Skip to contentSkip to conversation

arm: mach-k3: Workaround errata ID i2331

PATCH In review Vignesh Raghavendra 3 participants 3 messages Apr 6, 2023 – May 3, 2023

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm: mach-k3: Workaround errata ID i2331

From: Nitin Yadav <[email protected]>

Errata doc: https://www.ti.com/lit/pdf/sprz457
Errata ID i2331 CPSW: Device lockup when reading CPSW registers

Details: A device lockup can occur during the second read of any CPSW subsystem register after any MAIN domain power on reset (POR). A MAIN domain POR occurs using the hardware MCU_PORz signal, or via software using CTRLMMR_RST_CTRL.SW_MAIN_POR or CTRLMMR_MCU_RST_CTRL.SW_MAIN_POR. After these resets, the processor and internal bus structures may get into a state which is only recoverable with full device reset using MCU_PORz.
Due to this errata, Ethernet boot should not be used on this device.

Workaround(s): To avoid the lockup, a warm reset should be issued after a MAIN domain POR and before any access to the CPSW registers. The warm reset realigns internal clocks and prevents the lockup from happening. Workaround above errata by calling do_reset() in case of cold boot in order to trigger warm reset. This needs enabling SYSRESET driver in R5 SPL to enable TI SCI reset driver.

---
 arch/arm/mach-k3/am642_init.c  | 33 +++++++++++++++++++++++++++++++++
 configs/am64x_evm_r5_defconfig |  3 +++
 2 files changed, 36 insertions(+)
arch/arm/mach-k3/am642_init.c +33 -0
index 1bf7e163cc46..093a68b63077 100644
@@ -22,9 +22,15 @@
 #include <dm/pinctrl.h>
 #include <mmc.h>
 #include <dm/root.h>
+#include <command.h>
 
 #define CTRLMMR_MCU_RST_CTRL			0x04518170
 
+#define CTRLMMR_MCU_RST_SRC                    (MCU_CTRL_MMR0_BASE + 0x18178)
+#define COLD_BOOT                              0
+#define SW_POR_MCU                             BIT(24)
+#define SW_POR_MAIN                            BIT(25)
+
 static void ctrl_mmr_unlock(void)
 {
 	/* Unlock all PADCFG_MMR1 module registers */
@@ -166,6 +172,7 @@ void board_init_f(ulong dummy)
 #if defined(CONFIG_K3_LOAD_SYSFW) || defined(CONFIG_K3_AM64_DDRSS) || defined(CONFIG_ESM_K3)
 	struct udevice *dev;
 	int ret;
+	int rst_src;
 #endif
 
 #if defined(CONFIG_CPU_V7R)
@@ -210,6 +217,32 @@ void board_init_f(ulong dummy)
 			k3_mmc_restart_clock);
 #endif
 
+#if defined(CONFIG_CPU_V7R)
+	/*
+	 * Errata ID i2331 CPSW: A device lockup can occur during the second
+	 * read of any CPSW subsystem register after any MAIN domain power on
+	 * reset (POR). A MAIN domain POR occurs using the hardware MCU_PORz
+	 * signal, or via software using CTRLMMR_RST_CTRL.SW_MAIN_POR or
+	 * CTRLMMR_MCU_RST_CTRL.SW_MAIN_POR. After these resets, the processor
+	 * and internal bus structures may get into a state which is only
+	 * recoverable with full device reset using MCU_PORz.
+	 * Workaround(s): To avoid the lockup, a warm reset should be issued
+	 * after a MAIN domain POR and before any access to the CPSW registers.
+	 * The warm reset realigns internal clocks and prevents the lockup from
+	 * happening.
+	 */
+	ret = uclass_first_device_err(UCLASS_SYSRESET, &dev);
+	if (ret)
+		printf("\n%s:uclass device error [%d]\n",__func__,ret);
+
+	rst_src = readl(CTRLMMR_MCU_RST_SRC);
+	if (rst_src == COLD_BOOT || rst_src & (SW_POR_MCU | SW_POR_MAIN)) {
+		printf("Resetting on cold boot to workaround ErrataID:i2331\n");
+		printf("Please resend tiboot3.bin in case of UART/DFU boot\n");
+		do_reset(NULL, 0, 0, NULL);
+	}
+#endif
+
 	/* Output System Firmware version info */
 	k3_sysfw_print_ver();
 
configs/am64x_evm_r5_defconfig +3 -0
index b75cae6d803e..bb705a1c3ce2 100644
@@ -169,3 +169,6 @@ CONFIG_USB_GADGET_VENDOR_NUM=0x0451
 CONFIG_USB_GADGET_PRODUCT_NUM=0x6165
 CONFIG_USB_GADGET_DOWNLOAD=y
 CONFIG_FS_FAT_MAX_CLUSTSIZE=16384
+CONFIG_SYSRESET=y
+CONFIG_SPL_SYSRESET=y
+CONFIG_SYSRESET_TI_SCI=y
Signature · 1 line
2.40.0
Reviewed-by on v1 1/1
#1 lore raw

Hi Vignesh!

On April 6, 2023 thus sayeth Vignesh Raghavendra:

Quoted 21 lines

From: Nitin Yadav <[email protected]>

Errata doc: https://www.ti.com/lit/pdf/sprz457
Errata ID i2331 CPSW: Device lockup when reading CPSW registers

Details: A device lockup can occur during the second read of any CPSW subsystem register after any MAIN domain power on reset (POR). A MAIN domain POR occurs using the hardware MCU_PORz signal, or via software using CTRLMMR_RST_CTRL.SW_MAIN_POR or CTRLMMR_MCU_RST_CTRL.SW_MAIN_POR. After these resets, the processor and internal bus structures may get into a state which is only recoverable with full device reset using MCU_PORz.
Due to this errata, Ethernet boot should not be used on this device.

Workaround(s): To avoid the lockup, a warm reset should be issued after a MAIN domain POR and before any access to the CPSW registers. The warm reset realigns internal clocks and prevents the lockup from happening. Workaround above errata by calling do_reset() in case of cold boot in order to trigger warm reset. This needs enabling SYSRESET driver in R5 SPL to enable TI SCI reset driver.

Quoted 7 lines
---
 arch/arm/mach-k3/am642_init.c  | 33 +++++++++++++++++++++++++++++++++
 configs/am64x_evm_r5_defconfig |  3 +++
 2 files changed, 36 insertions(+)

Thanks for sending this!

~Bryan

#2 lore raw
In reply to Vignesh Raghavendra
Quoted 21 lines · Vignesh Raghavendra

From: Nitin Yadav <[email protected]>

Errata doc: https://www.ti.com/lit/pdf/sprz457
Errata ID i2331 CPSW: Device lockup when reading CPSW registers

Details: A device lockup can occur during the second read of any CPSW subsystem register after any MAIN domain power on reset (POR). A MAIN domain POR occurs using the hardware MCU_PORz signal, or via software using CTRLMMR_RST_CTRL.SW_MAIN_POR or CTRLMMR_MCU_RST_CTRL.SW_MAIN_POR. After these resets, the processor and internal bus structures may get into a state which is only recoverable with full device reset using MCU_PORz.
Due to this errata, Ethernet boot should not be used on this device.

Workaround(s): To avoid the lockup, a warm reset should be issued after a MAIN domain POR and before any access to the CPSW registers. The warm reset realigns internal clocks and prevents the lockup from happening. Workaround above errata by calling do_reset() in case of cold boot in order to trigger warm reset. This needs enabling SYSRESET driver in R5 SPL to enable TI SCI reset driver.

Quoted 3 lines

Applied to u-boot/master, thanks!

Signature · 1 line
Tom