hw/acpi: Fix PM control register access
PATCH 1/1 hw/acpi: Fix PM control register access
On pegasos2 which has ACPI as part of VT8231 south bridge the board firmware writes PM control register by accessing the second byte so addr will be 1. This wasn't handled correctly and the write went to addr 0 instead. This fixes ACPI shutdown with pegasos2 firmware.
---
This is replacing the previous attempt which changed enduanness to NATIVE_ENDIAN that was found to be wrong. I'm still not sure what's happening as these functions are called with addr = 1 and size = 2 but maybe the guest really does word access to addr 1 when wanting to write 1 byte. This fixes the problem and should not break anything else but please review.
hw/acpi/core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
hw/acpi/core.c +2 -2
@@ -593,13 +593,13 @@ void acpi_pm1_cnt_update(ACPIREGS *ar,static uint64_t acpi_pm_cnt_read (void *opaque,hwaddr addr,unsigned width) {ACPIREGS *ar = opaque; -return ar->pm1.cnt.cnt; +return ar->pm1.cnt.cnt >> addr *8 ; }static void acpi_pm_cnt_write (void *opaque,hwaddr addr,uint64_t val,unsigned width) { -acpi_pm1_cnt_write (opaque, val); +acpi_pm1_cnt_write (opaque, val << addr *8 ); }static const MemoryRegionOps acpi_pm_cnt_ops = {
Signature · 1 line
2.30.9
Quoted 5 lines · BALATON Zoltan
On pegasos2 which has ACPI as part of VT8231 south bridge the board firmware writes PM control register by accessing the second byte so addr will be 1. This wasn't handled correctly and the write went to addr 0 instead. This fixes ACPI shutdown with pegasos2 firmware.
Quoted 8 lines
Signed-off-by BALATON Zoltan <[email protected]>---
This is replacing the previous attempt which changed enduanness toNATIVE_ENDIANthat was found to be wrong. I'm still not sure what's happening as these functions are called with addr = 1 and size = 2 but maybe the guest really does word access to addr 1 when wanting to write 1 byte. This fixes the problem and should not break anything else but please review.
Ping?
Regards,
BALATON Zoltan
Quoted 24 lines
hw/acpi/core.c| 4 ++--1 file changed, 2 insertions(+), 2 deletions(-)hw/acpi/core.c +2
-2@@ -593,13 +593,13 @@ void acpi_pm1_cnt_update(ACPIREGS *ar,static uint64_t acpi_pm_cnt_read (void *opaque,hwaddr addr,unsigned width) {ACPIREGS *ar = opaque; -return ar->pm1.cnt.cnt; +return ar->pm1.cnt.cnt >> addr *8 ; }static void acpi_pm_cnt_write (void *opaque,hwaddr addr,uint64_t val,unsigned width) { -acpi_pm1_cnt_write (opaque, val); +acpi_pm1_cnt_write (opaque, val << addr *8 ); }static const MemoryRegionOps acpi_pm_cnt_ops = {
Quoted 22 lines · On Sun, 28 May 2023 15:57:50 +0200 (CEST) BALATON Zoltan <[email protected]>…
On pegasos2 which has ACPI as part of VT8231 south bridge the board firmware writes PM control register by accessing the second byte so addr will be 1. This wasn't handled correctly and the write went to addr 0 instead. This fixes ACPI shutdown with pegasos2 firmware.
Signed-off-by BALATON Zoltan <[email protected]>---
This is replacing the previous attempt which changed enduanness toNATIVE_ENDIANthat was found to be wrong. I'm still not sure what's happening as these functions are called with addr = 1 and size = 2 but maybe the guest really does word access to addr 1 when wanting to write 1 byte. This fixes the problem and should not break anything else but please review.hw/acpi/core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)hw/acpi/core.c +0
-0
hw/acpi/core.c void acpi_pm1_cnt_update(ACPIREGS *ar, · line 597
Quoted 6 lines
hw/acpi/core.c +1
-1@@ -593,13 +593,13 @@ void acpi_pm1_cnt_update(ACPIREGS *ar,static uint64_t acpi_pm_cnt_read (void *opaque,hwaddr addr,unsigned width) {ACPIREGS *ar = opaque; -return ar->pm1.cnt.cnt; +return ar->pm1.cnt.cnt >> addr *8 ; }
that looks fine
hw/acpi/core.c void acpi_pm1_cnt_update(ACPIREGS *ar, · line 603
Quoted 7 lines
hw/acpi/core.c +1
-1static void acpi_pm_cnt_write (void *opaque,hwaddr addr,uint64_t val,unsigned width) { -acpi_pm1_cnt_write (opaque, val); +acpi_pm1_cnt_write (opaque, val << addr *8 ); }
however, if this is 1 byte write at offset 1,
wouldn't this wipe out lower byte
(aka:
#define ACPI_BITMASK_SCI_ENABLE 0x0001 #define ACPI_BITMASK_BUS_MASTER_RLD 0x0002 #define ACPI_BITMASK_GLOBAL_LOCK_RELEASE 0x0004
)?
Quoted 2 lines
hw/acpi/core.c +0
-0static const MemoryRegionOps acpi_pm_cnt_ops = {
Quoted 40 lines · Igor Mammedov
Quoted 22 lines · On Sun, 28 May 2023 15:57:50 +0200 (CEST) BALATON Zoltan <[email protected]>…
On pegasos2 which has ACPI as part of VT8231 south bridge the board firmware writes PM control register by accessing the second byte so addr will be 1. This wasn't handled correctly and the write went to addr 0 instead. This fixes ACPI shutdown with pegasos2 firmware.
