Add Ethernet driver for StarFive JH7110 SoC
Subsystems (7)
v12 cover Add Ethernet driver for StarFive JH7110 SoC
This series adds ethernet support for the StarFive JH7110 RISC-V SoC, which includes a dwmac-5.20 MAC driver (from Synopsys DesignWare). This series has been tested and works fine on VisionFive-2 v1.2A and v1.3B SBC boards.
For more information and support, you can visit RVspace wiki[1]. You can simply review or test the patches at the link [2]. This patchset should be applied after the patchset [3] [4].
[1]: https://wiki.rvspace.org/
[2]: https://github.com/saminGuo/linux/tree/vf2-6.3rc4-gmac-net-next
[3]: https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]
[4]: https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]
Changes since v11:
Patch 6:
- Renamed patch header to "net: stmmac: dwmac-starfive:xxx" (by Emil)
- Fixed misleading error message (by Emil)
Changes history:
Changes since v10:
Patch 4:
- Required goes after properties (by Krzysztof Kozlowski) Patch 5:
- Fixed the wrong binding filename (by Conor Dooley)
Changes since v9:
- Rebased on tag v6.3-rc4.
Patch 5:
- Cleaned up all the error handling code by dev_err_probe (by Emil).
- Fixed the warning that clang uses W=1 because 'rate' may not be initialized (by Jakub Kicinski)
Changes since v8:
Patch 4:
- Dropped irrelevant MAINTAINERS context (by Jakub Kicinski)
Patch 6:
- Moved error messages to starfive_dwmac_set_mode function to avoid getting error messages twice when syscon_regmap_lookup_by_phandle_args fails. (by Emil)
Changes since v7:
Patch 4:
- Constrained the reg/interrupts/interrupt-names properties (by Krzysztof Kozlowski)
Changes since v6:
- Sended network patches[patch 1,2,3,4,5,6] and riscv trees patches[patch 7,8] separately (by Jakub Kicinski)
Changes since v5:
- Dropped "depends on STMMAC_ETH" and compiled DWMAC_STARFIVE to m by default (by Emil)
- Removed clk_gtx in struct starfive_dwmac due to this pointer is only set, but never read. (by Emil)
- Only setting the plat_dat->fix_mac_speed callback when it is needed (by Emil)
- Moved mdio/phy nodes from SOC .dtsi into board .dtsi (by Andrew)
- Modified the parameters passed by starfive,syscon (by Andrew && Emil)
<syscon, offset, mask> ==> <syscon, offset, shift>
- Optimized the patchs(Fewer patches from 12 to 8)
1)merged patch-7 into patch-4 (by Rob)
2)merged patch-9 into patch-5
2)merged patch-11,12 into patch-10
3)Adjusted the patchs order
- Fixed the unevaluatedProperties property from true to false (by Rob)
- Replaced contains:enum with items:const for reset-names in snps,dwmac.yaml (by Rob)
- Tested-by: Tommaso Merciai <[email protected]>
Changes since v4:
- Supported both visionfive 2 v1.2A and visionfive 2 v1.3B.
- Reworded the maxitems number of resets property in 'snps,dwmac.yaml'.
- Suggested by Emil, dropped the _PLAT/_plat from the config/function/struct/file names.
- Suggested by Emil, added MODULE_DEVICE_TABLE().
- Suggested by Emil, dropped clk_gtxclk and use clk_tx_inv to set the clock frequency.
- Added phy interface mode configuration function.
- Rebased on tag v6.2.
Changes since v3:
- Reworded the maxitems number of resets property in 'snps,dwmac.yaml'
- Removed the unused code in 'dwmac-starfive-plat.c'.
- Reworded the return statement in 'starfive_eth_plat_fix_mac_speed' function.
Changes since v2:
- Renamed the dt-bindings 'starfive,jh71x0-dwmac.yaml' to 'starfive,jh7110-dwmac.yaml'.
- Reworded the commit messages.
- Reworded the example context in the dt-binding 'starfive,jh7110-dwmac.yaml'.
- Removed "starfive,jh7100-dwmac" compatible string and special initialization of jh7100.
- Removed the parts of YT8531,so dropped patch 5 and 6.
- Reworded the maxitems number of resets property in 'snps,dwmac.yaml'.
Changes since v1:
- Recovered the author of the 1st and 3rd patches back to Emil Renner Berthing.
- Added a new patch to update maxitems number of resets property in 'snps,dwmac.yaml'.
- Fixed the check errors reported by "make dt_binding_check".
