arm64: qcom: add PMIC regulators for sa8775p
Subsystems (4)
cover arm64: qcom: add PMIC regulators for sa8775p
From: Bartosz Golaszewski <[email protected]>
Here are the remaining patches from the big PMIC series that add the DT bindings for RPMH regulators for SA8775P platforms, implement relevant support in the driver and add the regulator nodes to the sa8775p-ride board .dts.
Since the first submission:
- the DT bindings now contain the missing supply properties
- the ldo8 min voltage has been increased
Bartosz Golaszewski (3):
dt-bindings: regulator: qcom,rpmh: add compatible for pmm8654au RPMH
regulator: qcom-rpmh: add support for pmm8654au regulators
arm64: dts: qcom: sa8775p-ride: add PMIC regulators
.../regulator/qcom,rpmh-regulator.yaml | 17 ++ arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 233 ++++++++++++++++++ drivers/regulator/qcom-rpmh-regulator.c | 55 +++++ 3 files changed, 305 insertions(+)
Signature · 1 line
2.37.2
PATCH 1/3 dt-bindings: regulator: qcom,rpmh: add compatible for pmm8654au RPMH
From: Bartosz Golaszewski <[email protected]>
Add the compatible for the pmm8654au RPMH regulators present on the sa8775p-ride development board.
Signed-off-by Bartosz Golaszewski <[email protected]>
--- .../bindings/regulator/qcom,rpmh-regulator.yaml | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml +17 -0
@@ -80,6 +80,7 @@ properties: - qcom,pmg1110-rpmh-regulators - qcom,pmi8998-rpmh-regulators - qcom,pmm8155au-rpmh-regulators + - qcom,pmm8654au-rpmh-regulators - qcom,pmr735a-rpmh-regulators - qcom,pmx55-rpmh-regulators - qcom,pmx65-rpmh-regulators
@@ -247,6 +248,22 @@ allOf: patternProperties: "^vdd-s([1-9]|10)-supply$": true + - if: + properties: + compatible: + enum: + - qcom,pmm8654au-rpmh-regulators + then: + properties: + vdd-l1-supply: true + vdd-l2-l3-supply: true + vdd-l4-supply: true + vdd-l5-supply: true + vdd-l6-l7-supply: true + vdd-l8-l9-supply: true + patternProperties: + "^vdd-s[1-9]-supply$": true + - if: properties: compatible:
Signature · 1 line
2.37.2
Re: [PATCH 1/3] dt-bindings: regulator: qcom,rpmh: add compatible for pmm8654au RPMH
Quoted 4 lines · Bartosz Golaszewski
From: Bartosz Golaszewski <[email protected]>
Add the compatible for the pmm8654au RPMH regulators present on the sa8775p-ride development board.
Reviewed-by Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof
PATCH 2/3 regulator: qcom-rpmh: add support for pmm8654au regulators
In reply to Bartosz GolaszewskiFrom: Bartosz Golaszewski <[email protected]>
Add the RPMH regulators exposed by the PMM8654au PMIC and its variants.
Signed-off-by Bartosz Golaszewski <[email protected]>
Reviewed-by Konrad Dybcio <[email protected]>
--- drivers/regulator/qcom-rpmh-regulator.c | 55 +++++++++++++++++++++++++ 1 file changed, 55 insertions(+)
drivers/regulator/qcom-rpmh-regulator.c +55 -0
@@ -694,6 +694,16 @@ static const struct rpmh_vreg_hw_data pmic5_pldo_lv = { .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode, }; +static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = { + .regulator_type =VRM , + .ops = &rpmh_regulator_vrm_drms_ops, + .voltage_range =REGULATOR_LINEAR_RANGE (1800000 ,0 ,187 ,8000 ), + .n_voltages =188 , + .hpm_min_load_uA =10000 , + .pmic_mode_map = pmic_mode_map_pmic5_ldo, + .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode, +}; +static const struct rpmh_vreg_hw_data pmic5_nldo = { .regulator_type =VRM , .ops = &rpmh_regulator_vrm_drms_ops,
@@ -704,6 +714,16 @@ static const struct rpmh_vreg_hw_data pmic5_nldo = { .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode, }; +static const struct rpmh_vreg_hw_data pmic5_nldo515 = { + .regulator_type =VRM , + .ops = &rpmh_regulator_vrm_drms_ops, + .voltage_range =REGULATOR_LINEAR_RANGE (320000 ,0 ,210 ,8000 ), + .n_voltages =211 , + .hpm_min_load_uA =30000 , + .pmic_mode_map = pmic_mode_map_pmic5_ldo, + .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode, +}; +static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = { .regulator_type =VRM , .ops = &rpmh_regulator_vrm_ops,
@@ -749,6 +769,15 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps525_mv = { .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode, }; +static const struct rpmh_vreg_hw_data pmic5_ftsmps527 = { + .regulator_type =VRM , + .ops = &rpmh_regulator_vrm_ops, + .voltage_range =REGULATOR_LINEAR_RANGE (320000 ,0 ,215 ,8000 ), + .n_voltages =215 , + .pmic_mode_map = pmic_mode_map_pmic5_smps, + .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode, +}; +static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = { .regulator_type =VRM , .ops = &rpmh_regulator_vrm_ops,
@@ -937,6 +966,28 @@ static const struct rpmh_vreg_init_data pmm8155au_vreg_data[] = { {} }; +static const struct rpmh_vreg_init_data pmm8654au_vreg_data[] = { +RPMH_VREG ("smps1" ,"smp%s1" , &pmic5_ftsmps527,"vdd-s1" ), +RPMH_VREG ("smps2" ,"smp%s2" , &pmic5_ftsmps527,"vdd-s2" ), +RPMH_VREG ("smps3" ,"smp%s3" , &pmic5_ftsmps527,"vdd-s3" ), +RPMH_VREG ("smps4" ,"smp%s4" , &pmic5_ftsmps527,"vdd-s4" ), +RPMH_VREG ("smps5" ,"smp%s5" , &pmic5_ftsmps527,"vdd-s5" ), +RPMH_VREG ("smps6" ,"smp%s6" , &pmic5_ftsmps527,"vdd-s6" ), +RPMH_VREG ("smps7" ,"smp%s7" , &pmic5_ftsmps527,"vdd-s7" ), +RPMH_VREG ("smps8" ,"smp%s8" , &pmic5_ftsmps527,"vdd-s8" ), +RPMH_VREG ("smps9" ,"smp%s9" , &pmic5_ftsmps527,"vdd-s9" ), +RPMH_VREG ("ldo1" ,"ldo%s1" , &pmic5_nldo515,"vdd-s9" ), +RPMH_VREG ("ldo2" ,"ldo%s2" , &pmic5_nldo515,"vdd-l2-l3" ), +RPMH_VREG ("ldo3" ,"ldo%s3" , &pmic5_nldo515,"vdd-l2-l3" ), +RPMH_VREG ("ldo4" ,"ldo%s4" , &pmic5_nldo515,"vdd-s9" ), +RPMH_VREG ("ldo5" ,"ldo%s5" , &pmic5_nldo515,"vdd-s9" ), +RPMH_VREG ("ldo6" ,"ldo%s6" , &pmic5_nldo515,"vdd-l6-l7" ), +RPMH_VREG ("ldo7" ,"ldo%s7" , &pmic5_nldo515,"vdd-l6-l7" ), +RPMH_VREG ("ldo8" ,"ldo%s8" , &pmic5_pldo515_mv,"vdd-l8-l9" ), +RPMH_VREG ("ldo9" ,"ldo%s9" , &pmic5_pldo,"vdd-l8-l9" ), + {} +}; +static const struct rpmh_vreg_init_data pm8350_vreg_data[] = {RPMH_VREG ("smps1" ,"smp%s1" , &pmic5_ftsmps510,"vdd-s1" ),RPMH_VREG ("smps2" ,"smp%s2" , &pmic5_ftsmps510,"vdd-s2" ),
@@ -1431,6 +1482,10 @@ static const struct of_device_id __maybe_unused rpmh_regulator_match_table[] = { .compatible = "qcom,pmm8155au-rpmh-regulators", .data = pmm8155au_vreg_data, }, + { + .compatible = "qcom,pmm8654au-rpmh-regulators", + .data = pmm8654au_vreg_data, + }, { .compatible = "qcom,pmx55-rpmh-regulators", .data = pmx55_vreg_data,
Signature · 1 line
2.37.2
PATCH 3/3 arm64: dts: qcom: sa8775p-ride: add PMIC regulators
In reply to Bartosz GolaszewskiFrom: Bartosz Golaszewski <[email protected]>
Add PMIC regulators for sa8775p-ride.
Signed-off-by Bartosz Golaszewski <[email protected]>
--- arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 233 ++++++++++++++++++++++ 1 file changed, 233 insertions(+)
arch/arm64/boot/dts/qcom/sa8775p-ride.dts +233 -0
@@ -5,6 +5,8 @@ /dts-v1/; +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + #include "sa8775p.dtsi" #include "sa8775p-pmics.dtsi"
@@ -25,6 +27,237 @@ chosen { }; }; +&apps_rsc { + regulators-0 { + compatible = "qcom,pmm8654au-rpmh-regulators"; + qcom,pmic-id = "a"; + + vreg_s4a: smps4 { + regulator-name = "vreg_s4a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1816000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s5a: smps5 { + regulator-name = "vreg_s5a"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <1996000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s9a: smps9 { + regulator-name = "vreg_s9a"; + regulator-min-microvolt = <535000>; + regulator-max-microvolt = <1120000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4a: ldo4 { + regulator-name = "vreg_l4a"; + regulator-min-microvolt = <788000>; + regulator-max-microvolt = <1050000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5a: ldo5 { + regulator-name = "vreg_l5a"; + regulator-min-microvolt = <870000>; + regulator-max-microvolt = <950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6a: ldo6 { + regulator-name = "vreg_l6a"; + regulator-min-microvolt = <870000>; + regulator-max-microvolt = <970000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a: ldo7 { + regulator-name = "vreg_l7a"; + regulator-min-microvolt = <720000>; + regulator-max-microvolt = <950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8a: ldo8 { + regulator-name = "vreg_l8a"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9a: ldo9 { + regulator-name = "vreg_l9a"; + regulator-min-microvolt = <2970000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pmm8654au-rpmh-regulators"; + qcom,pmic-id = "c"; + + vreg_l1c: ldo1 { + regulator-name = "vreg_l1c"; + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1260000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c: ldo2 { + regulator-name = "vreg_l2c"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c: ldo3 { + regulator-name = "vreg_l3c"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4c: ldo4 { + regulator-name = "vreg_l4c"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + /* + * FIXME: This should have regulator-allow-set-load but + * we're getting an over-current fault from the PMIC + * when switching to LPM. + */ + }; + + vreg_l5c: ldo5 { + regulator-name = "vreg_l5c"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6c: ldo6 { + regulator-name = "vreg_l6c"; + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <1980000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c: ldo7 { + regulator-name = "vreg_l7c"; + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8c: ldo8 { + regulator-name = "vreg_l8c"; + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c: ldo9 { + regulator-name = "vreg_l9c"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <2700000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pmm8654au-rpmh-regulators"; + qcom,pmic-id = "e"; + + vreg_s4e: smps4 { + regulator-name = "vreg_s4e"; + regulator-min-microvolt = <970000>; + regulator-max-microvolt = <1520000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s7e: smps7 { + regulator-name = "vreg_s7e"; + regulator-min-microvolt = <1010000>; + regulator-max-microvolt = <1170000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s9e: smps9 { + regulator-name = "vreg_s9e"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <570000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6e: ldo6 { + regulator-name = "vreg_l6e"; + regulator-min-microvolt = <1280000>; + regulator-max-microvolt = <1450000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8e: ldo8 { + regulator-name = "vreg_l8e"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + &i2c18 { clock-frequency = <400000>; pinctrl-0 = <&qup_i2c18_default>;
Signature · 1 line
2.37.2
Re: [PATCH 3/3] arm64: dts: qcom: sa8775p-ride: add PMIC regulators
Quoted 6 lines · Bartosz Golaszewski
From: Bartosz Golaszewski <[email protected]>
Add PMIC regulators for sa8775p-ride.
Signed-off-by Bartosz Golaszewski <[email protected]>---
Reviewed-by Konrad Dybcio <[email protected]>
Konrad
Quoted 254 lines
arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 233 ++++++++++++++++++++++ 1 file changed, 233 insertions(+)arch/arm64/boot/dts/qcom/sa8775p-ride.dts +233
-0@@ -5,6 +5,8 @@ /dts-v1/; +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + #include "sa8775p.dtsi" #include "sa8775p-pmics.dtsi"@@ -25,6 +27,237 @@ chosen { }; }; +&apps_rsc { + regulators-0 { + compatible = "qcom,pmm8654au-rpmh-regulators"; + qcom,pmic-id = "a"; + + vreg_s4a: smps4 { + regulator-name = "vreg_s4a"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1816000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s5a: smps5 { + regulator-name = "vreg_s5a"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <1996000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s9a: smps9 { + regulator-name = "vreg_s9a"; + regulator-min-microvolt = <535000>; + regulator-max-microvolt = <1120000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4a: ldo4 { + regulator-name = "vreg_l4a"; + regulator-min-microvolt = <788000>; + regulator-max-microvolt = <1050000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5a: ldo5 { + regulator-name = "vreg_l5a"; + regulator-min-microvolt = <870000>; + regulator-max-microvolt = <950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6a: ldo6 { + regulator-name = "vreg_l6a"; + regulator-min-microvolt = <870000>; + regulator-max-microvolt = <970000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7a: ldo7 { + regulator-name = "vreg_l7a"; + regulator-min-microvolt = <720000>; + regulator-max-microvolt = <950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8a: ldo8 { + regulator-name = "vreg_l8a"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9a: ldo9 { + regulator-name = "vreg_l9a"; + regulator-min-microvolt = <2970000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pmm8654au-rpmh-regulators"; + qcom,pmic-id = "c"; + + vreg_l1c: ldo1 { + regulator-name = "vreg_l1c"; + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1260000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c: ldo2 { + regulator-name = "vreg_l2c"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c: ldo3 { + regulator-name = "vreg_l3c"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4c: ldo4 { + regulator-name = "vreg_l4c"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + /* + * FIXME: This should have regulator-allow-set-load but + * we're getting an over-current fault from the PMIC + * when switching to LPM. + */ + }; + + vreg_l5c: ldo5 { + regulator-name = "vreg_l5c"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6c: ldo6 { + regulator-name = "vreg_l6c"; + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <1980000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c: ldo7 { + regulator-name = "vreg_l7c"; + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8c: ldo8 { + regulator-name = "vreg_l8c"; + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c: ldo9 { + regulator-name = "vreg_l9c"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <2700000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pmm8654au-rpmh-regulators"; + qcom,pmic-id = "e"; + + vreg_s4e: smps4 { + regulator-name = "vreg_s4e"; + regulator-min-microvolt = <970000>; + regulator-max-microvolt = <1520000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s7e: smps7 { + regulator-name = "vreg_s7e"; + regulator-min-microvolt = <1010000>; + regulator-max-microvolt = <1170000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s9e: smps9 { + regulator-name = "vreg_s9e"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <570000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6e: ldo6 { + regulator-name = "vreg_l6e"; + regulator-min-microvolt = <1280000>; + regulator-max-microvolt = <1450000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8e: ldo8 { + regulator-name = "vreg_l8e"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + &i2c18 { clock-frequency = <400000>; pinctrl-0 = <&qup_i2c18_default>;
Mark Brown
maintainerRe: (subset) [PATCH 0/3] arm64: qcom: add PMIC regulators for sa8775p
In reply to Bartosz GolaszewskiQuoted 10 lines · Bartosz Golaszewski
Here are the remaining patches from the big PMIC series that add the DT bindings for RPMH regulators for SA8775P platforms, implement relevant support in the driver and add the regulator nodes to the sa8775p-ride board .dts.
Since the first submission:
- the DT bindings now contain the missing supply properties
- the ldo8 min voltage has been increased[...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next
Thanks!
[1/3] dt-bindings: regulator: qcom,rpmh: add compatible for pmm8654au RPMH
commit: ba0887a6b94ea7f77df1e464aeca45758b4d92c3
[2/3] regulator: qcom-rpmh: add support for pmm8654au regulators
commit: 65f1b1dc0cc90236ed9be3970f4a763e853f3aabAll being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
Re: (subset) [PATCH 0/3] arm64: qcom: add PMIC regulators for sa8775p
In reply to Bartosz GolaszewskiQuoted 8 lines · Bartosz Golaszewski
From: Bartosz Golaszewski <[email protected]>
Here are the remaining patches from the big PMIC series that add the DT bindings for RPMH regulators for SA8775P platforms, implement relevant support in the driver and add the regulator nodes to the sa8775p-ride board .dts.
[...]
Applied, thanks!
[3/3] arm64: dts: qcom: sa8775p-ride: add PMIC regulators
commit: 27eba11291b0f9a8e9ca1f50ba0f6fd3fdda486b
Best regards,
Signature · 1 line
Bjorn Andersson <[email protected]>