drivers: spi: fix some typos and change a printf() to log_warning
Subsystems (6)
v2 cover drivers: spi: fix some typos and change a printf() to log_warning
From v1 to v2, the printf() in drivers/spi/sh_qspi.c was changed to log_warning(). Which avoids using __func__ to output driver information.
Pengfei Fan (2):
drivers: spi: fix some typos
drivers: spi: sh_qspi.c: Use log_warning() instead of printf()
drivers/spi/bcm63xx_hsspi.c | 2 +- drivers/spi/cadence_qspi.c | 2 +- drivers/spi/fsl_dspi.c | 4 ++-- drivers/spi/mtk_snfi_spi.c | 4 ++-- drivers/spi/mvebu_a3700_spi.c | 2 +- drivers/spi/omap3_spi.c | 2 +- drivers/spi/rk_spi.c | 2 +- drivers/spi/sh_qspi.c | 4 +++- drivers/spi/spi-aspeed-smc.c | 4 ++-- drivers/spi/spi-qup.c | 2 +- drivers/spi/spi-sifive.c | 2 +- 11 files changed, 16 insertions(+), 14 deletions(-)
Signature · 1 line
2.31.1.windows.1
PATCH v2 1/2 drivers: spi: fix some typos
Fix some typos in spi drivers
Signed-off-by Pengfei Fan <[email protected]>
Reviewed-by Simon Glass <[email protected]>
--- drivers/spi/bcm63xx_hsspi.c | 2 +- drivers/spi/cadence_qspi.c | 2 +- drivers/spi/fsl_dspi.c | 4 ++-- drivers/spi/mtk_snfi_spi.c | 4 ++-- drivers/spi/mvebu_a3700_spi.c | 2 +- drivers/spi/omap3_spi.c | 2 +- drivers/spi/rk_spi.c | 2 +- drivers/spi/spi-aspeed-smc.c | 4 ++-- drivers/spi/spi-qup.c | 2 +- drivers/spi/spi-sifive.c | 2 +- 10 files changed, 13 insertions(+), 13 deletions(-)
drivers/spi/bcm63xx_hsspi.c +1 -1
@@ -210,7 +210,7 @@ static void bcm63xx_hsspi_deactivate_cs(struct bcm63xx_hsspi_priv *priv)* claimed. This way, the dummy CS is restored to its inactive value when * transfers are issued and the desired CS is preserved in its active value * all the time. This hack is also used in the upstream linux driver and -* allows keeping CS active between trasnfers even if the HW doesn't give +* allows keeping CS active between transfers even if the HW doesn't give * this possibility. */ static int bcm63xx_hsspi_xfer(struct udevice *dev, unsigned int bitlen,
drivers/spi/cadence_qspi.c +1 -1
@@ -392,7 +392,7 @@ static int cadence_spi_of_to_plat(struct udevice *bus) plat->is_dma =dev_read_bool (bus,"cdns,is-dma" ); -/* All other paramters are embedded in the child node */ +/* All other parameters are embedded in the child node */ subnode =dev_read_first_subnode (bus);if (!ofnode_valid (subnode)) {printf ("Error: subnode with SPI flash config missing!\n" );
drivers/spi/fsl_dspi.c +2 -2
@@ -491,7 +491,7 @@ static int fsl_dspi_probe(struct udevice *bus) dm_spi_bus =dev_get_uclass_priv (bus); -/* cpu speical pin muxing configure */ +/* cpu special pin muxing configure */ cpu_dspi_port_conf ();/* get input clk frequency */
@@ -600,7 +600,7 @@ static int fsl_dspi_of_to_plat(struct udevice *bus) plat->speed_hz =fdtdec_get_int (blob, node,"spi-max-frequency" ,FSL_DSPI_DEFAULT_SCK_FREQ ); -debug ("DSPI: regs=%pa, max-frequency=%d, endianess=%s, num-cs=%d\n" , +debug ("DSPI: regs=%pa, max-frequency=%d, endianness=%s, num-cs=%d\n" , &plat->regs_addr, plat->speed_hz, plat->flags &DSPI_FLAG_REGMAP_ENDIAN_BIG ?"be" :"le" , plat->num_chipselect);
drivers/spi/mtk_snfi_spi.c +2 -2
@@ -153,7 +153,7 @@ static void mtk_snfi_copy_to_gpram(struct mtk_snfi_priv *priv,/* * The output data will always be copied to the beginning of -* the GPRAM. Uses word write for better performace. +* the GPRAM. Uses word write for better performance. * * Trailing bytes in the last word are not cared. */
@@ -180,7 +180,7 @@ static void mtk_snfi_copy_from_gpram(struct mtk_snfi_priv *priv, u8 *cache,/* * Read aligned data from GPRAM to buffer first. -* Uses word read for better performace. +* Uses word read for better performance. */ i =0 ;while (pos < end) {
drivers/spi/mvebu_a3700_spi.c +1 -1
@@ -84,7 +84,7 @@ static void spi_cs_deactivate(struct mvebu_spi_plat *plat, int cs)* The XFER_RDY flag is checked every time before accessing SPI_DOUT * and SPI_DIN register. * -* The number of transfers to be triggerred is decided by @bytelen. +* The number of transfers to be triggered is decided by @bytelen. * * Return: 0 - cool * -ETIMEDOUT - XFER_RDY flag timeout
drivers/spi/omap3_spi.c +1 -1
@@ -142,7 +142,7 @@ static int omap3_spi_read(struct omap3_spi_priv *priv, unsigned int len, } } -/* Disable the channel to prevent furher receiving */ +/* Disable the channel to prevent further receiving */ if (i == (len -1 ))omap3_spi_set_enable (priv,OMAP3_MCSPI_CHCTRL_DIS );
drivers/spi/rk_spi.c +1 -1
@@ -485,7 +485,7 @@ static int rockchip_spi_xfer(struct udevice *dev, unsigned int bitlen,/* * In case that there's a transmit-component, we need to wait * until the control goes idle before we can disable the SPI -* control logic (as this will implictly flush the FIFOs). +* control logic (as this will implicitly flush the FIFOs). */ if (out) { ret =rkspi_wait_till_not_busy (regs);
drivers/spi/spi-aspeed-smc.c +2 -2
@@ -270,7 +270,7 @@ static int ast2500_adjust_decoded_size(struct udevice *bus) flashes[cs].ahb_decoded_sz = priv->info->min_decoded_sz;/* -* If commnad mode or normal mode is used, the start address of a +* If command mode or normal mode is used, the start address of a * decoded range should be multiple of its related flash size. * Namely, the total decoded size from flash 0 to flash N should * be multiple of the size of flash (N + 1).
@@ -404,7 +404,7 @@ static int ast2600_adjust_decoded_size(struct udevice *bus) flashes[cs].ahb_decoded_sz =0 ;/* -* If commnad mode or normal mode is used, the start address of a +* If command mode or normal mode is used, the start address of a * decoded range should be multiple of its related flash size. * Namely, the total decoded size from flash 0 to flash N should * be multiple of the size of flash (N + 1).
drivers/spi/spi-qup.c +1 -1
@@ -233,7 +233,7 @@ static unsigned char qup_spi_read_byte(struct udevice *dev) }/* -* Function to check wheather Input or Output FIFO +* Function to check whether Input or Output FIFO * has data to be serviced */ static int qup_spi_check_fifo_status (struct udevice *dev,u32 reg_addr)
drivers/spi/spi-sifive.c +1 -1
@@ -350,7 +350,7 @@ static int sifive_spi_set_speed(struct udevice *bus, uint speed)if (speed > spi->freq) speed = spi->freq; -/* Cofigure max speed */ +/* Configure max speed */ scale = (DIV_ROUND_UP (spi->freq >>1 , speed) -1 ) &SIFIVE_SPI_SCKDIV_DIV_MASK ;writel (scale, spi->regs +SIFIVE_SPI_REG_SCKDIV );
Signature · 1 line
2.31.1.windows.1
PATCH v2 2/2 drivers: spi: sh_qspi.c: Use log_warning() instead of printf()
In reply to Pengfei FanUse log_warning() instead of printf() to print out driver information
Signed-off-by Pengfei Fan <[email protected]>
Reviewed-by Simon Glass <[email protected]>
--- drivers/spi/sh_qspi.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/spi/sh_qspi.c +3 -1
@@ -6,6 +6,8 @@* Copyright (C) 2013 Nobuhiro Iwamatsu <[email protected]> */ +#define LOG_CATEGORY UCLASS_SPI +#include <common.h> #include <console.h> #include <malloc.h>
@@ -160,7 +162,7 @@ static int sh_qspi_xfer_common(struct sh_qspi_slave *ss, unsigned int bitlen, }if (bitlen %8 ) { -printf ("%s: bitlen is not 8bit alined %d" , __func__, bitlen); +log_warning ("bitlen is not 8bit aligned %d" , bitlen);return 1 ; }
Signature · 1 line
2.31.1.windows.1
Re: [PATCH v2 2/2] drivers: spi: sh_qspi.c: Use log_warning() instead of printf()
Quoted 6 lines · Pengfei Fan
Use
log_warning()instead ofprintf()to print out driver informationSigned-off-by Pengfei Fan <[email protected]>Reviewed-by Simon Glass <[email protected]>---
Applied both to u-boot-spi/master