- Renamed the dt-binding 'starfive,dwmac-plat.yaml' to 'starfive,jh71x0-dwmac.yaml'.
- Updated the example context in the dt-binding 'starfive,jh71x0-dwmac.yaml'.
- Added new dt-binding 'motorcomm,yt8531.yaml' to describe details of phy clock delay configuration parameters.
- Added more comments for PHY driver setting. For more details, see 'motorcomm,yt8531.yaml'.
- Moved mdio device tree node from 'jh7110-starfive-visionfive-v2.dts' to 'jh7110.dtsi'.
- Re-worded the commit message of several patches.
- Renamed all the functions with starfive_eth_plat prefix in 'dwmac-starfive-plat.c'.
- Added "starfive,jh7100-dwmac" compatible string and special init to support JH7100.
Previous versions:
v1 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
v2 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
v3 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
v4 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
v5 - https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/
v6 - https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/
v7 - https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/
v8 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
v9 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
v10 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
v11 - https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
Emil Renner Berthing (2):
dt-bindings: net: snps,dwmac: Add dwmac-5.20 version
net: stmmac: platform: Add snps,dwmac-5.20 IP compatible string
Samin Guo (3):
dt-bindings: net: snps,dwmac: Add 'ahb' reset/reset-name
net: stmmac: Add glue layer for StarFive JH7110 SoC
net: stmmac: dwmac-starfive: Add phy interface settings
Yanhong Wang (1):
dt-bindings: net: Add support StarFive dwmac
.../devicetree/bindings/net/snps,dwmac.yaml | 17 +- .../bindings/net/starfive,jh7110-dwmac.yaml | 144 +++++++++++++++ MAINTAINERS | 7 + drivers/net/ethernet/stmicro/stmmac/Kconfig | 12 ++ drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + .../ethernet/stmicro/stmmac/dwmac-starfive.c | 171 ++++++++++++++++++ .../ethernet/stmicro/stmmac/stmmac_platform.c | 3 +- 7 files changed, 350 insertions(+), 5 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c
base-commit: 522c3534e9e1123cd03999016b08ce811058dfe0
prerequisite-patch-id: 55390537360f25c8b9cbfdc30b73ade004f436f7
prerequisite-patch-id: bb939c0c7c26b08addfccd890f9d3974b6eaec53
prerequisite-patch-id: 8a6f135bcabdad4a4bfb21f0c6a0ffd2bb57efe7
prerequisite-patch-id: c2366f993a9d85e28c06d8d09f064dd5e8b29a61
prerequisite-patch-id: 50d53a21f91f4087fc80b6f1f72864adfb0002b9
prerequisite-patch-id: 0df3703af91c30f1ca2c47f5609012f2d7200028
prerequisite-patch-id: 89f049f951e5acf75aab92541992f816fd0acc0d
prerequisite-patch-id: 551fae54377090044c3612fca9740a9b359abdd2
prerequisite-patch-id: c7fdf904f398d478f0ed6d57eb878982bc73329d
prerequisite-patch-id: 1b2d0982b18da060c82134f05bf3ce16425bac8d
prerequisite-patch-id: 090ba4b78d47bc19204916e76fdbc70021785388
prerequisite-patch-id: a5d9e0f7d4f8163f566678894cf693015119f2d9
prerequisite-patch-id: 4637a8fa2334a45fa6b64351f4e9e28d3e2d60d3
prerequisite-patch-id: 32647ec60a3b614e1c59ec8e54cb511ae832c22f
prerequisite-patch-id: aa06658ecf89c92d0dfdd6a4ba6d9e6e67532971
prerequisite-patch-id: 258ea5f9b8bf41b6981345dcc81795f25865d38f
prerequisite-patch-id: 8b6f2c9660c0ac0ee4e73e4c21aca8e6b75e81b9
prerequisite-patch-id: dbb0c0151b8bdf093e6ce79fd2fe3f60791a6e0b
prerequisite-patch-id: e7773c977a7b37692e9792b21cc4f17fa58f9215
prerequisite-patch-id: d57e95d31686772abc4c4d5aa1cadc344dc293cd
prerequisite-patch-id: 9f911969d0a550648493952c99096d26e05d4d83
prerequisite-patch-id: 41eddeabff082d08a76d8da523f90da4b5218d28
prerequisite-patch-id: 999c243dca89d56d452aa52ea3e181358b5c1d80
prerequisite-patch-id: 1be0fb49e0fbe293ca8fa94601e191b13c8c67d9
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
PATCH v12 1/6 dt-bindings: net: snps,dwmac: Add dwmac-5.20 version
From: Emil Renner Berthing <[email protected]>
Add dwmac-5.20 IP version to snps.dwmac.yaml
--- Documentation/devicetree/bindings/net/snps,dwmac.yaml | 4 ++++ 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/net/snps,dwmac.yaml +4 -0
@@ -30,6 +30,7 @@ select: - snps,dwmac-4.10a - snps,dwmac-4.20a - snps,dwmac-5.10a + - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10
@@ -87,6 +88,7 @@ properties: - snps,dwmac-4.10a - snps,dwmac-4.20a - snps,dwmac-5.10a + - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10
@@ -575,6 +577,7 @@ allOf: - snps,dwmac-3.50a - snps,dwmac-4.10a - snps,dwmac-4.20a + - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10 - st,spear600-gmac
@@ -629,6 +632,7 @@ allOf: - snps,dwmac-4.10a - snps,dwmac-4.20a - snps,dwmac-5.10a + - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10 - st,spear600-gmac
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
PATCH v12 2/6 net: stmmac: platform: Add snps,dwmac-5.20 IP compatible string
In reply to Samin GuoFrom: Emil Renner Berthing <[email protected]>
Add "snps,dwmac-5.20" compatible string for 5.20 version that can avoid to define some platform data in the glue layer.
--- drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +2 -1
@@ -519,7 +519,8 @@ stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac)if (of_device_is_compatible (np,"snps,dwmac-4.00" ) ||of_device_is_compatible (np,"snps,dwmac-4.10a" ) ||of_device_is_compatible (np,"snps,dwmac-4.20a" ) || -of_device_is_compatible (np,"snps,dwmac-5.10a" )) { +of_device_is_compatible (np,"snps,dwmac-5.10a" ) || +of_device_is_compatible (np,"snps,dwmac-5.20" )) { plat->has_gmac4 =1 ; plat->has_gmac =0 ; plat->pmt =1 ;
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
PATCH v12 3/6 dt-bindings: net: snps,dwmac: Add 'ahb' reset/reset-name
In reply to Samin GuoAccording to:stmmac_platform.c: stmmac_probe_config_dtstmmac_main.c: stmmac_dvr_probe
dwmac controller may require one (stmmaceth) or two (stmmaceth+ahb) reset signals, and the maxItems of resets/reset-names is going to be 2.
The gmac of Starfive Jh7110 SOC must have two resets. it uses snps,dwmac-5.20 IP.
--- .../devicetree/bindings/net/snps,dwmac.yaml | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-)
Documentation/devicetree/bindings/net/snps,dwmac.yaml +8 -4
@@ -133,12 +133,16 @@ properties: - ptp_ref resets: - maxItems: 1 - description: - MAC Reset signal. + minItems: 1 + items: + - description: GMAC stmmaceth reset + - description: AHB reset reset-names: - const: stmmaceth + minItems: 1 + items: + - const: stmmaceth + - const: ahb power-domains: maxItems: 1
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
PATCH v12 4/6 dt-bindings: net: Add support StarFive dwmac
In reply to Samin GuoFrom: Yanhong Wang <[email protected]>
Add documentation to describe StarFive dwmac driver(GMAC).
--- .../devicetree/bindings/net/snps,dwmac.yaml | 1 + .../bindings/net/starfive,jh7110-dwmac.yaml | 144 ++++++++++++++++++ MAINTAINERS | 6 + 3 files changed, 151 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml
Documentation/devicetree/bindings/net/snps,dwmac.yaml +1 -0
@@ -91,6 +91,7 @@ properties: - snps,dwmac-5.20 - snps,dwxgmac - snps,dwxgmac-2.10 + - starfive,jh7110-dwmac reg: minItems: 1
Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml new file +144 -0
144 lines not on this page · raw message
MAINTAINERS +6 -0
@@ -19905,6 +19905,12 @@ M: Emil Renner Berthing <[email protected]> S: Maintained F: arch/riscv/boot/dts/starfive/ +STARFIVE DWMAC GLUE LAYER +M: Emil Renner Berthing <[email protected]> +M: Samin Guo <[email protected]> +S: Maintained +F: Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml + STARFIVE JH7100 CLOCK DRIVERS M: Emil Renner Berthing <[email protected]> S: Maintained
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
PATCH v12 5/6 net: stmmac: Add glue layer for StarFive JH7110 SoC
In reply to Samin GuoThis adds StarFive dwmac driver support on the StarFive JH7110 SoC.
--- MAINTAINERS | 1 + drivers/net/ethernet/stmicro/stmmac/Kconfig | 12 ++ drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + .../ethernet/stmicro/stmmac/dwmac-starfive.c | 123 ++++++++++++++++++ 4 files changed, 137 insertions(+) create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c
MAINTAINERS +1 -0
@@ -19910,6 +19910,7 @@ M: Emil Renner Berthing <[email protected]> M: Samin Guo <[email protected]> S: Maintained F: Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml +F: drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c STARFIVE JH7100 CLOCK DRIVERS M: Emil Renner Berthing <[email protected]>
drivers/net/ethernet/stmicro/stmmac/Kconfig +12 -0
@@ -165,6 +165,18 @@ config DWMAC_SOCFPGA for the stmmac device driver. This driver is used for arria5 and cyclone5 FPGA SoCs. +config DWMAC_STARFIVE + tristate "StarFive dwmac support" + depends on OF && (ARCH_STARFIVE || COMPILE_TEST) + select MFD_SYSCON + default m if ARCH_STARFIVE + help + Support for ethernet controllers on StarFive RISC-V SoCs + + This selects the StarFive platform specific glue layer support for + the stmmac device driver. This driver is used for StarFive JH7110 + ethernet controller. + config DWMAC_STI tristate "STi GMAC support" default ARCH_STI
drivers/net/ethernet/stmicro/stmmac/Makefile +1 -0
@@ -23,6 +23,7 @@ obj-$(CONFIG_DWMAC_OXNAS) += dwmac-oxnas.o obj-$(CONFIG_DWMAC_QCOM_ETHQOS) += dwmac-qcom-ethqos.o obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o +obj-$(CONFIG_DWMAC_STARFIVE) += dwmac-starfive.o obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o obj-$(CONFIG_DWMAC_STM32) += dwmac-stm32.o obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c new file +123 -0
123 lines not on this page · raw message
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
PATCH v12 6/6 net: stmmac: dwmac-starfive: Add phy interface settings
In reply to Samin Guodwmac supports multiple modess. When working under rmii and rgmii, you need to set different phy interfaces.
According to the dwmac document, when working in rmii, it needs to be set to 0x4, and rgmii needs to be set to 0x1.
The phy interface needs to be set in syscon, the format is as follows:
starfive,syscon: <&syscon, offset, shift>
--- .../ethernet/stmicro/stmmac/dwmac-starfive.c | 48 +++++++++++++++++++ 1 file changed, 48 insertions(+)
drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c +48 -0
@@ -13,6 +13,10 @@#include "stmmac_platform.h" +#define STARFIVE_DWMAC_PHY_INFT_RGMII 0x1 +#define STARFIVE_DWMAC_PHY_INFT_RMII 0x4 +#define STARFIVE_DWMAC_PHY_INFT_FIELD 0x7U +struct starfive_dwmac {struct device *dev;struct clk *clk_tx;
@@ -46,6 +50,46 @@ static void starfive_dwmac_fix_mac_speed(void *priv, unsigned int speed)dev_err (dwmac->dev,"failed to set tx rate %lu\n" , rate); } +static int starfive_dwmac_set_mode (struct plat_stmmacenet_data *plat_dat) +{ +struct starfive_dwmac *dwmac = plat_dat->bsp_priv; +struct regmap *regmap; +unsigned int args[2 ]; +unsigned int mode; +int err; + +switch (plat_dat->interface) { +case PHY_INTERFACE_MODE_RMII : + mode =STARFIVE_DWMAC_PHY_INFT_RMII ; +break ; + +case PHY_INTERFACE_MODE_RGMII : +case PHY_INTERFACE_MODE_RGMII_ID : + mode =STARFIVE_DWMAC_PHY_INFT_RGMII ; +break ; + +default : +dev_err (dwmac->dev,"unsupported interface %d\n" , + plat_dat->interface); +return -EINVAL ; + } + + regmap =syscon_regmap_lookup_by_phandle_args (dwmac->dev->of_node, +"starfive,syscon" , +2 , args); +if (IS_ERR (regmap)) +return dev_err_probe (dwmac->dev,PTR_ERR (regmap),"getting the regmap failed\n" ); + +/* args[0]:offset args[1]: shift */ + err =regmap_update_bits (regmap, args[0 ], +STARFIVE_DWMAC_PHY_INFT_FIELD << args[1 ], + mode << args[1 ]); +if (err) +return dev_err_probe (dwmac->dev, err,"error setting phy mode\n" ); + +return 0 ; +} +static int starfive_dwmac_probe (struct platform_device *pdev) {struct plat_stmmacenet_data *plat_dat;
@@ -91,6 +135,10 @@ static int starfive_dwmac_probe(struct platform_device *pdev) plat_dat->bsp_priv = dwmac; plat_dat->dma_cfg->dche = true; + err =starfive_dwmac_set_mode (plat_dat); +if (err) +return err; + err =stmmac_dvr_probe (&pdev->dev, plat_dat, &stmmac_res);if (err) {stmmac_remove_config_dt (pdev, plat_dat);
Signature · 7 lines
2.17.1 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
This series was applied to netdev/net-next.git (main) by Paolo Abeni <[email protected]>:
Hello:
This series was applied to netdev/net-next.git (main) by Paolo Abeni <[email protected]>:
Quoted 10 lines · On Mon, 17 Apr 2023 18:02:45 +0800 you wrote:
This series adds ethernet support for the StarFive JH7110 RISC-V SoC, which includes a dwmac-5.20 MAC driver (from Synopsys DesignWare). This series has been tested and works fine on VisionFive-2 v1.2A and v1.3B SBC boards.
