Adjust the dma-ranges for MTK IOMMU
Subsystems (7)
Yong Wu
maintainerv6 cover Adjust the dma-ranges for MTK IOMMU
After commit f1ad5338a4d5 ("of: Fix "dma-ranges" handling for bus controllers"), the dma-ranges is not allowed for dts leaf node. but we still would like to separate the different masters into different iova regions. Thus we adjust the internal flow, separate the 16GB iova range by the master HW larbid/portid and add the dma-ranges property in the parent "soc" node. This also could avoid the users forget/abuse the iova regions.
The commit f1ad5338a4d5 did affect the mt8195 venc, But it is not a fatal issue, it could also work well at 0-4GB iova. thus I don't add "Fixes:" tag.
In this series, I add functions for mt8192/mt8195/mt8186, mt8188 will be in its special patchset. and the previous mt8173/mt8183...support 0-4GB only, no need this function.
Change note:
v6: Add three patches[9/10/11] for set dma-mask for iommu master devices.
v5: Nothing change. Just rebase on v6.3-rc1.
v4: https://lore.kernel.org/linux-mediatek/[email protected]/
Improve the comment in the code from AngeloGioacchino.
v3: https://lore.kernel.org/linux-mediatek/[email protected]/
Add a new patch only for comment more in the code.
v2: https://lore.kernel.org/linux-mediatek/[email protected]/
a) Base on next-20230206 since mt8195 jpeg node is applied which affect this patch.
b) Reword the commit message [1/10][2/10] to explain effect.
v1: https://lore.kernel.org/linux-mediatek/[email protected]/
Base on v6.2-rc3.
Yong Wu (14):
dt-bindings: media: mediatek,vcodec: Remove dma-ranges property
dt-bindings: media: mediatek,jpeg: Remove dma-ranges property iommu/mediatek: Improve comment for the current region/bank iommu/mediatek: Get regionid from larb/port id iommu/mediatek: mt8192: Add iova_region_larb_msk iommu/mediatek: mt8195: Add iova_region_larb_msk iommu/mediatek: mt8186: Add iova_region_larb_msk iommu/mediatek: Add a gap for the iova regions iommu/mediatek: Set dma_mask for the master devices
media: mtk-jpegdec: Remove the setting for dma_mask
media: mediatek: vcodec: Remove the setting for dma_mask
arm64: dts: mt8195: Remove the unnecessary dma-ranges
arm64: dts: mt8195: Add dma-ranges for the parent "soc" node
arm64: dts: mt8186: Add dma-ranges for the parent "soc" node
.../media/mediatek,mt8195-jpegdec.yaml | 7 - .../media/mediatek,mt8195-jpegenc.yaml | 7 - .../media/mediatek,vcodec-decoder.yaml | 5 - .../media/mediatek,vcodec-encoder.yaml | 5 - .../media/mediatek,vcodec-subdev-decoder.yaml | 7 - .../bindings/media/mediatek-jpeg-encoder.yaml | 5 - arch/arm64/boot/dts/mediatek/mt8186.dtsi | 1 + arch/arm64/boot/dts/mediatek/mt8195.dtsi | 4 +- drivers/iommu/mtk_iommu.c | 145 ++++++++++++++---- .../platform/mediatek/jpeg/mtk_jpeg_core.c | 3 - .../mediatek/vcodec/mtk_vcodec_dec_drv.c | 8 - .../mediatek/vcodec/mtk_vcodec_enc_drv.c | 3 - 12 files changed, 117 insertions(+), 83 deletions(-)
Signature · 1 line
2.18.0
Yong Wu
maintainerPATCH v6 1/14 dt-bindings: media: mediatek,vcodec: Remove dma-ranges property
After commit f1ad5338a4d5 ("of: Fix "dma-ranges" handling for bus controllers"), the dma-ranges of the leaf node doesn't work. Remove it for vcodec here.
1) For mediatek,vcodec-decoder.yaml and mediatek,vcodec-encoder.yaml, this property is in the leaf node, it is invalid as the above comment.
Currently there is only mt8195 VENC node has this property in upstream. Indeed, VENC is affected, but it is not a fatal issue. Originally it expects its iova range locate at 4GB-8GB. However after that commit, its expectation doesn't come true, it will fall back to 0-4GB iova and also could work well.
2) For mediatek,vcodec-subdev-decoder.yaml, It already uses parent-child node, this property works. Instead, MediaTek iommu will control the masters' iova ranges by the master's larb/port id internally, then the dma-ranges property is unnecessary for the master's node.
--- .../devicetree/bindings/media/mediatek,vcodec-decoder.yaml | 5 ----- .../devicetree/bindings/media/mediatek,vcodec-encoder.yaml | 5 ----- .../bindings/media/mediatek,vcodec-subdev-decoder.yaml | 7 ------- 3 files changed, 17 deletions(-)
Documentation/devicetree/bindings/media/mediatek,vcodec-decoder.yaml +0 -5
@@ -56,11 +56,6 @@ properties: List of the hardware port in respective IOMMU block for current Socs. Refer to bindings/iommu/mediatek,iommu.yaml. - dma-ranges: - maxItems: 1 - description: | - Describes the physical address space of IOMMU maps to memory. - mediatek,vpu: $ref: /schemas/types.yaml#/definitions/phandle description:
Documentation/devicetree/bindings/media/mediatek,vcodec-encoder.yaml +0 -5
@@ -49,11 +49,6 @@ properties: List of the hardware port in respective IOMMU block for current Socs. Refer to bindings/iommu/mediatek,iommu.yaml. - dma-ranges: - maxItems: 1 - description: | - Describes the physical address space of IOMMU maps to memory. - mediatek,vpu: $ref: /schemas/types.yaml#/definitions/phandle description:
Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml +0 -7
@@ -76,11 +76,6 @@ properties: The node of system control processor (SCP), using the remoteproc & rpmsg framework. - dma-ranges: - maxItems: 1 - description: | - Describes the physical address space of IOMMU maps to memory. - "#address-cells": const: 2
@@ -203,7 +198,6 @@ required: - reg - iommus - mediatek,scp - - dma-ranges - ranges if:
@@ -236,7 +230,6 @@ examples: compatible = "mediatek,mt8192-vcodec-dec"; mediatek,scp = <&scp>; iommus = <&iommu0 M4U_PORT_L4_VDEC_MC_EXT>; - dma-ranges = <0x1 0x0 0x0 0x40000000 0x0 0xfff00000>; #address-cells = <2>; #size-cells = <2>; ranges = <0 0 0 0x16000000 0 0x40000>;
Signature · 1 line
2.25.1
Re: [PATCH v6 01/14] dt-bindings: media: mediatek,vcodec: Remove dma-ranges property
On Mon, Apr 03, 2023 at 05:13:24PM +0800, Yong Wu wrote:
[..]
Quoted 23 lines
Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml +0
-6@@ -76,11 +76,6 @@ properties: The node of system control processor (SCP), using the remoteproc & rpmsg framework. - dma-ranges: - maxItems: 1 - description: | - Describes the physical address space of IOMMU maps to memory. - "#address-cells": const: 2@@ -203,7 +198,6 @@ required: - reg - iommus - mediatek,scp - - dma-ranges - ranges if:
Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml examples: · line 235
Quoted 7 lines
Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml +0
-1@@ -236,7 +230,6 @@ examples: compatible = "mediatek,mt8192-vcodec-dec"; mediatek,scp = <&scp>; iommus = <&iommu0 M4U_PORT_L4_VDEC_MC_EXT>; - dma-ranges = <0x1 0x0 0x0 0x40000000 0x0 0xfff00000>; #address-cells = <2>; #size-cells = <2>; ranges = <0 0 0 0x16000000 0 0x40000>;
Hi,
this change was also done in another patch [1], and it is already queued for the media tree [2], so you'll need to remove this part of your patch in order to avoid conflicts.
[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/all/[email protected]/#t
Thanks,
Nícolas
Yong Wu (吴勇)
maintainerRe: [PATCH v6 01/14] dt-bindings: media: mediatek,vcodec: Remove dma-ranges property
Quoted 42 lines · Nícolas F. R. A. Prado
External email : Please do not click links or open attachments until you have verified the sender or the content.
On Mon, Apr 03, 2023 at 05:13:24PM +0800, Yong Wu wrote:
[..]Quoted 26 lines
--- a/Documentation/devicetree/bindings/media/mediatek,vcodec-
subdev-decoder.yaml
+++ b/Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yamlDocumentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml +0
-4@@ -76,11 +76,6 @@ properties: The node of system control processor (SCP), using the remoteproc & rpmsg framework. - dma-ranges: - maxItems: 1 - description: | - Describes the physical address space of IOMMU maps tomemory.
Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml +0
-2- "#address-cells": const: 2@@ -203,7 +198,6 @@ required: - reg - iommus - mediatek,scp - - dma-ranges - ranges if:Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml examples: · line 235
Quoted 7 lines
Documentation/devicetree/bindings/media/mediatek,vcodec-subdev-decoder.yaml +0
-1@@ -236,7 +230,6 @@ examples: compatible = "mediatek,mt8192-vcodec-dec"; mediatek,scp = <&scp>; iommus = <&iommu0 M4U_PORT_L4_VDEC_MC_EXT>; - dma-ranges = <0x1 0x0 0x0 0x40000000 0x0 0xfff00000>; #address-cells = <2>; #size-cells = <2>; ranges = <0 0 0 0x16000000 0 0x40000>;Hi,
Quoted 5 lines
this change was also done in another patch [1], and it is already queued for the
media tree [2], so you'll need to remove this part of your patch in order to
avoid conflicts.
Hi Nícolas,
Thanks a lot for this information. I will remove the change in this file.
Quoted 8 lines
[1]
https://lore.kernel.org/all/[email protected]/
[2]
https://lore.kernel.org/all/[email protected]/#tThanks,
Nícolas
Yong Wu
maintainerPATCH v6 2/14 dt-bindings: media: mediatek,jpeg: Remove dma-ranges property
In reply to Yong WuAfter commit f1ad5338a4d5 ("of: Fix "dma-ranges" handling for bus controllers"), the dma-ranges of the leaf node doesn't work. Remove it for jpeg here.
Currently there is only mt8195 jpeg node has this property in upstream, and it already uses parent-child node, this property did work. But instead, MediaTek iommu will control the masters' iova ranges by the master's larb/port id internally, then this property is unnecessary.
--- .../devicetree/bindings/media/mediatek,mt8195-jpegdec.yaml | 7 ------- .../devicetree/bindings/media/mediatek,mt8195-jpegenc.yaml | 7 ------- .../devicetree/bindings/media/mediatek-jpeg-encoder.yaml | 5 ----- 3 files changed, 19 deletions(-)
Documentation/devicetree/bindings/media/mediatek,mt8195-jpegdec.yaml +0 -7
@@ -26,11 +26,6 @@ properties: Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml for details. Ports are according to the HW. - dma-ranges: - maxItems: 1 - description: | - Describes the physical address space of IOMMU maps to memory. - "#address-cells": const: 2
@@ -89,7 +84,6 @@ required: - compatible - power-domains - iommus - - dma-ranges - ranges additionalProperties: false
@@ -115,7 +109,6 @@ examples: <&iommu_vpp M4U_PORT_L19_JPGDEC_BSDMA1>, <&iommu_vpp M4U_PORT_L19_JPGDEC_BUFF_OFFSET1>, <&iommu_vpp M4U_PORT_L19_JPGDEC_BUFF_OFFSET0>; - dma-ranges = <0x1 0x0 0x0 0x40000000 0x0 0xfff00000>; #address-cells = <2>; #size-cells = <2>; ranges;
Documentation/devicetree/bindings/media/mediatek,mt8195-jpegenc.yaml +0 -7
@@ -26,11 +26,6 @@ properties: Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml for details. Ports are according to the HW. - dma-ranges: - maxItems: 1 - description: | - Describes the physical address space of IOMMU maps to memory. - "#address-cells": const: 2
@@ -89,7 +84,6 @@ required: - compatible - power-domains - iommus - - dma-ranges - ranges additionalProperties: false
@@ -113,7 +107,6 @@ examples: <&iommu_vpp M4U_PORT_L20_JPGENC_C_RDMA>, <&iommu_vpp M4U_PORT_L20_JPGENC_Q_TABLE>, <&iommu_vpp M4U_PORT_L20_JPGENC_BSDMA>; - dma-ranges = <0x1 0x0 0x0 0x40000000 0x0 0xfff00000>; #address-cells = <2>; #size-cells = <2>; ranges;
Documentation/devicetree/bindings/media/mediatek-jpeg-encoder.yaml +0 -5
@@ -44,11 +44,6 @@ properties: Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml for details. Ports are according to the HW. - dma-ranges: - maxItems: 1 - description: | - Describes the physical address space of IOMMU maps to memory. - required: - compatible - reg
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 3/14 iommu/mediatek: Improve comment for the current region/bank
In reply to Yong WuNo functional change. Just add more comment about the current region/bank in the code.
--- drivers/iommu/mtk_iommu.c | 31 ++++++++++++++++++++++++++----- 1 file changed, 26 insertions(+), 5 deletions(-)
drivers/iommu/mtk_iommu.c +26 -5
@@ -197,12 +197,33 @@ struct mtk_iommu_plat_data {char *pericfg_comp_str;struct list_head *hw_list; -unsigned int iova_region_nr; -const struct mtk_iommu_iova_region *iova_region; -u8 banks_num; -bool banks_enable[MTK_IOMMU_BANK_MAX ]; -unsigned int banks_portmsk[MTK_IOMMU_BANK_MAX ]; +/* +* The IOMMU HW may support 16GB iova. In order to balance the IOVA ranges, +* different masters will be put in different iova ranges, for example vcodec +* is in 4G-8G and cam is in 8G-12G. Meanwhile, some masters may have the +* special IOVA range requirement, like CCU can only support the address +* 0x40000000-0x44000000. +* Here list the iova ranges this SoC supports and which larbs/ports are in +* which region. +* +* 16GB iova all use one pgtable, but each a region is a iommu group. +*/ +struct { +unsigned int iova_region_nr; +const struct mtk_iommu_iova_region *iova_region; + }; + +/* +* The IOMMU HW may have 5 banks. Each bank has a independent pgtable. +* Here list how many banks this SoC supports/enables and which ports are in which bank. +*/ +struct { +u8 banks_num; +bool banks_enable[MTK_IOMMU_BANK_MAX ]; +unsigned int banks_portmsk[MTK_IOMMU_BANK_MAX ]; + }; +unsigned char larbid_remap[MTK_LARB_COM_MAX ][MTK_LARB_SUBCOM_MAX ]; };
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 4/14 iommu/mediatek: Get regionid from larb/port id
In reply to Yong WuAfter commit f1ad5338a4d5 ("of: Fix "dma-ranges" handling for bus controllers"), the dma-ranges is not allowed for dts leaf node. but we still would like to separate to different masters into different iova regions.
Thus we have to separate it by the HW larbid and portid. For example, larb1/2 are in region2 and larb3 is in region3. The problem is that some ports inside a larb are in region4 while some ports inside this larb are in region5. Therefore I define a "iova_region_larb_msk" to help record the information for each a port. Take a example for a larb:
[1] = ~0: means all ports in this larb are in region1;
[2] = BIT(3) | BIT(4): means port3/4 in this larb are region2;
[3] = ~(BIT(3) | BIT(4)): means all the other ports except port3/4 in this larb are region3.
This method also avoids the users forget/abuse the iova regions.
--- drivers/iommu/mtk_iommu.c | 45 ++++++++++++++++++++++----------------- 1 file changed, 26 insertions(+), 19 deletions(-)
drivers/iommu/mtk_iommu.c +26 -19
@@ -8,7 +8,6 @@#include <linux/clk.h> #include <linux/component.h> #include <linux/device.h> -#include <linux/dma-direct.h> #include <linux/err.h> #include <linux/interrupt.h> #include <linux/io.h>
@@ -212,6 +211,15 @@ struct mtk_iommu_plat_data {struct {unsigned int iova_region_nr;const struct mtk_iommu_iova_region *iova_region; +/* +* Indicate the correspondance between larbs, ports and regions. +* +* The index is the same as iova_region and larb port numbers are +* described as bit positions. +* For example, storing BIT(0) at index 2,1 means "larb 1, port0 is in region 2". +* [2] = { [1] = BIT(0) } +*/ +const u32 (*iova_region_larb_msk)[MTK_LARB_NR_MAX ]; };/*
@@ -529,30 +537,29 @@ static unsigned int mtk_iommu_get_bank_id(struct device *dev,static int mtk_iommu_get_iova_region_id (struct device *dev,const struct mtk_iommu_plat_data *plat_data) { -const struct mtk_iommu_iova_region *rgn = plat_data->iova_region; -const struct bus_dma_region *dma_rgn = dev->dma_range_map; -int i, candidate =-1 ; -dma_addr_t dma_end; +struct iommu_fwspec *fwspec =dev_iommu_fwspec_get (dev); +unsigned int portidmsk =0 , larbid; +const u32 *rgn_larb_msk; +int i; -if (!dma_rgn || plat_data->iova_region_nr ==1 ) +if (plat_data->iova_region_nr ==1 )return 0 ; - dma_end = dma_rgn->dma_start + dma_rgn->size -1 ; -for (i =0 ; i < plat_data->iova_region_nr; i++, rgn++) { -/* Best fit. */ -if (dma_rgn->dma_start == rgn->iova_base && - dma_end == rgn->iova_base + rgn->size -1 ) + larbid =MTK_M4U_TO_LARB (fwspec->ids[0 ]); +for (i =0 ; i < fwspec->num_ids; i++) + portidmsk |=BIT (MTK_M4U_TO_PORT (fwspec->ids[i])); + +for (i =0 ; i < plat_data->iova_region_nr; i++) { + rgn_larb_msk = plat_data->iova_region_larb_msk[i]; +if (!rgn_larb_msk) +continue ; + +if ((rgn_larb_msk[larbid] & portidmsk) == portidmsk)return i; -/* ok if it is inside this region. */ -if (dma_rgn->dma_start >= rgn->iova_base && - dma_end < rgn->iova_base + rgn->size) - candidate = i; } -if (candidate >=0 ) -return candidate; -dev_err (dev,"Can NOT find the iommu domain id(%pad 0x%llx).\n" , - &dma_rgn->dma_start, dma_rgn->size); +dev_err (dev,"Can NOT find the region for larb(%d-%x).\n" , + larbid, portidmsk);return -EINVAL ; }
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 5/14 iommu/mediatek: mt8192: Add iova_region_larb_msk
In reply to Yong WuAdd iova_region_larb_msk for mt8192. We separate the 16GB iova regions by each device's larbid/portid.
Note: larb3/6/8/10/12/15 connect nothing in this SoC.
Refer to the comment in include/dt-bindings/memory/mt8192-larb-port.h
Define a new macro MT8192_MULTI_REGION_NR_MAX to indicate the index of mt8xxx_larb_region_msk and
"struct mtk_iommu_iova_region mt8192_multi_dom" are the same.
--- drivers/iommu/mtk_iommu.c | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-)
drivers/iommu/mtk_iommu.c +18 -1
@@ -336,7 +336,12 @@ static const struct mtk_iommu_iova_region single_domain[] = { {.iova_base = 0, .size = SZ_4G}, }; -static const struct mtk_iommu_iova_region mt8192_multi_dom[] = { +#define MT8192_MULTI_REGION_NR_MAX 6 + +#define MT8192_MULTI_REGION_NR (IS_ENABLED(CONFIG_ARCH_DMA_ADDR_T_64BIT) ? \ + MT8192_MULTI_REGION_NR_MAX : 1) + +static const struct mtk_iommu_iova_region mt8192_multi_dom[MT8192_MULTI_REGION_NR ] = { { .iova_base =0x0 , .size =SZ_4G },/* 0 ~ 4G */ #if IS_ENABLED(CONFIG_ARCH_DMA_ADDR_T_64BIT) { .iova_base = SZ_4G, .size = SZ_4G}, /* 4G ~ 8G */
@@ -1534,6 +1539,17 @@ static const struct mtk_iommu_plat_data mt8186_data_mm = { .iova_region_nr = ARRAY_SIZE(mt8192_multi_dom), }; +static const unsigned int mt8192_larb_region_msk[MT8192_MULTI_REGION_NR_MAX ][MTK_LARB_NR_MAX ] = { + [0 ] = {~0 , ~0 },/* Region0: larb0/1 */ + [1 ] = {0 ,0 ,0 ,0 , ~0 , ~0 ,0 , ~0 },/* Region1: larb4/5/7 */ + [2 ] = {0 ,0 , ~0 ,0 ,0 ,0 ,0 ,0 ,/* Region2: larb2/9/11/13/14/16/17/18/19/20 */ +0 , ~0 ,0 , ~0 ,0 , ~(u32)(BIT (9 ) |BIT (10 )), ~(u32)(BIT (4 ) |BIT (5 )),0 , + ~0 , ~0 , ~0 , ~0 , ~0 }, + [3 ] = {0 }, + [4 ] = {[13 ] =BIT (9 ) |BIT (10 )},/* larb13 port9/10 */ + [5 ] = {[14 ] =BIT (4 ) |BIT (5 )},/* larb14 port4/5 */ +}; +static const struct mtk_iommu_plat_data mt8192_data = { .m4u_plat =M4U_MT8192 , .flags = HAS_BCLK | HAS_SUB_COMM_2BITS | OUT_ORDER_WR_EN |
@@ -1543,6 +1559,7 @@ static const struct mtk_iommu_plat_data mt8192_data = { .banks_enable = {true}, .iova_region = mt8192_multi_dom, .iova_region_nr = ARRAY_SIZE(mt8192_multi_dom), + .iova_region_larb_msk = mt8192_larb_region_msk, .larbid_remap = {{0}, {1}, {4, 5}, {7}, {2}, {9, 11, 19, 20}, {0, 14, 16}, {0, 13, 18, 17}}, };
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 6/14 iommu/mediatek: mt8195: Add iova_region_larb_msk
In reply to Yong WuAdd iova_region_larb_msk for mt8195. We separate the 16GB iova regions by each device's larbid/portid.
Refer to include/dt-bindings/memory/mt8195-memory-port.h
--- drivers/iommu/mtk_iommu.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
drivers/iommu/mtk_iommu.c +17 -0
@@ -1579,6 +1579,21 @@ static const struct mtk_iommu_plat_data mt8195_data_infra = { .iova_region_nr = ARRAY_SIZE(single_domain), }; +static const unsigned int mt8195_larb_region_msk[MT8192_MULTI_REGION_NR_MAX ][MTK_LARB_NR_MAX ] = { + [0 ] = {~0 , ~0 , ~0 , ~0 },/* Region0: all ports for larb0/1/2/3 */ + [1 ] = {0 ,0 ,0 ,0 ,0 ,0 ,0 ,0 , +0 ,0 ,0 ,0 ,0 ,0 ,0 ,0 , +0 ,0 ,0 , ~0 , ~0 , ~0 , ~0 , ~0 ,/* Region1: larb19/20/21/22/23/24 */ + ~0 }, + [2 ] = {0 ,0 ,0 ,0 , ~0 , ~0 , ~0 , ~0 ,/* Region2: the other larbs. */ + ~0 , ~0 , ~0 , ~0 , ~0 , ~0 , ~0 , ~0 , + ~0 , ~0 ,0 ,0 ,0 ,0 ,0 ,0 , +0 , ~0 , ~0 , ~0 , ~0 }, + [3 ] = {0 }, + [4 ] = {[18 ] =BIT (0 ) |BIT (1 )},/* Only larb18 port0/1 */ + [5 ] = {[18 ] =BIT (2 ) |BIT (3 )},/* Only larb18 port2/3 */ +}; +static const struct mtk_iommu_plat_data mt8195_data_vdo = { .m4u_plat =M4U_MT8195 , .flags = HAS_BCLK | HAS_SUB_COMM_2BITS | OUT_ORDER_WR_EN |
@@ -1589,6 +1604,7 @@ static const struct mtk_iommu_plat_data mt8195_data_vdo = { .banks_enable = {true}, .iova_region = mt8192_multi_dom, .iova_region_nr = ARRAY_SIZE(mt8192_multi_dom), + .iova_region_larb_msk = mt8195_larb_region_msk, .larbid_remap = {{2, 0}, {21}, {24}, {7}, {19}, {9, 10, 11}, {13, 17, 15/* 17b */, 25}, {5}}, };
@@ -1603,6 +1619,7 @@ static const struct mtk_iommu_plat_data mt8195_data_vpp = { .banks_enable = {true}, .iova_region = mt8192_multi_dom, .iova_region_nr = ARRAY_SIZE(mt8192_multi_dom), + .iova_region_larb_msk = mt8195_larb_region_msk, .larbid_remap = {{1}, {3}, {22, MTK_INVALID_LARBID, MTK_INVALID_LARBID, MTK_INVALID_LARBID, 23}, {8}, {20}, {12},
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 7/14 iommu/mediatek: mt8186: Add iova_region_larb_msk
In reply to Yong WuAdd iova_region_larb_msk for mt8186. We separate the 16GB iova regions by each device's larbid/portid.
Note: larb5/6/10/12/14/15/18 connect nothing in this SoC. Refer to include/dt-bindings/memory/mt8186-memory-port.h
--- drivers/iommu/mtk_iommu.c | 13 +++++++++++++ 1 file changed, 13 insertions(+)
drivers/iommu/mtk_iommu.c +13 -0
@@ -1525,6 +1525,18 @@ static const struct mtk_iommu_plat_data mt8183_data = { .larbid_remap = {{0}, {4}, {5}, {6}, {7}, {2}, {3}, {1}}, }; +static const unsigned int mt8186_larb_region_msk[MT8192_MULTI_REGION_NR_MAX ][MTK_LARB_NR_MAX ] = { + [0 ] = {~0 , ~0 , ~0 },/* Region0: all ports for larb0/1/2 */ + [1 ] = {0 ,0 ,0 ,0 , ~0 ,0 ,0 , ~0 },/* Region1: larb4/7 */ + [2 ] = {0 ,0 ,0 ,0 ,0 ,0 ,0 ,0 ,/* Region2: larb8/9/11/13/16/17/19/20 */ + ~0 , ~0 ,0 , ~0 ,0 , ~(u32)(BIT (9 ) |BIT (10 )),0 ,0 , +/* larb13: the other ports except port9/10 */ + ~0 , ~0 ,0 , ~0 , ~0 }, + [3 ] = {0 }, + [4 ] = {[13 ] =BIT (9 ) |BIT (10 )},/* larb13 port9/10 */ + [5 ] = {[14 ] = ~0 },/* larb14 */ +}; +static const struct mtk_iommu_plat_data mt8186_data_mm = { .m4u_plat =M4U_MT8186 , .flags = HAS_BCLK | HAS_SUB_COMM_2BITS | OUT_ORDER_WR_EN |
@@ -1537,6 +1549,7 @@ static const struct mtk_iommu_plat_data mt8186_data_mm = { .banks_enable = {true}, .iova_region = mt8192_multi_dom, .iova_region_nr = ARRAY_SIZE(mt8192_multi_dom), + .iova_region_larb_msk = mt8186_larb_region_msk, }; static const unsigned int mt8192_larb_region_msk[MT8192_MULTI_REGION_NR_MAX][MTK_LARB_NR_MAX] = {
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 8/14 iommu/mediatek: Add a gap for the iova regions
In reply to Yong WuAs the removed property in the vcodec dt-binding, the property is:
dma-ranges = <0x1 0x0 0x0 0x40000000 0x0 0xfff00000>;
The length is 0xfff0_0000 rather than 0x1_0000_0000, this means it requires 1M as a gap. This is because the end address for some vcodec HW is (address + size). If the size is 4G, the end address may be 0x2_0000_0000, and the width for vcodec register only is 32, then the HW may get the ZERO address.
Currently the consumer's dma-ranges property doesn't work, IOMMU has to consider this case. Add a bigger gap(8M) for all the regions to avoid it.
--- drivers/iommu/mtk_iommu.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-)
drivers/iommu/mtk_iommu.c +7 -5
@@ -332,8 +332,10 @@ static LIST_HEAD(m4ulist); /* List all the M4U HWs */#define for_each_m4u (data, head) list_for_each_entry(data, head, list) +#define MTK_IOMMU_IOVA_SZ_4G (SZ_4G - SZ_8M)/* 8M as gap */ +static const struct mtk_iommu_iova_region single_domain[] = { - {.iova_base =0 , .size =SZ_4G }, + {.iova_base =0 , .size =MTK_IOMMU_IOVA_SZ_4G }, };#define MT8192_MULTI_REGION_NR_MAX 6
@@ -342,11 +344,11 @@ static const struct mtk_iommu_iova_region single_domain[] = { MT8192_MULTI_REGION_NR_MAX : 1)static const struct mtk_iommu_iova_region mt8192_multi_dom[MT8192_MULTI_REGION_NR ] = { - { .iova_base =0x0 , .size =SZ_4G },/* 0 ~ 4G */ + { .iova_base =0x0 , .size =MTK_IOMMU_IOVA_SZ_4G },/* 0 ~ 4G, */ #if IS_ENABLED(CONFIG_ARCH_DMA_ADDR_T_64BIT) - { .iova_base =SZ_4G , .size =SZ_4G },/* 4G ~ 8G */ - { .iova_base =SZ_4G *2 , .size =SZ_4G },/* 8G ~ 12G */ - { .iova_base =SZ_4G *3 , .size =SZ_4G },/* 12G ~ 16G */ + { .iova_base =SZ_4G , .size =MTK_IOMMU_IOVA_SZ_4G },/* 4G ~ 8G */ + { .iova_base =SZ_4G *2 , .size =MTK_IOMMU_IOVA_SZ_4G },/* 8G ~ 12G */ + { .iova_base =SZ_4G *3 , .size =MTK_IOMMU_IOVA_SZ_4G },/* 12G ~ 16G */ { .iova_base =0x240000000ULL , .size =0x4000000 },/* CCU0 */ { .iova_base = 0x244000000ULL, .size = 0x4000000}, /* CCU1 */
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 9/14 iommu/mediatek: Set dma_mask for the master devices
In reply to Yong WuMediaTek iommu arranges dma ranges for all the masters, this patch is to help them set dma mask. This is to avoid each master setting their own mask, but also to avoid a real issue, such as JPEG uses "mediatek,mtk-jpgenc" for 2701/8183/8186/8188, then JPEG could ignore its different dma_mask in different SoC to achieve common code.
--- drivers/iommu/mtk_iommu.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/iommu/mtk_iommu.c +8 -0
@@ -738,6 +738,14 @@ static int mtk_iommu_attach_device(struct iommu_domain *domain, }mutex_unlock (&data->mutex); +if (region_id >0 ) { + ret =dma_set_mask_and_coherent (dev,DMA_BIT_MASK (34 )); +if (ret) { +dev_err (m4udev,"Failed to set dma_mask for %s(%d).\n" ,dev_name (dev), ret); +return ret; + } + } +return mtk_iommu_config (data, dev, true, region_id); err_unlock:
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 10/14 media: mtk-jpegdec: Remove the setting for dma_mask
In reply to Yong WuIn order to simplify the masters to set their respective dma masks, MTK IOMMU helps to centralize the processing. Because all the dma ranges is set in IOMMU, IOMMU knows well the dma mask requirements of masters. After this patch, the masters code does not need care dma-ranges/dma_mask related information.
--- drivers/media/platform/mediatek/jpeg/mtk_jpeg_core.c | 3 --- 1 file changed, 3 deletions(-)
drivers/media/platform/mediatek/jpeg/mtk_jpeg_core.c +0 -3
@@ -1757,9 +1757,6 @@ static int mtk_jpeg_probe(struct platform_device *pdev) jpeg->vdev->device_caps =V4L2_CAP_STREAMING |V4L2_CAP_VIDEO_M2M_MPLANE ; -if (of_get_property (pdev->dev.of_node,"dma-ranges" ,NULL )) -dma_set_mask_and_coherent (&pdev->dev,DMA_BIT_MASK (34 )); - ret =video_register_device (jpeg->vdev,VFL_TYPE_VIDEO ,-1 );if (ret) {v4l2_err (&jpeg->v4l2_dev,"Failed to register video device\n" );
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 11/14 media: mediatek: vcodec: Remove the setting for dma_mask
In reply to Yong WuIn order to simplify the masters to set their respective dma masks, MTK IOMMU helps to centralize the processing. Because all the dma ranges is set in IOMMU, IOMMU knows well the dma mask requirements of masters. After this patch, the masters(codec here) code does not need care dma-ranges/dma_mask related information.
--- .../media/platform/mediatek/vcodec/mtk_vcodec_dec_drv.c | 8 -------- .../media/platform/mediatek/vcodec/mtk_vcodec_enc_drv.c | 3 --- 2 files changed, 11 deletions(-)
drivers/media/platform/mediatek/vcodec/mtk_vcodec_dec_drv.c +0 -8
@@ -321,14 +321,6 @@ static int mtk_vcodec_probe(struct platform_device *pdev) } } -if (of_get_property (pdev->dev.of_node,"dma-ranges" ,NULL )) { - ret =dma_set_mask_and_coherent (&pdev->dev,DMA_BIT_MASK (34 )); -if (ret) { -mtk_v4l2_err ("Failed to set mask" ); - goto err_core_workq; - } - } -for (i =0 ; i <MTK_VDEC_HW_MAX ; i++)mutex_init (&dev->dec_mutex[i]);mutex_init (&dev->dev_mutex);
drivers/media/platform/mediatek/vcodec/mtk_vcodec_enc_drv.c +0 -3
@@ -344,9 +344,6 @@ static int mtk_vcodec_probe(struct platform_device *pdev) goto err_event_workq; } -if (of_get_property (pdev->dev.of_node,"dma-ranges" ,NULL )) -dma_set_mask_and_coherent (&pdev->dev,DMA_BIT_MASK (34 )); - ret =video_register_device (vfd_enc,VFL_TYPE_VIDEO ,-1 );if (ret) {mtk_v4l2_err ("Failed to register video device" );
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 12/14 arm64: dts: mt8195: Remove the unnecessary dma-ranges
In reply to Yong WuAfter we add the dma-ranges in the parent "soc" node, this property is unnecessary for the leaf node.
--- arch/arm64/boot/dts/mediatek/mt8195.dtsi | 3 --- 1 file changed, 3 deletions(-)
arch/arm64/boot/dts/mediatek/mt8195.dtsi +0 -3
@@ -2299,7 +2299,6 @@ venc: video-codec@1a020000 { power-domains = <&spm MT8195_POWER_DOMAIN_VENC>; #address-cells = <2>; #size-cells = <2>; - dma-ranges = <0x1 0x0 0x0 0x40000000 0x0 0xfff00000>; }; jpgdec-master {
@@ -2311,7 +2310,6 @@ jpgdec-master { <&iommu_vdo M4U_PORT_L19_JPGDEC_BSDMA1>, <&iommu_vdo M4U_PORT_L19_JPGDEC_BUFF_OFFSET1>, <&iommu_vdo M4U_PORT_L19_JPGDEC_BUFF_OFFSET0>; - dma-ranges = <0x1 0x0 0x0 0x40000000 0x0 0xfff00000>; #address-cells = <2>; #size-cells = <2>; ranges;
@@ -2383,7 +2381,6 @@ jpgenc-master { <&iommu_vpp M4U_PORT_L20_JPGENC_C_RDMA>, <&iommu_vpp M4U_PORT_L20_JPGENC_Q_TABLE>, <&iommu_vpp M4U_PORT_L20_JPGENC_BSDMA>; - dma-ranges = <0x1 0x0 0x0 0x40000000 0x0 0xfff00000>; #address-cells = <2>; #size-cells = <2>; ranges;
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 13/14 arm64: dts: mt8195: Add dma-ranges for the parent "soc" node
In reply to Yong WuAfter commit f1ad5338a4d5 ("of: Fix "dma-ranges" handling for bus controllers"), the dma-ranges property is not allowed for the leaf node. But our iommu/dma-ranges is 16GB, we still expect separate the 16GB dma-range like:
a) display is in 0 - 4GB;
b) vcodec is in 4GB - 8GB;
c) camera is in 8GB - 12GB.
We can not expect all the masters add a parent node for them, especial for the existed drivers/nodes.
Thus, we add whole the 16GB dma-ranges in the parent "soc" node.
--- arch/arm64/boot/dts/mediatek/mt8195.dtsi | 1 + 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/mediatek/mt8195.dtsi +1 -0
@@ -364,6 +364,7 @@ soc { #size-cells = <2>; compatible = "simple-bus"; ranges; + dma-ranges = <0x0 0x0 0x0 0x0 0x4 0x0>; gic: interrupt-controller@c000000 { compatible = "arm,gic-v3";
Signature · 1 line
2.25.1
Yong Wu
maintainerPATCH v6 14/14 arm64: dts: mt8186: Add dma-ranges for the parent "soc" node
In reply to Yong WuPrepare for the MM nodes whose dma-ranges(iova range) is 16GB.
--- arch/arm64/boot/dts/mediatek/mt8186.dtsi | 1 + 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/mediatek/mt8186.dtsi +1 -0
@@ -324,6 +324,7 @@ soc { #address-cells = <2>; #size-cells = <2>; compatible = "simple-bus"; + dma-ranges = <0x0 0x0 0x0 0x0 0x4 0x0>; ranges; gic: interrupt-controller@c000000 {
Signature · 1 line
2.25.1