riscv: Initial support for Lichee PI 4A board
cover riscv: Initial support for Lichee PI 4A board
Sipeed's Lichee PI 4A board is based on T-HEAD's TH1520 SoC which consists of quad core XuanTie C910 CPU, plus one C906 CPU and one E902 CPU.
In this series, the UART, basic device tree, CPU, PLIC are enabled, making it capable of running in serial console mode.
Please note that, we rely on pre shipped vendor u-boot which run in M-Mode to chain load this mainline u-boot either via eMMC storage or from tftp, thus the pinctrl and clock setting are not implemented in this series, which certainly can be improved later accordingly.
Also the device tree is coming from kernel which is submitted by Jisheng Zhang in his patch V2 [1], it's still under review, so may change in the future.
[1] https://lore.kernel.org/all/[email protected]
Yixun Lan (4):
riscv: t-head: licheepi4a: initial support added
riscv: dts: t-head: Add basic device tree for Sipeed Lichee PI 4A
board
configs: th1520_lpi4a_defconfig: Add initial config
doc: t-head: lpi4a: document Lichee PI 4A board
arch/riscv/Kconfig | 5 + arch/riscv/dts/Makefile | 1 + arch/riscv/dts/th1520-lichee-module-4a.dtsi | 34 ++ arch/riscv/dts/th1520-lichee-pi-4a.dts | 32 ++ arch/riscv/dts/th1520.dtsi | 435 ++++++++++++++++++++ board/thead/th1520_lpi4a/Kconfig | 42 ++ board/thead/th1520_lpi4a/MAINTAINERS | 7 + board/thead/th1520_lpi4a/Makefile | 5 + board/thead/th1520_lpi4a/board.c | 14 + configs/th1520_lpi4a_defconfig | 82 ++++ doc/board/index.rst | 1 + doc/board/thead/index.rst | 9 + doc/board/thead/lpi4a.rst | 112 +++++ include/configs/th1520_lpi4a.h | 22 + 14 files changed, 801 insertions(+) create mode 100644 arch/riscv/dts/th1520-lichee-module-4a.dtsi create mode 100644 arch/riscv/dts/th1520-lichee-pi-4a.dts create mode 100644 arch/riscv/dts/th1520.dtsi create mode 100644 board/thead/th1520_lpi4a/Kconfig create mode 100644 board/thead/th1520_lpi4a/MAINTAINERS create mode 100644 board/thead/th1520_lpi4a/Makefile create mode 100644 board/thead/th1520_lpi4a/board.c create mode 100644 configs/th1520_lpi4a_defconfig create mode 100644 doc/board/thead/index.rst create mode 100644 doc/board/thead/lpi4a.rst create mode 100644 include/configs/th1520_lpi4a.h
Signature · 1 line
2.40.0
PATCH RESEND 1/4 riscv: t-head: licheepi4a: initial support added
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's TH1520 SoC, only minimal device tree and serial onsole are enabled, so it's capable of chain booting from T-HEAD's vendor u-boot.
--- arch/riscv/Kconfig | 5 ++++ board/thead/th1520_lpi4a/Kconfig | 42 ++++++++++++++++++++++++++++ board/thead/th1520_lpi4a/MAINTAINERS | 7 +++++ board/thead/th1520_lpi4a/Makefile | 5 ++++ board/thead/th1520_lpi4a/board.c | 14 ++++++++++ include/configs/th1520_lpi4a.h | 22 +++++++++++++++ 6 files changed, 95 insertions(+) create mode 100644 board/thead/th1520_lpi4a/Kconfig create mode 100644 board/thead/th1520_lpi4a/MAINTAINERS create mode 100644 board/thead/th1520_lpi4a/Makefile create mode 100644 board/thead/th1520_lpi4a/board.c create mode 100644 include/configs/th1520_lpi4a.h
arch/riscv/Kconfig +5 -0
@@ -27,6 +27,10 @@ config TARGET_SIFIVE_UNMATCHED config TARGET_STARFIVE_VISIONFIVE2 bool "Support StarFive VisionFive2 Board" +config TARGET_TH1520_LPI4A + bool "Support Sipeed's TH1520 Lichee PI 4A Board" + select SYS_CACHE_SHIFT_6 + config TARGET_SIPEED_MAIX bool "Support Sipeed Maix Board" select SYS_CACHE_SHIFT_6
@@ -66,6 +70,7 @@ source "board/emulation/qemu-riscv/Kconfig" source "board/microchip/mpfs_icicle/Kconfig" source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" +source "board/thead/th1520_lpi4a/Kconfig" source "board/openpiton/riscv64/Kconfig" source "board/sipeed/maix/Kconfig" source "board/starfive/visionfive2/Kconfig"
board/thead/th1520_lpi4a/Kconfig new file +42 -0
42 lines not on this page · raw message
board/thead/th1520_lpi4a/MAINTAINERS new file +7 -0
@@ -0,0 +1,7 @@ +Lichee PI 4A +M: Wei Fu <[email protected]> +M: Yixun Lan <[email protected]> +S: Maintained +F: board/thead/th1520_lpi4a/ +F: configs/th1520_lpi4a_defconfig +F: doc/board/thead/lpi4a.rst
board/thead/th1520_lpi4a/Makefile new file +5 -0
@@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (c) 2023, Yixun Lan <[email protected]> + +obj-y += board.o
board/thead/th1520_lpi4a/board.c new file +14 -0
@@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) 2023, Yixun Lan <[email protected]> +* +*/ + +#include <common.h> + +int board_init (void ) +{ +enable_caches (); + +return 0 ; +}
include/configs/th1520_lpi4a.h new file +22 -0
@@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (c) 2023 Yixun Lan <[email protected]> +* +*/ + +#ifndef __TH1520_LPI4A_H +#define __TH1520_LPI4A_H + +#include <linux/sizes.h> + +#define CFG_SYS_SDRAM_BASE 0x00000000 + +#define UART_BASE 0xffe7014000 +#define UART_REG_WIDTH 32 + +/* Environment options */ + +#define CFG_EXTRA_ENV_SETTINGS \ + "PS1=[LPi4A]# \0" + +#endif /* __TH1520_LPI4A_H */
Signature · 1 line
2.40.0
Re: [RESEND PATCH v1 1/4] riscv: t-head: licheepi4a: initial support added
Quoted 147 lines · Yixun Lan
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's TH1520 SoC, only minimal device tree and serial onsole are enabled, so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/Kconfig | 5 ++++ board/thead/th1520_lpi4a/Kconfig | 42 ++++++++++++++++++++++++++++ board/thead/th1520_lpi4a/MAINTAINERS | 7 +++++ board/thead/th1520_lpi4a/Makefile | 5 ++++ board/thead/th1520_lpi4a/board.c | 14 ++++++++++ include/configs/th1520_lpi4a.h | 22 +++++++++++++++ 6 files changed, 95 insertions(+) create mode 100644 board/thead/th1520_lpi4a/Kconfig create mode 100644 board/thead/th1520_lpi4a/MAINTAINERS create mode 100644 board/thead/th1520_lpi4a/Makefile create mode 100644 board/thead/th1520_lpi4a/board.c create mode 100644 include/configs/th1520_lpi4a.harch/riscv/Kconfig +5
-0@@ -27,6 +27,10 @@ config TARGET_SIFIVE_UNMATCHED config TARGET_STARFIVE_VISIONFIVE2 bool "Support StarFive VisionFive2 Board" +config TARGET_TH1520_LPI4A + bool "Support Sipeed's TH1520 Lichee PI 4A Board" + select SYS_CACHE_SHIFT_6 + config TARGET_SIPEED_MAIX bool "Support Sipeed Maix Board" select SYS_CACHE_SHIFT_6@@ -66,6 +70,7 @@ source "board/emulation/qemu-riscv/Kconfig" source "board/microchip/mpfs_icicle/Kconfig" source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" +source "board/thead/th1520_lpi4a/Kconfig" source "board/openpiton/riscv64/Kconfig" source "board/sipeed/maix/Kconfig" source "board/starfive/visionfive2/Kconfig"board/thead/th1520_lpi4a/Kconfig new file +42
-0@@ -0,0 +1,42 @@ +if TARGET_TH1520_LPI4A + +config ARCH_THEAD + bool + default y + +config SYS_BOARD + default "th1520_lpi4a" + +config SYS_VENDOR + default "thead" + +config SYS_CPU + default "generic" + +config SYS_CONFIG_NAME + default "th1520_lpi4a" + +config TEXT_BASE + default 0x01b00000 if SPL + default 0x01c00000 if !RISCV_SMODE + default 0x01c00000 if RISCV_SMODE + +config SPL_TEXT_BASE + default 0x08000000 + +config SPL_OPENSBI_LOAD_ADDR + default 0x80000000 + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select ARCH_EARLY_INIT_R + imply CPU + imply CPU_RISCV + imply RISCV_TIMER if RISCV_SMODE + imply CMD_CPU + imply SMP + imply SUPPORT_OF_CONTROL + imply OF_CONTROL + imply OF_REAL + +endifboard/thead/th1520_lpi4a/MAINTAINERS new file +7
-0@@ -0,0 +1,7 @@ +Lichee PI 4A +M: Wei Fu <[email protected]> +M: Yixun Lan <[email protected]> +S: Maintained +F: board/thead/th1520_lpi4a/ +F: configs/th1520_lpi4a_defconfig +F: doc/board/thead/lpi4a.rstboard/thead/th1520_lpi4a/Makefile new file +5
-0@@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (c) 2023, Yixun Lan <[email protected]> + +obj-y += board.oboard/thead/th1520_lpi4a/board.c new file +14
-0@@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) 2023, Yixun Lan <[email protected]> +* +*/ + +#include <common.h> + +int board_init (void ) +{ +enable_caches (); + +return 0 ; +}include/configs/th1520_lpi4a.h new file +5
-0@@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (c) 2023 Yixun Lan <[email protected]> +* +*/
include/configs/th1520_lpi4a.h line 15
Quoted 10 lines
include/configs/th1520_lpi4a.h new file +10
-0+ +#ifndef __TH1520_LPI4A_H +#define __TH1520_LPI4A_H + +#include <linux/sizes.h> + +#define CFG_SYS_SDRAM_BASE 0x00000000 + +#define UART_BASE 0xffe7014000 +#define UART_REG_WIDTH 32
why couldn't we get it from dts? just like opensbi.
Quoted 10 lines
include/configs/th1520_lpi4a.h new file +7
-1+ +/* Environment options */ + +#define CFG_EXTRA_ENV_SETTINGS \ + "PS1=[LPi4A]# \0" + +#endif /* __TH1520_LPI4A_H */ --2.40.0
Signature · 2 lines
Best Regards Guo Ren
Re: [RESEND PATCH v1 1/4] riscv: t-head: licheepi4a: initial support added
Hi Guo:
Quoted 151 lines · Guo Ren
Quoted 150 lines · Yixun Lan
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's TH1520 SoC, only minimal device tree and serial onsole are enabled, so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/Kconfig | 5 ++++ board/thead/th1520_lpi4a/Kconfig | 42 ++++++++++++++++++++++++++++ board/thead/th1520_lpi4a/MAINTAINERS | 7 +++++ board/thead/th1520_lpi4a/Makefile | 5 ++++ board/thead/th1520_lpi4a/board.c | 14 ++++++++++ include/configs/th1520_lpi4a.h | 22 +++++++++++++++ 6 files changed, 95 insertions(+) create mode 100644 board/thead/th1520_lpi4a/Kconfig create mode 100644 board/thead/th1520_lpi4a/MAINTAINERS create mode 100644 board/thead/th1520_lpi4a/Makefile create mode 100644 board/thead/th1520_lpi4a/board.c create mode 100644 include/configs/th1520_lpi4a.harch/riscv/Kconfig +5
-0@@ -27,6 +27,10 @@ config TARGET_SIFIVE_UNMATCHED config TARGET_STARFIVE_VISIONFIVE2 bool "Support StarFive VisionFive2 Board" +config TARGET_TH1520_LPI4A + bool "Support Sipeed's TH1520 Lichee PI 4A Board" + select SYS_CACHE_SHIFT_6 + config TARGET_SIPEED_MAIX bool "Support Sipeed Maix Board" select SYS_CACHE_SHIFT_6@@ -66,6 +70,7 @@ source "board/emulation/qemu-riscv/Kconfig" source "board/microchip/mpfs_icicle/Kconfig" source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" +source "board/thead/th1520_lpi4a/Kconfig" source "board/openpiton/riscv64/Kconfig" source "board/sipeed/maix/Kconfig" source "board/starfive/visionfive2/Kconfig"board/thead/th1520_lpi4a/Kconfig new file +42
-0@@ -0,0 +1,42 @@ +if TARGET_TH1520_LPI4A + +config ARCH_THEAD + bool + default y + +config SYS_BOARD + default "th1520_lpi4a" + +config SYS_VENDOR + default "thead" + +config SYS_CPU + default "generic" + +config SYS_CONFIG_NAME + default "th1520_lpi4a" + +config TEXT_BASE + default 0x01b00000 if SPL + default 0x01c00000 if !RISCV_SMODE + default 0x01c00000 if RISCV_SMODE + +config SPL_TEXT_BASE + default 0x08000000 + +config SPL_OPENSBI_LOAD_ADDR + default 0x80000000 + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select ARCH_EARLY_INIT_R + imply CPU + imply CPU_RISCV + imply RISCV_TIMER if RISCV_SMODE + imply CMD_CPU + imply SMP + imply SUPPORT_OF_CONTROL + imply OF_CONTROL + imply OF_REAL + +endifboard/thead/th1520_lpi4a/MAINTAINERS new file +7
-0@@ -0,0 +1,7 @@ +Lichee PI 4A +M: Wei Fu <[email protected]> +M: Yixun Lan <[email protected]> +S: Maintained +F: board/thead/th1520_lpi4a/ +F: configs/th1520_lpi4a_defconfig +F: doc/board/thead/lpi4a.rstboard/thead/th1520_lpi4a/Makefile new file +5
-0@@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (c) 2023, Yixun Lan <[email protected]> + +obj-y += board.oboard/thead/th1520_lpi4a/board.c new file +14
-0@@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) 2023, Yixun Lan <[email protected]> +* +*/ + +#include <common.h> + +int board_init (void ) +{ +enable_caches (); + +return 0 ; +}include/configs/th1520_lpi4a.h new file +8
-0@@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (c) 2023 Yixun Lan <[email protected]> +* +*/ + +#ifndef __TH1520_LPI4A_H +#define __TH1520_LPI4A_H
Quoted 9 lines
include/configs/th1520_lpi4a.h line 15
Quoted 7 lines
include/configs/th1520_lpi4a.h new file +7
-0+ +#include <linux/sizes.h> + +#define CFG_SYS_SDRAM_BASE 0x00000000 + +#define UART_BASE 0xffe7014000 +#define UART_REG_WIDTH 32why couldn't we get it from dts? just like opensbi.
good catch! exactly these can be removed, I will fix in v2
Quoted 15 lines
Quoted 10 lines
include/configs/th1520_lpi4a.h new file +7
-1+ +/* Environment options */ + +#define CFG_EXTRA_ENV_SETTINGS \ + "PS1=[LPi4A]# \0" + +#endif /* __TH1520_LPI4A_H */ --2.40.0
Signature · 2 lines
Best Regards Guo Ren
Signature · 3 lines
Yixun Lan (dlan) Gentoo Linux Developer GPG Key ID AABEFD55
Re: [RESEND PATCH v1 1/4] riscv: t-head: licheepi4a: initial support added
In reply to Yixun LanQuoted 51 lines · Yixun Lan
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's TH1520 SoC, only minimal device tree and serial onsole are enabled, so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/Kconfig | 5 ++++ board/thead/th1520_lpi4a/Kconfig | 42 ++++++++++++++++++++++++++++ board/thead/th1520_lpi4a/MAINTAINERS | 7 +++++ board/thead/th1520_lpi4a/Makefile | 5 ++++ board/thead/th1520_lpi4a/board.c | 14 ++++++++++ include/configs/th1520_lpi4a.h | 22 +++++++++++++++ 6 files changed, 95 insertions(+) create mode 100644 board/thead/th1520_lpi4a/Kconfig create mode 100644 board/thead/th1520_lpi4a/MAINTAINERS create mode 100644 board/thead/th1520_lpi4a/Makefile create mode 100644 board/thead/th1520_lpi4a/board.c create mode 100644 include/configs/th1520_lpi4a.harch/riscv/Kconfig +5
-0@@ -27,6 +27,10 @@ config TARGET_SIFIVE_UNMATCHED config TARGET_STARFIVE_VISIONFIVE2 bool "Support StarFive VisionFive2 Board" +config TARGET_TH1520_LPI4A + bool "Support Sipeed's TH1520 Lichee PI 4A Board" + select SYS_CACHE_SHIFT_6 + config TARGET_SIPEED_MAIX bool "Support Sipeed Maix Board" select SYS_CACHE_SHIFT_6@@ -66,6 +70,7 @@ source "board/emulation/qemu-riscv/Kconfig" source "board/microchip/mpfs_icicle/Kconfig" source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" +source "board/thead/th1520_lpi4a/Kconfig" source "board/openpiton/riscv64/Kconfig" source "board/sipeed/maix/Kconfig" source "board/starfive/visionfive2/Kconfig"board/thead/th1520_lpi4a/Kconfig new file +1
-0@@ -0,0 +1,42 @@ +if TARGET_TH1520_LPI4A
board/thead/th1520_lpi4a/Kconfig line 11
Quoted 10 lines
board/thead/th1520_lpi4a/Kconfig new file +10
-0+ +config ARCH_THEAD + bool + default y + +config SYS_BOARD + default "th1520_lpi4a" + +config SYS_VENDOR + default "thread"
default "T-HEAD"
Thx
Quoted 106 lines
board/thead/th1520_lpi4a/Kconfig new file +31
-0+ +config SYS_CPU + default "generic" + +config SYS_CONFIG_NAME + default "th1520_lpi4a" + +config TEXT_BASE + default 0x01b00000 if SPL + default 0x01c00000 if !RISCV_SMODE + default 0x01c00000 if RISCV_SMODE + +config SPL_TEXT_BASE + default 0x08000000 + +config SPL_OPENSBI_LOAD_ADDR + default 0x80000000 + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select ARCH_EARLY_INIT_R + imply CPU + imply CPU_RISCV + imply RISCV_TIMER if RISCV_SMODE + imply CMD_CPU + imply SMP + imply SUPPORT_OF_CONTROL + imply OF_CONTROL + imply OF_REAL + +endifboard/thead/th1520_lpi4a/MAINTAINERS new file +7
-0@@ -0,0 +1,7 @@ +Lichee PI 4A +M: Wei Fu <[email protected]> +M: Yixun Lan <[email protected]> +S: Maintained +F: board/thead/th1520_lpi4a/ +F: configs/th1520_lpi4a_defconfig +F: doc/board/thead/lpi4a.rstboard/thead/th1520_lpi4a/Makefile new file +5
-0@@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (c) 2023, Yixun Lan <[email protected]> + +obj-y += board.oboard/thead/th1520_lpi4a/board.c new file +14
-0@@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) 2023, Yixun Lan <[email protected]> +* +*/ + +#include <common.h> + +int board_init (void ) +{ +enable_caches (); + +return 0 ; +}include/configs/th1520_lpi4a.h new file +22
-1@@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (c) 2023 Yixun Lan <[email protected]> +* +*/ + +#ifndef __TH1520_LPI4A_H +#define __TH1520_LPI4A_H + +#include <linux/sizes.h> + +#define CFG_SYS_SDRAM_BASE 0x00000000 + +#define UART_BASE 0xffe7014000 +#define UART_REG_WIDTH 32 + +/* Environment options */ + +#define CFG_EXTRA_ENV_SETTINGS \ + "PS1=[LPi4A]# \0" + +#endif /* __TH1520_LPI4A_H */ --2.40.0
Signature · 2 lines
Best Regards Guo Ren
Re: [RESEND PATCH v1 1/4] riscv: t-head: licheepi4a: initial support added
Hi Guo, Jisheng:
Quoted 51 lines · Guo Ren
Quoted 50 lines · Yixun Lan
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's TH1520 SoC, only minimal device tree and serial onsole are enabled, so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/Kconfig | 5 ++++ board/thead/th1520_lpi4a/Kconfig | 42 ++++++++++++++++++++++++++++ board/thead/th1520_lpi4a/MAINTAINERS | 7 +++++ board/thead/th1520_lpi4a/Makefile | 5 ++++ board/thead/th1520_lpi4a/board.c | 14 ++++++++++ include/configs/th1520_lpi4a.h | 22 +++++++++++++++ 6 files changed, 95 insertions(+) create mode 100644 board/thead/th1520_lpi4a/Kconfig create mode 100644 board/thead/th1520_lpi4a/MAINTAINERS create mode 100644 board/thead/th1520_lpi4a/Makefile create mode 100644 board/thead/th1520_lpi4a/board.c create mode 100644 include/configs/th1520_lpi4a.harch/riscv/Kconfig +5
-0@@ -27,6 +27,10 @@ config TARGET_SIFIVE_UNMATCHED config TARGET_STARFIVE_VISIONFIVE2 bool "Support StarFive VisionFive2 Board" +config TARGET_TH1520_LPI4A + bool "Support Sipeed's TH1520 Lichee PI 4A Board" + select SYS_CACHE_SHIFT_6 + config TARGET_SIPEED_MAIX bool "Support Sipeed Maix Board" select SYS_CACHE_SHIFT_6@@ -66,6 +70,7 @@ source "board/emulation/qemu-riscv/Kconfig" source "board/microchip/mpfs_icicle/Kconfig" source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" +source "board/thead/th1520_lpi4a/Kconfig" source "board/openpiton/riscv64/Kconfig" source "board/sipeed/maix/Kconfig" source "board/starfive/visionfive2/Kconfig"board/thead/th1520_lpi4a/Kconfig new file +0
-0@@ -0,0 +1,42 @@
Quoted 8 lines
board/thead/th1520_lpi4a/Kconfig line 8
Quoted 8 lines
board/thead/th1520_lpi4a/Kconfig new file +8
-0+if TARGET_TH1520_LPI4A + +config ARCH_THEAD + bool + default y + +config SYS_BOARD + default "th1520_lpi4a"
for the board, I'm not sure whether people will prefer to keep the 'th1520_' prefix, otherwise we could make it shorter, leave only 'lpi4a'? thoughts?
Quoted 3 lines
board/thead/th1520_lpi4a/Kconfig
Quoted 3 lines
board/thead/th1520_lpi4a/Kconfig new file +3
-0+ +config SYS_VENDOR + default "thread"
~~~~~~~ notice, in my original patch, it's 'thead'
Quoted 1 line
default "T-HEAD"
No, here should be 'thead', since the CONFIG_SYS_VENDOR will form board/${CONFIG_SYS_VENDOR}, please consult arch/Kconfig for reference.
I personally would prefer 't-head' which probably cause less confusion.. but since kernel use 'thead'[1], so I just follow it to keep them aligned.
[1] in kernel, the dts path consist of 'thead', e.g. arch/riscv/boot/dts/thead/
Quoted 113 lines
Thx
Quoted 106 lines
board/thead/th1520_lpi4a/Kconfig new file +31
-0+ +config SYS_CPU + default "generic" + +config SYS_CONFIG_NAME + default "th1520_lpi4a" + +config TEXT_BASE + default 0x01b00000 if SPL + default 0x01c00000 if !RISCV_SMODE + default 0x01c00000 if RISCV_SMODE + +config SPL_TEXT_BASE + default 0x08000000 + +config SPL_OPENSBI_LOAD_ADDR + default 0x80000000 + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select ARCH_EARLY_INIT_R + imply CPU + imply CPU_RISCV + imply RISCV_TIMER if RISCV_SMODE + imply CMD_CPU + imply SMP + imply SUPPORT_OF_CONTROL + imply OF_CONTROL + imply OF_REAL + +endifboard/thead/th1520_lpi4a/MAINTAINERS new file +7
-0@@ -0,0 +1,7 @@ +Lichee PI 4A +M: Wei Fu <[email protected]> +M: Yixun Lan <[email protected]> +S: Maintained +F: board/thead/th1520_lpi4a/ +F: configs/th1520_lpi4a_defconfig +F: doc/board/thead/lpi4a.rstboard/thead/th1520_lpi4a/Makefile new file +5
-0@@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (c) 2023, Yixun Lan <[email protected]> + +obj-y += board.oboard/thead/th1520_lpi4a/board.c new file +14
-0@@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) 2023, Yixun Lan <[email protected]> +* +*/ + +#include <common.h> + +int board_init (void ) +{ +enable_caches (); + +return 0 ; +}include/configs/th1520_lpi4a.h new file +22
-1@@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (c) 2023 Yixun Lan <[email protected]> +* +*/ + +#ifndef __TH1520_LPI4A_H +#define __TH1520_LPI4A_H + +#include <linux/sizes.h> + +#define CFG_SYS_SDRAM_BASE 0x00000000 + +#define UART_BASE 0xffe7014000 +#define UART_REG_WIDTH 32 + +/* Environment options */ + +#define CFG_EXTRA_ENV_SETTINGS \ + "PS1=[LPi4A]# \0" + +#endif /* __TH1520_LPI4A_H */ --2.40.0
Signature · 2 lines
Best Regards Guo Ren
Signature · 3 lines
Yixun Lan (dlan) Gentoo Linux Developer GPG Key ID AABEFD55
Re: [RESEND PATCH v1 1/4] riscv: t-head: licheepi4a: initial support added
Quoted 70 lines · Yixun Lan
Hi Guo, Jisheng:
Quoted 51 lines · Guo Ren
Quoted 50 lines · Yixun Lan
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's TH1520 SoC, only minimal device tree and serial onsole are enabled, so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/Kconfig | 5 ++++ board/thead/th1520_lpi4a/Kconfig | 42 ++++++++++++++++++++++++++++ board/thead/th1520_lpi4a/MAINTAINERS | 7 +++++ board/thead/th1520_lpi4a/Makefile | 5 ++++ board/thead/th1520_lpi4a/board.c | 14 ++++++++++ include/configs/th1520_lpi4a.h | 22 +++++++++++++++ 6 files changed, 95 insertions(+) create mode 100644 board/thead/th1520_lpi4a/Kconfig create mode 100644 board/thead/th1520_lpi4a/MAINTAINERS create mode 100644 board/thead/th1520_lpi4a/Makefile create mode 100644 board/thead/th1520_lpi4a/board.c create mode 100644 include/configs/th1520_lpi4a.harch/riscv/Kconfig +5
-0@@ -27,6 +27,10 @@ config TARGET_SIFIVE_UNMATCHED config TARGET_STARFIVE_VISIONFIVE2 bool "Support StarFive VisionFive2 Board" +config TARGET_TH1520_LPI4A + bool "Support Sipeed's TH1520 Lichee PI 4A Board" + select SYS_CACHE_SHIFT_6 + config TARGET_SIPEED_MAIX bool "Support Sipeed Maix Board" select SYS_CACHE_SHIFT_6@@ -66,6 +70,7 @@ source "board/emulation/qemu-riscv/Kconfig" source "board/microchip/mpfs_icicle/Kconfig" source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" +source "board/thead/th1520_lpi4a/Kconfig" source "board/openpiton/riscv64/Kconfig" source "board/sipeed/maix/Kconfig" source "board/starfive/visionfive2/Kconfig"board/thead/th1520_lpi4a/Kconfig new file +0
-0@@ -0,0 +1,42 @@Quoted 8 lines
board/thead/th1520_lpi4a/Kconfig line 8
Quoted 8 lines
board/thead/th1520_lpi4a/Kconfig new file +8
-0+if TARGET_TH1520_LPI4A + +config ARCH_THEAD + bool + default y + +config SYS_BOARD + default "th1520_lpi4a"for the board, I'm not sure whether people will prefer to keep the '
th1520_' prefix, otherwise we could make it shorter, leave only 'lpi4a'? thoughts?Quoted 3 lines
board/thead/th1520_lpi4a/Kconfig
Quoted 3 lines
board/thead/th1520_lpi4a/Kconfig new file +3
-0+ +config SYS_VENDOR + default "thread"~~~~~~~ notice, in my original patch, it's 'thead'
Quoted 7 lines
Quoted 1 line
default "T-HEAD"
No, here should be 'thead', since the
CONFIG_SYS_VENDORwill form board/${CONFIG_SYS_VENDOR}, please consultarch/Kconfigfor reference.I personally would prefer 't-head' which probably cause less confusion.. but since kernel use 'thead'[1], so I just follow it to keep them aligned.
But you have a typo here :)
Quoted 2 lines
[1] in kernel, the dts path consist of 'thead', e.g.
arch/riscv/boot/dts/thead/
Regards,
Bin
Re: [RESEND PATCH v1 1/4] riscv: t-head: licheepi4a: initial support added
Hi Bin:
Quoted 72 lines · Bin Meng
Quoted 71 lines · Yixun Lan
Hi Guo, Jisheng:
Quoted 51 lines · Guo Ren
Quoted 50 lines · Yixun Lan
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's TH1520 SoC, only minimal device tree and serial onsole are enabled, so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/Kconfig | 5 ++++ board/thead/th1520_lpi4a/Kconfig | 42 ++++++++++++++++++++++++++++ board/thead/th1520_lpi4a/MAINTAINERS | 7 +++++ board/thead/th1520_lpi4a/Makefile | 5 ++++ board/thead/th1520_lpi4a/board.c | 14 ++++++++++ include/configs/th1520_lpi4a.h | 22 +++++++++++++++ 6 files changed, 95 insertions(+) create mode 100644 board/thead/th1520_lpi4a/Kconfig create mode 100644 board/thead/th1520_lpi4a/MAINTAINERS create mode 100644 board/thead/th1520_lpi4a/Makefile create mode 100644 board/thead/th1520_lpi4a/board.c create mode 100644 include/configs/th1520_lpi4a.harch/riscv/Kconfig +5
-0@@ -27,6 +27,10 @@ config TARGET_SIFIVE_UNMATCHED config TARGET_STARFIVE_VISIONFIVE2 bool "Support StarFive VisionFive2 Board" +config TARGET_TH1520_LPI4A + bool "Support Sipeed's TH1520 Lichee PI 4A Board" + select SYS_CACHE_SHIFT_6 + config TARGET_SIPEED_MAIX bool "Support Sipeed Maix Board" select SYS_CACHE_SHIFT_6@@ -66,6 +70,7 @@ source "board/emulation/qemu-riscv/Kconfig" source "board/microchip/mpfs_icicle/Kconfig" source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" +source "board/thead/th1520_lpi4a/Kconfig" source "board/openpiton/riscv64/Kconfig" source "board/sipeed/maix/Kconfig" source "board/starfive/visionfive2/Kconfig"board/thead/th1520_lpi4a/Kconfig new file +0
-0@@ -0,0 +1,42 @@Quoted 8 lines
board/thead/th1520_lpi4a/Kconfig line 8
Quoted 8 lines
board/thead/th1520_lpi4a/Kconfig new file +8
-0+if TARGET_TH1520_LPI4A + +config ARCH_THEAD + bool + default y + +config SYS_BOARD + default "th1520_lpi4a"for the board, I'm not sure whether people will prefer to keep the '
th1520_' prefix, otherwise we could make it shorter, leave only 'lpi4a'? thoughts?Quoted 3 lines
board/thead/th1520_lpi4a/Kconfig
Quoted 3 lines
board/thead/th1520_lpi4a/Kconfig new file +3
-0+ +config SYS_VENDOR + default "thread"~~~~~~~ notice, in my original patch, it's 'thead'
Quoted 1 line
default "T-HEAD"
Quoted 8 lines
Quoted 6 lines
No, here should be 'thead', since the
CONFIG_SYS_VENDORwill form board/${CONFIG_SYS_VENDOR}, please consultarch/Kconfigfor reference.I personally would prefer 't-head' which probably cause less confusion.. but since kernel use 'thead'[1], so I just follow it to keep them aligned.
But you have a typo here :)
do you mean 'thread'? It's 'thead' actually in my original patch, so no typo.. I was already trying to clarify this.
It's probably a grammar correction when Guo reply the email
https://lore.kernel.org/all/[email protected]/
Quoted 6 lines
Quoted 3 lines
[1] in kernel, the dts path consist of 'thead', e.g.
arch/riscv/boot/dts/thead/Regards,
Bin
Signature · 3 lines
Yixun Lan (dlan) Gentoo Linux Developer GPG Key ID AABEFD55
Re: [RESEND PATCH v1 1/4] riscv: t-head: licheepi4a: initial support added
Quoted 83 lines · Yixun Lan
Hi Bin:
Quoted 79 lines · Bin Meng
Quoted 77 lines · Yixun Lan
Hi Guo, Jisheng:
Quoted 51 lines · Guo Ren
Quoted 50 lines · Yixun Lan
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's TH1520 SoC, only minimal device tree and serial onsole are enabled, so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/Kconfig | 5 ++++ board/thead/th1520_lpi4a/Kconfig | 42 ++++++++++++++++++++++++++++ board/thead/th1520_lpi4a/MAINTAINERS | 7 +++++ board/thead/th1520_lpi4a/Makefile | 5 ++++ board/thead/th1520_lpi4a/board.c | 14 ++++++++++ include/configs/th1520_lpi4a.h | 22 +++++++++++++++ 6 files changed, 95 insertions(+) create mode 100644 board/thead/th1520_lpi4a/Kconfig create mode 100644 board/thead/th1520_lpi4a/MAINTAINERS create mode 100644 board/thead/th1520_lpi4a/Makefile create mode 100644 board/thead/th1520_lpi4a/board.c create mode 100644 include/configs/th1520_lpi4a.harch/riscv/Kconfig +5
-0@@ -27,6 +27,10 @@ config TARGET_SIFIVE_UNMATCHED config TARGET_STARFIVE_VISIONFIVE2 bool "Support StarFive VisionFive2 Board" +config TARGET_TH1520_LPI4A + bool "Support Sipeed's TH1520 Lichee PI 4A Board" + select SYS_CACHE_SHIFT_6 + config TARGET_SIPEED_MAIX bool "Support Sipeed Maix Board" select SYS_CACHE_SHIFT_6@@ -66,6 +70,7 @@ source "board/emulation/qemu-riscv/Kconfig" source "board/microchip/mpfs_icicle/Kconfig" source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" +source "board/thead/th1520_lpi4a/Kconfig" source "board/openpiton/riscv64/Kconfig" source "board/sipeed/maix/Kconfig" source "board/starfive/visionfive2/Kconfig"board/thead/th1520_lpi4a/Kconfig new file +0
-0@@ -0,0 +1,42 @@Quoted 8 lines
board/thead/th1520_lpi4a/Kconfig line 8
Quoted 8 lines
board/thead/th1520_lpi4a/Kconfig new file +8
-0+if TARGET_TH1520_LPI4A + +config ARCH_THEAD + bool + default y + +config SYS_BOARD + default "th1520_lpi4a"for the board, I'm not sure whether people will prefer to keep the '
th1520_' prefix, otherwise we could make it shorter, leave only 'lpi4a'? thoughts?Quoted 3 lines
board/thead/th1520_lpi4a/Kconfig
Quoted 3 lines
board/thead/th1520_lpi4a/Kconfig new file +3
-0+ +config SYS_VENDOR + default "thread"~~~~~~~ notice, in my original patch, it's 'thead'
Quoted 1 line
default "T-HEAD"
No, here should be 'thead', since the
CONFIG_SYS_VENDORwill form board/${CONFIG_SYS_VENDOR}, please consultarch/Kconfigfor reference.I personally would prefer 't-head' which probably cause less confusion.. but since kernel use 'thead'[1], so I just follow it to keep them aligned.
Quoted 9 lines
Quoted 1 line
But you have a typo here :)
do you mean 'thread'? It's 'thead' actually in my original patch, so no typo.. I was already trying to clarify this.
It's probably a grammar correction when Guo reply the email
https://lore.kernel.org/all/[email protected]/
Quoted 2 lines
Quoted 2 lines
[1] in kernel, the dts path consist of 'thead', e.g.
arch/riscv/boot/dts/thead/
I see. Thanks for the clarification!
Regards,
Bin
Re: [RESEND PATCH v1 1/4] riscv: t-head: licheepi4a: initial support added
In reply to Yixun LanHi YiXun,
Quoted 14 lines · Yixun Lan
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's TH1520 SoC, only minimal device tree and serial onsole are enabled, so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>...
board/thead/th1520_lpi4a/board.c new file +1
-0@@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0+
board/thead/th1520_lpi4a/board.c line 11
Quoted 10 lines
board/thead/th1520_lpi4a/board.c new file +10
-0+/* +* Copyright (c) 2023, Yixun Lan <[email protected]> +* +*/ + +#include <common.h> + +int board_init (void ) +{ +enable_caches ();
There is a compilation warining here at "enable_caches" (probably due to cpu_func.h not being included to provide this function)
Best regards,
Leo
Quoted 3 lines
board/thead/th1520_lpi4a/board.c new file +3
-0+ +return 0 ; +}
Re: [RESEND PATCH v1 1/4] riscv: t-head: licheepi4a: initial support added
Hi Leo
Quoted 21 lines · Leo Liang
Hi YiXun,
Quoted 19 lines · Yixun Lan
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's TH1520 SoC, only minimal device tree and serial onsole are enabled, so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>...
board/thead/th1520_lpi4a/board.c new file +6
-0@@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) 2023, Yixun Lan <[email protected]> +* +*/ +
Quoted 9 lines
board/thead/th1520_lpi4a/board.c line 11
Quoted 5 lines
board/thead/th1520_lpi4a/board.c new file +5
-0+#include <common.h> + +int board_init (void ) +{ +enable_caches ();There is a compilation warining here at "
enable_caches" (probably due tocpu_func.hnot being included to provide this function)
thanks, will fix in v2
Quoted 6 lines
Best regards,
LeoQuoted 3 lines
board/thead/th1520_lpi4a/board.c new file +3
-0+ +return 0 ; +}
Signature · 3 lines
Yixun Lan (dlan) Gentoo Linux Developer GPG Key ID AABEFD55
PATCH RESEND 2/4 riscv: dts: t-head: Add basic device tree for Sipeed Lichee PI 4A board
In reply to Yixun LanOnly add basic support for CPU, PLIC UART and Timer.
--- arch/riscv/dts/Makefile | 1 + arch/riscv/dts/th1520-lichee-module-4a.dtsi | 34 ++ arch/riscv/dts/th1520-lichee-pi-4a.dts | 32 ++ arch/riscv/dts/th1520.dtsi | 435 ++++++++++++++++++++ 4 files changed, 502 insertions(+) create mode 100644 arch/riscv/dts/th1520-lichee-module-4a.dtsi create mode 100644 arch/riscv/dts/th1520-lichee-pi-4a.dts create mode 100644 arch/riscv/dts/th1520.dtsi
arch/riscv/dts/Makefile +1 -0
@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) += hifive-unmatched-a00.dtb dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.3b.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb include $(srctree)/scripts/Makefile.dts targets += $(dtb-y)
arch/riscv/dts/th1520-lichee-module-4a.dtsi new file +34 -0
@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +/dts-v1/; + +#include "th1520.dtsi" + +/ { + model = "Sipeed Lichee Module 4A"; + compatible = "sipeed,lichee-module-4a", "thead,th1520"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; +}; + +&osc { + clock-frequency = <24000000>; +}; + +&osc_32k { + clock-frequency = <32768>; +}; + +&apb_clk { + clock-frequency = <62500000>; +}; + +&uart_sclk { + clock-frequency = <100000000>; +};
arch/riscv/dts/th1520-lichee-pi-4a.dts new file +32 -0
@@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include "th1520-lichee-module-4a.dtsi" + +/ { + model = "Sipeed Lichee Pi 4A"; + compatible = "sipeed,lichee-pi-4a", "sipeed,lichee-module-4a", "thead,th1520"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +};
arch/riscv/dts/th1520.dtsi new file +435 -0
435 lines not on this page · raw message
Signature · 1 line
2.40.0
Re: [RESEND PATCH v1 2/4] riscv: dts: t-head: Add basic device tree for Sipeed Lichee PI 4A board
Sorry, why we need dts here? If we put dts here, we could delete the one in Linux.
We shouldn't put it with two places, that would be bad for maintanice.
Quoted 272 lines · Yixun Lan
Only add basic support for CPU, PLIC UART and Timer.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/dts/Makefile | 1 + arch/riscv/dts/th1520-lichee-module-4a.dtsi | 34 ++ arch/riscv/dts/th1520-lichee-pi-4a.dts | 32 ++ arch/riscv/dts/th1520.dtsi | 435 ++++++++++++++++++++ 4 files changed, 502 insertions(+) create mode 100644 arch/riscv/dts/th1520-lichee-module-4a.dtsi create mode 100644 arch/riscv/dts/th1520-lichee-pi-4a.dts create mode 100644 arch/riscv/dts/th1520.dtsiarch/riscv/dts/Makefile +1
-0@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) += hifive-unmatched-a00.dtb dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.3b.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb include $(srctree)/scripts/Makefile.dts targets += $(dtb-y)arch/riscv/dts/th1520-lichee-module-4a.dtsi new file +34
-0@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +/dts-v1/; + +#include "th1520.dtsi" + +/ { + model = "Sipeed Lichee Module 4A"; + compatible = "sipeed,lichee-module-4a", "thead,th1520"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; +}; + +&osc { + clock-frequency = <24000000>; +}; + +&osc_32k { + clock-frequency = <32768>; +}; + +&apb_clk { + clock-frequency = <62500000>; +}; + +&uart_sclk { + clock-frequency = <100000000>; +};arch/riscv/dts/th1520-lichee-pi-4a.dts new file +32
-0@@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include "th1520-lichee-module-4a.dtsi" + +/ { + model = "Sipeed Lichee Pi 4A"; + compatible = "sipeed,lichee-pi-4a", "sipeed,lichee-module-4a", "thead,th1520"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +};arch/riscv/dts/th1520.dtsi new file +161
-0@@ -0,0 +1,435 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Alibaba Group Holding Limited. + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + compatible = "thead,th1520"; + #address-cells = <2>; + #size-cells = <2>; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <3000000>; + + c910_0: cpu@0 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <0>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_1: cpu@1 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <1>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu1_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_2: cpu@2 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <2>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu2_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_3: cpu@3 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <3>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu3_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&c910_0>; + }; + + core1 { + cpu = <&c910_1>; + }; + + core2 { + cpu = <&c910_2>; + }; + + core3 { + cpu = <&c910_3>; + }; + }; + }; + + l2_cache: l2-cache { + compatible = "cache"; + cache-block-size = <64>; + cache-level = <2>; + cache-size = <1048576>; + cache-sets = <1024>; + cache-unified; + }; + }; + + osc: oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_24m"; + #clock-cells = <0>; + }; + + osc_32k: 32k-oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_32k"; + #clock-cells = <0>; + }; + + apb_clk: apb-clk-clock { + compatible = "fixed-clock"; + clock-output-names = "apb_clk"; + #clock-cells = <0>; + }; + + uart_sclk: uart-sclk-clock { + compatible = "fixed-clock"; + clock-output-names = "uart_sclk"; + #clock-cells = <0>; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>;
arch/riscv/dts/th1520.dtsi line 171
Quoted 10 lines
arch/riscv/dts/th1520.dtsi new file +10
-0+ ranges; + + cpurst: cpurst { + compatible = "thead,reset-th1520"; + entry-reg = <0xff 0xff019050>; + entry-cnt = <4>; + control-reg = <0xff 0xff015004>; + control-val = <0x1c>; + csr-copy = <0x7f3 0x7c0 0x7c1 0x7c2 0x7c3 0x7c5 0x7cc>; + };
This part has been changed.
Quoted 267 lines
arch/riscv/dts/th1520.dtsi new file +264
-1+ + plic: interrupt-controller@ffd8000000 { + compatible = "thead,th1520-plic", "thead,c900-plic"; + reg = <0xff 0xd8000000 0x0 0x01000000>; + interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>, + <&cpu1_intc 11>, <&cpu1_intc 9>, + <&cpu2_intc 11>, <&cpu2_intc 9>, + <&cpu3_intc 11>, <&cpu3_intc 9>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + riscv,ndev = <240>; + }; + + clint: timer@ffdc000000 { + compatible = "thead,th1520-clint", "thead,c900-clint"; + reg = <0xff 0xdc000000 0x0 0x00010000>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>, + <&cpu2_intc 3>, <&cpu2_intc 7>, + <&cpu3_intc 3>, <&cpu3_intc 7>; + }; + + uart0: serial@ffe7014000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7014000 0x0 0x4000>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: serial@ffe7f00000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f00000 0x0 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart3: serial@ffe7f04000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f04000 0x0 0x4000>; + interrupts = <39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + gpio2: gpio@ffe7f34000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f34000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portc: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <58 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio3: gpio@ffe7f38000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f38000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portd: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <59 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio0: gpio@ffec005000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec005000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <56 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio1: gpio@ffec006000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec006000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portb: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <57 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + uart2: serial@ffec010000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xec010000 0x0 0x4000>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer0: timer@ffefc32000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer1: timer@ffefc32014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer2: timer@ffefc32028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer3: timer@ffefc3203c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc3203c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart4: serial@fff7f08000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f08000 0x0 0x4000>; + interrupts = <40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart5: serial@fff7f0c000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f0c000 0x0 0x4000>; + interrupts = <41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer4: timer@ffffc33000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer5: timer@ffffc33014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer6: timer@ffffc33028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer7: timer@ffffc3303c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc3303c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + ao_gpio0: gpio@fffff41000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff41000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porte: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <76 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + ao_gpio1: gpio@fffff52000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff52000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portf: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; +}; --2.40.0
Signature · 2 lines
Best Regards Guo Ren
Re: [RESEND PATCH v1 2/4] riscv: dts: t-head: Add basic device tree for Sipeed Lichee PI 4A board
Hi Guo:
Quoted 2 lines · Guo Ren
Sorry, why we need dts here? If we put dts here, we could delete the one in Linux.
No, I think it's more than a historical reason for why we have two dts both in u-boot and kernel. And this dts here is merely used by u-boot, it could be a simplified version comparing to kernel's dts.
Quoted 2 lines
We shouldn't put it with two places, that would be bad for maintanice.
I can totally understand your concern, in fact, we are trying to keep them sync, so I will probably wait the dts of kernel settle down, before take action here. so, please conside this patch as RFC, and may change in next revisions..
Quoted 277 lines · Yixun Lan
Quoted 275 lines
Only add basic support for CPU, PLIC UART and Timer.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/dts/Makefile | 1 + arch/riscv/dts/th1520-lichee-module-4a.dtsi | 34 ++ arch/riscv/dts/th1520-lichee-pi-4a.dts | 32 ++ arch/riscv/dts/th1520.dtsi | 435 ++++++++++++++++++++ 4 files changed, 502 insertions(+) create mode 100644 arch/riscv/dts/th1520-lichee-module-4a.dtsi create mode 100644 arch/riscv/dts/th1520-lichee-pi-4a.dts create mode 100644 arch/riscv/dts/th1520.dtsiarch/riscv/dts/Makefile +1
-0@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) += hifive-unmatched-a00.dtb dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.3b.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb include $(srctree)/scripts/Makefile.dts targets += $(dtb-y)arch/riscv/dts/th1520-lichee-module-4a.dtsi new file +34
-0@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +/dts-v1/; + +#include "th1520.dtsi" + +/ { + model = "Sipeed Lichee Module 4A"; + compatible = "sipeed,lichee-module-4a", "thead,th1520"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; +}; + +&osc { + clock-frequency = <24000000>; +}; + +&osc_32k { + clock-frequency = <32768>; +}; + +&apb_clk { + clock-frequency = <62500000>; +}; + +&uart_sclk { + clock-frequency = <100000000>; +};arch/riscv/dts/th1520-lichee-pi-4a.dts new file +32
-0@@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include "th1520-lichee-module-4a.dtsi" + +/ { + model = "Sipeed Lichee Pi 4A"; + compatible = "sipeed,lichee-pi-4a", "sipeed,lichee-module-4a", "thead,th1520"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +};arch/riscv/dts/th1520.dtsi new file +164
-0@@ -0,0 +1,435 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Alibaba Group Holding Limited. + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + compatible = "thead,th1520"; + #address-cells = <2>; + #size-cells = <2>; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <3000000>; + + c910_0: cpu@0 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <0>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_1: cpu@1 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <1>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu1_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_2: cpu@2 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <2>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu2_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_3: cpu@3 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <3>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu3_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&c910_0>; + }; + + core1 { + cpu = <&c910_1>; + }; + + core2 { + cpu = <&c910_2>; + }; + + core3 { + cpu = <&c910_3>; + }; + }; + }; + + l2_cache: l2-cache { + compatible = "cache"; + cache-block-size = <64>; + cache-level = <2>; + cache-size = <1048576>; + cache-sets = <1024>; + cache-unified; + }; + }; + + osc: oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_24m"; + #clock-cells = <0>; + }; + + osc_32k: 32k-oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_32k"; + #clock-cells = <0>; + }; + + apb_clk: apb-clk-clock { + compatible = "fixed-clock"; + clock-output-names = "apb_clk"; + #clock-cells = <0>; + }; + + uart_sclk: uart-sclk-clock { + compatible = "fixed-clock"; + clock-output-names = "uart_sclk"; + #clock-cells = <0>; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + cpurst: cpurst {
Quoted 9 lines
arch/riscv/dts/th1520.dtsi line 171
Quoted 7 lines
arch/riscv/dts/th1520.dtsi new file +7
-0+ compatible = "thead,reset-th1520"; + entry-reg = <0xff 0xff019050>; + entry-cnt = <4>; + control-reg = <0xff 0xff015004>; + control-val = <0x1c>; + csr-copy = <0x7f3 0x7c0 0x7c1 0x7c2 0x7c3 0x7c5 0x7cc>; + };This part has been changed.
noted, will update accordingly
Quoted 272 lines
Quoted 267 lines
arch/riscv/dts/th1520.dtsi new file +264
-1+ + plic: interrupt-controller@ffd8000000 { + compatible = "thead,th1520-plic", "thead,c900-plic"; + reg = <0xff 0xd8000000 0x0 0x01000000>; + interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>, + <&cpu1_intc 11>, <&cpu1_intc 9>, + <&cpu2_intc 11>, <&cpu2_intc 9>, + <&cpu3_intc 11>, <&cpu3_intc 9>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + riscv,ndev = <240>; + }; + + clint: timer@ffdc000000 { + compatible = "thead,th1520-clint", "thead,c900-clint"; + reg = <0xff 0xdc000000 0x0 0x00010000>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>, + <&cpu2_intc 3>, <&cpu2_intc 7>, + <&cpu3_intc 3>, <&cpu3_intc 7>; + }; + + uart0: serial@ffe7014000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7014000 0x0 0x4000>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: serial@ffe7f00000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f00000 0x0 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart3: serial@ffe7f04000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f04000 0x0 0x4000>; + interrupts = <39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + gpio2: gpio@ffe7f34000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f34000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portc: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <58 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio3: gpio@ffe7f38000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f38000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portd: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <59 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio0: gpio@ffec005000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec005000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <56 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio1: gpio@ffec006000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec006000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portb: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <57 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + uart2: serial@ffec010000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xec010000 0x0 0x4000>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer0: timer@ffefc32000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer1: timer@ffefc32014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer2: timer@ffefc32028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer3: timer@ffefc3203c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc3203c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart4: serial@fff7f08000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f08000 0x0 0x4000>; + interrupts = <40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart5: serial@fff7f0c000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f0c000 0x0 0x4000>; + interrupts = <41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer4: timer@ffffc33000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer5: timer@ffffc33014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer6: timer@ffffc33028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer7: timer@ffffc3303c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc3303c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + ao_gpio0: gpio@fffff41000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff41000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porte: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <76 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + ao_gpio1: gpio@fffff52000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff52000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portf: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; +}; --2.40.0
Signature · 2 lines
Best Regards Guo Ren
Signature · 3 lines
Yixun Lan (dlan) Gentoo Linux Developer GPG Key ID AABEFD55
Re: [RESEND PATCH v1 2/4] riscv: dts: t-head: Add basic device tree for Sipeed Lichee PI 4A board
Quoted 11 lines · Yixun Lan
Hi Guo:
Quoted 2 lines · Guo Ren
Sorry, why we need dts here? If we put dts here, we could delete the one in Linux.
No, I think it's more than a historical reason for why we have two dts both in u-boot and kernel. And this dts here is merely used by u-boot, it could be a simplified version comparing to kernel's dts.
Quoted 1 line
Quoted 4 lines
Quoted 1 line
We shouldn't put it with two places, that would be bad for maintanice.
I can totally understand your concern, in fact, we are trying to keep them sync, so I will probably wait the dts of kernel settle down, before take action here. so, please conside this patch as RFC, and may change in next revisions..
Thx for clarification. But I still concern the necessary of the patch, could you move this from this series first, because we've argument on it. Your other patches looks good, I'm looking forward your next v2.
But for this one, let's talk it after kernel side merged.
Quoted 566 lines
Quoted 278 lines · Yixun Lan
Quoted 275 lines
Only add basic support for CPU, PLIC UART and Timer.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/dts/Makefile | 1 + arch/riscv/dts/th1520-lichee-module-4a.dtsi | 34 ++ arch/riscv/dts/th1520-lichee-pi-4a.dts | 32 ++ arch/riscv/dts/th1520.dtsi | 435 ++++++++++++++++++++ 4 files changed, 502 insertions(+) create mode 100644 arch/riscv/dts/th1520-lichee-module-4a.dtsi create mode 100644 arch/riscv/dts/th1520-lichee-pi-4a.dts create mode 100644 arch/riscv/dts/th1520.dtsiarch/riscv/dts/Makefile +1
-0@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) += hifive-unmatched-a00.dtb dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.3b.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb include $(srctree)/scripts/Makefile.dts targets += $(dtb-y)arch/riscv/dts/th1520-lichee-module-4a.dtsi new file +34
-0@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +/dts-v1/; + +#include "th1520.dtsi" + +/ { + model = "Sipeed Lichee Module 4A"; + compatible = "sipeed,lichee-module-4a", "thead,th1520"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; +}; + +&osc { + clock-frequency = <24000000>; +}; + +&osc_32k { + clock-frequency = <32768>; +}; + +&apb_clk { + clock-frequency = <62500000>; +}; + +&uart_sclk { + clock-frequency = <100000000>; +};arch/riscv/dts/th1520-lichee-pi-4a.dts new file +32
-0@@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include "th1520-lichee-module-4a.dtsi" + +/ { + model = "Sipeed Lichee Pi 4A"; + compatible = "sipeed,lichee-pi-4a", "sipeed,lichee-module-4a", "thead,th1520"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +};arch/riscv/dts/th1520.dtsi new file +164
-0@@ -0,0 +1,435 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Alibaba Group Holding Limited. + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + compatible = "thead,th1520"; + #address-cells = <2>; + #size-cells = <2>; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <3000000>; + + c910_0: cpu@0 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <0>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_1: cpu@1 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <1>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu1_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_2: cpu@2 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <2>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu2_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_3: cpu@3 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <3>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu3_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&c910_0>; + }; + + core1 { + cpu = <&c910_1>; + }; + + core2 { + cpu = <&c910_2>; + }; + + core3 { + cpu = <&c910_3>; + }; + }; + }; + + l2_cache: l2-cache { + compatible = "cache"; + cache-block-size = <64>; + cache-level = <2>; + cache-size = <1048576>; + cache-sets = <1024>; + cache-unified; + }; + }; + + osc: oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_24m"; + #clock-cells = <0>; + }; + + osc_32k: 32k-oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_32k"; + #clock-cells = <0>; + }; + + apb_clk: apb-clk-clock { + compatible = "fixed-clock"; + clock-output-names = "apb_clk"; + #clock-cells = <0>; + }; + + uart_sclk: uart-sclk-clock { + compatible = "fixed-clock"; + clock-output-names = "uart_sclk"; + #clock-cells = <0>; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + cpurst: cpurst {Quoted 9 lines
arch/riscv/dts/th1520.dtsi line 171
Quoted 7 lines
arch/riscv/dts/th1520.dtsi new file +7
-0+ compatible = "thead,reset-th1520"; + entry-reg = <0xff 0xff019050>; + entry-cnt = <4>; + control-reg = <0xff 0xff015004>; + control-val = <0x1c>; + csr-copy = <0x7f3 0x7c0 0x7c1 0x7c2 0x7c3 0x7c5 0x7cc>; + };This part has been changed.
noted, will update accordingly
Quoted 264 lines
Quoted 264 lines
arch/riscv/dts/th1520.dtsi new file +264
-0+ + plic: interrupt-controller@ffd8000000 { + compatible = "thead,th1520-plic", "thead,c900-plic"; + reg = <0xff 0xd8000000 0x0 0x01000000>; + interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>, + <&cpu1_intc 11>, <&cpu1_intc 9>, + <&cpu2_intc 11>, <&cpu2_intc 9>, + <&cpu3_intc 11>, <&cpu3_intc 9>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + riscv,ndev = <240>; + }; + + clint: timer@ffdc000000 { + compatible = "thead,th1520-clint", "thead,c900-clint"; + reg = <0xff 0xdc000000 0x0 0x00010000>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>, + <&cpu2_intc 3>, <&cpu2_intc 7>, + <&cpu3_intc 3>, <&cpu3_intc 7>; + }; + + uart0: serial@ffe7014000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7014000 0x0 0x4000>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: serial@ffe7f00000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f00000 0x0 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart3: serial@ffe7f04000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f04000 0x0 0x4000>; + interrupts = <39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + gpio2: gpio@ffe7f34000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f34000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portc: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <58 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio3: gpio@ffe7f38000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f38000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portd: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <59 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio0: gpio@ffec005000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec005000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <56 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio1: gpio@ffec006000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec006000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portb: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <57 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + uart2: serial@ffec010000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xec010000 0x0 0x4000>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer0: timer@ffefc32000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer1: timer@ffefc32014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer2: timer@ffefc32028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer3: timer@ffefc3203c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc3203c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart4: serial@fff7f08000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f08000 0x0 0x4000>; + interrupts = <40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart5: serial@fff7f0c000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f0c000 0x0 0x4000>; + interrupts = <41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer4: timer@ffffc33000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer5: timer@ffffc33014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer6: timer@ffffc33028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer7: timer@ffffc3303c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc3303c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + ao_gpio0: gpio@fffff41000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff41000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porte: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <76 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + ao_gpio1: gpio@fffff52000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff52000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portf: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; +};Quoted 8 lines
Quoted 3 lines
--
2.40.0--
Best Regards
Guo Ren--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55
Signature · 2 lines
Best Regards Guo Ren
Re: [RESEND PATCH v1 2/4] riscv: dts: t-head: Add basic device tree for Sipeed Lichee PI 4A board
Hi Guo:
see my comment below.
Quoted 13 lines · Guo Ren
Quoted 12 lines · Yixun Lan
Hi Guo:
Quoted 2 lines · Guo Ren
Sorry, why we need dts here? If we put dts here, we could delete the one in Linux.
No, I think it's more than a historical reason for why we have two dts both in u-boot and kernel. And this dts here is merely used by u-boot, it could be a simplified version comparing to kernel's dts.
Quoted 2 lines
We shouldn't put it with two places, that would be bad for maintanice.
Quoted 8 lines
Quoted 3 lines
I can totally understand your concern, in fact, we are trying to keep them sync, so I will probably wait the dts of kernel settle down, before take action here. so, please conside this patch as RFC, and may change in next revisions..
Thx for clarification. But I still concern the necessary of the patch, could you move this from this series first, because we've argument on it. Your other patches looks good, I'm looking forward your next v2.
But for this one, let's talk it after kernel side merged.
I'd like to include dts in the first series, otherwise it won't be a complete working series, e.g. - not only it's unable to build, also can't do run-time test
I'm totally fine with kernel dts merged first, then submit this later, so no push..
Quoted 573 lines
Quoted 567 lines
Quoted 279 lines · Yixun Lan
Quoted 275 lines
Only add basic support for CPU, PLIC UART and Timer.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/dts/Makefile | 1 + arch/riscv/dts/th1520-lichee-module-4a.dtsi | 34 ++ arch/riscv/dts/th1520-lichee-pi-4a.dts | 32 ++ arch/riscv/dts/th1520.dtsi | 435 ++++++++++++++++++++ 4 files changed, 502 insertions(+) create mode 100644 arch/riscv/dts/th1520-lichee-module-4a.dtsi create mode 100644 arch/riscv/dts/th1520-lichee-pi-4a.dts create mode 100644 arch/riscv/dts/th1520.dtsiarch/riscv/dts/Makefile +1
-0@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) += hifive-unmatched-a00.dtb dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.3b.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb include $(srctree)/scripts/Makefile.dts targets += $(dtb-y)arch/riscv/dts/th1520-lichee-module-4a.dtsi new file +34
-0@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +/dts-v1/; + +#include "th1520.dtsi" + +/ { + model = "Sipeed Lichee Module 4A"; + compatible = "sipeed,lichee-module-4a", "thead,th1520"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; +}; + +&osc { + clock-frequency = <24000000>; +}; + +&osc_32k { + clock-frequency = <32768>; +}; + +&apb_clk { + clock-frequency = <62500000>; +}; + +&uart_sclk { + clock-frequency = <100000000>; +};arch/riscv/dts/th1520-lichee-pi-4a.dts new file +32
-0@@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include "th1520-lichee-module-4a.dtsi" + +/ { + model = "Sipeed Lichee Pi 4A"; + compatible = "sipeed,lichee-pi-4a", "sipeed,lichee-module-4a", "thead,th1520"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +};arch/riscv/dts/th1520.dtsi new file +164
-0@@ -0,0 +1,435 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Alibaba Group Holding Limited. + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + compatible = "thead,th1520"; + #address-cells = <2>; + #size-cells = <2>; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <3000000>; + + c910_0: cpu@0 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <0>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_1: cpu@1 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <1>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu1_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_2: cpu@2 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <2>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu2_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_3: cpu@3 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <3>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu3_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&c910_0>; + }; + + core1 { + cpu = <&c910_1>; + }; + + core2 { + cpu = <&c910_2>; + }; + + core3 { + cpu = <&c910_3>; + }; + }; + }; + + l2_cache: l2-cache { + compatible = "cache"; + cache-block-size = <64>; + cache-level = <2>; + cache-size = <1048576>; + cache-sets = <1024>; + cache-unified; + }; + }; + + osc: oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_24m"; + #clock-cells = <0>; + }; + + osc_32k: 32k-oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_32k"; + #clock-cells = <0>; + }; + + apb_clk: apb-clk-clock { + compatible = "fixed-clock"; + clock-output-names = "apb_clk"; + #clock-cells = <0>; + }; + + uart_sclk: uart-sclk-clock { + compatible = "fixed-clock"; + clock-output-names = "uart_sclk"; + #clock-cells = <0>; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + cpurst: cpurst {Quoted 9 lines
arch/riscv/dts/th1520.dtsi line 171
Quoted 7 lines
arch/riscv/dts/th1520.dtsi new file +7
-0+ compatible = "thead,reset-th1520"; + entry-reg = <0xff 0xff019050>; + entry-cnt = <4>; + control-reg = <0xff 0xff015004>; + control-val = <0x1c>; + csr-copy = <0x7f3 0x7c0 0x7c1 0x7c2 0x7c3 0x7c5 0x7cc>; + };This part has been changed.
noted, will update accordingly
Quoted 264 lines
Quoted 264 lines
arch/riscv/dts/th1520.dtsi new file +264
-0+ + plic: interrupt-controller@ffd8000000 { + compatible = "thead,th1520-plic", "thead,c900-plic"; + reg = <0xff 0xd8000000 0x0 0x01000000>; + interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>, + <&cpu1_intc 11>, <&cpu1_intc 9>, + <&cpu2_intc 11>, <&cpu2_intc 9>, + <&cpu3_intc 11>, <&cpu3_intc 9>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + riscv,ndev = <240>; + }; + + clint: timer@ffdc000000 { + compatible = "thead,th1520-clint", "thead,c900-clint"; + reg = <0xff 0xdc000000 0x0 0x00010000>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>, + <&cpu2_intc 3>, <&cpu2_intc 7>, + <&cpu3_intc 3>, <&cpu3_intc 7>; + }; + + uart0: serial@ffe7014000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7014000 0x0 0x4000>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: serial@ffe7f00000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f00000 0x0 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart3: serial@ffe7f04000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f04000 0x0 0x4000>; + interrupts = <39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + gpio2: gpio@ffe7f34000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f34000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portc: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <58 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio3: gpio@ffe7f38000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f38000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portd: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <59 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio0: gpio@ffec005000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec005000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <56 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio1: gpio@ffec006000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec006000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portb: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <57 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + uart2: serial@ffec010000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xec010000 0x0 0x4000>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer0: timer@ffefc32000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer1: timer@ffefc32014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer2: timer@ffefc32028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer3: timer@ffefc3203c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc3203c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart4: serial@fff7f08000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f08000 0x0 0x4000>; + interrupts = <40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart5: serial@fff7f0c000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f0c000 0x0 0x4000>; + interrupts = <41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer4: timer@ffffc33000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer5: timer@ffffc33014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer6: timer@ffffc33028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer7: timer@ffffc3303c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc3303c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + ao_gpio0: gpio@fffff41000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff41000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porte: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <76 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + ao_gpio1: gpio@fffff52000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff52000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portf: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; +};Quoted 8 lines
Quoted 3 lines
--
2.40.0--
Best Regards
Guo Ren--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55Signature · 2 lines
Best Regards Guo Ren
Signature · 3 lines
Yixun Lan (dlan) Gentoo Linux Developer GPG Key ID AABEFD55
Re: [RESEND PATCH v1 2/4] riscv: dts: t-head: Add basic device tree for Sipeed Lichee PI 4A board
Quoted 22 lines · Yixun Lan
Hi Guo:
see my comment below.
Quoted 16 lines · Guo Ren
Quoted 15 lines · Yixun Lan
Hi Guo:
Quoted 2 lines · Guo Ren
Sorry, why we need dts here? If we put dts here, we could delete the one in Linux.
No, I think it's more than a historical reason for why we have two dts both in u-boot and kernel. And this dts here is merely used by u-boot, it could be a simplified version comparing to kernel's dts.
Quoted 2 lines
We shouldn't put it with two places, that would be bad for maintanice.
I can totally understand your concern, in fact, we are trying to keep them sync, so I will probably wait the dts of kernel settle down, before take action here. so, please conside this patch as RFC, and may change in next revisions..
Quoted 7 lines
Quoted 5 lines
Thx for clarification. But I still concern the necessary of the patch, could you move this from this series first, because we've argument on it. Your other patches looks good, I'm looking forward your next v2.
But for this one, let's talk it after kernel side merged.
I'd like to include dts in the first series, otherwise it won't be a complete working series, e.g. - not only it's unable to build, also can't do run-time test
I couldn't make sense how it block your build, The build operation is controlled by you Makefile modification. right?
arch/riscv/dts/Makefile +0 -0
@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) +=
hifive-unmatched-a00.dtb
dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) +=
jh7110-starfive-visionfive-2-v1.3b.dtb
dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) +=
jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb
include $(srctree)/scripts/Makefile.dts
Quoted 581 lines
I'm totally fine with kernel dts merged first, then submit this later, so no push..
Quoted 570 lines
Quoted 563 lines
Quoted 279 lines · Yixun Lan
Quoted 275 lines
Only add basic support for CPU, PLIC UART and Timer.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/dts/Makefile | 1 + arch/riscv/dts/th1520-lichee-module-4a.dtsi | 34 ++ arch/riscv/dts/th1520-lichee-pi-4a.dts | 32 ++ arch/riscv/dts/th1520.dtsi | 435 ++++++++++++++++++++ 4 files changed, 502 insertions(+) create mode 100644 arch/riscv/dts/th1520-lichee-module-4a.dtsi create mode 100644 arch/riscv/dts/th1520-lichee-pi-4a.dts create mode 100644 arch/riscv/dts/th1520.dtsiarch/riscv/dts/Makefile +1
-0@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) += hifive-unmatched-a00.dtb dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.3b.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb include $(srctree)/scripts/Makefile.dts targets += $(dtb-y)arch/riscv/dts/th1520-lichee-module-4a.dtsi new file +34
-0@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +/dts-v1/; + +#include "th1520.dtsi" + +/ { + model = "Sipeed Lichee Module 4A"; + compatible = "sipeed,lichee-module-4a", "thead,th1520"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; +}; + +&osc { + clock-frequency = <24000000>; +}; + +&osc_32k { + clock-frequency = <32768>; +}; + +&apb_clk { + clock-frequency = <62500000>; +}; + +&uart_sclk { + clock-frequency = <100000000>; +};arch/riscv/dts/th1520-lichee-pi-4a.dts new file +32
-0@@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include "th1520-lichee-module-4a.dtsi" + +/ { + model = "Sipeed Lichee Pi 4A"; + compatible = "sipeed,lichee-pi-4a", "sipeed,lichee-module-4a", "thead,th1520"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +};arch/riscv/dts/th1520.dtsi new file +164
-0@@ -0,0 +1,435 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Alibaba Group Holding Limited. + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + compatible = "thead,th1520"; + #address-cells = <2>; + #size-cells = <2>; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <3000000>; + + c910_0: cpu@0 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <0>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_1: cpu@1 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <1>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu1_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_2: cpu@2 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <2>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu2_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_3: cpu@3 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <3>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu3_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&c910_0>; + }; + + core1 { + cpu = <&c910_1>; + }; + + core2 { + cpu = <&c910_2>; + }; + + core3 { + cpu = <&c910_3>; + }; + }; + }; + + l2_cache: l2-cache { + compatible = "cache"; + cache-block-size = <64>; + cache-level = <2>; + cache-size = <1048576>; + cache-sets = <1024>; + cache-unified; + }; + }; + + osc: oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_24m"; + #clock-cells = <0>; + }; + + osc_32k: 32k-oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_32k"; + #clock-cells = <0>; + }; + + apb_clk: apb-clk-clock { + compatible = "fixed-clock"; + clock-output-names = "apb_clk"; + #clock-cells = <0>; + }; + + uart_sclk: uart-sclk-clock { + compatible = "fixed-clock"; + clock-output-names = "uart_sclk"; + #clock-cells = <0>; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + cpurst: cpurst {Quoted 9 lines
arch/riscv/dts/th1520.dtsi line 171
Quoted 7 lines
arch/riscv/dts/th1520.dtsi new file +7
-0+ compatible = "thead,reset-th1520"; + entry-reg = <0xff 0xff019050>; + entry-cnt = <4>; + control-reg = <0xff 0xff015004>; + control-val = <0x1c>; + csr-copy = <0x7f3 0x7c0 0x7c1 0x7c2 0x7c3 0x7c5 0x7cc>; + };This part has been changed.
noted, will update accordingly
Quoted 264 lines
Quoted 264 lines
arch/riscv/dts/th1520.dtsi new file +264
-0+ + plic: interrupt-controller@ffd8000000 { + compatible = "thead,th1520-plic", "thead,c900-plic"; + reg = <0xff 0xd8000000 0x0 0x01000000>; + interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>, + <&cpu1_intc 11>, <&cpu1_intc 9>, + <&cpu2_intc 11>, <&cpu2_intc 9>, + <&cpu3_intc 11>, <&cpu3_intc 9>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + riscv,ndev = <240>; + }; + + clint: timer@ffdc000000 { + compatible = "thead,th1520-clint", "thead,c900-clint"; + reg = <0xff 0xdc000000 0x0 0x00010000>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>, + <&cpu2_intc 3>, <&cpu2_intc 7>, + <&cpu3_intc 3>, <&cpu3_intc 7>; + }; + + uart0: serial@ffe7014000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7014000 0x0 0x4000>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: serial@ffe7f00000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f00000 0x0 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart3: serial@ffe7f04000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f04000 0x0 0x4000>; + interrupts = <39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + gpio2: gpio@ffe7f34000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f34000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portc: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <58 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio3: gpio@ffe7f38000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f38000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portd: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <59 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio0: gpio@ffec005000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec005000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <56 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio1: gpio@ffec006000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec006000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portb: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <57 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + uart2: serial@ffec010000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xec010000 0x0 0x4000>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer0: timer@ffefc32000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer1: timer@ffefc32014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer2: timer@ffefc32028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer3: timer@ffefc3203c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc3203c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart4: serial@fff7f08000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f08000 0x0 0x4000>; + interrupts = <40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart5: serial@fff7f0c000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f0c000 0x0 0x4000>; + interrupts = <41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer4: timer@ffffc33000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer5: timer@ffffc33014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer6: timer@ffffc33028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer7: timer@ffffc3303c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc3303c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + ao_gpio0: gpio@fffff41000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff41000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porte: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <76 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + ao_gpio1: gpio@fffff52000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff52000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portf: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; +};Quoted 8 lines
Quoted 3 lines
--
2.40.0--
Best Regards
Guo RenQuoted 4 lines
--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55Quoted 3 lines
--
Best Regards
Guo Ren--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55
Signature · 2 lines
Best Regards Guo Ren
Re: [RESEND PATCH v1 2/4] riscv: dts: t-head: Add basic device tree for Sipeed Lichee PI 4A board
Hi Guo:
Quoted 27 lines · Guo Ren
Quoted 26 lines · Yixun Lan
Hi Guo:
see my comment below.
Quoted 20 lines · Guo Ren
Quoted 11 lines · Yixun Lan
Hi Guo:
Quoted 2 lines · Guo Ren
Sorry, why we need dts here? If we put dts here, we could delete the one in Linux.
No, I think it's more than a historical reason for why we have two dts both in u-boot and kernel. And this dts here is merely used by u-boot, it could be a simplified version comparing to kernel's dts.
Quoted 1 line
Quoted 4 lines
Quoted 1 line
We shouldn't put it with two places, that would be bad for maintanice.
I can totally understand your concern, in fact, we are trying to keep them sync, so I will probably wait the dts of kernel settle down, before take action here. so, please conside this patch as RFC, and may change in next revisions..
Thx for clarification. But I still concern the necessary of the patch, could you move this from this series first, because we've argument on it. Your other patches looks good, I'm looking forward your next v2.
Quoted 6 lines
Quoted 3 lines
Quoted 1 line
But for this one, let's talk it after kernel side merged.
I'd like to include dts in the first series, otherwise it won't be a complete working series, e.g. - not only it's unable to build, also can't do run-time test
I couldn't make sense how it block your build, The build operation is controlled by you
Makefilemodification. right?
you mostly right, but in patch "[ 3/4 ] configs: th1520_lpi4a_defconfig: Add initial config", we will enable device tree, and require CONFIG_DEFAULT_DEVICE_TREE="th1520-lichee-pi-4a.dtb" to be provided, also since UART's base register is parsed from dts (run time), so I see no reason why the dts patch should be separated
Quoted 601 lines
arch/riscv/dts/Makefile +0
-0@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) +=hifive-unmatched-a00.dtb
dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) +=
jh7110-starfive-visionfive-2-v1.3b.dtb
dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) +=
jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb
include $(srctree)/scripts/Makefile.dtsQuoted 581 lines
I'm totally fine with kernel dts merged first, then submit this later, so no push..
Quoted 570 lines
Quoted 563 lines
Quoted 279 lines · Yixun Lan
Quoted 275 lines
Only add basic support for CPU, PLIC UART and Timer.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/dts/Makefile | 1 + arch/riscv/dts/th1520-lichee-module-4a.dtsi | 34 ++ arch/riscv/dts/th1520-lichee-pi-4a.dts | 32 ++ arch/riscv/dts/th1520.dtsi | 435 ++++++++++++++++++++ 4 files changed, 502 insertions(+) create mode 100644 arch/riscv/dts/th1520-lichee-module-4a.dtsi create mode 100644 arch/riscv/dts/th1520-lichee-pi-4a.dts create mode 100644 arch/riscv/dts/th1520.dtsiarch/riscv/dts/Makefile +1
-0@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) += hifive-unmatched-a00.dtb dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.3b.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb include $(srctree)/scripts/Makefile.dts targets += $(dtb-y)arch/riscv/dts/th1520-lichee-module-4a.dtsi new file +34
-0@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +/dts-v1/; + +#include "th1520.dtsi" + +/ { + model = "Sipeed Lichee Module 4A"; + compatible = "sipeed,lichee-module-4a", "thead,th1520"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; +}; + +&osc { + clock-frequency = <24000000>; +}; + +&osc_32k { + clock-frequency = <32768>; +}; + +&apb_clk { + clock-frequency = <62500000>; +}; + +&uart_sclk { + clock-frequency = <100000000>; +};arch/riscv/dts/th1520-lichee-pi-4a.dts new file +32
-0@@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include "th1520-lichee-module-4a.dtsi" + +/ { + model = "Sipeed Lichee Pi 4A"; + compatible = "sipeed,lichee-pi-4a", "sipeed,lichee-module-4a", "thead,th1520"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +};arch/riscv/dts/th1520.dtsi new file +164
-0@@ -0,0 +1,435 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Alibaba Group Holding Limited. + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + compatible = "thead,th1520"; + #address-cells = <2>; + #size-cells = <2>; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <3000000>; + + c910_0: cpu@0 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <0>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_1: cpu@1 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <1>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu1_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_2: cpu@2 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <2>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu2_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_3: cpu@3 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <3>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu3_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&c910_0>; + }; + + core1 { + cpu = <&c910_1>; + }; + + core2 { + cpu = <&c910_2>; + }; + + core3 { + cpu = <&c910_3>; + }; + }; + }; + + l2_cache: l2-cache { + compatible = "cache"; + cache-block-size = <64>; + cache-level = <2>; + cache-size = <1048576>; + cache-sets = <1024>; + cache-unified; + }; + }; + + osc: oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_24m"; + #clock-cells = <0>; + }; + + osc_32k: 32k-oscillator { + compatible = "fixed-clock"; + clock-output-names = "osc_32k"; + #clock-cells = <0>; + }; + + apb_clk: apb-clk-clock { + compatible = "fixed-clock"; + clock-output-names = "apb_clk"; + #clock-cells = <0>; + }; + + uart_sclk: uart-sclk-clock { + compatible = "fixed-clock"; + clock-output-names = "uart_sclk"; + #clock-cells = <0>; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + cpurst: cpurst {Quoted 9 lines
arch/riscv/dts/th1520.dtsi line 171
Quoted 7 lines
arch/riscv/dts/th1520.dtsi new file +7
-0+ compatible = "thead,reset-th1520"; + entry-reg = <0xff 0xff019050>; + entry-cnt = <4>; + control-reg = <0xff 0xff015004>; + control-val = <0x1c>; + csr-copy = <0x7f3 0x7c0 0x7c1 0x7c2 0x7c3 0x7c5 0x7cc>; + };This part has been changed.
noted, will update accordingly
Quoted 264 lines
Quoted 264 lines
arch/riscv/dts/th1520.dtsi new file +264
-0+ + plic: interrupt-controller@ffd8000000 { + compatible = "thead,th1520-plic", "thead,c900-plic"; + reg = <0xff 0xd8000000 0x0 0x01000000>; + interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>, + <&cpu1_intc 11>, <&cpu1_intc 9>, + <&cpu2_intc 11>, <&cpu2_intc 9>, + <&cpu3_intc 11>, <&cpu3_intc 9>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + riscv,ndev = <240>; + }; + + clint: timer@ffdc000000 { + compatible = "thead,th1520-clint", "thead,c900-clint"; + reg = <0xff 0xdc000000 0x0 0x00010000>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>, + <&cpu2_intc 3>, <&cpu2_intc 7>, + <&cpu3_intc 3>, <&cpu3_intc 7>; + }; + + uart0: serial@ffe7014000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7014000 0x0 0x4000>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: serial@ffe7f00000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f00000 0x0 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart3: serial@ffe7f04000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f04000 0x0 0x4000>; + interrupts = <39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + gpio2: gpio@ffe7f34000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f34000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portc: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <58 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio3: gpio@ffe7f38000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f38000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portd: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <59 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio0: gpio@ffec005000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec005000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <56 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio1: gpio@ffec006000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec006000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portb: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <57 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + uart2: serial@ffec010000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xec010000 0x0 0x4000>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer0: timer@ffefc32000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer1: timer@ffefc32014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer2: timer@ffefc32028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer3: timer@ffefc3203c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc3203c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart4: serial@fff7f08000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f08000 0x0 0x4000>; + interrupts = <40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart5: serial@fff7f0c000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f0c000 0x0 0x4000>; + interrupts = <41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer4: timer@ffffc33000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer5: timer@ffffc33014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer6: timer@ffffc33028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer7: timer@ffffc3303c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc3303c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + ao_gpio0: gpio@fffff41000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff41000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porte: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <76 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + ao_gpio1: gpio@fffff52000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff52000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portf: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; +};Quoted 8 lines
Quoted 3 lines
--
2.40.0--
Best Regards
Guo RenQuoted 4 lines
--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55Quoted 3 lines
--
Best Regards
Guo Ren--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55Signature · 2 lines
Best Regards Guo Ren
Signature · 3 lines
Yixun Lan (dlan) Gentoo Linux Developer GPG Key ID AABEFD55
Re: [RESEND PATCH v1 2/4] riscv: dts: t-head: Add basic device tree for Sipeed Lichee PI 4A board
Quoted 34 lines · Yixun Lan
Hi Guo:
Quoted 30 lines · Guo Ren
Quoted 29 lines · Yixun Lan
Hi Guo:
see my comment below.
Quoted 13 lines · Guo Ren
Quoted 12 lines · Yixun Lan
Hi Guo:
Quoted 2 lines · Guo Ren
Sorry, why we need dts here? If we put dts here, we could delete the one in Linux.
No, I think it's more than a historical reason for why we have two dts both in u-boot and kernel. And this dts here is merely used by u-boot, it could be a simplified version comparing to kernel's dts.
Quoted 2 lines
We shouldn't put it with two places, that would be bad for maintanice.
Quoted 8 lines
Quoted 3 lines
I can totally understand your concern, in fact, we are trying to keep them sync, so I will probably wait the dts of kernel settle down, before take action here. so, please conside this patch as RFC, and may change in next revisions..
Thx for clarification. But I still concern the necessary of the patch, could you move this from this series first, because we've argument on it. Your other patches looks good, I'm looking forward your next v2.
But for this one, let's talk it after kernel side merged.
I'd like to include dts in the first series, otherwise it won't be a complete working series, e.g. - not only it's unable to build, also can't do run-time test
Quoted 8 lines
Quoted 3 lines
I couldn't make sense how it block your build, The build operation is controlled by you
Makefilemodification. right?you mostly right, but in patch "[ 3/4 ] configs:
th1520_lpi4a_defconfig: Add initial config", we will enable device tree, and requireCONFIG_DEFAULT_DEVICE_TREE="th1520-lichee-pi-4a.dtb" to be provided, also since UART's base register is parsed from dts (run time), so I see no reason why the dts patch should be separated
Oh, I see; u-boot needs a seperate dtb to boot indepedent. Maybe, we just keep a minimum dts here, then we needn't syncronize with the kernel side.
Quoted 139 lines
Quoted 139 lines
arch/riscv/dts/Makefile +0
-0@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) +=hifive-unmatched-a00.dtb
dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) +=
jh7110-starfive-visionfive-2-v1.3b.dtb
dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) +=
jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb
include $(srctree)/scripts/Makefile.dtsQuoted 124 lines
I'm totally fine with kernel dts merged first, then submit this later, so no push..
Quoted 121 lines
Quoted 121 lines
Quoted 121 lines · Yixun Lan
Quoted 117 lines
Only add basic support for CPU, PLIC UART and Timer.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/dts/Makefile | 1 + arch/riscv/dts/th1520-lichee-module-4a.dtsi | 34 ++ arch/riscv/dts/th1520-lichee-pi-4a.dts | 32 ++ arch/riscv/dts/th1520.dtsi | 435 ++++++++++++++++++++ 4 files changed, 502 insertions(+) create mode 100644 arch/riscv/dts/th1520-lichee-module-4a.dtsi create mode 100644 arch/riscv/dts/th1520-lichee-pi-4a.dts create mode 100644 arch/riscv/dts/th1520.dtsiarch/riscv/dts/Makefile +1
-0@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) += hifive-unmatched-a00.dtb dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.3b.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb include $(srctree)/scripts/Makefile.dts targets += $(dtb-y)arch/riscv/dts/th1520-lichee-module-4a.dtsi new file +34
-0@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +/dts-v1/; + +#include "th1520.dtsi" + +/ { + model = "Sipeed Lichee Module 4A"; + compatible = "sipeed,lichee-module-4a", "thead,th1520"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; +}; + +&osc { + clock-frequency = <24000000>; +}; + +&osc_32k { + clock-frequency = <32768>; +}; + +&apb_clk { + clock-frequency = <62500000>; +}; + +&uart_sclk { + clock-frequency = <100000000>; +};arch/riscv/dts/th1520-lichee-pi-4a.dts new file +32
-0@@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include "th1520-lichee-module-4a.dtsi" + +/ { + model = "Sipeed Lichee Pi 4A"; + compatible = "sipeed,lichee-pi-4a", "sipeed,lichee-module-4a", "thead,th1520"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +};arch/riscv/dts/th1520.dtsi new file +6
-0@@ -0,0 +1,435 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Alibaba Group Holding Limited. + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ +
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
arch/riscv/dts/th1520.dtsi line 14
Quoted 8 lines
arch/riscv/dts/th1520.dtsi new file +8
-0+#include <dt-bindings/interrupt-controller/irq.h> + +/ { + compatible = "thead,th1520"; + #address-cells = <2>; + #size-cells = <2>; + + cpus: cpus {
We needn't multi-cpus definitions.
Quoted 101 lines
Quoted 101 lines
Quoted 101 lines
Quoted 101 lines
Quoted 101 lines
Quoted 101 lines
Quoted 101 lines
arch/riscv/dts/th1520.dtsi new file +101
-0+ #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <3000000>; + + c910_0: cpu@0 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <0>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_1: cpu@1 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <1>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu1_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_2: cpu@2 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <2>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu2_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_3: cpu@3 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <3>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu3_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&c910_0>; + }; + + core1 { + cpu = <&c910_1>; + }; + + core2 { + cpu = <&c910_2>; + };
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
arch/riscv/dts/th1520.dtsi line 123
Quoted 8 lines
arch/riscv/dts/th1520.dtsi new file +8
-0+ + core3 { + cpu = <&c910_3>; + }; + }; + }; + + l2_cache: l2-cache {
We also needn't l2_cache description for u-boot.
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
arch/riscv/dts/th1520.dtsi line 133
Quoted 10 lines
arch/riscv/dts/th1520.dtsi new file +10
-0+ compatible = "cache"; + cache-block-size = <64>; + cache-level = <2>; + cache-size = <1048576>; + cache-sets = <1024>; + cache-unified; + }; + }; + + osc: oscillator {
Does u-boot need it?
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
arch/riscv/dts/th1520.dtsi line 139
Quoted 6 lines
arch/riscv/dts/th1520.dtsi new file +6
-0+ compatible = "fixed-clock"; + clock-output-names = "osc_24m"; + #clock-cells = <0>; + }; + + osc_32k: 32k-oscillator {
Does u-boot need it?
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
arch/riscv/dts/th1520.dtsi line 145
Quoted 6 lines
arch/riscv/dts/th1520.dtsi new file +6
-0+ compatible = "fixed-clock"; + clock-output-names = "osc_32k"; + #clock-cells = <0>; + }; + + apb_clk: apb-clk-clock {
Does u-boot need it?
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
arch/riscv/dts/th1520.dtsi new file +11
-0+ compatible = "fixed-clock"; + clock-output-names = "apb_clk"; + #clock-cells = <0>; + }; + + uart_sclk: uart-sclk-clock { + compatible = "fixed-clock"; + clock-output-names = "uart_sclk"; + #clock-cells = <0>; + }; +
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
arch/riscv/dts/th1520.dtsi line 164
Quoted 8 lines
arch/riscv/dts/th1520.dtsi new file +8
-0+ soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + cpurst: cpurst {
The u-boot needn't it
Quoted 75 lines
Quoted 75 lines
Quoted 75 lines
Quoted 75 lines
Quoted 75 lines
Quoted 9 lines
arch/riscv/dts/th1520.dtsi line 171
Quoted 7 lines
arch/riscv/dts/th1520.dtsi new file +7
-0+ compatible = "thead,reset-th1520"; + entry-reg = <0xff 0xff019050>; + entry-cnt = <4>; + control-reg = <0xff 0xff015004>; + control-val = <0x1c>; + csr-copy = <0x7f3 0x7c0 0x7c1 0x7c2 0x7c3 0x7c5 0x7cc>; + };This part has been changed.
noted, will update accordingly
Quoted 64 lines
Quoted 64 lines
arch/riscv/dts/th1520.dtsi new file +64
-0+ + plic: interrupt-controller@ffd8000000 { + compatible = "thead,th1520-plic", "thead,c900-plic"; + reg = <0xff 0xd8000000 0x0 0x01000000>; + interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>, + <&cpu1_intc 11>, <&cpu1_intc 9>, + <&cpu2_intc 11>, <&cpu2_intc 9>, + <&cpu3_intc 11>, <&cpu3_intc 9>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + riscv,ndev = <240>; + }; + + clint: timer@ffdc000000 { + compatible = "thead,th1520-clint", "thead,c900-clint"; + reg = <0xff 0xdc000000 0x0 0x00010000>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>, + <&cpu2_intc 3>, <&cpu2_intc 7>, + <&cpu3_intc 3>, <&cpu3_intc 7>; + }; + + uart0: serial@ffe7014000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7014000 0x0 0x4000>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: serial@ffe7f00000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f00000 0x0 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart3: serial@ffe7f04000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f04000 0x0 0x4000>; + interrupts = <39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + gpio2: gpio@ffe7f34000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f34000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portc: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>;
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
arch/riscv/dts/th1520.dtsi line 243
Quoted 8 lines
arch/riscv/dts/th1520.dtsi new file +8
-0+ reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <58 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio3: gpio@ffe7f38000 {
Do we enable the gpio driver in u-boot?
Quoted 227 lines
Quoted 219 lines
Quoted 208 lines
Quoted 208 lines
Quoted 205 lines
Quoted 192 lines
Quoted 192 lines
arch/riscv/dts/th1520.dtsi new file +192
-0+ compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f38000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portd: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <59 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio0: gpio@ffec005000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec005000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <56 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio1: gpio@ffec006000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec006000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portb: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <57 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + uart2: serial@ffec010000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xec010000 0x0 0x4000>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer0: timer@ffefc32000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer1: timer@ffefc32014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer2: timer@ffefc32028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer3: timer@ffefc3203c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc3203c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart4: serial@fff7f08000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f08000 0x0 0x4000>; + interrupts = <40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart5: serial@fff7f0c000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f0c000 0x0 0x4000>; + interrupts = <41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer4: timer@ffffc33000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer5: timer@ffffc33014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer6: timer@ffffc33028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer7: timer@ffffc3303c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc3303c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + ao_gpio0: gpio@fffff41000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff41000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porte: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <76 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + ao_gpio1: gpio@fffff52000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff52000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portf: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; +};Quoted 8 lines
Quoted 3 lines
--
2.40.0--
Best Regards
Guo Ren--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55Quoted 8 lines
Quoted 3 lines
--
Best Regards
Guo Ren--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55Quoted 3 lines
--
Best Regards
Guo Ren--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55
Signature · 2 lines
Best Regards Guo Ren
Re: [RESEND PATCH v1 2/4] riscv: dts: t-head: Add basic device tree for Sipeed Lichee PI 4A board
Hi Guo:
Quoted 38 lines · Guo Ren
Quoted 37 lines · Yixun Lan
Hi Guo:
Quoted 33 lines · Guo Ren
Quoted 22 lines · Yixun Lan
Hi Guo:
see my comment below.
Quoted 16 lines · Guo Ren
Quoted 15 lines · Yixun Lan
Hi Guo:
Quoted 2 lines · Guo Ren
Sorry, why we need dts here? If we put dts here, we could delete the one in Linux.
No, I think it's more than a historical reason for why we have two dts both in u-boot and kernel. And this dts here is merely used by u-boot, it could be a simplified version comparing to kernel's dts.
Quoted 2 lines
We shouldn't put it with two places, that would be bad for maintanice.
I can totally understand your concern, in fact, we are trying to keep them sync, so I will probably wait the dts of kernel settle down, before take action here. so, please conside this patch as RFC, and may change in next revisions..
Quoted 7 lines
Quoted 5 lines
Thx for clarification. But I still concern the necessary of the patch, could you move this from this series first, because we've argument on it. Your other patches looks good, I'm looking forward your next v2.
But for this one, let's talk it after kernel side merged.
I'd like to include dts in the first series, otherwise it won't be a complete working series, e.g. - not only it's unable to build, also can't do run-time test
I couldn't make sense how it block your build, The build operation is controlled by you
Makefilemodification. right?
Quoted 9 lines
Quoted 5 lines
you mostly right, but in patch "[ 3/4 ] configs:
th1520_lpi4a_defconfig: Add initial config", we will enable device tree, and requireCONFIG_DEFAULT_DEVICE_TREE="th1520-lichee-pi-4a.dtb" to be provided, also since UART's base register is parsed from dts (run time), so I see no reason why the dts patch should be separatedOh, I see; u-boot needs a seperate dtb to boot indepedent. Maybe, we just keep a minimum dts here, then we needn't syncronize with the kernel side.
yes, that's the plan, we will keep necessary dts here, and try to keep it sync with kernel when needed..
Quoted 621 lines
Quoted 139 lines
Quoted 139 lines
arch/riscv/dts/Makefile +0
-0@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) +=hifive-unmatched-a00.dtb
dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) +=
jh7110-starfive-visionfive-2-v1.3b.dtb
dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) +=
jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb
include $(srctree)/scripts/Makefile.dtsQuoted 124 lines
I'm totally fine with kernel dts merged first, then submit this later, so no push..
Quoted 121 lines
Quoted 121 lines
Quoted 121 lines · Yixun Lan
Quoted 117 lines
Only add basic support for CPU, PLIC UART and Timer.
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- arch/riscv/dts/Makefile | 1 + arch/riscv/dts/th1520-lichee-module-4a.dtsi | 34 ++ arch/riscv/dts/th1520-lichee-pi-4a.dts | 32 ++ arch/riscv/dts/th1520.dtsi | 435 ++++++++++++++++++++ 4 files changed, 502 insertions(+) create mode 100644 arch/riscv/dts/th1520-lichee-module-4a.dtsi create mode 100644 arch/riscv/dts/th1520-lichee-pi-4a.dts create mode 100644 arch/riscv/dts/th1520.dtsiarch/riscv/dts/Makefile +1
-0@@ -9,6 +9,7 @@ dtb-$(CONFIG_TARGET_SIFIVE_UNMATCHED) += hifive-unmatched-a00.dtb dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.3b.dtb dtb-$(CONFIG_TARGET_STARFIVE_VISIONFIVE2) += jh7110-starfive-visionfive-2-v1.2a.dtb +dtb-$(CONFIG_TARGET_TH1520_LPI4A) += th1520-lichee-pi-4a.dtb include $(srctree)/scripts/Makefile.dts targets += $(dtb-y)arch/riscv/dts/th1520-lichee-module-4a.dtsi new file +34
-0@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +/dts-v1/; + +#include "th1520.dtsi" + +/ { + model = "Sipeed Lichee Module 4A"; + compatible = "sipeed,lichee-module-4a", "thead,th1520"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; +}; + +&osc { + clock-frequency = <24000000>; +}; + +&osc_32k { + clock-frequency = <32768>; +}; + +&apb_clk { + clock-frequency = <62500000>; +}; + +&uart_sclk { + clock-frequency = <100000000>; +};arch/riscv/dts/th1520-lichee-pi-4a.dts new file +32
-0@@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ + +#include "th1520-lichee-module-4a.dtsi" + +/ { + model = "Sipeed Lichee Pi 4A"; + compatible = "sipeed,lichee-pi-4a", "sipeed,lichee-module-4a", "thead,th1520"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + status = "okay"; +};arch/riscv/dts/th1520.dtsi new file +6
-0@@ -0,0 +1,435 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Alibaba Group Holding Limited. + * Copyright (C) 2023 Jisheng Zhang <[email protected]> + */ +Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
arch/riscv/dts/th1520.dtsi line 14
Quoted 8 lines
arch/riscv/dts/th1520.dtsi new file +8
-0+#include <dt-bindings/interrupt-controller/irq.h> + +/ { + compatible = "thead,th1520"; + #address-cells = <2>; + #size-cells = <2>; + + cpus: cpus {We needn't multi-cpus definitions.
Quoted 101 lines
Quoted 101 lines
Quoted 101 lines
Quoted 101 lines
Quoted 101 lines
Quoted 101 lines
Quoted 101 lines
arch/riscv/dts/th1520.dtsi new file +101
-0+ #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <3000000>; + + c910_0: cpu@0 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <0>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_1: cpu@1 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <1>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu1_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_2: cpu@2 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <2>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu2_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + c910_3: cpu@3 { + compatible = "thead,c910", "riscv"; + device_type = "cpu"; + riscv,isa = "rv64imafdc"; + reg = <3>; + i-cache-block-size = <64>; + i-cache-size = <65536>; + i-cache-sets = <512>; + d-cache-block-size = <64>; + d-cache-size = <65536>; + d-cache-sets = <512>; + next-level-cache = <&l2_cache>; + mmu-type = "riscv,sv39"; + + cpu3_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&c910_0>; + }; + + core1 { + cpu = <&c910_1>; + }; + + core2 { + cpu = <&c910_2>; + };Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
arch/riscv/dts/th1520.dtsi line 123
Quoted 8 lines
arch/riscv/dts/th1520.dtsi new file +8
-0+ + core3 { + cpu = <&c910_3>; + }; + }; + }; + + l2_cache: l2-cache {We also needn't
l2_cachedescription for u-boot.Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
arch/riscv/dts/th1520.dtsi line 133
Quoted 10 lines
arch/riscv/dts/th1520.dtsi new file +10
-0+ compatible = "cache"; + cache-block-size = <64>; + cache-level = <2>; + cache-size = <1048576>; + cache-sets = <1024>; + cache-unified; + }; + }; + + osc: oscillator {Does u-boot need it?
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
arch/riscv/dts/th1520.dtsi line 139
Quoted 6 lines
arch/riscv/dts/th1520.dtsi new file +6
-0+ compatible = "fixed-clock"; + clock-output-names = "osc_24m"; + #clock-cells = <0>; + }; + + osc_32k: 32k-oscillator {Does u-boot need it?
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
arch/riscv/dts/th1520.dtsi line 145
Quoted 6 lines
arch/riscv/dts/th1520.dtsi new file +6
-0+ compatible = "fixed-clock"; + clock-output-names = "osc_32k"; + #clock-cells = <0>; + }; + + apb_clk: apb-clk-clock {Does u-boot need it?
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
arch/riscv/dts/th1520.dtsi new file +11
-0+ compatible = "fixed-clock"; + clock-output-names = "apb_clk"; + #clock-cells = <0>; + }; + + uart_sclk: uart-sclk-clock { + compatible = "fixed-clock"; + clock-output-names = "uart_sclk"; + #clock-cells = <0>; + }; +Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
arch/riscv/dts/th1520.dtsi line 164
Quoted 8 lines
arch/riscv/dts/th1520.dtsi new file +8
-0+ soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + cpurst: cpurst {The u-boot needn't it
Quoted 75 lines
Quoted 75 lines
Quoted 75 lines
Quoted 75 lines
Quoted 75 lines
Quoted 9 lines
arch/riscv/dts/th1520.dtsi line 171
Quoted 7 lines
arch/riscv/dts/th1520.dtsi new file +7
-0+ compatible = "thead,reset-th1520"; + entry-reg = <0xff 0xff019050>; + entry-cnt = <4>; + control-reg = <0xff 0xff015004>; + control-val = <0x1c>; + csr-copy = <0x7f3 0x7c0 0x7c1 0x7c2 0x7c3 0x7c5 0x7cc>; + };This part has been changed.
noted, will update accordingly
Quoted 64 lines
Quoted 64 lines
arch/riscv/dts/th1520.dtsi new file +64
-0+ + plic: interrupt-controller@ffd8000000 { + compatible = "thead,th1520-plic", "thead,c900-plic"; + reg = <0xff 0xd8000000 0x0 0x01000000>; + interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>, + <&cpu1_intc 11>, <&cpu1_intc 9>, + <&cpu2_intc 11>, <&cpu2_intc 9>, + <&cpu3_intc 11>, <&cpu3_intc 9>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + riscv,ndev = <240>; + }; + + clint: timer@ffdc000000 { + compatible = "thead,th1520-clint", "thead,c900-clint"; + reg = <0xff 0xdc000000 0x0 0x00010000>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>, + <&cpu2_intc 3>, <&cpu2_intc 7>, + <&cpu3_intc 3>, <&cpu3_intc 7>; + }; + + uart0: serial@ffe7014000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7014000 0x0 0x4000>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart1: serial@ffe7f00000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f00000 0x0 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart3: serial@ffe7f04000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xe7f04000 0x0 0x4000>; + interrupts = <39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + gpio2: gpio@ffe7f34000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f34000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portc: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>;Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
arch/riscv/dts/th1520.dtsi line 243
Quoted 8 lines
arch/riscv/dts/th1520.dtsi new file +8
-0+ reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <58 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio3: gpio@ffe7f38000 {Do we enable the gpio driver in u-boot?
Quoted 227 lines
Quoted 219 lines
Quoted 208 lines
Quoted 208 lines
Quoted 205 lines
Quoted 192 lines
Quoted 192 lines
arch/riscv/dts/th1520.dtsi new file +192
-0+ compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xe7f38000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portd: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <59 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio0: gpio@ffec005000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec005000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <56 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio1: gpio@ffec006000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xec006000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portb: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <57 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + uart2: serial@ffec010000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xec010000 0x0 0x4000>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer0: timer@ffefc32000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer1: timer@ffefc32014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer2: timer@ffefc32028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc32028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer3: timer@ffefc3203c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xefc3203c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + uart4: serial@fff7f08000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f08000 0x0 0x4000>; + interrupts = <40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart5: serial@fff7f0c000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff 0xf7f0c000 0x0 0x4000>; + interrupts = <41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart_sclk>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + timer4: timer@ffffc33000 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33000 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer5: timer@ffffc33014 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33014 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer6: timer@ffffc33028 { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc33028 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + timer7: timer@ffffc3303c { + compatible = "snps,dw-apb-timer"; + reg = <0xff 0xffc3303c 0x0 0x14>; + clocks = <&apb_clk>; + clock-names = "timer"; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + ao_gpio0: gpio@fffff41000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff41000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + porte: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <76 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + ao_gpio1: gpio@fffff52000 { + compatible = "snps,dw-apb-gpio"; + reg = <0xff 0xfff52000 0x0 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + portf: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + ngpios = <32>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; +};Quoted 8 lines
Quoted 3 lines
--
2.40.0--
Best Regards
Guo Ren--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55Quoted 8 lines
Quoted 3 lines
--
Best Regards
Guo Ren--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55Quoted 3 lines
--
Best Regards
Guo Ren--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55Signature · 2 lines
Best Regards Guo Ren
Signature · 3 lines
Yixun Lan (dlan) Gentoo Linux Developer GPG Key ID AABEFD55
PATCH RESEND 3/4 configs: th1520_lpi4a_defconfig: Add initial config
In reply to Yixun LanAdd basic config for Sipeed Lichee PI 4A board which make it capable of booting into serial console.
--- configs/th1520_lpi4a_defconfig | 82 ++++++++++++++++++++++++++++++++++ 1 file changed, 82 insertions(+) create mode 100644 configs/th1520_lpi4a_defconfig
configs/th1520_lpi4a_defconfig new file +82 -0
@@ -0,0 +1,82 @@ +CONFIG_RISCV=y +CONFIG_SYS_MALLOC_LEN=0x800000 +CONFIG_SYS_MALLOC_F_LEN=0x3000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000 +CONFIG_DEFAULT_DEVICE_TREE="th1520-lichee-pi-4a" +CONFIG_SYS_PROMPT="LPI4A=> " +CONFIG_SYS_LOAD_ADDR=0x80200000 +# CONFIG_SMP is not set +CONFIG_TARGET_TH1520_LPI4A=y +CONFIG_ARCH_RV64I=y +CONFIG_OF_BOARD_FIXUP=y +CONFIG_SYS_BOOT_GET_CMDLINE=y +CONFIG_SYS_BOOT_GET_KBD=y +CONFIG_FIT=y +# CONFIG_FIT_FULL_CHECK is not set +# CONFIG_FIT_PRINT is not set +# CONFIG_BOOTSTD is not set +# CONFIG_LEGACY_IMAGE_FORMAT is not set +CONFIG_DISTRO_DEFAULTS=y +CONFIG_BOOTARGS_SUBST=y +CONFIG_BOOTCOMMAND="" +CONFIG_DEFAULT_FDT_FILE="thead/th1520-lichee-pi-4a.dtb" +CONFIG_LOG=y +CONFIG_DISPLAY_CPUINFO=y +CONFIG_DISPLAY_BOARDINFO=y +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SYS_CBSIZE=256 +CONFIG_SYS_PBSIZE=276 +CONFIG_CMD_CONFIG=y +CONFIG_CMD_LICENSE=y +CONFIG_CMD_BOOTZ=y +# CONFIG_BOOTM_NETBSD is not set +# CONFIG_BOOTM_PLAN9 is not set +# CONFIG_BOOTM_RTEMS is not set +# CONFIG_BOOTM_VXWORKS is not set +CONFIG_SYS_BOOTM_LEN=0x4000000 +CONFIG_CMD_BOOTMENU=y +# CONFIG_CMD_ELF is not set +# CONFIG_CMD_IMI is not set +# CONFIG_CMD_XIMG is not set +# CONFIG_CMD_EXPORTENV is not set +# CONFIG_CMD_IMPORTENV is not set +# CONFIG_CMD_EDITENV is not set +# CONFIG_CMD_SAVEENV is not set +# CONFIG_CMD_CRC32 is not set +# CONFIG_CMD_MEMORY is not set +# CONFIG_CMD_LZMADEC is not set +# CONFIG_CMD_UNLZ4 is not set +# CONFIG_CMD_UNZIP is not set +# CONFIG_CMD_LOADB is not set +# CONFIG_CMD_LOADS is not set +# CONFIG_CMD_ITEST is not set +# CONFIG_CMD_SOURCE is not set +# CONFIG_CMD_SETEXPR is not set +# CONFIG_CMD_SLEEP is not set +CONFIG_PARTITION_TYPE_GUID=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_VERSION_VARIABLE=y +# CONFIG_NET is not set +# CONFIG_BLOCK_CACHE is not set +# CONFIG_GPIO is not set +# CONFIG_I2C is not set +# CONFIG_INPUT is not set +# CONFIG_DM_MMC is not set +# CONFIG_MTD is not set +# CONFIG_POWER is not set +CONFIG_SYS_NS16550=y +CONFIG_RISCV_TIMER=y +CONFIG_AES=y +CONFIG_BLAKE2=y +CONFIG_SHA512=y +CONFIG_LZ4=y +CONFIG_LZMA=y +CONFIG_LZO=y +CONFIG_ZLIB_UNCOMPRESS=y +CONFIG_BZIP2=y +CONFIG_ZSTD=y +CONFIG_LIB_RATIONAL=y +# CONFIG_EFI_LOADER is not set +# CONFIG_LMB_USE_MAX_REGIONS is not set
Signature · 1 line
2.40.0
PATCH RESEND 4/4 doc: t-head: lpi4a: document Lichee PI 4A board
In reply to Yixun Lan--- doc/board/index.rst | 1 + doc/board/thead/index.rst | 9 +++ doc/board/thead/lpi4a.rst | 112 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 122 insertions(+) create mode 100644 doc/board/thead/index.rst create mode 100644 doc/board/thead/lpi4a.rst
doc/board/index.rst +1 -0
@@ -45,6 +45,7 @@ Board-specific doc starfive/index ste/index tbs/index + thead/index ti/index toradex/index variscite/index
doc/board/thead/index.rst new file +9 -0
@@ -0,0 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +T-HEAD +======== + +.. toctree:: + :maxdepth: 1 + + lpi4a
doc/board/thead/lpi4a.rst new file +112 -0
112 lines not on this page · raw message
Signature · 1 line
2.40.0
Re: [RESEND PATCH v1 4/4] doc: t-head: lpi4a: document Lichee PI 4A board
Hi YiXun,
Quoted 43 lines · Yixun Lan
Reviewed-by Wei Fu <[email protected]>Signed-off-by Yixun Lan <[email protected]>--- doc/board/index.rst | 1 + doc/board/thead/index.rst | 9 +++ doc/board/thead/lpi4a.rst | 112 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 122 insertions(+) create mode 100644 doc/board/thead/index.rst create mode 100644 doc/board/thead/lpi4a.rstdoc/board/index.rst +1
-0@@ -45,6 +45,7 @@ Board-specific doc starfive/index ste/index tbs/index + thead/index ti/index toradex/index variscite/indexdoc/board/thead/index.rst new file +9
-0@@ -0,0 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +T-HEAD +======== + +.. toctree:: + :maxdepth: 1 + + lpi4adoc/board/thead/lpi4a.rst new file +0
-0
doc/board/thead/lpi4a.rst line 5
Quoted 5 lines
doc/board/thead/lpi4a.rst new file +5
-0@@ -0,0 +1,112 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Sipeed's Lichee PI 4A based on T-HEAD TH1520 SoC +==================== +
The underline is too short and would cause error when building docs.
Best regards,
Leo
Quoted 110 lines
doc/board/thead/lpi4a.rst new file +107
-0+TH1520 RISC-V SoC +--------------------- +The TH1520 is 4+2 core 64-bit RISC-V SoC from Alibaba T-HEAD, it's capable of +running highest CPU frequency at 2.5 GHz, integrate Imagination GPU for graphics, +also with 4 TOPS NPU for AI acceleration. + +Mainline support +---------------- + +The support for following drivers are already enabled: + +1. ns16550 UART Driver. + +Building +~~~~~~~~ + +1. Add the RISC-V toolchain to your PATH. +2. Setup ARCH & cross compilation environment variable: + +.. code-block:: none + + export CROSS_COMPILE=<riscv64 toolchain prefix> + +The U-Boot is capable of running in M-Mode, so we can directly build it. + +.. code-block:: console + + cd <U-Boot-dir> + make th1520_lpi4a_defconfig + make + +This will generate u-boot-dtb.bin + +Booting +~~~~~~~ + +Currently, we rely on vendor u-boot to initialize the clock, pinctrl subsystem, +and chain load the mainline u-boot image either via tftp or emmc storage, +then bootup from it. + +Sample boot log from Lichee PI 4A board via tftp +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +.. code-block:: none + + brom_ver 8 + [APP][E] protocol_connect failed, exit. + + U-Boot SPL 2020.01-00016-g8c870a6be8 (May 20 2023 - 01:04:49 +0000) + FM[1] lpddr4x dualrank freq=3733 64bit dbi_off=n sdram init + ddr initialized, jump to uboot + image has no header + + + U-Boot 2020.01-00016-g8c870a6be8 (May 20 2023 - 01:04:49 +0000) + + CPU: rv64imafdcvsu + Model: T-HEAD c910 light + DRAM: 8 GiB + C910 CPU FREQ: 750MHz + AHB2_CPUSYS_HCLK FREQ: 250MHz + AHB3_CPUSYS_PCLK FREQ: 125MHz + PERISYS_AHB_HCLK FREQ: 250MHz + PERISYS_APB_PCLK FREQ: 62MHz + GMAC PLL POSTDIV FREQ: 1000MHZ + DPU0 PLL POSTDIV FREQ: 1188MHZ + DPU1 PLL POSTDIV FREQ: 1188MHZ + MMC: sdhci@ffe7080000: 0, sd@ffe7090000: 1 + Loading Environment from MMC... OK + Error reading output register + Warning: cannot get lcd-en GPIO + LCD panel cannot be found : -121 + splash screen startup cost 16 ms + In: serial + Out: serial + Err: serial + Net: + Warning: ethernet@ffe7070000 using MAC address from ROM + eth0: ethernet@ffe7070000ethernet@ffe7070000:0 is connected to ethernet@ffe7070000. Reconnecting to ethernet@ffe7060000 + + Warning: ethernet@ffe7060000 (eth1) using random MAC address - 42:25:d4:16:5f:fc + , eth1: ethernet@ffe7060000 + Hit any key to stop autoboot: 2 + ethernet@ffe7060000 Waiting for PHY auto negotiation to complete.. done + Speed: 1000, full duplex + Using ethernet@ffe7070000 device + TFTP from server 192.168.8.50; our IP address is 192.168.8.45 + Filename 'u-boot-dtb.bin'. + Load address: 0x1c00000 + Loading: * ######################### + 8 MiB/s + done + Bytes transferred = 376686 (5bf6e hex) + ## Starting application at 0x01C00000 ... + + U-Boot 2023.07-rc2-00004-g1befbe31c1 (May 23 2023 - 18:40:01 +0800) + + CPU: rv64imafdc + Model: Sipeed Lichee Pi 4A + DRAM: 8 GiB + Core: 13 devices, 6 uclasses, devicetree: separate + Loading Environment from <NULL>... OK + In: serial@ffe7014000 + Out: serial@ffe7014000 + Err: serial@ffe7014000 + Model: Sipeed Lichee Pi 4A + LPI4A=>Signature · 1 line
2.40.0