arm: psci: Add PSCI v1.1 macro
Subsystems (4)
PATCH 1/10 arm: psci: Add PSCI v1.1 macro
Add macro representing the PSCI v1.1 .
---
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Andrejs Cainikovs <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Manoj Sai <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Ricardo Salveti <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Ye Li <[email protected]>
--- arch/arm/include/asm/psci.h | 1 + 1 file changed, 1 insertion(+)
arch/arm/include/asm/psci.h +1 -0
@@ -22,6 +22,7 @@#include <linux/bitops.h> #endif +#define ARM_PSCI_VER_1_1 (0x00010001)#define ARM_PSCI_VER_1_0 (0x00010000)#define ARM_PSCI_VER_0_2 (0x00000002)
Signature · 1 line
2.35.1
PATCH 2/10 arm: psci: Fix RESET2 hook
The RESET2 hook is a PSCI v1.1 functionality, rename the macro accordinly. Add missing handler for the RESET2 hook, so it can be implemented by U-Boot.
---
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Andrejs Cainikovs <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Manoj Sai <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Ricardo Salveti <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Ye Li <[email protected]>
--- arch/arm/cpu/armv8/fwcall.c | 2 +- arch/arm/cpu/armv8/psci.S | 2 ++ arch/arm/include/asm/psci.h | 4 +++- 3 files changed, 6 insertions(+), 2 deletions(-)
arch/arm/cpu/armv8/fwcall.c +1 -1
@@ -103,7 +103,7 @@ void __noreturn psci_system_reset2(u32 reset_level, u32 cookie) {struct pt_regs regs; - regs.regs[0 ] =ARM_PSCI_0_2_FN64_SYSTEM_RESET2 ; + regs.regs[0 ] =ARM_PSCI_1_1_FN64_SYSTEM_RESET2 ; regs.regs[1 ] =PSCI_RESET2_TYPE_VENDOR | reset_level; regs.regs[2 ] = cookie;if (use_smc_for_psci)
arch/arm/cpu/armv8/psci.S +2 -0
@@ -82,6 +82,7 @@ PSCI_DEFAULT(psci_node_hw_state_64) PSCI_DEFAULT(psci_system_suspend_64) PSCI_DEFAULT(psci_stat_residency_64) PSCI_DEFAULT(psci_stat_count_64) +PSCI_DEFAULT(psci_system_reset2_64) .align 3 _psci_64_table:
@@ -95,6 +96,7 @@ PSCI_TABLE(ARM_PSCI_1_0_FN64_NODE_HW_STATE, psci_node_hw_state_64) PSCI_TABLE(ARM_PSCI_1_0_FN64_SYSTEM_SUSPEND, psci_system_suspend_64) PSCI_TABLE(ARM_PSCI_1_0_FN64_STAT_RESIDENCY, psci_stat_residency_64) PSCI_TABLE(ARM_PSCI_1_0_FN64_STAT_COUNT, psci_stat_count_64) +PSCI_TABLE(ARM_PSCI_1_1_FN64_SYSTEM_RESET2, psci_system_reset2_64) PSCI_TABLE(0, 0) .macro psci_enter
arch/arm/include/asm/psci.h +3 -1
@@ -69,7 +69,6 @@#define ARM_PSCI_0_2_FN64_AFFINITY_INFO ARM_PSCI_0_2_FN64(4)#define ARM_PSCI_0_2_FN64_MIGRATE ARM_PSCI_0_2_FN64(5)#define ARM_PSCI_0_2_FN64_MIGRATE_INFO_UP_CPU ARM_PSCI_0_2_FN64(7) -#define ARM_PSCI_0_2_FN64_SYSTEM_RESET2 ARM_PSCI_0_2_FN64(18)/* PSCI 1.0 interface */ #define ARM_PSCI_1_0_FN_PSCI_FEATURES ARM_PSCI_0_2_FN(10)
@@ -87,6 +86,9 @@#define ARM_PSCI_1_0_FN64_STAT_RESIDENCY ARM_PSCI_0_2_FN64(16)#define ARM_PSCI_1_0_FN64_STAT_COUNT ARM_PSCI_0_2_FN64(17) +/* PSCI 1.1 interface */ +#define ARM_PSCI_1_1_FN64_SYSTEM_RESET2 ARM_PSCI_0_2_FN64(18) +/* 1KB stack per core */ #define ARM_PSCI_STACK_SHIFT 10#define ARM_PSCI_STACK_SIZE (1 << ARM_PSCI_STACK_SHIFT)
Signature · 1 line
2.35.1
PATCH 2/10 arm: psci: Fix RESET2 hook
Quoted 3 lines
The RESET2 hook is a PSCI v1.1 functionality, rename the macro accordinly. Add missing handler for the RESET2 hook, so it can be implemented by U-Boot.
Signed-off-by Marek Vasut <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 3/10 arm: imx: Drop custom lowlevel_init
In reply to Marek VasutThe custom lowlevel_init implementation is no longer necessary, since it is responsible for routing and trapping SErrors in U-Boot in EL2, which is implemented in common code since commit:6c7691edd55 ("armv8: Always unmask SErrors")
---
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Andrejs Cainikovs <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Manoj Sai <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Ricardo Salveti <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Ye Li <[email protected]>
--- arch/arm/mach-imx/Makefile | 2 -- arch/arm/mach-imx/lowlevel.S | 22 ---------------------- 2 files changed, 24 deletions(-) delete mode 100644 arch/arm/mach-imx/lowlevel.S
arch/arm/mach-imx/Makefile +0 -2
@@ -235,8 +235,6 @@ endif targets += $(addprefix ../../../,SPL spl/u-boot-spl.cfgout u-boot-dtb.cfgout u-boot.cfgout u-boot.uim spl/u-boot-nand-spl.imx) -obj-$(CONFIG_ARM64) += lowlevel.o - obj-$(CONFIG_MX5) += mx5/ obj-$(CONFIG_MX6) += mx6/ obj-$(CONFIG_MX7) += mx7/
arch/arm/mach-imx/lowlevel.S deleted +0 -22
@@ -1,22 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2019 NXP - */ - -#include <linux/linkage.h> - -ENTRY(lowlevel_init) - mrs x0, CurrentEL - cmp x0, #8 - b.eq 1f - ret -1: - msr daifclr, #4 - - /* set HCR_EL2.AMO to catch SERROR */ - mrs x0, hcr_el2 - orr x0, x0, #0x20 - msr hcr_el2, x0 - isb - ret -ENDPROC(lowlevel_init)
Signature · 1 line
2.35.1
PATCH 3/10 arm: imx: Drop custom lowlevel_init
Quoted 5 lines
The custom
lowlevel_initimplementation is no longer necessary, since it is responsible for routing and trapping SErrors in U-Boot in EL2, which is implemented in common code since commit:6c7691edd55("armv8: Always unmask SErrors")Signed-off-by Marek Vasut <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 4/10 arm: dts: imx8m: Require ATF BL31 blob only if not PSCI provider
In reply to Marek VasutIn case U-Boot itself if the PSCI provider on i.MX8M, do not require the ATF BL31 blob, as at that point the blob is useless and would interfere with U-Boot operation.
