Skip to contentSkip to conversation

thermal/drivers/mediatek/lvts_thermal: Fixes to the interrupt handling

PATCH Superseded Nícolas F. R. A. Prado 2 participants 10 messages May 4, 2023 – Jun 29, 2023

Subsystems (2)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover thermal/drivers/mediatek/lvts_thermal: Fixes to the interrupt handling

Fixes in the interrupt handling of the LVTS thermal driver noticed while testing it on the Spherion Chromebook (mt8192-asurada-spherion) with the MT8192 support series [1].

These are standalone fixes and don't depend on anything else.

While version 1 fixed the interrupt storms that were happening, after doing some more testing I realized that interrupts still weren't correctly working when crossing thermal trip points, so I've added a couple more commits to get that fixed on version 2.

[1] https://lore.kernel.org/all/[email protected]/

Thanks,
Nícolas

Changes in v2:
- Added commits 3, 5, 6 to get working interrupts when crossing thermal trip points
- Updated commit 4 with interrupt flags for the offset

Nícolas F. R. A. Prado (6):
thermal/drivers/mediatek/lvts_thermal: Handle IRQ on all controllers thermal/drivers/mediatek/lvts_thermal: Honor sensors in immediate mode thermal/drivers/mediatek/lvts_thermal: Use offset threshold for IRQ thermal/drivers/mediatek/lvts_thermal: Disable undesired interrupts thermal/drivers/mediatek/lvts_thermal: Don't leave threshold zeroed thermal/drivers/mediatek/lvts_thermal: Manage threshold between
sensors

 drivers/thermal/mediatek/lvts_thermal.c | 142 ++++++++++++++++++------
 1 file changed, 110 insertions(+), 32 deletions(-)
Signature · 1 line
2.40.1
#1 lore raw

PATCH v2 1/6 thermal/drivers/mediatek/lvts_thermal: Handle IRQ on all controllers

There is a single IRQ handler for each LVTS thermal domain, and it is supposed to check each of its underlying controllers for the origin of the interrupt and clear its status. However due to a typo, only the first controller was ever being handled, which resulted in the interrupt never being cleared when it happened on the other controllers. Add the missing index so interrupts are handled for all controllers.

Fixes f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")

---

(no changes since v1)

 drivers/thermal/mediatek/lvts_thermal.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/thermal/mediatek/lvts_thermal.c +1 -1
index 3df4989f9902..2988f201633a 100644
@@ -450,7 +450,7 @@ static irqreturn_t lvts_irq_handler(int irq, void *data)
 
 	for (i = 0; i < lvts_td->num_lvts_ctrl; i++) {
 
-		aux = lvts_ctrl_irq_handler(lvts_td->lvts_ctrl);
+		aux = lvts_ctrl_irq_handler(&lvts_td->lvts_ctrl[i]);
 		if (aux != IRQ_HANDLED)
 			continue;
 
Signature · 1 line
2.40.1
#2 lore raw

PATCH v2 2/6 thermal/drivers/mediatek/lvts_thermal: Honor sensors in immediate mode

In reply to Nícolas F. R. A. Prado

Each controller can be configured to operate on immediate or filtered mode. On filtered mode, the sensors are enabled by setting the corresponding bits in MONCTL0, while on immediate mode, by setting MSRCTL1.

Previously, the code would set MSRCTL1 for all four sensors when configured to immediate mode, but given that the controller might not have all four sensors connected, this would cause interrupts to trigger for non-existent sensors. Fix this by handling the MSRCTL1 register analogously to the MONCTL0: only enable the sensors that were declared.

