arm64: dts: rk3399-pinephone-pro: Add support for volume keys
Subsystems (2)
PATCH 1/1 arm64: dts: rk3399-pinephone-pro: Add support for volume keys
From: Ondrej Jirman <[email protected]>
These are implemented via regular ADC, so regular polling is needed, for these keys to work.
--- .../dts/rockchip/rk3399-pinephone-pro.dts | 26 +++++++++++++++++++ 1 file changed, 26 insertions(+)
arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts +26 -0
@@ -10,6 +10,7 @@ */ /dts-v1/; +#include <dt-bindings/input/gpio-keys.h> #include <dt-bindings/input/linux-event-codes.h> #include "rk3399.dtsi" #include "rk3399-opp.dtsi"
@@ -29,6 +30,26 @@ chosen { stdout-path = "serial2:115200n8"; }; + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 1>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1600000>; + poll-interval = <100>; + + button-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + press-threshold-microvolt = <100000>; + }; + + button-down { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + press-threshold-microvolt = <300000>; + }; + }; + gpio-keys { compatible = "gpio-keys"; pinctrl-names = "default";
@@ -429,6 +450,11 @@ &sdio0 { status = "okay"; }; +&saradc { + vref-supply = <&vcca1v8_s3>; + status = "okay"; +}; + &sdmmc { bus-width = <4>; cap-sd-highspeed;
Signature · 1 line
2.40.0
Hello Peter,
Quoted 36 lines · Peter Robinson
From: Ondrej Jirman <[email protected]>
These are implemented via regular ADC, so regular polling is needed, for these keys to work.
Signed-off-by Martijn Braam <[email protected]>Co-developed-by Kamil Trzciński <[email protected]>Signed-off-by Ondrej Jirman <[email protected]>Signed-off-by Peter Robinson <[email protected]>--- .../dts/rockchip/rk3399-pinephone-pro.dts | 26 +++++++++++++++++++ 1 file changed, 26 insertions(+)arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts +8
-0@@ -10,6 +10,7 @@ */ /dts-v1/; +#include <dt-bindings/input/gpio-keys.h> #include <dt-bindings/input/linux-event-codes.h> #include "rk3399.dtsi" #include "rk3399-opp.dtsi"@@ -29,6 +30,26 @@ chosen { stdout-path = "serial2:115200n8"; }; + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 1>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1600000>; + poll-interval = <100>; +
arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts chosen { · line 49
Quoted 10 lines
arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts +10
-0+ button-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + press-threshold-microvolt = <100000>; + }; + + button-down { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + press-threshold-microvolt = <300000>;
I don't know about this... I've tried reading voltage values from:
cd /sys/bus/iio/devices/iio:device0 (path may differ on your kernel)
echo $((`cat in_voltage_scale`*`cat in_voltage1_raw`))
and I get various readings around the value 300 mV on both sides of the threshold when pressing the vol down key. So this threshold may not be good enough in practice.
Values I get for several different pushes of the button:
293.5546875
328.7109375
332.2265625
304.1015625
297.0703125
522.0703125
(I have to press quite hard to get bellow 300 and to get reliable detection of volume down key press)
On development version of the phone, the value returned by sardac is less variable. Basically either 298.828125 or 300.5859375 but it's also on the edge.
I suggest raising the threshold to something like 600 and to do your own testing, to get more data points. Unpressed value is ~1791.2109375 on both phones, so 400 still gets a lot of headroom. And volume up is always < 15 in my tests.
Otherwise:
kind regards,
o.
Quoted 21 lines
arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts +8
-0+ }; + }; + gpio-keys { compatible = "gpio-keys"; pinctrl-names = "default";@@ -429,6 +450,11 @@ &sdio0 { status = "okay"; }; +&saradc { + vref-supply = <&vcca1v8_s3>; + status = "okay"; +}; + &sdmmc { bus-width = <4>; cap-sd-highspeed;Signature · 1 line
2.40.0
Heiko Stübner
maintainerHi Peter, Ondrej,
Am Mittwoch, 5. April 2023, 15:53:39 CEST schrieb Ondřej Jirman:
Quoted 70 lines · Peter Robinson
Quoted 36 lines
From: Ondrej Jirman <[email protected]>
These are implemented via regular ADC, so regular polling is needed, for these keys to work.