---
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Andrejs Cainikovs <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Manoj Sai <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Ricardo Salveti <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Ye Li <[email protected]>
--- arch/arm/dts/imx8mm-u-boot.dtsi | 4 ++++ arch/arm/dts/imx8mn-u-boot.dtsi | 4 ++++ arch/arm/dts/imx8mp-u-boot.dtsi | 4 ++++ arch/arm/dts/imx8mq-u-boot.dtsi | 4 ++++ 4 files changed, 16 insertions(+)
arch/arm/dts/imx8mm-u-boot.dtsi +4 -0
@@ -99,6 +99,7 @@ }; }; +#ifndef CONFIG_ARMV8_PSCI atf { arch = "arm64"; compression = "none";
@@ -112,6 +113,7 @@ type = "atf-bl31"; }; }; +#endif binman_fip: fip { arch = "arm64";
@@ -140,7 +142,9 @@ description = "NAME"; fdt = "fdt-SEQ"; firmware = "uboot"; +#ifndef CONFIG_ARMV8_PSCI loadables = "atf"; +#endif }; }; };
arch/arm/dts/imx8mn-u-boot.dtsi +4 -0
@@ -161,6 +161,7 @@ }; }; +#ifndef CONFIG_ARMV8_PSCI atf { arch = "arm64"; compression = "none";
@@ -174,6 +175,7 @@ type = "atf-bl31"; }; }; +#endif binman_fip: fip { arch = "arm64";
@@ -202,7 +204,9 @@ description = "NAME"; fdt = "fdt-SEQ"; firmware = "uboot"; +#ifndef CONFIG_ARMV8_PSCI loadables = "atf"; +#endif }; }; };
arch/arm/dts/imx8mp-u-boot.dtsi +4 -0
@@ -120,6 +120,7 @@ }; }; +#ifndef CONFIG_ARMV8_PSCI atf { description = "ARM Trusted Firmware"; type = "firmware";
@@ -133,6 +134,7 @@ type = "atf-bl31"; }; }; +#endif @fdt-SEQ { description = "NAME";
@@ -152,7 +154,9 @@ description = "NAME"; fdt = "fdt-SEQ"; firmware = "uboot"; +#ifndef CONFIG_ARMV8_PSCI loadables = "atf"; +#endif }; }; };
arch/arm/dts/imx8mq-u-boot.dtsi +4 -0
@@ -114,6 +114,7 @@ }; }; +#ifndef CONFIG_ARMV8_PSCI atf { arch = "arm64"; compression = "none";
@@ -127,6 +128,7 @@ type = "blob-ext"; }; }; +#endif fdt { compression = "none";
@@ -147,7 +149,9 @@ description = "NAME"; fdt = "fdt"; firmware = "uboot"; +#ifndef CONFIG_ARMV8_PSCI loadables = "atf"; +#endif }; }; };
Signature · 1 line
2.35.1
PATCH 4/10 arm: dts: imx8m: Require ATF BL31 blob only if not PSCI provider
Quoted 4 lines
In case U-Boot itself if the PSCI provider on i.MX8M, do not require the ATF BL31 blob, as at that point the blob is useless and would interfere with U-Boot operation.
Signed-off-by Marek Vasut <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 5/10 arm: imx: imx8m: Only use ROM pointers if not PSCI provider
In reply to Marek VasutThe ROM pointers are in fact populated by the ATF BL31 blob, in case U-Boot itself if the PSCI provider, there is no ATF BL31 blob, hence ignore the ROM pointers.
---
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Andrejs Cainikovs <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Manoj Sai <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Ricardo Salveti <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Ye Li <[email protected]>
--- arch/arm/mach-imx/imx8m/soc.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-)
arch/arm/mach-imx/imx8m/soc.c +5 -4
@@ -238,7 +238,7 @@ int dram_init(void)return ret;/* rom_pointer[1] contains the size of TEE occupies */ -if (rom_pointer[1 ]) +if (!IS_ENABLED (CONFIG_ARMV8_PSCI ) && rom_pointer[1 ]) gd->ram_size = sdram_size - rom_pointer[1 ];else gd->ram_size = sdram_size;
@@ -267,7 +267,7 @@ int dram_init_banksize(void) } gd->bd->bi_dram[bank].start =PHYS_SDRAM ; -if (rom_pointer[1 ]) { +if (!IS_ENABLED (CONFIG_ARMV8_PSCI ) && rom_pointer[1 ]) {phys_addr_t optee_start = (phys_addr_t )rom_pointer[0 ];phys_size_t optee_size = (size_t )rom_pointer[1 ];
@@ -312,7 +312,7 @@ phys_size_t get_effective_memsize(void) sdram_b1_size = sdram_size; } -if (rom_pointer[1 ]) { +if (!IS_ENABLED (CONFIG_ARMV8_PSCI ) && rom_pointer[1 ]) {/* We will relocate u-boot to Top of dram1. Tee position has two cases: * 1. At the top of dram1, Then return the size removed optee size. * 2. In the middle of dram1, return the size of dram1.
@@ -344,7 +344,8 @@ phys_size_t board_get_usable_ram_top(phys_size_t total_size)* rom_pointer[1] stores the size TEE uses. * We need to reserve the memory region for TEE. */ -if (rom_pointer[0 ] && rom_pointer[1 ] && top_addr > rom_pointer[0 ]) +if (!IS_ENABLED (CONFIG_ARMV8_PSCI ) && rom_pointer[0 ] && + rom_pointer[1 ] && top_addr > rom_pointer[0 ]) top_addr = rom_pointer[0 ];return top_addr;
Signature · 1 line
2.35.1
PATCH 5/10 arm: imx: imx8m: Only use ROM pointers if not PSCI provider
Quoted 4 lines
The ROM pointers are in fact populated by the ATF BL31 blob, in case U-Boot itself if the PSCI provider, there is no ATF BL31 blob, hence ignore the ROM pointers.
Signed-off-by Marek Vasut <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 6/10 arm: imx: imx8m: Enable GICv3 support if PSCI provider
In reply to Marek VasutIn case U-Boot is a PSCI provider, enable GICv3 support as this is necessary to bring up secondary cores.
