Add LVTS Thermal Architecture
Subsystems (3)
v13 cover Add LVTS Thermal Architecture
From: Balsam CHIHI <[email protected]>
The LVTS (Low Voltage Thermal Sensor) driver is capable of monitoring multiple hot points. For that, it contains 7 thermal control blocks dedicated to specific devices on the die. Each control block can handle up to 4 sensors.
The thermal controller supports several interrupts. One for the cold trip point, the hot trip point, the return to the normal trip point, and a specific programmable trip point to monitor the temperature dynamically.
The temperature measurement can be done in two ways, the immediate mode where the temperature read is instantaneous and the filtered mode where the controller uses, by configuration, an average of a set of values removing the minimum and the maximum.
Finally, it is composed of 2 finite-state machines responsible for the state of the temperature (cold, hot, hot 2 normal, hot hot), the triggering of the interrupts, and the monitoring of the temperature.
As requested, the thermal driver has been reworked to reduce the complexity of the code. At this time, the 4 little CPUs and the 4 big CPUs are supported by the thermal driver.They are described in a data structure and more devices can be added later. The calibration routine has been simplified also.
The series provide the following changes:
- Move the Mediatek drivers inside a dedicated folder as their number is increasing
- Add the DT bindings for the controller
- Add the efuse node for the mt8195
- The LVTS driver
- The thermal zones description in the DT
Changelog:
v13:
- Rebase on top of "thermal/linux-next" :
base-commit: a2c81dc59d41e92362ab7d41d0c15471ea50637d
- Fix coding style issues
- Remove "__init" from all functions
- Remove "lvts_ctrl_enable" and "lvts_ctrl_disable" wrappers
- Use "dev_err_probe" instead of "dev_dbg" in "lvts_probe"
- Fix subject prefix
- Add "mt8192" to dt-binding definition
- Change dt-binding license to "GPL-2.0-only OR BSD-2-Clause"
- Fix debugfs mutli-instance support
v12:
- Fix subject prefix
- Add dual licenses to dt-binding
- Rename "include/dt-bindings/thermal/mediatek-lvts.h" to "include/dt-bindings/thermal/mediatek,lvts-thermal.h"
v11:
- Rebase on top of "thermal/linux-next" :
base=0d568e144ead70189e7f16066dcb155b78ff9266
- Remove unsupported SoC (mt8192) from dt-binding definition
- Fix coding style issues :
- Move litterals to define
- Add interrupt macros
- Remove wildcard : only mt8195 is supported for now
v10:
- Rebase on top of "thermal/linux-next" : thermal-v6.3-rc1
- Rework the LVTS driver
- Add the thermal trip temperature and cooling devices for the sensors supported by the driver
v9:
- Rebase on top of 6.0.0-rc1
- Fix coding style issues
- Fix commit titles and commit messages
- Update dt-bindings :
- Add "allOf:if:then:"
- Use mt8192 as example (instead of mt8195)
- Fix dt-binding errors
- Fix DTS errors
v8:
- Fix coding style issues
- Rebase on top of next-20220803
- Add multi-instance support :
- Rewrite DT-binding and DTS :
- Add DT-binding and DTS for LVTS_v4 (MT8192 and MT8195)
- One LVTS node for each HW Domain (AP and MCU)
- One SW Instance for each HW Domain
- Add a Kconfig sub-menu entry for LVTS and LVTS_v4 SoCs
- Replace platform_get_resource by platform_get_mem_or_io to get Base Address
- Replace platform_get_resource by platform_get_irq to get Interrupt Number
- Add "lvts_" prefix to functions and structs
v7:
- Fix coding style issues
- Rewrite dt bindings
- was not accurate
- Use mt8195 for example (instead of mt8192)
- Rename mt6873 to mt8192
- Remove clock name
- Rebased on top of to series:
- patchwork.kernel.org/project/linux-mediatek/list/?series=637849
- patchwork.kernel.org/project/linux-pm/list/?series=639386
v6:
- Remove temperature aggregation (it will be added in another series)
- Update the way to read the temperature (read one sensor instead of all)
- Add support of mt8195
v5:
- Use 'git mv' for the relocated file.
v4:
- Rebase to kernel-v5.13-rc1
v3:
- change the expression in the lvts_temp_to_raw to dev_s64.
v2:
- Rebase to kernel-5.11-rc1.
- sort headers
- remove initial value 0 of msr_raw in the lvts_temp_to_raw.
- disconstruct the api of lvts_read_tc_msr_raw.
- add the initial value max_temp = 0 and compare e.q. in the lvts_read_all_tc_temperature.
- add the return with an invalid number in the lvts_init.
Balsam CHIHI (6):
thermal: drivers: mediatek: Relocate driver to mediatek folder
dt-bindings: thermal: mediatek: Add LVTS thermal controllers
arm64: dts: mt8195: Add efuse node to mt8195
thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver
arm64: dts: mediatek: mt8195: Add thermal zones and thermal nodes
arm64: dts: mediatek: mt8195: Add temperature mitigation threshold
.../thermal/mediatek,lvts-thermal.yaml | 142 ++
arch/arm64/boot/dts/mediatek/mt8195.dtsi | 272 ++++
drivers/thermal/Kconfig | 14 +-
drivers/thermal/Makefile | 2 +-
drivers/thermal/mediatek/Kconfig | 37 +
drivers/thermal/mediatek/Makefile | 2 +
.../auxadc_thermal.c} | 2 +-
drivers/thermal/mediatek/lvts_thermal.c | 1224 +++++++++++++++++
.../thermal/mediatek,lvts-thermal.h | 19 +
9 files changed, 1702 insertions(+), 12 deletions(-)
create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml
create mode 100644 drivers/thermal/mediatek/Kconfig
create mode 100644 drivers/thermal/mediatek/Makefile
rename drivers/thermal/{mtk_thermal.c => mediatek/auxadc_thermal.c} (99%)
create mode 100644 drivers/thermal/mediatek/lvts_thermal.c
create mode 100644 include/dt-bindings/thermal/mediatek,lvts-thermal.hbase-commit: a2c81dc59d41e92362ab7d41d0c15471ea50637d
Signature · 1 line
2.34.1
PATCH v13 1/6 thermal: drivers: mediatek: Relocate driver to mediatek folder
From: Balsam CHIHI <[email protected]>
Add MediaTek proprietary folder to upstream more thermal zone and cooler drivers, relocate the original thermal controller driver to it, and rename it as "auxadc_thermal.c" to show its purpose more clearly.
---
drivers/thermal/Kconfig | 14 ++++---------
drivers/thermal/Makefile | 2 +-
drivers/thermal/mediatek/Kconfig | 21 +++++++++++++++++++
drivers/thermal/mediatek/Makefile | 1 +
.../auxadc_thermal.c} | 2 +-
5 files changed, 28 insertions(+), 12 deletions(-)
create mode 100644 drivers/thermal/mediatek/Kconfig
create mode 100644 drivers/thermal/mediatek/Makefile
rename drivers/thermal/{mtk_thermal.c => mediatek/auxadc_thermal.c} (99%)drivers/thermal/Kconfig +4 -10
@@ -412,16 +412,10 @@ config DA9062_THERMAL zone. Compatible with the DA9062 and DA9061 PMICs. -config MTK_THERMAL - tristate "Temperature sensor driver for mediatek SoCs" - depends on ARCH_MEDIATEK || COMPILE_TEST - depends on HAS_IOMEM - depends on NVMEM || NVMEM=n - depends on RESET_CONTROLLER - default y - help - Enable this option if you want to have support for thermal management - controller present in Mediatek SoCs +menu "Mediatek thermal drivers" +depends on ARCH_MEDIATEK || COMPILE_TEST +source "drivers/thermal/mediatek/Kconfig" +endmenu config AMLOGIC_THERMAL tristate "Amlogic Thermal Support"
drivers/thermal/Makefile +1 -1
@@ -55,7 +55,7 @@ obj-y += st/ obj-y += qcom/ obj-y += tegra/ obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o -obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o +obj-y += mediatek/ obj-$(CONFIG_GENERIC_ADC_THERMAL) += thermal-generic-adc.o obj-$(CONFIG_UNIPHIER_THERMAL) += uniphier_thermal.o obj-$(CONFIG_AMLOGIC_THERMAL) += amlogic_thermal.o
drivers/thermal/mediatek/Kconfig new file +21 -0
@@ -0,0 +1,21 @@ +config MTK_THERMAL + tristate "MediaTek thermal drivers" + depends on THERMAL_OF + help + This is the option for MediaTek thermal software solutions. + Please enable corresponding options to get temperature + information from thermal sensors or turn on throttle + mechaisms for thermal mitigation. + +if MTK_THERMAL + +config MTK_SOC_THERMAL + tristate "AUXADC temperature sensor driver for MediaTek SoCs" + depends on HAS_IOMEM + help + Enable this option if you want to get SoC temperature + information for MediaTek platforms. + This driver configures thermal controllers to collect + temperature via AUXADC interface. + +endif
drivers/thermal/mediatek/Makefile new file +1 -0
@@ -0,0 +1 @@ +obj-$(CONFIG_MTK_SOC_THERMAL) += auxadc_thermal.o
drivers/thermal/mediatek/auxadc_thermal.c renamed from drivers/thermal/mtk_thermal.c +1 -1
@@ -23,7 +23,7 @@#include <linux/reset.h> #include <linux/types.h> -#include "thermal_hwmon.h" +#include "../thermal_hwmon.h" /* AUXADC Registers */ #define AUXADC_CON1_SET_V 0x008
Signature · 1 line
2.34.1
kernel test robot
build botRe: [PATCH v13 1/6] thermal: drivers: mediatek: Relocate driver to mediatek folder
Thank you for the patch! Perhaps something to improve:
Hi,
Thank you for the patch! Perhaps something to improve:
[auto build test WARNING on a2c81dc59d41e92362ab7d41d0c15471ea50637d]
url: https://github.com/intel-lab-lkp/linux/commits/bchihi-baylibre-com/thermal-drivers-mediatek-Relocate-driver-to-mediatek-folder/20230207-211351 base: a2c81dc59d41e92362ab7d41d0c15471ea50637d patch link: https://lore.kernel.org/r/20230207130958.608305-2-bchihi%40baylibre.com patch subject: [PATCH v13 1/6] thermal: drivers: mediatek: Relocate driver to mediatek folder config: sparc-allyesconfig (https://download.01.org/0day-ci/archive/20230208/[email protected]/config) compiler: sparc64-linux-gcc (GCC) 12.1.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/intel-lab-lkp/linux/commit/0eb89997925c0d7b47bbeee93016146fc660b259
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review bchihi-baylibre-com/thermal-drivers-mediatek-Relocate-driver-to-mediatek-folder/20230207-211351 git checkout 0eb89997925c0d7b47bbeee93016146fc660b259
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=sparc olddefconfig COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=sparc SHELL=/bin/bash drivers/thermal/mediatek/
If you fix the issue, kindly add following tag where applicable | Reported-by: kernel test robot <[email protected]>
All warnings (new ones prefixed by >>):
>> drivers/thermal/mediatek/auxadc_thermal.c:562: warning: expecting prototype for raw_to_mcelsius(). Prototype was for raw_to_mcelsius_v1() instead
vim +562 drivers/thermal/mediatek/auxadc_thermal.c
a4ffe6b52d27f4 drivers/thermal/mtk_thermal.c Michael Kao 2019-02-01 551
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 552 /**
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 553 * raw_to_mcelsius - convert a raw ADC value to mcelsius
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 554 * @mt: The thermal controller
3772bb422072d4 drivers/thermal/mtk_thermal.c Amit Kucheria 2019-11-20 555 * @sensno: sensor number
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 556 * @raw: raw ADC value
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 557 *
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 558 * This converts the raw ADC value to mcelsius using the SoC specific
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 559 * calibration constants
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 560 */
54bf1e5a629dfb drivers/thermal/mtk_thermal.c Henry Yen 2020-04-30 561 static int raw_to_mcelsius_v1(struct mtk_thermal *mt, int sensno, s32 raw)
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 @562 {
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 563 s32 tmp;
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 564
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 565 raw &= 0xfff;
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 566
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 567 tmp = 203450520 << 3;
f84514766985d3 drivers/thermal/mtk_thermal.c Michael Kao 2019-02-01 568 tmp /= mt->conf->cali_val + mt->o_slope;
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 569 tmp /= 10000 + mt->adc_ge;
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 570 tmp *= raw - mt->vts[sensno] - 3350;
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 571 tmp >>= 3;
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 572
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 573 return mt->degc_cali * 500 - tmp;
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 574 }
a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 575 Signature · 2 lines
0-DAY CI Kernel Test Service https://github.com/intel/lkp-tests
Re: [PATCH v13 1/6] thermal: drivers: mediatek: Relocate driver to mediatek folder
this warning has been fixed by this patch :
https://lore.kernel.org/all/[email protected]/
Quoted 64 lines · kernel test robot
Hi,
Thank you for the patch! Perhaps something to improve:
[auto build test WARNING on
a2c81dc59d41e92362ab7d41d0c15471ea50637d]url: https://github.com/intel-lab-lkp/linux/commits/bchihi-baylibre-com/thermal-drivers-mediatek-Relocate-driver-to-mediatek-folder/20230207-211351 base: a2c81dc59d41e92362ab7d41d0c15471ea50637d patch link: https://lore.kernel.org/r/20230207130958.608305-2-bchihi%40baylibre.com patch subject: [PATCH v13 1/6] thermal: drivers: mediatek: Relocate driver to mediatek folder config: sparc-allyesconfig (https://download.01.org/0day-ci/archive/20230208/[email protected]/config) compiler: sparc64-linux-gcc (GCC) 12.1.0reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/intel-lab-lkp/linux/commit/0eb89997925c0d7b47bbeee93016146fc660b259
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review bchihi-baylibre-com/thermal-drivers-mediatek-Relocate-driver-to-mediatek-folder/20230207-211351 git checkout0eb89997925c0d7b47bbeee93016146fc660b259
# save the config file
mkdirbuild_dir&& cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=sparc olddefconfig COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=sparc SHELL=/bin/bashdrivers/thermal/mediatek/If you fix the issue, kindly add following tag where applicable | Reported-by: kernel test robot <[email protected]>
All warnings (new ones prefixed by >>):
Quoted 1 line
Quoted 1 line
drivers/thermal/mediatek/auxadc_thermal.c:562: warning: expecting prototype forraw_to_mcelsius(). Prototype was forraw_to_mcelsius_v1()insteadvim +562
drivers/thermal/mediatek/auxadc_thermal.ca4ffe6b52d27f4 drivers/thermal/mtk_thermal.c Michael Kao 2019-02-01 551 a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 552 /** a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 553 * raw_to_mcelsius - convert a raw ADC value to mcelsius a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 554 * @mt: The thermal controller 3772bb422072d4 drivers/thermal/mtk_thermal.c Amit Kucheria 2019-11-20 555 * @sensno: sensor number a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 556 * @raw: raw ADC value a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 557 * a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 558 * This converts the raw ADC value to mcelsius using the SoC specific a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 559 * calibration constants a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 560 */ 54bf1e5a629dfb drivers/thermal/mtk_thermal.c Henry Yen 2020-04-30 561 static int raw_to_mcelsius_v1(struct mtk_thermal *mt, int sensno, s32 raw) a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 @562 { a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 563 s32 tmp; a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 564 a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 565 raw &= 0xfff; a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 566 a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 567 tmp = 203450520 << 3; f84514766985d3 drivers/thermal/mtk_thermal.c Michael Kao 2019-02-01 568 tmp /= mt->conf->cali_val + mt->o_slope; a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 569 tmp /= 10000 + mt->adc_ge; a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 570 tmp *= raw - mt->vts[sensno] - 3350; a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 571 tmp >>= 3; a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 572 a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 573 return mt->degc_cali * 500 - tmp; a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 574 } a92db1c8089e82 drivers/thermal/mtk_thermal.c Sascha Hauer 2015-11-30 575--
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests
PATCH v13 2/6 dt-bindings: thermal: mediatek: Add LVTS thermal controllers
In reply to [email protected]From: Balsam CHIHI <[email protected]>
Add LVTS thermal controllers dt-binding definition for mt8192 and mt8195.
--- .../thermal/mediatek,lvts-thermal.yaml | 142 ++++++++++++++++++ .../thermal/mediatek,lvts-thermal.h | 19 +++ 2 files changed, 161 insertions(+) create mode 100644 Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml create mode 100644 include/dt-bindings/thermal/mediatek,lvts-thermal.h
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +142 -0
@@ -0,0 +1,142 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/thermal/mediatek,lvts-thermal.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek SoC Low Voltage Thermal Sensor (LVTS) + +maintainers: + - Balsam CHIHI <[email protected]> + +description: | + LVTS is a thermal management architecture composed of three subsystems, + a Sensing device - Thermal Sensing Micro Circuit Unit (TSMCU), + a Converter - Low Voltage Thermal Sensor converter (LVTS), and + a Digital controller (LVTS_CTRL). + +properties: + compatible: + enum: + - mediatek,mt8192-lvts-ap + - mediatek,mt8192-lvts-mcu + - mediatek,mt8195-lvts-ap + - mediatek,mt8195-lvts-mcu + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + description: LVTS reset for clearing temporary data on AP/MCU. + + nvmem-cells: + minItems: 1 + items: + - description: Calibration eFuse data 1 for LVTS + - description: Calibration eFuse data 2 for LVTS + + nvmem-cell-names: + minItems: 1 + items: + - const: lvts-calib-data-1 + - const: lvts-calib-data-2 + + "#thermal-sensor-cells": + const: 1 + +allOf: + - $ref: thermal-sensor.yaml# + + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8192-lvts-ap + - mediatek,mt8192-lvts-mcu + then: + properties: + nvmem-cells: + maxItems: 1 + + nvmem-cell-names: + maxItems: 1 + + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8195-lvts-ap + - mediatek,mt8195-lvts-mcu + then: + properties: + nvmem-cells: + maxItems: 2 + + nvmem-cell-names: + maxItems: 2 + +required: + - compatible + - reg + - interrupts + - clocks + - resets + - nvmem-cells + - nvmem-cell-names + - "#thermal-sensor-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/mt8195-clk.h> + #include <dt-bindings/reset/mt8195-resets.h> + #include <dt-bindings/thermal/mediatek,lvts-thermal.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + lvts_mcu: thermal-sensor@11278000 { + compatible = "mediatek,mt8195-lvts-mcu"; + reg = <0 0x11278000 0 0x1000>; + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&infracfg_ao CLK_INFRA_AO_THERM>; + resets = <&infracfg_ao MT8195_INFRA_RST4_THERM_CTRL_MCU_SWRST>; + nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>; + nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2"; + #thermal-sensor-cells = <1>; + }; + }; + + thermal_zones: thermal-zones { + cpu0-thermal { + polling-delay = <1000>; + polling-delay-passive = <250>; + thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>; + + trips { + cpu0_alert: trip-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu0_crit: trip-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + };
include/dt-bindings/thermal/mediatek,lvts-thermal.h new file +19 -0
@@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ +/* +* Copyright (c) 2023 MediaTek Inc. +* Author: Balsam CHIHI <[email protected]> +*/ + +#ifndef __MEDIATEK_LVTS_DT_H +#define __MEDIATEK_LVTS_DT_H + +#define MT8195_MCU_BIG_CPU0 0 +#define MT8195_MCU_BIG_CPU1 1 +#define MT8195_MCU_BIG_CPU2 2 +#define MT8195_MCU_BIG_CPU3 3 +#define MT8195_MCU_LITTLE_CPU0 4 +#define MT8195_MCU_LITTLE_CPU1 5 +#define MT8195_MCU_LITTLE_CPU2 6 +#define MT8195_MCU_LITTLE_CPU3 7 + +#endif /* __MEDIATEK_LVTS_DT_H */
Signature · 1 line
2.34.1
Re: [PATCH v13 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers
Quoted 24 lines · On 07/02/2023 14:09, [email protected] wrote:
From: Balsam CHIHI <[email protected]>
Add LVTS thermal controllers dt-binding definition for mt8192 and mt8195.
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +18
-0+allOf: + - $ref: thermal-sensor.yaml# + + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8192-lvts-ap + - mediatek,mt8192-lvts-mcu + then: + properties: + nvmem-cells: + maxItems: 1 + + nvmem-cell-names: + maxItems: 1 +
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml line 81
Quoted 10 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +10
-0+ - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8195-lvts-ap + - mediatek,mt8195-lvts-mcu + then: + properties: + nvmem-cells:
minItems: 2
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml line 84
Quoted 3 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +3
-0+ maxItems: 2 + + nvmem-cell-names:
minItems: 2
Quoted 6 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +6
-0+ maxItems: 2 + +required: + - compatible + - reg + - interrupts
(...)
Quoted 10 lines
include/dt-bindings/thermal/mediatek,lvts-thermal.h new file +4
-0@@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ +/* +* Copyright (c) 2023 MediaTek Inc. +* Author: Balsam CHIHI <[email protected]>
include/dt-bindings/thermal/mediatek,lvts-thermal.h line 14
Quoted 10 lines
include/dt-bindings/thermal/mediatek,lvts-thermal.h new file +10
-0+*/ + +#ifndef __MEDIATEK_LVTS_DT_H +#define __MEDIATEK_LVTS_DT_H + +#define MT8195_MCU_BIG_CPU0 0 +#define MT8195_MCU_BIG_CPU1 1 +#define MT8195_MCU_BIG_CPU2 2 +#define MT8195_MCU_BIG_CPU3 3 +#define MT8195_MCU_LITTLE_CPU0 4
These changed for some reason. Why? The indentation is now broken (although not visible above quote, but visible in diff and code).
Best regards,
Krzysztof
Re: [PATCH v13 2/6] dt-bindings: thermal: mediatek: Add LVTS thermal controllers
Hi Krzysztof,
Thank you for the review.
Quoted 30 lines · Krzysztof Kozlowski
Quoted 28 lines · On 07/02/2023 14:09, [email protected] wrote:
From: Balsam CHIHI <[email protected]>
Add LVTS thermal controllers dt-binding definition for mt8192 and mt8195.
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +22
-0+allOf: + - $ref: thermal-sensor.yaml# + + - if: + properties: + compatible: + contains: + enum: + - mediatek,mt8192-lvts-ap + - mediatek,mt8192-lvts-mcu + then: + properties: + nvmem-cells: + maxItems: 1 + + nvmem-cell-names: + maxItems: 1 + + - if: + properties: + compatible: + contains:
Quoted 9 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml line 66
Quoted 6 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +6
-0+ enum: + - mediatek,mt8195-lvts-ap + - mediatek,mt8195-lvts-mcu + then: + properties: + nvmem-cells:minItems: 2
OK,
I will do the change.
Quoted 6 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml line 84
Quoted 3 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +3
-0+ maxItems: 2 + + nvmem-cell-names:minItems: 2
OK,
I will do this change too.
Quoted 24 lines
Quoted 6 lines
Documentation/devicetree/bindings/thermal/mediatek,lvts-thermal.yaml new file +6
-0+ maxItems: 2 + +required: + - compatible + - reg + - interrupts(...)
Quoted 15 lines
include/dt-bindings/thermal/mediatek,lvts-thermal.h new file +9
-0@@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ +/* +* Copyright (c) 2023 MediaTek Inc. +* Author: Balsam CHIHI <[email protected]> +*/ + +#ifndef __MEDIATEK_LVTS_DT_H +#define __MEDIATEK_LVTS_DT_H +
Quoted 8 lines
include/dt-bindings/thermal/mediatek,lvts-thermal.h line 14
Quoted 5 lines
include/dt-bindings/thermal/mediatek,lvts-thermal.h new file +5
-0+#define MT8195_MCU_BIG_CPU0 0 +#define MT8195_MCU_BIG_CPU1 1 +#define MT8195_MCU_BIG_CPU2 2 +#define MT8195_MCU_BIG_CPU3 3 +#define MT8195_MCU_LITTLE_CPU0 4These changed for some reason. Why? The indentation is now broken (although not visible above quote, but visible in diff and code).
I thought that I fixed the indentation.
I will restore it.
Quoted 4 lines
Best regards,
Krzysztof
Best regards,
Balsam
PATCH v13 3/6 arm64: dts: mt8195: Add efuse node to mt8195
In reply to [email protected]From: Balsam CHIHI <[email protected]>
Add efuse node.
This will be required by the thermal driver to get the calibration data.
---
no changes.
---
--- arch/arm64/boot/dts/mediatek/mt8195.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm64/boot/dts/mediatek/mt8195.dtsi +6 -0
@@ -1380,6 +1380,12 @@ pciephy_glb_intr: pciephy-glb-intr@193 { dp_calibration: dp-data@1ac { reg = <0x1ac 0x10>; }; + lvts_efuse_data1: lvts1-calib@1bc { + reg = <0x1bc 0x14>; + }; + lvts_efuse_data2: lvts2-calib@1d0 { + reg = <0x1d0 0x38>; + }; }; u3phy2: t-phy@11c40000 {
Signature · 1 line
2.34.1
PATCH v13 4/6 thermal: drivers: mediatek: Add the Low Voltage Thermal Sensor driver
In reply to [email protected]From: Balsam CHIHI <[email protected]>
The Low Voltage Thermal Sensor (LVTS) is a multiple sensors, multi controllers contained in a thermal domain.
A thermal domains can be the MCU or the AP.
Each thermal domains contain up to seven controllers, each thermal controller handle up to four thermal sensors.
The LVTS has two Finite State Machines (FSM), one to handle the functionin temperatures range like hot or cold temperature and another one to handle monitoring trip point. The FSM notifies via interrupts when a trip point is crossed.
The interrupt is managed at the thermal controller level, so when an interrupt occurs, the driver has to find out which sensor triggered such an interrupt.
The sampling of the thermal can be filtered or immediate. For the former, the LVTS measures several points and applies a low pass filter.
On MT8195 Tomato Chromebook:
--- drivers/thermal/mediatek/Kconfig | 16 + drivers/thermal/mediatek/Makefile | 1 + drivers/thermal/mediatek/lvts_thermal.c | 1224 +++++++++++++++++++++++ 3 files changed, 1241 insertions(+) create mode 100644 drivers/thermal/mediatek/lvts_thermal.c
drivers/thermal/mediatek/Kconfig +16 -0
@@ -18,4 +18,20 @@ config MTK_SOC_THERMAL This driver configures thermal controllers to collect temperature via AUXADC interface. +config MTK_LVTS_THERMAL + tristate "LVTS Thermal Driver for MediaTek SoCs" + depends on HAS_IOMEM + help + Enable this option if you want to get SoC temperature + information for supported MediaTek platforms. + This driver configures LVTS (Low Voltage Thermal Sensor) + thermal controllers to collect temperatures via ASIF + (Analog Serial Interface). + +config MTK_LVTS_THERMAL_DEBUGFS + bool "LVTS thermal debugfs" + depends on MTK_LVTS_THERMAL && DEBUG_FS + help + Enable this option to debug the internals of the device driver. + endif
drivers/thermal/mediatek/Makefile +1 -0
@@ -1 +1,2 @@ obj-$(CONFIG_MTK_SOC_THERMAL) += auxadc_thermal.o +obj-$(CONFIG_MTK_LVTS_THERMAL) += lvts_thermal.o
drivers/thermal/mediatek/lvts_thermal.c new file +1224 -0
1,224 lines not on this page · raw message
Signature · 1 line
2.34.1
PATCH v13 5/6 arm64: dts: mediatek: mt8195: Add thermal zones and thermal nodes
In reply to [email protected]From: Balsam CHIHI <[email protected]>
Add thermal zones and thermal nodes for the mt8195.
--- arch/arm64/boot/dts/mediatek/mt8195.dtsi | 129 +++++++++++++++++++++++ 1 file changed, 129 insertions(+)
arch/arm64/boot/dts/mediatek/mt8195.dtsi +129 -0
@@ -14,6 +14,7 @@ #include <dt-bindings/pinctrl/mt8195-pinfunc.h> #include <dt-bindings/power/mt8195-power.h> #include <dt-bindings/reset/mt8195-resets.h> +#include <dt-bindings/thermal/mediatek,lvts-thermal.h> / { compatible = "mediatek,mt8195";
@@ -954,6 +955,17 @@ spi0: spi@1100a000 { status = "disabled"; }; + lvts_ap: thermal-sensor@1100b000 { + compatible = "mediatek,mt8195-lvts-ap"; + reg = <0 0x1100b000 0 0x1000>; + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&infracfg_ao CLK_INFRA_AO_THERM>; + resets = <&infracfg_ao MT8195_INFRA_RST0_THERM_CTRL_SWRST>; + nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>; + nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2"; + #thermal-sensor-cells = <1>; + }; + spi1: spi@11010000 { compatible = "mediatek,mt8195-spi", "mediatek,mt6765-spi";
@@ -1114,6 +1126,17 @@ mmc2: mmc@11250000 { status = "disabled"; }; + lvts_mcu: thermal-sensor@11278000 { + compatible = "mediatek,mt8195-lvts-mcu"; + reg = <0 0x11278000 0 0x1000>; + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&infracfg_ao CLK_INFRA_AO_THERM>; + resets = <&infracfg_ao MT8195_INFRA_RST4_THERM_CTRL_MCU_SWRST>; + nvmem-cells = <&lvts_efuse_data1 &lvts_efuse_data2>; + nvmem-cell-names = "lvts-calib-data-1", "lvts-calib-data-2"; + #thermal-sensor-cells = <1>; + }; + xhci1: usb@11290000 { compatible = "mediatek,mt8195-xhci", "mediatek,mtk-xhci";
@@ -2387,4 +2410,110 @@ dp_tx: dp-tx@1c600000 { status = "disabled"; }; }; + + thermal_zones: thermal-zones { + cpu0-thermal { + polling-delay = <0>; + polling-delay-passive = <0>; + thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>; + trips { + cpu0_crit: trip-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu1-thermal { + polling-delay = <0>; + polling-delay-passive = <0>; + thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU1>; + trips { + cpu1_crit: trip-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu2-thermal { + polling-delay = <0>; + polling-delay-passive = <0>; + thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU2>; + trips { + cpu2_crit: trip-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu3-thermal { + polling-delay = <0>; + polling-delay-passive = <0>; + thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU3>; + trips { + cpu3_crit: trip-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu4-thermal { + polling-delay = <0>; + polling-delay-passive = <0>; + thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU0>; + trips { + cpu4_crit: trip-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu5-thermal { + polling-delay = <0>; + polling-delay-passive = <0>; + thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU1>; + trips { + cpu5_crit: trip-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu6-thermal { + polling-delay = <0>; + polling-delay-passive = <0>; + thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU2>; + trips { + cpu6_crit: trip-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu7-thermal { + polling-delay = <0>; + polling-delay-passive = <0>; + thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU3>; + trips { + cpu7_crit: trip-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; };
Signature · 1 line
2.34.1
PATCH v13 6/6 arm64: dts: mediatek: mt8195: Add temperature mitigation threshold
In reply to [email protected]From: Balsam CHIHI <[email protected]>
The mt8195 SoC has several hotspots around the CPUs. Specify the targeted temperature threshold when to apply the mitigation and define the associated cooling devices.
--- arch/arm64/boot/dts/mediatek/mt8195.dtsi | 169 ++++++++++++++++++++--- 1 file changed, 153 insertions(+), 16 deletions(-)
arch/arm64/boot/dts/mediatek/mt8195.dtsi +153 -16
@@ -14,6 +14,7 @@ #include <dt-bindings/pinctrl/mt8195-pinfunc.h> #include <dt-bindings/power/mt8195-power.h> #include <dt-bindings/reset/mt8195-resets.h> +#include <dt-bindings/thermal/thermal.h> #include <dt-bindings/thermal/mediatek,lvts-thermal.h> / {
@@ -2413,107 +2414,243 @@ dp_tx: dp-tx@1c600000 { thermal_zones: thermal-zones { cpu0-thermal { - polling-delay = <0>; - polling-delay-passive = <0>; + polling-delay = <1000>; + polling-delay-passive = <250>; thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU0>; + trips { + cpu0_alert: trip-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu0_crit: trip-crit { temperature = <100000>; hysteresis = <2000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&cpu0_alert>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; cpu1-thermal { - polling-delay = <0>; - polling-delay-passive = <0>; + polling-delay = <1000>; + polling-delay-passive = <250>; thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU1>; + trips { + cpu1_alert: trip-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu1_crit: trip-crit { temperature = <100000>; hysteresis = <2000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&cpu1_alert>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; cpu2-thermal { - polling-delay = <0>; - polling-delay-passive = <0>; + polling-delay = <1000>; + polling-delay-passive = <250>; thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU2>; + trips { + cpu2_alert: trip-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu2_crit: trip-crit { temperature = <100000>; hysteresis = <2000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&cpu2_alert>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; cpu3-thermal { - polling-delay = <0>; - polling-delay-passive = <0>; + polling-delay = <1000>; + polling-delay-passive = <250>; thermal-sensors = <&lvts_mcu MT8195_MCU_LITTLE_CPU3>; + trips { + cpu3_alert: trip-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu3_crit: trip-crit { temperature = <100000>; hysteresis = <2000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&cpu3_alert>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; cpu4-thermal { - polling-delay = <0>; - polling-delay-passive = <0>; + polling-delay = <1000>; + polling-delay-passive = <250>; thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU0>; + trips { + cpu4_alert: trip-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu4_crit: trip-crit { temperature = <100000>; hysteresis = <2000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&cpu4_alert>; + cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; cpu5-thermal { - polling-delay = <0>; - polling-delay-passive = <0>; + polling-delay = <1000>; + polling-delay-passive = <250>; thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU1>; + trips { + cpu5_alert: trip-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu5_crit: trip-crit { temperature = <100000>; hysteresis = <2000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&cpu5_alert>; + cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; cpu6-thermal { - polling-delay = <0>; - polling-delay-passive = <0>; + polling-delay = <1000>; + polling-delay-passive = <250>; thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU2>; + trips { + cpu6_alert: trip-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu6_crit: trip-crit { temperature = <100000>; hysteresis = <2000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&cpu6_alert>; + cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; cpu7-thermal { - polling-delay = <0>; - polling-delay-passive = <0>; + polling-delay = <1000>; + polling-delay-passive = <250>; thermal-sensors = <&lvts_mcu MT8195_MCU_BIG_CPU3>; + trips { + cpu7_alert: trip-alert { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu7_crit: trip-crit { temperature = <100000>; hysteresis = <2000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&cpu7_alert>; + cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; }; };
Signature · 1 line
2.34.1