Signed-off-by BALATON Zoltan <[email protected]>---
This is replacing the previous attempt which changed enduanness toNATIVE_ENDIANthat was found to be wrong. I'm still not sure what's happening as these functions are called with addr = 1 and size = 2 but maybe the guest really does word access to addr 1 when wanting to write 1 byte. This fixes the problem and should not break anything else but please review.hw/acpi/core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)hw/acpi/core.c +0
-0hw/acpi/core.c void acpi_pm1_cnt_update(ACPIREGS *ar, · line 597
Quoted 6 lines
hw/acpi/core.c +1
-1@@ -593,13 +593,13 @@ void acpi_pm1_cnt_update(ACPIREGS *ar,static uint64_t acpi_pm_cnt_read (void *opaque,hwaddr addr,unsigned width) {ACPIREGS *ar = opaque; -return ar->pm1.cnt.cnt; +return ar->pm1.cnt.cnt >> addr *8 ; }that looks fine
hw/acpi/core.c void acpi_pm1_cnt_update(ACPIREGS *ar, · line 603
Quoted 7 lines
hw/acpi/core.c +1
-1static void acpi_pm_cnt_write (void *opaque,hwaddr addr,uint64_t val,unsigned width) { -acpi_pm1_cnt_write (opaque, val); +acpi_pm1_cnt_write (opaque, val << addr *8 ); }
Quoted 7 lines
however, if this is 1 byte write at offset 1,
wouldn't this wipe out lower byte
(aka:#define ACPI_BITMASK_SCI_ENABLE 0x0001 #define ACPI_BITMASK_BUS_MASTER_RLD 0x0002 #define ACPI_BITMASK_GLOBAL_LOCK_RELEASE 0x0004)?
Since this will either reset or power off the machine it probably does not really matter. But to fix that more we'd need to rewrite acpi_pm1_cnt_write() to replace acpi_pm_cnt_write() and handle that internally. Or is there another way to handle this? Does that worth the effort when the only known usage is in pegasos2 firmware when it calls power off?
Regards,
BALATON Zoltan
Quoted 49 lines · On Tue, 6 Jun 2023 18:59:48 +0200 (CEST) BALATON Zoltan <[email protected]>…
Quoted 40 lines · Igor Mammedov
Quoted 22 lines · On Sun, 28 May 2023 15:57:50 +0200 (CEST) BALATON Zoltan <[email protected]>…
On pegasos2 which has ACPI as part of VT8231 south bridge the board firmware writes PM control register by accessing the second byte so addr will be 1. This wasn't handled correctly and the write went to addr 0 instead. This fixes ACPI shutdown with pegasos2 firmware.
Signed-off-by BALATON Zoltan <[email protected]>---
This is replacing the previous attempt which changed enduanness toNATIVE_ENDIANthat was found to be wrong. I'm still not sure what's happening as these functions are called with addr = 1 and size = 2 but maybe the guest really does word access to addr 1 when wanting to write 1 byte. This fixes the problem and should not break anything else but please review.hw/acpi/core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)hw/acpi/core.c +0
-0hw/acpi/core.c void acpi_pm1_cnt_update(ACPIREGS *ar, · line 597
Quoted 6 lines
hw/acpi/core.c +1
-1@@ -593,13 +593,13 @@ void acpi_pm1_cnt_update(ACPIREGS *ar,static uint64_t acpi_pm_cnt_read (void *opaque,hwaddr addr,unsigned width) {ACPIREGS *ar = opaque; -return ar->pm1.cnt.cnt; +return ar->pm1.cnt.cnt >> addr *8 ; }that looks fine
hw/acpi/core.c void acpi_pm1_cnt_update(ACPIREGS *ar, · line 603
Quoted 7 lines
hw/acpi/core.c +1
-1static void acpi_pm_cnt_write (void *opaque,hwaddr addr,uint64_t val,unsigned width) { -acpi_pm1_cnt_write (opaque, val); +acpi_pm1_cnt_write (opaque, val << addr *8 ); }Quoted 7 lines
however, if this is 1 byte write at offset 1,
wouldn't this wipe out lower byte
(aka:#define ACPI_BITMASK_SCI_ENABLE 0x0001 #define ACPI_BITMASK_BUS_MASTER_RLD 0x0002 #define ACPI_BITMASK_GLOBAL_LOCK_RELEASE 0x0004)?
Quoted 6 lines
Since this will either reset or power off the machine it probably does not really matter. But to fix that more we'd need to rewrite
acpi_pm1_cnt_write()to replaceacpi_pm_cnt_write()and handle that internally. Or is there another way to handle this? Does that worth the effort when the only known usage is in pegasos2 firmware when it calls power off?
it maybe true for pegasos2 firmware, but this code is shared between several chipsets, so I'd rather do it correctly now, instead of tying to figure out where S3 got broken later (potentially we can go into sleep without reset).
maybe split acpi_pm1_cnt_write() into 2 functions
acpi_pm1_cnt_write(hi, lo) - updates register contents, or move contents to caller and drop function
and then
if (ar->pm1.cnt.cnt & ACPI_BITMASK_SLEEP_ENABLE) {
acpi_pm1_cnt_handle_pm_req(ar->pm1.cnt.cnt)}
Quoted 3 lines
Regards,
BALATON Zoltan