Add Ethernet driver for StarFive JH7110 SoC
Subsystems (7)
v9 cover Add Ethernet driver for StarFive JH7110 SoC
This series adds ethernet support for the StarFive JH7110 RISC-V SoC, which includes a dwmac-5.20 MAC driver (from Synopsys DesignWare). This series has been tested and works fine on VisionFive-2 v1.2A and v1.3B SBC boards.
For more information and support, you can visit RVspace wiki[1]. You can simply review or test the patches at the link [2]. This patchset should be applied after the patchset [3] [4].
[1]: https://wiki.rvspace.org/
[2]: https://github.com/saminGuo/linux/tree/vf2-6.3rc3-gmac-net-next
[3]: https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]
[4]: https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]
Changes since v8:
Patch 4:
- Dropped irrelevant MAINTAINERS context (by Jakub Kicinski)
Patch 6:
- Moved error messages to starfive_dwmac_set_mode function to avoid getting error messages twice when syscon_regmap_lookup_by_phandle_args fails. (by Emil)
- Renamed patch header to "net: stmmac: dwmac-starfive:xxx" (by Emil)
hanges history:
Changes since v7:
Patch 4:
- Constrained the reg/interrupts/interrupt-names properties (by Krzysztof Kozlowski)
Changes since v6:
- Sended network patches[patch 1,2,3,4,5,6] and riscv trees patches[patch 7,8] separately (by Jakub Kicinski)
Changes since v5:
- Dropped "depends on STMMAC_ETH" and compiled DWMAC_STARFIVE to m by default (by Emil)
- Removed clk_gtx in struct starfive_dwmac due to this pointer is only set, but never read. (by Emil)
- Only setting the plat_dat->fix_mac_speed callback when it is needed (by Emil)
- Moved mdio/phy nodes from SOC .dtsi into board .dtsi (by Andrew)
- Modified the parameters passed by starfive,syscon (by Andrew && Emil)
<syscon, offset, mask> ==> <syscon, offset, shift>
- Optimized the patchs(Fewer patches from 12 to 8)
1)merged patch-7 into patch-4 (by Rob)
2)merged patch-9 into patch-5
2)merged patch-11,12 into patch-10
3)Adjusted the patchs order
- Fixed the unevaluatedProperties property from true to false (by Rob)
- Replaced contains:enum with items:const for reset-names in snps,dwmac.yaml (by Rob)
- Tested-by: Tommaso Merciai <[email protected]>
Changes since v4:
- Supported both visionfive 2 v1.2A and visionfive 2 v1.3B.
- Reworded the maxitems number of resets property in 'snps,dwmac.yaml'.
- Suggested by Emil, dropped the _PLAT/_plat from the config/function/struct/file names.
- Suggested by Emil, added MODULE_DEVICE_TABLE().
- Suggested by Emil, dropped clk_gtxclk and use clk_tx_inv to set the clock frequency.
- Added phy interface mode configuration function.
- Rebased on tag v6.2.
Changes since v3:
- Reworded the maxitems number of resets property in 'snps,dwmac.yaml'
- Removed the unused code in 'dwmac-starfive-plat.c'.
- Reworded the return statement in 'starfive_eth_plat_fix_mac_speed' function.
Changes since v2:
- Renamed the dt-bindings 'starfive,jh71x0-dwmac.yaml' to 'starfive,jh7110-dwmac.yaml'.
- Reworded the commit messages.
- Reworded the example context in the dt-binding 'starfive,jh7110-dwmac.yaml'.
- Removed "starfive,jh7100-dwmac" compatible string and special initialization of jh7100.
- Removed the parts of YT8531,so dropped patch 5 and 6.
- Reworded the maxitems number of resets property in 'snps,dwmac.yaml'.
Changes since v1:
- Recovered the author of the 1st and 3rd patches back to Emil Renner Berthing.
- Added a new patch to update maxitems number of resets property in 'snps,dwmac.yaml'.
- Fixed the check errors reported by "make dt_binding_check".
- Renamed the dt-binding 'starfive,dwmac-plat.yaml' to 'starfive,jh71x0-dwmac.yaml'.
- Updated the example context in the dt-binding 'starfive,jh71x0-dwmac.yaml'.
- Added new dt-binding 'motorcomm,yt8531.yaml' to describe details of phy clock delay configuration parameters.
- Added more comments for PHY driver setting. For more details, see 'motorcomm,yt8531.yaml'.
- Moved mdio device tree node from 'jh7110-starfive-visionfive-v2.dts' to 'jh7110.dtsi'.
- Re-worded the commit message of several patches.
- Renamed all the functions with starfive_eth_plat prefix in 'dwmac-starfive-plat.c'.
- Added "starfive,jh7100-dwmac" compatible string and special init to support JH7100.
Previous versions:
v1 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
v2 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
v3 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
v4 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
v5 - https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/
v6 - https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/
v7 - https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/
v8 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
Emil Renner Berthing (2):
dt-bindings: net: snps,dwmac: Add dwmac-5.20 version
net: stmmac: platform: Add snps,dwmac-5.20 IP compatible string
Samin Guo (3):
dt-bindings: net: snps,dwmac: Add 'ahb' reset/reset-name
net: stmmac: Add glue layer for StarFive JH7110 SoC
net: stmmac: starfive-dmac: Add phy interface settings
Yanhong Wang (1):
dt-bindings: net: Add support StarFive dwmac
.../devicetree/bindings/net/snps,dwmac.yaml | 17 +- .../bindings/net/starfive,jh7110-dwmac.yaml | 144 +++++++++++++++ MAINTAINERS | 7 + drivers/net/ethernet/stmicro/stmmac/Kconfig | 12 ++ drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + .../ethernet/stmicro/stmmac/dwmac-starfive.c | 169 ++++++++++++++++++ .../ethernet/stmicro/stmmac/stmmac_platform.c | 3 +- 7 files changed, 348 insertions(+), 5 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c
base-commit: e8d018dd0257f744ca50a729e3d042cf2ec9da65
prerequisite-patch-id: 8a6f135bcabdad4a4bfb21f0c6a0ffd2bb57efe7
prerequisite-patch-id: 1da7255d6aeb5576ca810116a9323452be2202fa
prerequisite-patch-id: 50d53a21f91f4087fc80b6f1f72864adfb0002b9
prerequisite-patch-id: 0df3703af91c30f1ca2c47f5609012f2d7200028
prerequisite-patch-id: 89f049f951e5acf75aab92541992f816fd0acc0d
prerequisite-patch-id: 85c5bb437c383b2e68c79e59a439f01b7bcd963e
prerequisite-patch-id: 8600b156a235be2b3db53be3f834e7a370e2cfb9
prerequisite-patch-id: 1b2d0982b18da060c82134f05bf3ce16425bac8d
prerequisite-patch-id: 090ba4b78d47bc19204916e76fdbc70021785388
prerequisite-patch-id: a5d9e0f7d4f8163f566678894cf693015119f2d9
prerequisite-patch-id: 42d352fe14713b74951c4513128a0a494b2dce76
prerequisite-patch-id: bb939c0c7c26b08addfccd890f9d3974b6eaec53
prerequisite-patch-id: 4f10a3d827679eafbd3d49d2e21f31032dc9c418
prerequisite-patch-id: fd93763b95469912bde9bdfa4cd827c8d5dba9c6
prerequisite-patch-id: 6987950c2eb4b3773b2df8f7934eff434244aeab
prerequisite-patch-id: 258ea5f9b8bf41b6981345dcc81795f25865d38f
prerequisite-patch-id: 8b6f2c9660c0ac0ee4e73e4c21aca8e6b75e81b9
prerequisite-patch-id: dbb0c0151b8bdf093e6ce79fd2fe3f60791a6e0b