---
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Andrejs Cainikovs <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Manoj Sai <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Ricardo Salveti <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Ye Li <[email protected]>
--- arch/arm/include/asm/arch-imx8m/imx-regs.h | 3 +++ arch/arm/mach-imx/imx8m/Kconfig | 1 + 2 files changed, 4 insertions(+)
arch/arm/include/asm/arch-imx8m/imx-regs.h +3 -0
@@ -81,6 +81,9 @@#define MXS_GPMI_BASE (APBH_DMA_ARB_BASE_ADDR + 0x02000)#define MXS_BCH_BASE (APBH_DMA_ARB_BASE_ADDR + 0x04000) +#define GICD_BASE 0x38800000 +#define GICR_BASE 0x38880000 +#define DDRC_DDR_SS_GPR0 0x3d000000#define DDRC_IPS_BASE_ADDR (X ) (0x3d400000 + ((X) * 0x2000000))#define DDR_CSD1_BASE_ADDR 0x40000000
arch/arm/mach-imx/imx8m/Kconfig +1 -0
@@ -2,6 +2,7 @@ if ARCH_IMX8M config IMX8M bool + select GICV3 if ARMV8_PSCI select HAS_CAAM select ROM_UNIFIED_SECTIONS select ARMV8_CRYPTO
Signature · 1 line
2.35.1
PATCH 6/10 arm: imx: imx8m: Enable GICv3 support if PSCI provider
Quoted 3 lines
In case U-Boot is a PSCI provider, enable GICv3 support as this is necessary to bring up secondary cores.
Signed-off-by Marek Vasut <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 7/10 arm: imx: imx8m: Map RAM as NS if PSCI provider
In reply to Marek VasutIn case U-Boot is a PSCI provider, map RAM explicitly as NS, otherwise secondary cores crash with SError when attempting to access RAM mapped as secure in EL2.
---
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Andrejs Cainikovs <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Manoj Sai <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Ricardo Salveti <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Ye Li <[email protected]>
--- arch/arm/mach-imx/imx8m/soc.c | 16 +++++++++++----- 1 file changed, 11 insertions(+), 5 deletions(-)
arch/arm/mach-imx/imx8m/soc.c +11 -5
@@ -100,6 +100,12 @@ void set_wdog_reset(struct wdog_regs *wdog)setbits_le16 (&wdog->wcr,WDOG_WDT_MASK |WDOG_WDZST_MASK ); } +#ifdef CONFIG_ARMV8_PSCI +#define PTE_MAP_NS PTE_BLOCK_NS +#else +#define PTE_MAP_NS 0 +#endif +static struct mm_region imx8m_mem_map[] = { {/* ROM */
@@ -122,7 +128,7 @@ static struct mm_region imx8m_mem_map[] = { .phys = 0x180000UL, .size = 0x8000UL, .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | - PTE_BLOCK_OUTER_SHARE + PTE_BLOCK_OUTER_SHARE | PTE_MAP_NS }, {/* TCM */ .virt = 0x7C0000UL,
@@ -130,14 +136,14 @@ static struct mm_region imx8m_mem_map[] = { .size = 0x80000UL, .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | PTE_BLOCK_NON_SHARE | - PTE_BLOCK_PXN | PTE_BLOCK_UXN + PTE_BLOCK_PXN | PTE_BLOCK_UXN | PTE_MAP_NS }, {/* OCRAM */ .virt = 0x900000UL, .phys = 0x900000UL, .size = 0x200000UL, .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | - PTE_BLOCK_OUTER_SHARE + PTE_BLOCK_OUTER_SHARE | PTE_MAP_NS }, {/* AIPS */ .virt = 0xB00000UL,
@@ -152,7 +158,7 @@ static struct mm_region imx8m_mem_map[] = { .phys = 0x40000000UL, .size = PHYS_SDRAM_SIZE, .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | - PTE_BLOCK_OUTER_SHARE + PTE_BLOCK_OUTER_SHARE | PTE_MAP_NS#ifdef PHYS_SDRAM_2_SIZE }, {/* DRAM2 */
@@ -160,7 +166,7 @@ static struct mm_region imx8m_mem_map[] = { .phys = 0x100000000UL, .size = PHYS_SDRAM_2_SIZE, .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | - PTE_BLOCK_OUTER_SHARE + PTE_BLOCK_OUTER_SHARE | PTE_MAP_NS#endif }, {/* empty entrie to split table entry 5 if needed when TEEs are used */
Signature · 1 line
2.35.1
PATCH 7/10 arm: imx: imx8m: Map RAM as NS if PSCI provider
Quoted 4 lines
In case U-Boot is a PSCI provider, map RAM explicitly as NS, otherwise secondary cores crash with SError when attempting to access RAM mapped as secure in EL2.
Signed-off-by Marek Vasut <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 8/10 arm: imx: imx8m: Define trampoline location if PSCI provider
In reply to Marek VasutThe common code used to bring up secondary cores requires a final jump location to be stored in some sort of memory location, define this memory location to be the start of OCRAM, since it is available.
---
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Andrejs Cainikovs <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Manoj Sai <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Ricardo Salveti <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Ye Li <[email protected]>
--- arch/arm/include/asm/arch-imx8m/imx-regs.h | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm/include/asm/arch-imx8m/imx-regs.h +4 -0
@@ -91,6 +91,10 @@#define IOMUXC_GPR_GPR1_GPR_ENET_QOS_INTF_SEL_MASK 0x70000#define FEC_QUIRK_ENET_MAC +#ifdef CONFIG_ARMV8_PSCI /* Final jump location */ +#define CPU_RELEASE_ADDR 0x900000 +#endif +#define CAAM_ARB_BASE_ADDR (0x00100000)#define CAAM_ARB_END_ADDR (0x00107FFF)#define CAAM_IPS_BASE_ADDR (0x30900000)
Signature · 1 line
2.35.1
PATCH 8/10 arm: imx: imx8m: Define trampoline location if PSCI provider
Quoted 4 lines
The common code used to bring up secondary cores requires a final jump location to be stored in some sort of memory location, define this memory location to be the start of OCRAM, since it is available.
Signed-off-by Marek Vasut <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 9/10 arm: imx: imx8m: Program CSU and TZASC if PSCI provider
In reply to Marek VasutIn case U-Boot is the PSCI provider, it is necessary to correctly program CSU and TZASC registers. Those are poorly documented, so push in the correct values.
