Skip to contentSkip to conversation

clk: qcom: clk-rcg2: introduce support for multiple conf for same freq

PATCH Superseded Christian Marangi 2 participants 5 messages May 31, 2023 – Jul 13, 2023

Subsystems (3)

v5 of 8 Superseded Latest is v8 →

lore
Share & tools
lore
#0 lore raw

v5 cover clk: qcom: clk-rcg2: introduce support for multiple conf for same freq

This small series fix a current problem with ipq8074 where the 2 uniphy port doesn't work in some corner case with some clk configuration. The port to correctly work require a specific frequency, using the wrong one results in the port not transmitting data.

With the current code with a requested freq of 125MHz, the frequency is set to 105MHz. This is caused by the fact that there are 2 different configuration to set 125MHz and it's always selected the first one that results in 105MHz.

In the original QSDK code, the frequency configuration selection is different and the CEIL FLOOR logic is not present. Instead it's used a BEST approach where the frequency table is checked and then it's checked if there are duplicate entry.

This proposed implementation is more specific and introduce an entire new set of ops and a specific freq table to support this special configuration.

A union is introduced in rcg2 struct to not duplicate the struct. A new set of ops clk_rcg2_fm_ops are introduced to support this new kind of frequency table.

Changes v5:
- Rework selection logic with suggestion from Konrad
- Return -EINVAL and WARN if we fail to find a correct conf Changes v4:
- Drop suggested but wrong re-search patch
- Move everything to separate ops and struct to not affect current rcg2 users.
Changes v3:
- Add qcom_find_freq_exact
- Drop re-search on rcg2_set_rate
- Rework multiple conf patch to follow new implementation Changes v2:
- Out of RFC
- Fix compile warning from buildbot related to F redefinition

Christian Marangi (3):
clk: qcom: clk-rcg: introduce support for multiple conf for same freq
clk: qcom: clk-rcg2: add support for rcg2 freq multi ops
clk: qcom: gcc-ipq8074: rework nss_port5/6 clock to multiple conf

 drivers/clk/qcom/clk-rcg.h     |  24 ++++-
 drivers/clk/qcom/clk-rcg2.c    | 163 +++++++++++++++++++++++++++++++++
 drivers/clk/qcom/common.c      |  18 ++++
 drivers/clk/qcom/common.h      |   2 +
 drivers/clk/qcom/gcc-ipq8074.c | 120 +++++++++++++++---------
 5 files changed, 282 insertions(+), 45 deletions(-)
Signature · 1 line
2.39.2
#1 lore raw

PATCH v5 1/3 clk: qcom: clk-rcg: introduce support for multiple conf for same freq

Some RCG frequency can be reached by multiple configuration.

We currently declare multiple configuration for the same frequency but that is not supported and always the first configuration will be taken.

These multiple configuration are needed as based on the current parent configuration, it may be needed to use a different configuration to reach the same frequency.

To handle this introduce 3 new macro, C, FM and FMS:

- C is used to declare a freq_conf where src, pre_div, m and n are provided.

- FM is used to declare a freq_multi_tbl with the frequency and an array of confs to insert all the config for the provided frequency.

- FMS is used to declare a freq_multi_tbl with the frequency and an array of a single conf with the provided src, pre_div, m and n.

Struct clk_rcg2 is changed to add a union type to reference a simple freq_tbl or a complex freq_multi_tbl.

---
 drivers/clk/qcom/clk-rcg.h | 23 ++++++++++++++++++++++-
 1 file changed, 22 insertions(+), 1 deletion(-)
drivers/clk/qcom/clk-rcg.h +22 -1
index 01581f4d2c39..dc85b46b0d79 100644
@@ -17,6 +17,23 @@ struct freq_tbl {
 	u16 n;
 };
 
+#define C(s, h, m, n) { (s), (2 * (h) - 1), (m), (n) }
+#define FM(f, confs) { (f), ARRAY_SIZE(confs), (confs) }
+#define FMS(f, s, h, m, n) { (f), 1, (const struct freq_conf []){ C(s, h, m, n) } }
+
+struct freq_conf {
+	u8 src;
+	u8 pre_div;
+	u16 m;
+	u16 n;
+};
+
+struct freq_multi_tbl {
+	unsigned long freq;
+	int num_confs;
+	const struct freq_conf *confs;
+};
+
 /**
  * struct mn - M/N:D counter
  * @mnctr_en_bit: bit to enable mn counter
@@ -138,6 +155,7 @@ extern const struct clk_ops clk_dyn_rcg_ops;
  * @safe_src_index: safe src index value
  * @parent_map: map from software's parent index to hardware's src_sel field
  * @freq_tbl: frequency table
+ * @freq_multi_tbl: frequency table for clocks reachable with multiple RCGs conf
  * @clkr: regmap clock handle
  * @cfg_off: defines the cfg register offset from the CMD_RCGR + CFG_REG
  * @parked_cfg: cached value of the CFG register for parked RCGs
@@ -148,7 +166,10 @@ struct clk_rcg2 {
 	u8			hid_width;
 	u8			safe_src_index;
 	const struct parent_map	*parent_map;
-	const struct freq_tbl	*freq_tbl;
+	union {
+		const struct freq_tbl		*freq_tbl;
+		const struct freq_multi_tbl	*freq_multi_tbl;
+	};
 	struct clk_regmap	clkr;
 	u8			cfg_off;
 	u32			parked_cfg;
Signature · 1 line
2.39.2
#2 lore raw

PATCH v5 2/3 clk: qcom: clk-rcg2: add support for rcg2 freq multi ops

In reply to Christian Marangi

Some RCG frequency can be reached by multiple configuration.

Add clk_rcg2_fm_ops ops to support these special RCG configurations.

These alternative ops will select the frequency using a CEIL policy.

When the correct frequency is found, the correct config is selected by calculating the final rate (by checking the defined parent and values in the config that is being checked) and deciding based on the one that is less different than the requested one.

These check are skipped if there is just on config for the requested freq.

qcom_find_freq_multi is added to search the freq with the new struct freq_multi_tbl.
__clk_rcg2_select_conf is used to select the correct conf by simulating the final clock.
If a conf can't be found due to parent not reachable, a WARN is printed and -EINVAL is returned.

---
 drivers/clk/qcom/clk-rcg.h  |   1 +
 drivers/clk/qcom/clk-rcg2.c | 163 ++++++++++++++++++++++++++++++++++++
 drivers/clk/qcom/common.c   |  18 ++++
 drivers/clk/qcom/common.h   |   2 +
 4 files changed, 184 insertions(+)
drivers/clk/qcom/clk-rcg.h +1 -0
index dc85b46b0d79..f8ec989ed3d9 100644
@@ -188,6 +188,7 @@ struct clk_rcg2_gfx3d {
 
 extern const struct clk_ops clk_rcg2_ops;
 extern const struct clk_ops clk_rcg2_floor_ops;
+extern const struct clk_ops clk_rcg2_fm_ops;
 extern const struct clk_ops clk_rcg2_mux_closest_ops;
 extern const struct clk_ops clk_edp_pixel_ops;
 extern const struct clk_ops clk_byte_ops;
drivers/clk/qcom/clk-rcg2.c +163 -0

199 lines not on this page · raw message

drivers/clk/qcom/common.c +18 -0
index 75f09e6e057e..48f81e3a5e80 100644
@@ -41,6 +41,24 @@ struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, unsigned long rate)
 }
 EXPORT_SYMBOL_GPL(qcom_find_freq);
 