prerequisite-patch-id: e7773c977a7b37692e9792b21cc4f17fa58f9215
prerequisite-patch-id: d57e95d31686772abc4c4d5aa1cadc344dc293cd
prerequisite-patch-id: 9f911969d0a550648493952c99096d26e05d4d83
prerequisite-patch-id: 999c243dca89d56d452aa52ea3e181358b5c1d80
prerequisite-patch-id: 1be0fb49e0fbe293ca8fa94601e191b13c8c67d9 --
2.17.1
_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv
PATCH v9 1/6 dt-bindings: net: snps,dwmac: Add dwmac-5.20 version
From: Emil Renner Berthing <[email protected]>
Add dwmac-5.20 IP version to snps.dwmac.yaml
--- Documentation/devicetree/bindings/net/snps,dwmac.yaml | 4 ++++ 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/net/snps,dwmac.yaml +4 -0
@@ -30,6 +30,7 @@ select: - snps,dwmac-4.10a - snps,dwmac-4.20a - snps,dwmac-5.10a + - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10
@@ -87,6 +88,7 @@ properties: - snps,dwmac-4.10a - snps,dwmac-4.20a - snps,dwmac-5.10a + - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10
@@ -575,6 +577,7 @@ allOf: - snps,dwmac-3.50a - snps,dwmac-4.10a - snps,dwmac-4.20a + - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10 - st,spear600-gmac
@@ -629,6 +632,7 @@ allOf: - snps,dwmac-4.10a - snps,dwmac-4.20a - snps,dwmac-5.10a + - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10 - st,spear600-gmac
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
PATCH v9 2/6 net: stmmac: platform: Add snps,dwmac-5.20 IP compatible string
In reply to Samin GuoFrom: Emil Renner Berthing <[email protected]>
Add "snps,dwmac-5.20" compatible string for 5.20 version that can avoid to define some platform data in the glue layer.
--- drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +2 -1
@@ -519,7 +519,8 @@ stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac)if (of_device_is_compatible (np,"snps,dwmac-4.00" ) ||of_device_is_compatible (np,"snps,dwmac-4.10a" ) ||of_device_is_compatible (np,"snps,dwmac-4.20a" ) || -of_device_is_compatible (np,"snps,dwmac-5.10a" )) { +of_device_is_compatible (np,"snps,dwmac-5.10a" ) || +of_device_is_compatible (np,"snps,dwmac-5.20" )) { plat->has_gmac4 =1 ; plat->has_gmac =0 ; plat->pmt =1 ;
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
PATCH v9 3/6 dt-bindings: net: snps,dwmac: Add 'ahb' reset/reset-name
In reply to Samin GuoAccording to:stmmac_platform.c: stmmac_probe_config_dtstmmac_main.c: stmmac_dvr_probe
dwmac controller may require one (stmmaceth) or two (stmmaceth+ahb) reset signals, and the maxItems of resets/reset-names is going to be 2.
The gmac of Starfive Jh7110 SOC must have two resets. it uses snps,dwmac-5.20 IP.
--- .../devicetree/bindings/net/snps,dwmac.yaml | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-)
Documentation/devicetree/bindings/net/snps,dwmac.yaml +8 -4
@@ -133,12 +133,16 @@ properties: - ptp_ref resets: - maxItems: 1 - description: - MAC Reset signal. + minItems: 1 + items: + - description: GMAC stmmaceth reset + - description: AHB reset reset-names: - const: stmmaceth + minItems: 1 + items: + - const: stmmaceth + - const: ahb power-domains: maxItems: 1
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
PATCH v9 4/6 dt-bindings: net: Add support StarFive dwmac
In reply to Samin GuoFrom: Yanhong Wang <[email protected]>
Add documentation to describe StarFive dwmac driver(GMAC).
--- .../devicetree/bindings/net/snps,dwmac.yaml | 1 + .../bindings/net/starfive,jh7110-dwmac.yaml | 144 ++++++++++++++++++ MAINTAINERS | 6 + 3 files changed, 151 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml
Documentation/devicetree/bindings/net/snps,dwmac.yaml +1 -0
@@ -91,6 +91,7 @@ properties: - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10 + - starfive,jh7110-dwmac reg: minItems: 1
Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml new file +144 -0
144 lines not on this page · raw message
MAINTAINERS +6 -0
@@ -19905,6 +19905,12 @@ M: Emil Renner Berthing <[email protected]> S: Maintained F: arch/riscv/boot/dts/starfive/ +STARFIVE DWMAC GLUE LAYER +M: Emil Renner Berthing <[email protected]> +M: Samin Guo <[email protected]> +S: Maintained +F: Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml + STARFIVE JH7100 CLOCK DRIVERS M: Emil Renner Berthing <[email protected]> S: Maintained
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Re: [net-next v9 4/6] dt-bindings: net: Add support StarFive dwmac
Quoted 118 lines · Samin Guo
From: Yanhong Wang <[email protected]>
Add documentation to describe StarFive dwmac driver(GMAC).
Signed-off-by Yanhong Wang <[email protected]>Signed-off-by Samin Guo <[email protected]>--- .../devicetree/bindings/net/snps,dwmac.yaml | 1 + .../bindings/net/starfive,jh7110-dwmac.yaml | 144 ++++++++++++++++++ MAINTAINERS | 6 + 3 files changed, 151 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yamlDocumentation/devicetree/bindings/net/snps,dwmac.yaml +1
-0@@ -91,6 +91,7 @@ properties: - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10 + - starfive,jh7110-dwmac reg: minItems: 1Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml new file +87
-0@@ -0,0 +1,144 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2022 StarFive Technology Co., Ltd. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/starfive,jh7110-dwmac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: StarFive JH7110 DWMAC glue layer + +maintainers: + - Emil Renner Berthing <[email protected]> + - Samin Guo <[email protected]> + +select: + properties: + compatible: + contains: + enum: + - starfive,jh7110-dwmac + required: + - compatible + +properties: + compatible: + items: + - enum: + - starfive,jh7110-dwmac + - const: snps,dwmac-5.20 + + reg: + maxItems: 1 + + clocks: + items: + - description: GMAC main clock + - description: GMAC AHB clock + - description: PTP clock + - description: TX clock + - description: GTX clock + + clock-names: + items: + - const: stmmaceth + - const: pclk + - const: ptp_ref + - const: tx + - const: gtx + + interrupts: + minItems: 3 + maxItems: 3 + + interrupt-names: + minItems: 3 + maxItems: 3 + + resets: + items: + - description: MAC Reset signal. + - description: AHB Reset signal. + + reset-names: + items: + - const: stmmaceth + - const: ahb + + starfive,tx-use-rgmii-clk: + description: + Tx clock is provided by external rgmii clock. + type: boolean + + starfive,syscon: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to syscon that configures phy mode + - description: Offset of phy mode selection + - description: Shift of phy mode selection + description: + A phandle to syscon with two arguments that configure phy mode. + The argument one is the offset of phy mode selection, the + argument two is the shift of phy mode selection. + +allOf: + - $ref: snps,dwmac.yaml# + +unevaluatedProperties: false
Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml line 97
Quoted 10 lines
Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml new file +10
-0+ +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + - interrupt-names + - resets + - reset-names
This is a friendly reminder during the review process.
It seems my previous comments were not fully addressed. Maybe my feedback got lost between the quotes, maybe you just forgot to apply it. Please go back to the previous discussion and either implement all requested changes or keep discussing them.
Thank you.
Best regards,
Krzysztof
Re: [net-next v9 4/6] dt-bindings: net: Add support StarFive dwmac
Re: [net-next v9 4/6] dt-bindings: net: Add support StarFive dwmac
From: Krzysztof Kozlowski <[email protected]>
to: Samin Guo <[email protected]>, [email protected], [email protected], [email protected], [email protected]
data: 2023/4/5
Quoted 137 lines · Samin Guo
Quoted 118 lines
From: Yanhong Wang <[email protected]>
Add documentation to describe StarFive dwmac driver(GMAC).