---
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Andrejs Cainikovs <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Manoj Sai <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Ricardo Salveti <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Ye Li <[email protected]>
--- arch/arm/include/asm/arch-imx8m/imx-regs.h | 1 + arch/arm/mach-imx/imx8m/soc.c | 25 ++++++++++++++++++++++ 2 files changed, 26 insertions(+)
arch/arm/include/asm/arch-imx8m/imx-regs.h +1 -0
@@ -31,6 +31,7 @@#define CCM_BASE_ADDR 0x30380000#define SRC_BASE_ADDR 0x30390000#define GPC_BASE_ADDR 0x303A0000 +#define CSU_BASE_ADDR 0x303E0000#define SYSCNT_RD_BASE_ADDR 0x306A0000#define SYSCNT_CMP_BASE_ADDR 0x306B0000
arch/arm/mach-imx/imx8m/soc.c +25 -0
@@ -561,6 +561,29 @@ static void imx8m_setup_snvs(void)writel (0xffffffff ,SNVS_BASE_ADDR +SNVS_LPSR ); } +static void imx8m_setup_csu_tzasc (void ) +{ +const uintptr_t tzasc_base[4 ] = { +0x301f0000 ,0x301f0000 ,0x301f0000 ,0x301f0000 + }; +int i, j; + +if (!IS_ENABLED (CONFIG_ARMV8_PSCI )) +return ; + +/* CSU */ +for (i =0 ; i <64 ; i++) +writel (0x00ff00ff , (void *)CSU_BASE_ADDR + (4 * i)); + +/* TZASC */ +for (j =0 ; j <4 ; j++) { +writel (0x77777777 , (void *)(tzasc_base[j])); +writel (0x77777777 , (void *)(tzasc_base[j]) +0x4 ); +for (i =0 ; i <=0x10 ; i +=4 ) +writel (0 , (void *)(tzasc_base[j]) +0x40 + i); + } +} +int arch_cpu_init (void ) {struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR ;
@@ -613,6 +636,8 @@ int arch_cpu_init(void)imx8m_setup_snvs (); +imx8m_setup_csu_tzasc (); +return 0 ; }
Signature · 1 line
2.35.1
PATCH 9/10 arm: imx: imx8m: Program CSU and TZASC if PSCI provider
Quoted 4 lines
In case U-Boot is the PSCI provider, it is necessary to correctly program CSU and TZASC registers. Those are poorly documented, so push in the correct values.
Signed-off-by Marek Vasut <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 10/10 arm: imx: imx8m: Add basic PSCI provider implementation
In reply to Marek VasutImplement basic PSCI provider to let OS turn CPU cores off and on, power off and restart the system and determine PSCI version. This is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following Kconfig options:
# CONFIG_PSCI_RESET is not set
CONFIG_ARMV8_MULTIENTRY=y
CONFIG_ARMV8_SET_SMPEN=y CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y CONFIG_ARMV8_EA_EL3_FIRST=y
CONFIG_ARMV8_PSCI=y
CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4 CONFIG_ARMV8_SECURE_BASE=0x970000
CONFIG_ARM_SMCCC=y
CONFIG_SYS_HAS_ARMV8_SECURE_BASE=y
---
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Andrejs Cainikovs <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Manoj Sai <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Ricardo Salveti <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Ye Li <[email protected]>
--- arch/arm/mach-imx/imx8m/Kconfig | 8 + arch/arm/mach-imx/imx8m/Makefile | 1 + arch/arm/mach-imx/imx8m/psci.c | 288 +++++++++++++++++++++++++++++++ 3 files changed, 297 insertions(+) create mode 100644 arch/arm/mach-imx/imx8m/psci.c
arch/arm/mach-imx/imx8m/Kconfig +8 -0
@@ -27,6 +27,14 @@ config IMX8MP config SYS_SOC default "imx8m" +config SYS_HAS_ARMV8_SECURE_BASE + bool "Enable secure address for PSCI image" + depends on ARMV8_PSCI + help + PSCI image can be re-located to secure RAM. + If enabled, please also define the value for ARMV8_SECURE_BASE, + for i.MX8M, it could be some address in OCRAM. + choice prompt "NXP i.MX8M board select" optional
arch/arm/mach-imx/imx8m/Makefile +1 -0
@@ -4,5 +4,6 @@ obj-y += lowlevel_init.o obj-y += clock_slice.o soc.o +obj-$(CONFIG_ARMV8_PSCI) += psci.o obj-$(CONFIG_IMX8MQ) += clock_imx8mq.o obj-$(CONFIG_IMX8MM)$(CONFIG_IMX8MN)$(CONFIG_IMX8MP) += clock_imx8mm.o
arch/arm/mach-imx/imx8m/psci.c new file +288 -0
288 lines not on this page · raw message
Signature · 1 line
2.35.1
Re: [PATCH 10/10] arm: imx: imx8m: Add basic PSCI provider implementation
Quoted 5 lines · Marek Vasut
Implement basic PSCI provider to let OS turn CPU cores off and on, power off and restart the system and determine PSCI version. This is sufficient to remove the need for the ATF BL31 blob altogether.
Quoted 9 lines
To make use of this functionality, active the following
Kconfigoptions:
#CONFIG_PSCI_RESETis not set
CONFIG_ARMV8_MULTIENTRY=y
CONFIG_ARMV8_SET_SMPEN=yCONFIG_ARMV8_SPL_EXCEPTION_VECTORS=yCONFIG_ARMV8_EA_EL3_FIRST=y
CONFIG_ARMV8_PSCI=y
CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4CONFIG_ARMV8_SECURE_BASE=0x970000
I am guessing 0x970000 was for the 8MP based on the previous location
of ATF. Is that true? If that's the case, can I assume that this
address would be 0x910000, 0x920000 and 0x960000 for the imx8mq, imx8mm and imx8mn respectively?
Quoted 354 lines
CONFIG_ARM_SMCCC=y
CONFIG_SYS_HAS_ARMV8_SECURE_BASE=ySigned-off-by Marek Vasut <[email protected]>---
Cc: "Ariel D'Alessandro" <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Cc: Adam Ford <[email protected]>
Cc: Andrejs Cainikovs <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Manoj Sai <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Ricardo Salveti <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Ye Li <[email protected]>--- arch/arm/mach-imx/imx8m/Kconfig | 8 + arch/arm/mach-imx/imx8m/Makefile | 1 + arch/arm/mach-imx/imx8m/psci.c | 288 +++++++++++++++++++++++++++++++ 3 files changed, 297 insertions(+) create mode 100644 arch/arm/mach-imx/imx8m/psci.carch/arm/mach-imx/imx8m/Kconfig +8
-0@@ -27,6 +27,14 @@ config IMX8MP config SYS_SOC default "imx8m" +config SYS_HAS_ARMV8_SECURE_BASE + bool "Enable secure address for PSCI image" + depends on ARMV8_PSCI + help + PSCI image can be re-located to secure RAM. + If enabled, please also define the value for ARMV8_SECURE_BASE, + for i.MX8M, it could be some address in OCRAM. + choice prompt "NXP i.MX8M board select" optionalarch/arm/mach-imx/imx8m/Makefile +1
-0@@ -4,5 +4,6 @@ obj-y += lowlevel_init.o obj-y += clock_slice.o soc.o +obj-$(CONFIG_ARMV8_PSCI) += psci.o obj-$(CONFIG_IMX8MQ) += clock_imx8mq.o obj-$(CONFIG_IMX8MM)$(CONFIG_IMX8MN)$(CONFIG_IMX8MP) += clock_imx8mm.oarch/arm/mach-imx/imx8m/psci.c new file +288
-1@@ -0,0 +1,288 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* This file implements basic PSCI support for i.MX8M +* +* Copyright (C) 2022 Marek Vasut <[email protected]> +*/ +#include <asm/arch/imx-regs.h> +#include <asm/cache.h> +#include <asm/gic.h> +#include <asm/io.h> +#include <asm/psci.h> +#include <asm/secure.h> +#include <common.h> +#include <cpu_func.h> +#include <debug_uart.h> +#include <fsl_wdog.h> +#include <linux/bitops.h> + +#define SNVS_LPCR 0x38 +#define SNVS_LPCR_TOP BIT(6) +#define SNVS_LPCR_DP_EN BIT(5) +#define SNVS_LPCR_SRTC_ENV BIT(0) + +#define MPIDR_AFF0 GENMASK(7, 0) + +#define GPC_LPCR_A53_AD 0x4 +#define EN_Cn_WFI_PDN (cpu) BIT(((((cpu) & 1) * 2) + (((cpu) & 2) * 8))) +#define GPC_PGC_nCTRL (cpu) (0x800 + ((cpu) * 0x40)) +#define PGC_PCR BIT(0) +#define GPC_CPU_PGC_SW_PUP_REQ (IS_ENABLED(CONFIG_IMX8MP) ? 0xd0 : 0xf0) +#define COREn_A53_SW_PUP_REQ (cpu) BIT(cpu) + +#define SRC_A53RCR1 0x8 +#define A53_COREn_ENABLE (n) BIT(n) +#define SRC_GPR (n) (0x74 + ((n) * 4)) + +/* +* Helper code +*/ +static u8 psci_state[CONFIG_ARMV8_PSCI_NR_CPUS] __secure_data = { +PSCI_AFFINITY_LEVEL_ON , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF , +PSCI_AFFINITY_LEVEL_OFF +}; + +int psci_update_dt (void *fdt) +{ +return 0 ; +} + +__secure static void psci_set_state(int cpu, u8 state) +{ + psci_state[cpu] = state; +dsb (); +isb (); +} + +__secure static s32 psci_cpu_on_validate_mpidr(u64 mpidr, u32 *cpu) +{ + *cpu = mpidr &MPIDR_AFF0 ; + +if (mpidr & ~MPIDR_AFF0 ) +return ARM_PSCI_RET_INVAL ; + +if (*cpu >=CONFIG_ARMV8_PSCI_NR_CPUS ) +return ARM_PSCI_RET_INVAL ; + +if (psci_state[*cpu] ==PSCI_AFFINITY_LEVEL_ON ) +return ARM_PSCI_RET_ALREADY_ON ; + +if (psci_state[*cpu] ==PSCI_AFFINITY_LEVEL_ON_PENDING ) +return ARM_PSCI_RET_ON_PENDING ; + +return ARM_PSCI_RET_SUCCESS ; +} + +__secure static void psci_cpu_on_write_entry_point(const u32 cpu, u64 entry_point) +{ +const u64 ep =CONFIG_SPL_TEXT_BASE ; + +/* Trampoline target */ +writeq (entry_point,CPU_RELEASE_ADDR ); +/* RVBAR address HI */ +writel ((u32)(ep >>24 ) &0xffff , + (void *)SRC_BASE_ADDR +SRC_GPR (cpu *2 )); +/* RVBAR address LO */ +writel ((u32)(ep >>2 ) &0x3fffff , + (void *)SRC_BASE_ADDR +SRC_GPR (cpu *2 +1 )); +} + +__secure static void psci_cpu_on_power_on(const u32 cpu) +{ +int i; + +clrbits_le32 ((void *)GPC_BASE_ADDR +GPC_LPCR_A53_AD ,EN_Cn_WFI_PDN (cpu)); +clrbits_le32 ((void *)SRC_BASE_ADDR +SRC_A53RCR1 ,A53_COREn_ENABLE (cpu)); +setbits_le32 ((void *)GPC_BASE_ADDR +GPC_PGC_nCTRL (cpu),PGC_PCR ); +setbits_le32 ((void *)GPC_BASE_ADDR +GPC_CPU_PGC_SW_PUP_REQ ,COREn_A53_SW_PUP_REQ (cpu)); + +/* If we fail here, the core gets power cycled, hang is OK */ +while (readl (GPC_BASE_ADDR +GPC_CPU_PGC_SW_PUP_REQ ) &COREn_A53_SW_PUP_REQ (cpu)) + ; + +clrbits_le32 ((void *)GPC_BASE_ADDR +GPC_PGC_nCTRL (cpu),PGC_PCR ); +setbits_le32 ((void *)SRC_BASE_ADDR +SRC_A53RCR1 ,A53_COREn_ENABLE (cpu)); + +/* Give the core a bit of time to boot and start executing code */ +for (i =0 ; i <100000 ; i++) + asmvolatile ("nop" ); +} + +__secure static void psci_cpu_on_power_off(const u32 cpu) +{ +setbits_le32 ((void *)GPC_BASE_ADDR +GPC_LPCR_A53_AD ,EN_Cn_WFI_PDN (cpu)); +setbits_le32 ((void *)GPC_BASE_ADDR +GPC_PGC_nCTRL (cpu),PGC_PCR ); +} + +/* +* Common PSCI code +*/ +/* Return supported PSCI version */ +__secure u32 psci_version(void) +{ +return ARM_PSCI_VER_1_0 ; +} + +/* +* 64bit PSCI code +*/ +__secure s32 psci_cpu_on_64(u32 __always_unused function_id, u64 mpidr, +u64 entry_point_address,u64 context_id) +{ +u32 cpu =0 ; +int ret; + + ret =psci_cpu_on_validate_mpidr (mpidr, &cpu); +if (ret !