dmaengine: dw-edma: Add support for native HDMA
Subsystems (5)
v9 cover dmaengine: dw-edma: Add support for native HDMA
Add support for HDMA NATIVE, as long the IP design has set the compatible register map parameter-HDMA_NATIVE, which allows compatibility for native HDMA register configuration.
The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP. And the native HDMA registers are different from eDMA,
so this patch add support for HDMA NATIVE mode.
HDMA write and read channels operate independently to maximize the performance of the HDMA read and write data transfer over the link When you configure the HDMA with multiple read channels, then it uses a round robin (RR) arbitration scheme to select the next read channel to be serviced.The same applies when youhave multiple write channels.
The native HDMA driver also supports a maximum of 16 independent channels (8 write + 8 read), which can run simultaneously. Both SAR (Source Address Register) and DAR (Destination Address Register) are aligned to byte.
Cai Huoqing (1):
dmaengine: dw-edma: Add support for native HDMA
Cai huoqing (3):
dmaengine: dw-edma: Rename dw_edma_core_ops structure to
dw_edma_plat_ops
dmaengine: dw-edma: Create a new dw_edma_core_ops structure to
abstract controller operation
dmaengine: dw-edma: Add HDMA DebugFS support
v8->v9:
[3/4]
1.Drop an empty line.
[4/4]
2.Update commit log.
3.Remove unused macro
v8 link:
https://lore.kernel.org/lkml/[email protected]/
drivers/dma/dw-edma/Makefile | 8 +- drivers/dma/dw-edma/dw-edma-core.c | 86 ++---- drivers/dma/dw-edma/dw-edma-core.h | 58 ++++ drivers/dma/dw-edma/dw-edma-pcie.c | 4 +- drivers/dma/dw-edma/dw-edma-v0-core.c | 85 +++++- drivers/dma/dw-edma/dw-edma-v0-core.h | 14 +- drivers/dma/dw-edma/dw-hdma-v0-core.c | 296 +++++++++++++++++++ drivers/dma/dw-edma/dw-hdma-v0-core.h | 17 ++ drivers/dma/dw-edma/dw-hdma-v0-debugfs.c | 170 +++++++++++ drivers/dma/dw-edma/dw-hdma-v0-debugfs.h | 22 ++ drivers/dma/dw-edma/dw-hdma-v0-regs.h | 129 ++++++++ drivers/pci/controller/dwc/pcie-designware.c | 2 +- include/linux/dma/edma.h | 7 +- 13 files changed, 807 insertions(+), 91 deletions(-) create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.h create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.h create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-regs.h
Signature · 1 line
2.34.1
PATCH RESEND v9 1/4 dmaengine: dw-edma: Rename dw_edma_core_ops structure to dw_edma_plat_ops
From: Cai huoqing <[email protected]>
The dw_edma_core_ops structure contains a set of the operations:
device IRQ numbers getter, CPU/PCI address translation. Based on the functions semantics the structure name "dw_edma_plat_ops" looks more descriptive since indeed the operations are platform-specific. The "dw_edma_core_ops" name shall be used for a structure with the IP-core specific set of callbacks in order to abstract out DW eDMA and DW HDMA setups. Such structure will be added in one of the next commit in the framework of the set of changes adding the DW HDMA device support.
Anyway the renaming was necessary to distinguish two types of the implementation callbacks:
1. DW eDMA/hDMA IP-core specific operations: device-specific CSR setups in one or another aspect of the DMA-engine initialization.
2. DW eDMA/hDMA platform specific operations: the DMA device environment configs like IRQs, address translation, etc.
---v8->v9: No change
v8 link:
https://lore.kernel.org/lkml/[email protected]/
drivers/dma/dw-edma/dw-edma-pcie.c | 4 ++-- drivers/pci/controller/dwc/pcie-designware.c | 2 +- include/linux/dma/edma.h | 4 ++-- 3 files changed, 5 insertions(+), 5 deletions(-)
drivers/dma/dw-edma/dw-edma-pcie.c +2 -2
@@ -109,7 +109,7 @@ static u64 dw_edma_pcie_address(struct device *dev, phys_addr_t cpu_addr)return region.start; } -static const struct dw_edma_core_ops dw_edma_pcie_core_ops = { +static const struct dw_edma_plat_ops dw_edma_pcie_plat_ops = { .irq_vector = dw_edma_pcie_irq_vector, .pci_address = dw_edma_pcie_address, };
@@ -225,7 +225,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev, chip->mf = vsec_data.mf; chip->nr_irqs = nr_irqs; - chip->ops = &dw_edma_pcie_core_ops; + chip->ops = &dw_edma_pcie_plat_ops; chip->ll_wr_cnt = vsec_data.wr_ch_cnt; chip->ll_rd_cnt = vsec_data.rd_ch_cnt;
drivers/pci/controller/dwc/pcie-designware.c +1 -1
@@ -828,7 +828,7 @@ static int dw_pcie_edma_irq_vector(struct device *dev, unsigned int nr)return platform_get_irq_byname_optional (pdev, name); } -static struct dw_edma_core_ops dw_pcie_edma_ops = { +static struct dw_edma_plat_ops dw_pcie_edma_ops = { .irq_vector = dw_pcie_edma_irq_vector, };
include/linux/dma/edma.h +2 -2
@@ -40,7 +40,7 @@ struct dw_edma_region {* iATU windows. That will be done by the controller * automatically. */ -struct dw_edma_core_ops { +struct dw_edma_plat_ops {int (*irq_vector)(struct device *dev,unsigned int nr);u64 (*pci_address)(struct device *dev,phys_addr_t cpu_addr); };
@@ -80,7 +80,7 @@ enum dw_edma_chip_flags {struct dw_edma_chip {struct device *dev;int nr_irqs; -const struct dw_edma_core_ops *ops; +const struct dw_edma_plat_ops *ops;u32 flags;void __iomem *reg_base;
Signature · 1 line
2.34.1
Re: [PATCH RESEND v9 1/4] dmaengine: dw-edma: Rename dw_edma_core_ops structure to dw_edma_plat_ops
Quoted 18 lines · Cai Huoqing
From: Cai huoqing <[email protected]>
The
dw_edma_core_opsstructure contains a set of the operations:
device IRQ numbers getter, CPU/PCI address translation. Based on the functions semantics the structure name "dw_edma_plat_ops" looks more descriptive since indeed the operations are platform-specific. The "dw_edma_core_ops" name shall be used for a structure with the IP-core specific set of callbacks in order to abstract out DW eDMA and DW HDMA setups. Such structure will be added in one of the next commit in the framework of the set of changes adding the DW HDMA device support.Anyway the renaming was necessary to distinguish two types of the implementation callbacks:
1. DW eDMA/hDMA IP-core specific operations: device-specific CSR setups in one or another aspect of the DMA-engine initialization.
2. DW eDMA/hDMA platform specific operations: the DMA device environment configs like IRQs, address translation, etc.
Quoted 2 lines
Signed-off-by Cai huoqing <[email protected]>Reviewed-by Serge Semin <[email protected]>
- Mani
Quoted 71 lines
---
v8->v9: No changev8 link:
https://lore.kernel.org/lkml/[email protected]/drivers/dma/dw-edma/dw-edma-pcie.c | 4 ++-- drivers/pci/controller/dwc/pcie-designware.c | 2 +- include/linux/dma/edma.h | 4 ++-- 3 files changed, 5 insertions(+), 5 deletions(-)drivers/dma/dw-edma/dw-edma-pcie.c +2
-2@@ -109,7 +109,7 @@ static u64 dw_edma_pcie_address(struct device *dev, phys_addr_t cpu_addr)return region.start; } -static const struct dw_edma_core_ops dw_edma_pcie_core_ops = { +static const struct dw_edma_plat_ops dw_edma_pcie_plat_ops = { .irq_vector = dw_edma_pcie_irq_vector, .pci_address = dw_edma_pcie_address, };@@ -225,7 +225,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev, chip->mf = vsec_data.mf; chip->nr_irqs = nr_irqs; - chip->ops = &dw_edma_pcie_core_ops; + chip->ops = &dw_edma_pcie_plat_ops; chip->ll_wr_cnt = vsec_data.wr_ch_cnt; chip->ll_rd_cnt = vsec_data.rd_ch_cnt;drivers/pci/controller/dwc/pcie-designware.c +1
-1@@ -828,7 +828,7 @@ static int dw_pcie_edma_irq_vector(struct device *dev, unsigned int nr)return platform_get_irq_byname_optional (pdev, name); } -static struct dw_edma_core_ops dw_pcie_edma_ops = { +static struct dw_edma_plat_ops dw_pcie_edma_ops = { .irq_vector = dw_pcie_edma_irq_vector, };include/linux/dma/edma.h +2
-2@@ -40,7 +40,7 @@ struct dw_edma_region {* iATU windows. That will be done by the controller * automatically. */ -struct dw_edma_core_ops { +struct dw_edma_plat_ops {int (*irq_vector)(struct device *dev,unsigned int nr);u64 (*pci_address)(struct device *dev,phys_addr_t cpu_addr); };@@ -80,7 +80,7 @@ enum dw_edma_chip_flags {struct dw_edma_chip {struct device *dev;int nr_irqs; -const struct dw_edma_core_ops *ops; +const struct dw_edma_plat_ops *ops;u32 flags;void __iomem *reg_base;Signature · 1 line
2.34.1
Signature · 1 line
மணிவண்ணன் சதாசிவம்
PATCH RESEND v9 2/4 dmaengine: dw-edma: Create a new dw_edma_core_ops structure to abstract controller operation
In reply to Cai HuoqingThe structure dw_edma_core_ops has a set of the pointers abstracting out the DW eDMA vX and DW HDMA Native controllers. And use dw_edma_v0_core_register to set up operation.
---v8->v9: No change
v8 link:
https://lore.kernel.org/lkml/[email protected]/
drivers/dma/dw-edma/dw-edma-core.c | 82 ++++++++------------------ drivers/dma/dw-edma/dw-edma-core.h | 58 ++++++++++++++++++ drivers/dma/dw-edma/dw-edma-v0-core.c | 85 +++++++++++++++++++++++---- drivers/dma/dw-edma/dw-edma-v0-core.h | 14 +---- 4 files changed, 157 insertions(+), 82 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +25 -57
@@ -183,6 +183,7 @@ static void vchan_free_desc(struct virt_dma_desc *vdesc)static int dw_edma_start_transfer (struct dw_edma_chan *chan) { +struct dw_edma *dw = chan->dw;struct dw_edma_chunk *child;struct dw_edma_desc *desc;struct virt_dma_desc *vd;
@@ -200,7 +201,7 @@ static int dw_edma_start_transfer(struct dw_edma_chan *chan)if (!child)return 0 ; -dw_edma_v0_core_start (child, !desc->xfer_sz); +dw_edma_core_start (dw, child, !desc->xfer_sz); desc->xfer_sz += child->ll_region.sz;dw_edma_free_burst (child);list_del (&child->list);
@@ -285,7 +286,7 @@ static int dw_edma_device_terminate_all(struct dma_chan *dchan) chan->configured = false; }else if (chan->status ==EDMA_ST_IDLE ) { chan->configured = false; - }else if (dw_edma_v0_core_ch_status (chan) ==DMA_COMPLETE ) { + }else if (dw_edma_core_ch_status (chan) ==DMA_COMPLETE ) {/* * The channel is in a false BUSY state, probably didn't * receive or lost an interrupt
@@ -594,8 +595,6 @@ static void dw_edma_done_interrupt(struct dw_edma_chan *chan)struct virt_dma_desc *vd;unsigned long flags; -dw_edma_v0_core_clear_done_int (chan); -spin_lock_irqsave (&chan->vc.lock, flags); vd =vchan_next_desc (&chan->vc);if (vd) {
@@ -636,8 +635,6 @@ static void dw_edma_abort_interrupt(struct dw_edma_chan *chan)struct virt_dma_desc *vd;unsigned long flags; -dw_edma_v0_core_clear_abort_int (chan); -spin_lock_irqsave (&chan->vc.lock, flags); vd =vchan_next_desc (&chan->vc);if (vd) {
@@ -649,63 +646,32 @@ static void dw_edma_abort_interrupt(struct dw_edma_chan *chan) chan->status =EDMA_ST_IDLE ; } -static irqreturn_t dw_edma_interrupt (int irq,void *data,bool write) +static inline irqreturn_t dw_edma_interrupt_write (int irq,void *data) {struct dw_edma_irq *dw_irq = data; -struct dw_edma *dw = dw_irq->dw; -unsigned long total, pos, val; -unsigned long off; -u32 mask; - -if (write) { - total = dw->wr_ch_cnt; - off =0 ; - mask = dw_irq->wr_mask; - }else { - total = dw->rd_ch_cnt; - off = dw->wr_ch_cnt; - mask = dw_irq->rd_mask; - } - - val =dw_edma_v0_core_status_done_int (dw, write ? -EDMA_DIR_WRITE : -EDMA_DIR_READ ); - val &= mask; -for_each_set_bit (pos, &val, total) { -struct dw_edma_chan *chan = &dw->chan[pos + off]; - -dw_edma_done_interrupt (chan); - } - - val =dw_edma_v0_core_status_abort_int (dw, write ? -EDMA_DIR_WRITE : -EDMA_DIR_READ ); - val &= mask; -for_each_set_bit (pos, &val, total) { -struct dw_edma_chan *chan = &dw->chan[pos + off]; - -dw_edma_abort_interrupt (chan); - } - -return IRQ_HANDLED ; -} -static inline irqreturn_t dw_edma_interrupt_write (int irq,void *data) -{ -return dw_edma_interrupt (irq, data, true); +return dw_edma_core_handle_int (dw_irq,EDMA_DIR_WRITE , + dw_edma_done_interrupt, + dw_edma_abort_interrupt); }static inline irqreturn_t dw_edma_interrupt_read (int irq,void *data) { -return dw_edma_interrupt (irq, data, false); +struct dw_edma_irq *dw_irq = data; + +return dw_edma_core_handle_int (dw_irq,EDMA_DIR_READ , + dw_edma_done_interrupt, + dw_edma_abort_interrupt); }static irqreturn_t dw_edma_interrupt_common (int irq,void *data) { -dw_edma_interrupt (irq, data, true); -dw_edma_interrupt (irq, data, false); +irqreturn_t ret =IRQ_NONE ; + + ret |=dw_edma_interrupt_write (irq, data); + ret |=dw_edma_interrupt_read (irq, data); -return IRQ_HANDLED ; +return ret; }static int dw_edma_alloc_chan_resources (struct dma_chan *dchan)
@@ -806,7 +772,7 @@ static int dw_edma_channel_setup(struct dw_edma *dw, u32 wr_alloc, u32 rd_alloc)vchan_init (&chan->vc, dma); -dw_edma_v0_core_device_config (chan); +dw_edma_core_ch_config (chan); }/* Set DMA channel capabilities */
@@ -951,14 +917,16 @@ int dw_edma_probe(struct dw_edma_chip *chip) dw->chip = chip; +dw_edma_v0_core_register (dw); +raw_spin_lock_init (&dw->lock); dw->wr_ch_cnt =min_t (u16, chip->ll_wr_cnt, -dw_edma_v0_core_ch_count (dw,EDMA_DIR_WRITE )); +dw_edma_core_ch_count (dw,EDMA_DIR_WRITE )); dw->wr_ch_cnt =min_t (u16, dw->wr_ch_cnt,EDMA_MAX_WR_CH ); dw->rd_ch_cnt =min_t (u16, chip->ll_rd_cnt, -dw_edma_v0_core_ch_count (dw,EDMA_DIR_READ )); +dw_edma_core_ch_count (dw,EDMA_DIR_READ )); dw->rd_ch_cnt =min_t (u16, dw->rd_ch_cnt,EDMA_MAX_RD_CH );if (!dw->wr_ch_cnt && !dw->rd_ch_cnt)
@@ -977,7 +945,7 @@ int dw_edma_probe(struct dw_edma_chip *chip) dev_name(chip->dev));/* Disable eDMA, only to establish the ideal initial conditions */ -dw_edma_v0_core_off (dw); +dw_edma_core_off (dw);/* Request IRQs */ err =dw_edma_irq_request (dw, &wr_alloc, &rd_alloc);
@@ -990,7 +958,7 @@ int dw_edma_probe(struct dw_edma_chip *chip) goto err_irq_free;/* Turn debugfs on */ -dw_edma_v0_core_debugfs_on (dw); +dw_edma_core_debugfs_on (dw); chip->dw = dw;
@@ -1016,7 +984,7 @@ int dw_edma_remove(struct dw_edma_chip *chip)return -ENODEV ;/* Disable eDMA */ -dw_edma_v0_core_off (dw); +dw_edma_core_off (dw);/* Free irqs */ for (i = (dw->nr_irqs -1 ); i >=0 ; i--)
drivers/dma/dw-edma/dw-edma-core.h +58 -0
68 lines not on this page · raw message
drivers/dma/dw-edma/dw-edma-v0-core.c +72 -13
158 lines not on this page · raw message
drivers/dma/dw-edma/dw-edma-v0-core.h +2 -12
@@ -11,17 +11,7 @@#include <linux/dma/edma.h> -/* eDMA management callbacks */ -void dw_edma_v0_core_off (struct dw_edma *chan); -u16 dw_edma_v0_core_ch_count (struct dw_edma *chan,enum dw_edma_dir dir); -enum dma_status dw_edma_v0_core_ch_status (struct dw_edma_chan *chan); -void dw_edma_v0_core_clear_done_int (struct dw_edma_chan *chan); -void dw_edma_v0_core_clear_abort_int (struct dw_edma_chan *chan); -u32 dw_edma_v0_core_status_done_int (struct dw_edma *chan,enum dw_edma_dir dir); -u32 dw_edma_v0_core_status_abort_int (struct dw_edma *chan,enum dw_edma_dir dir); -void dw_edma_v0_core_start (struct dw_edma_chunk *chunk,bool first); -int dw_edma_v0_core_device_config (struct dw_edma_chan *chan); -/* eDMA debug fs callbacks */ -void dw_edma_v0_core_debugfs_on (struct dw_edma *dw); +/* eDMA core register */ +void dw_edma_v0_core_register (struct dw_edma *dw);#endif /* _DW_EDMA_V0_CORE_H */
Signature · 1 line
2.34.1
Re: [PATCH RESEND v9 2/4] dmaengine: dw-edma: Create a new dw_edma_core_ops structure to abstract controller operation
Quoted 5 lines · Cai Huoqing
The structure
dw_edma_core_opshas a set of the pointers abstracting out the DW eDMA vX and DW HDMA Native controllers. And usedw_edma_v0_core_registerto set up operation.Signed-off-by Cai Huoqing <[email protected]>
- Mani
Quoted 468 lines
Reviewed-by Serge Semin <[email protected]>---
v8->v9: No changev8 link:
https://lore.kernel.org/lkml/[email protected]/drivers/dma/dw-edma/dw-edma-core.c | 82 ++++++++------------------ drivers/dma/dw-edma/dw-edma-core.h | 58 ++++++++++++++++++ drivers/dma/dw-edma/dw-edma-v0-core.c | 85 +++++++++++++++++++++++---- drivers/dma/dw-edma/dw-edma-v0-core.h | 14 +---- 4 files changed, 157 insertions(+), 82 deletions(-)drivers/dma/dw-edma/dw-edma-core.c +25
-57@@ -183,6 +183,7 @@ static void vchan_free_desc(struct virt_dma_desc *vdesc)static int dw_edma_start_transfer (struct dw_edma_chan *chan) { +struct dw_edma *dw = chan->dw;struct dw_edma_chunk *child;struct dw_edma_desc *desc;struct virt_dma_desc *vd;@@ -200,7 +201,7 @@ static int dw_edma_start_transfer(struct dw_edma_chan *chan)if (!child)return 0 ; -dw_edma_v0_core_start (child, !desc->xfer_sz); +dw_edma_core_start (dw, child, !desc->xfer_sz); desc->xfer_sz += child->ll_region.sz;dw_edma_free_burst (child);list_del (&child->list);@@ -285,7 +286,7 @@ static int dw_edma_device_terminate_all(struct dma_chan *dchan) chan->configured = false; }else if (chan->status ==EDMA_ST_IDLE ) { chan->configured = false; - }else if (dw_edma_v0_core_ch_status (chan) ==DMA_COMPLETE ) { + }else if (dw_edma_core_ch_status (chan) ==DMA_COMPLETE ) {/* * The channel is in a false BUSY state, probably didn't * receive or lost an interrupt @@ -594,8 +595,6 @@ static void dw_edma_done_interrupt(struct dw_edma_chan *chan)struct virt_dma_desc *vd;unsigned long flags; -dw_edma_v0_core_clear_done_int (chan); -spin_lock_irqsave (&chan->vc.lock, flags); vd =vchan_next_desc (&chan->vc);if (vd) {@@ -636,8 +635,6 @@ static void dw_edma_abort_interrupt(struct dw_edma_chan *chan)struct virt_dma_desc *vd;unsigned long flags; -dw_edma_v0_core_clear_abort_int (chan); -spin_lock_irqsave (&chan->vc.lock, flags); vd =vchan_next_desc (&chan->vc);if (vd) {@@ -649,63 +646,32 @@ static void dw_edma_abort_interrupt(struct dw_edma_chan *chan) chan->status =EDMA_ST_IDLE ; } -static irqreturn_t dw_edma_interrupt (int irq,void *data,bool write) +static inline irqreturn_t dw_edma_interrupt_write (int irq,void *data) {struct dw_edma_irq *dw_irq = data; -struct dw_edma *dw = dw_irq->dw; -unsigned long total, pos, val; -unsigned long off; -u32 mask; - -if (write) { - total = dw->wr_ch_cnt; - off =0 ; - mask = dw_irq->wr_mask; - }else { - total = dw->rd_ch_cnt; - off = dw->wr_ch_cnt; - mask = dw_irq->rd_mask; - } - - val =dw_edma_v0_core_status_done_int (dw, write ? -EDMA_DIR_WRITE : -EDMA_DIR_READ ); - val &= mask; -for_each_set_bit (pos, &val, total) { -struct dw_edma_chan *chan = &dw->chan[pos + off]; - -dw_edma_done_interrupt (chan); - } - - val =dw_edma_v0_core_status_abort_int (dw, write ? -EDMA_DIR_WRITE : -EDMA_DIR_READ ); - val &= mask; -for_each_set_bit (pos, &val, total) { -struct dw_edma_chan *chan = &dw->chan[pos + off]; - -dw_edma_abort_interrupt (chan); - } - -return IRQ_HANDLED ; -} -static inline irqreturn_t dw_edma_interrupt_write (int irq,void *data) -{ -return dw_edma_interrupt (irq, data, true); +return dw_edma_core_handle_int (dw_irq,EDMA_DIR_WRITE , + dw_edma_done_interrupt, + dw_edma_abort_interrupt); }static inline irqreturn_t dw_edma_interrupt_read (int irq,void *data) { -return dw_edma_interrupt (irq, data, false); +struct dw_edma_irq *dw_irq = data; + +return dw_edma_core_handle_int (dw_irq,EDMA_DIR_READ , + dw_edma_done_interrupt, + dw_edma_abort_interrupt); }static irqreturn_t dw_edma_interrupt_common (int irq,void *data) { -dw_edma_interrupt (irq, data, true); -dw_edma_interrupt (irq, data, false); +irqreturn_t ret =IRQ_NONE ; + + ret |=dw_edma_interrupt_write (irq, data); + ret |=dw_edma_interrupt_read (irq, data); -return IRQ_HANDLED ; +return ret; }static int dw_edma_alloc_chan_resources (struct dma_chan *dchan)@@ -806,7 +772,7 @@ static int dw_edma_channel_setup(struct dw_edma *dw, u32 wr_alloc, u32 rd_alloc)vchan_init (&chan->vc, dma); -dw_edma_v0_core_device_config (chan); +dw_edma_core_ch_config (chan); }/* Set DMA channel capabilities */ @@ -951,14 +917,16 @@ int dw_edma_probe(struct dw_edma_chip *chip) dw->chip = chip; +dw_edma_v0_core_register (dw); +raw_spin_lock_init (&dw->lock); dw->wr_ch_cnt =min_t (u16, chip->ll_wr_cnt, -dw_edma_v0_core_ch_count (dw,EDMA_DIR_WRITE )); +dw_edma_core_ch_count (dw,EDMA_DIR_WRITE )); dw->wr_ch_cnt =min_t (u16, dw->wr_ch_cnt,EDMA_MAX_WR_CH ); dw->rd_ch_cnt =min_t (u16, chip->ll_rd_cnt, -dw_edma_v0_core_ch_count (dw,EDMA_DIR_READ )); +dw_edma_core_ch_count (dw,EDMA_DIR_READ )); dw->rd_ch_cnt =min_t (u16, dw->rd_ch_cnt,EDMA_MAX_RD_CH );if (!dw->wr_ch_cnt && !dw->rd_ch_cnt)@@ -977,7 +945,7 @@ int dw_edma_probe(struct dw_edma_chip *chip) dev_name(chip->dev));/* Disable eDMA, only to establish the ideal initial conditions */ -dw_edma_v0_core_off (dw); +dw_edma_core_off (dw);/* Request IRQs */ err =dw_edma_irq_request (dw, &wr_alloc, &rd_alloc);@@ -990,7 +958,7 @@ int dw_edma_probe(struct dw_edma_chip *chip) goto err_irq_free;/* Turn debugfs on */ -dw_edma_v0_core_debugfs_on (dw); +dw_edma_core_debugfs_on (dw); chip->dw = dw;@@ -1016,7 +984,7 @@ int dw_edma_remove(struct dw_edma_chip *chip)return -ENODEV ;/* Disable eDMA */ -dw_edma_v0_core_off (dw); +dw_edma_core_off (dw);/* Free irqs */ for (i = (dw->nr_irqs -1 ); i >=0 ; i--)drivers/dma/dw-edma/dw-edma-core.h +58
-0@@ -111,6 +111,21 @@ struct dw_edma {raw_spinlock_t lock;/* Only for legacy */ struct dw_edma_chip *chip; + +const struct dw_edma_core_ops *core; +}; + +typedef void (*dw_edma_handler_t )(struct dw_edma_chan *); + +struct dw_edma_core_ops { +void (*off)(struct dw_edma *dw); +u16 (*ch_count)(struct dw_edma *dw,enum dw_edma_dir dir); +enum dma_status (*ch_status)(struct dw_edma_chan *chan); +irqreturn_t (*handle_int)(struct dw_edma_irq *dw_irq,enum dw_edma_dir dir, +dw_edma_handler_t done,dw_edma_handler_t abort); +void (*start)(struct dw_edma_chunk *chunk,bool first); +void (*ch_config)(struct dw_edma_chan *chan); +void (*debugfs_on)(struct dw_edma *dw); };struct dw_edma_sg {@@ -148,4 +163,47 @@ struct dw_edma_chan *dchan2dw_edma_chan(struct dma_chan *dchan)return vc2dw_edma_chan (to_virt_chan (dchan)); } +static inline +void dw_edma_core_off (struct dw_edma *dw) +{ + dw->core->off (dw); +} + +static inline +u16 dw_edma_core_ch_count (struct dw_edma *dw,enum dw_edma_dir dir) +{ +return dw->core->ch_count (dw, dir); +} + +static inline +enum dma_status dw_edma_core_ch_status (struct dw_edma_chan *chan) +{ +return chan->dw->core->ch_status (chan); +} + +static inline irqreturn_t +dw_edma_core_handle_int (struct dw_edma_irq *dw_irq,enum dw_edma_dir dir, +dw_edma_handler_t done,dw_edma_handler_t abort) +{ +return dw_irq->dw->core->handle_int (dw_irq, dir, done, abort); +} + +static inline +void dw_edma_core_start (struct dw_edma *dw,struct dw_edma_chunk *chunk,bool first) +{ + dw->core->start (chunk, first); +} + +static inline +void dw_edma_core_ch_config (struct dw_edma_chan *chan) +{ + chan->dw->core->ch_config (chan); +} + +static inline +void dw_edma_core_debugfs_on (struct dw_edma *dw) +{ + dw->core->debugfs_on (dw); +} +#endif /* _DW_EDMA_CORE_H */ drivers/dma/dw-edma/dw-edma-v0-core.c +72
-13@@ -7,7 +7,7 @@*/ #include <linux/bitfield.h> - +#include <linux/irqreturn.h> #include <linux/io-64-nonatomic-lo-hi.h> #include "dw-edma-core.h" @@ -160,7 +160,7 @@ static inline u32 readl_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,readl_ch (dw, dir, ch, &(__dw_ch_regs (dw, dir, ch)->name)) /* eDMA management callbacks */ -void dw_edma_v0_core_off (struct dw_edma *dw) +static void dw_edma_v0_core_off (struct dw_edma *dw) {SET_BOTH_32 (dw, int_mask,EDMA_V0_DONE_INT_MASK |EDMA_V0_ABORT_INT_MASK );@@ -169,7 +169,7 @@ void dw_edma_v0_core_off(struct dw_edma *dw)SET_BOTH_32 (dw, engine_en,0 ); } -u16 dw_edma_v0_core_ch_count (struct dw_edma *dw,enum dw_edma_dir dir) +static u16 dw_edma_v0_core_ch_count (struct dw_edma *dw,enum dw_edma_dir dir) {u32 num_ch;@@ -186,7 +186,7 @@ u16 dw_edma_v0_core_ch_count(struct dw_edma *dw, enum dw_edma_dir dir)return (u16 )num_ch; } -enum dma_status dw_edma_v0_core_ch_status (struct dw_edma_chan *chan) +static enum dma_status dw_edma_v0_core_ch_status (struct dw_edma_chan *chan) {struct dw_edma *dw = chan->dw;u32 tmp;@@ -202,7 +202,7 @@ enum dma_status dw_edma_v0_core_ch_status(struct dw_edma_chan *chan)return DMA_ERROR ; } -void dw_edma_v0_core_clear_done_int (struct dw_edma_chan *chan) +static void dw_edma_v0_core_clear_done_int (struct dw_edma_chan *chan) {struct dw_edma *dw = chan->dw;@@ -210,7 +210,7 @@ void dw_edma_v0_core_clear_done_int(struct dw_edma_chan *chan) FIELD_PREP(EDMA_V0_DONE_INT_MASK, BIT(chan->id))); } -void dw_edma_v0_core_clear_abort_int (struct dw_edma_chan *chan) +static void dw_edma_v0_core_clear_abort_int (struct dw_edma_chan *chan) {struct dw_edma *dw = chan->dw;@@ -218,18 +218,64 @@ void dw_edma_v0_core_clear_abort_int(struct dw_edma_chan *chan) FIELD_PREP(EDMA_V0_ABORT_INT_MASK, BIT(chan->id))); } -u32 dw_edma_v0_core_status_done_int (struct dw_edma *dw,enum dw_edma_dir dir) +static u32 dw_edma_v0_core_status_done_int (struct dw_edma *dw,enum dw_edma_dir dir) {return FIELD_GET (EDMA_V0_DONE_INT_MASK ,GET_RW_32 (dw, dir, int_status)); } -u32 dw_edma_v0_core_status_abort_int (struct dw_edma *dw,enum dw_edma_dir dir) +static u32 dw_edma_v0_core_status_abort_int (struct dw_edma *dw,enum dw_edma_dir dir) {return FIELD_GET (EDMA_V0_ABORT_INT_MASK ,GET_RW_32 (dw, dir, int_status)); } +static irqreturn_t +dw_edma_v0_core_handle_int (struct dw_edma_irq *dw_irq,enum dw_edma_dir dir, +dw_edma_handler_t done,dw_edma_handler_t abort) +{ +struct dw_edma *dw = dw_irq->dw; +unsigned long total, pos, val; +irqreturn_t ret =IRQ_NONE ; +struct dw_edma_chan *chan; +unsigned long off; +u32 mask; + +if (dir ==EDMA_DIR_WRITE ) { + total = dw->wr_ch_cnt; + off =0 ; + mask = dw_irq->wr_mask; + }else { + total = dw->rd_ch_cnt; + off = dw->wr_ch_cnt; + mask = dw_irq->rd_mask; + } + + val =dw_edma_v0_core_status_done_int (dw, dir); + val &= mask; +for_each_set_bit (pos, &val, total) { + chan = &dw->chan[pos + off]; + +dw_edma_v0_core_clear_done_int (chan); +done (chan); + + ret =IRQ_HANDLED ; + } + + val =dw_edma_v0_core_status_abort_int (dw, dir); + val &= mask; +for_each_set_bit (pos, &val, total) { + chan = &dw->chan[pos + off]; + +dw_edma_v0_core_clear_abort_int (chan); +abort (chan); + + ret =IRQ_HANDLED ; + } + +return ret; +} +static void dw_edma_v0_write_ll_data (struct dw_edma_chunk *chunk,int i,u32 control,u32 size,u64 sar,u64 dar) {@@ -300,7 +346,7 @@ static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)dw_edma_v0_write_ll_link (chunk, i, control, chunk->ll_region.paddr); } -void dw_edma_v0_core_start (struct dw_edma_chunk *chunk,bool first) +static void dw_edma_v0_core_start (struct dw_edma_chunk *chunk,bool first) {struct dw_edma_chan *chan = chunk->chan;struct dw_edma *dw = chan->dw;@@ -371,7 +417,7 @@ void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first) FIELD_PREP(EDMA_V0_DOORBELL_CH_MASK, chan->id)); } -int dw_edma_v0_core_device_config (struct dw_edma_chan *chan) +static void dw_edma_v0_core_ch_config (struct dw_edma_chan *chan) {struct dw_edma *dw = chan->dw;u32 tmp =0 ;@@ -438,12 +484,25 @@ int dw_edma_v0_core_device_config(struct dw_edma_chan *chan)SET_RW_32 (dw, chan->dir, ch67_imwr_data, tmp);break ; } - -return 0 ; }/* eDMA debugfs callbacks */ -void dw_edma_v0_core_debugfs_on (struct dw_edma *dw) +static void dw_edma_v0_core_debugfs_on (struct dw_edma *dw) {dw_edma_v0_debugfs_on (dw); } + +static const struct dw_edma_core_ops dw_edma_v0_core = { + .off = dw_edma_v0_core_off, + .ch_count = dw_edma_v0_core_ch_count, + .ch_status = dw_edma_v0_core_ch_status, + .handle_int = dw_edma_v0_core_handle_int, + .start = dw_edma_v0_core_start, + .ch_config = dw_edma_v0_core_ch_config, + .debugfs_on = dw_edma_v0_core_debugfs_on, +}; + +void dw_edma_v0_core_register (struct dw_edma *dw) +{ + dw->core = &dw_edma_v0_core; +}drivers/dma/dw-edma/dw-edma-v0-core.h +2
-12@@ -11,17 +11,7 @@#include <linux/dma/edma.h> -/* eDMA management callbacks */ -void dw_edma_v0_core_off (struct dw_edma *chan); -u16 dw_edma_v0_core_ch_count (struct dw_edma *chan,enum dw_edma_dir dir); -enum dma_status dw_edma_v0_core_ch_status (struct dw_edma_chan *chan); -void dw_edma_v0_core_clear_done_int (struct dw_edma_chan *chan); -void dw_edma_v0_core_clear_abort_int (struct dw_edma_chan *chan); -u32 dw_edma_v0_core_status_done_int (struct dw_edma *chan,enum dw_edma_dir dir); -u32 dw_edma_v0_core_status_abort_int (struct dw_edma *chan,enum dw_edma_dir dir); -void dw_edma_v0_core_start (struct dw_edma_chunk *chunk,bool first); -int dw_edma_v0_core_device_config (struct dw_edma_chan *chan); -/* eDMA debug fs callbacks */ -void dw_edma_v0_core_debugfs_on (struct dw_edma *dw); +/* eDMA core register */ +void dw_edma_v0_core_register (struct dw_edma *dw);#endif /* _DW_EDMA_V0_CORE_H */ Signature · 1 line
2.34.1
Signature · 1 line
மணிவண்ணன் சதாசிவம்
PATCH RESEND v9 3/4 dmaengine: dw-edma: Add support for native HDMA
In reply to Cai HuoqingAdd support for HDMA NATIVE, as long the IP design has set the compatible register map parameter-HDMA_NATIVE, which allows compatibility for native HDMA register configuration.
The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP. And the native HDMA registers are different from eDMA, so this patch add support for HDMA NATIVE mode.
HDMA write and read channels operate independently to maximize the performance of the HDMA read and write data transfer over the link When you configure the HDMA with multiple read channels, then it uses a round robin (RR) arbitration scheme to select the next read channel to be serviced.The same applies when you have multiple write channels.
The native HDMA driver also supports a maximum of 16 independent channels (8 write + 8 read), which can run simultaneously. Both SAR (Source Address Register) and DAR (Destination Address Register) are aligned to byte.
---v8->v9:
1.Drop an empty line.
v8 link:
https://lore.kernel.org/lkml/[email protected]/
drivers/dma/dw-edma/Makefile | 5 +- drivers/dma/dw-edma/dw-edma-core.c | 6 +- drivers/dma/dw-edma/dw-hdma-v0-core.c | 294 ++++++++++++++++++++++++++ drivers/dma/dw-edma/dw-hdma-v0-core.h | 17 ++ drivers/dma/dw-edma/dw-hdma-v0-regs.h | 129 +++++++++++ include/linux/dma/edma.h | 3 +- 6 files changed, 450 insertions(+), 4 deletions(-) create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.h create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-regs.h
drivers/dma/dw-edma/Makefile +3 -2
@@ -2,6 +2,7 @@ obj-$(CONFIG_DW_EDMA) += dw-edma.o dw-edma-$(CONFIG_DEBUG_FS) := dw-edma-v0-debugfs.o -dw-edma-objs := dw-edma-core.o \ - dw-edma-v0-core.o $(dw-edma-y) +dw-edma-objs := dw-edma-core.o \ + dw-edma-v0-core.o \ + dw-hdma-v0-core.o $(dw-edma-y) obj-$(CONFIG_DW_EDMA_PCIE) += dw-edma-pcie.o
drivers/dma/dw-edma/dw-edma-core.c +5 -1
@@ -18,6 +18,7 @@#include "dw-edma-core.h" #include "dw-edma-v0-core.h" +#include "dw-hdma-v0-core.h" #include "../dmaengine.h" #include "../virt-dma.h"
@@ -917,7 +918,10 @@ int dw_edma_probe(struct dw_edma_chip *chip) dw->chip = chip; -dw_edma_v0_core_register (dw); +if (dw->chip->mf ==EDMA_MF_HDMA_NATIVE ) +dw_hdma_v0_core_register (dw); +else +dw_edma_v0_core_register (dw);raw_spin_lock_init (&dw->lock);
drivers/dma/dw-edma/dw-hdma-v0-core.c new file +294 -0
294 lines not on this page · raw message
drivers/dma/dw-edma/dw-hdma-v0-core.h new file +17 -0
@@ -0,0 +1,17 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Copyright (c) 2023 Cai Huoqing +* Synopsys DesignWare HDMA v0 core +* +* Author: Cai Huoqing <[email protected]> +*/ + +#ifndef _DW_HDMA_V0_CORE_H +#define _DW_HDMA_V0_CORE_H + +#include <linux/dma/edma.h> + +/* HDMA core register */ +void dw_hdma_v0_core_register (struct dw_edma *dw); + +#endif /* _DW_HDMA_V0_CORE_H */
drivers/dma/dw-edma/dw-hdma-v0-regs.h new file +129 -0
129 lines not on this page · raw message
include/linux/dma/edma.h +2 -1
@@ -48,7 +48,8 @@ struct dw_edma_plat_ops {enum dw_edma_map_format {EDMA_MF_EDMA_LEGACY =0x0 ,EDMA_MF_EDMA_UNROLL =0x1 , -EDMA_MF_HDMA_COMPAT =0x5 +EDMA_MF_HDMA_COMPAT =0x5 , +EDMA_MF_HDMA_NATIVE =0x7 , };/**
Signature · 1 line
2.34.1
Quoted 15 lines · Cai Huoqing
Add support for HDMA NATIVE, as long the IP design has set the compatible register map parameter-HDMA_NATIVE, which allows compatibility for native HDMA register configuration.
The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP. And the native HDMA registers are different from eDMA, so this patch add support for HDMA NATIVE mode.
HDMA write and read channels operate independently to maximize the performance of the HDMA read and write data transfer over the link When you configure the HDMA with multiple read channels, then it uses a round robin (RR) arbitration scheme to select the next read channel to be serviced.The same applies when you have multiple write channels.
Quoted 6 lines
The native HDMA driver also supports a maximum of 16 independent channels (8 write + 8 read), which can run simultaneously. Both SAR (Source Address Register) and DAR (Destination Address Register) are aligned to byte.
Signed-off-by Cai Huoqing <[email protected]>
- Mani
Quoted 532 lines
Reviewed-by Serge Semin <[email protected]>---
v8->v9:
1.Drop an empty line.v8 link:
https://lore.kernel.org/lkml/[email protected]/drivers/dma/dw-edma/Makefile | 5 +- drivers/dma/dw-edma/dw-edma-core.c | 6 +- drivers/dma/dw-edma/dw-hdma-v0-core.c | 294 ++++++++++++++++++++++++++ drivers/dma/dw-edma/dw-hdma-v0-core.h | 17 ++ drivers/dma/dw-edma/dw-hdma-v0-regs.h | 129 +++++++++++ include/linux/dma/edma.h | 3 +- 6 files changed, 450 insertions(+), 4 deletions(-) create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.h create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-regs.hdrivers/dma/dw-edma/Makefile +3
-2@@ -2,6 +2,7 @@ obj-$(CONFIG_DW_EDMA) += dw-edma.o dw-edma-$(CONFIG_DEBUG_FS) := dw-edma-v0-debugfs.o -dw-edma-objs := dw-edma-core.o \ - dw-edma-v0-core.o $(dw-edma-y) +dw-edma-objs := dw-edma-core.o \ + dw-edma-v0-core.o \ + dw-hdma-v0-core.o $(dw-edma-y) obj-$(CONFIG_DW_EDMA_PCIE) += dw-edma-pcie.odrivers/dma/dw-edma/dw-edma-core.c +5
-1@@ -18,6 +18,7 @@#include "dw-edma-core.h" #include "dw-edma-v0-core.h" +#include "dw-hdma-v0-core.h" #include "../dmaengine.h" #include "../virt-dma.h" @@ -917,7 +918,10 @@ int dw_edma_probe(struct dw_edma_chip *chip) dw->chip = chip; -dw_edma_v0_core_register (dw); +if (dw->chip->mf ==EDMA_MF_HDMA_NATIVE ) +dw_hdma_v0_core_register (dw); +else +dw_edma_v0_core_register (dw);raw_spin_lock_init (&dw->lock);drivers/dma/dw-edma/dw-hdma-v0-core.c new file +294
-0@@ -0,0 +1,294 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Copyright (c) 2023 Cai Huoqing +* Synopsys DesignWare HDMA v0 core +*/ + +#include <linux/bitfield.h> +#include <linux/irqreturn.h> +#include <linux/io-64-nonatomic-lo-hi.h> + +#include "dw-edma-core.h" +#include "dw-hdma-v0-core.h" +#include "dw-hdma-v0-regs.h" + +enum dw_hdma_control { +DW_HDMA_V0_CB =BIT (0 ), +DW_HDMA_V0_TCB =BIT (1 ), +DW_HDMA_V0_LLP =BIT (2 ), +DW_HDMA_V0_LIE =BIT (3 ), +DW_HDMA_V0_RIE =BIT (4 ), +DW_HDMA_V0_CCS =BIT (8 ), +DW_HDMA_V0_LLE =BIT (9 ), +}; + +static inline struct dw_hdma_v0_regs __iomem *__dw_regs (struct dw_edma *dw) +{ +return dw->chip->reg_base; +} + +static inline struct dw_hdma_v0_ch_regs __iomem * +__dw_ch_regs (struct dw_edma *dw,enum dw_edma_dir dir,u16 ch) +{ +if (dir ==EDMA_DIR_WRITE ) +return &(__dw_regs (dw)->ch[ch].wr); +else +return &(__dw_regs (dw)->ch[ch].rd); +} + +#define SET_CH_32 (dw, dir, ch, name, value) \ + writel(value, &(__dw_ch_regs(dw, dir, ch)->name)) + +#define GET_CH_32 (dw, dir, ch, name) \ + readl(&(__dw_ch_regs(dw, dir, ch)->name)) + +#define SET_BOTH_CH_32 (dw, ch, name, value) \ + do { \ + writel(value, &(__dw_ch_regs(dw, EDMA_DIR_WRITE, ch)->name)); \ + writel(value, &(__dw_ch_regs(dw, EDMA_DIR_READ, ch)->name)); \ + } while (0) + +/* HDMA management callbacks */ +static void dw_hdma_v0_core_off (struct dw_edma *dw) +{ +int id; + +for (id =0 ; id <HDMA_V0_MAX_NR_CH ; id++) { +SET_BOTH_CH_32 (dw, id, int_setup, +HDMA_V0_STOP_INT_MASK |HDMA_V0_ABORT_INT_MASK ); +SET_BOTH_CH_32 (dw, id, int_clear, +HDMA_V0_STOP_INT_MASK |HDMA_V0_ABORT_INT_MASK ); +SET_BOTH_CH_32 (dw, id, ch_en,0 ); + } +} + +static u16 dw_hdma_v0_core_ch_count (struct dw_edma *dw,enum dw_edma_dir dir) +{ +u32 num_ch =0 ; +int id; + +for (id =0 ; id <HDMA_V0_MAX_NR_CH ; id++) { +if (GET_CH_32 (dw, id, dir, ch_en) &BIT (0 )) + num_ch++; + } + +if (num_ch >HDMA_V0_MAX_NR_CH ) + num_ch =HDMA_V0_MAX_NR_CH ; + +return (u16 )num_ch; +} + +static enum dma_status dw_hdma_v0_core_ch_status (struct dw_edma_chan *chan) +{ +struct dw_edma *dw = chan->dw; +u32 tmp; + + tmp =FIELD_GET (HDMA_V0_CH_STATUS_MASK , +GET_CH_32 (dw, chan->id, chan->dir, ch_stat)); + +if (tmp ==1 ) +return DMA_IN_PROGRESS ; +else if (tmp ==3 ) +return DMA_COMPLETE ; +else +return DMA_ERROR ; +} + +static void dw_hdma_v0_core_clear_done_int (struct dw_edma_chan *chan) +{ +struct dw_edma *dw = chan->dw; + +SET_CH_32 (dw, chan->dir, chan->id, int_clear,HDMA_V0_STOP_INT_MASK ); +} + +static void dw_hdma_v0_core_clear_abort_int (struct dw_edma_chan *chan) +{ +struct dw_edma *dw = chan->dw; + +SET_CH_32 (dw, chan->dir, chan->id, int_clear,HDMA_V0_ABORT_INT_MASK ); +} + +static u32 dw_hdma_v0_core_status_int (struct dw_edma_chan *chan) +{ +struct dw_edma *dw = chan->dw; + +return GET_CH_32 (dw, chan->dir, chan->id, int_stat); +} + +static irqreturn_t +dw_hdma_v0_core_handle_int (struct dw_edma_irq *dw_irq,enum dw_edma_dir dir, +dw_edma_handler_t done,dw_edma_handler_t abort) +{ +struct dw_edma *dw = dw_irq->dw; +unsigned long total, pos, val; +irqreturn_t ret =IRQ_NONE ; +struct dw_edma_chan *chan; +unsigned long off, mask; + +if (dir ==EDMA_DIR_WRITE ) { + total = dw->wr_ch_cnt; + off =0 ; + mask = dw_irq->wr_mask; + }else { + total = dw->rd_ch_cnt; + off = dw->wr_ch_cnt; + mask = dw_irq->rd_mask; + } + +for_each_set_bit (pos, &mask, total) { + chan = &dw->chan[pos + off]; + + val =dw_hdma_v0_core_status_int (chan); +if (FIELD_GET (HDMA_V0_STOP_INT_MASK , val)) { +dw_hdma_v0_core_clear_done_int (chan); +done (chan); + + ret =IRQ_HANDLED ; + } + +if (FIELD_GET (HDMA_V0_ABORT_INT_MASK , val)) { +dw_hdma_v0_core_clear_abort_int (chan); +abort (chan); + + ret =IRQ_HANDLED ; + } + } + +return ret; +} + +static void dw_hdma_v0_write_ll_data (struct dw_edma_chunk *chunk,int i, +u32 control,u32 size,u64 sar,u64 dar) +{ +ptrdiff_t ofs = i *sizeof (struct dw_hdma_v0_lli ); + +if (chunk->chan->dw->chip->flags &DW_EDMA_CHIP_LOCAL ) { +struct dw_hdma_v0_lli *lli = chunk->ll_region.vaddr.mem + ofs; + + lli->control = control; + lli->transfer_size = size; + lli->sar.reg = sar; + lli->dar.reg = dar; + }else { +struct dw_hdma_v0_lli __iomem *lli = chunk->ll_region.vaddr.io + ofs; + +writel (control, &lli->control); +writel (size, &lli->transfer_size); +writeq (sar, &lli->sar.reg); +writeq (dar, &lli->dar.reg); + } +} + +static void dw_hdma_v0_write_ll_link (struct dw_edma_chunk *chunk, +int i,u32 control,u64 pointer) +{ +ptrdiff_t ofs = i *sizeof (struct dw_hdma_v0_lli ); + +if (chunk->chan->dw->chip->flags &DW_EDMA_CHIP_LOCAL ) { +struct dw_hdma_v0_llp *llp = chunk->ll_region.vaddr.mem + ofs; + + llp->control = control; + llp->llp.reg = pointer; + }else { +struct dw_hdma_v0_llp __iomem *llp = chunk->ll_region.vaddr.io + ofs; + +writel (control, &llp->control); +writeq (pointer, &llp->llp.reg); + } +} + +static void dw_hdma_v0_core_write_chunk (struct dw_edma_chunk *chunk) +{ +struct dw_edma_burst *child; +struct dw_edma_chan *chan = chunk->chan; +u32 control =0 , i =0 ; +int j; + +if (chunk->cb) + control =DW_HDMA_V0_CB ; + + j = chunk->bursts_alloc; +list_for_each_entry (child, &chunk->burst->list, list) { + j--; +if (!j) { + control |=DW_HDMA_V0_LIE ; +if (!(chan->dw->chip->flags &DW_EDMA_CHIP_LOCAL )) + control |=DW_HDMA_V0_RIE ; + } + +dw_hdma_v0_write_ll_data (chunk, i++, control, child->sz, + child->sar, child->dar); + } + + control =DW_HDMA_V0_LLP |DW_HDMA_V0_TCB ; +if (!chunk->cb) + control |=DW_HDMA_V0_CB ; + +dw_hdma_v0_write_ll_link (chunk, i, control, chunk->ll_region.paddr); +} + +static void dw_hdma_v0_core_start (struct dw_edma_chunk *chunk,bool first) +{ +struct dw_edma_chan *chan = chunk->chan; +struct dw_edma *dw = chan->dw; +u32 tmp; + +dw_hdma_v0_core_write_chunk (chunk); + +if (first) { +/* Enable engine */ +SET_CH_32 (dw, chan->dir, chan->id, ch_en,BIT (0 )); +/* Interrupt enable&unmask - done, abort */ + tmp =GET_CH_32 (dw, chan->dir, chan->id, int_setup) | +HDMA_V0_STOP_INT_MASK |HDMA_V0_ABORT_INT_MASK | +HDMA_V0_LOCAL_STOP_INT_EN |HDMA_V0_LOCAL_STOP_INT_EN ; +SET_CH_32 (dw, chan->dir, chan->id, int_setup, tmp); +/* Channel control */ +SET_CH_32 (dw, chan->dir, chan->id, control1,HDMA_V0_LINKLIST_EN ); +/* Linked list */ +/* llp is not aligned on 64bit -> keep 32bit accesses */ +SET_CH_32 (dw, chan->dir, chan->id, llp.lsb, +lower_32_bits (chunk->ll_region.paddr)); +SET_CH_32 (dw, chan->dir, chan->id, llp.msb, +upper_32_bits (chunk->ll_region.paddr)); + } +/* Set consumer cycle */ +SET_CH_32 (dw, chan->dir, chan->id, cycle_sync, +HDMA_V0_CONSUMER_CYCLE_STAT |HDMA_V0_CONSUMER_CYCLE_BIT ); +/* Doorbell */ +SET_CH_32 (dw, chan->dir, chan->id, doorbell,HDMA_V0_DOORBELL_START ); +} + +static void dw_hdma_v0_core_ch_config (struct dw_edma_chan *chan) +{ +struct dw_edma *dw = chan->dw; + +/* MSI done addr - low, high */ +SET_CH_32 (dw, chan->dir, chan->id, msi_stop.lsb, chan->msi.address_lo); +SET_CH_32 (dw, chan->dir, chan->id, msi_stop.msb, chan->msi.address_hi); +/* MSI abort addr - low, high */ +SET_CH_32 (dw, chan->dir, chan->id, msi_abort.lsb, chan->msi.address_lo); +SET_CH_32 (dw, chan->dir, chan->id, msi_abort.msb, chan->msi.address_hi); +/* config MSI data */ +SET_CH_32 (dw, chan->dir, chan->id, msi_msgdata, chan->msi.data); +} + +/* HDMA debugfs callbacks */ +static void dw_hdma_v0_core_debugfs_on (struct dw_edma *dw) +{ +} + +static const struct dw_edma_core_ops dw_hdma_v0_core = { + .off = dw_hdma_v0_core_off, + .ch_count = dw_hdma_v0_core_ch_count, + .ch_status = dw_hdma_v0_core_ch_status, + .handle_int = dw_hdma_v0_core_handle_int, + .start = dw_hdma_v0_core_start, + .ch_config = dw_hdma_v0_core_ch_config, + .debugfs_on = dw_hdma_v0_core_debugfs_on, +}; + +void dw_hdma_v0_core_register (struct dw_edma *dw) +{ + dw->core = &dw_hdma_v0_core; +}drivers/dma/dw-edma/dw-hdma-v0-core.h new file +17
-0@@ -0,0 +1,17 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Copyright (c) 2023 Cai Huoqing +* Synopsys DesignWare HDMA v0 core +* +* Author: Cai Huoqing <[email protected]> +*/ + +#ifndef _DW_HDMA_V0_CORE_H +#define _DW_HDMA_V0_CORE_H + +#include <linux/dma/edma.h> + +/* HDMA core register */ +void dw_hdma_v0_core_register (struct dw_edma *dw); + +#endif /* _DW_HDMA_V0_CORE_H */ drivers/dma/dw-edma/dw-hdma-v0-regs.h new file +129
-0@@ -0,0 +1,129 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Copyright (c) 2023 Cai Huoqing +* Synopsys DesignWare HDMA v0 reg +* +* Author: Cai Huoqing <[email protected]> +*/ + +#ifndef _DW_HDMA_V0_REGS_H +#define _DW_HDMA_V0_REGS_H + +#include <linux/dmaengine.h> + +#define HDMA_V0_MAX_NR_CH 8 +#define HDMA_V0_LOCAL_ABORT_INT_EN BIT(6) +#define HDMA_V0_REMOTE_ABORT_INT_EN BIT(5) +#define HDMA_V0_LOCAL_STOP_INT_EN BIT(4) +#define HDMA_V0_REMOTEL_STOP_INT_EN BIT(3) +#define HDMA_V0_ABORT_INT_MASK BIT(2) +#define HDMA_V0_STOP_INT_MASK BIT(0) +#define HDMA_V0_LINKLIST_EN BIT(0) +#define HDMA_V0_CONSUMER_CYCLE_STAT BIT(1) +#define HDMA_V0_CONSUMER_CYCLE_BIT BIT(0) +#define HDMA_V0_DOORBELL_START BIT(0) +#define HDMA_V0_CH_STATUS_MASK GENMASK(1, 0) + +struct dw_hdma_v0_ch_regs { +u32 ch_en;/* 0x0000 */ +u32 doorbell;/* 0x0004 */ +u32 prefetch;/* 0x0008 */ +u32 handshake;/* 0x000c */ +union { +u64 reg;/* 0x0010..0x0014 */ +struct { +u32 lsb;/* 0x0010 */ +u32 msb;/* 0x0014 */ + }; + } llp; +u32 cycle_sync;/* 0x0018 */ +u32 transfer_size;/* 0x001c */ +union { +u64 reg;/* 0x0020..0x0024 */ +struct { +u32 lsb;/* 0x0020 */ +u32 msb;/* 0x0024 */ + }; + } sar; +union { +u64 reg;/* 0x0028..0x002c */ +struct { +u32 lsb;/* 0x0028 */ +u32 msb;/* 0x002c */ + }; + } dar; +u32 watermark_en;/* 0x0030 */ +u32 control1;/* 0x0034 */ +u32 func_num;/* 0x0038 */ +u32 qos;/* 0x003c */ +u32 padding_1[16 ];/* 0x0040..0x007c */ +u32 ch_stat;/* 0x0080 */ +u32 int_stat;/* 0x0084 */ +u32 int_setup;/* 0x0088 */ +u32 int_clear;/* 0x008c */ +union { +u64 reg;/* 0x0090..0x0094 */ +struct { +u32 lsb;/* 0x0090 */ +u32 msb;/* 0x0094 */ + }; + } msi_stop; +union { +u64 reg;/* 0x0098..0x009c */ +struct { +u32 lsb;/* 0x0098 */ +u32 msb;/* 0x009c */ + }; + } msi_watermark; +union { +u64 reg;/* 0x00a0..0x00a4 */ +struct { +u32 lsb;/* 0x00a0 */ +u32 msb;/* 0x00a4 */ + }; + } msi_abort; +u32 msi_msgdata;/* 0x00a8 */ +u32 padding_2[21 ];/* 0x00ac..0x00fc */ +} __packed; + +struct dw_hdma_v0_ch { +struct dw_hdma_v0_ch_regs wr;/* 0x0000 */ +struct dw_hdma_v0_ch_regs rd;/* 0x0100 */ +} __packed; + +struct dw_hdma_v0_regs { +struct dw_hdma_v0_ch ch[HDMA_V0_MAX_NR_CH ];/* 0x0000..0x0fa8 */ +} __packed; + +struct dw_hdma_v0_lli { +u32 control; +u32 transfer_size; +union { +u64 reg; +struct { +u32 lsb; +u32 msb; + }; + } sar; +union { +u64 reg; +struct { +u32 lsb; +u32 msb; + }; + } dar; +} __packed; + +struct dw_hdma_v0_llp { +u32 control; +u32 reserved; +union { +u64 reg; +struct { +u32 lsb; +u32 msb; + }; + } llp; +} __packed; + +#endif /* _DW_HDMA_V0_REGS_H */ include/linux/dma/edma.h +2
-1@@ -48,7 +48,8 @@ struct dw_edma_plat_ops {enum dw_edma_map_format {EDMA_MF_EDMA_LEGACY =0x0 ,EDMA_MF_EDMA_UNROLL =0x1 , -EDMA_MF_HDMA_COMPAT =0x5 +EDMA_MF_HDMA_COMPAT =0x5 , +EDMA_MF_HDMA_NATIVE =0x7 , };/** Signature · 1 line
2.34.1
Signature · 1 line
மணிவண்ணன் சதாசிவம்
PATCH RESEND v9 4/4 dmaengine: dw-edma: Add HDMA DebugFS support
In reply to Cai HuoqingFrom: Cai huoqing <[email protected]>
Add HDMA DebugFS support to show registers content
---v8->v9:
1.Update commit log.
2.Remove unused macro
v8 link:
https://lore.kernel.org/lkml/[email protected]/
drivers/dma/dw-edma/Makefile | 3 +- drivers/dma/dw-edma/dw-hdma-v0-core.c | 2 + drivers/dma/dw-edma/dw-hdma-v0-debugfs.c | 170 +++++++++++++++++++++++ drivers/dma/dw-edma/dw-hdma-v0-debugfs.h | 22 +++ 4 files changed, 196 insertions(+), 1 deletion(-) create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.h
drivers/dma/dw-edma/Makefile +2 -1
@@ -1,7 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_DW_EDMA) += dw-edma.o -dw-edma-$(CONFIG_DEBUG_FS) := dw-edma-v0-debugfs.o +dw-edma-$(CONFIG_DEBUG_FS) := dw-edma-v0-debugfs.o \ + dw-hdma-v0-debugfs.o dw-edma-objs := dw-edma-core.o \ dw-edma-v0-core.o \ dw-hdma-v0-core.o $(dw-edma-y)
drivers/dma/dw-edma/dw-hdma-v0-core.c +2 -0
@@ -11,6 +11,7 @@#include "dw-edma-core.h" #include "dw-hdma-v0-core.h" #include "dw-hdma-v0-regs.h" +#include "dw-hdma-v0-debugfs.h" enum dw_hdma_control {DW_HDMA_V0_CB =BIT (0 ),
@@ -276,6 +277,7 @@ static void dw_hdma_v0_core_ch_config(struct dw_edma_chan *chan)/* HDMA debugfs callbacks */ static void dw_hdma_v0_core_debugfs_on (struct dw_edma *dw) { +dw_hdma_v0_debugfs_on (dw); }static const struct dw_edma_core_ops dw_hdma_v0_core = {
drivers/dma/dw-edma/dw-hdma-v0-debugfs.c new file +170 -0
170 lines not on this page · raw message
drivers/dma/dw-edma/dw-hdma-v0-debugfs.h new file +22 -0
@@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Copyright (c) 2023 Cai Huoqing +* Synopsys DesignWare HDMA v0 debugfs +* +* Author: Cai Huoqing <[email protected]> +*/ + +#ifndef _DW_HDMA_V0_DEBUG_FS_H +#define _DW_HDMA_V0_DEBUG_FS_H + +#include <linux/dma/edma.h> + +#ifdef CONFIG_DEBUG_FS +void dw_hdma_v0_debugfs_on (struct dw_edma *dw); +#else +static inline void dw_hdma_v0_debugfs_on (struct dw_edma *dw) +{ +} +#endif /* CONFIG_DEBUG_FS */ + +#endif /* _DW_HDMA_V0_DEBUG_FS_H */
Signature · 1 line
2.34.1
Re: [PATCH RESEND v9 4/4] dmaengine: dw-edma: Add HDMA DebugFS support
Quoted 5 lines · Cai Huoqing
From: Cai huoqing <[email protected]>
Add HDMA DebugFS support to show registers content
Signed-off-by Cai huoqing <[email protected]>
- Mani
Quoted 258 lines
Reviewed-by Serge Semin <[email protected]>---
v8->v9:
1.Update commit log.
2.Remove unused macrov8 link:
https://lore.kernel.org/lkml/[email protected]/drivers/dma/dw-edma/Makefile | 3 +- drivers/dma/dw-edma/dw-hdma-v0-core.c | 2 + drivers/dma/dw-edma/dw-hdma-v0-debugfs.c | 170 +++++++++++++++++++++++ drivers/dma/dw-edma/dw-hdma-v0-debugfs.h | 22 +++ 4 files changed, 196 insertions(+), 1 deletion(-) create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.hdrivers/dma/dw-edma/Makefile +2
-1@@ -1,7 +1,8 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_DW_EDMA) += dw-edma.o -dw-edma-$(CONFIG_DEBUG_FS) := dw-edma-v0-debugfs.o +dw-edma-$(CONFIG_DEBUG_FS) := dw-edma-v0-debugfs.o \ + dw-hdma-v0-debugfs.o dw-edma-objs := dw-edma-core.o \ dw-edma-v0-core.o \ dw-hdma-v0-core.o $(dw-edma-y)drivers/dma/dw-edma/dw-hdma-v0-core.c +2
-0@@ -11,6 +11,7 @@#include "dw-edma-core.h" #include "dw-hdma-v0-core.h" #include "dw-hdma-v0-regs.h" +#include "dw-hdma-v0-debugfs.h" enum dw_hdma_control {DW_HDMA_V0_CB =BIT (0 ),@@ -276,6 +277,7 @@ static void dw_hdma_v0_core_ch_config(struct dw_edma_chan *chan)/* HDMA debugfs callbacks */ static void dw_hdma_v0_core_debugfs_on (struct dw_edma *dw) { +dw_hdma_v0_debugfs_on (dw); }static const struct dw_edma_core_ops dw_hdma_v0_core = {drivers/dma/dw-edma/dw-hdma-v0-debugfs.c new file +170
-0@@ -0,0 +1,170 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Copyright (c) 2023 Cai Huoqing +* Synopsys DesignWare HDMA v0 debugfs +* +* Author: Cai Huoqing <[email protected]> +*/ + +#include <linux/debugfs.h> +#include <linux/bitfield.h> + +#include "dw-hdma-v0-debugfs.h" +#include "dw-hdma-v0-regs.h" +#include "dw-edma-core.h" + +#define REGS_ADDR (dw, name) \ + ({ \ + struct dw_hdma_v0_regs __iomem *__regs = (dw)->chip->reg_base; \ + \ + (void __iomem *)&__regs->name; \ + }) + +#define REGS_CH_ADDR (dw, name, _dir, _ch) \ + ({ \ + struct dw_hdma_v0_ch_regs __iomem *__ch_regs; \ + \ + if (_dir == EDMA_DIR_READ) \ + __ch_regs = REGS_ADDR(dw, ch[_ch].rd); \ + else \ + __ch_regs = REGS_ADDR(dw, ch[_ch].wr); \ + \ + (void __iomem *)&__ch_regs->name; \ + }) + +#define CTX_REGISTER (dw, name, dir, ch) \ + {#name, REGS_CH_ADDR(dw, name, dir, ch)} + +#define WRITE_STR "write" +#define READ_STR "read" +#define CHANNEL_STR "channel" +#define REGISTERS_STR "registers" + +struct dw_hdma_debugfs_entry { +const char *name; +void __iomem *reg; +}; + +static int dw_hdma_debugfs_u32_get (void *data,u64 *val) +{ +struct dw_hdma_debugfs_entry *entry = data; +void __iomem *reg = entry->reg; + + *val =readl (reg); + +return 0 ; +} +DEFINE_DEBUGFS_ATTRIBUTE (fops_x32, dw_hdma_debugfs_u32_get,NULL ,"0x%08llx\n" ); + +static void dw_hdma_debugfs_create_x32 (struct dw_edma *dw, +const struct dw_hdma_debugfs_entry ini[], +int nr_entries,struct dentry *dent) +{ +struct dw_hdma_debugfs_entry *entries; +int i; + + entries =devm_kcalloc (dw->chip->dev, nr_entries,sizeof (*entries), +GFP_KERNEL ); +if (!entries) +return ; + +for (i =0 ; i < nr_entries; i++) { + entries[i] = ini[i]; + +debugfs_create_file_unsafe (entries[i].name,0444 , dent, + &entries[i], &fops_x32); + } +} + +static void dw_hdma_debugfs_regs_ch (struct dw_edma *dw,enum dw_edma_dir dir, +u16 ch,struct dentry *dent) +{ +const struct dw_hdma_debugfs_entry debugfs_regs[] = { +CTX_REGISTER (dw, ch_en, dir, ch), +CTX_REGISTER (dw, doorbell, dir, ch), +CTX_REGISTER (dw, prefetch, dir, ch), +CTX_REGISTER (dw, handshake, dir, ch), +CTX_REGISTER (dw, llp.lsb, dir, ch), +CTX_REGISTER (dw, llp.msb, dir, ch), +CTX_REGISTER (dw, cycle_sync, dir, ch), +CTX_REGISTER (dw, transfer_size, dir, ch), +CTX_REGISTER (dw, sar.lsb, dir, ch), +CTX_REGISTER (dw, sar.msb, dir, ch), +CTX_REGISTER (dw, dar.lsb, dir, ch), +CTX_REGISTER (dw, dar.msb, dir, ch), +CTX_REGISTER (dw, watermark_en, dir, ch), +CTX_REGISTER (dw, control1, dir, ch), +CTX_REGISTER (dw, func_num, dir, ch), +CTX_REGISTER (dw, qos, dir, ch), +CTX_REGISTER (dw, ch_stat, dir, ch), +CTX_REGISTER (dw, int_stat, dir, ch), +CTX_REGISTER (dw, int_setup, dir, ch), +CTX_REGISTER (dw, int_clear, dir, ch), +CTX_REGISTER (dw, msi_stop.lsb, dir, ch), +CTX_REGISTER (dw, msi_stop.msb, dir, ch), +CTX_REGISTER (dw, msi_watermark.lsb, dir, ch), +CTX_REGISTER (dw, msi_watermark.msb, dir, ch), +CTX_REGISTER (dw, msi_abort.lsb, dir, ch), +CTX_REGISTER (dw, msi_abort.msb, dir, ch), +CTX_REGISTER (dw, msi_msgdata, dir, ch), + }; +int nr_entries =ARRAY_SIZE (debugfs_regs); + +dw_hdma_debugfs_create_x32 (dw, debugfs_regs, nr_entries, dent); +} + +static void dw_hdma_debugfs_regs_wr (struct dw_edma *dw,struct dentry *dent) +{ +struct dentry *regs_dent, *ch_dent; +char name[16 ]; +int i; + + regs_dent =debugfs_create_dir (WRITE_STR , dent); + +for (i =0 ; i < dw->wr_ch_cnt; i++) { +snprintf (name,sizeof (name),"%s:%d" ,CHANNEL_STR , i); + + ch_dent =debugfs_create_dir (name, regs_dent); + +dw_hdma_debugfs_regs_ch (dw,EDMA_DIR_WRITE , i, ch_dent); + } +} + +static void dw_hdma_debugfs_regs_rd (struct dw_edma *dw,struct dentry *dent) +{ +struct dentry *regs_dent, *ch_dent; +char name[16 ]; +int i; + + regs_dent =debugfs_create_dir (READ_STR , dent); + +for (i =0 ; i < dw->rd_ch_cnt; i++) { +snprintf (name,sizeof (name),"%s:%d" ,CHANNEL_STR , i); + + ch_dent =debugfs_create_dir (name, regs_dent); + +dw_hdma_debugfs_regs_ch (dw,EDMA_DIR_READ , i, ch_dent); + } +} + +static void dw_hdma_debugfs_regs (struct dw_edma *dw) +{ +struct dentry *regs_dent; + + regs_dent =debugfs_create_dir (REGISTERS_STR , dw->dma.dbg_dev_root); + +dw_hdma_debugfs_regs_wr (dw, regs_dent); +dw_hdma_debugfs_regs_rd (dw, regs_dent); +} + +void dw_hdma_v0_debugfs_on (struct dw_edma *dw) +{ +if (!debugfs_initialized ()) +return ; + +debugfs_create_u32 ("mf" ,0444 , dw->dma.dbg_dev_root, &dw->chip->mf); +debugfs_create_u16 ("wr_ch_cnt" ,0444 , dw->dma.dbg_dev_root, &dw->wr_ch_cnt); +debugfs_create_u16 ("rd_ch_cnt" ,0444 , dw->dma.dbg_dev_root, &dw->rd_ch_cnt); + +dw_hdma_debugfs_regs (dw); +}drivers/dma/dw-edma/dw-hdma-v0-debugfs.h new file +22
-0@@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Copyright (c) 2023 Cai Huoqing +* Synopsys DesignWare HDMA v0 debugfs +* +* Author: Cai Huoqing <[email protected]> +*/ + +#ifndef _DW_HDMA_V0_DEBUG_FS_H +#define _DW_HDMA_V0_DEBUG_FS_H + +#include <linux/dma/edma.h> + +#ifdef CONFIG_DEBUG_FS +void dw_hdma_v0_debugfs_on (struct dw_edma *dw); +#else +static inline void dw_hdma_v0_debugfs_on (struct dw_edma *dw) +{ +} +#endif /* CONFIG_DEBUG_FS */ + +#endif /* _DW_HDMA_V0_DEBUG_FS_H */ Signature · 1 line
2.34.1
Signature · 1 line
மணிவண்ணன் சதாசிவம்
Quoted 15 lines · Cai Huoqing
Add support for HDMA NATIVE, as long the IP design has set the compatible register map parameter-HDMA_NATIVE, which allows compatibility for native HDMA register configuration.
The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP. And the native HDMA registers are different from eDMA,
so this patch add support for HDMA NATIVE mode.HDMA write and read channels operate independently to maximize the performance of the HDMA read and write data transfer over the link When you configure the HDMA with multiple read channels, then it uses a round robin (RR) arbitration scheme to select the next read channel to be serviced.The same applies when youhave multiple write channels.
Quoted 4 lines
The native HDMA driver also supports a maximum of 16 independent channels (8 write + 8 read), which can run simultaneously. Both SAR (Source Address Register) and DAR (Destination Address Register) are aligned to byte.
Hi Vinod,
thanks for your reply,
these resend patchs base on dmaengine-next.
please try it.
Thanks,
Cai-
Quoted 46 lines
Cai Huoqing (1):
dmaengine: dw-edma: Add support for native HDMACai huoqing (3):
dmaengine: dw-edma: Renamedw_edma_core_opsstructure to
dw_edma_plat_ops
dmaengine: dw-edma: Create a newdw_edma_core_opsstructure to
abstract controller operation
dmaengine: dw-edma: Add HDMA DebugFS supportTested-by Serge Semin <[email protected]>
v8->v9:
[3/4]
1.Drop an empty line.
[4/4]
2.Update commit log.
3.Remove unused macrov8 link:
https://lore.kernel.org/lkml/[email protected]/drivers/dma/dw-edma/Makefile | 8 +- drivers/dma/dw-edma/dw-edma-core.c | 86 ++---- drivers/dma/dw-edma/dw-edma-core.h | 58 ++++ drivers/dma/dw-edma/dw-edma-pcie.c | 4 +- drivers/dma/dw-edma/dw-edma-v0-core.c | 85 +++++- drivers/dma/dw-edma/dw-edma-v0-core.h | 14 +- drivers/dma/dw-edma/dw-hdma-v0-core.c | 296 +++++++++++++++++++ drivers/dma/dw-edma/dw-hdma-v0-core.h | 17 ++ drivers/dma/dw-edma/dw-hdma-v0-debugfs.c | 170 +++++++++++ drivers/dma/dw-edma/dw-hdma-v0-debugfs.h | 22 ++ drivers/dma/dw-edma/dw-hdma-v0-regs.h | 129 ++++++++ drivers/pci/controller/dwc/pcie-designware.c | 2 +- include/linux/dma/edma.h | 7 +- 13 files changed, 807 insertions(+), 91 deletions(-) create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.h create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.h create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-regs.hSignature · 1 line
2.34.1
Quoted 23 lines · Cai Huoqing
Add support for HDMA NATIVE, as long the IP design has set the compatible register map parameter-HDMA_NATIVE, which allows compatibility for native HDMA register configuration.
The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP. And the native HDMA registers are different from eDMA,
so this patch add support for HDMA NATIVE mode.HDMA write and read channels operate independently to maximize the performance of the HDMA read and write data transfer over the link When you configure the HDMA with multiple read channels, then it uses a round robin (RR) arbitration scheme to select the next read channel to be serviced.The same applies when youhave multiple write channels.
The native HDMA driver also supports a maximum of 16 independent channels (8 write + 8 read), which can run simultaneously. Both SAR (Source Address Register) and DAR (Destination Address Register) are aligned to byte.
Cai Huoqing (1):
dmaengine: dw-edma: Add support for native HDMA
Quoted 8 lines
Cai huoqing (3):
dmaengine: dw-edma: Renamedw_edma_core_opsstructure to
dw_edma_plat_ops
dmaengine: dw-edma: Create a newdw_edma_core_opsstructure to
abstract controller operation
dmaengine: dw-edma: Add HDMA DebugFS supportTested-by Serge Semin <[email protected]>
Two small notes in the regard of the resubmitted series:
1. On resubmission it would be nice to move the Tested-by tag to all the patches of the series. Currently neither b4 tool nor patchwork see it which may cause the tag missing should @Vinod apply the patch by using these utilities and if he didn't notice it in the cover-letter.
2. Each resubmission even with no functional change implies patchset version advance. So this patchset was supposed to be v10 with the changelog describing that it was rebased onto the latest dmaengine-next branch state.
Just to make sure that my tag won't be missing should this series be applied:
-Serge(y)
Quoted 34 lines
v8->v9:
[3/4]
1.Drop an empty line.
[4/4]
2.Update commit log.
3.Remove unused macrov8 link:
https://lore.kernel.org/lkml/[email protected]/drivers/dma/dw-edma/Makefile | 8 +- drivers/dma/dw-edma/dw-edma-core.c | 86 ++---- drivers/dma/dw-edma/dw-edma-core.h | 58 ++++ drivers/dma/dw-edma/dw-edma-pcie.c | 4 +- drivers/dma/dw-edma/dw-edma-v0-core.c | 85 +++++- drivers/dma/dw-edma/dw-edma-v0-core.h | 14 +- drivers/dma/dw-edma/dw-hdma-v0-core.c | 296 +++++++++++++++++++ drivers/dma/dw-edma/dw-hdma-v0-core.h | 17 ++ drivers/dma/dw-edma/dw-hdma-v0-debugfs.c | 170 +++++++++++ drivers/dma/dw-edma/dw-hdma-v0-debugfs.h | 22 ++ drivers/dma/dw-edma/dw-hdma-v0-regs.h | 129 ++++++++ drivers/pci/controller/dwc/pcie-designware.c | 2 +- include/linux/dma/edma.h | 7 +- 13 files changed, 807 insertions(+), 91 deletions(-) create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.h create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.h create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-regs.hSignature · 1 line
2.34.1
Quoted 23 lines · Cai Huoqing
Add support for HDMA NATIVE, as long the IP design has set the compatible register map parameter-HDMA_NATIVE, which allows compatibility for native HDMA register configuration.
The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP. And the native HDMA registers are different from eDMA,
so this patch add support for HDMA NATIVE mode.HDMA write and read channels operate independently to maximize the performance of the HDMA read and write data transfer over the link When you configure the HDMA with multiple read channels, then it uses a round robin (RR) arbitration scheme to select the next read channel to be serviced.The same applies when youhave multiple write channels.
The native HDMA driver also supports a maximum of 16 independent channels (8 write + 8 read), which can run simultaneously. Both SAR (Source Address Register) and DAR (Destination Address Register) are aligned to byte.
Cai Huoqing (1):
dmaengine: dw-edma: Add support for native HDMA
Quoted 8 lines
Cai huoqing (3):
dmaengine: dw-edma: Renamedw_edma_core_opsstructure to
dw_edma_plat_ops
dmaengine: dw-edma: Create a newdw_edma_core_opsstructure to
abstract controller operation
dmaengine: dw-edma: Add HDMA DebugFS supportTested-by Serge Semin <[email protected]>
Hi Vinod
Just ping this patch.
I have rebased this patch series, pls try it.
Thanks,
-Cai
Quoted 34 lines
v8->v9:
[3/4]
1.Drop an empty line.
[4/4]
2.Update commit log.
3.Remove unused macrov8 link:
https://lore.kernel.org/lkml/[email protected]/drivers/dma/dw-edma/Makefile | 8 +- drivers/dma/dw-edma/dw-edma-core.c | 86 ++---- drivers/dma/dw-edma/dw-edma-core.h | 58 ++++ drivers/dma/dw-edma/dw-edma-pcie.c | 4 +- drivers/dma/dw-edma/dw-edma-v0-core.c | 85 +++++- drivers/dma/dw-edma/dw-edma-v0-core.h | 14 +- drivers/dma/dw-edma/dw-hdma-v0-core.c | 296 +++++++++++++++++++ drivers/dma/dw-edma/dw-hdma-v0-core.h | 17 ++ drivers/dma/dw-edma/dw-hdma-v0-debugfs.c | 170 +++++++++++ drivers/dma/dw-edma/dw-hdma-v0-debugfs.h | 22 ++ drivers/dma/dw-edma/dw-hdma-v0-regs.h | 129 ++++++++ drivers/pci/controller/dwc/pcie-designware.c | 2 +- include/linux/dma/edma.h | 7 +- 13 files changed, 807 insertions(+), 91 deletions(-) create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.h create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.c create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.h create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-regs.hSignature · 1 line
2.34.1