: read data from OTP */ u32 get_otp (int index,int shift,int mask); + +uintptr_t get_stm32mp_rom_api_table (void ); +uintptr_t get_stm32mp_bl2_dtb (void );
Signature · 1 line
2.35.1
Re: [PATCH v3 2/4] ARM: stm32: Factor out save_boot_params
Hi,
Quoted 14 lines · Marek Vasut
The STM32MP15xx platform currently comes with two incompatible implementations of
save_boot_params()weak function override. Factor thesave_boot_params()implementation into commoncpu.ccode and provide accessors to read out both ROM API table address and DT address from any place in the code instead.Signed-off-by Marek Vasut <[email protected]>---
Cc: Alexandru Gagniuc <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
---
V2: Avoid #if CONFIG... , use if (CONFIG... instead
V3: No change
Quoted 6 lines
--- arch/arm/mach-stm32mp/boot_params.c | 20 ++--------- arch/arm/mach-stm32mp/cpu.c | 35 +++++++++++++++++++ arch/arm/mach-stm32mp/ecdsa_romapi.c | 20 ++--------- .../arm/mach-stm32mp/include/mach/sys_proto.h | 3 ++ 4 files changed, 42 insertions(+), 36 deletions(-)
Thanks
Patrick
Re: [PATCH v3 2/4] ARM: stm32: Factor out save_boot_params
In reply to Marek VasutHi Marek
Quoted 139 lines · Marek Vasut
The STM32MP15xx platform currently comes with two incompatible implementations of
save_boot_params()weak function override. Factor thesave_boot_params()implementation into commoncpu.ccode and provide accessors to read out both ROM API table address and DT address from any place in the code instead.Signed-off-by Marek Vasut <[email protected]>---
Cc: Alexandru Gagniuc <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
---
V2: Avoid #if CONFIG... , use if (CONFIG... instead
V3: No change--- arch/arm/mach-stm32mp/boot_params.c | 20 ++--------- arch/arm/mach-stm32mp/cpu.c | 35 +++++++++++++++++++ arch/arm/mach-stm32mp/ecdsa_romapi.c | 20 ++--------- .../arm/mach-stm32mp/include/mach/sys_proto.h | 3 ++ 4 files changed, 42 insertions(+), 36 deletions(-)arch/arm/mach-stm32mp/boot_params.c +2
-18@@ -11,30 +11,14 @@#include <asm/sections.h> #include <asm/system.h> -/* -* Force data-section, as .bss will not be valid -* when save_boot_params is invoked. -*/ -static unsigned long nt_fw_dtb __section(".data"); - -/* -* Save the FDT address provided by TF-A in r2 at boot time -* This function is called from start.S -*/ -void save_boot_params (unsigned long r0,unsigned long r1,unsigned long r2, -unsigned long r3) -{ - nt_fw_dtb = r2; - -save_boot_params_ret (); -} -/* * Use the saved FDT address provided by TF-A at boot time (NT_FW_CONFIG = * Non Trusted Firmware configuration file) when the pointer is valid */ void *board_fdt_blob_setup (int *err) { +unsigned long nt_fw_dtb =get_stm32mp_bl2_dtb (); +log_debug ("%s: nt_fw_dtb=%lx\n" , __func__, nt_fw_dtb); *err =0 ;arch/arm/mach-stm32mp/cpu.c +35
-0@@ -378,3 +378,38 @@ int arch_misc_init(void)return 0 ; } + +/* +* Without forcing the ".data" section, this would get saved in ".bss". BSS +* will be cleared soon after, so it's not suitable. +*/ +static uintptr_t rom_api_table __section(".data"); +static uintptr_t nt_fw_dtb __section(".data"); + +/* +* The ROM gives us the API location in r0 when starting. This is only available +* during SPL, as there isn't (yet) a mechanism to pass this on to u-boot. Save +* the FDT address provided by TF-A in r2 at boot time. This function is called +* from start.S +*/ +void save_boot_params (unsigned long r0,unsigned long r1,unsigned long r2, +unsigned long r3) +{ +if (IS_ENABLED (CONFIG_STM32_ECDSA_VERIFY )) + rom_api_table = r0; + +if (IS_ENABLED (CONFIG_TFABOOT )) + nt_fw_dtb = r2; + +save_boot_params_ret (); +} + +uintptr_t get_stm32mp_rom_api_table (void ) +{ +return rom_api_table; +} + +uintptr_t get_stm32mp_bl2_dtb (void ) +{ +return nt_fw_dtb; +}arch/arm/mach-stm32mp/ecdsa_romapi.c +2
-18@@ -24,26 +24,10 @@ struct ecdsa_rom_api { uint32_t ecc_algo); }; -/* -* Without forcing the ".data" section, this would get saved in ".bss". BSS -* will be cleared soon after, so it's not suitable. -*/ -static uintptr_t rom_api_loc __section(".data"); - -/* -* The ROM gives us the API location in r0 when starting. This is only available -* during SPL, as there isn't (yet) a mechanism to pass this on to u-boot. -*/ -void save_boot_params (unsigned long r0,unsigned long r1,unsigned long r2, -unsigned long r3) -{ - rom_api_loc = r0; -save_boot_params_ret (); -} -static void stm32mp_rom_get_ecdsa_functions (struct ecdsa_rom_api *rom) { -uintptr_t verify_ptr = rom_api_loc +ROM_API_OFFSET_ECDSA_VERIFY ; +uintptr_t verify_ptr =get_stm32mp_rom_api_table () + +ROM_API_OFFSET_ECDSA_VERIFY ; rom->ecdsa_verify_signature = *(void **)verify_ptr; }arch/arm/mach-stm32mp/include/mach/sys_proto.h +0
-0
arch/arm/mach-stm32mp/include/mach/sys_proto.h void stm32mp_misc_init(void); · line 82
Quoted 6 lines
arch/arm/mach-stm32mp/include/mach/sys_proto.h +3
-0@@ -77,3 +77,6 @@ void stm32mp_misc_init(void);/* helper function: read data from OTP */ u32 get_otp (int index,int shift,int mask); + +uintptr_t get_stm32mp_rom_api_table (void ); +uintptr_t get_stm32mp_bl2_dtb (void );
Thanks
Patrice
Re: [PATCH v3 2/4] ARM: stm32: Factor out save_boot_params
Hi Marek
I am preparing the next STM32 U-Boot pull request, during testing, buidlman is complaining with the following warning:
03: ARM: stm32: Factor out save_boot_params
arm: + stm32mp13
+../arch/arm/mach-stm32mp/boot_params.c: In function 'board_fdt_blob_setup':+../arch/arm/mach-stm32mp/boot_params.c:20:35: error: implicit declaration of function 'get_stm32mp_bl2_dtb' [-Werror=implicit-function-declaration]
+ 20 | unsigned long nt_fw_dtb = get_stm32mp_bl2_dtb();
+ | ^~~~~~~~~~~~~~~~~~~
+cc1: all warnings being treated as errors
Same issue with stm32mp15_defconfig and stm32mp15_trusted_defconfig.
Regards
Patrice
Quoted 153 lines · Patrice CHOTARD
Hi Marek
Quoted 139 lines · Marek Vasut
The STM32MP15xx platform currently comes with two incompatible implementations of
save_boot_params()weak function override. Factor thesave_boot_params()implementation into commoncpu.ccode and provide accessors to read out both ROM API table address and DT address from any place in the code instead.Signed-off-by Marek Vasut <[email protected]>---
Cc: Alexandru Gagniuc <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
---
V2: Avoid #if CONFIG... , use if (CONFIG... instead
V3: No change--- arch/arm/mach-stm32mp/boot_params.c | 20 ++--------- arch/arm/mach-stm32mp/cpu.c | 35 +++++++++++++++++++ arch/arm/mach-stm32mp/ecdsa_romapi.c | 20 ++--------- .../arm/mach-stm32mp/include/mach/sys_proto.h | 3 ++ 4 files changed, 42 insertions(+), 36 deletions(-)arch/arm/mach-stm32mp/boot_params.c +2
-18@@ -11,30 +11,14 @@#include <asm/sections.h> #include <asm/system.h> -/* -* Force data-section, as .bss will not be valid -* when save_boot_params is invoked. -*/ -static unsigned long nt_fw_dtb __section(".data"); - -/* -* Save the FDT address provided by TF-A in r2 at boot time -* This function is called from start.S -*/ -void save_boot_params (unsigned long r0,unsigned long r1,unsigned long r2, -unsigned long r3) -{ - nt_fw_dtb = r2; - -save_boot_params_ret (); -} -/* * Use the saved FDT address provided by TF-A at boot time (NT_FW_CONFIG = * Non Trusted Firmware configuration file) when the pointer is valid */ void *board_fdt_blob_setup (int *err) { +unsigned long nt_fw_dtb =get_stm32mp_bl2_dtb (); +log_debug ("%s: nt_fw_dtb=%lx\n" , __func__, nt_fw_dtb); *err =0 ;arch/arm/mach-stm32mp/cpu.c +35
-0@@ -378,3 +378,38 @@ int arch_misc_init(void)return 0 ; } + +/* +* Without forcing the ".data" section, this would get saved in ".bss". BSS +* will be cleared soon after, so it's not suitable. +*/ +static uintptr_t rom_api_table __section(".data"); +static uintptr_t nt_fw_dtb __section(".data"); + +/* +* The ROM gives us the API location in r0 when starting. This is only available +* during SPL, as there isn't (yet) a mechanism to pass this on to u-boot. Save +* the FDT address provided by TF-A in r2 at boot time. This function is called +* from start.S +*/ +void save_boot_params (unsigned long r0,unsigned long r1,unsigned long r2, +unsigned long r3) +{ +if (IS_ENABLED (CONFIG_STM32_ECDSA_VERIFY )) + rom_api_table = r0; + +if (IS_ENABLED (CONFIG_TFABOOT )) + nt_fw_dtb = r2; + +save_boot_params_ret (); +} + +uintptr_t get_stm32mp_rom_api_table (void ) +{ +return rom_api_table; +} + +uintptr_t get_stm32mp_bl2_dtb (void ) +{ +return nt_fw_dtb; +}arch/arm/mach-stm32mp/ecdsa_romapi.c +2
-18@@ -24,26 +24,10 @@ struct ecdsa_rom_api { uint32_t ecc_algo); }; -/* -* Without forcing the ".data" section, this would get saved in ".bss". BSS -* will be cleared soon after, so it's not suitable. -*/ -static uintptr_t rom_api_loc __section(".data"); - -/* -* The ROM gives us the API location in r0 when starting. This is only available -* during SPL, as there isn't (yet) a mechanism to pass this on to u-boot. -*/ -void save_boot_params (unsigned long r0,unsigned long r1,unsigned long r2, -unsigned long r3) -{ - rom_api_loc = r0; -save_boot_params_ret (); -} -static void stm32mp_rom_get_ecdsa_functions (struct ecdsa_rom_api *rom) { -uintptr_t verify_ptr = rom_api_loc +ROM_API_OFFSET_ECDSA_VERIFY ; +uintptr_t verify_ptr =get_stm32mp_rom_api_table () + +ROM_API_OFFSET_ECDSA_VERIFY ; rom->ecdsa_verify_signature = *(void **)verify_ptr; }arch/arm/mach-stm32mp/include/mach/sys_proto.h +0
-0arch/arm/mach-stm32mp/include/mach/sys_proto.h void stm32mp_misc_init(void); · line 82
Quoted 6 lines
arch/arm/mach-stm32mp/include/mach/sys_proto.h +3
-0@@ -77,3 +77,6 @@ void stm32mp_misc_init(void);/* helper function: read data from OTP */ u32 get_otp (int index,int shift,int mask); + +uintptr_t get_stm32mp_rom_api_table (void ); +uintptr_t get_stm32mp_bl2_dtb (void );Reviewed-by Patrice Chotard <[email protected]>Thanks
Patrice
Re: [PATCH v3 2/4] ARM: stm32: Factor out save_boot_params
Quoted 1 line · Patrice CHOTARD
Hi Marek
Hi,
Quoted 11 lines
I am preparing the next STM32 U-Boot pull request, during testing, buidlman is complaining with the following warning:
03: ARM: stm32: Factor out
save_boot_paramsarm: + stm32mp13
+../arch/arm/mach-stm32mp/boot_params.c: In function 'board_fdt_blob_setup':+../arch/arm/mach-stm32mp/boot_params.c:20:35: error: implicit declaration of function 'get_stm32mp_bl2_dtb' [-Werror=implicit-function-declaration](quoted diff) +3
-0+ 20 | unsigned long nt_fw_dtb = get_stm32mp_bl2_dtb(); + | ^~~~~~~~~~~~~~~~~~~ +cc1: all warnings being treated as errors
Quoted 1 line
Same issue with
stm32mp15_defconfigandstm32mp15_trusted_defconfig.
Sorry for the inconvenience.
Does the change below help ?
If so, can you squash it into 2/4 or do you want v4 ?
arch/arm/mach-stm32mp/boot_params.c +1 -0
@@ -8,6 +8,7 @@#include <common.h> #include <log.h> #include <linux/libfdt.h> +#include <asm/arch/sys_proto.h> #include <asm/sections.h> #include <asm/system.h>
Re: [PATCH v3 2/4] ARM: stm32: Factor out save_boot_params
Hi Marek
Quoted 16 lines · Marek Vasut
Quoted 1 line · Patrice CHOTARD
Hi Marek
Hi,
Quoted 11 lines
I am preparing the next STM32 U-Boot pull request, during testing, buidlman is complaining with the following warning:
03: ARM: stm32: Factor out
save_boot_params
arm: + stm32mp13+../arch/arm/mach-stm32mp/boot_params.c: In function 'board_fdt_blob_setup':+../arch/arm/mach-stm32mp/boot_params.c:20:35: error: implicit declaration of function 'get_stm32mp_bl2_dtb' [-Werror=implicit-function-declaration] + 20 | unsigned longnt_fw_dtb=get_stm32mp_bl2_dtb();
+ | ^~~~~~~~~~~~~~~~~~~
+cc1: all warnings being treated as errors
Quoted 6 lines
Quoted 1 line
Same issue with
stm32mp15_defconfigandstm32mp15_trusted_defconfig.Sorry for the inconvenience.
Does the change below help ?
If so, can you squash it into 2/4 or do you want v4 ?
Yes the change you proposed is OK.
I saw that you have submitted a v4 including this fix, i will add it to the next U-Boot STM32 PR.
Thanks for your reactivity ;-)
Patrice
Quoted 12 lines
arch/arm/mach-stm32mp/boot_params.c +1
-0@@ -8,6 +8,7 @@ #include <common.h> #include <log.h> #include <linux/libfdt.h> +#include <asm/arch/sys_proto.h> #include <asm/sections.h> #include <asm/system.h>
Re: [PATCH v3 2/4] ARM: stm32: Factor out save_boot_params
Quoted 1 line · Patrice CHOTARD
Hi Marek
Hello Patrice,
Quoted 19 lines · Marek Vasut
Quoted 18 lines · Patrice CHOTARD
Quoted 1 line
Hi Marek
Hi,
Quoted 12 lines
I am preparing the next STM32 U-Boot pull request, during testing, buidlman is complaining with the following warning:
03: ARM: stm32: Factor out
save_boot_params
arm: + stm32mp13+../arch/arm/mach-stm32mp/boot_params.c: In function 'board_fdt_blob_setup':+../arch/arm/mach-stm32mp/boot_params.c:20:35: error: implicit declaration of function 'get_stm32mp_bl2_dtb' [-Werror=implicit-function-declaration] + 20 | unsigned longnt_fw_dtb=get_stm32mp_bl2_dtb();
+ | ^~~~~~~~~~~~~~~~~~~
+cc1: all warnings being treated as errorsSame issue with
stm32mp15_defconfigandstm32mp15_trusted_defconfig.
Quoted 7 lines
Quoted 4 lines
Sorry for the inconvenience.
Does the change below help ?
If so, can you squash it into 2/4 or do you want v4 ?Yes the change you proposed is OK.
I saw that you have submitted a v4 including this fix, i will add it to the next U-Boot STM32 PR.
Thanks !
Quoted 1 line
Thanks for your reactivity ;-)
:)
PATCH v3 3/4 ARM: stm32: Pass ROM API table pointer to U-Boot proper
In reply to Marek VasutThe ROM API table pointer is no longer accessible from U-Boot, fix this by passing the ROM API pointer through. This makes it possible for U-Boot to call ROM API functions to authenticate payload like signed fitImages.
---
Cc: Alexandru Gagniuc <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
---
V2: - Rename image_entry_noargs_t to image_entry_stm32_t
- Add missing __noreturn
V3: No change
--- arch/arm/mach-stm32mp/cpu.c | 15 +++++++++++++++ 1 file changed, 15 insertions(+)
arch/arm/mach-stm32mp/cpu.c +15 -0
@@ -22,6 +22,7 @@#include <dm/device.h> #include <dm/uclass.h> #include <linux/bitops.h> +#include <spl.h> /* * early TLB into the .data section so that it not get cleared
@@ -413,3 +414,17 @@ uintptr_t get_stm32mp_bl2_dtb(void) {return nt_fw_dtb; } + +#ifdef CONFIG_SPL_BUILD +void __noreturn jump_to_image_no_args (struct spl_image_info *spl_image) +{ +typedef void __noreturn (*image_entry_stm32_t )(u32 romapi); +uintptr_t romapi =get_stm32mp_rom_api_table (); + +image_entry_stm32_t image_entry = + (image_entry_stm32_t )spl_image->entry_point; + +printf ("image entry point: 0x%lx\n" , spl_image->entry_point); +image_entry (romapi); +} +#endif
Signature · 1 line
2.35.1
Re: [PATCH v3 3/4] ARM: stm32: Pass ROM API table pointer to U-Boot proper
Hi,
Quoted 38 lines · Marek Vasut
The ROM API table pointer is no longer accessible from U-Boot, fix this by passing the ROM API pointer through. This makes it possible for U-Boot to call ROM API functions to authenticate payload like signed fitImages.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Alexandru Gagniuc <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
---
V2: - Renameimage_entry_noargs_ttoimage_entry_stm32_t
- Add missing__noreturn
V3: No change--- arch/arm/mach-stm32mp/cpu.c | 15 +++++++++++++++ 1 file changed, 15 insertions(+)arch/arm/mach-stm32mp/cpu.c +5
-0@@ -22,6 +22,7 @@#include <dm/device.h> #include <dm/uclass.h> #include <linux/bitops.h> +#include <spl.h> /* * early TLB into the .data section so that it not get cleared @@ -413,3 +414,17 @@ uintptr_t get_stm32mp_bl2_dtb(void) {return nt_fw_dtb; } + +#ifdef CONFIG_SPL_BUILD +void __noreturn jump_to_image_no_args (struct spl_image_info *spl_image) +{
arch/arm/mach-stm32mp/cpu.c uintptr_t get_stm32mp_bl2_dtb(void) · line 430
Quoted 10 lines
arch/arm/mach-stm32mp/cpu.c +10
-0+typedef void __noreturn (*image_entry_stm32_t )(u32 romapi); +uintptr_t romapi =get_stm32mp_rom_api_table (); + +image_entry_stm32_t image_entry = + (image_entry_stm32_t )spl_image->entry_point; + +printf ("image entry point: 0x%lx\n" , spl_image->entry_point); + image_entry(romapi); +} +#endif
Thanks
Patrick
Re: [PATCH v3 3/4] ARM: stm32: Pass ROM API table pointer to U-Boot proper
In reply to Marek VasutHi Marek
Quoted 38 lines · Marek Vasut
The ROM API table pointer is no longer accessible from U-Boot, fix this by passing the ROM API pointer through. This makes it possible for U-Boot to call ROM API functions to authenticate payload like signed fitImages.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Alexandru Gagniuc <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
---
V2: - Renameimage_entry_noargs_ttoimage_entry_stm32_t
- Add missing__noreturn
V3: No change--- arch/arm/mach-stm32mp/cpu.c | 15 +++++++++++++++ 1 file changed, 15 insertions(+)arch/arm/mach-stm32mp/cpu.c +5
-0@@ -22,6 +22,7 @@#include <dm/device.h> #include <dm/uclass.h> #include <linux/bitops.h> +#include <spl.h> /* * early TLB into the .data section so that it not get cleared @@ -413,3 +414,17 @@ uintptr_t get_stm32mp_bl2_dtb(void) {return nt_fw_dtb; } + +#ifdef CONFIG_SPL_BUILD +void __noreturn jump_to_image_no_args (struct spl_image_info *spl_image) +{
arch/arm/mach-stm32mp/cpu.c uintptr_t get_stm32mp_bl2_dtb(void) · line 430
Quoted 10 lines
arch/arm/mach-stm32mp/cpu.c +10
-0+typedef void __noreturn (*image_entry_stm32_t )(u32 romapi); +uintptr_t romapi =get_stm32mp_rom_api_table (); + +image_entry_stm32_t image_entry = + (image_entry_stm32_t )spl_image->entry_point; + +printf ("image entry point: 0x%lx\n" , spl_image->entry_point); + image_entry(romapi); +} +#endif
Thanks
Patrice
PATCH v3 4/4 ARM: stm32: Make ECDSA authentication available to U-Boot
In reply to Marek VasutWith U-Boot having access to ROM API call table, it is possible to use the ROM API call it authenticate e.g. signed kernel fitImages using the BootROM ECDSA support. Make this available by pulling the ECDSA BootROM call support from SPL-only guard.
---
Cc: Alexandru Gagniuc <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
---
V2: Add RB from Patrice and Patrick
V3: No change
--- arch/arm/mach-stm32mp/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-stm32mp/Makefile +1 -1
@@ -11,10 +11,10 @@ obj-y += bsec.o obj-$(CONFIG_STM32MP13x) += stm32mp13x.o obj-$(CONFIG_STM32MP15x) += stm32mp15x.o +obj-$(CONFIG_STM32_ECDSA_VERIFY) += ecdsa_romapi.o ifdef CONFIG_SPL_BUILD obj-y += spl.o obj-y += tzc400.o -obj-$(CONFIG_STM32_ECDSA_VERIFY) += ecdsa_romapi.o else obj-y += cmd_stm32prog/ obj-$(CONFIG_CMD_STM32KEY) += cmd_stm32key.o
Signature · 1 line
2.35.1
Hi,
Quoted 23 lines · Marek Vasut
In case Dcache is enabled while the ECDSA authentication function is called via BootROM ROM API, the MMU tables are set up and the BootROM region is not marked as executable, so an attempt to run code from it results in a hang. Mark the BootROM region as executable as suggested by Patrick to prevent the hang.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Alexandru Gagniuc <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
---
V2: - Initializereenable_dcachevariable
V3: - Mark BootROM as executable instead--- arch/arm/mach-stm32mp/ecdsa_romapi.c | 4 ++++ 1 file changed, 4 insertions(+)arch/arm/mach-stm32mp/ecdsa_romapi.c +0
-0
arch/arm/mach-stm32mp/ecdsa_romapi.c static int romapi_ecdsa_verify(struct udevice *dev, · line 90
Quoted 10 lines
arch/arm/mach-stm32mp/ecdsa_romapi.c +4
-0@@ -81,6 +81,10 @@ static int romapi_ecdsa_verify(struct udevice *dev,memcpy (raw_key +32 , pubkey->y,32 );stm32mp_rom_get_ecdsa_functions (&rom); + +/* Mark BootROM region as executable. */ +mmu_set_region_dcache_behaviour (0 ,SZ_2M ,DCACHE_DEFAULT_OPTION ); + rom_ret = rom.ecdsa_verify_signature (hash, raw_key, signature, algo);return rom_ret ==ROM_API_SUCCESS ?0 : -EPERM ;
Thanks
Patrick
Hi Marek
Quoted 23 lines · Marek Vasut
In case Dcache is enabled while the ECDSA authentication function is called via BootROM ROM API, the MMU tables are set up and the BootROM region is not marked as executable, so an attempt to run code from it results in a hang. Mark the BootROM region as executable as suggested by Patrick to prevent the hang.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Alexandru Gagniuc <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
---
V2: - Initializereenable_dcachevariable
V3: - Mark BootROM as executable instead--- arch/arm/mach-stm32mp/ecdsa_romapi.c | 4 ++++ 1 file changed, 4 insertions(+)arch/arm/mach-stm32mp/ecdsa_romapi.c +0
-0
arch/arm/mach-stm32mp/ecdsa_romapi.c static int romapi_ecdsa_verify(struct udevice *dev, · line 90
Quoted 10 lines
arch/arm/mach-stm32mp/ecdsa_romapi.c +4
-0@@ -81,6 +81,10 @@ static int romapi_ecdsa_verify(struct udevice *dev,memcpy (raw_key +32 , pubkey->y,32 );stm32mp_rom_get_ecdsa_functions (&rom); + +/* Mark BootROM region as executable. */ +mmu_set_region_dcache_behaviour (0 ,SZ_2M ,DCACHE_DEFAULT_OPTION ); + rom_ret = rom.ecdsa_verify_signature (hash, raw_key, signature, algo);return rom_ret ==ROM_API_SUCCESS ?0 : -EPERM ;
Thanks
Patrice