Signed-off-by Yanhong Wang <[email protected]>Signed-off-by Samin Guo <[email protected]>--- .../devicetree/bindings/net/snps,dwmac.yaml | 1 + .../bindings/net/starfive,jh7110-dwmac.yaml | 144 ++++++++++++++++++ MAINTAINERS | 6 + 3 files changed, 151 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yamlDocumentation/devicetree/bindings/net/snps,dwmac.yaml +1
-0@@ -91,6 +91,7 @@ properties: - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10 + - starfive,jh7110-dwmac reg: minItems: 1Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml new file +87
-0@@ -0,0 +1,144 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2022 StarFive Technology Co., Ltd. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/starfive,jh7110-dwmac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: StarFive JH7110 DWMAC glue layer + +maintainers: + - Emil Renner Berthing <[email protected]> + - Samin Guo <[email protected]> + +select: + properties: + compatible: + contains: + enum: + - starfive,jh7110-dwmac + required: + - compatible + +properties: + compatible: + items: + - enum: + - starfive,jh7110-dwmac + - const: snps,dwmac-5.20 + + reg: + maxItems: 1 + + clocks: + items: + - description: GMAC main clock + - description: GMAC AHB clock + - description: PTP clock + - description: TX clock + - description: GTX clock + + clock-names: + items: + - const: stmmaceth + - const: pclk + - const: ptp_ref + - const: tx + - const: gtx + + interrupts: + minItems: 3 + maxItems: 3 + + interrupt-names: + minItems: 3 + maxItems: 3 + + resets: + items: + - description: MAC Reset signal. + - description: AHB Reset signal. + + reset-names: + items: + - const: stmmaceth + - const: ahb + + starfive,tx-use-rgmii-clk: + description: + Tx clock is provided by external rgmii clock. + type: boolean + + starfive,syscon: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to syscon that configures phy mode + - description: Offset of phy mode selection + - description: Shift of phy mode selection + description: + A phandle to syscon with two arguments that configure phy mode. + The argument one is the offset of phy mode selection, the + argument two is the shift of phy mode selection. + +allOf: + - $ref: snps,dwmac.yaml# + +unevaluatedProperties: falseDocumentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml line 97
Quoted 10 lines
Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml new file +10
-0+ +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + - interrupt-names + - resets + - reset-namesThis is a friendly reminder during the review process.
It seems my previous comments were not fully addressed. Maybe my feedback got lost between the quotes, maybe you just forgot to apply it. Please go back to the previous discussion and either implement all requested changes or keep discussing them.
Quoted 6 lines
Thank you.
Best regards,
Krzysztof
Hi Krzysztof,
Sorry about that I missed this:
required: goes after properties
I'll fix it :)
Best regards,
Samin
PATCH v9 5/6 net: stmmac: Add glue layer for StarFive JH7110 SoC
In reply to Samin GuoThis adds StarFive dwmac driver support on the StarFive JH7110 SoC.
--- MAINTAINERS | 1 + drivers/net/ethernet/stmicro/stmmac/Kconfig | 12 ++ drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + .../ethernet/stmicro/stmmac/dwmac-starfive.c | 121 ++++++++++++++++++ 4 files changed, 135 insertions(+) create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c
MAINTAINERS +1 -0
@@ -19909,6 +19909,7 @@ STARFIVE DWMAC GLUE LAYER M: Emil Renner Berthing <[email protected]> M: Samin Guo <[email protected]> S: Maintained +F: Documentation/devicetree/bindings/net/dwmac-starfive.c F: Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml STARFIVE JH7100 CLOCK DRIVERS
drivers/net/ethernet/stmicro/stmmac/Kconfig +12 -0
@@ -165,6 +165,18 @@ config DWMAC_SOCFPGA for the stmmac device driver. This driver is used for arria5 and cyclone5 FPGA SoCs. +config DWMAC_STARFIVE + tristate "StarFive dwmac support" + depends on OF && (ARCH_STARFIVE || COMPILE_TEST) + select MFD_SYSCON + default m if ARCH_STARFIVE + help + Support for ethernet controllers on StarFive RISC-V SoCs + + This selects the StarFive platform specific glue layer support for + the stmmac device driver. This driver is used for StarFive JH7110 + ethernet controller. + config DWMAC_STI tristate "STi GMAC support" default ARCH_STI
drivers/net/ethernet/stmicro/stmmac/Makefile +1 -0
@@ -23,6 +23,7 @@ obj-$(CONFIG_DWMAC_OXNAS) += dwmac-oxnas.o obj-$(CONFIG_DWMAC_QCOM_ETHQOS) += dwmac-qcom-ethqos.o obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o +obj-$(CONFIG_DWMAC_STARFIVE) += dwmac-starfive.o obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o obj-$(CONFIG_DWMAC_STM32) += dwmac-stm32.o obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c new file +121 -0
121 lines not on this page · raw message
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Jakub Kicinski
maintainerRe: [net-next v9 5/6] net: stmmac: Add glue layer for StarFive JH7110 SoC
Quoted 6 lines · On Tue, 28 Mar 2023 14:20:08 +0800 Samin Guo wrote:
This adds StarFive dwmac driver support on the StarFive JH7110 SoC.