Signed-off-by Martijn Braam <[email protected]>Co-developed-by Kamil Trzciński <[email protected]>Signed-off-by Ondrej Jirman <[email protected]>Signed-off-by Peter Robinson <[email protected]>--- .../dts/rockchip/rk3399-pinephone-pro.dts | 26 +++++++++++++++++++ 1 file changed, 26 insertions(+)arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts +8
-0@@ -10,6 +10,7 @@ */ /dts-v1/; +#include <dt-bindings/input/gpio-keys.h> #include <dt-bindings/input/linux-event-codes.h> #include "rk3399.dtsi" #include "rk3399-opp.dtsi"@@ -29,6 +30,26 @@ chosen { stdout-path = "serial2:115200n8"; }; + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 1>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1600000>; + poll-interval = <100>; +arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts chosen { · line 49
Quoted 10 lines
arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts +10
-0+ button-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + press-threshold-microvolt = <100000>; + }; + + button-down { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + press-threshold-microvolt = <300000>;I don't know about this... I've tried reading voltage values from:
cd /sys/bus/iio/devices/iio:device0 (path may differ on your kernel)
echo $((`cat in_voltage_scale`*`cat in_voltage1_raw`))and I get various readings around the value 300 mV on both sides of the threshold when pressing the vol down key. So this threshold may not be good enough in practice.
Values I get for several different pushes of the button:
293.5546875
328.7109375
332.2265625
304.1015625
297.0703125
522.0703125(I have to press quite hard to get bellow 300 and to get reliable detection of volume down key press)
Quoted 8 lines
On development version of the phone, the value returned by sardac is less variable. Basically either 298.828125 or 300.5859375 but it's also on the edge.
I suggest raising the threshold to something like 600 and to do your own testing, to get more data points. Unpressed value is ~1791.2109375 on both phones, so 400 still gets a lot of headroom. And volume up is always < 15 in my tests.
did this get more attention meanwhile?
I don't have a Pinephone Pro myself, so you'll need to decide between you about the value and the concern Ondrej raised here for the value.
Thanks
Heiko
Quoted 26 lines
Otherwise:
Tested-by Ondrej Jirman <[email protected]>kind regards,
o.Quoted 18 lines
arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts +8
-0+ }; + }; + gpio-keys { compatible = "gpio-keys"; pinctrl-names = "default";@@ -429,6 +450,11 @@ &sdio0 { status = "okay"; }; +&saradc { + vref-supply = <&vcca1v8_s3>; + status = "okay"; +}; + &sdmmc { bus-width = <4>; cap-sd-highspeed;
Hello Heiko,
Quoted 17 lines · Heiko Stübner
Hi Peter, Ondrej,
Am Mittwoch, 5. April 2023, 15:53:39 CEST schrieb Ondřej Jirman:
Quoted 5 lines
[...]
(I have to press quite hard to get bellow 300 and to get reliable detection of volume down key press)
Quoted 8 lines
On development version of the phone, the value returned by sardac is less variable. Basically either 298.828125 or 300.5859375 but it's also on the edge.
I suggest raising the threshold to something like 600 and to do your own testing, to get more data points. Unpressed value is ~1791.2109375 on both phones, so 400 still gets a lot of headroom. And volume up is always < 15 in my tests.
Quoted 4 lines
did this get more attention meanwhile?
I don't have a Pinephone Pro myself, so you'll need to decide between you about the value and the concern Ondrej raised here for the value.
It's safe and needed to use a higher value.
SAR ADC input is pulled high to 1.8V unless some key is pressed, so unpressed value will always be around 1800 on all Pinephones, and pressed value will depend on contact quality and tolerances. For volume down, SAR ADC input is fed from a resistor divider of (10kOhm + 2kOhm) from 1.8V power rail. So that gives 2/12*1.8 = 0.3V. We can't have the press detection threshold right at this voltage, because:
1) these resistors have tolerances that will randomly result in measured voltage being above or below the 0.3V on real devices (-1% on 10k and +1% on 2k = 2*1.01/(10*0.99+2*1.01)*1.8 = 305 mV - already too high even without considering switch contact quality), and
2) those piddly membrane switches apparently have their own random resistance that is added to the bottom leg of the resistor divider, and depends on strenght of the press on some devices (and switches may develop higher resistance with age/use).
Schematic: https://megous.com/dl/tmp/1125d9248a8213b3.png
kind regards,
o.
Quoted 2 lines
Thanks
Heiko
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Heiko Stübner
maintainerAm Montag, 17. April 2023, 14:37:16 CEST schrieb Ondřej Jirman:
Quoted 20 lines
Hello Heiko,
Quoted 17 lines · Heiko Stübner
Hi Peter, Ondrej,
Am Mittwoch, 5. April 2023, 15:53:39 CEST schrieb Ondřej Jirman:
Quoted 13 lines
[...]
(I have to press quite hard to get bellow 300 and to get reliable detection of volume down key press)
On development version of the phone, the value returned by sardac is less variable. Basically either 298.828125 or 300.5859375 but it's also on the edge.
I suggest raising the threshold to something like 600 and to do your own testing, to get more data points. Unpressed value is ~1791.2109375 on both phones, so 400 still gets a lot of headroom. And volume up is always < 15 in my tests.
Quoted 6 lines
Quoted 4 lines
did this get more attention meanwhile?
I don't have a Pinephone Pro myself, so you'll need to decide between you about the value and the concern Ondrej raised here for the value.
It's safe and needed to use a higher value.
so in a nutshell, if I change "Volume Down" to say 400000 instead of the current 300000, the patch is good to go?
I.e. that was my main question :-), as you raised the objection to the value in your initial reply
Thanks
Heiko
Quoted 25 lines
SAR ADC input is pulled high to 1.8V unless some key is pressed, so unpressed value will always be around 1800 on all Pinephones, and pressed value will depend on contact quality and tolerances. For volume down, SAR ADC input is fed from a resistor divider of (10kOhm + 2kOhm) from 1.8V power rail. So that gives 2/12*1.8 = 0.3V. We can't have the press detection threshold right at this voltage, because:
1) these resistors have tolerances that will randomly result in measured voltage being above or below the 0.3V on real devices (-1% on 10k and +1% on 2k = 2*1.01/(10*0.99+2*1.01)*1.8 = 305 mV - already too high even without considering switch contact quality), and
2) those piddly membrane switches apparently have their own random resistance that is added to the bottom leg of the resistor divider, and depends on strenght of the press on some devices (and switches may develop higher resistance with age/use).
Schematic: https://megous.com/dl/tmp/1125d9248a8213b3.png
kind regards,
o.Quoted 2 lines
Thanks
Heiko
Quoted 23 lines · Heiko Stübner
Am Montag, 17. April 2023, 14:37:16 CEST schrieb Ondřej Jirman:
Quoted 22 lines
Hello Heiko,
Quoted 19 lines · Heiko Stübner
Hi Peter, Ondrej,
Am Mittwoch, 5. April 2023, 15:53:39 CEST schrieb Ondřej Jirman:
Quoted 5 lines
[...]
(I have to press quite hard to get bellow 300 and to get reliable detection of volume down key press)
Quoted 8 lines
On development version of the phone, the value returned by sardac is less variable. Basically either 298.828125 or 300.5859375 but it's also on the edge.
I suggest raising the threshold to something like 600 and to do your own testing, to get more data points. Unpressed value is ~1791.2109375 on both phones, so 400 still gets a lot of headroom. And volume up is always < 15 in my tests.
did this get more attention meanwhile?
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
I don't have a Pinephone Pro myself, so you'll need to decide between you about the value and the concern Ondrej raised here for the value.
It's safe and needed to use a higher value.
so in a nutshell, if I change "Volume Down" to say 400000 instead of the current 300000, the patch is good to go?
My suggestion was 600 mV so 600000. :) Otherwise, yes.
kind regards,
o.
Quoted 37 lines
I.e. that was my main question :-), as you raised the objection to the value in your initial reply
Thanks
HeikoQuoted 25 lines
SAR ADC input is pulled high to 1.8V unless some key is pressed, so unpressed value will always be around 1800 on all Pinephones, and pressed value will depend on contact quality and tolerances. For volume down, SAR ADC input is fed from a resistor divider of (10kOhm + 2kOhm) from 1.8V power rail. So that gives 2/12*1.8 = 0.3V. We can't have the press detection threshold right at this voltage, because:
1) these resistors have tolerances that will randomly result in measured voltage being above or below the 0.3V on real devices (-1% on 10k and +1% on 2k = 2*1.01/(10*0.99+2*1.01)*1.8 = 305 mV - already too high even without considering switch contact quality), and
2) those piddly membrane switches apparently have their own random resistance that is added to the bottom leg of the resistor divider, and depends on strenght of the press on some devices (and switches may develop higher resistance with age/use).
Schematic: https://megous.com/dl/tmp/1125d9248a8213b3.png
kind regards,
o.Quoted 2 lines
Thanks
Heiko
Quoted 6 lines · Peter Robinson
From: Ondrej Jirman <[email protected]>
These are implemented via regular ADC, so regular polling is needed, for these keys to work.
Applied, thanks!
[1/1] arm64: dts: rk3399-pinephone-pro: Add support for volume keys
commit: d3150ed535805403291b95fd84b00b0b5ef41096
With Volume Down increased to 600mV as suggested by Ondrej
Best regards,
Signature · 1 line
Heiko Stuebner <[email protected]>
Quoted 9 lines · Heiko Stuebner
Quoted 6 lines · Peter Robinson
From: Ondrej Jirman <[email protected]>
These are implemented via regular ADC, so regular polling is needed, for these keys to work.
Quoted 6 lines
Applied, thanks!
[1/1] arm64: dts: rk3399-pinephone-pro: Add support for volume keys
commit: d3150ed535805403291b95fd84b00b0b5ef41096With Volume Down increased to 600mV as suggested by Ondrej
Thanks folks
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip