enable DMA and CPSW nodes for am62ax SoC family
Subsystems (3)
v2 cover enable DMA and CPSW nodes for am62ax SoC family
Hello again everyone!
This patch series syncs TI's am62ax device tree files with what has been merged in the v6.3-rc4 of the Linux Kernel. This series will also enable YMODEM support to make automated testing (which uses the UART boot method to load the bootloaders)
Thanks for reviewing
~Bryan
Changed from v1: [0]
o Rebased on top of -next branch
o dropped 'u-boot,dm-spl' for the new 'bootph-pre-ram' properties
[0] https://lore.kernel.org/u-boot/[email protected]/
Bryan Brattlof (4):
arm: dts: sync am62ax dtbs with linux v6.3-rc4
arm: dts: add DMA and CPSW nodes for uboot
configs: enable net features for am62ax
configs: am62ax: enable ymodem support for a53 spl
Vignesh Raghavendra (1):
dma: ti: k3-udma: Introduce DMA support for the am62ax
arch/arm/dts/k3-am62a-main.dtsi | 365 ++++++++++++++++++++++++++ arch/arm/dts/k3-am62a-mcu.dtsi | 51 ++++ arch/arm/dts/k3-am62a-wakeup.dtsi | 2 +- arch/arm/dts/k3-am62a7-r5-sk.dts | 8 + arch/arm/dts/k3-am62a7-sk-u-boot.dtsi | 26 +- arch/arm/dts/k3-am62a7-sk.dts | 70 +++++ arch/arm/dts/k3-am62a7.dtsi | 1 + configs/am62ax_evm_a53_defconfig | 7 +- drivers/dma/ti/Makefile | 1 + drivers/dma/ti/k3-psil-am62a.c | 196 ++++++++++++++ drivers/dma/ti/k3-psil-priv.h | 1 + drivers/dma/ti/k3-psil.c | 2 + 12 files changed, 727 insertions(+), 3 deletions(-) create mode 100644 drivers/dma/ti/k3-psil-am62a.c
base-commit: 942ac73afc37fb98695af4489ea1549c21615a5e
Signature · 1 line
2.40.0
PATCH v2 1/5 dma: ti: k3-udma: Introduce DMA support for the am62ax
From: Vignesh Raghavendra <[email protected]>
In preparation for enabling ethernet for the am62ax family of SoCs, introduce the initial DMA channel settings for the am62ax
--- drivers/dma/ti/Makefile | 1 + drivers/dma/ti/k3-psil-am62a.c | 196 +++++++++++++++++++++++++++++++++ drivers/dma/ti/k3-psil-priv.h | 1 + drivers/dma/ti/k3-psil.c | 2 + 4 files changed, 200 insertions(+) create mode 100644 drivers/dma/ti/k3-psil-am62a.c
drivers/dma/ti/Makefile +1 -0
@@ -8,3 +8,4 @@ k3-psil-data-$(CONFIG_SOC_K3_J721E) += k3-psil-j721e.o k3-psil-data-$(CONFIG_SOC_K3_J721S2) += k3-psil-j721s2.o k3-psil-data-$(CONFIG_SOC_K3_AM642) += k3-psil-am64.o k3-psil-data-$(CONFIG_SOC_K3_AM625) += k3-psil-am62.o +k3-psil-data-$(CONFIG_SOC_K3_AM62A7) += k3-psil-am62a.o
drivers/dma/ti/k3-psil-am62a.c new file +196 -0
196 lines not on this page · raw message
drivers/dma/ti/k3-psil-priv.h +1 -0
@@ -42,5 +42,6 @@ extern struct psil_ep_map j721e_ep_map;extern struct psil_ep_map j721s2_ep_map;extern struct psil_ep_map am64_ep_map;extern struct psil_ep_map am62_ep_map; +extern struct psil_ep_map am62a_ep_map;#endif /* K3_PSIL_PRIV_H_ */
drivers/dma/ti/k3-psil.c +2 -0
@@ -26,6 +26,8 @@ struct psil_endpoint_config *psil_get_ep_config(u32 thread_id) soc_ep_map = &am64_ep_map; else if (IS_ENABLED(CONFIG_SOC_K3_AM625)) soc_ep_map = &am62_ep_map; + else if (IS_ENABLED(CONFIG_SOC_K3_AM62A7)) + soc_ep_map = &am62a_ep_map; }if (thread_id &K3_PSIL_DST_THREAD_ID_OFFSET && soc_ep_map->dst) {
Signature · 1 line
2.40.0
PATCH v2 2/5 arm: dts: sync am62ax dtbs with linux v6.3-rc4
In reply to Bryan BrattlofTo enable Ethernet support at the uboot level, pull the device tree files from the v6.3-rc4 version of the Linux kernel.
--- arch/arm/dts/k3-am62a-main.dtsi | 365 ++++++++++++++++++++++++++++++ arch/arm/dts/k3-am62a-mcu.dtsi | 51 +++++ arch/arm/dts/k3-am62a-wakeup.dtsi | 2 +- arch/arm/dts/k3-am62a7-sk.dts | 70 ++++++ arch/arm/dts/k3-am62a7.dtsi | 1 + 5 files changed, 488 insertions(+), 1 deletion(-)
arch/arm/dts/k3-am62a-main.dtsi +365 -0
@@ -48,6 +48,18 @@ #address-cells = <1>; #size-cells = <1>; ranges = <0x00 0x00 0x00100000 0x20000>; + + phy_gmii_sel: phy@4044 { + compatible = "ti,am654-phy-gmii-sel"; + reg = <0x4044 0x8>; + #phy-cells = <1>; + }; + + epwm_tbclk: clock-controller@4130 { + compatible = "ti,am62-epwm-tbclk", "syscon"; + reg = <0x4130 0x4>; + #clock-cells = <1>; + }; }; dmss: bus@48000000 {
@@ -69,6 +81,67 @@ interrupt-names = "rx_012"; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; }; + + inta_main_dmss: interrupt-controller@48000000 { + compatible = "ti,sci-inta"; + reg = <0x00 0x48000000 0x00 0x100000>; + #interrupt-cells = <0>; + interrupt-controller; + interrupt-parent = <&gic500>; + msi-controller; + ti,sci = <&dmsc>; + ti,sci-dev-id = <28>; + ti,interrupt-ranges = <6 70 34>; + ti,unmapped-event-sources = <&main_bcdma>, <&main_pktdma>; + }; + + main_bcdma: dma-controller@485c0100 { + compatible = "ti,am64-dmss-bcdma"; + reg = <0x00 0x485c0100 0x00 0x100>, + <0x00 0x4c000000 0x00 0x20000>, + <0x00 0x4a820000 0x00 0x20000>, + <0x00 0x4aa40000 0x00 0x20000>, + <0x00 0x4bc00000 0x00 0x100000>; + reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt", "ringrt"; + msi-parent = <&inta_main_dmss>; + #dma-cells = <3>; + ti,sci = <&dmsc>; + ti,sci-dev-id = <26>; + ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */ + ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */ + ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */ + }; + + main_pktdma: dma-controller@485c0000 { + compatible = "ti,am64-dmss-pktdma"; + reg = <0x00 0x485c0000 0x00 0x100>, + <0x00 0x4a800000 0x00 0x20000>, + <0x00 0x4aa00000 0x00 0x40000>, + <0x00 0x4b800000 0x00 0x400000>; + reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt"; + msi-parent = <&inta_main_dmss>; + #dma-cells = <2>; + ti,sci = <&dmsc>; + ti,sci-dev-id = <30>; + ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */ + <0x24>, /* CPSW_TX_CHAN */ + <0x25>, /* SAUL_TX_0_CHAN */ + <0x26>; /* SAUL_TX_1_CHAN */ + ti,sci-rm-range-tflow = <0x10>, /* RING_UNMAPPED_TX_CHAN */ + <0x11>, /* RING_CPSW_TX_CHAN */ + <0x12>, /* RING_SAUL_TX_0_CHAN */ + <0x13>; /* RING_SAUL_TX_1_CHAN */ + ti,sci-rm-range-rchan = <0x29>, /* UNMAPPED_RX_CHAN */ + <0x2b>, /* CPSW_RX_CHAN */ + <0x2d>, /* SAUL_RX_0_CHAN */ + <0x2f>, /* SAUL_RX_1_CHAN */ + <0x31>, /* SAUL_RX_2_CHAN */ + <0x33>; /* SAUL_RX_3_CHAN */ + ti,sci-rm-range-rflow = <0x2a>, /* FLOW_UNMAPPED_RX_CHAN */ + <0x2c>, /* FLOW_CPSW_RX_CHAN */ + <0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */ + <0x32>; /* FLOW_SAUL_RX_2/3_CHAN */ + }; }; dmsc: system-controller@44043000 {
@@ -222,6 +295,39 @@ status = "disabled"; }; + main_spi0: spi@20100000 { + compatible = "ti,am654-mcspi", "ti,omap4-mcspi"; + reg = <0x00 0x20100000 0x00 0x400>; + interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 141 0>; + status = "disabled"; + }; + + main_spi1: spi@20110000 { + compatible = "ti,am654-mcspi","ti,omap4-mcspi"; + reg = <0x00 0x20110000 0x00 0x400>; + interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 142 0>; + status = "disabled"; + }; + + main_spi2: spi@20120000 { + compatible = "ti,am654-mcspi","ti,omap4-mcspi"; + reg = <0x00 0x20120000 0x00 0x400>; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 143 0>; + status = "disabled"; + }; + main_gpio_intr: interrupt-controller@a00000 { compatible = "ti,sci-intr"; reg = <0x00 0x00a00000 0x00 0x800>;
@@ -295,4 +401,263 @@ no-1-8-v; status = "disabled"; }; + + usbss0: dwc3-usb@f900000 { + compatible = "ti,am62-usb"; + reg = <0x00 0x0f900000 0x00 0x800>; + clocks = <&k3_clks 161 3>; + clock-names = "ref"; + ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>; + #address-cells = <2>; + #size-cells = <2>; + power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>; + ranges; + status = "disabled"; + + usb0: usb@31000000 { + compatible = "snps,dwc3"; + reg =<0x00 0x31000000 0x00 0x50000>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */ + interrupt-names = "host", "peripheral"; + maximum-speed = "high-speed"; + dr_mode = "otg"; + }; + }; + + usbss1: dwc3-usb@f910000 { + compatible = "ti,am62-usb"; + reg = <0x00 0x0f910000 0x00 0x800>; + clocks = <&k3_clks 162 3>; + clock-names = "ref"; + ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>; + #address-cells = <2>; + #size-cells = <2>; + power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>; + ranges; + status = "disabled"; + + usb1: usb@31100000 { + compatible = "snps,dwc3"; + reg =<0x00 0x31100000 0x00 0x50000>; + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ + <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */ + interrupt-names = "host", "peripheral"; + maximum-speed = "high-speed"; + dr_mode = "otg"; + }; + }; + + fss: bus@fc00000 { + compatible = "simple-bus"; + reg = <0x00 0x0fc00000 0x00 0x70000>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + ospi0: spi@fc40000 { + compatible = "ti,am654-ospi", "cdns,qspi-nor"; + reg = <0x00 0x0fc40000 0x00 0x100>, + <0x05 0x00000000 0x01 0x00000000>; + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; + cdns,fifo-depth = <256>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x0>; + clocks = <&k3_clks 75 7>; + assigned-clocks = <&k3_clks 75 7>; + assigned-clock-parents = <&k3_clks 75 8>; + assigned-clock-rates = <166666666>; + power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + cpsw3g: ethernet@8000000 { + compatible = "ti,am642-cpsw-nuss"; + #address-cells = <2>; + #size-cells = <2>; + reg = <0x0 0x8000000 0x0 0x200000>; + reg-names = "cpsw_nuss"; + ranges = <0x0 0x0 0x0 0x8000000 0x0 0x200000>; + clocks = <&k3_clks 13 0>; + assigned-clocks = <&k3_clks 13 3>; + assigned-clock-parents = <&k3_clks 13 11>; + clock-names = "fck"; + power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>; + status = "disabled"; + + dmas = <&main_pktdma 0xc600 15>, + <&main_pktdma 0xc601 15>, + <&main_pktdma 0xc602 15>, + <&main_pktdma 0xc603 15>, + <&main_pktdma 0xc604 15>, + <&main_pktdma 0xc605 15>, + <&main_pktdma 0xc606 15>, + <&main_pktdma 0xc607 15>, + <&main_pktdma 0x4600 15>; + dma-names = "tx0", "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", + "tx7", "rx"; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + cpsw_port1: port@1 { + reg = <1>; + ti,mac-only; + label = "port1"; + phys = <&phy_gmii_sel 1>; + mac-address = [00 00 00 00 00 00]; + ti,syscon-efuse = <&wkup_conf 0x200>; + }; + + cpsw_port2: port@2 { + reg = <2>; + ti,mac-only; + label = "port2"; + phys = <&phy_gmii_sel 2>; + mac-address = [00 00 00 00 00 00]; + }; + }; + + cpsw3g_mdio: mdio@f00 { + compatible = "ti,cpsw-mdio","ti,davinci_mdio"; + reg = <0x0 0xf00 0x0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&k3_clks 13 0>; + clock-names = "fck"; + bus_freq = <1000000>; + }; + + cpts@3d000 { + compatible = "ti,j721e-cpts"; + reg = <0x0 0x3d000 0x0 0x400>; + clocks = <&k3_clks 13 3>; + clock-names = "cpts"; + interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cpts"; + ti,cpts-ext-ts-inputs = <4>; + ti,cpts-periodic-outputs = <2>; + }; + }; + + hwspinlock: spinlock@2a000000 { + compatible = "ti,am64-hwspinlock"; + reg = <0x00 0x2a000000 0x00 0x1000>; + #hwlock-cells = <1>; + }; + + mailbox0_cluster0: mailbox@29000000 { + compatible = "ti,am64-mailbox"; + reg = <0x00 0x29000000 0x00 0x200>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <16>; + }; + + mailbox0_cluster1: mailbox@29010000 { + compatible = "ti,am64-mailbox"; + reg = <0x00 0x29010000 0x00 0x200>; + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <16>; + }; + + mailbox0_cluster2: mailbox@29020000 { + compatible = "ti,am64-mailbox"; + reg = <0x00 0x29020000 0x00 0x200>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <16>; + }; + + mailbox0_cluster3: mailbox@29030000 { + compatible = "ti,am64-mailbox"; + reg = <0x00 0x29030000 0x00 0x200>; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <16>; + }; + + main_mcan0: can@20701000 { + compatible = "bosch,m_can"; + reg = <0x00 0x20701000 0x00 0x200>, + <0x00 0x20708000 0x00 0x8000>; + reg-names = "m_can", "message_ram"; + power-domains = <&k3_pds 98 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 98 6>, <&k3_clks 98 1>; + clock-names = "hclk", "cclk"; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "int0", "int1"; + bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>; + status = "disabled"; + }; + + epwm0: pwm@23000000 { + compatible = "ti,am64-epwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x00 0x23000000 0x00 0x100>; + power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>; + clocks = <&epwm_tbclk 0>, <&k3_clks 86 0>; + clock-names = "tbclk", "fck"; + status = "disabled"; + }; + + epwm1: pwm@23010000 { + compatible = "ti,am64-epwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x00 0x23010000 0x00 0x100>; + power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>; + clocks = <&epwm_tbclk 1>, <&k3_clks 87 0>; + clock-names = "tbclk", "fck"; + status = "disabled"; + }; + + epwm2: pwm@23020000 { + compatible = "ti,am64-epwm", "ti,am3352-ehrpwm"; + #pwm-cells = <3>; + reg = <0x00 0x23020000 0x00 0x100>; + power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>; + clocks = <&epwm_tbclk 2>, <&k3_clks 88 0>; + clock-names = "tbclk", "fck"; + status = "disabled"; + }; + + ecap0: pwm@23100000 { + compatible = "ti,am3352-ecap"; + #pwm-cells = <3>; + reg = <0x00 0x23100000 0x00 0x100>; + power-domains = <&k3_pds 51 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 51 0>; + clock-names = "fck"; + status = "disabled"; + }; + + ecap1: pwm@23110000 { + compatible = "ti,am3352-ecap"; + #pwm-cells = <3>; + reg = <0x00 0x23110000 0x00 0x100>; + power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 52 0>; + clock-names = "fck"; + status = "disabled"; + }; + + ecap2: pwm@23120000 { + compatible = "ti,am3352-ecap"; + #pwm-cells = <3>; + reg = <0x00 0x23120000 0x00 0x100>; + power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 53 0>; + clock-names = "fck"; + status = "disabled"; + }; };
arch/arm/dts/k3-am62a-mcu.dtsi +51 -0
55 lines not on this page · raw message
arch/arm/dts/k3-am62a-wakeup.dtsi +1 -1
@@ -31,7 +31,7 @@ wkup_i2c0: i2c@2b200000 { compatible = "ti,am64-i2c", "ti,omap4-i2c"; - reg = <0x00 0x02b200000 0x00 0x100>; + reg = <0x00 0x2b200000 0x00 0x100>; interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>;
arch/arm/dts/k3-am62a7-sk.dts +70 -0
85 lines not on this page · raw message
arch/arm/dts/k3-am62a7.dtsi +1 -0
@@ -95,6 +95,7 @@ L2_0: l2-cache0 { compatible = "cache"; + cache-unified; cache-level = <2>; cache-size = <0x40000>; cache-line-size = <64>;
Signature · 1 line
2.40.0
Re: [PATCH v2 2/5] arm: dts: sync am62ax dtbs with linux v6.3-rc4
Hi Tom
On April 2, 2023 thus sayeth Bryan Brattlof:
Quoted 12 lines
To enable Ethernet support at the uboot level, pull the device tree files from the v6.3-rc4 version of the Linux kernel.
Signed-off-by Bryan Brattlof <[email protected]>--- arch/arm/dts/k3-am62a-main.dtsi | 365 ++++++++++++++++++++++++++++++ arch/arm/dts/k3-am62a-mcu.dtsi | 51 +++++ arch/arm/dts/k3-am62a-wakeup.dtsi | 2 +- arch/arm/dts/k3-am62a7-sk.dts | 70 ++++++ arch/arm/dts/k3-am62a7.dtsi | 1 + 5 files changed, 488 insertions(+), 1 deletion(-)
I'm going to update this to pull in v6.3-rc6 to align with what Nishanth and Andrew have been doing so all the SoCs will be on the same tag
~Bryan
PATCH v2 3/5 arm: dts: add DMA and CPSW nodes for uboot
In reply to Bryan BrattlofUpdate the uboot dtsi to enable DMA and CPSW at the uboot level
--- arch/arm/dts/k3-am62a7-r5-sk.dts | 8 ++++++++ arch/arm/dts/k3-am62a7-sk-u-boot.dtsi | 26 +++++++++++++++++++++++++- 2 files changed, 33 insertions(+), 1 deletion(-)
arch/arm/dts/k3-am62a7-r5-sk.dts +8 -0
@@ -143,3 +143,11 @@ status = "okay"; bootph-pre-ram; }; + +&main_pktdma { + ti,sci = <&dm_tifs>; +}; + +&main_bcdma { + ti,sci = <&dm_tifs>; +};
arch/arm/dts/k3-am62a7-sk-u-boot.dtsi +25 -1
@@ -15,7 +15,7 @@ }; }; -&cbass_main{ +&cbass_main { bootph-pre-ram; timer1: timer@2400000 {
@@ -138,3 +138,27 @@ &vdd_mmc1 { bootph-pre-ram; }; + +&main_bcdma { + bootph-pre-ram; +}; + +&main_pktdma { + bootph-pre-ram; +}; + +&cpsw3g { + reg = <0x00 0x08000000 0x00 0x200000>, + <0x00 0x43000200 0x00 0x8>; + reg-names = "cpsw_nuss", "mac_efuse"; + /delete-property/ ranges; + pinctrl-0 = <&main_mdio1_pins_default + &main_rgmii1_pins_default>; + bootph-pre-ram; + + cpsw-phy-sel@04044 { + compatible = "ti,am64-phy-gmii-sel"; + reg = <0x00 0x00104044 0x00 0x8>; + bootph-pre-ram; + }; +};
Signature · 1 line
2.40.0
PATCH v2 4/5 configs: enable net features for am62ax
In reply to Bryan BrattlofEnable DMA and CPSW options we now support for the am62ax SoC family
--- configs/am62ax_evm_a53_defconfig | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
configs/am62ax_evm_a53_defconfig +5 -1
@@ -40,7 +40,6 @@ CONFIG_SPL_OF_CONTROL=y CONFIG_MULTI_DTB_FIT=y CONFIG_SPL_MULTI_DTB_FIT=y CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y -# CONFIG_NET is not set CONFIG_SPL_DM=y CONFIG_SPL_DM_SEQ_ALIAS=y CONFIG_REGMAP=y
@@ -49,15 +48,20 @@ CONFIG_SPL_OF_TRANSLATE=y CONFIG_CLK=y CONFIG_SPL_CLK=y CONFIG_CLK_TI_SCI=y +CONFIG_DMA_CHANNELS=y +CONFIG_TI_K3_NAVSS_UDMA=y CONFIG_TI_SCI_PROTOCOL=y # CONFIG_GPIO is not set # CONFIG_I2C is not set CONFIG_DM_MAILBOX=y CONFIG_K3_SEC_PROXY=y +# CONFIG_SPL_MISC is not set CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ADMA=y CONFIG_SPL_MMC_SDHCI_ADMA=y CONFIG_MMC_SDHCI_AM654=y +CONFIG_PHY_TI_DP83867=y +CONFIG_TI_AM65_CPSW_NUSS=y CONFIG_PINCTRL=y CONFIG_SPL_PINCTRL=y CONFIG_PINCTRL_SINGLE=y
Signature · 1 line
2.40.0
PATCH v2 5/5 configs: am62ax: enable ymodem support for a53 spl
In reply to Bryan BrattlofAutomated testing inside TI currently relies on loading the boot-loaders into the SoC via UART. Enable SPL_YMODEM_SUPPORT so our testing infrastructure can boot (and test) our boards.
--- configs/am62ax_evm_a53_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/am62ax_evm_a53_defconfig +1 -0
@@ -34,6 +34,7 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400 CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot.img" CONFIG_SPL_DM_MAILBOX=y CONFIG_SPL_POWER_DOMAIN=y +CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_CMD_MMC=y CONFIG_OF_CONTROL=y CONFIG_SPL_OF_CONTROL=y
Signature · 1 line
2.40.0
Bryan,
Quoted 42 lines · Bryan Brattlof
Hello again everyone!
This patch series syncs TI's am62ax device tree files with what has been merged in the v6.3-rc4 of the Linux Kernel. This series will also enable YMODEM support to make automated testing (which uses the UART boot method to load the bootloaders)
Thanks for reviewing
~BryanChanged from v1: [0]
o Rebased on top of -next branch
o dropped 'u-boot,dm-spl' for the new 'bootph-pre-ram' properties[0] https://lore.kernel.org/u-boot/[email protected]/
Bryan Brattlof (4):
arm: dts: sync am62ax dtbs with linux v6.3-rc4
arm: dts: add DMA and CPSW nodes for uboot
configs: enable net features for am62ax
configs: am62ax: enable ymodem support for a53 splVignesh Raghavendra (1):
dma: ti: k3-udma: Introduce DMA support for the am62axarch/arm/dts/k3-am62a-main.dtsi | 365 ++++++++++++++++++++++++++ arch/arm/dts/k3-am62a-mcu.dtsi | 51 ++++ arch/arm/dts/k3-am62a-wakeup.dtsi | 2 +- arch/arm/dts/k3-am62a7-r5-sk.dts | 8 + arch/arm/dts/k3-am62a7-sk-u-boot.dtsi | 26 +- arch/arm/dts/k3-am62a7-sk.dts | 70 +++++ arch/arm/dts/k3-am62a7.dtsi | 1 + configs/am62ax_evm_a53_defconfig | 7 +- drivers/dma/ti/Makefile | 1 + drivers/dma/ti/k3-psil-am62a.c | 196 ++++++++++++++ drivers/dma/ti/k3-psil-priv.h | 1 + drivers/dma/ti/k3-psil.c | 2 + 12 files changed, 727 insertions(+), 3 deletions(-) create mode 100644 drivers/dma/ti/k3-psil-am62a.c
Quoted 1 line
base-commit:
942ac73afc37fb98695af4489ea1549c21615a5e
Signature · 2 lines
Regards, Ravi