e1000e: Add ADP_I219_LM17 to ME S0ix blacklist
Subsystems (3)
PATCH 1/1 e1000e: Add ADP_I219_LM17 to ME S0ix blacklist
I219 on HP EliteOne 840 All in One cannot work after s2idle resume when the link speed is Gigabit, Wake-on-LAN is enabled and then set the link down before suspend. No issue found when requesting driver to configure S0ix. Add workround to let ADP_I219_LM17 use the dirver configured S0ix.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216926
---
It's regarding the bug above, it looks it's causued by the ME S0ix. And is there a method to make the ME S0ix path work?
drivers/net/ethernet/intel/e1000e/netdev.c | 25 ++++++++++++++++++++++ 1 file changed, 25 insertions(+)
drivers/net/ethernet/intel/e1000e/netdev.c +25 -0
@@ -6330,6 +6330,23 @@ static void e1000e_flush_lpic(struct pci_dev *pdev)pm_runtime_put_sync (netdev->dev.parent); } +static u16 me_s0ix_blacklist[] = { +E1000_DEV_ID_PCH_ADP_I219_LM17 , +0 +}; + +static bool e1000e_check_me_s0ix_blacklist (const struct e1000_adapter *adapter) +{ +u16 *list; + +for (list = me_s0ix_blacklist; *list; list++) { +if (*list == adapter->pdev->device) +return true; + } + +return false; +} +/* S0ix implementation */ static void e1000e_s0ix_entry_flow (struct e1000_adapter *adapter) {
@@ -6337,6 +6354,9 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)u32 mac_data;u16 phy_data; +if (e1000e_check_me_s0ix_blacklist (adapter)) + goto req_driver; +if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID && hw->mac.type >= e1000_pch_adp) {/* Request ME configure the device for S0ix */
@@ -6346,6 +6366,7 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)trace_e1000e_trace_mac_register (mac_data);ew32 (H2ME , mac_data); }else { +req_driver:/* Request driver configure the device to S0ix */ /* Disable the periodic inband message, * don't request PCIe clock in K1 page770_17[10:9] = 10b
@@ -6488,6 +6509,9 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)u16 phy_data;u32 i =0 ; +if (e1000e_check_me_s0ix_blacklist (adapter)) + goto req_driver; +if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID && hw->mac.type >= e1000_pch_adp) {/* Keep the GPT clock enabled for CSME */
@@ -6523,6 +6547,7 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)else e_dbg ("DPG_EXIT_DONE cleared after %d msec\n" , i *10 ); }else { +req_driver:/* Request driver unconfigure the device from S0ix */ /* Disable the Dynamic Power Gating in the MAC */
Signature · 1 line
2.30.2
Quoted 6 lines · Jiajia Liu
I219 on HP EliteOne 840 All in One cannot work after s2idle resume when the link speed is Gigabit, Wake-on-LAN is enabled and then set the link down before suspend. No issue found when requesting driver to configure S0ix. Add workround to let
ADP_I219_LM17use the dirver configured S0ix.
Quoted 7 lines
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216926
Signed-off-by Jiajia Liu <[email protected]>---
It's regarding the bug above, it looks it's causued by the ME S0ix. And is there a method to make the ME S0ix path work?
No idea. It does seem better to disable S0ix if it doesn't work properly first though...
Quoted 17 lines
drivers/net/ethernet/intel/e1000e/netdev.c | 25 ++++++++++++++++++++++ 1 file changed, 25 insertions(+)drivers/net/ethernet/intel/e1000e/netdev.c +6
-0@@ -6330,6 +6330,23 @@ static void e1000e_flush_lpic(struct pci_dev *pdev)pm_runtime_put_sync (netdev->dev.parent); } +static u16 me_s0ix_blacklist[] = { +E1000_DEV_ID_PCH_ADP_I219_LM17 , +0 +}; + +static bool e1000e_check_me_s0ix_blacklist (const struct e1000_adapter *adapter)
drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_flush_lpic(struct pci_dev *pdev) · line 6348
Quoted 10 lines
drivers/net/ethernet/intel/e1000e/netdev.c +10
-0+{ +u16 *list; + +for (list = me_s0ix_blacklist; *list; list++) { +if (*list == adapter->pdev->device) +return true; + } + +return false; +}
The name of this function seems odd..? "check_me"? It also seems like we could just do a simple switch/case on the device ID or similar.
