amd-xgbe: PFC and KR-Training fixes
Subsystems (3)
Raju Rangoju
maintainercover amd-xgbe: PFC and KR-Training fixes
This patch series fixes the issues in kr-training and pfc
Patches:
0001 - There is difference in the TX Flow Control registers (TFCR) between the revisions of the hardware. Update the driver to use the TFCR based on the reported version of the hardware.
0002 - AN restart triggered during KR training not only aborts the KR training process but also move the HW to unstable state. Add the necessary changes to fix kr-taining.
Raju Rangoju (2):
amd-xgbe: TX Flow Ctrl Registers are h/w ver dependent
amd-xgbe: Delay AN timeout during KR training
drivers/net/ethernet/amd/xgbe/xgbe-dev.c | 23 ++++++++++++++-------- drivers/net/ethernet/amd/xgbe/xgbe-mdio.c | 24 +++++++++++++++++++++++ drivers/net/ethernet/amd/xgbe/xgbe.h | 2 ++ 3 files changed, 41 insertions(+), 8 deletions(-)
Signature · 1 line
2.25.1
Raju Rangoju
maintainerPATCH 1/2 amd-xgbe: TX Flow Ctrl Registers are h/w ver dependent
There is difference in the TX Flow Control registers (TFCR) between the revisions of the hardware. The older revisions of hardware used to have single register per queue. Whereas, the newer revision of hardware (from ver 30H onwards) have one register per priority.
Update the driver to use the TFCR based on the reported version of the hardware.
--- drivers/net/ethernet/amd/xgbe/xgbe-dev.c | 23 +++++++++++++++-------- 1 file changed, 15 insertions(+), 8 deletions(-)
drivers/net/ethernet/amd/xgbe/xgbe-dev.c +15 -8
@@ -524,19 +524,28 @@ static void xgbe_disable_vxlan(struct xgbe_prv_data *pdata)netif_dbg (pdata, drv, pdata->netdev,"VXLAN acceleration disabled\n" ); } +static unsigned int xgbe_get_fc_queue_count (struct xgbe_prv_data *pdata) +{ +unsigned int max_q_count =XGMAC_MAX_FLOW_CONTROL_QUEUES ; + +/* From MAC ver 30H the TFCR is per priority, instead of per queue */ +if (XGMAC_GET_BITS (pdata->hw_feat.version,MAC_VR ,SNPSVER ) >=0x30 ) +return max_q_count; +else + return min_t(unsigned int, pdata->tx_q_count, max_q_count); +} +static int xgbe_disable_tx_flow_control (struct xgbe_prv_data *pdata) { -unsigned int max_q_count, q_count;unsigned int reg, reg_val; -unsigned int i; +unsigned int i, q_count;/* Clear MTL flow control */ for (i =0 ; i < pdata->rx_q_count; i++)XGMAC_MTL_IOWRITE_BITS (pdata, i,MTL_Q_RQOMR ,EHFC ,0 );/* Clear MAC flow control */ - max_q_count =XGMAC_MAX_FLOW_CONTROL_QUEUES ; - q_count = min_t(unsigned int, pdata->tx_q_count, max_q_count); + q_count =xgbe_get_fc_queue_count (pdata); reg =MAC_Q0TFCR ;for (i =0 ; i < q_count; i++) { reg_val =XGMAC_IOREAD (pdata, reg);
@@ -553,9 +562,8 @@ static int xgbe_enable_tx_flow_control(struct xgbe_prv_data *pdata) {struct ieee_pfc *pfc = pdata->pfc;struct ieee_ets *ets = pdata->ets; -unsigned int max_q_count, q_count;unsigned int reg, reg_val; -unsigned int i; +unsigned int i, q_count;/* Set MTL flow control */ for (i =0 ; i < pdata->rx_q_count; i++) {
@@ -579,8 +587,7 @@ static int xgbe_enable_tx_flow_control(struct xgbe_prv_data *pdata) }/* Set MAC flow control */ - max_q_count =XGMAC_MAX_FLOW_CONTROL_QUEUES ; - q_count = min_t(unsigned int, pdata->tx_q_count, max_q_count); + q_count =xgbe_get_fc_queue_count (pdata); reg =MAC_Q0TFCR ;for (i =0 ; i < q_count; i++) { reg_val =XGMAC_IOREAD (pdata, reg);
Signature · 1 line
2.25.1
Raju Rangoju
maintainerPATCH 2/2 amd-xgbe: Delay AN timeout during KR training
In reply to Raju RangojuAN restart triggered during KR training not only aborts the KR training process but also move the HW to unstable state. Driver has to wait upto 500ms or until the KR training is completed before restarting AN cycle.
--- drivers/net/ethernet/amd/xgbe/xgbe-mdio.c | 24 +++++++++++++++++++++++ drivers/net/ethernet/amd/xgbe/xgbe.h | 2 ++ 2 files changed, 26 insertions(+)
drivers/net/ethernet/amd/xgbe/xgbe-mdio.c +24 -0
@@ -496,6 +496,7 @@ static enum xgbe_an xgbe_an73_tx_training(struct xgbe_prv_data *pdata, reg |=XGBE_KR_TRAINING_ENABLE ; reg |=XGBE_KR_TRAINING_START ;XMDIO_WRITE (pdata,MDIO_MMD_PMAPMD ,MDIO_PMA_10GBR_PMD_CTRL , reg); + pdata->kr_start_time = jiffies;netif_dbg (pdata, link, pdata->netdev,"KR training initiated\n" );
@@ -632,6 +633,8 @@ static enum xgbe_an xgbe_an73_incompat_link(struct xgbe_prv_data *pdata)xgbe_switch_mode (pdata); + pdata->an_result =XGBE_AN_READY ; +xgbe_an_restart (pdata);return XGBE_AN_INCOMPAT_LINK ;
@@ -1275,9 +1278,30 @@ static bool xgbe_phy_aneg_done(struct xgbe_prv_data *pdata)static void xgbe_check_link_timeout (struct xgbe_prv_data *pdata) {unsigned long link_timeout; +unsigned long kr_time; +int wait; link_timeout = pdata->link_check + (XGBE_LINK_TIMEOUT *HZ );if (time_after (jiffies, link_timeout)) { +if ((xgbe_cur_mode (pdata) ==XGBE_MODE_KR ) && + pdata->phy.autoneg ==AUTONEG_ENABLE ) { +/* AN restart should not happen while KR training is in progress. +* The while loop ensures no AN restart during KR training, +* waits up to 500ms and AN restart is triggered only if KR +* training is failed. +*/ + wait =XGBE_KR_TRAINING_WAIT_ITER ; +while (wait--) { + kr_time = pdata->kr_start_time + +msecs_to_jiffies (XGBE_AN_MS_TIMEOUT ); +if (time_after (jiffies, kr_time)) +break ; +/* AN restart is not required, if AN result is COMPLETE */ +if (pdata->an_result ==XGBE_AN_COMPLETE ) +return ; +usleep_range (10000 ,11000 ); + } + }netif_dbg (pdata, link, pdata->netdev,"AN link timeout\n" );xgbe_phy_config_aneg (pdata); }
drivers/net/ethernet/amd/xgbe/xgbe.h +2 -0
@@ -290,6 +290,7 @@/* Auto-negotiation */ #define XGBE_AN_MS_TIMEOUT 500#define XGBE_LINK_TIMEOUT 5 +#define XGBE_KR_TRAINING_WAIT_ITER 50#define XGBE_SGMII_AN_LINK_STATUS BIT(1)#define XGBE_SGMII_AN_LINK_SPEED (BIT(2) | BIT(3))
@@ -1280,6 +1281,7 @@ struct xgbe_prv_data {unsigned int parallel_detect;unsigned int fec_ability;unsigned long an_start; +unsigned long kr_start_time;enum xgbe_an_mode an_mode;/* I2C support */
Signature · 1 line
2.25.1
Jakub Kicinski
maintainerQuoted 7 lines · On Wed, 11 Jan 2023 22:58:50 +0530 Raju Rangoju wrote:
0001 - There is difference in the TX Flow Control registers (TFCR) between the revisions of the hardware. Update the driver to use the TFCR based on the reported version of the hardware.