Fixes f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")

---

(no changes since v1)

 drivers/thermal/mediatek/lvts_thermal.c | 50 +++++++++++++------------
 1 file changed, 26 insertions(+), 24 deletions(-)
drivers/thermal/mediatek/lvts_thermal.c +26 -24
index 2988f201633a..f7d998a45ea0 100644
@@ -922,24 +922,6 @@ static int lvts_ctrl_configure(struct device *dev, struct lvts_ctrl *lvts_ctrl)
 			LVTS_HW_FILTER << 3 | LVTS_HW_FILTER;
 	writel(value, LVTS_MSRCTL0(lvts_ctrl->base));
 
-	/*
-	 * LVTS_MSRCTL1 : Measurement control
-	 *
-	 * Bits:
-	 *
-	 * 9: Ignore MSRCTL0 config and do immediate measurement on sensor3
-	 * 6: Ignore MSRCTL0 config and do immediate measurement on sensor2
-	 * 5: Ignore MSRCTL0 config and do immediate measurement on sensor1
-	 * 4: Ignore MSRCTL0 config and do immediate measurement on sensor0
-	 *
-	 * That configuration will ignore the filtering and the delays
-	 * introduced below in MONCTL1 and MONCTL2
-	 */
-	if (lvts_ctrl->mode == LVTS_MSR_IMMEDIATE_MODE) {
-		value = BIT(9) | BIT(6) | BIT(5) | BIT(4);
-		writel(value, LVTS_MSRCTL1(lvts_ctrl->base));
-	}
-
 	/*
 	 * LVTS_MONCTL1 : Period unit and group interval configuration
 	 *
@@ -1004,6 +986,8 @@ static int lvts_ctrl_start(struct device *dev, struct lvts_ctrl *lvts_ctrl)
 	struct lvts_sensor *lvts_sensors = lvts_ctrl->sensors;
 	struct thermal_zone_device *tz;
 	u32 sensor_map = 0;
+	u32 sensor_map_bits[][4] = {{BIT(4), BIT(5), BIT(6), BIT(9)},
+				    {BIT(0), BIT(1), BIT(2), BIT(3)}};
 	int i;
 
 	for (i = 0; i < lvts_ctrl->num_lvts_sensor; i++) {
@@ -1040,20 +1024,38 @@ static int lvts_ctrl_start(struct device *dev, struct lvts_ctrl *lvts_ctrl)
 		 * map, so we can enable the temperature monitoring in
 		 * the hardware thermal controller.
 		 */
-		sensor_map |= BIT(i);
+		sensor_map |= sensor_map_bits[lvts_ctrl->mode][i];
 	}
 
 	/*
-	 * Bits:
-	 *      9: Single point access flow
-	 *    0-3: Enable sensing point 0-3
-	 *
 	 * The initialization of the thermal zones give us
 	 * which sensor point to enable. If any thermal zone
 	 * was not described in the device tree, it won't be
 	 * enabled here in the sensor map.
 	 */
-	writel(sensor_map | BIT(9), LVTS_MONCTL0(lvts_ctrl->base));
+	if (lvts_ctrl->mode == LVTS_MSR_IMMEDIATE_MODE) {
+		/*
+		 * LVTS_MSRCTL1 : Measurement control
+		 *
+		 * Bits:
+		 *
+		 * 9: Ignore MSRCTL0 config and do immediate measurement on sensor3
+		 * 6: Ignore MSRCTL0 config and do immediate measurement on sensor2
+		 * 5: Ignore MSRCTL0 config and do immediate measurement on sensor1
+		 * 4: Ignore MSRCTL0 config and do immediate measurement on sensor0
+		 *
+		 * That configuration will ignore the filtering and the delays
+		 * introduced in MONCTL1 and MONCTL2
+		 */
+		writel(sensor_map, LVTS_MSRCTL1(lvts_ctrl->base));
+	} else {
+		/*
+		 * Bits:
+		 *      9: Single point access flow
+		 *    0-3: Enable sensing point 0-3
+		 */
+		writel(sensor_map | BIT(9), LVTS_MONCTL0(lvts_ctrl->base));
+	}
 
 	return 0;
 }
Signature · 1 line
2.40.1
#3 lore raw

Re: [PATCH v2 2/6] thermal/drivers/mediatek/lvts_thermal: Honor sensors in immediate mode

Quoted 52 lines · Nícolas F. R. A. Prado

Each controller can be configured to operate on immediate or filtered mode. On filtered mode, the sensors are enabled by setting the corresponding bits in MONCTL0, while on immediate mode, by setting MSRCTL1.

