smegw01: Enable setting additional boot params
PATCH v5 1/14 smegw01: Enable setting additional boot params
From: Eduard Strehlau <[email protected]>
Introduce EXTRA_BOOTPARAMS to allow passing additional parameters to kernel command line. This is useful for debugging purposes.
---
Changes since v4:
- None
include/configs/smegw01.h | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)
include/configs/smegw01.h +7 -1
@@ -17,6 +17,11 @@/* MMC Config*/ #define CFG_SYS_FSL_ESDHC_ADDR 0 +/* default to no extra bootparams, we need an empty define for stringification*/ +#ifndef EXTRA_BOOTPARAMS +#define EXTRA_BOOTPARAMS +#endif +#define CFG_EXTRA_ENV_SETTINGS \ "image=zImage\0" \ "console=ttymxc0\0" \
@@ -26,7 +31,8 @@"mmcdev=0\0" \"mmcpart=1\0" \"mmcargs=setenv bootargs console=${console},${baudrate} " \ -"root=/dev/mmcblk0p${mmcpart} rootwait rw\0" \ +"root=/dev/mmcblk0p${mmcpart} rootwait rw " \ + __stringify(EXTRA_BOOTPARAMS) "\0" \"loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} boot/${image}\0" \"loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} boot/${fdtfile}\0" \"mmcboot=echo Booting from mmc ...; " \
Signature · 1 line
2.34.1
PATCH v5 2/14 smegw01: Select CONFIG_CMD_SQUASHFS
From: Eduard Strehlau <[email protected]>
Select CONFIG_CMD_SQUASHFS so that the SquashFS U-Boot commands are available.
---
Changes since v4:
- None
configs/smegw01_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/smegw01_defconfig +1 -0
@@ -38,6 +38,7 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y CONFIG_CMD_FAT=y +CONFIG_CMD_SQUASHFS=y CONFIG_CMD_FS_GENERIC=y CONFIG_OF_CONTROL=y CONFIG_ENV_OVERWRITE=y
Signature · 1 line
2.34.1
PATCH v5 2/14 smegw01: Select CONFIG_CMD_SQUASHFS
Quoted 5 lines
From: Eduard Strehlau <[email protected]>
SelectCONFIG_CMD_SQUASHFSso that the SquashFS U-Boot commands are available.Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 3/14 smegw01: Select bootcount support
In reply to Fabio EstevamFrom: Eduard Strehlau <[email protected]>
Add automatic boot counter that increases after every reset. After a power-on reset, it will be initialized with 1, and each reboot will increment the value by 1. By default it is disabled if bootlimit isn't set.
---
Changes since v4:
- None
configs/smegw01_defconfig | 2 ++ 1 file changed, 2 insertions(+)
configs/smegw01_defconfig +2 -0
@@ -46,6 +46,8 @@ CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_BOUNCE_BUFFER=y +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_BOOTCOUNT_ENV=y CONFIG_DFU_MMC=y CONFIG_DM_I2C=y CONFIG_SUPPORT_EMMC_BOOT=y
Signature · 1 line
2.34.1
PATCH v5 3/14 smegw01: Select bootcount support
Quoted 7 lines
From: Eduard Strehlau <[email protected]>
Add automatic boot counter that increases after every reset. After a power-on reset, it will be initialized with 1, and each reboot will increment the value by 1. By default it is disabled if bootlimit isn't set.Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 4/14 smegw01: Add altbootcmd
In reply to Fabio EstevamFrom: Eduard Strehlau <[email protected]>
Add an altbootcmd script, which is convenient way to integrate with swupdate and perform a roll back of the previous working version in the case of update failure.
---
Changes since v4:
- None
configs/smegw01_defconfig | 2 +- include/configs/smegw01.h | 8 ++++++++ 2 files changed, 9 insertions(+), 1 deletion(-)
configs/smegw01_defconfig +1 -1
@@ -18,7 +18,7 @@ CONFIG_SYS_MEMTEST_END=0xa0000000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_USE_BOOTCOMMAND=y -CONFIG_BOOTCOMMAND="if run loadimage; then run mmcboot; fi; " +CONFIG_BOOTCOMMAND="if test \"${ustate}\" = 1; then setenv upgrade_available 1; saveenv; fi; if run loadimage; then run mmcboot; fi; " CONFIG_HUSH_PARSER=y CONFIG_SYS_MAXARGS=32 CONFIG_SYS_PBSIZE=532
include/configs/smegw01.h +8 -0
@@ -33,6 +33,7 @@"mmcargs=setenv bootargs console=${console},${baudrate} " \"root=/dev/mmcblk0p${mmcpart} rootwait rw " \ __stringify(EXTRA_BOOTPARAMS) "\0" \ +"bootlimit=3\0" \"loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} boot/${image}\0" \"loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} boot/${fdtfile}\0" \"mmcboot=echo Booting from mmc ...; " \
@@ -40,6 +41,13 @@"if run loadfdt; then " \"bootz ${loadaddr} - ${fdt_addr}; " \"fi;\0" \ +"altbootcmd=echo Performing rollback...; " \ +"if test \"${mmcpart}\" = 1; then " \ +"setenv mmcpart 2; " \ +"else " \ +"setenv mmcpart 1; " \ +"fi; setenv bootcount 0; setenv upgrade_available; setenv ustate 3; saveenv; " \ +"run bootcmd;\0" /* Physical Memory Map */ #define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
Signature · 1 line
2.34.1
PATCH v5 4/14 smegw01: Add altbootcmd
Quoted 6 lines
From: Eduard Strehlau <[email protected]>
Add an altbootcmd script, which is convenient way to integrate with swupdate and perform a roll back of the previous working version in the case of update failure.Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 5/14 smegw01: Run altbootcmd in the case of failure
In reply to Fabio EstevamFrom: Eduard Strehlau <[email protected]>
Run the altbootcmd script if any step of bootcmd fails.
This ensures that always a valid image can be run.
---
Changes since v4:
- None
configs/smegw01_defconfig | 2 +- include/configs/smegw01.h | 8 +++++++- 2 files changed, 8 insertions(+), 2 deletions(-)
configs/smegw01_defconfig +1 -1
@@ -18,7 +18,7 @@ CONFIG_SYS_MEMTEST_END=0xa0000000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_USE_BOOTCOMMAND=y -CONFIG_BOOTCOMMAND="if test \"${ustate}\" = 1; then setenv upgrade_available 1; saveenv; fi; if run loadimage; then run mmcboot; fi; " +CONFIG_BOOTCOMMAND="if test \"${ustate}\" = 1; then setenv upgrade_available 1; saveenv; fi; if run loadimage; then run mmcboot; else run altbootcmd; fi; " CONFIG_HUSH_PARSER=y CONFIG_SYS_MAXARGS=32 CONFIG_SYS_PBSIZE=532
include/configs/smegw01.h +7 -1
@@ -39,7 +39,13 @@"mmcboot=echo Booting from mmc ...; " \"run mmcargs; " \"if run loadfdt; then " \ -"bootz ${loadaddr} - ${fdt_addr}; " \ +"if bootz ${loadaddr} - ${fdt_addr}; then " \ +"; " \ +"else " \ +"run altbootcmd; " \ +"fi;" \ +"else " \ +"run altbootcmd; " \"fi;\0" \"altbootcmd=echo Performing rollback...; " \"if test \"${mmcpart}\" = 1; then " \
Signature · 1 line
2.34.1
PATCH v5 5/14 smegw01: Run altbootcmd in the case of failure
Quoted 5 lines
From: Eduard Strehlau <[email protected]> Run the altbootcmd script if any step of bootcmd fails. This ensures that always a valid image can be run.
Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 6/14 smegw01: Only commit to new partition if update was successful
In reply to Fabio EstevamFrom: Eduard Strehlau <[email protected]>
When performing rootfs update via swupdate, it is convenient to check the 'ustate' variable to decide whether the update succeeded or not.
---
Changes since v4:
- None
include/configs/smegw01.h | 16 ++++++++++++---- 1 file changed, 12 insertions(+), 4 deletions(-)
include/configs/smegw01.h +12 -4
@@ -30,13 +30,19 @@"bootm_size=0x10000000\0" \"mmcdev=0\0" \"mmcpart=1\0" \ +"mmcpart_committed=1\0" \"mmcargs=setenv bootargs console=${console},${baudrate} " \ -"root=/dev/mmcblk0p${mmcpart} rootwait rw " \ +"root=/dev/mmcblk0p${mmcpart_committed} rootwait rw " \ __stringify(EXTRA_BOOTPARAMS) "\0" \ +"commit_mmc=if test \"${ustate}\" = 1 -a \"${mmcpart}\" != \"${mmcpart_committed}\"; then " \ +"setenv mmcpart_committed ${mmcpart};" \ +"saveenv;" \ +"fi;\0" \"bootlimit=3\0" \ -"loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} boot/${image}\0" \ -"loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} boot/${fdtfile}\0" \ +"loadimage=load mmc ${mmcdev}:${mmcpart_committed} ${loadaddr} boot/${image}\0" \ +"loadfdt=load mmc ${mmcdev}:${mmcpart_committed} ${fdt_addr} boot/${fdtfile}\0" \"mmcboot=echo Booting from mmc ...; " \ +"run commit_mmc; " \"run mmcargs; " \"if run loadfdt; then " \"if bootz ${loadaddr} - ${fdt_addr}; then " \
@@ -48,10 +54,12 @@"run altbootcmd; " \"fi;\0" \"altbootcmd=echo Performing rollback...; " \ -"if test \"${mmcpart}\" = 1; then " \ +"if test \"${mmcpart_committed}\" = 1; then " \"setenv mmcpart 2; " \ +"setenv mmcpart_committed 2;" \"else " \"setenv mmcpart 1; " \ +"setenv mmcpart_committed 1;" \"fi; setenv bootcount 0; setenv upgrade_available; setenv ustate 3; saveenv; " \"run bootcmd;\0"
Signature · 1 line
2.34.1
PATCH v5 6/14 smegw01: Only commit to new partition if update was successful
Quoted 5 lines
From: Eduard Strehlau <[email protected]>
When performing rootfs update via swupdate, it is convenient to check the 'ustate' variable to decide whether the update succeeded or not.Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 7/14 smegw01: Enable EMMC boot from multiple partitions
In reply to Fabio EstevamFrom: Eduard Strehlau <[email protected]>
GPT Partition labels are used for determining the right root filesystem to boot from.
The U-Boot environment is configured to reside in the eMMC hardware boot partition we are currently booted from.
This should enable a dual copy approach for upgrading the bootloader. One can overwrite the inactive hardware partition with new bootloader and environment and afterwards switch the eMMC boot partition for an atomic bootloader switch.
---
Changes since v4:
- None
board/storopack/smegw01/smegw01.c | 10 ++++++++++ configs/smegw01_defconfig | 2 ++ include/configs/smegw01.h | 12 ++++++++---- 3 files changed, 20 insertions(+), 4 deletions(-)
board/storopack/smegw01/smegw01.c +10 -0
@@ -17,6 +17,7 @@#include <asm/arch/crm_regs.h> #include <asm/setup.h> #include <asm/bootm.h> +#include <mmc.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -93,3 +94,12 @@ int board_late_init(void)return 0 ; } + +uint board_mmc_get_env_part (struct mmc *mmc) +{ +uint part =EXT_CSD_EXTRACT_BOOT_PART (mmc->part_config); + +if (part ==7 ) + part =0 ; +return part; +}
configs/smegw01_defconfig +2 -0
@@ -30,6 +30,7 @@ CONFIG_CMD_MEMTEST=y CONFIG_CMD_UNZIP=y CONFIG_CMD_DFU=y CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y CONFIG_CMD_PART=y CONFIG_CMD_DHCP=y
@@ -44,6 +45,7 @@ CONFIG_OF_CONTROL=y CONFIG_ENV_OVERWRITE=y CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_SYS_MMC_ENV_DEV=1 CONFIG_NET_RANDOM_ETHADDR=y CONFIG_BOUNCE_BUFFER=y CONFIG_BOOTCOUNT_LIMIT=y
include/configs/smegw01.h +8 -4
@@ -32,17 +32,21 @@"mmcpart=1\0" \"mmcpart_committed=1\0" \"mmcargs=setenv bootargs console=${console},${baudrate} " \ -"root=/dev/mmcblk0p${mmcpart_committed} rootwait rw " \ - __stringify(EXTRA_BOOTPARAMS) "\0" \ +"root=/dev/mmcblk${mmcdev}p${gpt_partition_entry} rootwait rw " \ + __stringify(EXTRA_BOOTPARAMS) " SM_ROOT_DEV=${mmcdev} SM_ROOT_PART=${gpt_partition_entry} SM_BOOT_PART=${boot_part}\0" \"commit_mmc=if test \"${ustate}\" = 1 -a \"${mmcpart}\" != \"${mmcpart_committed}\"; then " \"setenv mmcpart_committed ${mmcpart};" \"saveenv;" \"fi;\0" \"bootlimit=3\0" \ -"loadimage=load mmc ${mmcdev}:${mmcpart_committed} ${loadaddr} boot/${image}\0" \ -"loadfdt=load mmc ${mmcdev}:${mmcpart_committed} ${fdt_addr} boot/${fdtfile}\0" \ +"loadimage=load mmc ${mmcdev}#rootfs-${mmcpart_committed} ${loadaddr} boot/${image}\0" \ +"loadfdt=load mmc ${mmcdev}#rootfs-${mmcpart_committed} ${fdt_addr} boot/${fdtfile}\0" \ +"loadpart=gpt setenv mmc ${mmcdev} rootfs-${mmcpart_committed}\0" \ +"loadbootpart=mmc partconf 1 boot_part\0" \"mmcboot=echo Booting from mmc ...; " \"run commit_mmc; " \ +"run loadpart; " \ +"run loadbootpart; " \"run mmcargs; " \"if run loadfdt; then " \"if bootz ${loadaddr} - ${fdt_addr}; then " \
Signature · 1 line
2.34.1
PATCH v5 7/14 smegw01: Enable EMMC boot from multiple partitions
Quoted 11 lines
From: Eduard Strehlau <[email protected]>
GPT Partition labels are used for determining the right root filesystem to boot from.
The U-Boot environment is configured to reside in the eMMC hardware boot partition we are currently booted from.
This should enable a dual copy approach for upgrading the bootloader. One can overwrite the inactive hardware partition with new bootloader and environment and afterwards switch the eMMC boot partition for an atomic bootloader switch.Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 8/14 smegw01: Change default boot device to eMMC
In reply to Fabio EstevamFrom: Eduard Strehlau <[email protected]>
Let eMMC be the default boot medium.
---
Changes since v4:
- None
include/configs/smegw01.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
include/configs/smegw01.h +1 -1
@@ -28,7 +28,7 @@"fdtfile=imx7d-smegw01.dtb\0" \"fdt_addr=0x83000000\0" \"bootm_size=0x10000000\0" \ -"mmcdev=0\0" \ +"mmcdev=1\0" \"mmcpart=1\0" \"mmcpart_committed=1\0" \"mmcargs=setenv bootargs console=${console},${baudrate} " \
Signature · 1 line
2.34.1
PATCH v5 8/14 smegw01: Change default boot device to eMMC
Quoted 4 lines
From: Eduard Strehlau <[email protected]> Let eMMC be the default boot medium.
Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 9/14 smegw01: Switch to fitImage
In reply to Fabio EstevamFrom: Eduard Strehlau <[email protected]>
Instead of loading the zImage kernel and the devicetree separately, switch to the fitImage format, which is more convenient when working with secure boot, for example.
---
Changes since v4:
- None
include/configs/smegw01.h | 14 +++++--------- 1 file changed, 5 insertions(+), 9 deletions(-)
include/configs/smegw01.h +5 -9
@@ -23,7 +23,7 @@#endif #define CFG_EXTRA_ENV_SETTINGS \ - "image=zImage\0" \ + "image=fitImage\0" \ "console=ttymxc0\0" \ "fdtfile=imx7d-smegw01.dtb\0" \ "fdt_addr=0x83000000\0" \
@@ -39,8 +39,8 @@"saveenv;" \"fi;\0" \"bootlimit=3\0" \ -"loadimage=load mmc ${mmcdev}#rootfs-${mmcpart_committed} ${loadaddr} boot/${image}\0" \ -"loadfdt=load mmc ${mmcdev}#rootfs-${mmcpart_committed} ${fdt_addr} boot/${fdtfile}\0" \ +"fit_addr=0x88000000\0" \ +"loadimage=load mmc ${mmcdev}#rootfs-${mmcpart_committed} ${fit_addr} boot/${image}\0" \"loadpart=gpt setenv mmc ${mmcdev} rootfs-${mmcpart_committed}\0" \"loadbootpart=mmc partconf 1 boot_part\0" \"mmcboot=echo Booting from mmc ...; " \
@@ -48,12 +48,8 @@"run loadpart; " \"run loadbootpart; " \"run mmcargs; " \ -"if run loadfdt; then " \ -"if bootz ${loadaddr} - ${fdt_addr}; then " \ -"; " \ -"else " \ -"run altbootcmd; " \ -"fi;" \ +"if bootm ${fit_addr}; then " \ +"; " \"else " \"run altbootcmd; " \"fi;\0" \
Signature · 1 line
2.34.1
PATCH v5 9/14 smegw01: Switch to fitImage
Quoted 6 lines
From: Eduard Strehlau <[email protected]>
Instead of loading the zImage kernel and the devicetree separately, switch to the fitImage format, which is more convenient when working with secure boot, for example.Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 10/14 smegw01: Add lockdown U-Boot env support
In reply to Fabio EstevamFrom: Eduard Strehlau <[email protected]>
Add lockdown U-Boot env support so that only certain U-Boot environment variables are allowed to be modified.
---
Changes since v4:
- None
board/storopack/smegw01/Kconfig | 7 +++++ board/storopack/smegw01/smegw01.c | 17 +++++++++++ configs/smegw01_defconfig | 11 ++++++- include/configs/smegw01.h | 48 +++++++++++++++++++++++++++++-- 4 files changed, 79 insertions(+), 4 deletions(-)
board/storopack/smegw01/Kconfig +7 -0
@@ -12,4 +12,11 @@ config SYS_CONFIG_NAME config IMX_CONFIG default "board/storopack/smegw01/imximage.cfg" +config SYS_BOOT_LOCKED + bool "Lock boot process to EMMC" + default y + help + Say N here if you want to boot from eMMC and SD. + Say Y to boot from eMMC. + endif
board/storopack/smegw01/smegw01.c +17 -0
@@ -14,6 +14,7 @@#include <asm/io.h> #include <common.h> #include <env.h> +#include <env_internal.h> #include <asm/arch/crm_regs.h> #include <asm/setup.h> #include <asm/bootm.h>
@@ -103,3 +104,19 @@ uint board_mmc_get_env_part(struct mmc *mmc) part =0 ;return part; } + +enum env_location env_get_location (enum env_operation op,int prio) +{ +if (op ==ENVOP_SAVE || op ==ENVOP_ERASE ) +return ENVL_MMC ; + +switch (prio) { +case 0 : +return ENVL_NOWHERE ; + +case 1 : +return ENVL_MMC ; + } + +return ENVL_UNKNOWN ; +}
configs/smegw01_defconfig +10 -1
@@ -7,6 +7,7 @@ CONFIG_ENV_OFFSET=0x100000 CONFIG_DM_GPIO=y CONFIG_DEFAULT_DEVICE_TREE="imx7d-smegw01" CONFIG_TARGET_SMEGW01=y +# CONFIG_SYS_BOOT_LOCKED is not set CONFIG_ENV_OFFSET_REDUND=0x110000 CONFIG_ARMV7_BOOT_SEC_DEFAULT=y # CONFIG_ARMV7_VIRT is not set
@@ -17,13 +18,18 @@ CONFIG_SYS_MEMTEST_START=0x80000000 CONFIG_SYS_MEMTEST_END=0xa0000000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y +CONFIG_AUTOBOOT_MENU_SHOW=y +CONFIG_BOOTMENU_DISABLE_UBOOT_CONSOLE=y CONFIG_USE_BOOTCOMMAND=y -CONFIG_BOOTCOMMAND="if test \"${ustate}\" = 1; then setenv upgrade_available 1; saveenv; fi; if run loadimage; then run mmcboot; else run altbootcmd; fi; " +CONFIG_BOOTCOMMAND="if test \"${ustate}\" = 1; then setenv upgrade_available 1; saveenv; fi; run mmcboot; " +CONFIG_USE_PREBOOT=y +CONFIG_PREBOOT="run setup_boot_menu;" CONFIG_HUSH_PARSER=y CONFIG_SYS_MAXARGS=32 CONFIG_SYS_PBSIZE=532 # CONFIG_CMD_BOOTD is not set CONFIG_CMD_BOOTZ=y +CONFIG_CMD_BOOTMENU=y # CONFIG_CMD_IMI is not set # CONFIG_CMD_XIMG is not set CONFIG_CMD_MEMTEST=y
@@ -43,9 +49,12 @@ CONFIG_CMD_SQUASHFS=y CONFIG_CMD_FS_GENERIC=y CONFIG_OF_CONTROL=y CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_NOWHERE=y CONFIG_SYS_REDUNDAND_ENVIRONMENT=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_SYS_MMC_ENV_DEV=1 +CONFIG_ENV_WRITEABLE_LIST=y +CONFIG_ENV_ACCESS_IGNORE_FORCE=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_BOUNCE_BUFFER=y CONFIG_BOOTCOUNT_LIMIT=y
include/configs/smegw01.h +45 -3
71 lines not on this page · raw message
Signature · 1 line
2.34.1
PATCH v5 10/14 smegw01: Add lockdown U-Boot env support
Quoted 5 lines
From: Eduard Strehlau <[email protected]>
Add lockdown U-Boot env support so that only certain U-Boot environment variables are allowed to be modified.Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 11/14 smegw01: Read the second MAC address
In reply to Fabio EstevamFrom: Fabio Estevam <[email protected]>
Currently, only the first MAC address is read from the fuses.
The second MAC address is not read and Linux assigns a random one.
To prevent this behavior, read the second MAC address from the fuses and store it into the eth1addr environment variable so that it can be passed to Linux.
---
Changes since v4:
- None
board/storopack/smegw01/smegw01.c | 6 ++++++ 1 file changed, 6 insertions(+)
board/storopack/smegw01/smegw01.c +6 -0
@@ -82,6 +82,7 @@ int board_init(void)int board_late_init (void ) {struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR ; +unsigned char eth1addr[6 ];imx_iomux_v3_setup_multiple_pads (wdog_pads,ARRAY_SIZE (wdog_pads));
@@ -93,6 +94,11 @@ int board_late_init(void)*/ clrsetbits_le16 (&wdog->wcr,0 ,0x10 ); +/* Get the second MAC address */ +imx_get_mac_from_fuse (1 , eth1addr); +if (!env_get ("eth1addr" ) &&is_valid_ethaddr (eth1addr)) +eth_env_set_enetaddr ("eth1addr" , eth1addr); +return 0 ; }
Signature · 1 line
2.34.1
PATCH v5 11/14 smegw01: Read the second MAC address
Quoted 7 lines
From: Fabio Estevam <[email protected]>
Currently, only the first MAC address is read from the fuses. The second MAC address is not read and Linux assigns a random one. To prevent this behavior, read the second MAC address from the fuses and store it into the eth1addr environment variable so that it can be passed to Linux.Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 12/14 smegw01: Disable additional boot menu options
In reply to Fabio EstevamFrom: Eduard Strehlau <[email protected]>
Defaults have changed, we do not want the bootmenu to contain EFI options.
---
Changes since v4:
- None
configs/smegw01_defconfig | 2 ++ 1 file changed, 2 insertions(+)
configs/smegw01_defconfig +2 -0
@@ -19,6 +19,8 @@ CONFIG_SYS_MEMTEST_END=0xa0000000 CONFIG_FIT=y CONFIG_FIT_VERBOSE=y CONFIG_AUTOBOOT_MENU_SHOW=y +# CONFIG_BOOTSTD is not set +# CONFIG_CMD_BOOTEFI_BOOTMGR is not set CONFIG_BOOTMENU_DISABLE_UBOOT_CONSOLE=y CONFIG_USE_BOOTCOMMAND=y CONFIG_BOOTCOMMAND="if test \"${ustate}\" = 1; then setenv upgrade_available 1; saveenv; fi; run mmcboot; "
Signature · 1 line
2.34.1
PATCH v5 12/14 smegw01: Disable additional boot menu options
Quoted 5 lines
From: Eduard Strehlau <[email protected]>
Defaults have changed, we do not want the bootmenu to contain EFI options.Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 13/14 smegw01: Fix fallback to altbootcmd
In reply to Fabio EstevamFrom: Eduard Strehlau <[email protected]>
The bootcmd/altbootcmd mechanism is not invoked for bootmenus. Manually compare bootcount and bootlimit to implement fallback on all codepaths.
---
Changes since v4:
- None
configs/smegw01_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
configs/smegw01_defconfig +1 -1
@@ -23,7 +23,7 @@ CONFIG_AUTOBOOT_MENU_SHOW=y # CONFIG_CMD_BOOTEFI_BOOTMGR is not set CONFIG_BOOTMENU_DISABLE_UBOOT_CONSOLE=y CONFIG_USE_BOOTCOMMAND=y -CONFIG_BOOTCOMMAND="if test \"${ustate}\" = 1; then setenv upgrade_available 1; saveenv; fi; run mmcboot; " +CONFIG_BOOTCOMMAND="if test \"${bootcount}\" -gt \"${bootlimit}\"; then run altbootcmd; else if test \"${ustate}\" = 1; then setenv upgrade_available 1; saveenv; fi; run mmcboot; fi;" CONFIG_USE_PREBOOT=y CONFIG_PREBOOT="run setup_boot_menu;" CONFIG_HUSH_PARSER=y
Signature · 1 line
2.34.1
PATCH v5 13/14 smegw01: Fix fallback to altbootcmd
Quoted 6 lines
From: Eduard Strehlau <[email protected]>
The bootcmd/altbootcmd mechanism is not invoked for bootmenus. Manually compare bootcount and bootlimit to implement fallback on all codepaths.Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 14/14 smegw01: Convert CFG_EXTRA_ENV_SETTINGS to an env file
In reply to Fabio EstevamFrom: Fabio Estevam <[email protected]>
Currently, it is recommended to move from CFG_EXTRA_ENV_SETTINGS to an env file, so do the conversion.
---
Changes since v4:
- Also add SETUP_BOOT_MENU into the .env file (Tom).
board/storopack/smegw01/smegw01.env | 89 +++++++++++++++++++++++++++++ include/configs/smegw01.h | 68 ---------------------- 2 files changed, 89 insertions(+), 68 deletions(-) create mode 100644 board/storopack/smegw01/smegw01.env
board/storopack/smegw01/smegw01.env new file +89 -0
@@ -0,0 +1,89 @@ +// SPDX-License-Identifier: GPL-2.0+ +#ifdef CONFIG_SYS_BOOT_LOCKED +#define SETUP_BOOT_MENU setup_boot_menu=setenv bootmenu_0 eMMC=run bootcmd +#else +#define SETUP_BOOT_MENU setup_boot_menu= \ + if test "${mmcdev}" = 1; then \ + setenv emmc_priority 0; \ + setenv sd_priority 1; \ + else setenv emmc_priority 1; \ + setenv sd_priority 0; \ + fi; \ + setenv bootmenu_${emmc_priority} eMMC=run boot_emmc; \ + setenv bootmenu_${sd_priority} SD=run boot_sd; +#endif + +altbootcmd= + echo Performing rollback...; + if test "${mmcpart_committed}" = 1; then + setenv mmcpart 2; + setenv mmcpart_committed 2; + else + setenv mmcpart 1; + setenv mmcpart_committed 1; + fi; + setenv bootcount 0; + setenv upgrade_available; + setenv ustate 3; + saveenv; + run bootcmd; +boot_emmc=setenv mmcdev_wanted 1; run persist_mmcdev; run bootcmd; +boot_sd=setenv mmcdev_wanted 0; run persist_mmcdev; run bootcmd; +bootcmd=run finduuid; run distro_bootcmd +bootdelay=2 +bootlimit=3 +bootm_size=0x10000000 +commit_mmc= + if test "${ustate}" = 1 -a "${mmcpart}" != "${mmcpart_committed}"; then + setenv mmcpart_committed ${mmcpart}; + saveenv; + fi; +console=ttymxc0 +fdt_addr=0x83000000 +fdtfile=imx7d-smegw01.dtb +fit_addr=0x88000000 +image=fitImage +loadaddr=0x80800000 +loadbootpart=mmc partconf 1 boot_part +loadimage=load mmc ${mmcdev}:${gpt_partition_entry} ${fit_addr} boot/${image} +loadpart=gpt setenv mmc ${mmcdev} rootfs-${mmcpart_committed} +mmcargs= + setenv bootargs console=${console},${baudrate} root=/dev/mmcblk${mmcdev}p${gpt_partition_entry} rootwait rw SM_ROOT_DEV=${mmcdev} SM_ROOT_PART=${gpt_partition_entry} SM_BOOT_PART=${boot_part} +mmcboot= + echo Booting...; + echo mmcdev: ${mmcdev}; + run commit_mmc; + echo mmcpart: ${mmcpart_committed}; + run loadpart; + echo gptpart: ${gpt_partition_entry}; + run loadbootpart; + if run loadimage; then + ; + else + run altbootcmd; + fi; + run mmcargs; + if bootm ${fit_addr}; then + ; + else + run altbootcmd; + fi; +mmcdev=1 +mmcpart=1 +mmcpart_committed=1 +persist_mmcdev= + if test "${mmcdev}" != "${mmcdev_wanted}"; then + setenv mmcdev "${mmcdev_wanted}"; + saveenv; + fi; +setup_boot_menu= + if test "${mmcdev}" = 1; then + setenv emmc_priority 0; + setenv sd_priority 1; + else + setenv emmc_priority 1; + setenv sd_priority 0; + fi; + setenv bootmenu_${emmc_priority} eMMC=run boot_emmc; + setenv bootmenu_${sd_priority} SD=run boot_sd; +SETUP_BOOT_MENU
include/configs/smegw01.h +0 -68
82 lines not on this page · raw message
Signature · 1 line
2.34.1
Re: [PATCH v5 14/14] smegw01: Convert CFG_EXTRA_ENV_SETTINGS to an env file
Quoted 7 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Currently, it is recommended to move from
CFG_EXTRA_ENV_SETTINGSto an env file, so do the conversion.Suggested-by Tom Rini <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Signature · 1 line
Tom
PATCH v5 14/14 smegw01: Convert CFG_EXTRA_ENV_SETTINGS to an env file
In reply to Fabio EstevamQuoted 6 lines
From: Fabio Estevam <[email protected]>
Currently, it is recommended to move fromCFG_EXTRA_ENV_SETTINGSto an env file, so do the conversion.Suggested-by Tom Rini <[email protected]>Signed-off-by Fabio Estevam <[email protected]>Reviewed-by Tom Rini <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v5 1/14 smegw01: Enable setting additional boot params
In reply to Fabio EstevamQuoted 5 lines
From: Eduard Strehlau <[email protected]>
IntroduceEXTRA_BOOTPARAMSto allow passing additional parameters to kernel command line. This is useful for debugging purposes.Signed-off-by Eduard Strehlau <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Erika Unter HRB 165235 Munich, Office: Kirchenstr.5, 82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================