0002 - AN restart triggered during KR training not only aborts the KR training process but also move the HW to unstable state. Add the necessary changes to fix kr-taining.
Please err on the side of CCing people. Here the patches under Fixes have Tom's sign off which makes our automation complain that he's not CCed. No tag from him either.
Quoted 5 lines · Jakub Kicinski
Quoted 4 lines · On Wed, 11 Jan 2023 22:58:50 +0530 Raju Rangoju wrote:
0001 - There is difference in the TX Flow Control registers (TFCR) between the revisions of the hardware. Update the driver to use the TFCR based on the reported version of the hardware.
Quoted 8 lines
Quoted 3 lines
0002 - AN restart triggered during KR training not only aborts the KR training process but also move the HW to unstable state. Add the necessary changes to fix kr-taining.
Please err on the side of CCing people. Here the patches under Fixes have Tom's sign off which makes our automation complain that he's not CCed. No tag from him either.
I have put an Ack tag to the patches in the series, being the additional maintainer for this driver. As Tom is busy working on other areas, I shall be a single maintainer for this driver going forward.
I can submit a patch for the change to the MAINTAINERS file.
But would you mind pulling this series for now? Or would you like to see the MAINTAINERS file getting updated first?
Thanks,
Shyam
Jakub Kicinski
maintainerQuoted 5 lines · On Thu, 12 Jan 2023 11:19:34 +0530 Shyam Sundar S K wrote:
I have put an Ack tag to the patches in the series, being the additional maintainer for this driver. As Tom is busy working on other areas, I shall be a single maintainer for this driver going forward.
I can submit a patch for the change to the
MAINTAINERSfile.
For Fixes of code that someone authored it'd be better if the person is CCed, as long as their email address still works. For net-next material, if you're posting as a co-maintainer not CCing other maintainers is no big deal.
Quoted 2 lines
But would you mind pulling this series for now? Or would you like to see the
MAINTAINERSfile getting updated first?
Yes, no need to repost this one. Just something to keep in mind for the future.
Quoted 11 lines · Jakub Kicinski
Quoted 5 lines · On Thu, 12 Jan 2023 11:19:34 +0530 Shyam Sundar S K wrote:
I have put an Ack tag to the patches in the series, being the additional maintainer for this driver. As Tom is busy working on other areas, I shall be a single maintainer for this driver going forward.
I can submit a patch for the change to the
MAINTAINERSfile.For Fixes of code that someone authored it'd be better if the person is CCed, as long as their email address still works. For net-next material, if you're posting as a co-maintainer not CCing other maintainers is no big deal.
Noted.
Quoted 7 lines
Quoted 3 lines
But would you mind pulling this series for now? Or would you like to see the
MAINTAINERSfile getting updated first?Yes, no need to repost this one. Just something to keep in mind for the future.
Thanks! Will take care of thie is future.
Thanks,
Shyam
Quoted 11 lines · On Wed, 11 Jan 2023 22:58:50 +0530 Raju Rangoju wrote:
This patch series fixes the issues in kr-training and pfc
Patches:
0001 - There is difference in the TX Flow Control registers (TFCR) between the revisions of the hardware. Update the driver to use the TFCR based on the reported version of the hardware.
0002 - AN restart triggered during KR training not only aborts the KR training process but also move the HW to unstable state. Add the necessary changes to fix kr-taining.
Applied, thanks!