Skip to contentSkip to conversation

GMU-less A6xx support (A610, A619_holi)

PATCH Superseded Konrad Dybcio 1 participant 19 messages May 20, 2023

Subsystems (6)

v7 of 9 Superseded Latest is v9 →

lore
Share & tools
lore
#0 lore raw

v7 cover GMU-less A6xx support (A610, A619_holi)

v6 -> v7:
- Rebase on next-20230519 (A640/650 speedbin merged already)

- separate out the .get_timestamp cb for gmu wrapper

- check for gmu presence inside a6xx_llc_slices_(init|destroy) instead of before calling them

- use REG_A6XX_RBBM_GPR0_CNTL instead of literal 0x18

- move a6xx_bus_clear_pending_transactions to a6xx_gpu, clean it up and reuse it for gmu wrapper gpus

- drop clearing RBBM_GBIF (GBIF from GX's POV) as part of draining the buses, it's not necessary

- introduce a helper for gpu softreset

- sw-reset the gmu wrapper GPUS *after* draining GBIF and only reset it if it's hung

- reword the commit message in "Remove both GBIF and RBBM GBIF halt on hw init" and move it before gmu wrapper-specific changes

- drop set_rate logic from a6xx_pm_suspend as the clock simply gets disabled and we don't have to worry about scaling problems as OPP and devfreq take care of that, validated with debugcc

- drop a level of indentation in _a6xx_check_idle() to hopefully improve readability

- check for !a610 instead of gmu_wrapper||a619_holi in sptprac cc toggling in a6xx_set_hwcg()

- pick up krzk's rb on bindings

All external dependencies have been merged since the last revision.

v6: https://lore.kernel.org/r/[email protected]

v5 -> v6:
- Rebase on 8ead96783163 ("drm/msm/gpu: Move BO allocation out of hw_init") (Add .ucode_load to funcs_gmuwrapper)
- Drop A6[45]0 speedbin deps, merged into msm-next

Dependencies:
- https://lore.kernel.org/linux-arm-msm/[email protected]/ (to work properly)

v5: https://lore.kernel.org/linux-arm-msm/[email protected]/

v4 -> v5:
- Add a newline before the new allOf:if: [3/15]
- Enforce 6 clocks on A619_holi/A610 [2/15]
- Pick up tags
- Improve error handling in a6xx_pm_resume [6/15]
- Add patch [1/15] (fix an existing issue) which can be picked separately and account for it in [6/15]
- Rebase atop Akhil's CX shutdown patches and incorporate analogous logic
- Fix a regression introduced in v3 that made the fw loader expect GMU fw on GMU wrapper GPUs

Dependencies:
- https://lore.kernel.org/linux-arm-msm/[email protected]/ (to apply)
- https://lore.kernel.org/linux-arm-msm/[email protected]/ (to work properly)

v4: https://lore.kernel.org/r/[email protected]

v3 -> v4:
- Drop the mistakengly-included and wrong A3xx-A5xx bindings changes
- Improve bindings commit messages to better explain what GMU Wrapper is
- Drop the A680 highest bank bit value adjustment patch
- Sort UBWC config variables in a reverse-Christmass-tree fashion [4/14]
- Don't alter any UBWC config values in [4/14]
- Do so for a619_holi in [8/14]
- Rebase on next-20230314 (shouldn't matter at all)

v3: https://lore.kernel.org/r/[email protected]

v2 -> v3:
New dependencies:
- https://lore.kernel.org/linux-arm-msm/[email protected]/T/#t
- https://lore.kernel.org/linux-arm-msm/[email protected]/

Sidenote: A speedbin rework is in progress, the of_machine_is_compatible calls in A619_holi are ugly (but well, necessary..) but they'll be replaced with socid matching in this or the next kernel cycle.

Due to the new way of identifying GMU wrapper GPUs, configuring 6350 to use wrapper would cause the wrong fuse values to be checked, but that will be solved by the conversion + the ultimate goal is to use the GMU whenever possible with the wrapper left for GMU-less Adrenos and early bringup debugging of GMU-equipped ones.

- Ship dt-bindings in this series as we're referencing the compatible now

- "De-staticize" -> "remove static keyword" [3/15]

- Track down all the values in [4/15]

- Add many comments and explanations in [4/15]

- Fix possible return-before-mutex-unlock [5/15]

- Explain the GMU wrapper a bit more in the commit msg [5/15]

- Separate out pm_resume/suspend for GMU-wrapper GPUs to make things cleaner [5/15]

- Don't check if info exists, it has to at this point [5/15]

- Assign gpu->info early and clean up following if statements in a6xx_gpu_init [5/15]

- Determine whether we use GMU wrapper based on the GMU compatible instead of a quirk [5/15]

- Use a struct field to annotate whether we're using gmu wrapper so that it can be assigned at runtime (turns out a619 holi-ness cannot be determined by patchid + that will make it easier to test out GMU GPUs without actually turning on the GMU if anybody wants to do so) [5/15]

- Unconditionally hook up gx to the gmu wrapper (otherwise our gpu will not get power) [5/15]

- Don't check for gx domain presence in gmu_wrapper paths, it's guaranteed [5/15]

- Use opp set rate in the gmuwrapper suspend path [5/15]

- Call opp functions on the GPU device and not on the DRM device of mdp4/5/DPU1 half the time (WHOOOOPS!) [5/15]

- Disable the memory clock in a6xx_pm_suspend instead of enabling it (moderate oops) [5/15]

- Call the forgotten clk_bulk_disable_unprepare in a6xx_pm_suspend [5/15]

- Set rate to FMIN (a6xx really doesn't like rate=0 + that's what msm-5.x does anyway) before disabling core clock [5/15]

- pm_runtime_get_sync -> pm_runtime_resume_and_get [5/15]

- Don't annotate no cached BO support with a quirk, as A619_holi is merged into the A619 entry in the big const struct - this means that all GPUs operating in gmu wrapper configuration will be implicitly treated as if they didn't have this feature [7/15]

- Drop OPP rate & icc related patches, they're a part of a separate series now; rebase on it

- Clean up extra parentheses [8/15]

- Identify A619_holi by checking the compatible of its GMU instead of patchlevel [8/15]

- Drop "Fix up A6XX protected registers" - unnecessary, Rob will add a comment explaining why

- Fix existing UBWC values for A680, new patch [10/15]

- Use adreno_is_aXYZ macros in speedbin matching [13/15] - new patch

v2: https://lore.kernel.org/linux-arm-msm/[email protected]/

v1 -> v2:
- Fix A630 values in [2/14]
- Fix [6/14] for GMU-equipped GPUs

Link to v1: https://lore.kernel.org/linux-arm-msm/[email protected]/

This series concludes my couple-weeks-long suffering of figuring out the ins and outs of the "non-standard" A6xx GPUs which feature no GMU.

The GMU functionality is essentially emulated by parting out a "GMU wrapper" region, which is essentially just a register space within the GPU. It's modeled to be as similar to the actual GMU as possible while staying as unnecessary as we can make it - there's no IRQs, communicating with a microcontroller, no RPMh communication etc. etc. I tried to reuse as much code as possible without making a mess where every even line is used for GMU and every odd line is used for GMU wrapper..

This series contains:
- plumbing for non-GMU operation, if-ing out GMU calls based on GMU presence
- GMU wrapper support
- A610 support (w/ speedbin)
- A619 support (w/ speedbin)
- couple of minor fixes and improvements
- VDDCX/VDDGX scaling fix for non-GMU GPUs (concerns more than just A6xx)
- Enablement of opp interconnect properties

A619_holi works perfectly fine using the already-present A619 support in mesa. A610 needs more work on that front, but can already replay command traces captures on downstream.

NOTE: the "drm/msm/a6xx: Add support for A619_holi" patch contains two occurences of 0x18 used in place of a register #define, as it's supposed to be RBBM_GPR0_CNTL, but that will only be present after mesa-side changes are merged and headers are synced from there.

Speedbin patches depend on:
https://lore.kernel.org/linux-arm-msm/[email protected]/

---
Konrad Dybcio (18):
dt-bindings: display/msm: gpu: Document GMU wrapper-equipped A6xx
dt-bindings: display/msm/gmu: Add GMU wrapper
drm/msm/a6xx: Remove static keyword from sptprac en/disable functions drm/msm/a6xx: Move force keepalive vote removal to a6xx_gmu_force_off() drm/msm/a6xx: Move a6xx_bus_clear_pending_transactions to a6xx_gpu drm/msm/a6xx: Improve a6xx_bus_clear_pending_transactions() drm/msm/a6xx: Add a helper for software-resetting the GPU drm/msm/a6xx: Remove both GBIF and RBBM GBIF halt on hw init drm/msm/a6xx: Extend and explain UBWC config
drm/msm/a6xx: Introduce GMU wrapper support
drm/msm/adreno: Disable has_cached_coherent in GMU wrapper configurations drm/msm/a6xx: Add support for A619_holi
drm/msm/a6xx: Add A610 support
drm/msm/a6xx: Fix some A619 tunables
drm/msm/a6xx: Use "else if" in GPU speedbin rev matching drm/msm/a6xx: Use adreno_is_aXYZ macros in speedbin matching drm/msm/a6xx: Add A619_holi speedbin support
drm/msm/a6xx: Add A610 speedbin support

 .../devicetree/bindings/display/msm/gmu.yaml       |  50 +-
 .../devicetree/bindings/display/msm/gpu.yaml       |  61 ++-
 drivers/gpu/drm/msm/adreno/a6xx_gmu.c              | 122 +++--
 drivers/gpu/drm/msm/adreno/a6xx_gmu.h              |   2 +
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c              | 516 ++++++++++++++++++---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.h              |   4 +
 drivers/gpu/drm/msm/adreno/a6xx_gpu_state.c        |  14 +-
 drivers/gpu/drm/msm/adreno/adreno_device.c         |  17 +-
 drivers/gpu/drm/msm/adreno/adreno_gpu.c            |   8 +-
 drivers/gpu/drm/msm/adreno/adreno_gpu.h            |  33 +-
 10 files changed, 690 insertions(+), 137 deletions(-)

---
base-commit: dbd91ef4e91c1ce3a24429f5fb3876b7a0306733
change-id: 20230223-topic-gmuwrapper-b4fff5fd7789

Best regards,

Signature · 1 line
Konrad Dybcio <[email protected]>
#1 lore raw

PATCH v7 1/18 dt-bindings: display/msm: gpu: Document GMU wrapper-equipped A6xx

The "GMU Wrapper" is Qualcomm's name for "let's treat the GPU blocks we'd normally assign to the GMU as if they were a part of the GMU, even though they are not". It's a (good) software representation of the GMU_CX and GMU_GX register spaces within the GPUSS that helps us programatically treat these de-facto GMU-less parts in a way that's very similar to their GMU-equipped cousins, massively saving up on code duplication.

The "wrapper" register space was specifically designed to mimic the layout of a real GMU, though it rather obviously does not have the M3 core et al.

GMU wrapper-equipped A6xx GPUs require clocks and clock-names to be specified under the GPU node, just like their older cousins. Account for that.

---
 .../devicetree/bindings/display/msm/gpu.yaml       | 61 ++++++++++++++++++----
 1 file changed, 52 insertions(+), 9 deletions(-)
Documentation/devicetree/bindings/display/msm/gpu.yaml +52 -9
index 5dabe7b6794b..58ca8912a8c3 100644
@@ -36,10 +36,7 @@ properties:
 
   reg-names:
     minItems: 1
-    items:
-      - const: kgsl_3d0_reg_memory
-      - const: cx_mem
-      - const: cx_dbgc
+    maxItems: 3
 
   interrupts:
     maxItems: 1
@@ -157,16 +154,62 @@ allOf:
       required:
         - clocks
         - clock-names
+
   - if:
       properties:
         compatible:
           contains:
-            pattern: '^qcom,adreno-6[0-9][0-9]\.[0-9]$'
-
-    then: # Since Adreno 6xx series clocks should be defined in GMU
+            enum:
+              - qcom,adreno-610.0
+              - qcom,adreno-619.1
+    then:
       properties:
-        clocks: false
-        clock-names: false
+        clocks:
+          minItems: 6
+          maxItems: 6
+
+        clock-names:
+          items:
+            - const: core
+              description: GPU Core clock
+            - const: iface
+              description: GPU Interface clock
+            - const: mem_iface
+              description: GPU Memory Interface clock
+            - const: alt_mem_iface
+              description: GPU Alternative Memory Interface clock
+            - const: gmu
+              description: CX GMU clock
+            - const: xo
+              description: GPUCC clocksource clock
+
+        reg-names:
+          minItems: 1
+          items:
+            - const: kgsl_3d0_reg_memory
+            - const: cx_dbgc
+
+      required:
+        - clocks
+        - clock-names
+    else:
+      if:
+        properties:
+          compatible:
+            contains:
+              pattern: '^qcom,adreno-6[0-9][0-9]\.[0-9]$'
+
+      then: # Starting with A6xx, the clocks are usually defined in the GMU node
+        properties:
+          clocks: false
+          clock-names: false
+
+          reg-names:
+            minItems: 1
+            items:
+              - const: kgsl_3d0_reg_memory
+              - const: cx_mem
+              - const: cx_dbgc
 
 examples:
   - |
Signature · 1 line
2.40.1
#2 lore raw

PATCH v7 2/18 dt-bindings: display/msm/gmu: Add GMU wrapper

In reply to Konrad Dybcio

The "GMU Wrapper" is Qualcomm's name for "let's treat the GPU blocks we'd normally assign to the GMU as if they were a part of the GMU, even though they are not". It's a (good) software representation of the GMU_CX and GMU_GX register spaces within the GPUSS that helps us programatically treat these de-facto GMU-less parts in a way that's very similar to their GMU-equipped cousins, massively saving up on code duplication.

The "wrapper" register space was specifically designed to mimic the layout of a real GMU, though it rather obviously does not have the M3 core et al.

To sum it all up, the GMU wrapper is essentially a register space within the GPU, which Linux sees as a dumbed-down regular GMU: there's no clocks, interrupts, multiple reg spaces, iommus and OPP. Document it.

---
 .../devicetree/bindings/display/msm/gmu.yaml       | 50 ++++++++++++++++------
 1 file changed, 38 insertions(+), 12 deletions(-)
Documentation/devicetree/bindings/display/msm/gmu.yaml +38 -12
index 029d72822d8b..e36c40b935de 100644
@@ -19,16 +19,18 @@ description: |
 
 properties:
   compatible:
-    items:
-      - pattern: '^qcom,adreno-gmu-6[0-9][0-9]\.[0-9]$'
-      - const: qcom,adreno-gmu
+    oneOf:
+      - items:
+          - pattern: '^qcom,adreno-gmu-6[0-9][0-9]\.[0-9]$'
+          - const: qcom,adreno-gmu
+      - const: qcom,adreno-gmu-wrapper
 
   reg:
-    minItems: 3
+    minItems: 1
     maxItems: 4
 
   reg-names:
-    minItems: 3
+    minItems: 1
     maxItems: 4
 
   clocks:
@@ -44,7 +46,6 @@ properties:
       - description: GMU HFI interrupt
       - description: GMU interrupt
 
-
   interrupt-names:
     items:
       - const: hfi
@@ -72,14 +73,8 @@ required:
   - compatible
   - reg
   - reg-names
-  - clocks
-  - clock-names
-  - interrupts
-  - interrupt-names
   - power-domains
   - power-domain-names
-  - iommus
-  - operating-points-v2
 
 additionalProperties: false
 
@@ -217,6 +212,28 @@ allOf:
             - const: axi
             - const: memnoc
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: qcom,adreno-gmu-wrapper
+    then:
+      properties:
+        reg:
+          items:
+            - description: GMU wrapper register space
+        reg-names:
+          items:
+            - const: gmu
+    else:
+      required:
+        - clocks
+        - clock-names
+        - interrupts
+        - interrupt-names
+        - iommus
+        - operating-points-v2
+
 examples:
   - |
     #include <dt-bindings/clock/qcom,gpucc-sdm845.h>
@@ -249,3 +266,12 @@ examples:
         iommus = <&adreno_smmu 5>;
         operating-points-v2 = <&gmu_opp_table>;
     };
+
+    gmu_wrapper: gmu@596a000 {
+        compatible = "qcom,adreno-gmu-wrapper";
+        reg = <0x0596a000 0x30000>;
+        reg-names = "gmu";
+        power-domains = <&gpucc GPU_CX_GDSC>,
+                        <&gpucc GPU_GX_GDSC>;
+        power-domain-names = "cx", "gx";
+    };
Signature · 1 line
2.40.1
#3 lore raw

PATCH v7 3/18 drm/msm/a6xx: Remove static keyword from sptprac en/disable functions

In reply to Konrad Dybcio

These two will be reused by at least A619_holi in the non-gmu paths. Turn them non-static them to make it possible.

---
 drivers/gpu/drm/msm/adreno/a6xx_gmu.c | 4 ++--
 drivers/gpu/drm/msm/adreno/a6xx_gmu.h | 2 ++
 2 files changed, 4 insertions(+), 2 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gmu.c +2 -2
index e16b4b3f8535..87babbb2a19f 100644
@@ -354,7 +354,7 @@ void a6xx_gmu_clear_oob(struct a6xx_gmu *gmu, enum a6xx_gmu_oob_state state)
 }
 
 /* Enable CPU control of SPTP power power collapse */
-static int a6xx_sptprac_enable(struct a6xx_gmu *gmu)
+int a6xx_sptprac_enable(struct a6xx_gmu *gmu)
 {
 	int ret;
 	u32 val;
@@ -376,7 +376,7 @@ static int a6xx_sptprac_enable(struct a6xx_gmu *gmu)
 }
 
 /* Disable CPU control of SPTP power power collapse */
-static void a6xx_sptprac_disable(struct a6xx_gmu *gmu)
+void a6xx_sptprac_disable(struct a6xx_gmu *gmu)
 {
 	u32 val;
 	int ret;
drivers/gpu/drm/msm/adreno/a6xx_gmu.h +2 -0
index 0bc3eb443fec..7ee5b606bc47 100644
@@ -193,5 +193,7 @@ int a6xx_hfi_set_freq(struct a6xx_gmu *gmu, int index);
 
 bool a6xx_gmu_gx_is_on(struct a6xx_gmu *gmu);
 bool a6xx_gmu_sptprac_is_on(struct a6xx_gmu *gmu);
+void a6xx_sptprac_disable(struct a6xx_gmu *gmu);
+int a6xx_sptprac_enable(struct a6xx_gmu *gmu);
 
 #endif
Signature · 1 line
2.40.1
#4 lore raw

PATCH v7 4/18 drm/msm/a6xx: Move force keepalive vote removal to a6xx_gmu_force_off()

In reply to Konrad Dybcio

As pointed out by Akhil during the review process of GMU wrapper introduction [1], it makes sense to move this write into the function that's responsible for forcibly shutting the GMU off.

It is also very convenient to move this to GMU-specific code, so that it does not have to be guarded by an if-condition to avoid calling it on GMU wrapper targets.

Move the write to the aforementioned a6xx_gmu_force_off() to achieve that. No effective functional change.

[1] https://lore.kernel.org/linux-arm-msm/[email protected]/

---
 drivers/gpu/drm/msm/adreno/a6xx_gmu.c | 6 ++++++
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 6 ------
 2 files changed, 6 insertions(+), 6 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gmu.c +6 -0
index 87babbb2a19f..9421716a2fe5 100644
@@ -912,6 +912,12 @@ static void a6xx_gmu_force_off(struct a6xx_gmu *gmu)
 	struct adreno_gpu *adreno_gpu = &a6xx_gpu->base;
 	struct msm_gpu *gpu = &adreno_gpu->base;
 
+	/*
+	 * Turn off keep alive that might have been enabled by the hang
+	 * interrupt
+	 */
+	gmu_write(&a6xx_gpu->gmu, REG_A6XX_GMU_GMU_PWR_COL_KEEPALIVE, 0);
+
 	/* Flush all the queues */
 	a6xx_hfi_stop(gmu);
 
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +0 -6
index 9fb214f150dd..e34aa15156a4 100644
@@ -1274,12 +1274,6 @@ static void a6xx_recover(struct msm_gpu *gpu)
 	/* Halt SQE first */
 	gpu_write(gpu, REG_A6XX_CP_SQE_CNTL, 3);
 
-	/*
-	 * Turn off keep alive that might have been enabled by the hang
-	 * interrupt
-	 */
-	gmu_write(&a6xx_gpu->gmu, REG_A6XX_GMU_GMU_PWR_COL_KEEPALIVE, 0);
-
 	pm_runtime_dont_use_autosuspend(&gpu->pdev->dev);
 
 	/* active_submit won't change until we make a submission */
Signature · 1 line
2.40.1
#5 lore raw

PATCH v7 5/18 drm/msm/a6xx: Move a6xx_bus_clear_pending_transactions to a6xx_gpu

In reply to Konrad Dybcio

This function is responsible for telling the GPU to halt transactions on all of its relevant buses, drain them and leave them in a predictable state, so that the GPU can be e.g. reset cleanly.

Move the function to a6xx_gpu.c, remove the static keyword and add a prototype in a6xx_gpu.h to accomodate for the move.

---
 drivers/gpu/drm/msm/adreno/a6xx_gmu.c | 37 -----------------------------------
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 36 ++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/msm/adreno/a6xx_gpu.h |  2 ++
 3 files changed, 38 insertions(+), 37 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gmu.c +0 -37
index 9421716a2fe5..b86be123ecd0 100644
@@ -868,43 +868,6 @@ static void a6xx_gmu_rpmh_off(struct a6xx_gmu *gmu)
 		(val & 1), 100, 1000);
 }
 
-#define GBIF_CLIENT_HALT_MASK             BIT(0)
-#define GBIF_ARB_HALT_MASK                BIT(1)
-
-static void a6xx_bus_clear_pending_transactions(struct adreno_gpu *adreno_gpu,
-		bool gx_off)
-{
-	struct msm_gpu *gpu = &adreno_gpu->base;
-
-	if (!a6xx_has_gbif(adreno_gpu)) {
-		gpu_write(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL0, 0xf);
-		spin_until((gpu_read(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL1) &
-								0xf) == 0xf);
-		gpu_write(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL0, 0);
-
-		return;
-	}
-
-	if (gx_off) {
-		/* Halt the gx side of GBIF */
-		gpu_write(gpu, REG_A6XX_RBBM_GBIF_HALT, 1);
-		spin_until(gpu_read(gpu, REG_A6XX_RBBM_GBIF_HALT_ACK) & 1);
-	}
-
-	/* Halt new client requests on GBIF */
-	gpu_write(gpu, REG_A6XX_GBIF_HALT, GBIF_CLIENT_HALT_MASK);
-	spin_until((gpu_read(gpu, REG_A6XX_GBIF_HALT_ACK) &
-			(GBIF_CLIENT_HALT_MASK)) == GBIF_CLIENT_HALT_MASK);
-
-	/* Halt all AXI requests on GBIF */
-	gpu_write(gpu, REG_A6XX_GBIF_HALT, GBIF_ARB_HALT_MASK);
-	spin_until((gpu_read(gpu,  REG_A6XX_GBIF_HALT_ACK) &
-			(GBIF_ARB_HALT_MASK)) == GBIF_ARB_HALT_MASK);
-
-	/* The GBIF halt needs to be explicitly cleared */
-	gpu_write(gpu, REG_A6XX_GBIF_HALT, 0x0);
-}
-
 /* Force the GMU off in case it isn't responsive */
 static void a6xx_gmu_force_off(struct a6xx_gmu *gmu)
 {
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +36 -0
index e34aa15156a4..6bb4da70f6a6 100644
@@ -1597,6 +1597,42 @@ static void a6xx_llc_slices_init(struct platform_device *pdev,
 		a6xx_gpu->llc_mmio = ERR_PTR(-EINVAL);
 }
 
+#define GBIF_CLIENT_HALT_MASK             BIT(0)
+#define GBIF_ARB_HALT_MASK                BIT(1)
+
+void a6xx_bus_clear_pending_transactions(struct adreno_gpu *adreno_gpu, bool gx_off)
+{
+	struct msm_gpu *gpu = &adreno_gpu->base;
+
+	if (!a6xx_has_gbif(adreno_gpu)) {
+		gpu_write(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL0, 0xf);
+		spin_until((gpu_read(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL1) &
+								0xf) == 0xf);
+		gpu_write(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL0, 0);
+
+		return;
+	}
+
+	if (gx_off) {
+		/* Halt the gx side of GBIF */
+		gpu_write(gpu, REG_A6XX_RBBM_GBIF_HALT, 1);
+		spin_until(gpu_read(gpu, REG_A6XX_RBBM_GBIF_HALT_ACK) & 1);
+	}
+
+	/* Halt new client requests on GBIF */
+	gpu_write(gpu, REG_A6XX_GBIF_HALT, GBIF_CLIENT_HALT_MASK);
+	spin_until((gpu_read(gpu, REG_A6XX_GBIF_HALT_ACK) &
+			(GBIF_CLIENT_HALT_MASK)) == GBIF_CLIENT_HALT_MASK);
+
+	/* Halt all AXI requests on GBIF */
+	gpu_write(gpu, REG_A6XX_GBIF_HALT, GBIF_ARB_HALT_MASK);
+	spin_until((gpu_read(gpu,  REG_A6XX_GBIF_HALT_ACK) &
+			(GBIF_ARB_HALT_MASK)) == GBIF_ARB_HALT_MASK);
+
+	/* The GBIF halt needs to be explicitly cleared */
+	gpu_write(gpu, REG_A6XX_GBIF_HALT, 0x0);
+}
+
 static int a6xx_pm_resume(struct msm_gpu *gpu)
 {
 	struct adreno_gpu *adreno_gpu = to_adreno_gpu(gpu);
drivers/gpu/drm/msm/adreno/a6xx_gpu.h +2 -0
index eea2e60ce3b7..9580def06d45 100644
@@ -88,4 +88,6 @@ void a6xx_show(struct msm_gpu *gpu, struct msm_gpu_state *state,
 struct msm_gpu_state *a6xx_gpu_state_get(struct msm_gpu *gpu);
 int a6xx_gpu_state_put(struct msm_gpu_state *state);
 
+void a6xx_bus_clear_pending_transactions(struct adreno_gpu *adreno_gpu, bool gx_off);
+
 #endif /* __A6XX_GPU_H__ */
Signature · 1 line
2.40.1
#6 lore raw

PATCH v7 6/18 drm/msm/a6xx: Improve a6xx_bus_clear_pending_transactions()

In reply to Konrad Dybcio

Unify the indentation and explain the cryptic 0xF value.

---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +5 -4
index 6bb4da70f6a6..e3ac3f045665 100644
@@ -1597,17 +1597,18 @@ static void a6xx_llc_slices_init(struct platform_device *pdev,
 		a6xx_gpu->llc_mmio = ERR_PTR(-EINVAL);
 }
 
-#define GBIF_CLIENT_HALT_MASK             BIT(0)
-#define GBIF_ARB_HALT_MASK                BIT(1)
+#define GBIF_CLIENT_HALT_MASK		BIT(0)
+#define GBIF_ARB_HALT_MASK		BIT(1)
+#define VBIF_XIN_HALT_CTRL0_MASK	GENMASK(3, 0)
 
 void a6xx_bus_clear_pending_transactions(struct adreno_gpu *adreno_gpu, bool gx_off)
 {
 	struct msm_gpu *gpu = &adreno_gpu->base;
 
 	if (!a6xx_has_gbif(adreno_gpu)) {
-		gpu_write(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL0, 0xf);
+		gpu_write(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL0, VBIF_XIN_HALT_CTRL0_MASK);
 		spin_until((gpu_read(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL1) &
-								0xf) == 0xf);
+				(VBIF_XIN_HALT_CTRL0_MASK)) == VBIF_XIN_HALT_CTRL0_MASK);
 		gpu_write(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL0, 0);
 
 		return;
Signature · 1 line
2.40.1
#7 lore raw

PATCH v7 7/18 drm/msm/a6xx: Add a helper for software-resetting the GPU

In reply to Konrad Dybcio

Introduce a6xx_gpu_sw_reset() in preparation for adding GMU wrapper GPUs and reuse it in a6xx_gmu_force_off().

This helper, contrary to the original usage in GMU code paths, adds a write memory barrier which together with the necessary delay should ensure that the reset is never deasserted too quickly due to e.g. OoO execution going crazy.

---
 drivers/gpu/drm/msm/adreno/a6xx_gmu.c |  3 +--
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 11 +++++++++++
 drivers/gpu/drm/msm/adreno/a6xx_gpu.h |  1 +
 3 files changed, 13 insertions(+), 2 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gmu.c +1 -2
index b86be123ecd0..5ba8cba69383 100644
@@ -899,8 +899,7 @@ static void a6xx_gmu_force_off(struct a6xx_gmu *gmu)
 	a6xx_bus_clear_pending_transactions(adreno_gpu, true);
 
 	/* Reset GPU core blocks */
-	gpu_write(gpu, REG_A6XX_RBBM_SW_RESET_CMD, 1);
-	udelay(100);
+	a6xx_gpu_sw_reset(gpu, true);
 }
 
 static void a6xx_gmu_set_initial_freq(struct msm_gpu *gpu, struct a6xx_gmu *gmu)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +11 -0
index e3ac3f045665..083ccb5bcb4e 100644
@@ -1634,6 +1634,17 @@ void a6xx_bus_clear_pending_transactions(struct adreno_gpu *adreno_gpu, bool gx_
 	gpu_write(gpu, REG_A6XX_GBIF_HALT, 0x0);
 }
 
+void a6xx_gpu_sw_reset(struct msm_gpu *gpu, bool assert)
+{
+	gpu_write(gpu, REG_A6XX_RBBM_SW_RESET_CMD, assert);
+	/* Add a barrier to avoid bad surprises */
+	mb();
+
+	/* The reset line needs to be asserted for at least 100 us */
+	if (assert)
+		udelay(100);
+}
+
 static int a6xx_pm_resume(struct msm_gpu *gpu)
 {
 	struct adreno_gpu *adreno_gpu = to_adreno_gpu(gpu);
drivers/gpu/drm/msm/adreno/a6xx_gpu.h +1 -0
index 9580def06d45..aa70390ee1c6 100644
@@ -89,5 +89,6 @@ struct msm_gpu_state *a6xx_gpu_state_get(struct msm_gpu *gpu);
 int a6xx_gpu_state_put(struct msm_gpu_state *state);
 
 void a6xx_bus_clear_pending_transactions(struct adreno_gpu *adreno_gpu, bool gx_off);
+void a6xx_gpu_sw_reset(struct msm_gpu *gpu, bool assert);
 
 #endif /* __A6XX_GPU_H__ */
Signature · 1 line
2.40.1
#8 lore raw

PATCH v7 8/18 drm/msm/a6xx: Remove both GBIF and RBBM GBIF halt on hw init

In reply to Konrad Dybcio

Currently we're only deasserting REG_A6XX_RBBM_GBIF_HALT, but we also need REG_A6XX_GBIF_HALT to be set to 0.

This is typically done automatically on successful GX collapse, but in case that fails, we should take care of it.

Also, add a memory barrier to ensure it's gone through before jumping to further initialization.

---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +5 -1
index 083ccb5bcb4e..dfde5fb65eed 100644
@@ -1003,8 +1003,12 @@ static int hw_init(struct msm_gpu *gpu)
 	a6xx_gmu_set_oob(&a6xx_gpu->gmu, GMU_OOB_GPU_SET);
 
 	/* Clear GBIF halt in case GX domain was not collapsed */
-	if (a6xx_has_gbif(adreno_gpu))
+	if (a6xx_has_gbif(adreno_gpu)) {
+		gpu_write(gpu, REG_A6XX_GBIF_HALT, 0);
 		gpu_write(gpu, REG_A6XX_RBBM_GBIF_HALT, 0);
+		/* Let's make extra sure that the GPU can access the memory.. */
+		mb();
+	}
 
 	gpu_write(gpu, REG_A6XX_RBBM_SECVID_TSB_CNTL, 0);
 
Signature · 1 line
2.40.1
#9 lore raw

PATCH v7 9/18 drm/msm/a6xx: Extend and explain UBWC config

In reply to Konrad Dybcio

Rename lower_bit to hbb_lo and explain what it signifies. Add explanations (wherever possible to other tunables).

Port setting min_access_length, ubwc_mode and hbb_hi from downstream.

---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 39 +++++++++++++++++++++++++++--------
 1 file changed, 30 insertions(+), 9 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +30 -9
index dfde5fb65eed..58bf405b85d8 100644
@@ -786,10 +786,25 @@ static void a6xx_set_cp_protect(struct msm_gpu *gpu)
 static void a6xx_set_ubwc_config(struct msm_gpu *gpu)
 {
 	struct adreno_gpu *adreno_gpu = to_adreno_gpu(gpu);
-	u32 lower_bit = 2;
-	u32 amsbc = 0;
+	/* Unknown, introduced with A650 family, related to UBWC mode/ver 4 */
 	u32 rgb565_predicator = 0;
+	/* Unknown, introduced with A650 family */
 	u32 uavflagprd_inv = 0;
+	/* Whether the minimum access length is 64 bits */
+	u32 min_acc_len = 0;
+	/* Entirely magic, per-GPU-gen value */
+	u32 ubwc_mode = 0;
+	/*
+	 * The Highest Bank Bit value represents the bit of the highest DDR bank.
+	 * We then subtract 13 from it (13 is the minimum value allowed by hw) and
+	 * write the lowest two bits of the remaining value as hbb_lo and the
+	 * one above it as hbb_hi to the hardware. This should ideally use DRAM
+	 * type detection.
+	 */
+	u32 hbb_hi = 0;
+	u32 hbb_lo = 2;
+	/* Unknown, introduced with A640/680 */
+	u32 amsbc = 0;
 
 	/* a618 is using the hw default values */
 	if (adreno_is_a618(adreno_gpu))
@@ -800,25 +815,31 @@ static void a6xx_set_ubwc_config(struct msm_gpu *gpu)
 
 	if (adreno_is_a650(adreno_gpu) || adreno_is_a660(adreno_gpu)) {
 		/* TODO: get ddr type from bootloader and use 2 for LPDDR4 */
-		lower_bit = 3;
+		hbb_lo = 3;
 		amsbc = 1;
 		rgb565_predicator = 1;
 		uavflagprd_inv = 2;
 	}
 
 	if (adreno_is_7c3(adreno_gpu)) {
-		lower_bit = 1;
+		hbb_lo = 1;
 		amsbc = 1;
 		rgb565_predicator = 1;
 		uavflagprd_inv = 2;
 	}
 
 	gpu_write(gpu, REG_A6XX_RB_NC_MODE_CNTL,
-		rgb565_predicator << 11 | amsbc << 4 | lower_bit << 1);
-	gpu_write(gpu, REG_A6XX_TPL1_NC_MODE_CNTL, lower_bit << 1);
-	gpu_write(gpu, REG_A6XX_SP_NC_MODE_CNTL,
-		uavflagprd_inv << 4 | lower_bit << 1);
-	gpu_write(gpu, REG_A6XX_UCHE_MODE_CNTL, lower_bit << 21);
+		  rgb565_predicator << 11 | hbb_hi << 10 | amsbc << 4 |
+		  min_acc_len << 3 | hbb_lo << 1 | ubwc_mode);
+
+	gpu_write(gpu, REG_A6XX_TPL1_NC_MODE_CNTL, hbb_hi << 4 |
+		  min_acc_len << 3 | hbb_lo << 1 | ubwc_mode);
+
+	gpu_write(gpu, REG_A6XX_SP_NC_MODE_CNTL, hbb_hi << 10 |
+		  uavflagprd_inv << 4 | min_acc_len << 3 |
+		  hbb_lo << 1 | ubwc_mode);
+
+	gpu_write(gpu, REG_A6XX_UCHE_MODE_CNTL, min_acc_len << 23 | hbb_lo << 21);
 }
 
 static int a6xx_cp_init(struct msm_gpu *gpu)
Signature · 1 line
2.40.1
#10 lore raw

PATCH v7 10/18 drm/msm/a6xx: Introduce GMU wrapper support

In reply to Konrad Dybcio

Some (particularly SMD_RPM, a.k.a non-RPMh) SoCs implement A6XX GPUs but don't implement the associated GMUs. This is due to the fact that the GMU directly pokes at RPMh. Sadly, this means we have to take care of enabling & scaling power rails, clocks and bandwidth ourselves.

Reuse existing Adreno-common code and modify the deeply-GMU-infused A6XX code to facilitate these GPUs. This involves if-ing out lots of GMU callbacks and introducing a new type of GMU - GMU wrapper (it's the actual name that Qualcomm uses in their downstream kernels).

This is essentially a register region which is convenient to model as a device. We'll use it for managing the GDSCs. The register layout matches the actual GMU_CX/GX regions on the "real GMU" devices and lets us reuse quite a bit of gmu_read/write/rmw calls.

---
 drivers/gpu/drm/msm/adreno/a6xx_gmu.c       |  72 +++++++++-
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c       | 215 ++++++++++++++++++++++++----
 drivers/gpu/drm/msm/adreno/a6xx_gpu.h       |   1 +
 drivers/gpu/drm/msm/adreno/a6xx_gpu_state.c |  14 +-
 drivers/gpu/drm/msm/adreno/adreno_gpu.c     |   8 +-
 drivers/gpu/drm/msm/adreno/adreno_gpu.h     |   6 +
 6 files changed, 281 insertions(+), 35 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gmu.c +69 -3
index 5ba8cba69383..385ca3a12462 100644
@@ -1437,6 +1437,7 @@ static int a6xx_gmu_get_irq(struct a6xx_gmu *gmu, struct platform_device *pdev,
 
 void a6xx_gmu_remove(struct a6xx_gpu *a6xx_gpu)
 {
+	struct adreno_gpu *adreno_gpu = &a6xx_gpu->base;
 	struct a6xx_gmu *gmu = &a6xx_gpu->gmu;
 	struct platform_device *pdev = to_platform_device(gmu->dev);
 
@@ -1462,10 +1463,12 @@ void a6xx_gmu_remove(struct a6xx_gpu *a6xx_gpu)
 	gmu->mmio = NULL;
 	gmu->rscc = NULL;
 
-	a6xx_gmu_memory_free(gmu);
+	if (!adreno_has_gmu_wrapper(adreno_gpu)) {
+		a6xx_gmu_memory_free(gmu);
 
-	free_irq(gmu->gmu_irq, gmu);
-	free_irq(gmu->hfi_irq, gmu);
+		free_irq(gmu->gmu_irq, gmu);
+		free_irq(gmu->hfi_irq, gmu);
+	}
 
 	/* Drop reference taken in of_find_device_by_node */
 	put_device(gmu->dev);
@@ -1484,6 +1487,69 @@ static int cxpd_notifier_cb(struct notifier_block *nb,
 	return 0;
 }
 
+int a6xx_gmu_wrapper_init(struct a6xx_gpu *a6xx_gpu, struct device_node *node)
+{
+	struct platform_device *pdev = of_find_device_by_node(node);
+	struct a6xx_gmu *gmu = &a6xx_gpu->gmu;
+	int ret;
+
+	if (!pdev)
+		return -ENODEV;
+
+	gmu->dev = &pdev->dev;
+
+	of_dma_configure(gmu->dev, node, true);
+
+	pm_runtime_enable(gmu->dev);
+
+	/* Mark legacy for manual SPTPRAC control */
+	gmu->legacy = true;
+
+	/* Map the GMU registers */
+	gmu->mmio = a6xx_gmu_get_mmio(pdev, "gmu");
+	if (IS_ERR(gmu->mmio)) {
+		ret = PTR_ERR(gmu->mmio);
+		goto err_mmio;
+	}
+
+	gmu->cxpd = dev_pm_domain_attach_by_name(gmu->dev, "cx");
+	if (IS_ERR(gmu->cxpd)) {
+		ret = PTR_ERR(gmu->cxpd);
+		goto err_mmio;
+	}
+
+	if (!device_link_add(gmu->dev, gmu->cxpd, DL_FLAG_PM_RUNTIME)) {
+		ret = -ENODEV;
+		goto detach_cxpd;
+	}
+
+	init_completion(&gmu->pd_gate);
+	complete_all(&gmu->pd_gate);
+	gmu->pd_nb.notifier_call = cxpd_notifier_cb;
+
+	/* Get a link to the GX power domain to reset the GPU */
+	gmu->gxpd = dev_pm_domain_attach_by_name(gmu->dev, "gx");
+	if (IS_ERR(gmu->gxpd)) {
+		ret = PTR_ERR(gmu->gxpd);
+		goto err_mmio;
+	}
+
+	gmu->initialized = true;
+
+	return 0;
+
+detach_cxpd:
+	dev_pm_domain_detach(gmu->cxpd, false);
+
+err_mmio:
+	iounmap(gmu->mmio);
+
+	/* Drop reference taken in of_find_device_by_node */
+	put_device(gmu->dev);
+
+	return ret;
+}
+
 int a6xx_gmu_init(struct a6xx_gpu *a6xx_gpu, struct device_node *node)
 {
 	struct adreno_gpu *adreno_gpu = &a6xx_gpu->base;
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +191 -24

333 lines not on this page · raw message

drivers/gpu/drm/msm/adreno/a6xx_gpu.h +1 -0
index aa70390ee1c6..c788b06e72da 100644
@@ -76,6 +76,7 @@ int a6xx_gmu_set_oob(struct a6xx_gmu *gmu, enum a6xx_gmu_oob_state state);
 void a6xx_gmu_clear_oob(struct a6xx_gmu *gmu, enum a6xx_gmu_oob_state state);
 
 int a6xx_gmu_init(struct a6xx_gpu *a6xx_gpu, struct device_node *node);
+int a6xx_gmu_wrapper_init(struct a6xx_gpu *a6xx_gpu, struct device_node *node);
 void a6xx_gmu_remove(struct a6xx_gpu *a6xx_gpu);
 
 void a6xx_gmu_set_freq(struct msm_gpu *gpu, struct dev_pm_opp *opp,
drivers/gpu/drm/msm/adreno/a6xx_gpu_state.c +8 -6
index 30ecdff363e7..4e5d650578c6 100644
@@ -1041,16 +1041,18 @@ struct msm_gpu_state *a6xx_gpu_state_get(struct msm_gpu *gpu)
 	/* Get the generic state from the adreno core */
 	adreno_gpu_state_get(gpu, &a6xx_state->base);
 
-	a6xx_get_gmu_registers(gpu, a6xx_state);
+	if (!adreno_has_gmu_wrapper(adreno_gpu)) {
+		a6xx_get_gmu_registers(gpu, a6xx_state);
 
-	a6xx_state->gmu_log = a6xx_snapshot_gmu_bo(a6xx_state, &a6xx_gpu->gmu.log);
-	a6xx_state->gmu_hfi = a6xx_snapshot_gmu_bo(a6xx_state, &a6xx_gpu->gmu.hfi);
-	a6xx_state->gmu_debug = a6xx_snapshot_gmu_bo(a6xx_state, &a6xx_gpu->gmu.debug);
+		a6xx_state->gmu_log = a6xx_snapshot_gmu_bo(a6xx_state, &a6xx_gpu->gmu.log);
+		a6xx_state->gmu_hfi = a6xx_snapshot_gmu_bo(a6xx_state, &a6xx_gpu->gmu.hfi);
+		a6xx_state->gmu_debug = a6xx_snapshot_gmu_bo(a6xx_state, &a6xx_gpu->gmu.debug);
 
-	a6xx_snapshot_gmu_hfi_history(gpu, a6xx_state);
+		a6xx_snapshot_gmu_hfi_history(gpu, a6xx_state);
+	}
 
 	/* If GX isn't on the rest of the data isn't going to be accessible */
-	if (!a6xx_gmu_gx_is_on(&a6xx_gpu->gmu))
+	if (!adreno_has_gmu_wrapper(adreno_gpu) && !a6xx_gmu_gx_is_on(&a6xx_gpu->gmu))
 		return &a6xx_state->base;
 
 	/* Get the banks of indexed registers */
drivers/gpu/drm/msm/adreno/adreno_gpu.c +6 -2
index 6934cee07d42..5c5901d65950 100644
@@ -528,6 +528,10 @@ int adreno_load_fw(struct adreno_gpu *adreno_gpu)
 		if (!adreno_gpu->info->fw[i])
 			continue;
 
+		/* Skip loading GMU firwmare with GMU Wrapper */
+		if (adreno_has_gmu_wrapper(adreno_gpu) && i == ADRENO_FW_GMU)
+			continue;
+
 		/* Skip if the firmware has already been loaded */
 		if (adreno_gpu->fw[i])
 			continue;
@@ -1074,8 +1078,8 @@ int adreno_gpu_init(struct drm_device *drm, struct platform_device *pdev,
 	u32 speedbin;
 	int ret;
 
-	/* Only handle the core clock when GMU is not in use */
-	if (config->rev.core < 6) {
+	/* Only handle the core clock when GMU is not in use (or is absent). */
+	if (adreno_has_gmu_wrapper(adreno_gpu) || config->rev.core < 6) {
 		/*
 		 * This can only be done before devm_pm_opp_of_add_table(), or
 		 * dev_pm_opp_set_config() will WARN_ON()
drivers/gpu/drm/msm/adreno/adreno_gpu.h +6 -0
index f62612a5c70f..ee5352bc5329 100644
@@ -115,6 +115,7 @@ struct adreno_gpu {
 	 * code (a3xx_gpu.c) and stored in this common location.
 	 */
 	const unsigned int *reg_offsets;
+	bool gmu_is_wrapper;
 };
 #define to_adreno_gpu(x) container_of(x, struct adreno_gpu, base)
 
@@ -145,6 +146,11 @@ struct adreno_platform_config {
 
 bool adreno_cmp_rev(struct adreno_rev rev1, struct adreno_rev rev2);
 
+static inline bool adreno_has_gmu_wrapper(struct adreno_gpu *gpu)
+{
+	return gpu->gmu_is_wrapper;
+}
+
 static inline bool adreno_is_a2xx(struct adreno_gpu *gpu)
 {
 	return (gpu->revn < 300);
Signature · 1 line
2.40.1
#11 lore raw

PATCH v7 11/18 drm/msm/adreno: Disable has_cached_coherent in GMU wrapper configurations

In reply to Konrad Dybcio

A610 and A619_holi don't support the feature. Disable it to make the GPU stop crashing after almost each and every submission - the received data on the GPU end was simply incomplete in garbled, resulting in almost nothing being executed properly. Extend the disablement to adreno_has_gmu_wrapper, as none of the GMU wrapper Adrenos that don't support yet seem to feature it.

---
 drivers/gpu/drm/msm/adreno/adreno_device.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/gpu/drm/msm/adreno/adreno_device.c +4 -1
index 8cff86e9d35c..b133755a56c4 100644
@@ -551,7 +551,6 @@ static int adreno_bind(struct device *dev, struct device *master, void *data)
 		config.rev.minor, config.rev.patchid);
 
 	priv->is_a2xx = config.rev.core == 2;
-	priv->has_cached_coherent = config.rev.core >= 6;
 
 	gpu = info->init(drm);
 	if (IS_ERR(gpu)) {
@@ -563,6 +562,10 @@ static int adreno_bind(struct device *dev, struct device *master, void *data)
 	if (ret)
 		return ret;
 
+	if (config.rev.core >= 6)
+		if (!adreno_has_gmu_wrapper(to_adreno_gpu(gpu)))
+			priv->has_cached_coherent = true;
+
 	return 0;
 }
 
Signature · 1 line
2.40.1
#12 lore raw

PATCH v7 12/18 drm/msm/a6xx: Add support for A619_holi

In reply to Konrad Dybcio

A619_holi is a GMU-less variant of the already-supported A619 GPU. It's present on at least SM4350 (holi) and SM6375 (blair). No mesa changes are required. Add the required kernel-side support for it.

---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c   | 27 +++++++++++++++++++++++++--
 drivers/gpu/drm/msm/adreno/adreno_gpu.h |  5 +++++
 2 files changed, 30 insertions(+), 2 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +25 -2
index 2ba9d790a52c..7eaebcefcb2a 100644
@@ -810,6 +810,9 @@ static void a6xx_set_ubwc_config(struct msm_gpu *gpu)
 	if (adreno_is_a618(adreno_gpu))
 		return;
 
+	if (adreno_is_a619_holi(adreno_gpu))
+		hbb_lo = 0;
+
 	if (adreno_is_a640_family(adreno_gpu))
 		amsbc = 1;
 
@@ -1027,7 +1030,12 @@ static int hw_init(struct msm_gpu *gpu)
 	}
 
 	/* Clear GBIF halt in case GX domain was not collapsed */
-	if (a6xx_has_gbif(adreno_gpu)) {
+	if (adreno_is_a619_holi(adreno_gpu)) {
+		gpu_write(gpu, REG_A6XX_GBIF_HALT, 0);
+		gpu_write(gpu, REG_A6XX_RBBM_GPR0_CNTL, 0);
+		/* Let's make extra sure that the GPU can access the memory.. */
+		mb();
+	} else if (a6xx_has_gbif(adreno_gpu)) {
 		gpu_write(gpu, REG_A6XX_GBIF_HALT, 0);
 		gpu_write(gpu, REG_A6XX_RBBM_GBIF_HALT, 0);
 		/* Let's make extra sure that the GPU can access the memory.. */
@@ -1036,6 +1044,9 @@ static int hw_init(struct msm_gpu *gpu)
 
 	gpu_write(gpu, REG_A6XX_RBBM_SECVID_TSB_CNTL, 0);
 
+	if (adreno_is_a619_holi(adreno_gpu))
+		a6xx_sptprac_enable(gmu);
+
 	/*
 	 * Disable the trusted memory range - we don't actually supported secure
 	 * memory rendering at this point in time and we don't want to block off
@@ -1656,12 +1667,18 @@ static void a6xx_llc_slices_init(struct platform_device *pdev,
 #define GBIF_CLIENT_HALT_MASK		BIT(0)
 #define GBIF_ARB_HALT_MASK		BIT(1)
 #define VBIF_XIN_HALT_CTRL0_MASK	GENMASK(3, 0)
+#define VBIF_RESET_ACK_MASK		0xF0
+#define GPR0_GBIF_HALT_REQUEST		0x1E0
 
 void a6xx_bus_clear_pending_transactions(struct adreno_gpu *adreno_gpu, bool gx_off)
 {
 	struct msm_gpu *gpu = &adreno_gpu->base;
 
-	if (!a6xx_has_gbif(adreno_gpu)) {
+	if (adreno_is_a619_holi(adreno_gpu)) {
+		gpu_write(gpu, 0x18, GPR0_GBIF_HALT_REQUEST);
+		spin_until((gpu_read(gpu, REG_A6XX_RBBM_VBIF_GX_RESET_STATUS) &
+				(VBIF_RESET_ACK_MASK)) == VBIF_RESET_ACK_MASK);
+	} else if (!a6xx_has_gbif(adreno_gpu)) {
 		gpu_write(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL0, VBIF_XIN_HALT_CTRL0_MASK);
 		spin_until((gpu_read(gpu, REG_A6XX_VBIF_XIN_HALT_CTRL1) &
 				(VBIF_XIN_HALT_CTRL0_MASK)) == VBIF_XIN_HALT_CTRL0_MASK);
@@ -1755,6 +1772,9 @@ static int a6xx_pm_resume(struct msm_gpu *gpu)
 	if (ret)
 		goto err_mem_clk;
 
+	if (adreno_is_a619_holi(adreno_gpu))
+		a6xx_sptprac_enable(gmu);
+
 	/* If anything goes south, tear the GPU down piece by piece.. */
 	if (ret) {
 err_mem_clk:
@@ -1818,6 +1838,9 @@ static int a6xx_pm_suspend(struct msm_gpu *gpu)
 	/* Drain the outstanding traffic on memory buses */
 	a6xx_bus_clear_pending_transactions(adreno_gpu, true);
 
+	if (adreno_is_a619_holi(adreno_gpu))
+		a6xx_sptprac_disable(gmu);
+
 	clk_disable_unprepare(gpu->ebi1_clk);
 
 	clk_bulk_disable_unprepare(gpu->nr_clocks, gpu->grp_clks);
drivers/gpu/drm/msm/adreno/adreno_gpu.h +5 -0
index ee5352bc5329..432fee5c1516 100644
@@ -252,6 +252,11 @@ static inline int adreno_is_a619(struct adreno_gpu *gpu)
 	return gpu->revn == 619;
 }
 
+static inline int adreno_is_a619_holi(struct adreno_gpu *gpu)
+{
+	return adreno_is_a619(gpu) && adreno_has_gmu_wrapper(gpu);
+}
+
 static inline int adreno_is_a630(struct adreno_gpu *gpu)
 {
 	return gpu->revn == 630;
Signature · 1 line
2.40.1
#13 lore raw

PATCH v7 13/18 drm/msm/a6xx: Add A610 support

In reply to Konrad Dybcio

A610 is one of (if not the) lowest-tier SKUs in the A6XX family. It features no GMU, as it's implemented solely on SoCs with SMD_RPM. What's more interesting is that it does not feature a VDDGX line either, being powered solely by VDDCX and has an unfortunate hardware quirk that makes its reset line broken - after a couple of assert/ deassert cycles, it will hang for good and will not wake up again.

This GPU requires mesa changes for proper rendering, and lots of them at that. The command streams are quite far away from any other A6XX GPU and hence it needs special care. This patch was validated both by running an (incomplete) downstream mesa with some hacks (frames rendered correctly, though some instructions made the GPU hangcheck which is expected - garbage in, garbage out) and by replaying RD traces captured with the downstream KGSL driver - no crashes there, ever.

Add support for this GPU on the kernel side, which comes down to pretty simply adding A612 HWCG tables, altering a few values and adding a special case for handling the reset line.

---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c      | 101 +++++++++++++++++++++++++----
 drivers/gpu/drm/msm/adreno/adreno_device.c |  12 ++++
 drivers/gpu/drm/msm/adreno/adreno_gpu.h    |   8 ++-
 3 files changed, 108 insertions(+), 13 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +89 -12
index 7eaebcefcb2a..ca055bff23c8 100644
@@ -252,6 +252,56 @@ static void a6xx_submit(struct msm_gpu *gpu, struct msm_gem_submit *submit)
 	a6xx_flush(gpu, ring);
 }
 
+const struct adreno_reglist a612_hwcg[] = {
+	{REG_A6XX_RBBM_CLOCK_CNTL_SP0, 0x22222222},
+	{REG_A6XX_RBBM_CLOCK_CNTL2_SP0, 0x02222220},
+	{REG_A6XX_RBBM_CLOCK_DELAY_SP0, 0x00000081},
+	{REG_A6XX_RBBM_CLOCK_HYST_SP0, 0x0000f3cf},
+	{REG_A6XX_RBBM_CLOCK_CNTL_TP0, 0x22222222},
+	{REG_A6XX_RBBM_CLOCK_CNTL2_TP0, 0x22222222},
+	{REG_A6XX_RBBM_CLOCK_CNTL3_TP0, 0x22222222},
+	{REG_A6XX_RBBM_CLOCK_CNTL4_TP0, 0x00022222},
+	{REG_A6XX_RBBM_CLOCK_DELAY_TP0, 0x11111111},
+	{REG_A6XX_RBBM_CLOCK_DELAY2_TP0, 0x11111111},
+	{REG_A6XX_RBBM_CLOCK_DELAY3_TP0, 0x11111111},
+	{REG_A6XX_RBBM_CLOCK_DELAY4_TP0, 0x00011111},
+	{REG_A6XX_RBBM_CLOCK_HYST_TP0, 0x77777777},
+	{REG_A6XX_RBBM_CLOCK_HYST2_TP0, 0x77777777},
+	{REG_A6XX_RBBM_CLOCK_HYST3_TP0, 0x77777777},
+	{REG_A6XX_RBBM_CLOCK_HYST4_TP0, 0x00077777},
+	{REG_A6XX_RBBM_CLOCK_CNTL_RB0, 0x22222222},
+	{REG_A6XX_RBBM_CLOCK_CNTL2_RB0, 0x01202222},
+	{REG_A6XX_RBBM_CLOCK_CNTL_CCU0, 0x00002220},
+	{REG_A6XX_RBBM_CLOCK_HYST_RB_CCU0, 0x00040f00},
+	{REG_A6XX_RBBM_CLOCK_CNTL_RAC, 0x05522022},
+	{REG_A6XX_RBBM_CLOCK_CNTL2_RAC, 0x00005555},
+	{REG_A6XX_RBBM_CLOCK_DELAY_RAC, 0x00000011},
+	{REG_A6XX_RBBM_CLOCK_HYST_RAC, 0x00445044},
+	{REG_A6XX_RBBM_CLOCK_CNTL_TSE_RAS_RBBM, 0x04222222},
+	{REG_A6XX_RBBM_CLOCK_MODE_VFD, 0x00002222},
+	{REG_A6XX_RBBM_CLOCK_MODE_GPC, 0x02222222},
+	{REG_A6XX_RBBM_CLOCK_DELAY_HLSQ_2, 0x00000002},
+	{REG_A6XX_RBBM_CLOCK_MODE_HLSQ, 0x00002222},
+	{REG_A6XX_RBBM_CLOCK_DELAY_TSE_RAS_RBBM, 0x00004000},
+	{REG_A6XX_RBBM_CLOCK_DELAY_VFD, 0x00002222},
+	{REG_A6XX_RBBM_CLOCK_DELAY_GPC, 0x00000200},
+	{REG_A6XX_RBBM_CLOCK_DELAY_HLSQ, 0x00000000},
+	{REG_A6XX_RBBM_CLOCK_HYST_TSE_RAS_RBBM, 0x00000000},
+	{REG_A6XX_RBBM_CLOCK_HYST_VFD, 0x00000000},
+	{REG_A6XX_RBBM_CLOCK_HYST_GPC, 0x04104004},
+	{REG_A6XX_RBBM_CLOCK_HYST_HLSQ, 0x00000000},
+	{REG_A6XX_RBBM_CLOCK_CNTL_UCHE, 0x22222222},
+	{REG_A6XX_RBBM_CLOCK_HYST_UCHE, 0x00000004},
+	{REG_A6XX_RBBM_CLOCK_DELAY_UCHE, 0x00000002},
+	{REG_A6XX_RBBM_ISDB_CNT, 0x00000182},
+	{REG_A6XX_RBBM_RAC_THRESHOLD_CNT, 0x00000000},
+	{REG_A6XX_RBBM_SP_HYST_CNT, 0x00000000},
+	{REG_A6XX_RBBM_CLOCK_CNTL_GMU_GX, 0x00000222},
+	{REG_A6XX_RBBM_CLOCK_DELAY_GMU_GX, 0x00000111},
+	{REG_A6XX_RBBM_CLOCK_HYST_GMU_GX, 0x00000555},
+	{},
+};
+
 /* For a615 family (a615, a616, a618 and a619) */
 const struct adreno_reglist a615_hwcg[] = {
 	{REG_A6XX_RBBM_CLOCK_CNTL_SP0,  0x02222222},
@@ -602,6 +652,8 @@ static void a6xx_set_hwcg(struct msm_gpu *gpu, bool state)
 
 	if (adreno_is_a630(adreno_gpu))
 		clock_cntl_on = 0x8aa8aa02;
+	else if (adreno_is_a610(adreno_gpu))
+		clock_cntl_on = 0xaaa8aa82;
 	else
 		clock_cntl_on = 0x8aa8aa82;
 
@@ -612,13 +664,15 @@ static void a6xx_set_hwcg(struct msm_gpu *gpu, bool state)
 		return;
 
 	/* Disable SP clock before programming HWCG registers */
-	gmu_rmw(gmu, REG_A6XX_GPU_GMU_GX_SPTPRAC_CLOCK_CONTROL, 1, 0);
+	if (!adreno_is_a610(adreno_gpu))
+		gmu_rmw(gmu, REG_A6XX_GPU_GMU_GX_SPTPRAC_CLOCK_CONTROL, 1, 0);
 
 	for (i = 0; (reg = &adreno_gpu->info->hwcg[i], reg->offset); i++)
 		gpu_write(gpu, reg->offset, state ? reg->value : 0);
 
 	/* Enable SP clock */
-	gmu_rmw(gmu, REG_A6XX_GPU_GMU_GX_SPTPRAC_CLOCK_CONTROL, 0, 1);
+	if (!adreno_is_a610(adreno_gpu))
+		gmu_rmw(gmu, REG_A6XX_GPU_GMU_GX_SPTPRAC_CLOCK_CONTROL, 0, 1);
 
 	gpu_write(gpu, REG_A6XX_RBBM_CLOCK_CNTL, state ? clock_cntl_on : 0);
 }
@@ -806,6 +860,13 @@ static void a6xx_set_ubwc_config(struct msm_gpu *gpu)
 	/* Unknown, introduced with A640/680 */
 	u32 amsbc = 0;
 
+	if (adreno_is_a610(adreno_gpu)) {
+		/* HBB = 14 */
+		hbb_lo = 1;
+		min_acc_len = 1;
+		ubwc_mode = 1;
+	}
+
 	/* a618 is using the hw default values */
 	if (adreno_is_a618(adreno_gpu))
 		return;
@@ -1073,13 +1134,13 @@ static int hw_init(struct msm_gpu *gpu)
 	a6xx_set_hwcg(gpu, true);
 
 	/* VBIF/GBIF start*/
-	if (adreno_is_a640_family(adreno_gpu) ||
+	if (adreno_is_a610(adreno_gpu) ||
+	    adreno_is_a640_family(adreno_gpu) ||
 	    adreno_is_a650_family(adreno_gpu)) {
 		gpu_write(gpu, REG_A6XX_GBIF_QSB_SIDE0, 0x00071620);
 		gpu_write(gpu, REG_A6XX_GBIF_QSB_SIDE1, 0x00071620);
 		gpu_write(gpu, REG_A6XX_GBIF_QSB_SIDE2, 0x00071620);
 		gpu_write(gpu, REG_A6XX_GBIF_QSB_SIDE3, 0x00071620);
-		gpu_write(gpu, REG_A6XX_GBIF_QSB_SIDE3, 0x00071620);
 		gpu_write(gpu, REG_A6XX_RBBM_GBIF_CLIENT_QOS_CNTL, 0x3);
 	} else {
 		gpu_write(gpu, REG_A6XX_RBBM_VBIF_CLIENT_QOS_CNTL, 0x3);
@@ -1107,18 +1168,26 @@ static int hw_init(struct msm_gpu *gpu)
 	gpu_write(gpu, REG_A6XX_UCHE_FILTER_CNTL, 0x804);
 	gpu_write(gpu, REG_A6XX_UCHE_CACHE_WAYS, 0x4);
 
-	if (adreno_is_a640_family(adreno_gpu) ||
-	    adreno_is_a650_family(adreno_gpu))
+	if (adreno_is_a640_family(adreno_gpu) || adreno_is_a650_family(adreno_gpu)) {
 		gpu_write(gpu, REG_A6XX_CP_ROQ_THRESHOLDS_2, 0x02000140);
-	else
+		gpu_write(gpu, REG_A6XX_CP_ROQ_THRESHOLDS_1, 0x8040362c);
+	} else if (adreno_is_a610(adreno_gpu)) {
+		gpu_write(gpu, REG_A6XX_CP_ROQ_THRESHOLDS_2, 0x00800060);
+		gpu_write(gpu, REG_A6XX_CP_ROQ_THRESHOLDS_1, 0x40201b16);
+	} else {
 		gpu_write(gpu, REG_A6XX_CP_ROQ_THRESHOLDS_2, 0x010000c0);
-	gpu_write(gpu, REG_A6XX_CP_ROQ_THRESHOLDS_1, 0x8040362c);
+		gpu_write(gpu, REG_A6XX_CP_ROQ_THRESHOLDS_1, 0x8040362c);
+	}
 
 	if (adreno_is_a660_family(adreno_gpu))
 		gpu_write(gpu, REG_A6XX_CP_LPAC_PROG_FIFO_SIZE, 0x00000020);
 
 	/* Setting the mem pool size */
-	gpu_write(gpu, REG_A6XX_CP_MEM_POOL_SIZE, 128);
+	if (adreno_is_a610(adreno_gpu)) {
+		gpu_write(gpu, REG_A6XX_CP_MEM_POOL_SIZE, 48);
+		gpu_write(gpu, REG_A6XX_CP_MEM_POOL_DBG_ADDR, 47);
+	} else
+		gpu_write(gpu, REG_A6XX_CP_MEM_POOL_SIZE, 128);
 
 	/* Setting the primFifo thresholds default values,
 	 * and vccCacheSkipDis=1 bit (0x200) for A640 and newer
@@ -1129,6 +1198,8 @@ static int hw_init(struct msm_gpu *gpu)
 		gpu_write(gpu, REG_A6XX_PC_DBG_ECO_CNTL, 0x00200200);
 	else if (adreno_is_a650(adreno_gpu) || adreno_is_a660(adreno_gpu))
 		gpu_write(gpu, REG_A6XX_PC_DBG_ECO_CNTL, 0x00300200);
+	else if (adreno_is_a610(adreno_gpu))
+		gpu_write(gpu, REG_A6XX_PC_DBG_ECO_CNTL, 0x00080000);
 	else
 		gpu_write(gpu, REG_A6XX_PC_DBG_ECO_CNTL, 0x00180000);
 
@@ -1144,8 +1215,10 @@ static int hw_init(struct msm_gpu *gpu)
 	a6xx_set_ubwc_config(gpu);
 
 	/* Enable fault detection */
-	gpu_write(gpu, REG_A6XX_RBBM_INTERFACE_HANG_INT_CNTL,
-		(1 << 30) | 0x1fffff);
+	if (adreno_is_a610(adreno_gpu))
+		gpu_write(gpu, REG_A6XX_RBBM_INTERFACE_HANG_INT_CNTL, (1 << 30) | 0x3ffff);
+	else
+		gpu_write(gpu, REG_A6XX_RBBM_INTERFACE_HANG_INT_CNTL, (1 << 30) | 0x1fffff);
 
 	gpu_write(gpu, REG_A6XX_UCHE_CLIENT_PF, 1);
 
@@ -1675,7 +1748,7 @@ void a6xx_bus_clear_pending_transactions(struct adreno_gpu *adreno_gpu, bool gx_
 	struct msm_gpu *gpu = &adreno_gpu->base;
 
 	if (adreno_is_a619_holi(adreno_gpu)) {
-		gpu_write(gpu, 0x18, GPR0_GBIF_HALT_REQUEST);
+		gpu_write(gpu, REG_A6XX_RBBM_GPR0_CNTL, GPR0_GBIF_HALT_REQUEST);
 		spin_until((gpu_read(gpu, REG_A6XX_RBBM_VBIF_GX_RESET_STATUS) &
 				(VBIF_RESET_ACK_MASK)) == VBIF_RESET_ACK_MASK);
 	} else if (!a6xx_has_gbif(adreno_gpu)) {
@@ -1709,6 +1782,10 @@ void a6xx_bus_clear_pending_transactions(struct adreno_gpu *adreno_gpu, bool gx_
 
 void a6xx_gpu_sw_reset(struct msm_gpu *gpu, bool assert)
 {
+	/* 11nm chips (e.g. ones with A610) have hw issues with the reset line! */
+	if (adreno_is_a610(to_adreno_gpu(gpu)))
+		return;
+
 	gpu_write(gpu, REG_A6XX_RBBM_SW_RESET_CMD, assert);
 	/* Add a barrier to avoid bad surprises */
 	mb();
drivers/gpu/drm/msm/adreno/adreno_device.c +12 -0
index b133755a56c4..2c2cdbdada4d 100644
@@ -253,6 +253,18 @@ static const struct adreno_info gpulist[] = {
 		.quirks = ADRENO_QUIRK_LMLOADKILL_DISABLE,
 		.init = a5xx_gpu_init,
 		.zapfw = "a540_zap.mdt",
+	}, {
+		.rev = ADRENO_REV(6, 1, 0, ANY_ID),
+		.revn = 610,
+		.name = "A610",
+		.fw = {
+			[ADRENO_FW_SQE] = "a630_sqe.fw",
+		},
+		.gmem = (SZ_128K + SZ_4K),
+		.inactive_period = 500,
+		.init = a6xx_gpu_init,
+		.zapfw = "a610_zap.mdt",
+		.hwcg = a612_hwcg,
 	}, {
 		.rev = ADRENO_REV(6, 1, 8, ANY_ID),
 		.revn = 618,
drivers/gpu/drm/msm/adreno/adreno_gpu.h +7 -1
index 432fee5c1516..7a5d595d4b99 100644
@@ -55,7 +55,8 @@ struct adreno_reglist {
 	u32 value;
 };
 
-extern const struct adreno_reglist a615_hwcg[], a630_hwcg[], a640_hwcg[], a650_hwcg[], a660_hwcg[];
+extern const struct adreno_reglist a612_hwcg[], a615_hwcg[], a630_hwcg[], a640_hwcg[], a650_hwcg[];
+extern const struct adreno_reglist a660_hwcg[];
 
 struct adreno_info {
 	struct adreno_rev rev;
@@ -242,6 +243,11 @@ static inline int adreno_is_a540(struct adreno_gpu *gpu)
 	return gpu->revn == 540;
 }
 
+static inline int adreno_is_a610(struct adreno_gpu *gpu)
+{
+	return gpu->revn == 610;
+}
+
 static inline int adreno_is_a618(struct adreno_gpu *gpu)
 {
 	return gpu->revn == 618;
Signature · 1 line
2.40.1
#14 lore raw

PATCH v7 14/18 drm/msm/a6xx: Fix some A619 tunables

In reply to Konrad Dybcio

Adreno 619 expects some tunables to be set differently. Make up for it.

Fixes b7616b5c69e6 ("drm/msm/adreno: Add A619 support")
---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +5 -1
index ca055bff23c8..9f296928c249 100644
@@ -1198,6 +1198,8 @@ static int hw_init(struct msm_gpu *gpu)
 		gpu_write(gpu, REG_A6XX_PC_DBG_ECO_CNTL, 0x00200200);
 	else if (adreno_is_a650(adreno_gpu) || adreno_is_a660(adreno_gpu))
 		gpu_write(gpu, REG_A6XX_PC_DBG_ECO_CNTL, 0x00300200);
+	else if (adreno_is_a619(adreno_gpu))
+		gpu_write(gpu, REG_A6XX_PC_DBG_ECO_CNTL, 0x00018000);
 	else if (adreno_is_a610(adreno_gpu))
 		gpu_write(gpu, REG_A6XX_PC_DBG_ECO_CNTL, 0x00080000);
 	else
@@ -1215,7 +1217,9 @@ static int hw_init(struct msm_gpu *gpu)
 	a6xx_set_ubwc_config(gpu);
 
 	/* Enable fault detection */
-	if (adreno_is_a610(adreno_gpu))
+	if (adreno_is_a619(adreno_gpu))
+		gpu_write(gpu, REG_A6XX_RBBM_INTERFACE_HANG_INT_CNTL, (1 << 30) | 0x3fffff);
+	else if (adreno_is_a610(adreno_gpu))
 		gpu_write(gpu, REG_A6XX_RBBM_INTERFACE_HANG_INT_CNTL, (1 << 30) | 0x3ffff);
 	else
 		gpu_write(gpu, REG_A6XX_RBBM_INTERFACE_HANG_INT_CNTL, (1 << 30) | 0x1fffff);
Signature · 1 line
2.40.1
#15 lore raw

PATCH v7 15/18 drm/msm/a6xx: Use "else if" in GPU speedbin rev matching

In reply to Konrad Dybcio

The GPU can only be one at a time. Turn a series of ifs into if + elseifs to save some CPU cycles.

---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +4 -4
index 9f296928c249..99bb3d16657a 100644
@@ -2174,16 +2174,16 @@ static u32 fuse_to_supp_hw(struct device *dev, struct adreno_rev rev, u32 fuse)
 	if (adreno_cmp_rev(ADRENO_REV(6, 1, 8, ANY_ID), rev))
 		val = a618_get_speed_bin(fuse);
 
-	if (adreno_cmp_rev(ADRENO_REV(6, 1, 9, ANY_ID), rev))
+	else if (adreno_cmp_rev(ADRENO_REV(6, 1, 9, ANY_ID), rev))
 		val = a619_get_speed_bin(fuse);
 
-	if (adreno_cmp_rev(ADRENO_REV(6, 3, 5, ANY_ID), rev))
+	else if (adreno_cmp_rev(ADRENO_REV(6, 3, 5, ANY_ID), rev))
 		val = adreno_7c3_get_speed_bin(fuse);
 
-	if (adreno_cmp_rev(ADRENO_REV(6, 4, 0, ANY_ID), rev))
+	else if (adreno_cmp_rev(ADRENO_REV(6, 4, 0, ANY_ID), rev))
 		val = a640_get_speed_bin(fuse);
 
-	if (adreno_cmp_rev(ADRENO_REV(6, 5, 0, ANY_ID), rev))
+	else if (adreno_cmp_rev(ADRENO_REV(6, 5, 0, ANY_ID), rev))
 		val = a650_get_speed_bin(fuse);
 
 	if (val == UINT_MAX) {
Signature · 1 line
2.40.1
#16 lore raw

PATCH v7 16/18 drm/msm/a6xx: Use adreno_is_aXYZ macros in speedbin matching

In reply to Konrad Dybcio

Before transitioning to using per-SoC and not per-Adreno speedbin fuse values (need another patchset to land elsewhere), a good improvement/stopgap solution is to use adreno_is_aXYZ macros in place of explicit revision matching. Do so to allow differentiating between A619 and A619_holi.

---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c   | 18 +++++++++---------
 drivers/gpu/drm/msm/adreno/adreno_gpu.h | 14 ++++++++++++--
 2 files changed, 21 insertions(+), 11 deletions(-)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +9 -9
index 99bb3d16657a..5ad19978390c 100644
@@ -2167,23 +2167,23 @@ static u32 adreno_7c3_get_speed_bin(u32 fuse)
 	return UINT_MAX;
 }
 
-static u32 fuse_to_supp_hw(struct device *dev, struct adreno_rev rev, u32 fuse)
+static u32 fuse_to_supp_hw(struct device *dev, struct adreno_gpu *adreno_gpu, u32 fuse)
 {
 	u32 val = UINT_MAX;
 
-	if (adreno_cmp_rev(ADRENO_REV(6, 1, 8, ANY_ID), rev))
+	if (adreno_is_a618(adreno_gpu))
 		val = a618_get_speed_bin(fuse);
 
-	else if (adreno_cmp_rev(ADRENO_REV(6, 1, 9, ANY_ID), rev))
+	else if (adreno_is_a619(adreno_gpu))
 		val = a619_get_speed_bin(fuse);
 
-	else if (adreno_cmp_rev(ADRENO_REV(6, 3, 5, ANY_ID), rev))
+	else if (adreno_is_7c3(adreno_gpu))
 		val = adreno_7c3_get_speed_bin(fuse);
 
-	else if (adreno_cmp_rev(ADRENO_REV(6, 4, 0, ANY_ID), rev))
+	else if (adreno_is_a640(adreno_gpu))
 		val = a640_get_speed_bin(fuse);
 
-	else if (adreno_cmp_rev(ADRENO_REV(6, 5, 0, ANY_ID), rev))
+	else if (adreno_is_a650(adreno_gpu))
 		val = a650_get_speed_bin(fuse);
 
 	if (val == UINT_MAX) {
@@ -2196,7 +2196,7 @@ static u32 fuse_to_supp_hw(struct device *dev, struct adreno_rev rev, u32 fuse)
 	return (1 << val);
 }
 
-static int a6xx_set_supported_hw(struct device *dev, struct adreno_rev rev)
+static int a6xx_set_supported_hw(struct device *dev, struct adreno_gpu *adreno_gpu)
 {
 	u32 supp_hw;
 	u32 speedbin;
@@ -2215,7 +2215,7 @@ static int a6xx_set_supported_hw(struct device *dev, struct adreno_rev rev)
 		return ret;
 	}
 
-	supp_hw = fuse_to_supp_hw(dev, rev, speedbin);
+	supp_hw = fuse_to_supp_hw(dev, adreno_gpu, speedbin);
 
 	ret = devm_pm_opp_set_supported_hw(dev, &supp_hw, 1);
 	if (ret)
@@ -2334,7 +2334,7 @@ struct msm_gpu *a6xx_gpu_init(struct drm_device *dev)
 
 	a6xx_llc_slices_init(pdev, a6xx_gpu);
 
-	ret = a6xx_set_supported_hw(&pdev->dev, config->rev);
+	ret = a6xx_set_supported_hw(&pdev->dev, adreno_gpu);
 	if (ret) {
 		a6xx_destroy(&(a6xx_gpu->base.base));
 		return ERR_PTR(ret);
drivers/gpu/drm/msm/adreno/adreno_gpu.h +12 -2
index 7a5d595d4b99..21513cec038f 100644
@@ -268,9 +268,9 @@ static inline int adreno_is_a630(struct adreno_gpu *gpu)
 	return gpu->revn == 630;
 }
 
-static inline int adreno_is_a640_family(struct adreno_gpu *gpu)
+static inline int adreno_is_a640(struct adreno_gpu *gpu)
 {
-	return (gpu->revn == 640) || (gpu->revn == 680);
+	return gpu->revn == 640;
 }
 
 static inline int adreno_is_a650(struct adreno_gpu *gpu)
@@ -289,6 +289,11 @@ static inline int adreno_is_a660(struct adreno_gpu *gpu)
 	return gpu->revn == 660;
 }
 
+static inline int adreno_is_a680(struct adreno_gpu *gpu)
+{
+	return gpu->revn == 680;
+}
+
 /* check for a615, a616, a618, a619 or any derivatives */
 static inline int adreno_is_a615_family(struct adreno_gpu *gpu)
 {
@@ -306,6 +311,11 @@ static inline int adreno_is_a650_family(struct adreno_gpu *gpu)
 	return gpu->revn == 650 || gpu->revn == 620 || adreno_is_a660_family(gpu);
 }
 
+static inline int adreno_is_a640_family(struct adreno_gpu *gpu)
+{
+	return adreno_is_a640(gpu) || adreno_is_a680(gpu);
+}
+
 u64 adreno_private_address_space_size(struct msm_gpu *gpu);
 int adreno_get_param(struct msm_gpu *gpu, struct msm_file_private *ctx,
 		     uint32_t param, uint64_t *value, uint32_t *len);
Signature · 1 line
2.40.1
#17 lore raw

PATCH v7 17/18 drm/msm/a6xx: Add A619_holi speedbin support

In reply to Konrad Dybcio

A619_holi is implemented on at least two SoCs: SM4350 (holi) and SM6375 (blair). This is what seems to be a first occurrence of this happening, but it's easy to overcome by guarding the SoC-specific fuse values with of_machine_is_compatible(). Do just that to enable frequency limiting on these SoCs.

---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +31 -0
index 5ad19978390c..c07b25fc2bd9 100644
@@ -2114,6 +2114,34 @@ static u32 a618_get_speed_bin(u32 fuse)
 	return UINT_MAX;
 }
 
+static u32 a619_holi_get_speed_bin(u32 fuse)
+{
+	/*
+	 * There are (at least) two SoCs implementing A619_holi: SM4350 (holi)
+	 * and SM6375 (blair). Limit the fuse matching to the corresponding
+	 * SoC to prevent bogus frequency setting (as improbable as it may be,
+	 * given unexpected fuse values are.. unexpected! But still possible.)
+	 */
+
+	if (fuse == 0)
+		return 0;
+
+	if (of_machine_is_compatible("qcom,sm4350")) {
+		if (fuse == 138)
+			return 1;
+		else if (fuse == 92)
+			return 2;
+	} else if (of_machine_is_compatible("qcom,sm6375")) {
+		if (fuse == 190)
+			return 1;
+		else if (fuse == 177)
+			return 2;
+	} else
+		pr_warn("Unknown SoC implementing A619_holi!\n");
+
+	return UINT_MAX;
+}
+
 static u32 a619_get_speed_bin(u32 fuse)
 {
 	if (fuse == 0)
@@ -2174,6 +2202,9 @@ static u32 fuse_to_supp_hw(struct device *dev, struct adreno_gpu *adreno_gpu, u3
 	if (adreno_is_a618(adreno_gpu))
 		val = a618_get_speed_bin(fuse);
 
+	else if (adreno_is_a619_holi(adreno_gpu))
+		val = a619_holi_get_speed_bin(fuse);
+
 	else if (adreno_is_a619(adreno_gpu))
 		val = a619_get_speed_bin(fuse);
 
Signature · 1 line
2.40.1
#18 lore raw

PATCH v7 18/18 drm/msm/a6xx: Add A610 speedbin support

In reply to Konrad Dybcio

A610 is implemented on at least three SoCs: SM6115 (bengal), SM6125 (trinket) and SM6225 (khaje). Trinket does not support speed binning (only a single SKU exists) and we don't yet support khaje upstream. Hence, add a fuse mapping table for bengal to allow for per-chip frequency limiting.

---
 drivers/gpu/drm/msm/adreno/a6xx_gpu.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
drivers/gpu/drm/msm/adreno/a6xx_gpu.c +27 -0
index c07b25fc2bd9..d004458ca783 100644
@@ -2102,6 +2102,30 @@ static bool a6xx_progress(struct msm_gpu *gpu, struct msm_ringbuffer *ring)
 	return progress;
 }
 
+static u32 a610_get_speed_bin(u32 fuse)
+{
+	/*
+	 * There are (at least) three SoCs implementing A610: SM6125 (trinket),
+	 * SM6115 (bengal) and SM6225 (khaje). Trinket does not have speedbinning,
+	 * as only a single SKU exists and we don't support khaje upstream yet.
+	 * Hence, this matching table is only valid for bengal and can be easily
+	 * expanded if need be.
+	 */
+
+	if (fuse == 0)
+		return 0;
+	else if (fuse == 206)
+		return 1;
+	else if (fuse == 200)
+		return 2;
+	else if (fuse == 157)
+		return 3;
+	else if (fuse == 127)
+		return 4;
+
+	return UINT_MAX;
+}
+
 static u32 a618_get_speed_bin(u32 fuse)
 {
 	if (fuse == 0)
@@ -2199,6 +2223,9 @@ static u32 fuse_to_supp_hw(struct device *dev, struct adreno_gpu *adreno_gpu, u3
 {
 	u32 val = UINT_MAX;
 
+	if (adreno_is_a610(adreno_gpu))
+		val = a610_get_speed_bin(fuse);
+
 	if (adreno_is_a618(adreno_gpu))
 		val = a618_get_speed_bin(fuse);
 
Signature · 1 line
2.40.1