Tested-by Tommaso Merciai <[email protected]>Co-developed-by Emil Renner Berthing <[email protected]>Signed-off-by Emil Renner Berthing <[email protected]>Signed-off-by Samin Guo <[email protected]>
Excellent, now it applies cleanly :)
Our clang build with W=1 complains that:
drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c:37:2: warning: variable 'rate' is used uninitialized whenever switch default is taken [-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c:42:36: note: uninitialized use occurs here
err = clk_set_rate(dwmac->clk_tx, rate);
^~~~
drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c:24:20: note: initialize the variable 'rate' to silence this warning
unsigned long rate;
^
= 0not sure how you prefer to fix this. Maybe return early?
Re: [net-next v9 5/6] net: stmmac: Add glue layer for StarFive JH7110 SoC
Re: [net-next v9 5/6] net: stmmac: Add glue layer for StarFive JH7110 SoC
From: Jakub Kicinski <[email protected]>
to: Samin Guo <[email protected]>
data: 2023/3/29
Quoted 24 lines · On Tue, 28 Mar 2023 14:20:08 +0800 Samin Guo wrote:
Quoted 6 lines
This adds StarFive dwmac driver support on the StarFive JH7110 SoC.
Tested-by Tommaso Merciai <[email protected]>Co-developed-by Emil Renner Berthing <[email protected]>Signed-off-by Emil Renner Berthing <[email protected]>Signed-off-by Samin Guo <[email protected]>Excellent, now it applies cleanly :)
Our clang build with W=1 complains that:
drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c:37:2: warning: variable 'rate' is used uninitialized whenever switch default is taken [-Wsometimes-uninitialized]default: ^~~~~~~ drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c:42:36: note: uninitialized use occurs here err = clk_set_rate(dwmac->clk_tx, rate); ^~~~ drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c:24:20: note: initialize the variable 'rate' to silence this warning unsigned long rate; ^ = 0
Quoted 1 line
not sure how you prefer to fix this. Maybe return early?
Hi Jakub,
Sorry, gcc I used does not report this error (:, and clang compile checks are more stringent.
Also, if return early at default node, Arun Ramadoss doesn't think it's a good idea because the function is a void type.
I think I can initialize the value of rate first by clk_get_rate (Intel did the same <dwmac-intel-plat.c: kmb_eth_fix_mac_speed >), like this:
static void starfive_dwmac_fix_mac_speed(void *priv, unsigned int speed)
{
struct starfive_dwmac *dwmac = priv;
unsigned long rate;
int err;
rate = clk_get_rate(dwmac->tx_clk);
switch (speed) {
case SPEED_1000:
rate = 125000000;
break;
case SPEED_100:
rate = 25000000;
break;
case SPEED_10:
rate = 2500000;
break;
default:
dev_err(dwmac->dev, "invalid speed %u\n", speed);
break;
}
err = clk_set_rate(dwmac->clk_tx, rate);
if (err)
dev_err(dwmac->dev, "failed to set tx rate %lu\n", rate);
}What do you think?
Best regards,
Samin
Jakub Kicinski
maintainerRe: [net-next v9 5/6] net: stmmac: Add glue layer for StarFive JH7110 SoC
Quoted 28 lines · On Wed, 29 Mar 2023 10:57:00 +0800 Guo Samin wrote:
static void
starfive_dwmac_fix_mac_speed(void *priv, unsigned int speed){ struct starfive_dwmac *dwmac = priv; unsigned long rate; int err; rate = clk_get_rate(dwmac->tx_clk); switch (speed) { case SPEED_1000: rate = 125000000; break; case SPEED_100: rate = 25000000; break; case SPEED_10: rate = 2500000; break; default: dev_err(dwmac->dev, "invalid speed %u\n", speed); break; } err = clk_set_rate(dwmac->clk_tx, rate); if (err) dev_err(dwmac->dev, "failed to set tx rate %lu\n", rate); }
Quoted 1 line
What do you think?
Yup, that's even better.
PATCH v9 6/6 net: stmmac: starfive-dmac: Add phy interface settings
In reply to Samin Guodwmac supports multiple modess. When working under rmii and rgmii, you need to set different phy interfaces.
According to the dwmac document, when working in rmii, it needs to be set to 0x4, and rgmii needs to be set to 0x1.
The phy interface needs to be set in syscon, the format is as follows:
starfive,syscon: <&syscon, offset, shift>
--- .../ethernet/stmicro/stmmac/dwmac-starfive.c | 48 +++++++++++++++++++ 1 file changed, 48 insertions(+)
drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c +48 -0
@@ -13,6 +13,10 @@#include "stmmac_platform.h" +#define STARFIVE_DWMAC_PHY_INFT_RGMII 0x1 +#define STARFIVE_DWMAC_PHY_INFT_RMII 0x4 +#define STARFIVE_DWMAC_PHY_INFT_FIELD 0x7U +struct starfive_dwmac {struct device *dev;struct clk *clk_tx;
@@ -44,6 +48,48 @@ static void starfive_dwmac_fix_mac_speed(void *priv, unsigned int speed)dev_err (dwmac->dev,"failed to set tx rate %lu\n" , rate); } +static int starfive_dwmac_set_mode (struct plat_stmmacenet_data *plat_dat) +{ +struct starfive_dwmac *dwmac = plat_dat->bsp_priv; +struct regmap *regmap; +unsigned int args[2 ]; +unsigned int mode; +int err; + +switch (plat_dat->interface) { +case PHY_INTERFACE_MODE_RMII : + mode =STARFIVE_DWMAC_PHY_INFT_RMII ; +break ; + +case PHY_INTERFACE_MODE_RGMII : +case PHY_INTERFACE_MODE_RGMII_ID : + mode =STARFIVE_DWMAC_PHY_INFT_RGMII ; +break ; + +default : +dev_err (dwmac->dev,"unsupported interface %d\n" , + plat_dat->interface); +return -EINVAL ; + } + + regmap =syscon_regmap_lookup_by_phandle_args (dwmac->dev->of_node, +"starfive,syscon" , +2 , args); +if (IS_ERR (regmap)) { +dev_err (dwmac->dev,"syscon regmap failed.\n" ); +return -ENXIO ; + } + +/* args[0]:offset args[1]: shift */ + err =regmap_update_bits (regmap, args[0 ], +STARFIVE_DWMAC_PHY_INFT_FIELD << args[1 ], + mode << args[1 ]); +if (err) +return dev_err_probe (dwmac->dev, err,"error setting phy mode\n" ); + +return 0 ; +} +static int starfive_dwmac_probe (struct platform_device *pdev) {struct plat_stmmacenet_data *plat_dat;
@@ -89,6 +135,8 @@ static int starfive_dwmac_probe(struct platform_device *pdev) plat_dat->bsp_priv = dwmac; plat_dat->dma_cfg->dche = true; +starfive_dwmac_set_mode (plat_dat); + err =stmmac_dvr_probe (&pdev->dev, plat_dat, &stmmac_res);if (err) {stmmac_remove_config_dt (pdev, plat_dat);
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv