arm64: dts: ti: k3-j7200: Add properties and sync with uboot
Subsystems (2)
v4 cover arm64: dts: ti: k3-j7200: Add properties and sync with uboot
In continuation of patch series posted by Nishanth for sync of uboot device tree with kernel device tree for AM64 SOC.
https://lore.kernel.org/linux-arm-kernel/[email protected]/
This series extend device tree sync/clean up for J7200 SOC.
This patch series build on top of
https://lore.kernel.org/all/[email protected]
Boot logs
https://gist.github.com/uditkumarti/a43decc11c49d59c658cfc4f3f255c5e
Changes since v3:
https://lore.kernel.org/all/[email protected]/
* Add general purpose timers
Added reviewed by Tony Lindgren
* Configure pinctrl for timer IO pads
No change
* remove duplicate main_i2c0 pin mux
Moved before uart pin mux
* Add uart pinmux
Added missing uart pin mux
* Define aliases at board level
* Drop SoC level aliases
Moved aliases<F4> at board level
Changes since v2:
https://lore.kernel.org/all/[email protected]/
* Configure pinctrl for timer IO pads
Added reviewed by Tony Lindgren
* Add uart pin mux in main_pmx0
Changed subject of patch
Changes since v1:
https://lore.kernel.org/all/[email protected]/
* Add general purpose timers:
Addded CLKSEL_VD clock for odd numbered timers
Marked MCU_Timer as reserved, fixed clock index for main_timer13
*Configure pinctrl for timer IO pads
Marked mcu_timerio_input as reserved
*main_pmx0 clean up
Splitted into two patches, One for UART and second for i2c duplication removal
*Add uart pin mux in wkup_pmx0
No change
*Add bootph-pre-ram for u-boot
patch dropped, later will add bootph-pre-ram property later for all nodes.
Udit Kumar (6):
arm64: dts: ti: k3-j7200: Add general purpose timers
arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads
arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0
pin mux
arm64: dts: ti: k3-j7200-common-proc-board: Add uart pinmux
arm64: dts: ti: k3-j7200-common-proc-board: Define aliases at board
level
arm64: dts: ti: k3-j7200: Drop SoC level aliases
.../dts/ti/k3-j7200-common-proc-board.dts | 67 ++++- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 258 ++++++++++++++++++ .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 150 ++++++++++ arch/arm64/boot/dts/ti/k3-j7200.dtsi | 17 -- 4 files changed, 471 insertions(+), 21 deletions(-)
Signature · 1 line
2.34.1
PATCH v4 1/6 arm64: dts: ti: k3-j7200: Add general purpose timers
There are 20 general purpose timers on j721e that can be used for things like PWM using pwm-omap-dmtimer driver. There are also additional ten timers in the MCU domain which are meant for MCU firmware usage and hence marked reserved by default.
The odd numbered timers have the option of being cascaded to even timers to create a 64 bit non-atomic counter which is racy in simple usage, hence the clock muxes are explicitly setup to individual 32 bit counters driven off system crystal (HFOSC) as default.
--- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 240 ++++++++++++++++++ .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 130 ++++++++++ 2 files changed, 370 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +240 -0
@@ -971,6 +971,246 @@ watchdog1: watchdog@2210000 { assigned-clock-parents = <&k3_clks 253 5>; }; + main_timer0: timer@2400000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2400000 0x00 0x400>; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 49 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 49 1>; + assigned-clock-parents = <&k3_clks 49 2>; + power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer1: timer@2410000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2410000 0x00 0x400>; + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 50 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 50 1>, <&k3_clks 313 0>; + assigned-clock-parents = <&k3_clks 50 2>, <&k3_clks 313 1>; + power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer2: timer@2420000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2420000 0x00 0x400>; + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 51 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 51 1>; + assigned-clock-parents = <&k3_clks 51 2>; + power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer3: timer@2430000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2430000 0x00 0x400>; + interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 52 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 52 1>, <&k3_clks 314 0>; + assigned-clock-parents = <&k3_clks 52 2>, <&k3_clks 314 1>; + power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer4: timer@2440000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2440000 0x00 0x400>; + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 53 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 53 1>; + assigned-clock-parents = <&k3_clks 53 2>; + power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer5: timer@2450000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2450000 0x00 0x400>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 54 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 54 1>, <&k3_clks 315 0>; + assigned-clock-parents = <&k3_clks 54 2>, <&k3_clks 315 1>; + power-domains = <&k3_pds 54 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer6: timer@2460000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2460000 0x00 0x400>; + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 55 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 55 1>; + assigned-clock-parents = <&k3_clks 55 2>; + power-domains = <&k3_pds 55 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer7: timer@2470000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2470000 0x00 0x400>; + interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 57 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 57 1>, <&k3_clks 316 0>; + assigned-clock-parents = <&k3_clks 57 2>, <&k3_clks 316 1>; + power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer8: timer@2480000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2480000 0x00 0x400>; + interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 58 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 58 1>; + assigned-clock-parents = <&k3_clks 58 2>; + power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer9: timer@2490000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2490000 0x00 0x400>; + interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 59 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 59 1>, <&k3_clks 317 0>; + assigned-clock-parents = <&k3_clks 59 2>, <&k3_clks 317 1>; + power-domains = <&k3_pds 59 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer10: timer@24a0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24a0000 0x00 0x400>; + interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 60 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 60 1>; + assigned-clock-parents = <&k3_clks 60 2>; + power-domains = <&k3_pds 60 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer11: timer@24b0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24b0000 0x00 0x400>; + interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 62 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 62 1>, <&k3_clks 318 0>; + assigned-clock-parents = <&k3_clks 62 2>, <&k3_clks 318 1>; + power-domains = <&k3_pds 62 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer12: timer@24c0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24c0000 0x00 0x400>; + interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 63 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 63 1>; + assigned-clock-parents = <&k3_clks 63 2>; + power-domains = <&k3_pds 63 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer13: timer@24d0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24d0000 0x00 0x400>; + interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 64 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 64 1>, <&k3_clks 319 0>; + assigned-clock-parents = <&k3_clks 64 2>, <&k3_clks 319 1>; + power-domains = <&k3_pds 64 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer14: timer@24e0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24e0000 0x00 0x400>; + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 65 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 65 1>; + assigned-clock-parents = <&k3_clks 65 2>; + power-domains = <&k3_pds 65 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer15: timer@24f0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24f0000 0x00 0x400>; + interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 66 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 66 1>, <&k3_clks 320 0>; + assigned-clock-parents = <&k3_clks 66 2>, <&k3_clks 320 1>; + power-domains = <&k3_pds 66 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer16: timer@2500000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2500000 0x00 0x400>; + interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 67 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 67 1>; + assigned-clock-parents = <&k3_clks 67 2>; + power-domains = <&k3_pds 67 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer17: timer@2510000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2510000 0x00 0x400>; + interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 68 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 68 1>, <&k3_clks 321 0>; + assigned-clock-parents = <&k3_clks 68 2>, <&k3_clks 321 1>; + power-domains = <&k3_pds 68 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer18: timer@2520000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2520000 0x00 0x400>; + interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 69 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 69 1>; + assigned-clock-parents = <&k3_clks 69 2>; + power-domains = <&k3_pds 69 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer19: timer@2530000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2530000 0x00 0x400>; + interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 70 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 70 1>, <&k3_clks 322 0>; + assigned-clock-parents = <&k3_clks 70 2>, <&k3_clks 322 1>; + power-domains = <&k3_pds 70 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + main_r5fss0: r5fss@5c00000 { compatible = "ti,j7200-r5fss"; ti,cluster-mode = <1>;
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +130 -0
136 lines not on this page · raw message
Signature · 1 line
2.34.1
PATCH v4 2/6 arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads
In reply to Udit KumarThere are timer IO pads in the MCU domain, and in the MAIN domain. These pads can be muxed for the related timers.
There are timer IO control registers for input and output. The registers for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and CTRLMMR_MCU_TIMERIO*_CTRL the output.
The multiplexing is documented in TRM "5.1.2.3.1.4 Timer IO Muxing Control Registers" and "5.1.3.3.1.5 Timer IO Muxing Control Registers", and the CASCADE_EN bit is documented in TRM "12.6.3.1 Timers Overview".
For chaining timers, the timer IO control registers also have a CASCADE_EN input bit in the CTRLMMR_TIMER*_CTRL in the registers. The CASCADE_EN bit muxes the previous timer output, or possibly and external TIMER_IO pad source, to the input clock of the selected timer instance for odd numered timers. For the even numbered timers, the CASCADE_EN bit does not do anything. The timer cascade input routing options are shown in TRM "Figure 12-3224. Timers Overview". For handling beyond multiplexing, the driver support for timer cascading should be likely be handled via the clock framework.
The MCU timer controls are also marked as reserved for usage by the MCU firmware.
--- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 18 +++++++++++++++++ .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 20 +++++++++++++++++++ 2 files changed, 38 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +18 -0
@@ -392,6 +392,24 @@ cpts@3d000 { }; }; + /* TIMERIO pad input CTRLMMR_TIMER*_CTRL registers */ + main_timerio_input: pinctrl@104200 { + compatible = "pinctrl-single"; + reg = <0x0 0x104200 0x0 0x50>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x000001ff>; + }; + + /* TIMERIO pad output CTCTRLMMR_TIMERIO*_CTRL registers */ + main_timerio_output: pinctrl@104280 { + compatible = "pinctrl-single"; + reg = <0x0 0x104280 0x0 0x20>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x0000001f>; + }; + main_pmx0: pinctrl@11c000 { compatible = "pinctrl-single"; /* Proxy 0 addressing */
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +20 -0
@@ -183,6 +183,26 @@ chipid@43000014 { reg = <0x00 0x43000014 0x00 0x4>; }; + /* MCU_TIMERIO pad input CTRLMMR_MCU_TIMER*_CTRL registers */ + mcu_timerio_input: pinctrl@40f04200 { + compatible = "pinctrl-single"; + reg = <0x0 0x40f04200 0x0 0x28>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x0000000F>; + status = "reserved"; + }; + + /* MCU_TIMERIO pad output CTRLMMR_MCU_TIMERIO*_CTRL registers */ + mcu_timerio_output: pinctrl@40f04280 { + compatible = "pinctrl-single"; + reg = <0x0 0x40f04280 0x0 0x28>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x0000000F>; + status = "reserved"; + }; + wkup_pmx0: pinctrl@4301c000 { compatible = "pinctrl-single"; /* Proxy 0 addressing */
Signature · 1 line
2.34.1
PATCH v4 3/6 arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0 pin mux
In reply to Udit Kumarmain_i2c0 pin mux was duplicated in som and common file. So removing duplicated node from common file.
--- arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 7 ------- 1 file changed, 7 deletions(-)
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +0 -7
@@ -106,13 +106,6 @@ J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */ }; &main_pmx0 { - main_i2c0_pins_default: main-i2c0-pins-default { - pinctrl-single,pins = < - J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */ - J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ - >; - }; - main_i2c1_pins_default: main-i2c1-pins-default { pinctrl-single,pins = < J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
Signature · 1 line
2.34.1
PATCH v4 4/6 arm64: dts: ti: k3-j7200-common-proc-board: Add uart pinmux
In reply to Udit KumarAdd main, mcu, wakeup domain uart0 pin mux into common board file and it's reference to uart node.
--- .../dts/ti/k3-j7200-common-proc-board.dts | 58 ++++++++++++++++++- 1 file changed, 57 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +57 -1
@@ -79,6 +79,24 @@ vdd_sd_dv: gpio-regulator-TLV71033 { }; }; +&wkup_pmx0 { + mcu_uart0_pins_default: mcu-uart0-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xf4, PIN_INPUT, 0) /* (D20) MCU_UART0_RXD */ + J721E_WKUP_IOPAD(0xf0, PIN_OUTPUT, 0) /* (D19) MCU_UART0_TXD */ + J721E_WKUP_IOPAD(0xf8, PIN_INPUT, 0) /* (E20) MCU_UART0_CTSn */ + J721E_WKUP_IOPAD(0xfc, PIN_OUTPUT, 0) /* (E21) MCU_UART0_RTSn */ + >; + }; + + wkup_uart0_pins_default: wkup-uart0-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xb0, PIN_INPUT, 0) /* (B14) WKUP_UART0_RXD */ + J721E_WKUP_IOPAD(0xb4, PIN_OUTPUT, 0) /* (A14) WKUP_UART0_TXD */ + >; + }; +}; + &wkup_pmx2 { mcu_cpsw_pins_default: mcu-cpsw-pins-default { pinctrl-single,pins = <
@@ -106,6 +124,29 @@ J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */ }; &main_pmx0 { + main_uart0_pins_default: main-uart0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */ + J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */ + J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */ + J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */ + >; + }; + + main_uart1_pins_default: main-uart1-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0xb8, PIN_INPUT, 0) /* (T18) UART1_RXD */ + J721E_IOPAD(0xbc, PIN_INPUT, 0) /* (T20) UART1_TXD */ + >; + }; + + main_uart3_pins_default: main-uart3-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0x60, PIN_INPUT, 11) /* (T15) MCAN8_TX.UART3_CTSn */ + J721E_IOPAD(0x30, PIN_INPUT, 11) /* (Y18) MCAN2_TX.UART3_RXD */ + >; + }; + main_i2c1_pins_default: main-i2c1-pins-default { pinctrl-single,pins = < J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
