Skip to contentSkip to conversation

usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()

PATCH New Roger Quadros 1 participant 1 message May 3, 2023

Subsystems (3)
Stable branch USB DesignWare USB3 DRD IP driver
lore
Share & tools
lore

Roger Quadros

author
#0 lore raw

PATCH v3 1/1 usb: dwc3: gadget: Improve dwc3_gadget_suspend() and dwc3_gadget_resume()

Prevent -ETIMEDOUT error on .suspend().
e.g. If gadget driver is loaded and we are connected to a USB host, all transfers must be stopped before stopping the controller else we will not get a clean stop i.e. dwc3_gadget_run_stop() will take several seconds to complete and will return -ETIMEDOUT.

Handle error cases properly in dwc3_gadget_suspend(). Simplify dwc3_gadget_resume() by using the introduced helper function.

Fixes 9f8a67b65a49 ("usb: dwc3: gadget: fix gadget suspend/resume")
Cc [email protected]
Suggested-by Thinh Nguyen <[email protected]>
Signed-off-by Roger Quadros <[email protected]>
Acked-by Thinh Nguyen <[email protected]>

---

Changelog:

v3:
- dropped patch 1. Now no longer check for softconnect during .suspend
- in suspend error path check for softconnect and enable softconnect accordingly
- added Acked-by tag by Thinh Nguyen

v2:
- rebase on greg/usb-next
- split into 2 patches. Add Fixes tag and cc stable.
- do not check for !softconnect in error condition in dwc3_gadget_suspend()

 drivers/usb/dwc3/gadget.c | 67 ++++++++++++++++++++-------------------
 1 file changed, 34 insertions(+), 33 deletions(-)
drivers/usb/dwc3/gadget.c +34 -33
index c0ca4d12f95d..2996bcb4d53d 100644
@@ -2699,6 +2699,21 @@ static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)
 	return ret;
 }
 
+static int dwc3_gadget_soft_connect(struct dwc3 *dwc)
+{
+	/*
+	 * In the Synopsys DWC_usb31 1.90a programming guide section
+	 * 4.1.9, it specifies that for a reconnect after a
+	 * device-initiated disconnect requires a core soft reset
+	 * (DCTL.CSftRst) before enabling the run/stop bit.
+	 */
+	dwc3_core_soft_reset(dwc);
+
+	dwc3_event_buffers_setup(dwc);
+	__dwc3_gadget_start(dwc);
+	return dwc3_gadget_run_stop(dwc, true);
+}
+
 static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
 {
 	struct dwc3		*dwc = gadget_to_dwc(g);

@@ -2737,21 +2752,10 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
 
 	synchronize_irq(dwc->irq_gadget);
 
-	if (!is_on) {
+	if (!is_on)
 		ret = dwc3_gadget_soft_disconnect(dwc);
-	} else {
-		/*
-		 * In the Synopsys DWC_usb31 1.90a programming guide section
-		 * 4.1.9, it specifies that for a reconnect after a
-		 * device-initiated disconnect requires a core soft reset
-		 * (DCTL.CSftRst) before enabling the run/stop bit.
-		 */
-		dwc3_core_soft_reset(dwc);
-
-		dwc3_event_buffers_setup(dwc);
-		__dwc3_gadget_start(dwc);
-		ret = dwc3_gadget_run_stop(dwc, true);
-	}
+	else
+		ret = dwc3_gadget_soft_connect(dwc);
 
 	pm_runtime_put(dwc->dev);
 

@@ -4655,42 +4659,39 @@ void dwc3_gadget_exit(struct dwc3 *dwc)
 int dwc3_gadget_suspend(struct dwc3 *dwc)
 {
 	unsigned long flags;
+	int ret;
 
 	if (!dwc->gadget_driver)
 		return 0;
 
-	dwc3_gadget_run_stop(dwc, false);
+	ret = dwc3_gadget_soft_disconnect(dwc);
+	if (ret)
+		goto err;
 
 	spin_lock_irqsave(&dwc->lock, flags);
 	dwc3_disconnect_gadget(dwc);
-	__dwc3_gadget_stop(dwc);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
 	return 0;
+
+err:
+	/*
+	 * Attempt to reset the controller's state. Likely no
+	 * communication can be established until the host
+	 * performs a port reset.
+	 */
+	if (dwc->softconnect)
+		dwc3_gadget_soft_connect(dwc);
+
+	return ret;
 }
 
 int dwc3_gadget_resume(struct dwc3 *dwc)
 {
-	int			ret;
-
 	if (!dwc->gadget_driver || !dwc->softconnect)
 		return 0;
 
-	ret = __dwc3_gadget_start(dwc);
-	if (ret < 0)
-		goto err0;
-
-	ret = dwc3_gadget_run_stop(dwc, true);
-	if (ret < 0)
-		goto err1;
-
-	return 0;
-
-err1:
-	__dwc3_gadget_stop(dwc);
-
-err0:
-	return ret;
+	return dwc3_gadget_soft_connect(dwc);
 }
 
 void dwc3_gadget_process_pending_events(struct dwc3 *dwc)
Signature · 1 line
2.34.1