=ARM_PSCI_RET_SUCCESS ) +return ret; + +psci_cpu_on_write_entry_point (cpu, entry_point_address); + +psci_set_state (cpu,PSCI_AFFINITY_LEVEL_ON ); + +psci_cpu_on_power_on (cpu); + +smp_kick_all_cpus (); + +return ARM_PSCI_RET_SUCCESS ; +} + +__secure s32 psci_affinity_info_64(u32 __always_unused function_id, +u64 target_affinity,u32 lowest_affinity_level) +{ +u32 cpu = target_affinity &MPIDR_AFF0 ; + +if (lowest_affinity_level >0 ) +return ARM_PSCI_RET_INVAL ; + +if (target_affinity & ~MPIDR_AFF0 ) +return ARM_PSCI_RET_INVAL ; + +if (cpu >=CONFIG_ARMV8_PSCI_NR_CPUS ) +return ARM_PSCI_RET_INVAL ; + +return psci_state[cpu]; +} + +__secure s32 psci_system_reset2_64(u32 __always_unused function_id, +u32 reset_type,u64 cookie) +{ +psci_system_reset (); +return 0 ;/* Not reached */ +} + +/* +* 32bit PSCI code +*/ +__secure s32 psci_affinity_info(u32 __always_unused function_id, +u32 target_affinity,u32 lowest_affinity_level) +{ +return psci_affinity_info_64 (function_id, target_affinity, lowest_affinity_level); +} + +__secure s32 psci_cpu_on(u32 __always_unused function_id, u32 mpidr, +u32 entry_point_address,u32 context_id) +{ +return psci_cpu_on_64 (function_id, mpidr, entry_point_address, context_id); +} + +__secure s32 psci_cpu_off(void) +{ +u32 cpu =psci_get_cpu_id (); + +psci_cpu_on_power_off (cpu); +psci_set_state (cpu,PSCI_AFFINITY_LEVEL_OFF ); + +while (1 ) +wfi (); +} + +__secure u32 psci_migrate_info_type(void) +{ +/* Trusted OS is either not present or does not require migration */ +return 2 ; +} + +__secure void psci_system_reset(void) +{ +struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR ; +bool ext_reset = true; + +u16 wcr =WCR_WDE ; + +if (ext_reset) + wcr |=WCR_SRS ;/* do not assert internal reset */ +else + wcr |=WCR_WDA ;/* do not assert external reset */ + +/* Write 3 times to ensure it works, due to IMX6Q errata ERR004346 */ +writew (wcr, &wdog->wcr); +writew (wcr, &wdog->wcr); +writew (wcr, &wdog->wcr); + +while (1 ) +wfi (); +} + +__secure void psci_system_off(void) +{ +writel (SNVS_LPCR_TOP |SNVS_LPCR_DP_EN |SNVS_LPCR_SRTC_ENV , +SNVS_BASE_ADDR +SNVS_LPCR ); + +while (1 ) +wfi (); +} + +/* +* PSCI jump table +*/ +__secure s32 psci_features(u32 __always_unused function_id, u32 psci_fid) +{ +switch (psci_fid) { +case ARM_PSCI_0_2_FN_PSCI_VERSION : +case ARM_PSCI_0_2_FN_CPU_OFF : +case ARM_PSCI_0_2_FN_CPU_ON : +case ARM_PSCI_0_2_FN_AFFINITY_INFO : +case ARM_PSCI_0_2_FN_MIGRATE_INFO_TYPE : +case ARM_PSCI_0_2_FN_SYSTEM_OFF : +case ARM_PSCI_0_2_FN_SYSTEM_RESET : +case ARM_PSCI_0_2_FN64_CPU_ON : +case ARM_PSCI_0_2_FN64_AFFINITY_INFO : + +/* PSCI 1.0 interface */ +case ARM_PSCI_1_0_FN_PSCI_FEATURES : + +/* PSCI 1.1 interface */ +case ARM_PSCI_1_1_FN64_SYSTEM_RESET2 : +return 0x0 ; + +/* +* Not implemented: +* ARM_PSCI_0_2_FN_CPU_SUSPEND +* ARM_PSCI_1_0_FN_CPU_FREEZE +* ARM_PSCI_1_0_FN_CPU_DEFAULT_SUSPEND +* ARM_PSCI_1_0_FN_NODE_HW_STATE +* ARM_PSCI_1_0_FN_SYSTEM_SUSPEND +* ARM_PSCI_1_0_FN_SET_SUSPEND_MODE +* ARM_PSCI_1_0_FN_STAT_RESIDENCY +* ARM_PSCI_1_0_FN_STAT_COUNT +* ARM_PSCI_0_2_FN64_CPU_SUSPEND +* ARM_PSCI_1_0_FN64_CPU_DEFAULT_SUSPEND +* ARM_PSCI_1_0_FN64_NODE_HW_STATE +* ARM_PSCI_1_0_FN64_SYSTEM_SUSPEND +* ARM_PSCI_1_0_FN64_STAT_RESIDENCY +* ARM_PSCI_1_0_FN64_STAT_COUNT +*/ + +/* Not required, ARM_PSCI_0_2_FN_MIGRATE_INFO_TYPE returns 2 */ +case ARM_PSCI_0_2_FN_MIGRATE : +case ARM_PSCI_0_2_FN64_MIGRATE : +/* Not required */ +case ARM_PSCI_0_2_FN_MIGRATE_INFO_UP_CPU : +case ARM_PSCI_0_2_FN64_MIGRATE_INFO_UP_CPU : +default : +return ARM_PSCI_RET_NI ; + } +} --2.35.1
Re: [PATCH 10/10] arm: imx: imx8m: Add basic PSCI provider implementation
Quoted 16 lines · Adam Ford
Quoted 6 lines · Marek Vasut
Implement basic PSCI provider to let OS turn CPU cores off and on, power off and restart the system and determine PSCI version. This is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following
Kconfigoptions:Quoted 8 lines
# CONFIG_PSCI_RESET is not set CONFIG_ARMV8_MULTIENTRY=y CONFIG_ARMV8_SET_SMPEN=y CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y CONFIG_ARMV8_EA_EL3_FIRST=y CONFIG_ARMV8_PSCI=y CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4 CONFIG_ARMV8_SECURE_BASE=0x970000
Quoted 4 lines
I am guessing
0x970000was for the 8MP based on the previous location
of ATF. Is that true? If that's the case, can I assume that this
address would be0x910000,0x920000and0x960000for the imx8mq, imx8mm and imx8mn respectively?
It was for MX8MP, but you can pick whichever address you want, since it is U-Boot that installs the SMC handlers, you are no longer forced to somehow try and accommodate custom not well fitting load address picked by some 3rd party binary blob.
Re: [PATCH 10/10] arm: imx: imx8m: Add basic PSCI provider implementation
Quoted 23 lines · Marek Vasut
Quoted 16 lines · Adam Ford
Quoted 6 lines · Marek Vasut
Implement basic PSCI provider to let OS turn CPU cores off and on, power off and restart the system and determine PSCI version. This is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following
Kconfigoptions:Quoted 8 lines
# CONFIG_PSCI_RESET is not set CONFIG_ARMV8_MULTIENTRY=y CONFIG_ARMV8_SET_SMPEN=y CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y CONFIG_ARMV8_EA_EL3_FIRST=y CONFIG_ARMV8_PSCI=y CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4 CONFIG_ARMV8_SECURE_BASE=0x970000Quoted 4 lines
I am guessing
0x970000was for the 8MP based on the previous location
of ATF. Is that true? If that's the case, can I assume that this
address would be0x910000,0x920000and0x960000for the imx8mq, imx8mm and imx8mn respectively?
Quoted 4 lines
It was for MX8MP, but you can pick whichever address you want, since it is U-Boot that installs the SMC handlers, you are no longer forced to somehow try and accommodate custom not well fitting load address picked by some 3rd party binary blob.
I patched U-Boot's master with this series and I tried it on imx8mn_beacon and imx8mm_beacon without success. I never even saw the SPL message. I tried to focus on the Nano since the boot ROM in that one is more similar to that of the 8mp, but the behaviour was similar to that of the Nano. Are there any dependencies or should I have used a specific starting branch?
adam
Re: [PATCH 10/10] arm: imx: imx8m: Add basic PSCI provider implementation
Quoted 29 lines · Adam Ford
Quoted 23 lines · Marek Vasut
Quoted 16 lines · Adam Ford
Quoted 6 lines · Marek Vasut
Implement basic PSCI provider to let OS turn CPU cores off and on, power off and restart the system and determine PSCI version. This is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following
Kconfigoptions:Quoted 8 lines
# CONFIG_PSCI_RESET is not set CONFIG_ARMV8_MULTIENTRY=y CONFIG_ARMV8_SET_SMPEN=y CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y CONFIG_ARMV8_EA_EL3_FIRST=y CONFIG_ARMV8_PSCI=y CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4 CONFIG_ARMV8_SECURE_BASE=0x970000Quoted 4 lines
I am guessing
0x970000was for the 8MP based on the previous location
of ATF. Is that true? If that's the case, can I assume that this
address would be0x910000,0x920000and0x960000for the imx8mq, imx8mm and imx8mn respectively?Quoted 4 lines
It was for MX8MP, but you can pick whichever address you want, since it is U-Boot that installs the SMC handlers, you are no longer forced to somehow try and accommodate custom not well fitting load address picked by some 3rd party binary blob.
Quoted 6 lines
I patched U-Boot's master with this series and I tried it on
imx8mn_beaconandimx8mm_beaconwithout success. I never even saw the SPL message. I tried to focus on the Nano since the boot ROM in that one is more similar to that of the 8mp, but the behaviour was similar to that of the Nano. Are there any dependencies or should I have used a specific starting branch?
Nope . But if you don't even see output from SPL, that's where I would start looking. Do you see output from SPL without this series ? Note that bulk of this series content applies to U-Boot proper, not SPL so far.
Re: [PATCH 10/10] arm: imx: imx8m: Add basic PSCI provider implementation
Quoted 38 lines · Marek Vasut
Quoted 29 lines · Adam Ford
Quoted 23 lines · Marek Vasut
Quoted 16 lines · Adam Ford
Quoted 6 lines · Marek Vasut
Implement basic PSCI provider to let OS turn CPU cores off and on, power off and restart the system and determine PSCI version. This is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following
Kconfigoptions:Quoted 8 lines
# CONFIG_PSCI_RESET is not set CONFIG_ARMV8_MULTIENTRY=y CONFIG_ARMV8_SET_SMPEN=y CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y CONFIG_ARMV8_EA_EL3_FIRST=y CONFIG_ARMV8_PSCI=y CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4 CONFIG_ARMV8_SECURE_BASE=0x970000Quoted 4 lines
I am guessing
0x970000was for the 8MP based on the previous location
of ATF. Is that true? If that's the case, can I assume that this
address would be0x910000,0x920000and0x960000for the imx8mq, imx8mm and imx8mn respectively?Quoted 4 lines
It was for MX8MP, but you can pick whichever address you want, since it is U-Boot that installs the SMC handlers, you are no longer forced to somehow try and accommodate custom not well fitting load address picked by some 3rd party binary blob.
Quoted 6 lines
I patched U-Boot's master with this series and I tried it on
imx8mn_beaconandimx8mm_beaconwithout success. I never even saw the SPL message. I tried to focus on the Nano since the boot ROM in that one is more similar to that of the 8mp, but the behaviour was similar to that of the Nano. Are there any dependencies or should I have used a specific starting branch?
Quoted 3 lines
Nope . But if you don't even see output from SPL, that's where I would start looking. Do you see output from SPL without this series ? Note that bulk of this series content applies to U-Boot proper, not SPL so far.
Without the patch series the generated flash.bin file booted both the Mini and the Nano just fine. I have a pending 8m plus that I can also try, since that is what you used. I just wanted to make sure I was starting from the right place before I went too far with it.
adam
Re: [PATCH 10/10] arm: imx: imx8m: Add basic PSCI provider implementation
Quoted 39 lines · Adam Ford
Quoted 38 lines · Marek Vasut
Quoted 35 lines · Adam Ford
Quoted 23 lines · Marek Vasut
Quoted 16 lines · Adam Ford
Quoted 6 lines · Marek Vasut
Implement basic PSCI provider to let OS turn CPU cores off and on, power off and restart the system and determine PSCI version. This is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following
Kconfigoptions:Quoted 8 lines
# CONFIG_PSCI_RESET is not set CONFIG_ARMV8_MULTIENTRY=y CONFIG_ARMV8_SET_SMPEN=y CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y CONFIG_ARMV8_EA_EL3_FIRST=y CONFIG_ARMV8_PSCI=y CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4 CONFIG_ARMV8_SECURE_BASE=0x970000Quoted 4 lines
I am guessing 0x970000 was for the 8MP based on the previous locationof ATF. Is that true? If that's the case, can I assume that this
address would be0x910000,0x920000and0x960000for the imx8mq, imx8mm and imx8mn respectively?Quoted 4 lines
It was for MX8MP, but you can pick whichever address you want, since it is U-Boot that installs the SMC handlers, you are no longer forced to somehow try and accommodate custom not well fitting load address picked by some 3rd party binary blob.
I patched U-Boot's master with this series and I tried it on
imx8mn_beaconandimx8mm_beaconwithout success. I never even saw the SPL message. I tried to focus on the Nano since the boot ROM in that one is more similar to that of the 8mp, but the behaviour was similar to that of the Nano. Are there any dependencies or should I have used a specific starting branch?
Quoted 8 lines
Quoted 3 lines
Nope . But if you don't even see output from SPL, that's where I would start looking. Do you see output from SPL without this series ? Note that bulk of this series content applies to U-Boot proper, not SPL so far.
Without the patch series the generated flash.bin file booted both the Mini and the Nano just fine. I have a pending 8m plus that I can also try, since that is what you used. I just wanted to make sure I was starting from the right place before I went too far with it.
Try and drop
[PATCH 09/10] arm: imx: imx8m: Program CSU and TZASC if PSCI provider
does SPL start then ?
I plan to try this on Nano at some point this month too.
