Skip to contentSkip to conversation

dt-bindings: arm: Add Data Modul i.MX8M Plus eDM SBC

PATCH Superseded Marek Vasut 1 participant 2 messages Jan 29, 2023

Subsystems (2)

v4 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

PATCH v4 1/2 dt-bindings: arm: Add Data Modul i.MX8M Plus eDM SBC

Add DT compatible for Data Modul i.MX8M Plus eDM SBC board. This is an evaluation board for various custom display units.

---
Cc: Fabio Estevam <[email protected]>
Cc: Frieder Schrempf <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Li Yang <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Matthias Schiffer <[email protected]>
Cc: Max Krummenacher <[email protected]>
Cc: NXP Linux Team <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: [email protected]
To: [email protected]
---
V2: Add AB from Krzysztof
V3: No change
V4: Rebase on next-20230127

---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/fsl.yaml +1 -0
index 442ce8f4d6756..365ff7fdf34c5 100644
@@ -1002,6 +1002,7 @@ properties:
         items:
           - enum:
               - beacon,imx8mp-beacon-kit  # i.MX8MP Beacon Development Kit
+              - dmo,imx8mp-data-modul-edm-sbc # i.MX8MP eDM SBC
               - fsl,imx8mp-evk            # i.MX8MP EVK Board
               - gateworks,imx8mp-gw74xx   # i.MX8MP Gateworks Board
               - polyhex,imx8mp-debix      # Polyhex Debix boards
Signature · 1 line
2.39.0
#1 lore raw

PATCH v4 2/2 arm64: dts: imx8mp: Add support for Data Modul i.MX8M Plus eDM SBC

Add support for Data Modul i.MX8M Plus eDM SBC board. This is an evaluation board for various custom display units. Currently supported are serial console, ethernet, eMMC, SD, SPI NOR, USB host and USB OTG.

---
Cc: Fabio Estevam <[email protected]>
Cc: Frieder Schrempf <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Li Yang <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Matthias Schiffer <[email protected]>
Cc: Max Krummenacher <[email protected]>
Cc: NXP Linux Team <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: [email protected]
To: [email protected]
---
V2: - Rename clk-xtal25 node to clock-xtal25
- Add comment regarding panel node compatible string
- Swap gpio and enable-active-high properties in regulator-usdhc2-vmmc node
- Move compatible string property to the beginning of watchdog node
- Move pinctrl* properties in usb-hub and rtc i2c1 subnodes below reg property
- Move iomuxc node to the end of DT and add comment about it
- Add comment regarding regulator-fixed gpio property GPIO flags
- Add no-sd and no-sdio to eMMC
V3: Drop sd-vsel-gpios from PMIC node
V4: Rebase on next-20230127

---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../freescale/imx8mp-data-modul-edm-sbc.dts   | 977 ++++++++++++++++++
 2 files changed, 978 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts
arch/arm64/boot/dts/freescale/Makefile +1 -0
index 198fff3731ae4..7193caaea40c9 100644
@@ -89,6 +89,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts new file +977 -0

977 lines not on this page · raw message

Signature · 1 line
2.39.0