Add minimal boot support for IPQ9574
Subsystems (10)
v5 cover Add minimal boot support for IPQ9574
The IPQ9574 is Qualcomm's 802.11ax SoC for Routers, Gateways and Access Points
This series adds minimal board boot support for ipq9574-al02-c7 board
V4 can be found at https://lore.kernel.org/linux-arm-kernel/[email protected]/
Change log is added to the respective patches
Devi Priya (7):
dt-bindings: clock: Add ipq9574 clock and reset definitions
clk: qcom: Add Global Clock Controller driver for IPQ9574
dt-bindings: pinctrl: qcom: Add support for IPQ9574
pinctrl: qcom: Add IPQ9574 pinctrl driver
dt-bindings: arm: qcom: Add ipq9574 compatible
arm64: dts: qcom: Add ipq9574 SoC and AL02 board support
arm64: defconfig: Enable IPQ9574 SoC base configs
.../devicetree/bindings/arm/qcom.yaml | 7 + .../bindings/clock/qcom,ipq9574-gcc.yaml | 72 + .../bindings/pinctrl/qcom,ipq9574-tlmm.yaml | 137 + arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 84 + arch/arm64/boot/dts/qcom/ipq9574.dtsi | 278 ++ arch/arm64/configs/defconfig | 2 + drivers/clk/qcom/Kconfig | 8 + drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/gcc-ipq9574.c | 4302 +++++++++++++++++ drivers/pinctrl/qcom/Kconfig | 11 + drivers/pinctrl/qcom/Makefile | 1 + drivers/pinctrl/qcom/pinctrl-ipq9574.c | 861 ++++ include/dt-bindings/clock/qcom,ipq9574-gcc.h | 213 + include/dt-bindings/reset/qcom,ipq9574-gcc.h | 164 + 15 files changed, 6142 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq9574-tlmm.yaml create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi create mode 100644 drivers/clk/qcom/gcc-ipq9574.c create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq9574.c create mode 100644 include/dt-bindings/clock/qcom,ipq9574-gcc.h create mode 100644 include/dt-bindings/reset/qcom,ipq9574-gcc.h
base-commit: ea4dabbb4ad7eb52632a2ca0b8f89f0ea7c55dcf
Signature · 1 line
2.17.1
PATCH v5 1/7 dt-bindings: clock: Add ipq9574 clock and reset definitions
Add clock and reset ID definitions for ipq9574
---
Changes in V5:
- No changes
.../bindings/clock/qcom,ipq9574-gcc.yaml | 72 ++++++ include/dt-bindings/clock/qcom,ipq9574-gcc.h | 213 ++++++++++++++++++ include/dt-bindings/reset/qcom,ipq9574-gcc.h | 164 ++++++++++++++ 3 files changed, 449 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml create mode 100644 include/dt-bindings/clock/qcom,ipq9574-gcc.h create mode 100644 include/dt-bindings/reset/qcom,ipq9574-gcc.h
Documentation/devicetree/bindings/clock/qcom,ipq9574-gcc.yaml new file +72 -0
@@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/qcom,ipq9574-gcc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Global Clock & Reset Controller on IPQ9574 + +maintainers: + - Anusha Rao <[email protected]> + +description: | + Qualcomm global clock control module provides the clocks, resets and power + domains on IPQ9574 + + See also:: + include/dt-bindings/clock/qcom,ipq9574-gcc.h + include/dt-bindings/reset/qcom,ipq9574-gcc.h + +properties: + compatible: + const: qcom,ipq9574-gcc + + clocks: + items: + - description: Board XO source + - description: Sleep clock source + - description: Bias PLL ubi clock source + - description: PCIE30 PHY0 pipe clock source + - description: PCIE30 PHY1 pipe clock source + - description: PCIE30 PHY2 pipe clock source + - description: PCIE30 PHY3 pipe clock source + - description: USB3 PHY pipe clock source + + clock-names: + items: + - const: xo + - const: sleep_clk + - const: bias_pll_ubi_nc_clk + - const: pcie30_phy0_pipe_clk + - const: pcie30_phy1_pipe_clk + - const: pcie30_phy2_pipe_clk + - const: pcie30_phy3_pipe_clk + - const: usb3phy_0_cc_pipe_clk + +required: + - compatible + - clocks + +allOf: + - $ref: qcom,gcc.yaml# + +unevaluatedProperties: false + +examples: + - | + clock-controller@1800000 { + compatible = "qcom,ipq9574-gcc"; + reg = <0x01800000 0x80000>; + clocks = <&xo_board_clk>, + <&sleep_clk>, + <&bias_pll_ubi_nc_clk>, + <&pcie30_phy0_pipe_clk>, + <&pcie30_phy1_pipe_clk>, + <&pcie30_phy2_pipe_clk>, + <&pcie30_phy3_pipe_clk>, + <&usb3phy_0_cc_pipe_clk>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; +...
include/dt-bindings/clock/qcom,ipq9574-gcc.h new file +213 -0
213 lines not on this page · raw message
include/dt-bindings/reset/qcom,ipq9574-gcc.h new file +164 -0
164 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v5 2/7 clk: qcom: Add Global Clock Controller driver for IPQ9574
In reply to Devi PriyaAdd Global Clock Controller (GCC) driver for ipq9574 based devices
---
Changes in V5:
- Added clk_rcg2_floor_ops in place of clk_rcg2_ops for sdcc1 clock to fix the MMC overclocking warnings
drivers/clk/qcom/Kconfig | 8 + drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/gcc-ipq9574.c | 4302 ++++++++++++++++++++++++++++++++ 3 files changed, 4311 insertions(+) create mode 100644 drivers/clk/qcom/gcc-ipq9574.c
drivers/clk/qcom/Kconfig +8 -0
@@ -173,6 +173,14 @@ config IPQ_GCC_8074 i2c, USB, SD/eMMC, etc. Select this for the root clock of ipq8074. +config IPQ_GCC_9574 + tristate "IPQ9574 Global Clock Controller" + help + Support for global clock controller on ipq9574 devices. + Say Y if you want to use peripheral devices such as UART, SPI, + i2c, USB, SD/eMMC, etc. Select this for the root clock + of ipq9574. + config MSM_GCC_8660 tristate "MSM8660 Global Clock Controller" help
drivers/clk/qcom/Makefile +1 -0
@@ -27,6 +27,7 @@ obj-$(CONFIG_IPQ_GCC_4019) += gcc-ipq4019.o obj-$(CONFIG_IPQ_GCC_6018) += gcc-ipq6018.o obj-$(CONFIG_IPQ_GCC_806X) += gcc-ipq806x.o obj-$(CONFIG_IPQ_GCC_8074) += gcc-ipq8074.o +obj-$(CONFIG_IPQ_GCC_9574) += gcc-ipq9574.o obj-$(CONFIG_IPQ_LCC_806X) += lcc-ipq806x.o obj-$(CONFIG_MDM_GCC_9607) += gcc-mdm9607.o obj-$(CONFIG_MDM_GCC_9615) += gcc-mdm9615.o
drivers/clk/qcom/gcc-ipq9574.c new file +4302 -0
2,979 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
2.17.1
Part of the diff is not shown here. View the raw message.
PATCH v5 3/7 dt-bindings: pinctrl: qcom: Add support for IPQ9574
In reply to Devi PriyaAdd new binding document for pinctrl on IPQ9574
---
Changes in V5:
- No changes
.../bindings/pinctrl/qcom,ipq9574-tlmm.yaml | 137 ++++++++++++++++++ 1 file changed, 137 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq9574-tlmm.yaml
Documentation/devicetree/bindings/pinctrl/qcom,ipq9574-tlmm.yaml new file +137 -0
@@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq9574-tlmm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. IPQ9574 TLMM block + +maintainers: + - Bjorn Andersson <[email protected]> + - Krzysztof Kozlowski <[email protected]> + +description: + Top Level Mode Multiplexer pin controller in Qualcomm IPQ9574 SoC. + +properties: + compatible: + const: qcom,ipq9574-tlmm + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-controller: true + "#interrupt-cells": true + gpio-controller: true + "#gpio-cells": true + gpio-ranges: true + wakeup-parent: true + + gpio-reserved-ranges: + minItems: 1 + maxItems: 33 + + gpio-line-names: + maxItems: 65 + +patternProperties: + "-state$": + oneOf: + - $ref: "#/$defs/qcom-ipq9574-tlmm-state" + - patternProperties: + "-pins$": + $ref: "#/$defs/qcom-ipq9574-tlmm-state" + additionalProperties: false + +$defs: + qcom-ipq9574-tlmm-state: + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-5][0-9]|6[0-4])$" + - enum: [ qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2, qdsd_cmd, + qdsd_data0, qdsd_data1, qdsd_data2, qdsd_data3, sdc1_clk, + sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data ] + minItems: 1 + maxItems: 8 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + + enum: [ atest_char, atest_char0, atest_char1, atest_char2, atest_char3, + audio_pdm0, audio_pdm1, audio_pri, audio_sec, blsp0_spi, blsp0_uart, + blsp1_i2c, blsp1_spi, blsp1_uart, blsp2_i2c, blsp2_spi, + blsp2_uart, blsp3_i2c, blsp3_spi, blsp3_uart, blsp4_i2c, + blsp4_spi, blsp4_uart, blsp5_i2c, blsp5_uart, cri_trng0, + cri_trng1, cri_trng3, cxc0, cxc1, dbg_out, dwc_ddrphy, + gcc_plltest, gcc_tlmm, mac00, mac01, mac10, mac11, mdc, + mdio, pcie0_clk, pcie0_wake, pcie1_clk, pcie1_wake, pcie2_clk, + pcie2_wake, pcie3_clk, pcie3_wake, prng_rosc0, prng_rosc1, + prng_rosc2, prng_rosc3, pta1_0, pta1_1, pta1_2, pta20, pta21, + pwm00, pwm01, pwm02, pwm03, pwm04, pwm10, pwm11, pwm12, pwm13, + pwm14, pwm20, pwm21, pwm22, pwm23, pwm24, pwm30, pwm31, pwm32, + pwm33, qdss_cti_trig_in_a0, qdss_cti_trig_in_a1, qdss_cti_trig_in_b0, + qdss_cti_trig_in_b1, qdss_cti_trig_out_a0, qdss_cti_trig_out_a1, + qdss_cti_trig_out_b0, qdss_cti_trig_out_b1, qdss_traceclk_a, + qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, qdss_tracedata_a, + qdss_tracedata_b, qdss_tracedata_b, qspi_clk, qspi_cs, qspi_data, + rx0, rx1, sdc_clk, sdc_cmd, sdc_data, sdc_rclk, tsens_max, + wci20, wci21, wsa_swrm ] + + bias-pull-down: true + bias-pull-up: true + bias-disable: true + drive-strength: true + input-enable: true + output-high: true + output-low: true + + required: + - pins + + additionalProperties: false + +allOf: + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq9574-tlmm"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 65>; + + uart2-state { + pins = "gpio34", "gpio35"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-pull-down; + }; + };
Signature · 1 line
2.17.1
PATCH v5 4/7 pinctrl: qcom: Add IPQ9574 pinctrl driver
In reply to Devi PriyaAdd pinctrl definitions for the TLMM of IPQ9574
---
Changes in V5:
- No changes
drivers/pinctrl/qcom/Kconfig | 11 + drivers/pinctrl/qcom/Makefile | 1 + drivers/pinctrl/qcom/pinctrl-ipq9574.c | 861 +++++++++++++++++++++++++ 3 files changed, 873 insertions(+) create mode 100644 drivers/pinctrl/qcom/pinctrl-ipq9574.c
drivers/pinctrl/qcom/Kconfig +11 -0
@@ -70,6 +70,17 @@ config PINCTRL_IPQ6018 Qualcomm Technologies Inc. IPQ6018 platform. Select this for IPQ6018. +config PINCTRL_IPQ9574 + tristate "Qualcomm Technologies, Inc. IPQ9574 pin controller driver" + depends on OF + depends on ARM64 || COMPILE_TEST + depends on PINCTRL_MSM + help + This is the pinctrl, pinmux, pinconf and gpiolib driver for + the Qualcomm Technologies Inc. TLMM block found on the + Qualcomm Technologies Inc. IPQ9574 platform. Select this for + IPQ9574. + config PINCTRL_MSM8226 tristate "Qualcomm 8226 pin controller driver" depends on OF
drivers/pinctrl/qcom/Makefile +1 -0
@@ -7,6 +7,7 @@ obj-$(CONFIG_PINCTRL_IPQ4019) += pinctrl-ipq4019.o obj-$(CONFIG_PINCTRL_IPQ8064) += pinctrl-ipq8064.o obj-$(CONFIG_PINCTRL_IPQ8074) += pinctrl-ipq8074.o obj-$(CONFIG_PINCTRL_IPQ6018) += pinctrl-ipq6018.o +obj-$(CONFIG_PINCTRL_IPQ9574) += pinctrl-ipq9574.o obj-$(CONFIG_PINCTRL_MSM8226) += pinctrl-msm8226.o obj-$(CONFIG_PINCTRL_MSM8660) += pinctrl-msm8660.o obj-$(CONFIG_PINCTRL_MSM8960) += pinctrl-msm8960.o
drivers/pinctrl/qcom/pinctrl-ipq9574.c new file +861 -0
861 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v5 5/7 dt-bindings: arm: qcom: Add ipq9574 compatible
In reply to Devi PriyaDocument the new ipq9574 SoC/board device tree bindings
---
Changes in V5:
- No changes
Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++ 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/arm/qcom.yaml +7 -0
@@ -32,6 +32,7 @@ description: | ipq4018 ipq6018 ipq8074 + ipq9574 mdm9615 msm8226 msm8916
@@ -79,6 +80,7 @@ description: | The 'board' element must be one of the following strings: adp + ap-al02-c7 cdp cp01-c1 dragonboard
@@ -329,6 +331,11 @@ properties: - qcom,ipq8074-hk10-c2 - const: qcom,ipq8074 + - items: + - enum: + - qcom,ipq9574-ap-al02-c7 + - const: qcom,ipq9574 + - description: Sierra Wireless MangOH Green with WP8548 Module items: - const: swir,mangoh-green-wp8548
Signature · 1 line
2.17.1
PATCH v5 6/7 arm64: dts: qcom: Add ipq9574 SoC and AL02 board support
In reply to Devi PriyaAdd initial device tree support for Qualcomm IPQ9574 SoC and AL02 board
---
Changes in V5:
- Moved the below properties to the board dts
- mmc-ddr-1_8v
- mmc-hs200-1_8v
- mmc-hs400-1_8v
- mmc-hs400-enhanced-strobe
- max-frequency = <384000000>
- bus-width = <8>
arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts | 84 ++++++ arch/arm64/boot/dts/qcom/ipq9574.dtsi | 278 +++++++++++++++++++ 3 files changed, 363 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi
arch/arm64/boot/dts/qcom/Makefile +1 -0
@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c2.dtb +dtb-$(CONFIG_ARCH_QCOM) += ipq9574-al02-c7.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-acer-a1-724.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb
arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts new file +84 -0
84 lines not on this page · raw message
arch/arm64/boot/dts/qcom/ipq9574.dtsi new file +278 -0
278 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v5 7/7 arm64: defconfig: Enable IPQ9574 SoC base configs
In reply to Devi PriyaEnables clk & pinctrl related configs
---
Changes in V5:
- No changes
arch/arm64/configs/defconfig | 2 ++ 1 file changed, 2 insertions(+)
arch/arm64/configs/defconfig +2 -0
@@ -556,6 +556,7 @@ CONFIG_PINCTRL_IMX93=y CONFIG_PINCTRL_MSM=y CONFIG_PINCTRL_IPQ8074=y CONFIG_PINCTRL_IPQ6018=y +CONFIG_PINCTRL_IPQ9574=y CONFIG_PINCTRL_MSM8916=y CONFIG_PINCTRL_MSM8953=y CONFIG_PINCTRL_MSM8976=y
@@ -1131,6 +1132,7 @@ CONFIG_QCOM_CLK_SMD_RPM=y CONFIG_QCOM_CLK_RPMH=y CONFIG_IPQ_GCC_6018=y CONFIG_IPQ_GCC_8074=y +CONFIG_IPQ_GCC_9574=y CONFIG_MSM_GCC_8916=y CONFIG_MSM_GCC_8994=y CONFIG_MSM_MMCC_8996=y
Signature · 1 line
2.17.1
Re: [PATCH V5 7/7] arm64: defconfig: Enable IPQ9574 SoC base configs
Quoted 1 line · Devi Priya
Enables clk & pinctrl related configs
"for Qualcomm IPQ9574 SoC".
Because defconfig is for all sub-architectures, thus IPQ9574 is non-obvious for most of people.
With above:
Best regards,
Krzysztof
Re: [PATCH V5 7/7] arm64: defconfig: Enable IPQ9574 SoC base configs
Quoted 12 lines · Krzysztof Kozlowski
Quoted 1 line · Devi Priya
Enables clk & pinctrl related configs
"for Qualcomm IPQ9574 SoC".
Because defconfig is for all sub-architectures, thus IPQ9574 is non-obvious for most of people.Okay, got it
With above:
Reviewed-by Krzysztof Kozlowski <[email protected]>
Sure, Thank you!
Quoted 4 lines
Best regards,
Krzysztof
Best Regards,
Devi Priya