dt-bindings: rockchip: Sync rockchip, vop2.h from Linux
Subsystems (4)
PATCH v3 1/7 dt-bindings: rockchip: Sync rockchip, vop2.h from Linux
Sync rockchip,vop2.h from linux-next, and the last commit is
commit <604be85547ce> ("drm/rockchip: Add VOP2 driver")
---
Changes for v3:
- none
Changes for v2:
- collect Kever RB
include/dt-bindings/soc/rockchip,vop2.h | 14 ++++++++++++++ 1 file changed, 14 insertions(+) create mode 100644 include/dt-bindings/soc/rockchip,vop2.h
include/dt-bindings/soc/rockchip,vop2.h new file +14 -0
@@ -0,0 +1,14 @@ +/* SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause */ + +#ifndef __DT_BINDINGS_ROCKCHIP_VOP2_H +#define __DT_BINDINGS_ROCKCHIP_VOP2_H + +#define ROCKCHIP_VOP2_EP_RGB0 1 +#define ROCKCHIP_VOP2_EP_HDMI0 2 +#define ROCKCHIP_VOP2_EP_EDP0 3 +#define ROCKCHIP_VOP2_EP_MIPI0 4 +#define ROCKCHIP_VOP2_EP_LVDS0 5 +#define ROCKCHIP_VOP2_EP_MIPI1 6 +#define ROCKCHIP_VOP2_EP_LVDS1 7 + +#endif /* __DT_BINDINGS_ROCKCHIP_VOP2_H */
Signature · 1 line
2.25.1
PATCH v3 2/7 arm64: dts: rockchip: rk3566: Add Radxa Compute Module 3
Radxa Compute Module 3(CM3) is one of the modules from a series System On Module based on the Radxa ROCK 3 series and is compatible with Raspberry Pi CM4 pinout and form factor.
Specification:
- Rockchip RK3566
- up to 8GB LPDDR4
- up to 128GB high performance eMMC
- Optional wireless LAN, 2.4GHz and 5.0GHz IEEE 802.11b/g/n/ac wireless, BT 5.0, BLE with onboard and external antenna.
- Gigabit Ethernet PHY
Radxa CM3 needs to mount on top of this IO board in order to create complete Radxa CM3 IO board platform.
Since Radxa CM3 is compatible with Raspberry Pi CM4 pinout so it is possible to mount Radxa CM3 on top of the Rasberry Pi CM4 IO board.
linux-next commit for the same,
commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa CM3")
Add support for Radxa CM3.
---
Changes for v3:
- updated linux-next commit
Changes for v2:
- collect Kever RB
- add linux-next commit
arch/arm/dts/rk3566-radxa-cm3.dtsi | 425 +++++++++++++++++++++++++++++ 1 file changed, 425 insertions(+) create mode 100644 arch/arm/dts/rk3566-radxa-cm3.dtsi
arch/arm/dts/rk3566-radxa-cm3.dtsi new file +425 -0
@@ -0,0 +1,425 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2022 Radxa Limited + * Copyright (c) 2022 Amarula Solutions(India) + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> + +/ { + compatible = "radxa,cm3", "rockchip,rk3566"; + + aliases { + mmc0 = &sdhci; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_STATUS; + linux,default-trigger = "timer"; + default-state = "on"; + pinctrl-names = "default"; + pinctrl-0 = <&user_led2>; + }; + }; + + vcc_sys: vcc-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + vcc_1v8: vcc-1v8-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_1v8_p>; + }; + + vcc_3v3: vcc-3v3-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc3v3_sys>; + }; + + vcca_1v8: vcca-1v8-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcca_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_1v8_p>; + }; + + sdio_pwrseq: pwrseq-sdio { + compatible = "mmc-pwrseq-simple"; + clocks = <&rk817 1>; + clock-names = "ext_clock"; + pinctrl-names = "default"; + pinctrl-0 = <&wifi_reg_on_h>; + reset-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_LOW>; + }; +}; + +&cpu0 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu1 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu2 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu3 { + cpu-supply = <&vdd_cpu>; +}; + +&gpu { + mali-supply = <&vdd_gpu_npu>; + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + vdd_cpu: regulator@1c { + compatible = "tcs,tcs4525"; + reg = <0x1c>; + fcs,suspend-voltage-selector = <1>; + regulator-name = "vdd_cpu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <712500>; + regulator-max-microvolt = <1390000>; + regulator-ramp-delay = <2300>; + vin-supply = <&vcc_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + rk817: pmic@20 { + compatible = "rockchip,rk817"; + reg = <0x20>; + #clock-cells = <1>; + clock-output-names = "rk817-clkout1", "rk817-clkout2"; + interrupt-parent = <&gpio0>; + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l>; + rockchip,system-power-controller; + wakeup-source; + + vcc1-supply = <&vcc_sys>; + vcc2-supply = <&vcc_sys>; + vcc3-supply = <&vcc_sys>; + vcc4-supply = <&vcc_sys>; + vcc5-supply = <&vcc_sys>; + vcc6-supply = <&vcc_sys>; + vcc7-supply = <&vcc_sys>; + + regulators { + vdd_logic: DCDC_REG1 { + regulator-name = "vdd_logic"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <6001>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vdd_gpu_npu: DCDC_REG2 { + regulator-name = "vdd_gpu_npu"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <6001>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-name = "vcc_ddr"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc3v3_sys: DCDC_REG4 { + regulator-name = "vcc3v3_sys"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcca1v8_pmu: LDO_REG1 { + regulator-name = "vcca1v8_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vdda_0v9: LDO_REG2 { + regulator-name = "vdda_0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v9_pmu: LDO_REG3 { + regulator-name = "vdda0v9_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vccio_acodec: LDO_REG4 { + regulator-name = "vccio_acodec"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd: LDO_REG5 { + regulator-name = "vccio_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_pmu: LDO_REG6 { + regulator-name = "vcc3v3_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_1v8_p: LDO_REG7 { + regulator-name = "vcc_1v8_p"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc1v8_dvp: LDO_REG8 { + regulator-name = "vcc1v8_dvp"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc2v8_dvp: LDO_REG9 { + regulator-name = "vcc2v8_dvp"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + }; + }; +}; + +&pinctrl { + bluetooth { + bt_host_wake_h: bt-host-wake-h { + rockchip,pins = <2 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + bt_reg_on_h: bt-reg-on-h { + rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + bt_wake_host_h: bt-wake-host-h { + rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pmic { + pmic_int_l: pmic-int-l { + rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + leds { + user_led2: user-led2 { + rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + wifi { + wifi_reg_on_h: wifi-reg-on-h { + rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + wifi_host_wake_h: wifi-host-wake-h { + rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&pmu_io_domains { + pmuio1-supply = <&vcc3v3_pmu>; + pmuio2-supply = <&vcc_3v3>; + vccio1-supply = <&vccio_acodec>; + vccio2-supply = <&vcc_1v8>; + vccio3-supply = <&vccio_sd>; + vccio4-supply = <&vcc_1v8>; + vccio5-supply = <&vcc_3v3>; + vccio6-supply = <&vcc_3v3>; + vccio7-supply = <&vcc_3v3>; + status = "okay"; +}; + +&saradc { + vref-supply = <&vcca_1v8>; + status = "okay"; +}; + +&sdmmc1 { + #address-cells = <1>; + #size-cells = <0>; + bus-width = <4>; + disable-wp; + cap-sd-highspeed; + cap-sdio-irq; + keep-power-in-suspend; + mmc-pwrseq = <&sdio_pwrseq>; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_clk &sdmmc1_cmd>; + sd-uhs-sdr104; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vcc_1v8>; + status = "okay"; + + wifi@1 { + compatible = "brcm,bcm43455-fmac"; + reg = <1>; + interrupt-parent = <&gpio2>; + interrupts = <RK_PC1 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host-wake"; + pinctrl-names = "default"; + pinctrl-0 = <&wifi_host_wake_h>; + }; +}; + +&sdhci { + bus-width = <8>; + max-frequency = <200000000>; + mmc-hs200-1_8v; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vcc_1v8>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1m0_ctsn &uart1m0_rtsn &uart1m0_xfer>; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm4345c5"; + clocks = <&rk817 1>; + clock-names = "lpo"; + device-wakeup-gpios = <&gpio2 RK_PB2 GPIO_ACTIVE_HIGH>; + host-wakeup-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&bt_host_wake_h &bt_reg_on_h &bt_wake_host_h>; + vbat-supply = <&vcc_3v3>; + vddio-supply = <&vcc_1v8>; + }; +}; + +&usb2phy0 { + status = "okay"; +}; + +&usb2phy1 { + status = "okay"; +}; + +&tsadc { + rockchip,hw-tshut-mode = <1>; + rockchip,hw-tshut-polarity = <0>; + status = "okay"; +};
Signature · 1 line
2.25.1
PATCH v3 3/7 arm64: dts: rockchip: rk3566: Add Radxa Compute Module 3 IO
In reply to Jagan TekiRadxa Compute Module 3(CM3) IO board an application board from Radxa and is compatible with Raspberry Pi CM4 IO form factor.
Specification:
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- Phone jack
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create complete Radxa CM3 IO board platform.
linux-next commit for the same,
commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa CM3")
Add support for Radxa CM3 IO Board.
