Skip to contentSkip to conversation

PWM and keyboard backlight driver for ARM Macs

PATCH Superseded Sasha Finkelstein 3 participants 10 messages Jan 6, 2023 – Jan 13, 2023

Subsystems (3)

v6 of 9 Superseded Latest is v9 →

lore
Share & tools
lore
#0 lore raw

v6 cover PWM and keyboard backlight driver for ARM Macs

Hi,

This is the v6 of the patch series to add PWM and keyboard backlight driver for ARM macs. This time the changes are a bit more substantial and include the changes to the t600x (M1 Pro/Max) device trees.

Here is hoping that this time, the paint on this shed is up to everyone's standards.

Changes in v1:
Addressing the review comments.

Changes in v2:
Added the reviewed-by and acked-by tags.
Addressing a review comment.

Changes in v3 and v4:
Addressing the review comments.

Changes in v5:
Added t600x device tree changes

v1: https://www.spinics.net/lists/linux-pwm/msg19500.html
v2: https://www.spinics.net/lists/linux-pwm/msg19562.html
v3: https://www.spinics.net/lists/linux-pwm/msg19901.html
v4: https://www.spinics.net/lists/linux-pwm/msg20093.html
v5: https://www.spinics.net/lists/linux-pwm/msg20150.html

Sasha Finkelstein (5):
dt-bindings: pwm: Add Apple PWM controller
pwm: Add Apple PWM controller
arm64: dts: apple: t8103: Add PWM controller
arm64: dts: apple: t600x: Add PWM controller
MAINTAINERS: Add entries for Apple PWM driver

 .../bindings/pwm/apple,s5l-fpwm.yaml          |  51 ++++++
 MAINTAINERS                                   |   2 +
 arch/arm64/boot/dts/apple/t600x-die0.dtsi     |   9 +
 .../arm64/boot/dts/apple/t600x-j314-j316.dtsi |  18 ++
 arch/arm64/boot/dts/apple/t8103-j293.dts      |  17 ++
 arch/arm64/boot/dts/apple/t8103-j313.dts      |  17 ++
 arch/arm64/boot/dts/apple/t8103.dtsi          |   9 +
 drivers/pwm/Kconfig                           |  12 ++
 drivers/pwm/Makefile                          |   1 +
 drivers/pwm/pwm-apple.c                       | 156 ++++++++++++++++++
 10 files changed, 292 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pwm/apple,s5l-fpwm.yaml
 create mode 100644 drivers/pwm/pwm-apple.c
Signature · 1 line
2.37.1 (Apple Git-137.1)
#1 lore raw

PATCH v6 1/5 dt-bindings: pwm: Add Apple PWM controller

Apple SoCs such as the M1 contain a PWM controller used among other things to control the keyboard backlight.

---
 .../bindings/pwm/apple,s5l-fpwm.yaml          | 51 +++++++++++++++++++
 1 file changed, 51 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pwm/apple,s5l-fpwm.yaml
Documentation/devicetree/bindings/pwm/apple,s5l-fpwm.yaml new file +51 -0
new file mode 100644
index 000000000000..142157bff0cd
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pwm/apple,s5l-fpwm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Apple FPWM controller
+
+maintainers:
+  - [email protected]
+  - Sasha Finkelstein <[email protected]>
+
+description: PWM controller used for keyboard backlight on ARM Macs
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - apple,t8103-fpwm
+          - apple,t6000-fpwm
+          - apple,t8112-fpwm
+      - const: apple,s5l-fpwm
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  "#pwm-cells":
+    const: 2
+
+required:
+  - compatible
+  - reg
+  - clocks
+
+additionalProperties: false
+
+examples:
+  - |
+    pwm@235044000 {
+      compatible = "apple,t8103-fpwm", "apple,s5l-fpwm";
+      reg = <0x35044000 0x4000>;
+      power-domains = <&ps_fpwm1>;
+      clocks = <&clkref>;
+      #pwm-cells = <2>;
+    };
Signature · 1 line
2.37.1 (Apple Git-137.1)
#2 lore raw

PATCH v6 2/5 pwm: Add Apple PWM controller

In reply to Sasha Finkelstein

Adds the Apple PWM controller driver.

---
 drivers/pwm/Kconfig     |  12 ++++
 drivers/pwm/Makefile    |   1 +
 drivers/pwm/pwm-apple.c | 156 ++++++++++++++++++++++++++++++++++++++++
 3 files changed, 169 insertions(+)
 create mode 100644 drivers/pwm/pwm-apple.c
drivers/pwm/Kconfig +12 -0
index dae023d783a2..8df861b1f4a3 100644
@@ -51,6 +51,18 @@ config PWM_AB8500
 	  To compile this driver as a module, choose M here: the module
 	  will be called pwm-ab8500.
 
+config PWM_APPLE
+	tristate "Apple SoC PWM support"
+	depends on ARCH_APPLE || COMPILE_TEST
+	help
+	  Generic PWM framework driver for PWM controller present on
+	  Apple SoCs
+
+	  Say Y here if you have an ARM Apple laptop, otherwise say N
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called pwm-apple.
+
 config PWM_ATMEL
 	tristate "Atmel PWM support"
 	depends on ARCH_AT91 || COMPILE_TEST
drivers/pwm/Makefile +1 -0
index 7bf1a29f02b8..19899b912e00 100644
@@ -2,6 +2,7 @@
 obj-$(CONFIG_PWM)		+= core.o
 obj-$(CONFIG_PWM_SYSFS)		+= sysfs.o
 obj-$(CONFIG_PWM_AB8500)	+= pwm-ab8500.o
+obj-$(CONFIG_PWM_APPLE)		+= pwm-apple.o
 obj-$(CONFIG_PWM_ATMEL)		+= pwm-atmel.o
 obj-$(CONFIG_PWM_ATMEL_HLCDC_PWM)	+= pwm-atmel-hlcdc.o
 obj-$(CONFIG_PWM_ATMEL_TCB)	+= pwm-atmel-tcb.o
drivers/pwm/pwm-apple.c new file +156 -0

156 lines not on this page · raw message

Signature · 1 line
2.37.1 (Apple Git-137.1)
#3 lore raw

Re: [PATCH v6 2/5] pwm: Add Apple PWM controller

Hello Sasha,

Quoted 53 lines · Sasha Finkelstein

Adds the Apple PWM controller driver.

---
 drivers/pwm/Kconfig     |  12 ++++
 drivers/pwm/Makefile    |   1 +
 drivers/pwm/pwm-apple.c | 156 ++++++++++++++++++++++++++++++++++++++++
 3 files changed, 169 insertions(+)
 create mode 100644 drivers/pwm/pwm-apple.c
drivers/pwm/Kconfig +12 -0
index dae023d783a2..8df861b1f4a3 100644
@@ -51,6 +51,18 @@ config PWM_AB8500
 	  To compile this driver as a module, choose M here: the module
 	  will be called pwm-ab8500.
 
+config PWM_APPLE
+	tristate "Apple SoC PWM support"
+	depends on ARCH_APPLE || COMPILE_TEST
+	help
+	  Generic PWM framework driver for PWM controller present on
+	  Apple SoCs
+
+	  Say Y here if you have an ARM Apple laptop, otherwise say N
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called pwm-apple.
+
 config PWM_ATMEL
 	tristate "Atmel PWM support"
 	depends on ARCH_AT91 || COMPILE_TEST
drivers/pwm/Makefile +1 -0
index 7bf1a29f02b8..19899b912e00 100644
@@ -2,6 +2,7 @@
 obj-$(CONFIG_PWM)		+= core.o
 obj-$(CONFIG_PWM_SYSFS)		+= sysfs.o
 obj-$(CONFIG_PWM_AB8500)	+= pwm-ab8500.o
+obj-$(CONFIG_PWM_APPLE)		+= pwm-apple.o
 obj-$(CONFIG_PWM_ATMEL)		+= pwm-atmel.o
 obj-$(CONFIG_PWM_ATMEL_HLCDC_PWM)	+= pwm-atmel-hlcdc.o
 obj-$(CONFIG_PWM_ATMEL_TCB)	+= pwm-atmel-tcb.o
drivers/pwm/pwm-apple.c new file +1 -0
new file mode 100644
index 000000000000..5360583a5fa6
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT

drivers/pwm/pwm-apple.c line 11

Quoted 10 lines
drivers/pwm/pwm-apple.c new file +10 -0
+/*
+ * Driver for the Apple SoC PWM controller
+ *
+ * Copyright The Asahi Linux Contributors
+ *
+ * Limitations:
+ * - The writes to cycle registers are shadowed until a write to
+ *   the control register.
+ * - If both OFF_CYCLES and ON_CYCLES are set to 0, the output
+ *   is a constant off signal.

How does the PWM behave with *APPLE_PWM_CTRLAPPLE_PWM_CTRL = 0? (typically: drives constant low)

Quoted 9 lines
drivers/pwm/pwm-apple.c new file +9 -0
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/math64.h>
+

drivers/pwm/pwm-apple.c line 30

Quoted 10 lines
drivers/pwm/pwm-apple.c new file +10 -0
+#define APPLE_PWM_CTRL        0x00
+#define APPLE_PWM_ON_CYCLES   0x1c
+#define APPLE_PWM_OFF_CYCLES  0x18
+
+#define APPLE_CTRL_ENABLE        BIT(0)
+#define APPLE_CTRL_MODE          BIT(2)
+#define APPLE_CTRL_UPDATE        BIT(5)
+#define APPLE_CTRL_TRIGGER       BIT(9)
+#define APPLE_CTRL_INVERT        BIT(10)
+#define APPLE_CTRL_OUTPUT_ENABLE BIT(14)

In reply to v4 I wrote:

| Would be nice if the register prefix would match the register name. That
| is please either rename APPLE_PWM_CONTROL to APPLE_PWM_CTRL or use
| APPLE_PWM_CONTROL as prefix for the bit fields in that register.

well, one of the two options was bogus because it doesn't result in the intended effect. You picked that broken option :-\
Can you please rename such that the (maybe new) name for APPLE_PWM_CTRL is a prefix for the (maybe new) APPLE_CTRL_ENABLE and the other register bit definitions?

Quoted 4 lines

[...]

drivers/pwm/pwm-apple.c new file +3 -0
+static int apple_pwm_probe(struct platform_device *pdev)
+{
+	struct apple_pwm *fpwm;

drivers/pwm/pwm-apple.c line 115

Quoted 10 lines
drivers/pwm/pwm-apple.c new file +10 -0
+	struct clk *clk;
+	int ret;
+
+	fpwm = devm_kzalloc(&pdev->dev, sizeof(*fpwm), GFP_KERNEL);
+	if (!fpwm)
+		return -ENOMEM;
+
+	fpwm->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(fpwm->base))
+		return dev_err_probe(&pdev->dev, PTR_ERR(fpwm->base), "unable to map mmio");

devm_platform_ioremap_resource() already emits an error message if there is a problem. So please don't add another message here.

drivers/pwm/pwm-apple.c line 127

Quoted 11 lines
drivers/pwm/pwm-apple.c new file +11 -0
+	clk = devm_clk_get_enabled(&pdev->dev, NULL);
+	if (IS_ERR(clk))
+		return dev_err_probe(&pdev->dev, PTR_ERR(clk), "unable to get the clock");
+
+	/*
+	 * uses the 24MHz system clock on all existing devices, can only
+	 * happen if the device tree is broken
+	 */
+	fpwm->clkrate = clk_get_rate(clk);
+	if (fpwm->clkrate > NSEC_PER_SEC)
+		return dev_err_probe(&pdev->dev, -EINVAL, "pwm clock out of range");

This check is done to prevent an overflow in .apply, right? Please point that out in a comment.

drivers/pwm/pwm-apple.c line 139

Quoted 12 lines
drivers/pwm/pwm-apple.c new file +11 -0
+	fpwm->chip.dev = &pdev->dev;
+	fpwm->chip.npwm = 1;
+	fpwm->chip.ops = &apple_pwm_ops;
+
+	ret = devm_pwmchip_add(&pdev->dev, &fpwm->chip);
+	if (ret < 0)
+		return dev_err_probe(&pdev->dev, ret, "unable to add pwm chip");
+
+	return 0;
+}
+
[...]

Best regards
Uwe

Signature · 2 lines
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |
#4 lore raw

Re: [PATCH v6 2/5] pwm: Add Apple PWM controller

Quoted 9 lines · Uwe Kleine-König
Quoted 5 lines

+ * Limitations:
+ * - The writes to cycle registers are shadowed until a write to
+ * the control register.
+ * - If both OFF_CYCLES and ON_CYCLES are set to 0, the output
+ * is a constant off signal.

How does the PWM behave with *APPLE_PWM_CTRLAPPLE_PWM_CTRL = 0? (typically: drives constant low)

APPLE_PWM_CTRL = 0 implies that the APPLE_CTRL_ENABLE bit is set low, which turns off the pwm signal (constant low). I do not think that it is necessary to explicitly
specify that case in the comments.

Quoted 3 lines

Can you please rename such that the (maybe new) name for APPLE_PWM_CTRL is a prefix for the (maybe new) APPLE_CTRL_ENABLE and the other register bit definitions?

To make sure, you want the register named APPLE_PWM_CTRL, and the bits named APPLE_PWM_CTRL_ENABLE, APPLE_PWM_CTRL_MODE and so on?

#5 lore raw

Re: [PATCH v6 2/5] pwm: Add Apple PWM controller

Quoted 8 lines · Sasha Finkelstein
Quoted 6 lines · Uwe Kleine-König
Quoted 5 lines

+ * Limitations:
+ * - The writes to cycle registers are shadowed until a write to
+ * the control register.
+ * - If both OFF_CYCLES and ON_CYCLES are set to 0, the output
+ * is a constant off signal.

Quoted 7 lines
Quoted 3 lines

How does the PWM behave with *APPLE_PWM_CTRLAPPLE_PWM_CTRL = 0? (typically: drives constant low)

APPLE_PWM_CTRL = 0 implies that the APPLE_CTRL_ENABLE bit is set low, which turns off the pwm signal (constant low). I do not think that it is necessary to explicitly
specify that case in the comments.

This is an information that I want to have available. Ideally easily greppable by using the format that other drivers use for that, too. (The command I usually use is:

	sed -rn '/Limitations:/,/\*\/?$/p' drivers/pwm/*.c

so if you make sure your info is added accordingly that would be good.)

This is useful to answer questions like: Can I reasonably expect that a disabled PWM respects the configured polarity.

Quoted 5 lines
Quoted 3 lines

Can you please rename such that the (maybe new) name for APPLE_PWM_CTRL is a prefix for the (maybe new) APPLE_CTRL_ENABLE and the other register bit definitions?

To make sure, you want the register named APPLE_PWM_CTRL, and the bits named APPLE_PWM_CTRL_ENABLE, APPLE_PWM_CTRL_MODE and so on?

Yes.

Best regards
Uwe

Signature · 2 lines
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |
#6 lore raw

PATCH v6 3/5 arm64: dts: apple: t8103: Add PWM controller

In reply to Sasha Finkelstein

Adds PWM controller and keyboard backlight bindings for M1 MacBooks

---
 arch/arm64/boot/dts/apple/t8103-j293.dts | 17 +++++++++++++++++
 arch/arm64/boot/dts/apple/t8103-j313.dts | 17 +++++++++++++++++
 arch/arm64/boot/dts/apple/t8103.dtsi     |  9 +++++++++
 3 files changed, 43 insertions(+)
arch/arm64/boot/dts/apple/t8103-j293.dts +17 -0
index 151074109a11..7381dccc1613 100644
@@ -11,10 +11,23 @@
 
 #include "t8103.dtsi"
 #include "t8103-jxxx.dtsi"
+#include <dt-bindings/leds/common.h>
 
 / {
 	compatible = "apple,j293", "apple,t8103", "apple,arm-platform";
 	model = "Apple MacBook Pro (13-inch, M1, 2020)";
+
+	led-controller {
+		compatible = "pwm-leds";
+		led-0 {
+			pwms = <&fpwm1 0 40000>;
+			label = "kbd_backlight";
+			function = LED_FUNCTION_KBD_BACKLIGHT;
+			color = <LED_COLOR_ID_WHITE>;
+			max-brightness = <255>;
+			default-state = "keep";
+		};
+	};
 };
 
 &bluetooth0 {
@@ -47,3 +60,7 @@ &i2c2 {
 &i2c4 {
 	status = "okay";
 };
+
+&fpwm1 {
+	status = "okay";
+};
\ No newline at end of file
arch/arm64/boot/dts/apple/t8103-j313.dts +17 -0
index bc1f865aa790..1e26aa1ef525 100644
@@ -11,10 +11,23 @@
 
 #include "t8103.dtsi"
 #include "t8103-jxxx.dtsi"
+#include <dt-bindings/leds/common.h>
 
 / {
 	compatible = "apple,j313", "apple,t8103", "apple,arm-platform";
 	model = "Apple MacBook Air (M1, 2020)";
+
+	led-controller {
+		compatible = "pwm-leds";
+		led-0 {
+			pwms = <&fpwm1 0 40000>;
+			label = "kbd_backlight";
+			function = LED_FUNCTION_KBD_BACKLIGHT;
+			color = <LED_COLOR_ID_WHITE>;
+			max-brightness = <255>;
+			default-state = "keep";
+		};
+	};
 };
 
 &bluetooth0 {
@@ -39,3 +52,7 @@ &pcie0_dart_2 {
 
 /delete-node/ &port01;
 /delete-node/ &port02;
+
+&fpwm1 {
+	status = "okay";
+};
arch/arm64/boot/dts/apple/t8103.dtsi +9 -0
index 9859219699f4..5300fd115561 100644
@@ -432,6 +432,15 @@ i2c4: i2c@235020000 {
 			status = "disabled"; /* only used in J293 */
 		};
 
+		fpwm1: pwm@235044000 {
+			compatible = "apple,t8103-fpwm", "apple,s5l-fpwm";
+			reg = <0x2 0x35044000 0x0 0x4000>;
+			power-domains = <&ps_fpwm1>;
+			clocks = <&clkref>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
 		serial0: serial@235200000 {
 			compatible = "apple,s5l-uart";
 			reg = <0x2 0x35200000 0x0 0x1000>;
Signature · 1 line
2.37.1 (Apple Git-137.1)
#7 lore raw

PATCH v6 4/5 arm64: dts: apple: t600x: Add PWM controller

In reply to Sasha Finkelstein

Adds PWM controller and keyboard backlight bindings for M1 Pro/Max MacBook Pros

---
 arch/arm64/boot/dts/apple/t600x-die0.dtsi      |  9 +++++++++
 arch/arm64/boot/dts/apple/t600x-j314-j316.dtsi | 18 ++++++++++++++++++
 2 files changed, 27 insertions(+)
arch/arm64/boot/dts/apple/t600x-die0.dtsi +9 -0
index 1c41954e3899..7065045dc43a 100644
@@ -154,6 +154,15 @@ i2c5: i2c@39b054000 {
 		status = "disabled";
 	};
 
+	fpwm0: pwm@39b030000 {
+		compatible = "apple,t6000-fpwm", "apple,s5l-fpwm";
+		reg = <0x3 0x9b030000 0x0 0x4000>;
+		power-domains = <&ps_fpwm0>;
+		clocks = <&clkref>;
+		#pwm-cells = <2>;
+		status = "disabled";
+	};
+
 	serial0: serial@39b200000 {
 		compatible = "apple,s5l-uart";
 		reg = <0x3 0x9b200000 0x0 0x1000>;
arch/arm64/boot/dts/apple/t600x-j314-j316.dtsi +18 -0
index 34906d522f0a..96de7165df6d 100644
@@ -9,6 +9,8 @@
  * Copyright The Asahi Linux Contributors
  */
 
+#include <dt-bindings/leds/common.h>
+
 / {
 	aliases {
 		serial0 = &serial0;
@@ -34,6 +36,18 @@ memory@10000000000 {
 		device_type = "memory";
 		reg = <0x100 0 0x2 0>; /* To be filled by loader */
 	};
+
+	led-controller {
+		compatible = "pwm-leds";
+		led-0 {
+			pwms = <&fpwm0 0 40000>;
+			label = "kbd_backlight";
+			function = LED_FUNCTION_KBD_BACKLIGHT;
+			color = <LED_COLOR_ID_WHITE>;
+			max-brightness = <255>;
+			default-state = "keep";
+		};
+	};
 };
 
 &serial0 {
@@ -110,5 +124,9 @@ &pcie0_dart_3 {
 	status = "disabled";
 };
 
+&fpwm0 {
+	status = "okay";
+};
+
 /delete-node/ &port02;
 /delete-node/ &port03;
Signature · 1 line
2.37.1 (Apple Git-137.1)
Acked-by on v6 4/5
#8 lore raw

Re: [PATCH v6 4/5] arm64: dts: apple: t600x: Add PWM controller

Quoted 15 lines · Sasha Finkelstein

Adds PWM controller and keyboard backlight bindings for M1 Pro/Max MacBook Pros

---
 arch/arm64/boot/dts/apple/t600x-die0.dtsi      |  9 +++++++++
 arch/arm64/boot/dts/apple/t600x-j314-j316.dtsi | 18 ++++++++++++++++++
 2 files changed, 27 insertions(+)
arch/arm64/boot/dts/apple/t600x-die0.dtsi +0 -0
index 1c41954e3899..7065045dc43a 100644
@@ -154,6 +154,15 @@ i2c5: i2c@39b054000 {
 		status = "disabled";
 	};

arch/arm64/boot/dts/apple/t600x-die0.dtsi i2c5: i2c@39b054000 { · line 165

Quoted 10 lines
arch/arm64/boot/dts/apple/t600x-die0.dtsi +9 -0
 
+	fpwm0: pwm@39b030000 {
+		compatible = "apple,t6000-fpwm", "apple,s5l-fpwm";
+		reg = <0x3 0x9b030000 0x0 0x4000>;
+		power-domains = <&ps_fpwm0>;
+		clocks = <&clkref>;
+		#pwm-cells = <2>;
+		status = "disabled";
+	};
+

We usually keep device nodes sorted by address, so this is out of order and should come before i2c (at least). No need to respin just for this though, I can fix it when I apply it, so:

Maintainers: as we usually ask, please merge only the driver commit (#2) via the PWM tree, we'll take care of DTs/MAINTAINERS/bindings via asahi-soc so we can avoid serializing/blocking other DT changes.

- Hector

#9 lore raw

PATCH v6 5/5 MAINTAINERS: Add entries for Apple PWM driver

In reply to Sasha Finkelstein

Add the MAINTAINERS entries for the driver

---
 MAINTAINERS | 2 ++
 1 file changed, 2 insertions(+)
MAINTAINERS +2 -0
index 7f86d02cb427..75bda5ab704d 100644
@@ -1970,6 +1970,7 @@ F:	Documentation/devicetree/bindings/nvmem/apple,efuses.yaml
 F:	Documentation/devicetree/bindings/pci/apple,pcie.yaml
 F:	Documentation/devicetree/bindings/pinctrl/apple,pinctrl.yaml
 F:	Documentation/devicetree/bindings/power/apple*
+F:	Documentation/devicetree/bindings/pwm/pwm-apple.yaml
 F:	Documentation/devicetree/bindings/watchdog/apple,wdt.yaml
 F:	arch/arm64/boot/dts/apple/
 F:	drivers/bluetooth/hci_bcm4377.c
@@ -1985,6 +1986,7 @@ F:	drivers/mailbox/apple-mailbox.c
 F:	drivers/nvme/host/apple.c
 F:	drivers/nvmem/apple-efuses.c
 F:	drivers/pinctrl/pinctrl-apple-gpio.c
+F:	drivers/pwm/pwm-apple.c
 F:	drivers/soc/apple/*
 F:	drivers/watchdog/apple_wdt.c
 F:	include/dt-bindings/interrupt-controller/apple-aic.h
Signature · 1 line
2.37.1 (Apple Git-137.1)