mips: ralink: add complete clock and reset driver for mtmips SoCs
Subsystems (6)
Sergio Paracuellos
maintainerv5 cover mips: ralink: add complete clock and reset driver for mtmips SoCs
Hi all!
This patchset is a big effort to properly implement a clock and reset driver for old ralink SoCs. This allow to properly define clocks in device tree and avoid to use fixed-clocks directly from 'arch/mips/ralink' architecture directory code.
Device tree 'sysc' node will be both clock and reset provider using 'clock-cells' and 'reset-cells' properties.
The ralink SoCs we are taking about are RT2880, RT3050, RT3052, RT3350, RT3352, RT3883, RT5350, MT7620, MT7628 and MT7688. Mostly the code in this new driver has been extracted from 'arch/mips/ralink' and cleanly put using kernel clock and reset driver APIs. The clock plans for this SoCs only talks about relation between CPU frequency and BUS frequency. This relation is different depending on the particular SoC. CPU clock is derived from XTAL frequencies.
Depending on the SoC we have the following frequencies:
* RT2880 SoC:
- XTAL: 40 MHz.
- CPU: 250, 266, 280 or 300 MHz.
- BUS: CPU / 2 MHz.
* RT3050, RT3052, RT3350:
- XTAL: 40 MHz.
- CPU: 320 or 384 MHz.
- BUS: CPU / 3 MHz.
* RT3352:
- XTAL: 40 MHz.
- CPU: 384 or 400 MHz.
- BUS: CPU / 3 MHz.
- PERIPH: 40 MHz.
* RT3383:
- XTAL: 40 MHz.
- CPU: 250, 384, 480 or 500 MHz.
- BUS: Depends on RAM Type and CPU:
+ RAM DDR2: 125. ELSE 83 MHz.
+ RAM DDR2: 128. ELSE 96 MHz.
+ RAM DDR2: 160. ELSE 120 MHz.
+ RAM DDR2: 166. ELSE 125 MHz.
* RT5350:
- XTAL: 40 MHz.
- CPU: 300, 320 or 360 MHz.
- BUS: CPU / 3, CPU / 4, CPU / 3 MHz.
- PERIPH: 40 MHz.
* MT7628 and MT7688:
- XTAL: 20 MHz or 40 MHz.
- CPU: 575 or 580 MHz.
- BUS: CPU / 3.
- PCMI2S: 480 MHz.
- PERIPH: 40 MHz.
* MT7620:
- XTAL: 20 MHz or 40 MHz.
- PLL: XTAL, 480, 600 MHz.
- CPU: depends on PLL and some mult and dividers.
- BUS: depends on PLL and some mult and dividers.
- PERIPH: 40 or XTAL MHz.
MT7620 is a bit more complex deriving CPU clock from a PLL and an bunch of register reads and predividers. To derive CPU and BUS frequencies in the MT7620 SoC 'mt7620_calc_rate()' helper is used.
In the case XTAL can have different frequencies and we need a different clock frequency for peripherals 'periph' clock in introduced. The rest of the peripherals present in the SoC just follow their parent frequencies.
I am using 'mtmips' inside for ralink clock driver. This is aligned with pinctrl series recently merged through pinctrl git tree [0].
I am maintaining ralink as prefix for compatible strings after discussions between Rob and Arinc in v2 of this series [1].
Changes have been compile tested for:
- RT2880
- RT3883
Changes have been properly tested in:
- RT5350 SoC based board (ALL5003 board)
- MT7620A SoC based board (Haier HW-L1W)
- MT7628AN SoC based board (Motorola MWR03)
All of them resulting in a working platform.
Dts files for these SoCs in-tree except MT7621 are incomplete. We are planning to align with openWRT files at some point and add extra needed changes. Hence I am not touching them at all in these series. If this is a problem, please let me know and I will update them.
Talking about merging this series I'd like all of the patches going through the MIPS tree if possible.
Thanks in advance for your time.
Best regards,
Sergio Paracuellos
Changes in v5:
- Address comments of Shiji Yang in v4.
- Make use 'of_find_compatible_node()' instead of 'of_find_node_by_name()' since node names must not be an ABI (Thanks Krzysztof!!!)
- Test this changes in mt7620a Soc based board and MT7628AN Soc based board (Thanks Shiji Yang!!!)
Changes in v4:
- Collect Reviewed-by and Acked-by tags.
- Pass proper data for 'ralink,rt3352-sysc' and 'ralink,rt3883-sysc' compatible string.
Changes in v3:
- Address Stephen comments in v2:
+ Drop unsused include '<linux/clk.h>'.
+ Add fixed and factor clocks when it makes sense.
+ Make 'mtmips_periph_clk_ops' named variable.
+ WARN_ON -> WARN_ON_ONCE.
+ Avoid CONFIG_USB dependent code. Introduce new 'mtmips_clk_regs_init'.
+ Don't validate the bindings in the driver.
+ Make const 'struct clk_init_data' used inside macros.
+ do_div -> div_u64.
+ Make use of dev_err_probe.
Changes in v2:
- Address bindings documentation changes pointed out by Krzysztof:
+ Rename the file into 'mediatek,mtmips-sysc.yaml'.
+ Redo commit subject and log message.
+ Order compatibles alphabetically.
+ Redo bindings description taking into account this is a system controller node which provides both clocks and resets to the world.
+ Drop label from example.
+ Use 'syscon' as node name in example.
+ Drop no sense 'ralink,rt2880-reset' compatible string
- Squash patches 6 and 7 together as pointed out by Stephen Boyd.
Previoous series:
v4: https://lore.kernel.org/linux-clk/[email protected]/T/#t
v3: https://lore.kernel.org/linux-mips/[email protected]/T/#mafbc1704938b94a367c4b6240d9880a67be1f92f
v2: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#t
v1: https://lore.kernel.org/linux-clk/[email protected]/T/#t
[0]: https://lore.kernel.org/linux-gpio/[email protected]/T/#t
[1]: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#mfe725b6e3382c6fb09736472a846cbbc84f264dc
Sergio Paracuellos (9):
dt-bindings: clock: add mtmips SoCs system controller
clk: ralink: add clock and reset driver for MTMIPS SoCs
mips: ralink: rt288x: remove clock related code
mips: ralink: rt305x: remove clock related code
mips: ralink: rt3883: remove clock related code
mips: ralink: mt7620: remove clock related code
mips: ralink: remove reset related code
mips: ralink: get cpu rate from new driver code
MAINTAINERS: add Mediatek MTMIPS Clock maintainer
.../bindings/clock/mediatek,mtmips-sysc.yaml | 64 + MAINTAINERS | 6 + arch/mips/include/asm/mach-ralink/mt7620.h | 35 - arch/mips/include/asm/mach-ralink/rt288x.h | 10 - arch/mips/include/asm/mach-ralink/rt305x.h | 21 - arch/mips/include/asm/mach-ralink/rt3883.h | 8 - arch/mips/ralink/clk.c | 61 +- arch/mips/ralink/common.h | 5 - arch/mips/ralink/mt7620.c | 226 ---- arch/mips/ralink/of.c | 4 - arch/mips/ralink/reset.c | 61 - arch/mips/ralink/rt288x.c | 31 - arch/mips/ralink/rt305x.c | 78 -- arch/mips/ralink/rt3883.c | 44 - drivers/clk/ralink/Kconfig | 7 + drivers/clk/ralink/Makefile | 1 + drivers/clk/ralink/clk-mtmips.c | 1115 +++++++++++++++++ 17 files changed, 1245 insertions(+), 532 deletions(-) create mode 100644 Documentation/devicetree/bindings/clock/mediatek,mtmips-sysc.yaml create mode 100644 drivers/clk/ralink/clk-mtmips.c
Signature · 1 line
2.25.1
Sergio Paracuellos
maintainerPATCH v5 1/9 dt-bindings: clock: add mtmips SoCs system controller
Adds device tree binding documentation for system controller node present in Mediatek MIPS and Ralink SOCs. This node is a clock and reset provider for the rest of the world. This covers RT2880, RT3050, RT3052, RT3350, RT3883, RT5350, MT7620, MT7628 and MT7688 SoCs.
--- .../bindings/clock/mediatek,mtmips-sysc.yaml | 64 +++++++++++++++++++ 1 file changed, 64 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/mediatek,mtmips-sysc.yaml
Documentation/devicetree/bindings/clock/mediatek,mtmips-sysc.yaml new file +64 -0
@@ -0,0 +1,64 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/mediatek,mtmips-sysc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MTMIPS SoCs System Controller + +maintainers: + - Sergio Paracuellos <[email protected]> + +description: | + MediaTek MIPS and Ralink SoCs provides a system controller to allow + to access to system control registers. These registers include clock + and reset related ones so this node is both clock and reset provider + for the rest of the world. + + These SoCs have an XTAL from where the cpu clock is + provided as well as derived clocks for the bus and the peripherals. + +properties: + compatible: + items: + - enum: + - ralink,mt7620-sysc + - ralink,mt7628-sysc + - ralink,mt7688-sysc + - ralink,rt2880-sysc + - ralink,rt3050-sysc + - ralink,rt3052-sysc + - ralink,rt3352-sysc + - ralink,rt3883-sysc + - ralink,rt5350-sysc + - const: syscon + + reg: + maxItems: 1 + + '#clock-cells': + description: + The first cell indicates the clock number. + const: 1 + + '#reset-cells': + description: + The first cell indicates the reset bit within the register. + const: 1 + +required: + - compatible + - reg + - '#clock-cells' + - '#reset-cells' + +additionalProperties: false + +examples: + - | + syscon@0 { + compatible = "ralink,rt5350-sysc", "syscon"; + reg = <0x0 0x100>; + #clock-cells = <1>; + #reset-cells = <1>; + };
Signature · 1 line
2.25.1
Sergio Paracuellos
maintainerPATCH v5 2/9 clk: ralink: add clock and reset driver for MTMIPS SoCs
In reply to Sergio ParacuellosUntil now, clock related code for old ralink SoCs was based in fixed clocks using 'clk_register_fixed_rate' and 'clkdev_create' directly doing in code and not using device tree at all for their definition. Including this driver is an effort to be able to define proper clocks using device tree and also cleaning all the clock and reset related code from 'arch/mips/ralink' dir. This clock and reset driver covers all the ralink SoCs but MT7621 which is the newest and provides gating and some differences that make it different from its predecesors. It has its own driver since some time ago. The ralink SoCs we are taking about are RT2880, RT3050, RT3052, RT3350, RT3352, RT3883, RT5350, MT7620, MT7628 and MT7688. Mostly the code in this new driver has been extracted from 'arch/mips/ralink' and cleanly put using kernel clock driver APIs. The clock plans for this SoCs only talks about relation between CPU frequency and BUS frequency. This relation is different depending on the particular SoC. CPU clock is derived from XTAL frequencies.
Depending on the SoC we have the following frequencies:
* RT2880 SoC:
- XTAL: 40 MHz.
- CPU: 250, 266, 280 or 300 MHz.
- BUS: CPU / 2 MHz.
* RT3050, RT3052, RT3350:
- XTAL: 40 MHz.
- CPU: 320 or 384 MHz.
- BUS: CPU / 3 MHz.
* RT3352:
- XTAL: 40 MHz.
- CPU: 384 or 400 MHz.
- BUS: CPU / 3 MHz.
- PERIPH: 40 MHz.
* RT3383:
- XTAL: 40 MHz.
- CPU: 250, 384, 480 or 500 MHz.
- BUS: Depends on RAM Type and CPU:
+ RAM DDR2: 125. ELSE 83 MHz.
+ RAM DDR2: 128. ELSE 96 MHz.
+ RAM DDR2: 160. ELSE 120 MHz.
+ RAM DDR2: 166. ELSE 125 MHz.
* RT5350:
- XTAL: 40 MHz.