---
Changes for v3:
- updated linux-next commit
Changes for v2:
- collect Kever RB
- add linux-next commit
arch/arm/dts/Makefile | 1 + arch/arm/dts/rk3566-radxa-cm3-io.dts | 272 +++++++++++++++++++++++++++ 2 files changed, 273 insertions(+) create mode 100644 arch/arm/dts/rk3566-radxa-cm3-io.dts
arch/arm/dts/Makefile +1 -0
@@ -165,6 +165,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \ rk3399pro-rock-pi-n10.dtb dtb-$(CONFIG_ROCKCHIP_RK3568) += \ + rk3566-radxa-cm3-io.dtb \ rk3568-evb.dtb dtb-$(CONFIG_ROCKCHIP_RV1108) += \
arch/arm/dts/rk3566-radxa-cm3-io.dts new file +272 -0
272 lines not on this page · raw message
Signature · 1 line
2.25.1
PATCH v3 4/7 board: rockchip: Add Radxa Compute Module 3 IO Board
In reply to Jagan TekiRadxa Compute Module 3(CM3) IO board an application board from Radxa and is compatible with Raspberry Pi CM4 IO form factor.
Radxa CM3 needs to mount on top of this IO board in order to create complete Radxa CM3 IO board platform.
Add support for Radxa CM3 IO Board defconfig and -u-boot.dtsi
---
Changes for v3:
- none
Changes for v2:
- collect Kever RB
arch/arm/dts/rk3566-radxa-cm3-io-u-boot.dtsi | 18 ++++++ board/rockchip/evb_rk3568/MAINTAINERS | 5 ++ configs/radxa-cm3-io-rk3566_defconfig | 68 ++++++++++++++++++++ 3 files changed, 91 insertions(+) create mode 100644 arch/arm/dts/rk3566-radxa-cm3-io-u-boot.dtsi create mode 100644 configs/radxa-cm3-io-rk3566_defconfig
arch/arm/dts/rk3566-radxa-cm3-io-u-boot.dtsi new file +18 -0
@@ -0,0 +1,18 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2021 Rockchip Electronics Co., Ltd + */ + +#include "rk356x-u-boot.dtsi" + +/ { + chosen { + stdout-path = &uart2; + }; +}; + +&uart2 { + clock-frequency = <24000000>; + u-boot,dm-spl; + status = "okay"; +};
board/rockchip/evb_rk3568/MAINTAINERS +5 -0
@@ -4,3 +4,8 @@ S: Maintained F: board/rockchip/evb_rk3568 F: include/configs/evb_rk3568.h F: configs/evb-rk3568_defconfig + +RADXA-CM3 +M: Jagan Teki <[email protected]> +S: Maintained +F: configs/radxa-cm3-io-rk3566_defconfig
configs/radxa-cm3-io-rk3566_defconfig new file +68 -0
68 lines not on this page · raw message
Signature · 1 line
2.25.1
PATCH v3 5/7 phy: rockchip: inno-usb2: Add support #address_cells = 2
In reply to Jagan TekiNew Rockchip devices have the usb phy nodes as standalone devices. These nodes have register nodes with #address_cells = 2, but only use 32 bit addresses.
Adjust the driver to check if the returned address is "0", and adjust the index in that case.
Derived and adjusted the similar change from linux-next with below
commit <9c19c531dc98> ("phy: phy-rockchip-inno-usb2: support #address_cells = 2")
---
Changes for v3:
- new patch
drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)
drivers/phy/rockchip/phy-rockchip-inno-usb2.c +10 -1
@@ -179,12 +179,21 @@ static int rockchip_usb2phy_probe(struct udevice *dev)if (IS_ERR (priv->reg_base))return PTR_ERR (priv->reg_base); - ret =ofnode_read_u32 (dev_ofnode (dev),"reg" , ®); + ret =ofnode_read_u32_index (dev_ofnode (dev),"reg" ,0 , ®);if (ret) {dev_err (dev,"failed to read reg property (ret = %d)\n" , ret);return ret; } +/* support address_cells=2 */ +if (reg ==0 ) { +if (ofnode_read_u32_index (dev_ofnode (dev),"reg" ,1 , ®)) { +dev_err (dev,"%s must have reg[1]\n" , +ofnode_get_name (dev_ofnode (dev))); +return -EINVAL ; + } + } + phy_cfgs = (const struct rockchip_usb2phy_cfg *)dev_get_driver_data (dev);if (!phy_cfgs)
Signature · 1 line
2.25.1
PATCH v3 6/7 phy: rockchip-inno-usb2: Add USB2 PHY for rk3568
In reply to Jagan TekiFrom: Manoj Sai <[email protected]>
RK3568 has two USB 2.0 PHYs, and each PHY has two ports, the OTG port of PHY0 support OTG mode with charging detection function, they are similar to previous Rockchip SoCs.