Maybe: "e1000e_device_supports_s0ix"?
Quoted 5 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0+/* S0ix implementation */ static void e1000e_s0ix_entry_flow (struct e1000_adapter *adapter) {
drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter) · line 6362
Quoted 9 lines
drivers/net/ethernet/intel/e1000e/netdev.c +3
-0@@ -6337,6 +6354,9 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)u32 mac_data;u16 phy_data; +if (e1000e_check_me_s0ix_blacklist (adapter)) + goto req_driver; +if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID && hw->mac.type >= e1000_pch_adp) {/* Request ME configure the device for S0ix */
The related code also seems to already perform some set of mac checks here...
Quoted 8 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0@@ -6346,6 +6366,7 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)trace_e1000e_trace_mac_register (mac_data);ew32 (H2ME , mac_data); }else { +req_driver:> /* Request driver configure the device to S0ix *//* Disable the periodic inband message, * don't request PCIe clock in K1 page770_17[10:9] = 10b
drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) · line 6514
Quoted 6 lines
drivers/net/ethernet/intel/e1000e/netdev.c +3
-0@@ -6488,6 +6509,9 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)u16 phy_data;u32 i =0 ; +if (e1000e_check_me_s0ix_blacklist (adapter)) + goto req_driver; +
Why not just combine this check into the statement below rather than adding a goto?
drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) · line 6553
Quoted 11 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID && hw->mac.type >= e1000_pch_adp) {/* Keep the GPT clock enabled for CSME */ @@ -6523,6 +6547,7 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)else e_dbg ("DPG_EXIT_DONE cleared after %d msec\n" , i *10 ); }else { +req_driver:/* Request driver unconfigure the device from S0ix */ /* Disable the Dynamic Power Gating in the MAC */
_______________________________________________
Intel-wired-lan mailing list
[email protected]
https://lists.osuosl.org/mailman/listinfo/intel-wired-lan
Quoted 9 lines · Jacob Keller
Quoted 6 lines · Jiajia Liu
I219 on HP EliteOne 840 All in One cannot work after s2idle resume when the link speed is Gigabit, Wake-on-LAN is enabled and then set the link down before suspend. No issue found when requesting driver to configure S0ix. Add workround to let
ADP_I219_LM17use the dirver configured S0ix.
Quoted 6 lines
Quoted 6 lines
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216926
Signed-off-by Jiajia Liu <[email protected]>---
It's regarding the bug above, it looks it's causued by the ME S0ix. And is there a method to make the ME S0ix path work?
No. This is a fragile approach. ME must get the message from us (unconfigure the device from s0ix). Otherwise, ME will continue to access LAN resources and the controller could get stuck. I see two ways:
1. you always can skip s0ix flow by priv_flag
2. Especially in this case (HP platform) - please, contact HP (what is the ME version on this system, and how was it released...). HP will open a ticket with Intel. (then we can involve the ME team)
Quoted 85 lines
Quoted 1 line
No idea. It does seem better to disable S0ix if it doesn't work properly first though...
Quoted 17 lines
drivers/net/ethernet/intel/e1000e/netdev.c | 25 ++++++++++++++++++++++ 1 file changed, 25 insertions(+)drivers/net/ethernet/intel/e1000e/netdev.c +6
-0@@ -6330,6 +6330,23 @@ static void e1000e_flush_lpic(struct pci_dev *pdev)pm_runtime_put_sync (netdev->dev.parent); } +static u16 me_s0ix_blacklist[] = { +E1000_DEV_ID_PCH_ADP_I219_LM17 , +0 +}; + +static bool e1000e_check_me_s0ix_blacklist (const struct e1000_adapter *adapter)drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_flush_lpic(struct pci_dev *pdev) · line 6348
Quoted 10 lines
drivers/net/ethernet/intel/e1000e/netdev.c +10
-0+{ +u16 *list; + +for (list = me_s0ix_blacklist; *list; list++) { +if (*list == adapter->pdev->device) +return true; + } + +return false; +}The name of this function seems odd..? "
check_me"? It also seems like we could just do a simple switch/case on the device ID or similar.Maybe: "
e1000e_device_supports_s0ix"?Quoted 5 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0+/* S0ix implementation */ static void e1000e_s0ix_entry_flow (struct e1000_adapter *adapter) {drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter) · line 6362
Quoted 9 lines
drivers/net/ethernet/intel/e1000e/netdev.c +3
-0@@ -6337,6 +6354,9 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)u32 mac_data;u16 phy_data; +if (e1000e_check_me_s0ix_blacklist (adapter)) + goto req_driver; +if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID && hw->mac.type >= e1000_pch_adp) {/* Request ME configure the device for S0ix */ The related code also seems to already perform some set of mac checks here...
Quoted 8 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0@@ -6346,6 +6366,7 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)trace_e1000e_trace_mac_register (mac_data);ew32 (H2ME , mac_data); }else { +req_driver:> /* Request driver configure the device to S0ix *//* Disable the periodic inband message, * don't request PCIe clock in K1 page770_17[10:9] = 10b drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) · line 6514
Quoted 6 lines
drivers/net/ethernet/intel/e1000e/netdev.c +3
-0@@ -6488,6 +6509,9 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)u16 phy_data;u32 i =0 ; +if (e1000e_check_me_s0ix_blacklist (adapter)) + goto req_driver; +Why not just combine this check into the statement below rather than adding a goto?
Quoted 10 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID && hw->mac.type >= e1000_pch_adp) {/* Keep the GPT clock enabled for CSME */ @@ -6523,6 +6547,7 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)else e_dbg ("DPG_EXIT_DONE cleared after %d msec\n" , i *10 ); }else { +req_driver:/* Request driver unconfigure the device from S0ix */
Quoted 5 lines
drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) · line 6553
Quoted 1 line
drivers/net/ethernet/intel/e1000e/netdev.c +0
-0/* Disable the Dynamic Power Gating in the MAC */ _______________________________________________
Intel-wired-lan mailing list
[email protected]
https://lists.osuosl.org/mailman/listinfo/intel-wired-lan
_______________________________________________
Intel-wired-lan mailing list
[email protected]
https://lists.osuosl.org/mailman/listinfo/intel-wired-lan
Quoted 17 lines · Sasha
Quoted 9 lines · Jacob Keller
Quoted 6 lines · Jiajia Liu
I219 on HP EliteOne 840 All in One cannot work after s2idle resume when the link speed is Gigabit, Wake-on-LAN is enabled and then set the link down before suspend. No issue found when requesting driver to configure S0ix. Add workround to let
ADP_I219_LM17use the dirver configured S0ix.Quoted 6 lines
Quoted 6 lines
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216926
Signed-off-by Jiajia Liu <[email protected]>---
It's regarding the bug above, it looks it's causued by the ME S0ix. And is there a method to make the ME S0ix path work?
Quoted 8 lines
No. This is a fragile approach. ME must get the message from us (unconfigure the device from s0ix). Otherwise, ME will continue to access LAN resources and the controller could get stuck.
I see two ways:
1. you always can skip s0ix flow bypriv_flag
2. Especially in this case (HP platform) - please, contact HP (what is the ME version on this system, and how was it released...). HP will open a ticket with Intel. (then we can involve the ME team)
HP released BIOS including ME firmware on their website HP.com at
https://support.hp.com/my-en/drivers/selfservice/hp-eliteone-840-23.8-inch-g9-all-in-one-desktop-pc/2101132389.
There is upgrade interface on the BIOS setup menu which can connect HP.com and upgrade to newer BIOS.
The initial ME version was v16.0.15.1735 from BIOS 02.03.04. Then I upgraded to the latest one v16.1.25.1932v3 from BIOS 02.06.01 released on Nov 28, 2022. Both of them can produce this issue.
I have only one setup. Is it possible to try on your system which has the same I219-LM to see if it's platform specific or not?
Quoted 91 lines
Quoted 90 lines
Quoted 1 line
No idea. It does seem better to disable S0ix if it doesn't work properly first though...
Quoted 17 lines
drivers/net/ethernet/intel/e1000e/netdev.c | 25 ++++++++++++++++++++++ 1 file changed, 25 insertions(+)drivers/net/ethernet/intel/e1000e/netdev.c +6
-0@@ -6330,6 +6330,23 @@ static void e1000e_flush_lpic(struct pci_dev *pdev)pm_runtime_put_sync (netdev->dev.parent); } +static u16 me_s0ix_blacklist[] = { +E1000_DEV_ID_PCH_ADP_I219_LM17 , +0 +}; + +static bool e1000e_check_me_s0ix_blacklist (const struct e1000_adapter *adapter)drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_flush_lpic(struct pci_dev *pdev) · line 6348
Quoted 10 lines
drivers/net/ethernet/intel/e1000e/netdev.c +10
-0+{ +u16 *list; + +for (list = me_s0ix_blacklist; *list; list++) { +if (*list == adapter->pdev->device) +return true; + } + +return false; +}The name of this function seems odd..? "
check_me"? It also seems like we could just do a simple switch/case on the device ID or similar.Maybe: "
e1000e_device_supports_s0ix"?Quoted 5 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0+/* S0ix implementation */ static void e1000e_s0ix_entry_flow (struct e1000_adapter *adapter) {drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter) · line 6362
Quoted 9 lines
drivers/net/ethernet/intel/e1000e/netdev.c +3
-0@@ -6337,6 +6354,9 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)u32 mac_data;u16 phy_data; +if (e1000e_check_me_s0ix_blacklist (adapter)) + goto req_driver; +if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID && hw->mac.type >= e1000_pch_adp) {/* Request ME configure the device for S0ix */ The related code also seems to already perform some set of mac checks here...
Quoted 8 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0@@ -6346,6 +6366,7 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)trace_e1000e_trace_mac_register (mac_data);ew32 (H2ME , mac_data); }else { +req_driver:> /* Request driver configure the device to S0ix *//* Disable the periodic inband message, * don't request PCIe clock in K1 page770_17[10:9] = 10b drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) · line 6514
Quoted 6 lines
drivers/net/ethernet/intel/e1000e/netdev.c +3
-0@@ -6488,6 +6509,9 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)u16 phy_data;u32 i =0 ; +if (e1000e_check_me_s0ix_blacklist (adapter)) + goto req_driver; +Why not just combine this check into the statement below rather than adding a goto?
drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) · line 6553
Quoted 11 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID && hw->mac.type >= e1000_pch_adp) {/* Keep the GPT clock enabled for CSME */ @@ -6523,6 +6547,7 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)else e_dbg ("DPG_EXIT_DONE cleared after %d msec\n" , i *10 ); }else { +req_driver:/* Request driver unconfigure the device from S0ix */ /* Disable the Dynamic Power Gating in the MAC */ _______________________________________________
Intel-wired-lan mailing list
[email protected]
https://lists.osuosl.org/mailman/listinfo/intel-wired-lan
Quoted 32 lines · Jia Liu
Quoted 17 lines · Sasha
Quoted 9 lines · Jacob Keller
Quoted 6 lines · Jiajia Liu
I219 on HP EliteOne 840 All in One cannot work after s2idle resume when the link speed is Gigabit, Wake-on-LAN is enabled and then set the link down before suspend. No issue found when requesting driver to configure S0ix. Add workround to let
ADP_I219_LM17use the dirver configured S0ix.Quoted 6 lines
Quoted 6 lines
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216926
Signed-off-by Jiajia Liu <[email protected]>---
It's regarding the bug above, it looks it's causued by the ME S0ix. And is there a method to make the ME S0ix path work?
Quoted 8 lines
No. This is a fragile approach. ME must get the message from us (unconfigure the device from s0ix). Otherwise, ME will continue to access LAN resources and the controller could get stuck.
I see two ways:
1. you always can skip s0ix flow bypriv_flag
2. Especially in this case (HP platform) - please, contact HP (what is the ME version on this system, and how was it released...). HP will open a ticket with Intel. (then we can involve the ME team)HP released BIOS including ME firmware on their website HP.com at
https://support.hp.com/my-en/drivers/selfservice/hp-eliteone-840-23.8-inch-g9-all-in-one-desktop-pc/2101132389.
There is upgrade interface on the BIOS setup menu which can connect HP.com and upgrade to newer BIOS.
Quoted 6 lines
The initial ME version was v16.0.15.1735 from BIOS 02.03.04. Then I upgraded to the latest one v16.1.25.1932v3 from BIOS 02.06.01 released on Nov 28, 2022. Both of them can produce this issue.
I have only one setup. Is it possible to try on your system which has the same I219-LM to see if it's platform specific or not?
Yes, s0ix flows works on our platforms.
Quoted 86 lines
Quoted 86 lines
Quoted 86 lines
Quoted 2 lines
No idea. It does seem better to disable S0ix if it doesn't work properly first though...
Quoted 17 lines
drivers/net/ethernet/intel/e1000e/netdev.c | 25 ++++++++++++++++++++++ 1 file changed, 25 insertions(+)drivers/net/ethernet/intel/e1000e/netdev.c +6
-0@@ -6330,6 +6330,23 @@ static void e1000e_flush_lpic(struct pci_dev *pdev)pm_runtime_put_sync (netdev->dev.parent); } +static u16 me_s0ix_blacklist[] = { +E1000_DEV_ID_PCH_ADP_I219_LM17 , +0 +}; + +static bool e1000e_check_me_s0ix_blacklist (const struct e1000_adapter *adapter)drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_flush_lpic(struct pci_dev *pdev) · line 6348
Quoted 10 lines
drivers/net/ethernet/intel/e1000e/netdev.c +10
-0+{ +u16 *list; + +for (list = me_s0ix_blacklist; *list; list++) { +if (*list == adapter->pdev->device) +return true; + } + +return false; +}The name of this function seems odd..? "
check_me"? It also seems like we could just do a simple switch/case on the device ID or similar.Maybe: "
e1000e_device_supports_s0ix"?Quoted 5 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0+/* S0ix implementation */ static void e1000e_s0ix_entry_flow (struct e1000_adapter *adapter) {drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter) · line 6362
Quoted 9 lines
drivers/net/ethernet/intel/e1000e/netdev.c +3
-0@@ -6337,6 +6354,9 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)u32 mac_data;u16 phy_data; +if (e1000e_check_me_s0ix_blacklist (adapter)) + goto req_driver; +if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID && hw->mac.type >= e1000_pch_adp) {/* Request ME configure the device for S0ix */ The related code also seems to already perform some set of mac checks here...
Quoted 8 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0@@ -6346,6 +6366,7 @@ static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)trace_e1000e_trace_mac_register (mac_data);ew32 (H2ME , mac_data); }else { +req_driver:> /* Request driver configure the device to S0ix *//* Disable the periodic inband message, * don't request PCIe clock in K1 page770_17[10:9] = 10b drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) · line 6514
Quoted 6 lines
drivers/net/ethernet/intel/e1000e/netdev.c +3
-0@@ -6488,6 +6509,9 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)u16 phy_data;u32 i =0 ; +if (e1000e_check_me_s0ix_blacklist (adapter)) + goto req_driver; +Why not just combine this check into the statement below rather than adding a goto?
Quoted 10 lines
drivers/net/ethernet/intel/e1000e/netdev.c +1
-0if (er32 (FWSM ) &E1000_ICH_FWSM_FW_VALID && hw->mac.type >= e1000_pch_adp) {/* Keep the GPT clock enabled for CSME */ @@ -6523,6 +6547,7 @@ static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)else e_dbg ("DPG_EXIT_DONE cleared after %d msec\n" , i *10 ); }else { +req_driver:/* Request driver unconfigure the device from S0ix */
Quoted 6 lines
Quoted 6 lines
Quoted 5 lines
drivers/net/ethernet/intel/e1000e/netdev.c static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter) · line 6553
Quoted 1 line
drivers/net/ethernet/intel/e1000e/netdev.c +0
-0/* Disable the Dynamic Power Gating in the MAC */ _______________________________________________
Intel-wired-lan mailing list
[email protected]
https://lists.osuosl.org/mailman/listinfo/intel-wired-lan
_______________________________________________
Intel-wired-lan mailing list
[email protected]
https://lists.osuosl.org/mailman/listinfo/intel-wired-lan