@@ -144,22 +185,30 @@ J721E_IOPAD(0x04, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */ &wkup_uart0 { /* Wakeup UART is used by System firmware */ status = "reserved"; + pinctrl-names = "default"; + pinctrl-0 = <&wkup_uart0_pins_default>; }; &mcu_uart0 { status = "okay"; - /* Default pinmux */ + pinctrl-names = "default"; + pinctrl-0 = <&mcu_uart0_pins_default>; + clock-frequency = <96000000>; }; &main_uart0 { status = "okay"; /* Shared with ATF on this platform */ power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart0_pins_default>; }; &main_uart1 { status = "okay"; /* Default pinmux */ + pinctrl-names = "default"; + pinctrl-0 = <&main_uart1_pins_default>; }; &main_uart2 {
@@ -167,6 +216,13 @@ &main_uart2 { status = "reserved"; }; +&main_uart3 { + /* Shared with MCAN Interface */ + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart3_pins_default>; +}; + &main_gpio2 { status = "disabled"; };
Signature · 1 line
2.34.1
PATCH v4 5/6 arm64: dts: ti: k3-j7200-common-proc-board: Define aliases at board level
In reply to Udit KumarDefine aliases at board level
--- arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +10 -0
@@ -15,6 +15,16 @@ / { compatible = "ti,j7200-evm", "ti,j7200"; model = "Texas Instruments J7200 EVM"; + aliases { + serial0 = &wkup_uart0; + serial1 = &mcu_uart0; + serial2 = &main_uart0; + serial3 = &main_uart1; + serial5 = &main_uart3; + mmc0 = &main_sdhci0; + mmc1 = &main_sdhci1; + }; + chosen { stdout-path = "serial2:115200n8"; };
Signature · 1 line
2.34.1
PATCH v4 6/6 arm64: dts: ti: k3-j7200: Drop SoC level aliases
In reply to Udit KumarAiases are defined at board level, so dropping from soc level
--- arch/arm64/boot/dts/ti/k3-j7200.dtsi | 17 ----------------- 1 file changed, 17 deletions(-)
arch/arm64/boot/dts/ti/k3-j7200.dtsi +0 -17
@@ -18,23 +18,6 @@ / { #address-cells = <2>; #size-cells = <2>; - aliases { - serial0 = &wkup_uart0; - serial1 = &mcu_uart0; - serial2 = &main_uart0; - serial3 = &main_uart1; - serial4 = &main_uart2; - serial5 = &main_uart3; - serial6 = &main_uart4; - serial7 = &main_uart5; - serial8 = &main_uart6; - serial9 = &main_uart7; - serial10 = &main_uart8; - serial11 = &main_uart9; - mmc0 = &main_sdhci0; - mmc1 = &main_sdhci1; - }; - chosen { }; cpus {
Signature · 1 line
2.34.1
Quoted 4 lines · Udit Kumar
In continuation of patch series posted by Nishanth for sync of uboot device tree with kernel device tree for AM64 SOC.
https://lore.kernel.org/linux-arm-kernel/[email protected]/This series extend device tree sync/clean up for J7200 SOC.
Thank you for the cleanup. For the series:
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Hi Udit Kumar,
Quoted 9 lines · Udit Kumar
In continuation of patch series posted by Nishanth for sync of uboot device tree with kernel device tree for AM64 SOC.
https://lore.kernel.org/linux-arm-kernel/[email protected]/This series extend device tree sync/clean up for J7200 SOC.
This patch series build on top of
https://lore.kernel.org/all/[email protected][...]
I have applied the following to branch ti-k3-dts-next on [1]. Thank you!
[1/6] arm64: dts: ti: k3-j7200: Add general purpose timers
commit: c8a28ed4837ce03254e0941f4fbc8364b1e78543
[2/6] arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads
commit: 03612d384621ffe21c6d338de916251d1bfd84fa
[3/6] arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0 pin mux
commit: 7f58e2b418d89f38f242b04da5a1dd93a2c514fd
[4/6] arm64: dts: ti: k3-j7200-common-proc-board: Add uart pinmux
commit: 3709ea7f960ed77ac29af692c9e32351060400d9
[5/6] arm64: dts: ti: k3-j7200-common-proc-board: Define aliases at board level
commit: c4ba159fff90791956370ce93c130aadea87dbb6
[6/6] arm64: dts: ti: k3-j7200: Drop SoC level aliases
commit: 858dde8a3f56f0b7a0c217ac4abf56e34c34ae74All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh