MSM8953 remoteprocs dt bringup
cover MSM8953 remoteprocs dt bringup
This patch series introduce nodes required for bringing remoteproc cores.
Adam Skladowski (3):
arm64: dts: MSM8953: Add wcnss nodes
arm64: dts: MSM8953: Add mpss nodes
arm64: dts: MSM8953: Add lpass nodes
arch/arm64/boot/dts/qcom/msm8953.dtsi | 358 ++++++++++++++++++++++++++ 1 file changed, 358 insertions(+)
Signature · 1 line
2.25.1
PATCH 1/3 arm64: dts: MSM8953: Add wcnss nodes
Add nodes for remoteproc, smp2p and smsm to make it possible to use wifi/bt functionality on this platform.
--- arch/arm64/boot/dts/qcom/msm8953.dtsi | 130 ++++++++++++++++++++++++++ 1 file changed, 130 insertions(+)
arch/arm64/boot/dts/qcom/msm8953.dtsi +130 -0
@@ -326,6 +326,31 @@ rpmpd_opp_turbo: opp9 { }; }; + smp2p-wcnss { + compatible = "qcom,smp2p"; + qcom,smem = <451>, <431>; + + interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>; + + qcom,ipc = <&apcs 8 18>; + + qcom,local-pid = <0>; + qcom,remote-pid = <4>; + + smp2p_wcnss_out: master-kernel { + qcom,entry-name = "master-kernel"; + + #qcom,smem-state-cells = <1>; + }; + + smp2p_wcnss_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + smsm { compatible = "qcom,smsm";
@@ -340,6 +365,14 @@ apps_smsm: apps@0 { #qcom,smem-state-cells = <1>; }; + + wcnss_smsm: wcnss@6 { + reg = <6>; + interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <2>; + }; }; soc: soc@0 {
@@ -630,6 +663,37 @@ i2c_8_sleep: i2c-8-sleep-state { drive-strength = <2>; bias-disable; }; + + wcnss_pin_a: wcnss-active-state { + + wcss-wlan2-pins { + pins = "gpio76"; + function = "wcss_wlan2"; + drive-strength = <6>; + bias-pull-up; + }; + + wcss-wlan1-pins { + pins = "gpio77"; + function = "wcss_wlan1"; + drive-strength = <6>; + bias-pull-up; + }; + + wcss-wlan0-pins { + pins = "gpio78"; + function = "wcss_wlan0"; + drive-strength = <6>; + bias-pull-up; + }; + + wcss-wlan-pins { + pins = "gpio79", "gpio80"; + function = "wcss_wlan"; + drive-strength = <6>; + bias-pull-up; + }; + }; }; gcc: clock-controller@1800000 {
@@ -1245,6 +1309,72 @@ i2c_8: i2c@7af8000 { status = "disabled"; }; + wcnss: remoteproc@a21b000 { + compatible = "qcom,pronto-v3-pil", "qcom,pronto"; + reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000 0x3000>; + reg-names = "ccu", "dxe", "pmu"; + + memory-region = <&wcnss_fw_mem>; + + interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>, + <&smp2p_wcnss_in 0 IRQ_TYPE_EDGE_RISING>, + <&smp2p_wcnss_in 1 IRQ_TYPE_EDGE_RISING>, + <&smp2p_wcnss_in 2 IRQ_TYPE_EDGE_RISING>, + <&smp2p_wcnss_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack"; + + power-domains = <&rpmpd MSM8953_VDDCX>, + <&rpmpd MSM8953_VDDMX>; + power-domain-names = "cx", "mx"; + + qcom,smem-states = <&smp2p_wcnss_out 0>; + qcom,smem-state-names = "stop"; + + pinctrl-names = "default"; + pinctrl-0 = <&wcnss_pin_a>; + + status = "disabled"; + + wcnss_iris: iris { + /* Separate chip, compatible is board-specific */ + clocks = <&rpmcc RPM_SMD_RF_CLK2>; + clock-names = "xo"; + }; + + smd-edge { + interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>; + + qcom,ipc = <&apcs 8 17>; + qcom,smd-edge = <6>; + qcom,remote-pid = <4>; + + label = "pronto"; + + wcnss_ctrl: wcnss { + compatible = "qcom,wcnss"; + qcom,smd-channels = "WCNSS_CTRL"; + + qcom,mmio = <&wcnss>; + + wcnss_bt: bluetooth { + compatible = "qcom,wcnss-bt"; + }; + + wcnss_wifi: wifi { + compatible = "qcom,wcnss-wlan"; + + interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx", "rx"; + + qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>; + qcom,smem-state-names = "tx-enable", + "tx-rings-empty"; + }; + }; + }; + }; + intc: interrupt-controller@b000000 { compatible = "qcom,msm-qgic2"; interrupt-controller;
Signature · 1 line
2.25.1
PATCH 2/3 arm64: dts: MSM8953: Add mpss nodes
In reply to Adam SkladowskiAdd nodes for remoteproc, smp2p and smsm to make it possible to use modem functionality on this platform.
--- arch/arm64/boot/dts/qcom/msm8953.dtsi | 87 +++++++++++++++++++++++++++ 1 file changed, 87 insertions(+)
arch/arm64/boot/dts/qcom/msm8953.dtsi +87 -0
@@ -326,6 +326,31 @@ rpmpd_opp_turbo: opp9 { }; }; + smp2p-modem { + compatible = "qcom,smp2p"; + qcom,smem = <435>, <428>; + + interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>; + + qcom,ipc = <&apcs 8 14>; + + qcom,local-pid = <0>; + qcom,remote-pid = <1>; + + smp2p_modem_out: master-kernel { + qcom,entry-name = "master-kernel"; + + #qcom,smem-state-cells = <1>; + }; + + smp2p_modem_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + smp2p-wcnss { compatible = "qcom,smp2p"; qcom,smem = <451>, <431>;
@@ -366,6 +391,14 @@ apps_smsm: apps@0 { #qcom,smem-state-cells = <1>; }; + modem_smsm: modem@1 { + reg = <1>; + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + wcnss_smsm: wcnss@6 { reg = <6>; interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
@@ -995,6 +1028,60 @@ spmi_bus: spmi@200f000 { #size-cells = <0>; }; + mpss: remoteproc@4080000 { + compatible = "qcom,msm8953-mss-pil"; + reg = <0x04080000 0x100>, + <0x04020000 0x040>; + reg-names = "qdsp6", "rmb"; + + interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>, + <&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>, + <&smp2p_modem_in 1 IRQ_TYPE_EDGE_RISING>, + <&smp2p_modem_in 2 IRQ_TYPE_EDGE_RISING>, + <&smp2p_modem_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", + "handover", "stop-ack"; + + power-domains = <&rpmpd MSM8953_VDDCX>, + <&rpmpd MSM8953_VDDMX>, + <&rpmpd MSM8953_VDDMD>; + power-domain-names = "cx", "mx","mss"; + + clocks = <&gcc GCC_MSS_CFG_AHB_CLK>, + <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>, + <&gcc GCC_BOOT_ROM_AHB_CLK>, + <&rpmcc RPM_SMD_XO_CLK_SRC>; + clock-names = "iface", "bus", "mem", "xo"; + + qcom,smem-states = <&smp2p_modem_out 0>; + qcom,smem-state-names = "stop"; + + resets = <&gcc GCC_MSS_BCR>; + reset-names = "mss_restart"; + + qcom,halt-regs = <&tcsr 0x18000 0x19000 0x1a000>; + + status = "disabled"; + + mba { + memory-region = <&mba_mem>; + }; + + mpss { + memory-region = <&mpss_mem>; + }; + + smd-edge { + interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>; + + qcom,smd-edge = <0>; + qcom,ipc = <&apcs 8 12>; + qcom,remote-pid = <1>; + + label = "modem"; + }; + }; + usb3: usb@70f8800 { compatible = "qcom,msm8953-dwc3", "qcom,dwc3"; reg = <0x070f8800 0x400>;
Signature · 1 line
2.25.1
PATCH 3/3 arm64: dts: MSM8953: Add lpass nodes
In reply to Adam SkladowskiAdd nodes for remoteproc, smp2p and smsm in preparation for audio support on this platform.
--- arch/arm64/boot/dts/qcom/msm8953.dtsi | 141 ++++++++++++++++++++++++++ 1 file changed, 141 insertions(+)
arch/arm64/boot/dts/qcom/msm8953.dtsi +141 -0
@@ -6,6 +6,9 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/power/qcom-rpmpd.h> +#include <dt-bindings/soc/qcom,apr.h> +#include <dt-bindings/sound/qcom,q6afe.h> +#include <dt-bindings/sound/qcom,q6asm.h> #include <dt-bindings/thermal/thermal.h> / {
@@ -326,6 +329,30 @@ rpmpd_opp_turbo: opp9 { }; }; + smp2p-adsp { + compatible = "qcom,smp2p"; + qcom,smem = <443>, <429>; + + interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>; + + mboxes = <&apcs 10>; + + qcom,local-pid = <0>; + qcom,remote-pid = <2>; + + smp2p_adsp_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + smp2p_adsp_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + smp2p-modem { compatible = "qcom,smp2p"; qcom,smem = <435>, <428>;
@@ -1532,6 +1559,120 @@ frame@b128000 { status = "disabled"; }; }; + + lpass: remoteproc@c200000 { + compatible = "qcom,msm8953-adsp-pil"; + reg = <0x0c200000 0x100>; + + interrupts-extended = <&intc 0 293 IRQ_TYPE_EDGE_RISING>, + <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>, + <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>, + <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>, + <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", + "handover", "stop-ack"; + clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>; + clock-names = "xo"; + + power-domains = <&rpmpd MSM8953_VDDCX>; + power-domain-names = "cx"; + + memory-region = <&adsp_fw_mem>; + + qcom,smem-states = <&smp2p_adsp_out 0>; + qcom,smem-state-names = "stop"; + + status = "disabled"; + + smd-edge { + interrupts = <GIC_SPI 289 IRQ_TYPE_EDGE_RISING>; + + label = "lpass"; + mboxes = <&apcs 8>; + qcom,smd-edge = <1>; + qcom,remote-pid = <2>; + + apr { + compatible = "qcom,apr-v2"; + qcom,smd-channels = "apr_audio_svc"; + qcom,apr-domain = <APR_DOMAIN_ADSP>; + #address-cells = <1>; + #size-cells = <0>; + + q6core: service@3 { + reg = <APR_SVC_ADSP_CORE>; + compatible = "qcom,q6core"; + }; + + q6afe: service@4 { + compatible = "qcom,q6afe"; + reg = <APR_SVC_AFE>; + q6afedai: dais { + compatible = "qcom,q6afe-dais"; + #address-cells = <1>; + #size-cells = <0>; + #sound-dai-cells = <1>; + + dai@16 { + reg = <PRIMARY_MI2S_RX>; + qcom,sd-lines = <0 1>; + }; + dai@20 { + reg = <TERTIARY_MI2S_TX>; + qcom,sd-lines = <0 1>; + }; + dai@127 { + reg = <QUINARY_MI2S_RX>; + qcom,sd-lines = <0>; + }; + }; + + q6afecc: clock-controller { + compatible = "qcom,q6afe-clocks"; + #clock-cells = <2>; + }; + }; + + q6asm: service@7 { + compatible = "qcom,q6asm"; + reg = <APR_SVC_ASM>; + q6asmdai: dais { + compatible = "qcom,q6asm-dais"; + #address-cells = <1>; + #size-cells = <0>; + #sound-dai-cells = <1>; + + dai@0 { + reg = <0>; + direction = <Q6ASM_DAI_RX>; + }; + dai@1 { + reg = <1>; + direction = <Q6ASM_DAI_TX>; + }; + dai@2 { + reg = <2>; + direction = <Q6ASM_DAI_RX>; + }; + dai@3 { + reg = <3>; + direction = <Q6ASM_DAI_RX>; + is-compress-dai; + }; + }; + }; + + q6adm: service@8 { + compatible = "qcom,q6adm"; + reg = <APR_SVC_ADM>; + q6routing: routing { + compatible = "qcom,q6adm-routing"; + #sound-dai-cells = <0>; + }; + }; + }; + }; + }; }; thermal-zones {
Signature · 1 line
2.25.1
Quoted 8 lines · Adam Skladowski
This patch series introduce nodes required for bringing remoteproc cores.
Adam Skladowski (3):
arm64: dts: MSM8953: Add wcnss nodes
arm64: dts: MSM8953: Add mpss nodes
arm64: dts: MSM8953: Add lpass nodes[...]
Applied, thanks!
[1/3] arm64: dts: MSM8953: Add wcnss nodes
commit: b12428640ebeea3ee7e7ae817e1bd345612537df
[2/3] arm64: dts: MSM8953: Add mpss nodes
commit: 2bbada24e8a6c9eaf5caf015688dba0dcc3925d7
[3/3] arm64: dts: MSM8953: Add lpass nodes
commit: e58d100fa24309291ec500f9d161ff1ade20cabdBest regards,
Signature · 1 line
Bjorn Andersson <[email protected]>