sunxi: boot0.h: allow RVBAR MMIO address customisation
Subsystems (3)
PATCH 1/2 sunxi: boot0.h: allow RVBAR MMIO address customisation
To switch the ARMv8 Allwinner SoCs into the 64-bit AArch64 ISA, we need to program the 64-bit start code address into an MMIO mapped register that shadows the architectural RVBAR register.
This address is SoC specific, with just two versions out there so far. Now a third address emerged, on a *variant* of an existing SoC (H616).
Change the boot0.h start code to make this address a Kconfig selectable option, to allow easier maintenance.
We make this address user-visible (even though it shouldn't be), to allow putting this in defconfig. This is needed because there are apparently revisions of the H616 SoC out there using different addresses, so this becomes a per-board decision.
--- arch/arm/include/asm/arch-sunxi/boot0.h | 7 ++----- arch/arm/mach-sunxi/Kconfig | 12 ++++++++++++ 2 files changed, 14 insertions(+), 5 deletions(-)
arch/arm/include/asm/arch-sunxi/boot0.h +2 -5
@@ -39,11 +39,8 @@ .word 0xf57ff06f // isb sy .word 0xe320f003 // wfi .word 0xeafffffd // b @wfi -#ifndef CONFIG_SUN50I_GEN_H6 - .word 0x017000a0 // writeable RVBAR mapping address -#else - .word 0x09010040 // writeable RVBAR mapping address -#endif + + .word CONFIG_SUNXI_RVBAR_ADDRESS // writable RVBAR mapping addr#ifdef CONFIG_SPL_BUILD .word CONFIG_SPL_TEXT_BASE#else
arch/arm/mach-sunxi/Kconfig +12 -0
@@ -110,6 +110,18 @@ config SUNXI_SRAM_ADDRESS Some newer SoCs map the boot ROM at address 0 instead and move the SRAM to a different address. +config SUNXI_RVBAR_ADDRESS + hex "RVBAR address" + depends on ARM64 + default 0x09010040 if SUN50I_GEN_H6 + default 0x017000a0 + ---help--- + The read-only RVBAR system register holds the address of the first + instruction to execute after a reset. Allwinner cores provide a + writable MMIO backing store for this register, to allow to set the + entry point when switching to AArch64. This store is on different + addresses, depending on the SoC. + config SUNXI_A64_TIMER_ERRATUM bool
Signature · 1 line
2.25.1
PATCH 2/2 sunxi: remove support for boot0 header reservation
In the early days of the Allwinner A64 U-Boot support, we relied on a vendor provided "boot0" binary to perform the DRAM initialisation. This replaced the SPL, and required to equip the U-Boot (proper) binary with a vendor specific header to be recognised as a valid boot0 payload. Fortunately these days are long gone (we gained SPL and DRAM support in early 2017!), and we never needed to use that hack on any later 64-bit Allwinner SoC.
Since this is highly obsolete by now, remove the Kconfig option and the small pieces of "code" associated with it.
Provide some comments about the purpose of the remaining boot0 code on the way.
--- arch/arm/include/asm/arch-sunxi/boot0.h | 18 +++++++++++------- arch/arm/mach-sunxi/Kconfig | 9 --------- configs/a64-olinuxino-emmc_defconfig | 1 - configs/a64-olinuxino_defconfig | 1 - configs/amarula_a64_relic_defconfig | 1 - configs/bananapi_m64_defconfig | 1 - configs/nanopi_a64_defconfig | 1 - configs/oceanic_5205_5inmfd_defconfig | 1 - configs/orangepi_win_defconfig | 1 - configs/pine64_plus_defconfig | 1 - configs/sopine_baseboard_defconfig | 1 - 11 files changed, 11 insertions(+), 25 deletions(-)
arch/arm/include/asm/arch-sunxi/boot0.h +11 -7
@@ -1,13 +1,17 @@/* SPDX-License-Identifier: GPL-2.0+ */ /* -* Configuration settings for the Allwinner A64 (sun50i) CPU +* Very early code for Allwinner 64-bit CPUs. +* +* The BROM runs entirely in AArch32 state, so the SPL is entered using this +* ISA. Depending on the rest of the firmware stack, this may also be true +* for U-Boot proper. +* Provide the "RMR reset into 64-bit" sequence, in AArch32 machine language, +* so that we can have all of U-Boot in AArch64. The first instruction is +* chosen so that if the CPU is already using AArch64, it will skip the code +* and jump straight to the reset vector. */ -#if defined(CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER ) && !defined(CONFIG_SPL_BUILD ) -/* reserve space for BOOT0 header information */ - b reset - .space 1532 -#elif defined(CONFIG_ARM_BOOT_HOOK_RMR ) +#ifdef CONFIG_ARM_BOOT_HOOK_RMR /* * Switch into AArch64 if needed. * Refer to arch/arm/mach-sunxi/rmr_switch.S for the original source.
@@ -47,7 +51,7 @@ .word CONFIG_TEXT_BASE #endif .word fel_stash - . -#else +#else /* !CONFIG_ARM_BOOT_HOOK_RMR */ /* normal execution */ b reset #endif
arch/arm/mach-sunxi/Kconfig +0 -9
@@ -386,15 +386,6 @@ config MACH_SUN8I default y if MACH_SUN8I_R40 default y if MACH_SUN8I_V3S -config RESERVE_ALLWINNER_BOOT0_HEADER - bool "reserve space for Allwinner boot0 header" - select ENABLE_ARM_SOC_BOOT0_HOOK - ---help--- - Prepend a 1536 byte (empty) header to the U-Boot image file, to be - filled with magic values post build. The Allwinner provided boot0 - blob relies on this information to load and execute U-Boot. - Only needed on 64-bit Allwinner boards so far when using boot0. - config ARM_BOOT_HOOK_RMR bool depends on ARM64
configs/a64-olinuxino-emmc_defconfig +0 -1
@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-olinuxino-emmc" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUPPORT_EMMC_BOOT=y
configs/a64-olinuxino_defconfig +0 -1
@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-olinuxino" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y
configs/amarula_a64_relic_defconfig +0 -1
@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-amarula-relic" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_VIDEO_DE2 is not set # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
configs/bananapi_m64_defconfig +0 -1
@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-bananapi-m64" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUPPORT_EMMC_BOOT=y
configs/nanopi_a64_defconfig +0 -1
@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-nanopi-a64" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y CONFIG_USB_EHCI_HCD=y
configs/oceanic_5205_5inmfd_defconfig +0 -1
@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-oceanic-5205-5inmfd" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_SUNXI_DRAM_LPDDR3_STOCK=y CONFIG_DRAM_CLK=552 CONFIG_DRAM_ZQ=3881949
configs/orangepi_win_defconfig +0 -1
@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-orangepi-win" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MACPWR="PD14" CONFIG_SPL_SPI_SUNXI=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
configs/pine64_plus_defconfig +0 -1
@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-pine64-plus" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_PINE64_DT_SELECTION=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_OF_LIST="sun50i-a64-pine64 sun50i-a64-pine64-plus"
configs/sopine_baseboard_defconfig +0 -1
@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-sopine-baseboard" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_SUNXI_DRAM_LPDDR3_STOCK=y CONFIG_DRAM_CLK=552 CONFIG_DRAM_ZQ=3881949
Signature · 1 line
2.25.1
Re: [PATCH 2/2] sunxi: remove support for boot0 header reservation
Dne sreda, 05. april 2023 ob 16:27:31 CEST je Andre Przywara napisal(a):
Quoted 8 lines
In the early days of the Allwinner A64 U-Boot support, we relied on a vendor provided "boot0" binary to perform the DRAM initialisation. This replaced the SPL, and required to equip the U-Boot (proper) binary with a vendor specific header to be recognised as a valid boot0 payload. Fortunately these days are long gone (we gained SPL and DRAM support in early 2017!), and we never needed to use that hack on any later 64-bit Allwinner SoC.
Quoted 7 lines
Since this is highly obsolete by now, remove the
Kconfigoption and the small pieces of "code" associated with it.Provide some comments about the purpose of the remaining boot0 code on the way.
Signed-off-by Andre Przywara <[email protected]>
I think it's time to remove this code too.
Best regards,
Jernej
Quoted 183 lines
--- arch/arm/include/asm/arch-sunxi/boot0.h | 18 +++++++++++------- arch/arm/mach-sunxi/Kconfig | 9 --------- configs/a64-olinuxino-emmc_defconfig | 1 - configs/a64-olinuxino_defconfig | 1 - configs/amarula_a64_relic_defconfig | 1 - configs/bananapi_m64_defconfig | 1 - configs/nanopi_a64_defconfig | 1 - configs/oceanic_5205_5inmfd_defconfig | 1 - configs/orangepi_win_defconfig | 1 - configs/pine64_plus_defconfig | 1 - configs/sopine_baseboard_defconfig | 1 - 11 files changed, 11 insertions(+), 25 deletions(-)(quoted diff) +0
-0
b/arch/arm/include/asm/arch-sunxi/boot0.hindex59ea75a96b5..1a396f78488100644arch/arm/include/asm/arch-sunxi/boot0.h +3
-1@@ -1,13 +1,17 @@/* SPDX-License-Identifier: GPL-2.0+ */ /* -* Configuration settings for the Allwinner A64 (sun50i) CPU +* Very early code for Allwinner 64-bit CPUs. +* +* The BROM runs entirely in AArch32 state, so the SPL is entered using this + * ISA. Depending on the rest of the firmware stack, this may also be true + * for U-Boot proper.
+ * Provide the "RMR reset into 64-bit" sequence, in AArch32 machine language, + * so that we can have all of U-Boot in AArch64. The first instruction is + * chosen so that if the CPU is already using AArch64, it will skip the code + * and jump straight to the reset vector. */-#if
defined(CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER)&& !defined(CONFIG_SPL_BUILD) -/* reserve space for BOOT0 header information */arch/arm/include/asm/arch-sunxi/boot0.h +2
-4- b reset - .space 1532 -#elif defined(CONFIG_ARM_BOOT_HOOK_RMR ) +#ifdef CONFIG_ARM_BOOT_HOOK_RMR /* * Switch into AArch64 if needed. * Refer to arch/arm/mach-sunxi/rmr_switch.S for the original source. @@ -47,7 +51,7 @@ .word CONFIG_TEXT_BASE #endif .word fel_stash - . -#else +#else /* !CONFIG_ARM_BOOT_HOOK_RMR */ /* normal execution */ b reset #endifarch/arm/mach-sunxi/Kconfig +0
-9@@ -386,15 +386,6 @@ config MACH_SUN8I default y if MACH_SUN8I_R40 default y if MACH_SUN8I_V3S -config RESERVE_ALLWINNER_BOOT0_HEADER - bool "reserve space for Allwinner boot0 header" - select ENABLE_ARM_SOC_BOOT0_HOOK - ---help--- - Prepend a 1536 byte (empty) header to the U-Boot image file, to be - filled with magic values post build. The Allwinner provided boot0 - blob relies on this information to load and execute U-Boot. - Only needed on 64-bit Allwinner boards so far when using boot0. - config ARM_BOOT_HOOK_RMR bool depends on ARM64(quoted diff) +0
-0b/configs/a64-olinuxino-emmc_defconfig index
8ec9eb3e9c2..a5989fab1c6100644configs/a64-olinuxino-emmc_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-olinuxino-emmc" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUPPORT_EMMC_BOOT=y(quoted diff) +0
-0b/configs/a64-olinuxino_defconfig index
16cef18beef..0b469c25d0d100644configs/a64-olinuxino_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-olinuxino" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y(quoted diff) +0
-0b/configs/amarula_a64_relic_defconfig index
ae44b66d109..292af6e372e100644configs/amarula_a64_relic_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-amarula-relic" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_VIDEO_DE2 is not set # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not setconfigs/bananapi_m64_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-bananapi-m64" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUPPORT_EMMC_BOOT=yconfigs/nanopi_a64_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-nanopi-a64" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y CONFIG_USB_EHCI_HCD=y(quoted diff) +0
-0b/configs/oceanic_5205_5inmfd_defconfig index
2ebca673808..6cdcf782bee100644configs/oceanic_5205_5inmfd_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-oceanic-5205-5inmfd" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_SUNXI_DRAM_LPDDR3_STOCK=y CONFIG_DRAM_CLK=552 CONFIG_DRAM_ZQ=3881949configs/orangepi_win_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-orangepi-win" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MACPWR="PD14" CONFIG_SPL_SPI_SUNXI=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not setconfigs/pine64_plus_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-pine64-plus" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_PINE64_DT_SELECTION=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_OF_LIST="sun50i-a64-pine64 sun50i-a64-pine64-plus"(quoted diff) +0
-0b/configs/sopine_baseboard_defconfig index
a5e1478c117..d9b0eb37c54100644configs/sopine_baseboard_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-sopine-baseboard" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_SUNXI_DRAM_LPDDR3_STOCK=y CONFIG_DRAM_CLK=552 CONFIG_DRAM_ZQ=3881949
Re: [PATCH 2/2] sunxi: remove support for boot0 header reservation
On Sat, 08 Apr 2023 08:19:16 +0200
Jernej Škrabec <[email protected]> wrote:
Hi,
Quoted 12 lines
Dne sreda, 05. april 2023 ob 16:27:31 CEST je Andre Przywara napisal(a):
Quoted 11 lines
In the early days of the Allwinner A64 U-Boot support, we relied on a vendor provided "boot0" binary to perform the DRAM initialisation. This replaced the SPL, and required to equip the U-Boot (proper) binary with a vendor specific header to be recognised as a valid boot0 payload. Fortunately these days are long gone (we gained SPL and DRAM support in early 2017!), and we never needed to use that hack on any later 64-bit Allwinner SoC.
Since this is highly obsolete by now, remove the
Kconfigoption and the small pieces of "code" associated with it.
Quoted 8 lines
Quoted 4 lines
Provide some comments about the purpose of the remaining boot0 code on the way.
Signed-off-by Andre Przywara <[email protected]>I think it's time to remove this code too.
Reviewed-by Jernej Skrabec <[email protected]>
Many thanks! So I kept the "code" in for now, to appease Piotr, but removed the symbols from the A64's defconfigs. I will propose that removal then again at a later time.
Queued for sunxi/master.
Cheers,
Andre
Quoted 189 lines
Quoted 184 lines
--- arch/arm/include/asm/arch-sunxi/boot0.h | 18 +++++++++++------- arch/arm/mach-sunxi/Kconfig | 9 --------- configs/a64-olinuxino-emmc_defconfig | 1 - configs/a64-olinuxino_defconfig | 1 - configs/amarula_a64_relic_defconfig | 1 - configs/bananapi_m64_defconfig | 1 - configs/nanopi_a64_defconfig | 1 - configs/oceanic_5205_5inmfd_defconfig | 1 - configs/orangepi_win_defconfig | 1 - configs/pine64_plus_defconfig | 1 - configs/sopine_baseboard_defconfig | 1 - 11 files changed, 11 insertions(+), 25 deletions(-)(quoted diff) +0
-0
b/arch/arm/include/asm/arch-sunxi/boot0.hindex59ea75a96b5..1a396f78488100644arch/arm/include/asm/arch-sunxi/boot0.h +3
-1@@ -1,13 +1,17 @@/* SPDX-License-Identifier: GPL-2.0+ */ /* -* Configuration settings for the Allwinner A64 (sun50i) CPU +* Very early code for Allwinner 64-bit CPUs. +* +* The BROM runs entirely in AArch32 state, so the SPL is entered using this + * ISA. Depending on the rest of the firmware stack, this may also be true + * for U-Boot proper.
+ * Provide the "RMR reset into 64-bit" sequence, in AArch32 machine language, + * so that we can have all of U-Boot in AArch64. The first instruction is + * chosen so that if the CPU is already using AArch64, it will skip the code + * and jump straight to the reset vector. */-#if
defined(CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER)&& !defined(CONFIG_SPL_BUILD) -/* reserve space for BOOT0 header information */arch/arm/include/asm/arch-sunxi/boot0.h +2
-4- b reset - .space 1532 -#elif defined(CONFIG_ARM_BOOT_HOOK_RMR ) +#ifdef CONFIG_ARM_BOOT_HOOK_RMR /* * Switch into AArch64 if needed. * Refer to arch/arm/mach-sunxi/rmr_switch.S for the original source. @@ -47,7 +51,7 @@ .word CONFIG_TEXT_BASE #endif .word fel_stash - . -#else +#else /* !CONFIG_ARM_BOOT_HOOK_RMR */ /* normal execution */ b reset #endifarch/arm/mach-sunxi/Kconfig +0
-9@@ -386,15 +386,6 @@ config MACH_SUN8I default y if MACH_SUN8I_R40 default y if MACH_SUN8I_V3S -config RESERVE_ALLWINNER_BOOT0_HEADER - bool "reserve space for Allwinner boot0 header" - select ENABLE_ARM_SOC_BOOT0_HOOK - ---help--- - Prepend a 1536 byte (empty) header to the U-Boot image file, to be - filled with magic values post build. The Allwinner provided boot0 - blob relies on this information to load and execute U-Boot. - Only needed on 64-bit Allwinner boards so far when using boot0. - config ARM_BOOT_HOOK_RMR bool depends on ARM64(quoted diff) +0
-0b/configs/a64-olinuxino-emmc_defconfig index
8ec9eb3e9c2..a5989fab1c6100644configs/a64-olinuxino-emmc_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-olinuxino-emmc" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUPPORT_EMMC_BOOT=y(quoted diff) +0
-0b/configs/a64-olinuxino_defconfig index
16cef18beef..0b469c25d0d100644configs/a64-olinuxino_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-olinuxino" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y(quoted diff) +0
-0b/configs/amarula_a64_relic_defconfig index
ae44b66d109..292af6e372e100644configs/amarula_a64_relic_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-amarula-relic" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_VIDEO_DE2 is not set # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not setconfigs/bananapi_m64_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-bananapi-m64" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUPPORT_EMMC_BOOT=yconfigs/nanopi_a64_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-nanopi-a64" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y CONFIG_USB_EHCI_HCD=y(quoted diff) +0
-0b/configs/oceanic_5205_5inmfd_defconfig index
2ebca673808..6cdcf782bee100644configs/oceanic_5205_5inmfd_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-oceanic-5205-5inmfd" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_SUNXI_DRAM_LPDDR3_STOCK=y CONFIG_DRAM_CLK=552 CONFIG_DRAM_ZQ=3881949configs/orangepi_win_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-orangepi-win" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_MACPWR="PD14" CONFIG_SPL_SPI_SUNXI=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not setconfigs/pine64_plus_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-pine64-plus" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_PINE64_DT_SELECTION=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_OF_LIST="sun50i-a64-pine64 sun50i-a64-pine64-plus"(quoted diff) +0
-0b/configs/sopine_baseboard_defconfig index
a5e1478c117..d9b0eb37c54100644configs/sopine_baseboard_defconfig +0
-1@@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-sopine-baseboard" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_SUNXI_DRAM_LPDDR3_STOCK=y CONFIG_DRAM_CLK=552 CONFIG_DRAM_ZQ=3881949
Dne sreda, 05. april 2023 ob 16:27:30 CEST je Andre Przywara napisal(a):
Quoted 6 lines
To switch the ARMv8 Allwinner SoCs into the 64-bit AArch64 ISA, we need to program the 64-bit start code address into an MMIO mapped register that shadows the architectural RVBAR register.
This address is SoC specific, with just two versions out there so far. Now a third address emerged, on a *variant* of an existing SoC (H616).
Quoted 8 lines
Change the
boot0.hstart code to make this address aKconfigselectable option, to allow easier maintenance.
We make this address user-visible (even though it shouldn't be), to allow putting this in defconfig. This is needed because there are apparently revisions of the H616 SoC out there using different addresses, so this becomes a per-board decision.Signed-off-by Andre Przywara <[email protected]>
Best regards,
Jernej
Quoted 11 lines
--- arch/arm/include/asm/arch-sunxi/boot0.h | 7 ++----- arch/arm/mach-sunxi/Kconfig | 12 ++++++++++++ 2 files changed, 14 insertions(+), 5 deletions(-)(quoted diff) +0
-0
b/arch/arm/include/asm/arch-sunxi/boot0.hindex46b7e073b59..59ea75a96b5100644
arch/arm/include/asm/arch-sunxi/boot0.h line 43
Quoted 10 lines
arch/arm/include/asm/arch-sunxi/boot0.h +2
-5@@ -39,11 +39,8 @@ .word 0xf57ff06f // isb sy .word 0xe320f003 // wfi .word 0xeafffffd // b @wfi -#ifndef CONFIG_SUN50I_GEN_H6 - .word 0x017000a0 // writeable RVBAR mapping address -#else - .word 0x09010040 // writeable RVBAR mapping address -#endif + + .word CONFIG_SUNXI_RVBAR_ADDRESS // writable RVBAR mapping
addr
Quoted 25 lines
arch/arm/include/asm/arch-sunxi/boot0.h +0
-0#ifdef CONFIG_SPL_BUILD .word CONFIG_SPL_TEXT_BASE#else arch/arm/mach-sunxi/Kconfig +12
-0@@ -110,6 +110,18 @@ config SUNXI_SRAM_ADDRESS Some newer SoCs map the boot ROM at address 0 instead and move the SRAM to a different address. +config SUNXI_RVBAR_ADDRESS + hex "RVBAR address" + depends on ARM64 + default 0x09010040 if SUN50I_GEN_H6 + default 0x017000a0 + ---help--- + The read-only RVBAR system register holds the address of the first + instruction to execute after a reset. Allwinner cores provide a + writable MMIO backing store for this register, to allow to set the + entry point when switching to AArch64. This store is on different + addresses, depending on the SoC. + config SUNXI_A64_TIMER_ERRATUM bool