sunxi: DT update plus new board support
Subsystems (3)
v2 cover sunxi: DT update plus new board support
Hi,
the main purpose of this series is to update the Allwinner devicetree files to the latest versions from the Linux kernel repository. Compared to the v1 post, this uses the officially released 6.4-rc2 tree instead of just linux-next, which adds the dma-names order changes that were missing the last time.
In the wake of that this adds the defconfig for a new Allwinner F1C200s board, also serving as a blueprint for other F1C200s boards.
Please have a look!
Cheers,
Andre
Andre Przywara (2):
sunxi: dts: arm/arm64: update devicetree files from Linux-v6.4-rc2
sunxi: defconfig: Add Lctech Pi F1C200s board
arch/arm/dts/axp22x.dtsi | 6 ++ arch/arm/dts/axp809.dtsi | 7 ++ arch/arm/dts/axp81x.dtsi | 14 ---- arch/arm/dts/sun50i-a64.dtsi | 1 + arch/arm/dts/sun50i-h5-orangepi-pc2.dts | 1 + arch/arm/dts/sun5i-gr8-chip-pro.dts | 2 +- arch/arm/dts/sun5i-r8-chip.dts | 2 +- arch/arm/dts/sun6i-a31.dtsi | 12 +-- arch/arm/dts/sun6i-a31s-sina31s.dts | 2 +- arch/arm/dts/sun8i-a23-a33.dtsi | 10 +-- arch/arm/dts/sun8i-a33.dtsi | 1 + arch/arm/dts/sun8i-a83t-bananapi-m3.dts | 15 ++++ arch/arm/dts/sun8i-h3-beelink-x2.dts | 2 +- arch/arm/dts/sun8i-h3-nanopi-duo2.dts | 2 +- arch/arm/dts/sun8i-v3s.dtsi | 6 +- arch/arm/dts/suniv-f1c100s-licheepi-nano.dts | 16 ++++ arch/arm/dts/suniv-f1c100s.dtsi | 32 ++++++++ arch/arm/dts/suniv-f1c200s-lctech-pi.dts | 76 ++++++++++++++++++ arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts | 81 ++++++++++++++++++++ arch/arm/dts/sunxi-h3-h5.dtsi | 8 +- configs/lctech_pi_f1c200s_defconfig | 11 +++ 21 files changed, 270 insertions(+), 37 deletions(-) create mode 100644 arch/arm/dts/suniv-f1c200s-lctech-pi.dts create mode 100644 arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts create mode 100644 configs/lctech_pi_f1c200s_defconfig
Signature · 1 line
2.35.8
PATCH v2 1/2 sunxi: dts: arm/arm64: update devicetree files from Linux-v6.4-rc2
Sync the devicetree files from the official Linux kernel tree, v6.4-rc2. This is covering both 64-bit and 32-bit Allwinner SoCs with Arm Ltd. cores, we skip the new RISC-V bits for now, as sunxi RISC-V support is still work in progress.
Among smaller cosmetic changes, this adds a SATA regulator node which we need in U-Boot to get rid of hard-coded GPIOs.
Also this updates the Allwinner F1C100s DTs, enabling USB support, and also adds the DTs for two new boards.
As before, this omits the non-backwards compatible changes to the R_INTC controller, to remain compatible with older kernels.
--- arch/arm/dts/axp22x.dtsi | 6 ++ arch/arm/dts/axp809.dtsi | 7 ++ arch/arm/dts/axp81x.dtsi | 14 ---- arch/arm/dts/sun50i-a64.dtsi | 1 + arch/arm/dts/sun50i-h5-orangepi-pc2.dts | 1 + arch/arm/dts/sun5i-gr8-chip-pro.dts | 2 +- arch/arm/dts/sun5i-r8-chip.dts | 2 +- arch/arm/dts/sun6i-a31.dtsi | 12 +-- arch/arm/dts/sun6i-a31s-sina31s.dts | 2 +- arch/arm/dts/sun8i-a23-a33.dtsi | 10 +-- arch/arm/dts/sun8i-a33.dtsi | 1 + arch/arm/dts/sun8i-a83t-bananapi-m3.dts | 15 ++++ arch/arm/dts/sun8i-h3-beelink-x2.dts | 2 +- arch/arm/dts/sun8i-h3-nanopi-duo2.dts | 2 +- arch/arm/dts/sun8i-v3s.dtsi | 6 +- arch/arm/dts/suniv-f1c100s-licheepi-nano.dts | 16 ++++ arch/arm/dts/suniv-f1c100s.dtsi | 32 ++++++++ arch/arm/dts/suniv-f1c200s-lctech-pi.dts | 76 ++++++++++++++++++ arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts | 81 ++++++++++++++++++++ arch/arm/dts/sunxi-h3-h5.dtsi | 8 +- 20 files changed, 259 insertions(+), 37 deletions(-) create mode 100644 arch/arm/dts/suniv-f1c200s-lctech-pi.dts create mode 100644 arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts
arch/arm/dts/axp22x.dtsi +6 -0
@@ -67,6 +67,12 @@ status = "disabled"; }; + axp_gpio: gpio { + compatible = "x-powers,axp221-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + regulators { /* Default work frequency for buck regulators */ x-powers,dcdc-freq = <3000>;
arch/arm/dts/axp809.dtsi +7 -0
@@ -50,4 +50,11 @@ compatible = "x-powers,axp809"; interrupt-controller; #interrupt-cells = <1>; + + axp_gpio: gpio { + compatible = "x-powers,axp809-gpio", + "x-powers,axp221-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; };
arch/arm/dts/axp81x.dtsi +0 -14
@@ -62,16 +62,6 @@ compatible = "x-powers,axp813-gpio"; gpio-controller; #gpio-cells = <2>; - - gpio0_ldo: gpio0-ldo-pin { - pins = "GPIO0"; - function = "ldo"; - }; - - gpio1_ldo: gpio1-ldo-pin { - pins = "GPIO1"; - function = "ldo"; - }; }; battery_power_supply: battery-power {
@@ -144,15 +134,11 @@ }; reg_ldo_io0: ldo-io0 { - pinctrl-names = "default"; - pinctrl-0 = <&gpio0_ldo>; /* Disable by default to avoid conflicts with GPIO */ status = "disabled"; }; reg_ldo_io1: ldo-io1 { - pinctrl-names = "default"; - pinctrl-0 = <&gpio1_ldo>; /* Disable by default to avoid conflicts with GPIO */ status = "disabled"; };
arch/arm/dts/sun50i-a64.dtsi +1 -0
@@ -1197,6 +1197,7 @@ compatible = "allwinner,sun50i-a64-mipi-dphy", "allwinner,sun6i-a31-mipi-dphy"; reg = <0x01ca1000 0x1000>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_MIPI_DSI>, <&ccu CLK_DSI_DPHY>; clock-names = "bus", "mod";
arch/arm/dts/sun50i-h5-orangepi-pc2.dts +1 -0
@@ -3,6 +3,7 @@ /dts-v1/; #include "sun50i-h5.dtsi" +#include "sun50i-h5-cpu-opp.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h>
arch/arm/dts/sun5i-gr8-chip-pro.dts +1 -1
@@ -70,7 +70,7 @@ leds { compatible = "gpio-leds"; - status { + led-0 { label = "chip-pro:white:status"; gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>; default-state = "on";
arch/arm/dts/sun5i-r8-chip.dts +1 -1
@@ -70,7 +70,7 @@ leds { compatible = "gpio-leds"; - status { + led-0 { label = "chip:white:status"; gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>; default-state = "on";
arch/arm/dts/sun6i-a31.dtsi +6 -6
@@ -820,7 +820,7 @@ clocks = <&ccu CLK_APB2_UART0>; resets = <&ccu RST_APB2_UART0>; dmas = <&dma 6>, <&dma 6>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -833,7 +833,7 @@ clocks = <&ccu CLK_APB2_UART1>; resets = <&ccu RST_APB2_UART1>; dmas = <&dma 7>, <&dma 7>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -846,7 +846,7 @@ clocks = <&ccu CLK_APB2_UART2>; resets = <&ccu RST_APB2_UART2>; dmas = <&dma 8>, <&dma 8>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -859,7 +859,7 @@ clocks = <&ccu CLK_APB2_UART3>; resets = <&ccu RST_APB2_UART3>; dmas = <&dma 9>, <&dma 9>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -872,7 +872,7 @@ clocks = <&ccu CLK_APB2_UART4>; resets = <&ccu RST_APB2_UART4>; dmas = <&dma 10>, <&dma 10>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -885,7 +885,7 @@ clocks = <&ccu CLK_APB2_UART5>; resets = <&ccu RST_APB2_UART5>; dmas = <&dma 22>, <&dma 22>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
arch/arm/dts/sun6i-a31s-sina31s.dts +1 -1
@@ -67,7 +67,7 @@ leds { compatible = "gpio-leds"; - status { + led-0 { label = "sina31s:status:usr"; gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */ };
arch/arm/dts/sun8i-a23-a33.dtsi +5 -5
@@ -488,7 +488,7 @@ clocks = <&ccu CLK_BUS_UART0>; resets = <&ccu RST_BUS_UART0>; dmas = <&dma 6>, <&dma 6>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -501,7 +501,7 @@ clocks = <&ccu CLK_BUS_UART1>; resets = <&ccu RST_BUS_UART1>; dmas = <&dma 7>, <&dma 7>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -514,7 +514,7 @@ clocks = <&ccu CLK_BUS_UART2>; resets = <&ccu RST_BUS_UART2>; dmas = <&dma 8>, <&dma 8>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -527,7 +527,7 @@ clocks = <&ccu CLK_BUS_UART3>; resets = <&ccu RST_BUS_UART3>; dmas = <&dma 9>, <&dma 9>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -540,7 +540,7 @@ clocks = <&ccu CLK_BUS_UART4>; resets = <&ccu RST_BUS_UART4>; dmas = <&dma 10>, <&dma 10>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
arch/arm/dts/sun8i-a33.dtsi +1 -0
@@ -278,6 +278,7 @@ dphy: d-phy@1ca1000 { compatible = "allwinner,sun6i-a31-mipi-dphy"; reg = <0x01ca1000 0x1000>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_MIPI_DSI>, <&ccu CLK_DSI_DPHY>; clock-names = "bus", "mod";
arch/arm/dts/sun8i-a83t-bananapi-m3.dts +15 -0
@@ -105,6 +105,21 @@ /* enables internal regulator and de-asserts reset */ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ }; + + /* + * Power supply for the SATA disk, behind a USB-SATA bridge. + * Since it is a USB device, there is no consumer in the DT, so we + * have to keep this always on. + */ + regulator-sata-disk-pwr { + compatible = "regulator-fixed"; + regulator-name = "sata-disk-pwr"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + enable-active-high; + gpio = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */ + }; }; &cpu0 {
arch/arm/dts/sun8i-h3-beelink-x2.dts +1 -1
@@ -57,7 +57,7 @@ ethernet1 = &sdiowifi; }; - cec-gpio { + cec { compatible = "cec-gpio"; cec-gpios = <&pio 0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PA14 */ hdmi-phandle = <&hdmi>;
arch/arm/dts/sun8i-h3-nanopi-duo2.dts +1 -1
@@ -57,7 +57,7 @@ regulator-ramp-delay = <50>; /* 4ms */ enable-active-high; - enable-gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + enable-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ gpios-states = <0x1>; states = <1100000 0>, <1300000 1>;
arch/arm/dts/sun8i-v3s.dtsi +3 -3
@@ -479,7 +479,7 @@ reg-io-width = <4>; clocks = <&ccu CLK_BUS_UART0>; dmas = <&dma 6>, <&dma 6>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; resets = <&ccu RST_BUS_UART0>; status = "disabled"; };
@@ -492,7 +492,7 @@ reg-io-width = <4>; clocks = <&ccu CLK_BUS_UART1>; dmas = <&dma 7>, <&dma 7>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; resets = <&ccu RST_BUS_UART1>; status = "disabled"; };
@@ -505,7 +505,7 @@ reg-io-width = <4>; clocks = <&ccu CLK_BUS_UART2>; dmas = <&dma 8>, <&dma 8>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; resets = <&ccu RST_BUS_UART2>; pinctrl-0 = <&uart2_pins>; pinctrl-names = "default";
arch/arm/dts/suniv-f1c100s-licheepi-nano.dts +16 -0
@@ -6,6 +6,8 @@ /dts-v1/; #include "suniv-f1c100s.dtsi" +#include <dt-bindings/gpio/gpio.h> + / { model = "Lichee Pi Nano"; compatible = "licheepi,licheepi-nano", "allwinner,suniv-f1c100s";
@@ -50,8 +52,22 @@ }; }; +&otg_sram { + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pe_pins>; status = "okay"; }; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 4 2 GPIO_ACTIVE_HIGH>; /* PE2 */ + status = "okay"; +};
arch/arm/dts/suniv-f1c100s.dtsi +32 -0
@@ -133,6 +133,32 @@ #size-cells = <0>; }; + usb_otg: usb@1c13000 { + compatible = "allwinner,suniv-f1c100s-musb"; + reg = <0x01c13000 0x0400>; + clocks = <&ccu CLK_BUS_OTG>; + resets = <&ccu RST_BUS_OTG>; + interrupts = <26>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + allwinner,sram = <&otg_sram 1>; + status = "disabled"; + }; + + usbphy: phy@1c13400 { + compatible = "allwinner,suniv-f1c100s-usb-phy"; + reg = <0x01c13400 0x10>; + reg-names = "phy_ctrl"; + clocks = <&ccu CLK_USB_PHY0>; + clock-names = "usb0_phy"; + resets = <&ccu RST_USB_PHY0>; + reset-names = "usb0_reset"; + #phy-cells = <1>; + status = "disabled"; + }; + ccu: clock@1c20000 { compatible = "allwinner,suniv-f1c100s-ccu"; reg = <0x01c20000 0x400>;
@@ -181,6 +207,12 @@ pins = "PE0", "PE1"; function = "uart0"; }; + + /omit-if-no-ref/ + uart1_pa_pins: uart1-pa-pins { + pins = "PA2", "PA3"; + function = "uart1"; + }; }; i2c0: i2c@1c27000 {
arch/arm/dts/suniv-f1c200s-lctech-pi.dts new file +76 -0
76 lines not on this page · raw message
arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts new file +81 -0
81 lines not on this page · raw message
arch/arm/dts/sunxi-h3-h5.dtsi +4 -4
@@ -709,7 +709,7 @@ clocks = <&ccu CLK_BUS_UART0>; resets = <&ccu RST_BUS_UART0>; dmas = <&dma 6>, <&dma 6>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -722,7 +722,7 @@ clocks = <&ccu CLK_BUS_UART1>; resets = <&ccu RST_BUS_UART1>; dmas = <&dma 7>, <&dma 7>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -735,7 +735,7 @@ clocks = <&ccu CLK_BUS_UART2>; resets = <&ccu RST_BUS_UART2>; dmas = <&dma 8>, <&dma 8>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
@@ -748,7 +748,7 @@ clocks = <&ccu CLK_BUS_UART3>; resets = <&ccu RST_BUS_UART3>; dmas = <&dma 9>, <&dma 9>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; };
Signature · 1 line
2.35.8
PATCH v2 2/2 sunxi: defconfig: Add Lctech Pi F1C200s board
In reply to Andre PrzywaraThe Lctech Pi F1C200s (also previously known under the Cherry Pi brand) is a small development board with the Allwinner F1C200s SoC. This is the same as the F1C100s, but with 64MB instead of 32MB co-packaged DRAM.
Add a defconfig for this board, enabling the most basic features. This uses the new 64MB memory map, which avoids the very tight memory map we use for the 32MB F1C100s board(s).
The devicetree file is already in the tree, courtesy of the previous Linux repo sync.
--- configs/lctech_pi_f1c200s_defconfig | 11 +++++++++++ 1 file changed, 11 insertions(+) create mode 100644 configs/lctech_pi_f1c200s_defconfig
configs/lctech_pi_f1c200s_defconfig new file +11 -0
@@ -0,0 +1,11 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_DEFAULT_DEVICE_TREE="suniv-f1c200s-lctech-pi" +CONFIG_SPL=y +CONFIG_MACH_SUNIV=y +CONFIG_DRAM_CLK=156 +CONFIG_DRAM_ZQ=0 +CONFIG_SUNXI_MINIMUM_DRAM_MB=64 +# CONFIG_VIDEO_SUNXI is not set +CONFIG_CONS_INDEX=2 +CONFIG_SPI=y
Signature · 1 line
2.35.8