+const struct freq_multi_tbl *qcom_find_freq_multi(const struct freq_multi_tbl *f,
+						  unsigned long rate)
+{
+	if (!f)
+		return NULL;
+
+	if (!f->freq)
+		return f;
+
+	for (; f->freq; f++)
+		if (rate <= f->freq)
+			return f;
+
+	/* Default to our fastest rate */
+	return f - 1;
+}
+EXPORT_SYMBOL_GPL(qcom_find_freq_multi);
+
 const struct freq_tbl *qcom_find_freq_floor(const struct freq_tbl *f,
 					    unsigned long rate)
 {
drivers/clk/qcom/common.h +2 -0
index 9c8f7b798d9f..2d4a8a837e6c 100644
@@ -45,6 +45,8 @@ extern const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f,
 					     unsigned long rate);
 extern const struct freq_tbl *qcom_find_freq_floor(const struct freq_tbl *f,
 						   unsigned long rate);
+extern const struct freq_multi_tbl *qcom_find_freq_multi(const struct freq_multi_tbl *f,
+							 unsigned long rate);
 extern void
 qcom_pll_set_fsm_mode(struct regmap *m, u32 reg, u8 bias_count, u8 lock_count);
 extern int qcom_find_src_index(struct clk_hw *hw, const struct parent_map *map,
Signature · 1 line
2.39.2
#3 lore raw

Re: [PATCH v5 2/3] clk: qcom: clk-rcg2: add support for rcg2 freq multi ops

Quoted 22 lines · Christian Marangi

Some RCG frequency can be reached by multiple configuration.

Add clk_rcg2_fm_ops ops to support these special RCG configurations.

These alternative ops will select the frequency using a CEIL policy.

When the correct frequency is found, the correct config is selected by calculating the final rate (by checking the defined parent and values in the config that is being checked) and deciding based on the one that is less different than the requested one.

These check are skipped if there is just on config for the requested freq.

qcom_find_freq_multi is added to search the freq with the new struct freq_multi_tbl.
__clk_rcg2_select_conf is used to select the correct conf by simulating the final clock.
If a conf can't be found due to parent not reachable, a WARN is printed and -EINVAL is returned.

...

Quoted 50 lines
drivers/clk/qcom/clk-rcg2.c +42 -0
index 76551534f10d..9a139fc8bbfa 100644
@@ -266,6 +266,112 @@ static int _freq_tbl_determine_rate(struct clk_hw *hw, const struct freq_tbl *f,
 	return 0;
 }
 
+static const struct freq_conf *
+__clk_rcg2_select_conf(struct clk_hw *hw, const struct freq_multi_tbl *f,
+		       unsigned long req_rate)
+{
+	unsigned long rate_diff, best_rate_diff = ULONG_MAX;
+	const struct freq_conf *conf, *best_conf;
+	struct clk_rcg2 *rcg = to_clk_rcg2(hw);
+	const char *name = clk_hw_get_name(hw);
+	unsigned long parent_rate, rate;
+	struct clk_hw *p;
+	int index, i;
+
+	/* Exit early if only one config is defined */
+	if (f->num_confs == 1)
+		return f->confs;
+
+	/* Search in each provided config the one that is near the wanted rate */
+	for (i = 0, conf = f->confs; i < f->num_confs; i++, conf++) {
+		index = qcom_find_src_index(hw, rcg->parent_map, conf->src);
+		if (index < 0)
+			continue;
+
+		p = clk_hw_get_parent_by_index(hw, index);
+		if (!p)
+			continue;
+
+		parent_rate =  clk_hw_get_rate(p);
+		rate = calc_rate(parent_rate, conf->n, conf->m, conf->n, conf->pre_div);
+
+		if (rate == req_rate) {
+			best_conf = conf;
+			break;
+		}
+
+		rate_diff = abs(req_rate - rate);
+		if (rate_diff < best_rate_diff) {
+			best_rate_diff = rate_diff;
+			best_conf = conf;
+		}
+	}
+
+	/*

drivers/clk/qcom/clk-rcg2.c static int _freq_tbl_determine_rate(struct clk_hw *hw, const struct freq_tbl *f, · line 320

Quoted 10 lines
drivers/clk/qcom/clk-rcg2.c +10 -0
+	 * Very unlikely. Warn if we couldn't find a correct config
+	 * due to parent not present.
+	 */
+	if (unlikely(i == f->num_confs)) {
+		WARN(1, "%s: can't find a configuration for rate %lu.",
+		     name, req_rate);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return best_conf;

Hi Christian,

It's unclear to me if this can actually occur, but Sparse warns that best_conf may be uninitialised here.

Quoted 1 line
drivers/clk/qcom/clk-rcg2.c +1 -0
+}

...

#4 lore raw

PATCH v5 3/3 clk: qcom: gcc-ipq8074: rework nss_port5/6 clock to multiple conf

In reply to Christian Marangi

Rework nss_port5/6 to use the new multiple configuration implementation and correctly fix the clocks for these port under some corner case.

This is particularly relevant for device that have 2.5G or 10G port connected to port5 or port 6 on ipq8074. As the parent are shared across multiple port it may be required to select the correct configuration to accomplish the desired clock. Without this patch such port doesn't work in some specific ethernet speed as the clock will be set to the wrong frequency as we just select the first configuration for the related frequency instead of selecting the best one.

---
 drivers/clk/qcom/gcc-ipq8074.c | 120 +++++++++++++++++++++------------
 1 file changed, 76 insertions(+), 44 deletions(-)
drivers/clk/qcom/gcc-ipq8074.c +76 -44
index 6541d98c0348..bce459cecb2d 100644
@@ -1682,15 +1682,23 @@ static struct clk_regmap_div nss_port4_tx_div_clk_src = {
 	},
 };
 
-static const struct freq_tbl ftbl_nss_port5_rx_clk_src[] = {
-	F(19200000, P_XO, 1, 0, 0),
-	F(25000000, P_UNIPHY1_RX, 12.5, 0, 0),
-	F(25000000, P_UNIPHY0_RX, 5, 0, 0),
-	F(78125000, P_UNIPHY1_RX, 4, 0, 0),
-	F(125000000, P_UNIPHY1_RX, 2.5, 0, 0),
-	F(125000000, P_UNIPHY0_RX, 1, 0, 0),
-	F(156250000, P_UNIPHY1_RX, 2, 0, 0),
-	F(312500000, P_UNIPHY1_RX, 1, 0, 0),
+static const struct freq_conf ftbl_nss_port5_rx_clk_src_25[] = {
+	C(P_UNIPHY1_RX, 12.5, 0, 0),
+	C(P_UNIPHY0_RX, 5, 0, 0),
+};
+
+static const struct freq_conf ftbl_nss_port5_rx_clk_src_125[] = {
+	C(P_UNIPHY1_RX, 2.5, 0, 0),
+	C(P_UNIPHY0_RX, 1, 0, 0),
+};
+
+static const struct freq_multi_tbl ftbl_nss_port5_rx_clk_src[] = {
+	FMS(19200000, P_XO, 1, 0, 0),
+	FM(25000000, ftbl_nss_port5_rx_clk_src_25),
+	FMS(78125000, P_UNIPHY1_RX, 4, 0, 0),
+	FM(125000000, ftbl_nss_port5_rx_clk_src_125),
+	FMS(156250000, P_UNIPHY1_RX, 2, 0, 0),
+	FMS(312500000, P_UNIPHY1_RX, 1, 0, 0),
 	{ }
 };
 
@@ -1717,14 +1725,14 @@ gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias_map[] = {
 
 static struct clk_rcg2 nss_port5_rx_clk_src = {
 	.cmd_rcgr = 0x68060,
-	.freq_tbl = ftbl_nss_port5_rx_clk_src,
+	.freq_multi_tbl = ftbl_nss_port5_rx_clk_src,
 	.hid_width = 5,
 	.parent_map = gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias_map,
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "nss_port5_rx_clk_src",
 		.parent_data = gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias,
 		.num_parents = ARRAY_SIZE(gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias),
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_fm_ops,
 	},
 };
 
@@ -1744,15 +1752,23 @@ static struct clk_regmap_div nss_port5_rx_div_clk_src = {
 	},
 };
 
-static const struct freq_tbl ftbl_nss_port5_tx_clk_src[] = {
-	F(19200000, P_XO, 1, 0, 0),
-	F(25000000, P_UNIPHY1_TX, 12.5, 0, 0),
-	F(25000000, P_UNIPHY0_TX, 5, 0, 0),
-	F(78125000, P_UNIPHY1_TX, 4, 0, 0),
-	F(125000000, P_UNIPHY1_TX, 2.5, 0, 0),
-	F(125000000, P_UNIPHY0_TX, 1, 0, 0),
-	F(156250000, P_UNIPHY1_TX, 2, 0, 0),
-	F(312500000, P_UNIPHY1_TX, 1, 0, 0),
+static const struct freq_conf ftbl_nss_port5_tx_clk_src_25[] = {
+	C(P_UNIPHY1_TX, 12.5, 0, 0),
+	C(P_UNIPHY0_TX, 5, 0, 0),
+};
+
+static const struct freq_conf ftbl_nss_port5_tx_clk_src_125[] = {
+	C(P_UNIPHY1_TX, 2.5, 0, 0),
+	C(P_UNIPHY0_TX, 1, 0, 0),
+};
+
+static const struct freq_multi_tbl ftbl_nss_port5_tx_clk_src[] = {
+	FMS(19200000, P_XO, 1, 0, 0),
+	FM(25000000, ftbl_nss_port5_tx_clk_src_25),
+	FMS(78125000, P_UNIPHY1_TX, 4, 0, 0),
+	FM(125000000, ftbl_nss_port5_tx_clk_src_125),
+	FMS(156250000, P_UNIPHY1_TX, 2, 0, 0),
+	FMS(312500000, P_UNIPHY1_TX, 1, 0, 0),
 	{ }
 };
 
@@ -1779,14 +1795,14 @@ gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias_map[] = {
 
 static struct clk_rcg2 nss_port5_tx_clk_src = {
 	.cmd_rcgr = 0x68068,
-	.freq_tbl = ftbl_nss_port5_tx_clk_src,
+	.freq_multi_tbl = ftbl_nss_port5_tx_clk_src,
 	.hid_width = 5,
 	.parent_map = gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias_map,
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "nss_port5_tx_clk_src",
 		.parent_data = gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias,
 		.num_parents = ARRAY_SIZE(gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias),
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_fm_ops,
 	},
 };
 
@@ -1806,15 +1822,23 @@ static struct clk_regmap_div nss_port5_tx_div_clk_src = {
 	},
 };
 
-static const struct freq_tbl ftbl_nss_port6_rx_clk_src[] = {
-	F(19200000, P_XO, 1, 0, 0),
-	F(25000000, P_UNIPHY2_RX, 5, 0, 0),
-	F(25000000, P_UNIPHY2_RX, 12.5, 0, 0),
-	F(78125000, P_UNIPHY2_RX, 4, 0, 0),
-	F(125000000, P_UNIPHY2_RX, 1, 0, 0),
-	F(125000000, P_UNIPHY2_RX, 2.5, 0, 0),
-	F(156250000, P_UNIPHY2_RX, 2, 0, 0),
-	F(312500000, P_UNIPHY2_RX, 1, 0, 0),
+static const struct freq_conf ftbl_nss_port6_rx_clk_src_25[] = {
+	C(P_UNIPHY2_RX, 5, 0, 0),
+	C(P_UNIPHY2_RX, 12.5, 0, 0),
+};
+
+static const struct freq_conf ftbl_nss_port6_rx_clk_src_125[] = {
+	C(P_UNIPHY2_RX, 1, 0, 0),
+	C(P_UNIPHY2_RX, 2.5, 0, 0),
+};
+
+static const struct freq_multi_tbl ftbl_nss_port6_rx_clk_src[] = {
+	FMS(19200000, P_XO, 1, 0, 0),
+	FM(25000000, ftbl_nss_port6_rx_clk_src_25),
+	FMS(78125000, P_UNIPHY2_RX, 4, 0, 0),
+	FM(125000000, ftbl_nss_port6_rx_clk_src_125),
+	FMS(156250000, P_UNIPHY2_RX, 2, 0, 0),
+	FMS(312500000, P_UNIPHY2_RX, 1, 0, 0),
 	{ }
 };
 
@@ -1836,14 +1860,14 @@ static const struct parent_map gcc_xo_uniphy2_rx_tx_ubi32_bias_map[] = {
 
 static struct clk_rcg2 nss_port6_rx_clk_src = {
 	.cmd_rcgr = 0x68070,
-	.freq_tbl = ftbl_nss_port6_rx_clk_src,
+	.freq_multi_tbl = ftbl_nss_port6_rx_clk_src,
 	.hid_width = 5,
 	.parent_map = gcc_xo_uniphy2_rx_tx_ubi32_bias_map,
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "nss_port6_rx_clk_src",
 		.parent_data = gcc_xo_uniphy2_rx_tx_ubi32_bias,
 		.num_parents = ARRAY_SIZE(gcc_xo_uniphy2_rx_tx_ubi32_bias),
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_fm_ops,
 	},
 };
 
@@ -1863,15 +1887,23 @@ static struct clk_regmap_div nss_port6_rx_div_clk_src = {
 	},
 };
 
-static const struct freq_tbl ftbl_nss_port6_tx_clk_src[] = {
-	F(19200000, P_XO, 1, 0, 0),
-	F(25000000, P_UNIPHY2_TX, 5, 0, 0),
-	F(25000000, P_UNIPHY2_TX, 12.5, 0, 0),
-	F(78125000, P_UNIPHY2_TX, 4, 0, 0),
-	F(125000000, P_UNIPHY2_TX, 1, 0, 0),
-	F(125000000, P_UNIPHY2_TX, 2.5, 0, 0),
-	F(156250000, P_UNIPHY2_TX, 2, 0, 0),
-	F(312500000, P_UNIPHY2_TX, 1, 0, 0),
+static const struct freq_conf ftbl_nss_port6_tx_clk_src_25[] = {
+	C(P_UNIPHY2_TX, 5, 0, 0),
+	C(P_UNIPHY2_TX, 12.5, 0, 0),
+};
+
+static const struct freq_conf ftbl_nss_port6_tx_clk_src_125[] = {
+	C(P_UNIPHY2_TX, 1, 0, 0),
+	C(P_UNIPHY2_TX, 2.5, 0, 0),
+};
+
+static const struct freq_multi_tbl ftbl_nss_port6_tx_clk_src[] = {
+	FMS(19200000, P_XO, 1, 0, 0),
+	FM(25000000, ftbl_nss_port6_tx_clk_src_25),
+	FMS(78125000, P_UNIPHY1_RX, 4, 0, 0),
+	FM(125000000, ftbl_nss_port6_tx_clk_src_125),
+	FMS(156250000, P_UNIPHY1_RX, 2, 0, 0),
+	FMS(312500000, P_UNIPHY1_RX, 1, 0, 0),
 	{ }
 };
 
@@ -1893,14 +1925,14 @@ static const struct parent_map gcc_xo_uniphy2_tx_rx_ubi32_bias_map[] = {
 
 static struct clk_rcg2 nss_port6_tx_clk_src = {
 	.cmd_rcgr = 0x68078,
-	.freq_tbl = ftbl_nss_port6_tx_clk_src,
+	.freq_multi_tbl = ftbl_nss_port6_tx_clk_src,
 	.hid_width = 5,
 	.parent_map = gcc_xo_uniphy2_tx_rx_ubi32_bias_map,
 	.clkr.hw.init = &(struct clk_init_data){
 		.name = "nss_port6_tx_clk_src",
 		.parent_data = gcc_xo_uniphy2_tx_rx_ubi32_bias,
 		.num_parents = ARRAY_SIZE(gcc_xo_uniphy2_tx_rx_ubi32_bias),
-		.ops = &clk_rcg2_ops,
+		.ops = &clk_rcg2_fm_ops,
 	},
 };
 
Signature · 1 line
2.39.2