Previously, the code would set MSRCTL1 for all four sensors when configured to immediate mode, but given that the controller might not have all four sensors connected, this would cause interrupts to trigger for non-existent sensors. Fix this by handling the MSRCTL1 register analogously to the MONCTL0: only enable the sensors that were declared.

Fixes f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")

---

(no changes since v1)

  drivers/thermal/mediatek/lvts_thermal.c | 50 +++++++++++++------------
  1 file changed, 26 insertions(+), 24 deletions(-)
drivers/thermal/mediatek/lvts_thermal.c +0 -18
index 2988f201633a..f7d998a45ea0 100644
@@ -922,24 +922,6 @@ static int lvts_ctrl_configure(struct device *dev, struct lvts_ctrl *lvts_ctrl)
  			LVTS_HW_FILTER << 3 | LVTS_HW_FILTER;
  	writel(value, LVTS_MSRCTL0(lvts_ctrl->base));
 
-	/*
-	 * LVTS_MSRCTL1 : Measurement control
-	 *
-	 * Bits:
-	 *
-	 * 9: Ignore MSRCTL0 config and do immediate measurement on sensor3
-	 * 6: Ignore MSRCTL0 config and do immediate measurement on sensor2
-	 * 5: Ignore MSRCTL0 config and do immediate measurement on sensor1
-	 * 4: Ignore MSRCTL0 config and do immediate measurement on sensor0
-	 *
-	 * That configuration will ignore the filtering and the delays
-	 * introduced below in MONCTL1 and MONCTL2
-	 */
-	if (lvts_ctrl->mode == LVTS_MSR_IMMEDIATE_MODE) {
-		value = BIT(9) | BIT(6) | BIT(5) | BIT(4);
-		writel(value, LVTS_MSRCTL1(lvts_ctrl->base));
-	}
-
  	/*
  	 * LVTS_MONCTL1 : Period unit and group interval configuration
  	 *

drivers/thermal/mediatek/lvts_thermal.c static int lvts_ctrl_start(struct device *dev, struct lvts_ctrl *lvts_ctrl) · line 990

Quoted 5 lines
drivers/thermal/mediatek/lvts_thermal.c +2 -0
@@ -1004,6 +986,8 @@ static int lvts_ctrl_start(struct device *dev, struct lvts_ctrl *lvts_ctrl)
  	struct lvts_sensor *lvts_sensors = lvts_ctrl->sensors;
  	struct thermal_zone_device *tz;
  	u32 sensor_map = 0;
+	u32 sensor_map_bits[][4] = {{BIT(4), BIT(5), BIT(6), BIT(9)},
+				    {BIT(0), BIT(1), BIT(2), BIT(3)}};

Even correct, this initialization sounds prone to error and a bit obfuscating (eg. it assumes LVTS_MSR_IMMEDIATE_MODE is 1).

What about?

	/*
	 * A description
	 */
	u32 sensor_imm_bitmap[] = { BIT(0), BIT(1), BIT(2), BIT(3) };
	u32 sensor_filt_bitmap[] = { BIT(4), BIT(5), BIT(6), BIT(9) };

	u32 *sensor_bitmap = lvts_ctrl->mode ? LVTS_MSR_IMMEDIATE_MODE : 

sensor_imm_bitmap : sensor_filt_bitmap;

drivers/thermal/mediatek/lvts_thermal.c static int lvts_ctrl_start(struct device *dev, struct lvts_ctrl *lvts_ctrl) · line 1027

Quoted 9 lines
drivers/thermal/mediatek/lvts_thermal.c +1 -1
  	int i;
 
  	for (i = 0; i < lvts_ctrl->num_lvts_sensor; i++) {
@@ -1040,20 +1024,38 @@ static int lvts_ctrl_start(struct device *dev, struct lvts_ctrl *lvts_ctrl)
  		 * map, so we can enable the temperature monitoring in
  		 * the hardware thermal controller.
  		 */
-		sensor_map |= BIT(i);
+		sensor_map |= sensor_map_bits[lvts_ctrl->mode][i];
		sensor_map |= sensor_bitmap[i];
Quoted 39 lines
drivers/thermal/mediatek/lvts_thermal.c +23 -5
  	}
 
  	/*
-	 * Bits:
-	 *      9: Single point access flow
-	 *    0-3: Enable sensing point 0-3
-	 *
  	 * The initialization of the thermal zones give us
  	 * which sensor point to enable. If any thermal zone
  	 * was not described in the device tree, it won't be
  	 * enabled here in the sensor map.
  	 */
-	writel(sensor_map | BIT(9), LVTS_MONCTL0(lvts_ctrl->base));
+	if (lvts_ctrl->mode == LVTS_MSR_IMMEDIATE_MODE) {
+		/*
+		 * LVTS_MSRCTL1 : Measurement control
+		 *
+		 * Bits:
+		 *
+		 * 9: Ignore MSRCTL0 config and do immediate measurement on sensor3
+		 * 6: Ignore MSRCTL0 config and do immediate measurement on sensor2
+		 * 5: Ignore MSRCTL0 config and do immediate measurement on sensor1
+		 * 4: Ignore MSRCTL0 config and do immediate measurement on sensor0
+		 *
+		 * That configuration will ignore the filtering and the delays
+		 * introduced in MONCTL1 and MONCTL2
+		 */
+		writel(sensor_map, LVTS_MSRCTL1(lvts_ctrl->base));
+	} else {
+		/*
+		 * Bits:
+		 *      9: Single point access flow
+		 *    0-3: Enable sensing point 0-3
+		 */
+		writel(sensor_map | BIT(9), LVTS_MONCTL0(lvts_ctrl->base));
+	}
 
  	return 0;
  }
Signature · 5 lines
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#4 lore raw

PATCH v2 3/6 thermal/drivers/mediatek/lvts_thermal: Use offset threshold for IRQ

In reply to Nícolas F. R. A. Prado

There are two kinds of temperature monitoring interrupts available:
* High Offset, Low Offset
* Hot, Hot to normal, Cold

The code currently uses the hot/h2n/cold interrupts, however in a way that doesn't work: the cold threshold is left uninitialized, which prevents the other thresholds from ever triggering, and the h2n interrupt is used as the lower threshold, which prevents the hot interrupt from triggering again after the thresholds are updated by the thermal framework, since a hot interrupt can only trigger again after the hot to normal interrupt has been triggered.

But better yet than addressing those issues, is to use the high/low offset interrupts instead. This way only two thresholds need to be managed, which have a simpler state machine, making them a better match to the thermal framework's high and low thresholds.

Fixes f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")

---

Changes in v2:
- Added this commit

 drivers/thermal/mediatek/lvts_thermal.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/thermal/mediatek/lvts_thermal.c +6 -6
index f7d998a45ea0..8449ba6ca90e 100644
@@ -297,9 +297,9 @@ static int lvts_set_trips(struct thermal_zone_device *tz, int low, int high)
 	u32 raw_high = lvts_temp_to_raw(high);
 
 	/*
-	 * Hot to normal temperature threshold
+	 * Low offset temperature threshold
 	 *
-	 * LVTS_H2NTHRE
+	 * LVTS_OFFSETL
 	 *
 	 * Bits:
 	 *
@@ -308,13 +308,13 @@ static int lvts_set_trips(struct thermal_zone_device *tz, int low, int high)
 	if (low != -INT_MAX) {
 		pr_debug("%s: Setting low limit temperature interrupt: %d\n",
 			 thermal_zone_device_type(tz), low);
-		writel(raw_low, LVTS_H2NTHRE(base));
+		writel(raw_low, LVTS_OFFSETL(base));
 	}
 
 	/*
-	 * Hot temperature threshold
+	 * High offset temperature threshold
 	 *
-	 * LVTS_HTHRE
+	 * LVTS_OFFSETH
 	 *
 	 * Bits:
 	 *
@@ -322,7 +322,7 @@ static int lvts_set_trips(struct thermal_zone_device *tz, int low, int high)
 	 */
 	pr_debug("%s: Setting high limit temperature interrupt: %d\n",
 		 thermal_zone_device_type(tz), high);
-	writel(raw_high, LVTS_HTHRE(base));
+	writel(raw_high, LVTS_OFFSETH(base));
 
 	return 0;
 }
Signature · 1 line
2.40.1
#5 lore raw

PATCH v2 4/6 thermal/drivers/mediatek/lvts_thermal: Disable undesired interrupts

In reply to Nícolas F. R. A. Prado

Out of the many interrupts supported by the hardware, the only ones of interest to the driver currently are:
* The temperature went over the high offset threshold, for any of the sensors
* The temperature went below the low offset threshold, for any of the sensors
* The temperature went over the stage3 threshold

These are the only thresholds configured by the driver through the OFFSETH, OFFSETL, and PROTTC registers, respectively.

The current interrupt mask in LVTS_MONINT_CONF, enables many more interrupts, including data ready on sensors for both filtered and immediate mode. These are not only not handled by the driver, but they are also triggered too often, causing unneeded overhead. Disable these unnecessary interrupts.

The meaning of each bit can be seen in the comment describing LVTS_MONINTST in the IRQ handler.

Fixes f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")

---

Changes in v2:
- Reworded commit and changed flag to use offset interrupts instead

 drivers/thermal/mediatek/lvts_thermal.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/thermal/mediatek/lvts_thermal.c +1 -1
index 8449ba6ca90e..efd1e938e1c2 100644
@@ -63,7 +63,7 @@
 #define LVTS_HW_FILTER				0x2
 #define LVTS_TSSEL_CONF				0x13121110
 #define LVTS_CALSCALE_CONF			0x300
-#define LVTS_MONINT_CONF			0x9FBF7BDE
+#define LVTS_MONINT_CONF			0x8300318C
 
 #define LVTS_INT_SENSOR0			0x0009001F
 #define LVTS_INT_SENSOR1			0x001203E0
Signature · 1 line
2.40.1
#6 lore raw

PATCH v2 5/6 thermal/drivers/mediatek/lvts_thermal: Don't leave threshold zeroed

In reply to Nícolas F. R. A. Prado

The thermal framework might leave the low threshold unset if there aren't any lower trip points. This leaves the register zeroed, which translates to a very high temperature for the low threshold. The interrupt for this threshold is then immediately triggered, and the state machine gets stuck, preventing any other temperature monitoring interrupts to ever trigger.

(The same happens by not setting the Cold or Hot to Normal thresholds when using those)

Set the unused threshold to a valid low value. This value was chosen so that for any valid golden temperature read from the efuse, when the value is converted to raw and back again to milliCelsius, the result doesn't underflow.

Fixes f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")

---

Changes in v2:
- Added this commit

 drivers/thermal/mediatek/lvts_thermal.c | 7 +++++++
 1 file changed, 7 insertions(+)
drivers/thermal/mediatek/lvts_thermal.c +7 -0
index efd1e938e1c2..951a4cb75ef6 100644
@@ -82,6 +82,8 @@
 #define LVTS_HW_SHUTDOWN_MT8195		105000
 #define LVTS_HW_SHUTDOWN_MT8192		105000
 
+#define LVTS_MINIUM_THRESHOLD		20000
+
 static int golden_temp = LVTS_GOLDEN_TEMP_DEFAULT;
 static int coeff_b = LVTS_COEFF_B;
 
@@ -309,6 +311,11 @@ static int lvts_set_trips(struct thermal_zone_device *tz, int low, int high)
 		pr_debug("%s: Setting low limit temperature interrupt: %d\n",
 			 thermal_zone_device_type(tz), low);
 		writel(raw_low, LVTS_OFFSETL(base));
+	} else {
+		pr_debug("%s: Setting low limit temperature to minimum\n",
+			 thermal_zone_device_type(tz));
+		raw_low = lvts_temp_to_raw(LVTS_MINIUM_THRESHOLD);
+		writel(raw_low, LVTS_OFFSETL(base));
 	}
 
 	/*
Signature · 1 line
2.40.1
#7 lore raw

Re: [PATCH v2 5/6] thermal/drivers/mediatek/lvts_thermal: Don't leave threshold zeroed

Quoted 31 lines · Nícolas F. R. A. Prado

The thermal framework might leave the low threshold unset if there aren't any lower trip points. This leaves the register zeroed, which translates to a very high temperature for the low threshold. The interrupt for this threshold is then immediately triggered, and the state machine gets stuck, preventing any other temperature monitoring interrupts to ever trigger.

(The same happens by not setting the Cold or Hot to Normal thresholds when using those)

Set the unused threshold to a valid low value. This value was chosen so that for any valid golden temperature read from the efuse, when the value is converted to raw and back again to milliCelsius, the result doesn't underflow.

Fixes f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")

---

Changes in v2:
- Added this commit

  drivers/thermal/mediatek/lvts_thermal.c | 7 +++++++
  1 file changed, 7 insertions(+)
drivers/thermal/mediatek/lvts_thermal.c +0 -0
index efd1e938e1c2..951a4cb75ef6 100644

drivers/thermal/mediatek/lvts_thermal.c line 85

Quoted 4 lines
drivers/thermal/mediatek/lvts_thermal.c +1 -0
@@ -82,6 +82,8 @@
  #define LVTS_HW_SHUTDOWN_MT8195		105000
  #define LVTS_HW_SHUTDOWN_MT8192		105000
 
+#define LVTS_MINIUM_THRESHOLD		20000

MINIMUM

So if the thermal zone reaches 20°C, the interrupt fires, the set_trips sets again 20°C but the interrupt won't fire until the temperature goes above 20°C and then crosses the temperature low threshold the way down again?

drivers/thermal/mediatek/lvts_thermal.c static int lvts_set_trips(struct thermal_zone_device *tz, int low, int high) · line 318

Quoted 12 lines
drivers/thermal/mediatek/lvts_thermal.c +5 -0
  static int golden_temp = LVTS_GOLDEN_TEMP_DEFAULT;
  static int coeff_b = LVTS_COEFF_B;
 
@@ -309,6 +311,11 @@ static int lvts_set_trips(struct thermal_zone_device *tz, int low, int high)
  		pr_debug("%s: Setting low limit temperature interrupt: %d\n",
  			 thermal_zone_device_type(tz), low);
  		writel(raw_low, LVTS_OFFSETL(base));
+	} else {
+		pr_debug("%s: Setting low limit temperature to minimum\n",
+			 thermal_zone_device_type(tz));
+		raw_low = lvts_temp_to_raw(LVTS_MINIUM_THRESHOLD);
+		writel(raw_low, LVTS_OFFSETL(base));

That's duplicate code:

u32 raw_low = lvts_temp_to_raw(low != -INT_MAX ? low : LVTS_MINIMUM_THRESHOLD);

And then the condition in the code goes away:

        if (low != -INT_MAX) {
	}
Quoted 3 lines
drivers/thermal/mediatek/lvts_thermal.c +0 -0
  	}
 
  	/*
Signature · 5 lines
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#8 lore raw

Re: [PATCH v2 5/6] thermal/drivers/mediatek/lvts_thermal: Don't leave threshold zeroed

Quoted 38 lines · Daniel Lezcano
Quoted 31 lines · Nícolas F. R. A. Prado

The thermal framework might leave the low threshold unset if there aren't any lower trip points. This leaves the register zeroed, which translates to a very high temperature for the low threshold. The interrupt for this threshold is then immediately triggered, and the state machine gets stuck, preventing any other temperature monitoring interrupts to ever trigger.

(The same happens by not setting the Cold or Hot to Normal thresholds when using those)

Set the unused threshold to a valid low value. This value was chosen so that for any valid golden temperature read from the efuse, when the value is converted to raw and back again to milliCelsius, the result doesn't underflow.

Fixes f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")

---

Changes in v2:
- Added this commit

  drivers/thermal/mediatek/lvts_thermal.c | 7 +++++++
  1 file changed, 7 insertions(+)
drivers/thermal/mediatek/lvts_thermal.c +0 -0
index efd1e938e1c2..951a4cb75ef6 100644

drivers/thermal/mediatek/lvts_thermal.c line 84

Quoted 3 lines
drivers/thermal/mediatek/lvts_thermal.c +1 -0
@@ -82,6 +82,8 @@
  #define LVTS_HW_SHUTDOWN_MT8195		105000
  #define LVTS_HW_SHUTDOWN_MT8192		105000
+#define LVTS_MINIUM_THRESHOLD		20000

MINIMUM

Quoted 3 lines

So if the thermal zone reaches 20°C, the interrupt fires, the set_trips sets again 20°C but the interrupt won't fire until the temperature goes above 20°C and then crosses the temperature low threshold the way down again?

Well, actually, set_trips won't even be called since from the thermal framework's perspective we haven't crossed trip points, ie in __thermal_zone_set_trips():

	/* No need to change trip points */
	if (tz->prev_low_trip == low && tz->prev_high_trip == high)
		return;

But in any case, yes, the interrupt will fire, the temperature will get updated in the framework, and that's it. It will only fire again when a threshold is crossed again (either by the temperature rising and falling again below this minimum, or rising beyond the high treshold).

So basically at most this will cause a spurious interrupt when the temperature gets low enough. I do get 34-36C on all sensors when idling though, so I doubt that temperature is even reachable. Besides, we don't really have another option here if we want working interrupts, the threshold needs to be set to a valid value, and this is the lowest I've found.

And thanks for all the feedback! I'll prepare a v3 based on your comments.

Thanks,
Nícolas

#9 lore raw

PATCH v2 6/6 thermal/drivers/mediatek/lvts_thermal: Manage threshold between sensors

In reply to Nícolas F. R. A. Prado

Each LVTS thermal controller can have up to four sensors, each capable of triggering its own interrupt when its measured temperature crosses the configured threshold. The threshold for each sensor is handled separately by the thermal framework, since each one is registered with its own thermal zone and trips. However, the temperature thresholds are configured on the controller, and therefore are shared between all sensors on that controller.

When the temperature measured by the sensors is different enough to cause the thermal framework to configure different thresholds for each one, interrupts start triggering on sensors outside the last threshold configured.

To address the issue, track the thresholds required by each sensor and only actually set the highest one in the hardware, and disable interrupts for all sensors outside the current configured range.

Fixes f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")

---

Changes in v2:
- Added this commit

 drivers/thermal/mediatek/lvts_thermal.c | 69 +++++++++++++++++++++++++
 1 file changed, 69 insertions(+)
drivers/thermal/mediatek/lvts_thermal.c +69 -0
index 951a4cb75ef6..2f37a175b1c6 100644
@@ -65,6 +65,11 @@
 #define LVTS_CALSCALE_CONF			0x300
 #define LVTS_MONINT_CONF			0x8300318C
 
+#define LVTS_MONINT_OFFSET_SENSOR0		0xC
+#define LVTS_MONINT_OFFSET_SENSOR1		0x180
+#define LVTS_MONINT_OFFSET_SENSOR2		0x3000
+#define LVTS_MONINT_OFFSET_SENSOR3		0x3000000
+
 #define LVTS_INT_SENSOR0			0x0009001F
 #define LVTS_INT_SENSOR1			0x001203E0
 #define LVTS_INT_SENSOR2			0x00247C00
@@ -111,6 +116,8 @@ struct lvts_sensor {
 	void __iomem *base;
 	int id;
 	int dt_id;
+	int low_thresh;
+	int high_thresh;
 };
 
 struct lvts_ctrl {
@@ -120,6 +127,8 @@ struct lvts_ctrl {
 	int num_lvts_sensor;
 	int mode;
 	void __iomem *base;
+	int low_thresh;
+	int high_thresh;
 };
 
 struct lvts_domain {
@@ -291,12 +300,66 @@ static int lvts_get_temp(struct thermal_zone_device *tz, int *temp)
 	return 0;
 }
 