However, there are three different designs for RK3568 USB 2.0 PHY.
1. RK3568 uses independent USB GRF module for each USB 2.0 PHY.
2. RK3568 accesses the registers of USB 2.0 PHY IP directly by APB.
3. The two ports of USB 2.0 PHY share one interrupt.
This patch only PHY1 with necessary attributes required to function USBPHY1 on U-Boot.
---
Changes for v3:
- new patch
drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 29 +++++++++++++++++++ 1 file changed, 29 insertions(+)
drivers/phy/rockchip/phy-rockchip-inno-usb2.c +29 -0
@@ -298,11 +298,40 @@ static const struct rockchip_usb2phy_cfg rk3399_usb2phy_cfgs[] = { {/* sentinel */ } }; +static const struct rockchip_usb2phy_cfg rk3568_phy_cfgs[] = { + { + .reg =0xfe8b0000 , + .port_cfgs = { + [USB2PHY_PORT_OTG ] = { + .phy_sus = {0x0000 ,8 ,0 ,0x1d2 ,0x1d1 }, + .ls_det_en = {0x0080 ,0 ,0 ,0 ,1 }, + .ls_det_st = {0x0084 ,0 ,0 ,0 ,1 }, + .ls_det_clr = {0x0088 ,0 ,0 ,0 ,1 }, + .utmi_ls = {0x00c0 ,5 ,4 ,0 ,1 }, + .utmi_hstdet = {0x00c0 ,7 ,7 ,0 ,1 } + }, + [USB2PHY_PORT_HOST ] = { + .phy_sus = {0x0004 ,8 ,0 ,0x1d2 ,0x1d1 }, + .ls_det_en = {0x0080 ,1 ,1 ,0 ,1 }, + .ls_det_st = {0x0084 ,1 ,1 ,0 ,1 }, + .ls_det_clr = {0x0088 ,1 ,1 ,0 ,1 }, + .utmi_ls = {0x00c0 ,17 ,16 ,0 ,1 }, + .utmi_hstdet = {0x00c0 ,19 ,19 ,0 ,1 } + } + }, + }, + {/* sentinel */ } +}; +static const struct udevice_id rockchip_usb2phy_ids[] = { { .compatible ="rockchip,rk3399-usb2phy" , .data = (ulong)&rk3399_usb2phy_cfgs, }, + { + .compatible ="rockchip,rk3568-usb2phy" , + .data = (ulong)&rk3568_phy_cfgs, + }, {/* sentinel */ } };
Signature · 1 line
2.25.1
PATCH v3 7/7 config: Enable USB 2.0 for Radxa CM3-IO
In reply to Jagan Teki=> usb start
starting USB...
Bus usb@fd800000: USB EHCI 1.00
scanning bus usb@fd800000 for devices... 4 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)
| USB 2.0 Hub
|
+-3 Mass Storage (480 Mb/s, 224mA)
| SanDisk Dual Drive 04019c9b2e1a58f24ee318c3c123aa5
|
+-4 Human Interface (12 Mb/s, 100mA)CX 2.4G Receiver
---
Changes for v3:
- new patch
configs/radxa-cm3-io-rk3566_defconfig | 5 +++++ 1 file changed, 5 insertions(+)
configs/radxa-cm3-io-rk3566_defconfig +5 -0
@@ -39,6 +39,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_ATF=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set # CONFIG_SPL_DOS_PARTITION is not set CONFIG_SPL_OF_CONTROL=y
@@ -58,11 +59,15 @@ CONFIG_MMC_SDHCI_SDMA=y CONFIG_MMC_SDHCI_ROCKCHIP=y CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y CONFIG_REGULATOR_PWM=y CONFIG_PWM_ROCKCHIP=y CONFIG_SPL_RAM=y CONFIG_BAUDRATE=1500000 CONFIG_DEBUG_UART_SHIFT=2 CONFIG_SYSRESET=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y # CONFIG_BINMAN_FDT is not set CONFIG_ERRNO_STR=y
Signature · 1 line
2.25.1
Hi Kever,
Quoted 5 lines · Jagan Teki
Sync rockchip,vop2.h from linux-next, and the last commit is
commit <
604be85547ce> ("drm/rockchip: Add VOP2 driver")
Quoted 7 lines
Reviewed-by Kever Yang <[email protected]>Signed-off-by Jagan Teki <[email protected]>---
Changes for v3:
- none
Changes for v2:
- collect Kever RB
Any comments on this series?
Jagan.