Re: [PATCH 10/10] arm: imx: imx8m: Add basic PSCI provider implementation
Quoted 50 lines · Marek Vasut
Quoted 39 lines · Adam Ford
Quoted 38 lines · Marek Vasut
Quoted 35 lines · Adam Ford
Quoted 23 lines · Marek Vasut
Quoted 16 lines · Adam Ford
Quoted 6 lines · Marek Vasut
Implement basic PSCI provider to let OS turn CPU cores off and on, power off and restart the system and determine PSCI version. This is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following
Kconfigoptions:Quoted 8 lines
# CONFIG_PSCI_RESET is not set CONFIG_ARMV8_MULTIENTRY=y CONFIG_ARMV8_SET_SMPEN=y CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y CONFIG_ARMV8_EA_EL3_FIRST=y CONFIG_ARMV8_PSCI=y CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4 CONFIG_ARMV8_SECURE_BASE=0x970000Quoted 4 lines
I am guessing 0x970000 was for the 8MP based on the previous locationof ATF. Is that true? If that's the case, can I assume that this
address would be0x910000,0x920000and0x960000for the imx8mq, imx8mm and imx8mn respectively?Quoted 4 lines
It was for MX8MP, but you can pick whichever address you want, since it is U-Boot that installs the SMC handlers, you are no longer forced to somehow try and accommodate custom not well fitting load address picked by some 3rd party binary blob.
I patched U-Boot's master with this series and I tried it on
imx8mn_beaconandimx8mm_beaconwithout success. I never even saw the SPL message. I tried to focus on the Nano since the boot ROM in that one is more similar to that of the 8mp, but the behaviour was similar to that of the Nano. Are there any dependencies or should I have used a specific starting branch?Quoted 8 lines
Quoted 3 lines
Nope . But if you don't even see output from SPL, that's where I would start looking. Do you see output from SPL without this series ? Note that bulk of this series content applies to U-Boot proper, not SPL so far.
Without the patch series the generated flash.bin file booted both the Mini and the Nano just fine. I have a pending 8m plus that I can also try, since that is what you used. I just wanted to make sure I was starting from the right place before I went too far with it.
Quoted 5 lines
Try and drop
[PATCH 09/10] arm: imx: imx8m: Program CSU and TZASC if PSCI provider
does SPL start then ?
I reverted 9/19 without success either. I'll try to do a git bisect to see if I can narrow it down. I might see if my employer will let me borrow a debugger. Debugging SPL is a bit challenging due to the relocation step, but I am not convinced I am geting that far since I get no text output at all.
Quoted 2 lines
I plan to try this on Nano at some point this month too.
I'll let you know my findings when I get some more time to test this.
adam
Re: [PATCH 10/10] arm: imx: imx8m: Add basic PSCI provider implementation
Quoted 55 lines · Adam Ford
Quoted 54 lines · Marek Vasut
Quoted 39 lines · Adam Ford
Quoted 38 lines · Marek Vasut
Quoted 35 lines · Adam Ford
Quoted 23 lines · Marek Vasut
Quoted 16 lines · Adam Ford
Quoted 6 lines · Marek Vasut
Implement basic PSCI provider to let OS turn CPU cores off and on, power off and restart the system and determine PSCI version. This is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following
Kconfigoptions:Quoted 8 lines
# CONFIG_PSCI_RESET is not set CONFIG_ARMV8_MULTIENTRY=y CONFIG_ARMV8_SET_SMPEN=y CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y CONFIG_ARMV8_EA_EL3_FIRST=y CONFIG_ARMV8_PSCI=y CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4 CONFIG_ARMV8_SECURE_BASE=0x970000Quoted 4 lines
I am guessing 0x970000 was for the 8MP based on the previous locationof ATF. Is that true? If that's the case, can I assume that this
address would be0x910000,0x920000and0x960000for the imx8mq, imx8mm and imx8mn respectively?Quoted 4 lines
It was for MX8MP, but you can pick whichever address you want, since it is U-Boot that installs the SMC handlers, you are no longer forced to somehow try and accommodate custom not well fitting load address picked by some 3rd party binary blob.
I patched U-Boot's master with this series and I tried it on
imx8mn_beaconandimx8mm_beaconwithout success. I never even saw the SPL message. I tried to focus on the Nano since the boot ROM in that one is more similar to that of the 8mp, but the behaviour was similar to that of the Nano. Are there any dependencies or should I have used a specific starting branch?Quoted 8 lines
Quoted 3 lines
Nope . But if you don't even see output from SPL, that's where I would start looking. Do you see output from SPL without this series ? Note that bulk of this series content applies to U-Boot proper, not SPL so far.
Without the patch series the generated flash.bin file booted both the Mini and the Nano just fine. I have a pending 8m plus that I can also try, since that is what you used. I just wanted to make sure I was starting from the right place before I went too far with it.
Try and drop
[PATCH 09/10] arm: imx: imx8m: Program CSU and TZASC if PSCI provider
Quoted 7 lines
Quoted 1 line
does SPL start then ?
I reverted 9/19 without success either. I'll try to do a git bisect to see if I can narrow it down. I might see if my employer will let me borrow a debugger. Debugging SPL is a bit challenging due to the relocation step, but I am not convinced I am geting that far since I get no text output at all.
Hmmmmm, did you tweak the CONFIG_ARMV8_SECURE_BASE ? Are you sure your setting is within valid OCRAM address range ? I think the MX8MN OCRAM is smaller than the MX8MP one, but I might be wrong.
Bisect looks like the best option now. You can start by scrubbing the custom config options and see if the result still boots with the blob bl31.bin . If it does, it is somehow related to the newly enabled code. It has to be related to something very early though, something which is triggered before the UART init. Do you use DM_SERIAL in SPL ?
Quoted 3 lines
Quoted 1 line
I plan to try this on Nano at some point this month too.
I'll let you know my findings when I get some more time to test this.
Thanks
PATCH 10/10 arm: imx: imx8m: Add basic PSCI provider implementation
In reply to Marek VasutQuoted 14 lines
Implement basic PSCI provider to let OS turn CPU cores off and on, power off and restart the system and determine PSCI version. This is sufficient to remove the need for the ATF BL31 blob altogether. To make use of this functionality, active the following
Kconfigoptions:
#CONFIG_PSCI_RESETis not set
CONFIG_ARMV8_MULTIENTRY=y
CONFIG_ARMV8_SET_SMPEN=yCONFIG_ARMV8_SPL_EXCEPTION_VECTORS=yCONFIG_ARMV8_EA_EL3_FIRST=y
CONFIG_ARMV8_PSCI=y
CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4CONFIG_ARMV8_SECURE_BASE=0x970000
CONFIG_ARM_SMCCC=y
CONFIG_SYS_HAS_ARMV8_SECURE_BASE=y
Quoted 1 line
Signed-off-by Marek Vasut <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 1/10 arm: psci: Add PSCI v1.1 macro
In reply to Marek VasutQuoted 2 lines
Add macro representing the PSCI v1.1 .
Signed-off-by Marek Vasut <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================