For more information and support, you can visit RVspace wiki[1]. You can simply review or test the patches at the link [2]. This patchset should be applied after the patchset [3] [4].
[...]
Here is the summary with links:
- [-net-next,v12,1/6] dt-bindings: net: snps,dwmac: Add dwmac-5.20 version
https://git.kernel.org/netdev/net-next/c/13f9351180aa - [-net-next,v12,2/6] net: stmmac: platform: Add snps,dwmac-5.20 IP compatible string https://git.kernel.org/netdev/net-next/c/65a1d72f0c7c - [-net-next,v12,3/6] dt-bindings: net: snps,dwmac: Add 'ahb' reset/reset-name https://git.kernel.org/netdev/net-next/c/843f603762a5 - [-net-next,v12,4/6] dt-bindings: net: Add support StarFive dwmac https://git.kernel.org/netdev/net-next/c/b76eaf7d7ede - [-net-next,v12,5/6] net: stmmac: Add glue layer for StarFive JH7110 SoC https://git.kernel.org/netdev/net-next/c/4bd3bb7b4526 - [-net-next,v12,6/6] net: stmmac: dwmac-starfive: Add phy interface settings https://git.kernel.org/netdev/net-next/c/b4a5afa51cee
You are awesome, thank you!
Signature · 2 lines
Deet-doot-dot, I am a bot. https://korg.docs.kernel.org/patchwork/pwbot.html
Re: [-net-next v12 0/6] Add Ethernet driver for StarFive JH7110 SoC
From: [email protected]
to: Samin Guo <[email protected]>
data: 2023/4/18
Quoted 31 lines
Hello:
This series was applied to netdev/net-next.git (main) by Paolo Abeni <[email protected]>:
Quoted 10 lines · On Mon, 17 Apr 2023 18:02:45 +0800 you wrote:
This series adds ethernet support for the StarFive JH7110 RISC-V SoC, which includes a dwmac-5.20 MAC driver (from Synopsys DesignWare). This series has been tested and works fine on VisionFive-2 v1.2A and v1.3B SBC boards.
For more information and support, you can visit RVspace wiki[1]. You can simply review or test the patches at the link [2]. This patchset should be applied after the patchset [3] [4].
[...]
Here is the summary with links:
- [-net-next,v12,1/6] dt-bindings: net: snps,dwmac: Add dwmac-5.20 versionhttps://git.kernel.org/netdev/net-next/c/13f9351180aa - [-net-next,v12,2/6] net: stmmac: platform: Add snps,dwmac-5.20 IP compatible string https://git.kernel.org/netdev/net-next/c/65a1d72f0c7c - [-net-next,v12,3/6] dt-bindings: net: snps,dwmac: Add 'ahb' reset/reset-name https://git.kernel.org/netdev/net-next/c/843f603762a5 - [-net-next,v12,4/6] dt-bindings: net: Add support StarFive dwmac https://git.kernel.org/netdev/net-next/c/b76eaf7d7ede - [-net-next,v12,5/6] net: stmmac: Add glue layer for StarFive JH7110 SoC https://git.kernel.org/netdev/net-next/c/4bd3bb7b4526 - [-net-next,v12,6/6] net: stmmac: dwmac-starfive: Add phy interface settings https://git.kernel.org/netdev/net-next/c/b4a5afa51cee
Quoted 1 line
You are awesome, thank you!
Thank you so much! Looking forward to seeing it in v6.4.
Best regards,
Samin