+static void lvts_update_irq_mask(struct lvts_ctrl *lvts_ctrl)
+{
+	u32 masks[] = {
+		LVTS_MONINT_OFFSET_SENSOR0,
+		LVTS_MONINT_OFFSET_SENSOR1,
+		LVTS_MONINT_OFFSET_SENSOR2,
+		LVTS_MONINT_OFFSET_SENSOR3,
+	};
+	u32 value = 0;
+	int i;
+
+	value = readl(LVTS_MONINT(lvts_ctrl->base));
+
+	for (i = 0; i < ARRAY_SIZE(masks); i++) {
+		if (lvts_ctrl->sensors[i].high_thresh == lvts_ctrl->high_thresh
+		    && lvts_ctrl->sensors[i].low_thresh == lvts_ctrl->low_thresh)
+			value |= masks[i];
+		else
+			value &= ~masks[i];
+	}
+
+	writel(value, LVTS_MONINT(lvts_ctrl->base));
+}
+
+static bool lvts_should_update_thresh(struct lvts_ctrl *lvts_ctrl, int high)
+{
+	int i;
+
+	if (high > lvts_ctrl->high_thresh)
+		return true;
+
+	for (i = 0; i < lvts_ctrl->num_lvts_sensor; i++)
+		if (lvts_ctrl->sensors[i].high_thresh == lvts_ctrl->high_thresh
+		    && lvts_ctrl->sensors[i].low_thresh == lvts_ctrl->low_thresh)
+			return false;
+
+	return true;
+}
+
 static int lvts_set_trips(struct thermal_zone_device *tz, int low, int high)
 {
 	struct lvts_sensor *lvts_sensor = thermal_zone_device_priv(tz);
+	struct lvts_ctrl *lvts_ctrl = container_of(lvts_sensor, struct lvts_ctrl, sensors[lvts_sensor->id]);
 	void __iomem *base = lvts_sensor->base;
 	u32 raw_low = lvts_temp_to_raw(low);
 	u32 raw_high = lvts_temp_to_raw(high);
+	bool should_update_thresh;
+
+	lvts_sensor->low_thresh = low;
+	lvts_sensor->high_thresh = high;
+
+	should_update_thresh = lvts_should_update_thresh(lvts_ctrl, high);
+	if (should_update_thresh) {
+		lvts_ctrl->high_thresh = high;
+		lvts_ctrl->low_thresh = low;
+	}
+	lvts_update_irq_mask(lvts_ctrl);
+
+	if (!should_update_thresh)
+		return 0;
 
 	/*
 	 * Low offset temperature threshold
@@ -527,6 +590,9 @@ static int lvts_sensor_init(struct device *dev, struct lvts_ctrl *lvts_ctrl,
 		 */
 		lvts_sensor[i].msr = lvts_ctrl_data->mode == LVTS_MSR_IMMEDIATE_MODE ?
 			imm_regs[i] : msr_regs[i];
+
+		lvts_sensor[i].low_thresh = INT_MIN;
+		lvts_sensor[i].high_thresh = INT_MIN;
 	};
 
 	lvts_ctrl->num_lvts_sensor = lvts_ctrl_data->num_lvts_sensor;
@@ -721,6 +787,9 @@ static int lvts_ctrl_init(struct device *dev, struct lvts_domain *lvts_td,
 		 */
 		lvts_ctrl[i].hw_tshut_raw_temp =
 			lvts_temp_to_raw(lvts_data->lvts_ctrl[i].hw_tshut_temp);
+
+		lvts_ctrl[i].low_thresh = INT_MIN;
+		lvts_ctrl[i].high_thresh = INT_MIN;
 	}
 
 	/*
Signature · 1 line
2.40.1