Skip to contentSkip to conversation

drm: bridge: dw-mipi-dsi: Fix enable/disable of DSI controller

PATCH Superseded Ondřej Jirman 2 participants 3 messages Jun 17, 2023

Subsystems (4)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 drm: bridge: dw-mipi-dsi: Fix enable/disable of DSI controller

From: Ondrej Jirman <[email protected]>

Before this patch, booting to Linux VT and doing a simple:

echo 2 > /sys/class/graphics/fb0/blank
echo 0 > /sys/class/graphics/fb0/blank

would result in failures to re-enable the panel. Mode set callback is called only once during boot in this scenario, while calls to enable/disable callbacks are balanced afterwards. The driver doesn't work unless userspace calls modeset before enabling the CRTC/connector.

This patch moves enabling of the DSI host from mode_set into pre_enable callback, and removes some old hacks where this bridge driver is directly calling into other bridge driver's callbacks.

pre_enable_prev_first flag is set on the panel's bridge so that panel drivers will get their prepare function called between DSI host's pre_enable and enable callbacks, so that they get a chance to perform panel setup while DSI host is already enabled in command mode. Otherwise panel's prepare would be called before DSI host is enabled, and any DSI communication used in prepare callback would fail.

With all these changes, the enable/disable sequence is now well balanced, and host's and panel's callbacks are called in proper order documented in the drm_panel API documentation without needing the old hacks. (Mainly that panel->prepare is called when DSI host is ready to allow the panel driver to send DSI commands and vice versa during disable.)

Tested on Pinephone Pro. Trace of the callbacks follows.

Before:

[    1.253882] dw-mipi-dsi-rockchip ff960000.dsi: mode_set
[    1.290732] panel-himax-hx8394 ff960000.dsi.0: prepare
[    1.475576] dw-mipi-dsi-rockchip ff960000.dsi: enable
[    1.475593] panel-himax-hx8394 ff960000.dsi.0: enable

echo 2 > /sys/class/graphics/fb0/blank

[   13.722799] panel-himax-hx8394 ff960000.dsi.0: disable
[   13.774502] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[   13.774526] panel-himax-hx8394 ff960000.dsi.0: unprepare

echo 0 > /sys/class/graphics/fb0/blank

[   17.735796] panel-himax-hx8394 ff960000.dsi.0: prepare
[   17.923522] dw-mipi-dsi-rockchip ff960000.dsi: enable
[   17.923540] panel-himax-hx8394 ff960000.dsi.0: enable
[   17.944330] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[   17.944335] panel-himax-hx8394 ff960000.dsi.0: sending command 0xb9 failed: -110
[   17.944340] panel-himax-hx8394 ff960000.dsi.0: Panel init sequence failed: -110

echo 2 > /sys/class/graphics/fb0/blank

[  431.148583] panel-himax-hx8394 ff960000.dsi.0: disable
[  431.169259] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[  431.169268] panel-himax-hx8394 ff960000.dsi.0: Failed to enter sleep mode: -110
[  431.169282] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[  431.169316] panel-himax-hx8394 ff960000.dsi.0: unprepare
[  431.169357] pclk_mipi_dsi0 already disabled

echo 0 > /sys/class/graphics/fb0/blank

[  432.796851] panel-himax-hx8394 ff960000.dsi.0: prepare
[  432.981537] dw-mipi-dsi-rockchip ff960000.dsi: enable
[  432.981568] panel-himax-hx8394 ff960000.dsi.0: enable
[  433.002290] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[  433.002299] panel-himax-hx8394 ff960000.dsi.0: sending command 0xb9 failed: -110
[  433.002312] panel-himax-hx8394 ff960000.dsi.0: Panel init sequence failed: -110

-----------------------------------------------------------------------

After:

[    1.248372] dw-mipi-dsi-rockchip ff960000.dsi: mode_set
[    1.248704] dw-mipi-dsi-rockchip ff960000.dsi: pre_enable
[    1.285377] panel-himax-hx8394 ff960000.dsi.0: prepare
[    1.468392] dw-mipi-dsi-rockchip ff960000.dsi: enable
[    1.468421] panel-himax-hx8394 ff960000.dsi.0: enable

echo 2 > /sys/class/graphics/fb0/blank

[   16.210357] panel-himax-hx8394 ff960000.dsi.0: disable
[   16.261315] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[   16.261339] panel-himax-hx8394 ff960000.dsi.0: unprepare

echo 0 > /sys/class/graphics/fb0/blank

[   19.161453] dw-mipi-dsi-rockchip ff960000.dsi: pre_enable
[   19.197869] panel-himax-hx8394 ff960000.dsi.0: prepare
[   19.382141] dw-mipi-dsi-rockchip ff960000.dsi: enable
[   19.382158] panel-himax-hx8394 ff960000.dsi.0: enable
---
 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 28 +++++++++++--------
 1 file changed, 16 insertions(+), 12 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +16 -12
index b2efecf7d160..352c6829259a 100644
@@ -265,6 +265,7 @@ struct dw_mipi_dsi {
 	struct dw_mipi_dsi *master; /* dual-dsi master ptr */
 	struct dw_mipi_dsi *slave; /* dual-dsi slave ptr */
 
+	struct drm_display_mode mode;
 	const struct dw_mipi_dsi_plat_data *plat_data;
 };
 
@@ -332,6 +333,7 @@ static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
 	if (IS_ERR(bridge))
 		return PTR_ERR(bridge);
 
+	bridge->pre_enable_prev_first = true;
 	dsi->panel_bridge = bridge;
 
 	drm_bridge_add(&dsi->bridge);
@@ -859,15 +861,6 @@ static void dw_mipi_dsi_bridge_post_atomic_disable(struct drm_bridge *bridge,
 	 */
 	dw_mipi_dsi_set_mode(dsi, 0);
 
-	/*
-	 * TODO Only way found to call panel-bridge post_disable &
-	 * panel unprepare before the dsi "final" disable...
-	 * This needs to be fixed in the drm_bridge framework and the API
-	 * needs to be updated to manage our own call chains...
-	 */
-	if (dsi->panel_bridge->funcs->post_disable)
-		dsi->panel_bridge->funcs->post_disable(dsi->panel_bridge);
-
 	if (phy_ops->power_off)
 		phy_ops->power_off(dsi->plat_data->priv_data);
 
@@ -942,15 +935,25 @@ static void dw_mipi_dsi_mode_set(struct dw_mipi_dsi *dsi,
 		phy_ops->power_on(dsi->plat_data->priv_data);
 }
 
+static void dw_mipi_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
+						 struct drm_bridge_state *old_bridge_state)
+{
+	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
+
+	/* Power up the dsi ctl into a command mode */
+	dw_mipi_dsi_mode_set(dsi, &dsi->mode);
+	if (dsi->slave)
+		dw_mipi_dsi_mode_set(dsi->slave, &dsi->mode);
+}
+
 static void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge,
 					const struct drm_display_mode *mode,
 					const struct drm_display_mode *adjusted_mode)
 {
 	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
 
-	dw_mipi_dsi_mode_set(dsi, adjusted_mode);
-	if (dsi->slave)
-		dw_mipi_dsi_mode_set(dsi->slave, adjusted_mode);
+	/* Store the display mode for later use in pre_enable callback */
+	memcpy(&dsi->mode, adjusted_mode, sizeof(dsi->mode));
 }
 
 static void dw_mipi_dsi_bridge_atomic_enable(struct drm_bridge *bridge,
@@ -1004,6 +1007,7 @@ static const struct drm_bridge_funcs dw_mipi_dsi_bridge_funcs = {
 	.atomic_duplicate_state	= drm_atomic_helper_bridge_duplicate_state,
 	.atomic_destroy_state	= drm_atomic_helper_bridge_destroy_state,
 	.atomic_reset		= drm_atomic_helper_bridge_reset,
+	.atomic_pre_enable	= dw_mipi_dsi_bridge_atomic_pre_enable,
 	.atomic_enable		= dw_mipi_dsi_bridge_atomic_enable,
 	.atomic_post_disable	= dw_mipi_dsi_bridge_post_atomic_disable,
 	.mode_set		= dw_mipi_dsi_bridge_mode_set,
Signature · 1 line
2.41.0
Reviewed-by on v1 1/1
#1 lore raw

Hi Ondřej,

Quoted 89 lines · Ondřej Jirman

From: Ondrej Jirman <[email protected]>

Before this patch, booting to Linux VT and doing a simple:

echo 2 > /sys/class/graphics/fb0/blank
echo 0 > /sys/class/graphics/fb0/blank

would result in failures to re-enable the panel. Mode set callback is called only once during boot in this scenario, while calls to enable/disable callbacks are balanced afterwards. The driver doesn't work unless userspace calls modeset before enabling the CRTC/connector.

This patch moves enabling of the DSI host from mode_set into pre_enable callback, and removes some old hacks where this bridge driver is directly calling into other bridge driver's callbacks.

pre_enable_prev_first flag is set on the panel's bridge so that panel drivers will get their prepare function called between DSI host's pre_enable and enable callbacks, so that they get a chance to perform panel setup while DSI host is already enabled in command mode. Otherwise panel's prepare would be called before DSI host is enabled, and any DSI communication used in prepare callback would fail.

With all these changes, the enable/disable sequence is now well balanced, and host's and panel's callbacks are called in proper order documented in the drm_panel API documentation without needing the old hacks. (Mainly that panel->prepare is called when DSI host is ready to allow the panel driver to send DSI commands and vice versa during disable.)

Tested on Pinephone Pro. Trace of the callbacks follows.

Before:

[    1.253882] dw-mipi-dsi-rockchip ff960000.dsi: mode_set
[    1.290732] panel-himax-hx8394 ff960000.dsi.0: prepare
[    1.475576] dw-mipi-dsi-rockchip ff960000.dsi: enable
[    1.475593] panel-himax-hx8394 ff960000.dsi.0: enable

echo 2 > /sys/class/graphics/fb0/blank

[   13.722799] panel-himax-hx8394 ff960000.dsi.0: disable
[   13.774502] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[   13.774526] panel-himax-hx8394 ff960000.dsi.0: unprepare

echo 0 > /sys/class/graphics/fb0/blank

[   17.735796] panel-himax-hx8394 ff960000.dsi.0: prepare
[   17.923522] dw-mipi-dsi-rockchip ff960000.dsi: enable
[   17.923540] panel-himax-hx8394 ff960000.dsi.0: enable
[   17.944330] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[   17.944335] panel-himax-hx8394 ff960000.dsi.0: sending command 0xb9 failed: -110
[   17.944340] panel-himax-hx8394 ff960000.dsi.0: Panel init sequence failed: -110

echo 2 > /sys/class/graphics/fb0/blank

[  431.148583] panel-himax-hx8394 ff960000.dsi.0: disable
[  431.169259] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[  431.169268] panel-himax-hx8394 ff960000.dsi.0: Failed to enter sleep mode: -110
[  431.169282] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[  431.169316] panel-himax-hx8394 ff960000.dsi.0: unprepare
[  431.169357] pclk_mipi_dsi0 already disabled

echo 0 > /sys/class/graphics/fb0/blank

[  432.796851] panel-himax-hx8394 ff960000.dsi.0: prepare
[  432.981537] dw-mipi-dsi-rockchip ff960000.dsi: enable
[  432.981568] panel-himax-hx8394 ff960000.dsi.0: enable
[  433.002290] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[  433.002299] panel-himax-hx8394 ff960000.dsi.0: sending command 0xb9 failed: -110
[  433.002312] panel-himax-hx8394 ff960000.dsi.0: Panel init sequence failed: -110

-----------------------------------------------------------------------

After:

[    1.248372] dw-mipi-dsi-rockchip ff960000.dsi: mode_set
[    1.248704] dw-mipi-dsi-rockchip ff960000.dsi: pre_enable
[    1.285377] panel-himax-hx8394 ff960000.dsi.0: prepare
[    1.468392] dw-mipi-dsi-rockchip ff960000.dsi: enable
[    1.468421] panel-himax-hx8394 ff960000.dsi.0: enable

echo 2 > /sys/class/graphics/fb0/blank

[   16.210357] panel-himax-hx8394 ff960000.dsi.0: disable
[   16.261315] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[   16.261339] panel-himax-hx8394 ff960000.dsi.0: unprepare
Quoted 8 lines

echo 0 > /sys/class/graphics/fb0/blank

[   19.161453] dw-mipi-dsi-rockchip ff960000.dsi: pre_enable
[   19.197869] panel-himax-hx8394 ff960000.dsi.0: prepare
[   19.382141] dw-mipi-dsi-rockchip ff960000.dsi: enable
[   19.382158] panel-himax-hx8394 ff960000.dsi.0: enable

Nice cleanup and fix.
Have you consider if this need a Fixes: ?

Quoted 57 lines
---
 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 28 +++++++++++--------
 1 file changed, 16 insertions(+), 12 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +13 -9
index b2efecf7d160..352c6829259a 100644
@@ -265,6 +265,7 @@ struct dw_mipi_dsi {
 	struct dw_mipi_dsi *master; /* dual-dsi master ptr */
 	struct dw_mipi_dsi *slave; /* dual-dsi slave ptr */
 
+	struct drm_display_mode mode;
 	const struct dw_mipi_dsi_plat_data *plat_data;
 };
 
@@ -332,6 +333,7 @@ static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
 	if (IS_ERR(bridge))
 		return PTR_ERR(bridge);
 
+	bridge->pre_enable_prev_first = true;
 	dsi->panel_bridge = bridge;
 
 	drm_bridge_add(&dsi->bridge);
@@ -859,15 +861,6 @@ static void dw_mipi_dsi_bridge_post_atomic_disable(struct drm_bridge *bridge,
 	 */
 	dw_mipi_dsi_set_mode(dsi, 0);
 
-	/*
-	 * TODO Only way found to call panel-bridge post_disable &
-	 * panel unprepare before the dsi "final" disable...
-	 * This needs to be fixed in the drm_bridge framework and the API
-	 * needs to be updated to manage our own call chains...
-	 */
-	if (dsi->panel_bridge->funcs->post_disable)
-		dsi->panel_bridge->funcs->post_disable(dsi->panel_bridge);
-
 	if (phy_ops->power_off)
 		phy_ops->power_off(dsi->plat_data->priv_data);
 
@@ -942,15 +935,25 @@ static void dw_mipi_dsi_mode_set(struct dw_mipi_dsi *dsi,
 		phy_ops->power_on(dsi->plat_data->priv_data);
 }
 
+static void dw_mipi_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
+						 struct drm_bridge_state *old_bridge_state)
+{
+	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
+
+	/* Power up the dsi ctl into a command mode */
+	dw_mipi_dsi_mode_set(dsi, &dsi->mode);
+	if (dsi->slave)
+		dw_mipi_dsi_mode_set(dsi->slave, &dsi->mode);
+}
+
 static void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge,
 					const struct drm_display_mode *mode,

drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c static void dw_mipi_dsi_mode_set(struct dw_mipi_dsi *dsi, · line 957

Quoted 10 lines
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +2 -3
 					const struct drm_display_mode *adjusted_mode)
 {
 	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
 
-	dw_mipi_dsi_mode_set(dsi, adjusted_mode);
-	if (dsi->slave)
-		dw_mipi_dsi_mode_set(dsi->slave, adjusted_mode);
+	/* Store the display mode for later use in pre_enable callback */
+	memcpy(&dsi->mode, adjusted_mode, sizeof(dsi->mode));
 }

Use drm_mode_copy here.
With this fixed:

#2 lore raw

Hello Sam,

Quoted 100 lines · Sam Ravnborg

Hi Ondřej,

Quoted 96 lines · Ondřej Jirman

From: Ondrej Jirman <[email protected]>

Before this patch, booting to Linux VT and doing a simple:

echo 2 > /sys/class/graphics/fb0/blank
echo 0 > /sys/class/graphics/fb0/blank

would result in failures to re-enable the panel. Mode set callback is called only once during boot in this scenario, while calls to enable/disable callbacks are balanced afterwards. The driver doesn't work unless userspace calls modeset before enabling the CRTC/connector.

This patch moves enabling of the DSI host from mode_set into pre_enable callback, and removes some old hacks where this bridge driver is directly calling into other bridge driver's callbacks.

pre_enable_prev_first flag is set on the panel's bridge so that panel drivers will get their prepare function called between DSI host's pre_enable and enable callbacks, so that they get a chance to perform panel setup while DSI host is already enabled in command mode. Otherwise panel's prepare would be called before DSI host is enabled, and any DSI communication used in prepare callback would fail.

With all these changes, the enable/disable sequence is now well balanced, and host's and panel's callbacks are called in proper order documented in the drm_panel API documentation without needing the old hacks. (Mainly that panel->prepare is called when DSI host is ready to allow the panel driver to send DSI commands and vice versa during disable.)

Tested on Pinephone Pro. Trace of the callbacks follows.

Before:

[    1.253882] dw-mipi-dsi-rockchip ff960000.dsi: mode_set
[    1.290732] panel-himax-hx8394 ff960000.dsi.0: prepare
[    1.475576] dw-mipi-dsi-rockchip ff960000.dsi: enable
[    1.475593] panel-himax-hx8394 ff960000.dsi.0: enable

echo 2 > /sys/class/graphics/fb0/blank

[   13.722799] panel-himax-hx8394 ff960000.dsi.0: disable
[   13.774502] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[   13.774526] panel-himax-hx8394 ff960000.dsi.0: unprepare

echo 0 > /sys/class/graphics/fb0/blank

[   17.735796] panel-himax-hx8394 ff960000.dsi.0: prepare
[   17.923522] dw-mipi-dsi-rockchip ff960000.dsi: enable
[   17.923540] panel-himax-hx8394 ff960000.dsi.0: enable
[   17.944330] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[   17.944335] panel-himax-hx8394 ff960000.dsi.0: sending command 0xb9 failed: -110
[   17.944340] panel-himax-hx8394 ff960000.dsi.0: Panel init sequence failed: -110

echo 2 > /sys/class/graphics/fb0/blank

[  431.148583] panel-himax-hx8394 ff960000.dsi.0: disable
[  431.169259] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[  431.169268] panel-himax-hx8394 ff960000.dsi.0: Failed to enter sleep mode: -110
[  431.169282] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[  431.169316] panel-himax-hx8394 ff960000.dsi.0: unprepare
[  431.169357] pclk_mipi_dsi0 already disabled

echo 0 > /sys/class/graphics/fb0/blank

[  432.796851] panel-himax-hx8394 ff960000.dsi.0: prepare
[  432.981537] dw-mipi-dsi-rockchip ff960000.dsi: enable
[  432.981568] panel-himax-hx8394 ff960000.dsi.0: enable
[  433.002290] dw-mipi-dsi-rockchip ff960000.dsi: failed to write command FIFO
[  433.002299] panel-himax-hx8394 ff960000.dsi.0: sending command 0xb9 failed: -110
[  433.002312] panel-himax-hx8394 ff960000.dsi.0: Panel init sequence failed: -110

-----------------------------------------------------------------------

After:

[    1.248372] dw-mipi-dsi-rockchip ff960000.dsi: mode_set
[    1.248704] dw-mipi-dsi-rockchip ff960000.dsi: pre_enable
[    1.285377] panel-himax-hx8394 ff960000.dsi.0: prepare
[    1.468392] dw-mipi-dsi-rockchip ff960000.dsi: enable
[    1.468421] panel-himax-hx8394 ff960000.dsi.0: enable

echo 2 > /sys/class/graphics/fb0/blank

[   16.210357] panel-himax-hx8394 ff960000.dsi.0: disable
[   16.261315] dw-mipi-dsi-rockchip ff960000.dsi: post_disable
[   16.261339] panel-himax-hx8394 ff960000.dsi.0: unprepare

echo 0 > /sys/class/graphics/fb0/blank

[   19.161453] dw-mipi-dsi-rockchip ff960000.dsi: pre_enable
[   19.197869] panel-himax-hx8394 ff960000.dsi.0: prepare
[   19.382141] dw-mipi-dsi-rockchip ff960000.dsi: enable
[   19.382158] panel-himax-hx8394 ff960000.dsi.0: enable
Quoted 4 lines
Quoted 1 line

Nice cleanup and fix.
Have you consider if this need a Fixes: ?

It might be useful, I'll hunt for some some useful base for a Fixes tag.

Quoted 62 lines
Quoted 62 lines
---
 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 28 +++++++++++--------
 1 file changed, 16 insertions(+), 12 deletions(-)
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +13 -9
index b2efecf7d160..352c6829259a 100644
@@ -265,6 +265,7 @@ struct dw_mipi_dsi {
 	struct dw_mipi_dsi *master; /* dual-dsi master ptr */
 	struct dw_mipi_dsi *slave; /* dual-dsi slave ptr */
 
+	struct drm_display_mode mode;
 	const struct dw_mipi_dsi_plat_data *plat_data;
 };
 
@@ -332,6 +333,7 @@ static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
 	if (IS_ERR(bridge))
 		return PTR_ERR(bridge);
 
+	bridge->pre_enable_prev_first = true;
 	dsi->panel_bridge = bridge;
 
 	drm_bridge_add(&dsi->bridge);
@@ -859,15 +861,6 @@ static void dw_mipi_dsi_bridge_post_atomic_disable(struct drm_bridge *bridge,
 	 */
 	dw_mipi_dsi_set_mode(dsi, 0);
 
-	/*
-	 * TODO Only way found to call panel-bridge post_disable &
-	 * panel unprepare before the dsi "final" disable...
-	 * This needs to be fixed in the drm_bridge framework and the API
-	 * needs to be updated to manage our own call chains...
-	 */
-	if (dsi->panel_bridge->funcs->post_disable)
-		dsi->panel_bridge->funcs->post_disable(dsi->panel_bridge);
-
 	if (phy_ops->power_off)
 		phy_ops->power_off(dsi->plat_data->priv_data);
 
@@ -942,15 +935,25 @@ static void dw_mipi_dsi_mode_set(struct dw_mipi_dsi *dsi,
 		phy_ops->power_on(dsi->plat_data->priv_data);
 }
 
+static void dw_mipi_dsi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
+						 struct drm_bridge_state *old_bridge_state)
+{
+	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
+
+	/* Power up the dsi ctl into a command mode */
+	dw_mipi_dsi_mode_set(dsi, &dsi->mode);
+	if (dsi->slave)
+		dw_mipi_dsi_mode_set(dsi->slave, &dsi->mode);
+}
+
 static void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge,
 					const struct drm_display_mode *mode,
 					const struct drm_display_mode *adjusted_mode)
 {
 	struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
 
Quoted 7 lines

drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c static void dw_mipi_dsi_mode_set(struct dw_mipi_dsi *dsi, · line 957

Quoted 6 lines
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c +2 -3
-	dw_mipi_dsi_mode_set(dsi, adjusted_mode);
-	if (dsi->slave)
-		dw_mipi_dsi_mode_set(dsi->slave, adjusted_mode);
+	/* Store the display mode for later use in pre_enable callback */
+	memcpy(&dsi->mode, adjusted_mode, sizeof(dsi->mode));
 }

Use drm_mode_copy here.

Ok.

Quoted 3 lines

With this fixed:

thank you,
Ondrej