imx8mm-phg: Add board support
Subsystems (3)
PATCH v2 1/1 imx8mm-phg: Add board support
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken directly from Linux 6.2-rc3.
---
Changes since v1:
- Rebased on top of current master (Tom)
- Converted doc to rst format (Tom)
- Simplified environment
arch/arm/dts/Makefile | 1 + arch/arm/dts/imx8mm-phg-u-boot.dtsi | 137 ++ arch/arm/dts/imx8mm-phg.dts | 266 +++ arch/arm/dts/imx8mm-tqma8mqml.dtsi | 341 +++ arch/arm/mach-imx/imx8m/Kconfig | 8 + board/cloos/imx8mm_phg/Kconfig | 15 + board/cloos/imx8mm_phg/MAINTAINERS | 6 + board/cloos/imx8mm_phg/Makefile | 12 + board/cloos/imx8mm_phg/imx8mm_phg.c | 50 + .../cloos/imx8mm_phg/imximage-8mm-lpddr4.cfg | 8 + board/cloos/imx8mm_phg/lpddr4_timing.c | 1846 +++++++++++++++++ board/cloos/imx8mm_phg/spl.c | 147 ++ configs/imx8mm_phg_defconfig | 120 ++ doc/board/cloos/imx8mm_phg.rst | 55 + doc/board/cloos/index.rst | 9 + doc/board/index.rst | 1 + include/configs/imx8mm_phg.h | 43 + 17 files changed, 3065 insertions(+) create mode 100644 arch/arm/dts/imx8mm-phg-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mm-phg.dts create mode 100644 arch/arm/dts/imx8mm-tqma8mqml.dtsi create mode 100644 board/cloos/imx8mm_phg/Kconfig create mode 100644 board/cloos/imx8mm_phg/MAINTAINERS create mode 100644 board/cloos/imx8mm_phg/Makefile create mode 100644 board/cloos/imx8mm_phg/imx8mm_phg.c create mode 100644 board/cloos/imx8mm_phg/imximage-8mm-lpddr4.cfg create mode 100644 board/cloos/imx8mm_phg/lpddr4_timing.c create mode 100644 board/cloos/imx8mm_phg/spl.c create mode 100644 configs/imx8mm_phg_defconfig create mode 100644 doc/board/cloos/imx8mm_phg.rst create mode 100644 doc/board/cloos/index.rst create mode 100644 include/configs/imx8mm_phg.h
arch/arm/dts/Makefile +1 -0
@@ -955,6 +955,7 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mm-kontron-bl.dtb \ imx8mm-kontron-bl-osm-s.dtb \ imx8mm-mx8menlo.dtb \ + imx8mm-phg.dtb \ imx8mm-venice.dtb \ imx8mm-venice-gw71xx-0x.dtb \ imx8mm-venice-gw72xx-0x.dtb \
arch/arm/dts/imx8mm-phg-u-boot.dtsi new file +137 -0
137 lines not on this page · raw message
arch/arm/dts/imx8mm-phg.dts new file +266 -0
266 lines not on this page · raw message
arch/arm/dts/imx8mm-tqma8mqml.dtsi new file +341 -0
341 lines not on this page · raw message
arch/arm/mach-imx/imx8m/Kconfig +8 -0
@@ -94,6 +94,13 @@ config TARGET_IMX8MM_MX8MENLO select SUPPORT_SPL select IMX8M_LPDDR4 +config TARGET_IMX8MM_PHG + bool "i.MX8MM PHG board" + select BINMAN + select IMX8MM + select SUPPORT_SPL + select IMX8M_LPDDR4 + config TARGET_IMX8MM_VENICE bool "Support Gateworks Venice iMX8M Mini module" select BINMAN
@@ -305,6 +312,7 @@ source "board/advantech/imx8mp_rsb3720a1/Kconfig" source "board/beacon/imx8mm/Kconfig" source "board/beacon/imx8mn/Kconfig" source "board/bsh/imx8mn_smm_s2/Kconfig" +source "board/cloos/imx8mm_phg/Kconfig" source "board/compulab/imx8mm-cl-iot-gate/Kconfig" source "board/data_modul/imx8mm_edm_sbc/Kconfig" source "board/dhelectronics/dh_imx8mp/Kconfig"
board/cloos/imx8mm_phg/Kconfig new file +15 -0
@@ -0,0 +1,15 @@ +if TARGET_IMX8MM_PHG + +config SYS_BOARD + default "imx8mm_phg" + +config SYS_VENDOR + default "cloos" + +config SYS_CONFIG_NAME + default "imx8mm_phg" + +config IMX_CONFIG + default "board/cloos/imx8mm_phg/imximage-8mm-lpddr4.cfg" + +endif
board/cloos/imx8mm_phg/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +i.MX8MM PHG BOARD +M: Fabio Estevam <[email protected]> +S: Maintained +F: board/cloos/imx8mm_phg/ +F: include/configs/imx8mm_phg.h +F: configs/imx8mm_phg_defconfig
board/cloos/imx8mm_phg/Makefile new file +12 -0
@@ -0,0 +1,12 @@ +# +# Copyright 2018 NXP +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += imx8mm_phg.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing.o +endif
board/cloos/imx8mm_phg/imx8mm_phg.c new file +50 -0
50 lines not on this page · raw message
board/cloos/imx8mm_phg/imximage-8mm-lpddr4.cfg new file +8 -0
@@ -0,0 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2021 NXP + */ + + +BOOT_FROM sd +LOADER u-boot-spl-ddr.bin 0x7E1000
board/cloos/imx8mm_phg/lpddr4_timing.c new file +1846 -0
1,846 lines not on this page · raw message
board/cloos/imx8mm_phg/spl.c new file +147 -0
147 lines not on this page · raw message
configs/imx8mm_phg_defconfig new file +120 -0
120 lines not on this page · raw message
doc/board/cloos/imx8mm_phg.rst new file +55 -0
25 lines not on this page · raw message
include/configs/imx8mm_phg.h new file +43 -0
43 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
2.25.1
Part of the diff is not shown here. View the raw message.
Quoted 13 lines · Fabio Estevam
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dtsandimx8mm-tqma8mqml.dtsiare taken directly from Linux 6.2-rc3.Signed-off-by Fabio Estevam <[email protected]>---
Changes since v1:
- Rebased on top of current master (Tom)
- Converted doc to rst format (Tom)
- Simplified environment
[snip]
include/configs/imx8mm_phg.h line 32
Quoted 11 lines
include/configs/imx8mm_phg.h new file +11
-0+/* Initial environment variables */ +#define CFG_EXTRA_ENV_SETTINGS \ + "console=ttymxc1,115200\0" \ + "fdtfile=imx8mm-phg.dtb\0" \ + "fdt_addr_r=0x43000000\0" \ + "mmcdev=0\0" \ + "mmcargs=setenv bootargs console=${console} root=/dev/mmcblk${mmcdev}p${mmcpart} rw rootwait quiet\0" \ + "bootcmd=env exists mmcpart || setenv mmcpart 1; run mmcargs; \ + mmc dev ${mmcdev}; load mmc ${mmcdev}:${mmcpart} ${loadaddr} boot/Image; \ + load mmc ${mmcdev}:${mmcpart} ${fdt_addr_r} boot/${fdtfile}; \ + booti ${loadaddr} - ${fdt_addr_r}\0"
We're not yet to the point of nak'ing new boards over this, but if you look at something like board/kontron/sl-mx8mm/sl-mx8mm.env the above is trivially done that way instead. Is there something blocking doing that?
Signature · 1 line
Tom
Fabio Estevam
reviewerHi Tom,
Quoted 4 lines · Tom Rini
We're not yet to the point of nak'ing new boards over this, but if you look at something like board/kontron/sl-mx8mm/sl-mx8mm.env the above is trivially done that way instead. Is there something blocking doing that?
Thanks for the suggestion. I will keep it in mind for future board submissions.
This particular board has been in use for several months and we don't want to change the
environment at this time as this would require extra rework in the BSP layer.
I plan to keep the current environment as is.
Thanks
Quoted 9 lines · Fabio Estevam
Hi Tom,
Quoted 4 lines · Tom Rini
We're not yet to the point of nak'ing new boards over this, but if you look at something like board/kontron/sl-mx8mm/sl-mx8mm.env the above is trivially done that way instead. Is there something blocking doing that?
Quoted 7 lines
Thanks for the suggestion. I will keep it in mind for future board submissions.
This particular board has been in use for several months and we don't want to change the
environment at this time as this would require extra rework in the BSP layer.I plan to keep the current environment as is.
You can use u-boot-initial-env to compare before/after and see it's unchanged :)
Signature · 1 line
Tom