- CPU: 300, 320 or 360 MHz.
- BUS: CPU / 3, CPU / 4, CPU / 3 MHz.
- PERIPH: 40 MHz.
* MT7628 and MT7688:
- XTAL: 20 MHz or 40 MHz.
- CPU: 575 or 580 MHz.
- BUS: CPU / 3.
- PCMI2S: 480 MHz.
- PERIPH: 40 MHz.
* MT7620:
- XTAL: 20 MHz or 40 MHz.
- PLL: XTAL, 480, 600 MHz.
- CPU: depends on PLL and some mult and dividers.
- BUS: depends on PLL and some mult and dividers.
- PERIPH: 40 or XTAL MHz.
MT7620 is a bit more complex deriving CPU clock from a PLL and an bunch of register reads and predividers. To derive CPU and BUS frequencies in the MT7620 SoC 'mt7620_calc_rate()' helper is used.
In the case XTAL can have different frequencies and we need a different clock frequency for peripherals 'periph' clock in introduced.
The rest of the peripherals present in the SoC just follow their parent frequencies.
With this information the clk driver will provide all the clock and reset functionality from a set of hardcoded clocks allowing to define a nice device tree without fixed clocks.
--- drivers/clk/ralink/Kconfig | 7 + drivers/clk/ralink/Makefile | 1 + drivers/clk/ralink/clk-mtmips.c | 1115 +++++++++++++++++++++++++++++++ 3 files changed, 1123 insertions(+) create mode 100644 drivers/clk/ralink/clk-mtmips.c
drivers/clk/ralink/Kconfig +7 -0
@@ -9,3 +9,10 @@ config CLK_MT7621 select MFD_SYSCON help This driver supports MediaTek MT7621 basic clocks. + +config CLK_MTMIPS + bool "Clock driver for MTMIPS SoCs" + depends on SOC_RT305X || SOC_RT288X || SOC_RT3883 || SOC_MT7620 || COMPILE_TEST + select MFD_SYSCON + help + This driver supports MTMIPS basic clocks.
drivers/clk/ralink/Makefile +1 -0
@@ -1,2 +1,3 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_CLK_MT7621) += clk-mt7621.o +obj-$(CONFIG_CLK_MTMIPS) += clk-mtmips.o
drivers/clk/ralink/clk-mtmips.c new file +1115 -0
1,115 lines not on this page · raw message
Signature · 1 line
2.25.1
Sergio Paracuellos
maintainerPATCH v5 3/9 mips: ralink: rt288x: remove clock related code
In reply to Sergio ParacuellosA properly clock driver for ralink SoCs has been added. Hence there is no need to have clock related code in 'arch/mips/ralink' folder anymore.
--- arch/mips/include/asm/mach-ralink/rt288x.h | 10 ------- arch/mips/ralink/rt288x.c | 31 ---------------------- 2 files changed, 41 deletions(-)
arch/mips/include/asm/mach-ralink/rt288x.h +0 -10
@@ -18,7 +18,6 @@#define SYSC_REG_CHIP_NAME1 0x04#define SYSC_REG_CHIP_ID 0x0c#define SYSC_REG_SYSTEM_CONFIG 0x10 -#define SYSC_REG_CLKCFG 0x30#define RT2880_CHIP_NAME0 0x38325452#define RT2880_CHIP_NAME1 0x20203038
@@ -27,15 +26,6 @@#define CHIP_ID_ID_SHIFT 8#define CHIP_ID_REV_MASK 0xff -#define SYSTEM_CONFIG_CPUCLK_SHIFT 20 -#define SYSTEM_CONFIG_CPUCLK_MASK 0x3 -#define SYSTEM_CONFIG_CPUCLK_250 0x0 -#define SYSTEM_CONFIG_CPUCLK_266 0x1 -#define SYSTEM_CONFIG_CPUCLK_280 0x2 -#define SYSTEM_CONFIG_CPUCLK_300 0x3 - -#define CLKCFG_SRAM_CS_N_WDT BIT(9) -#define RT2880_SDRAM_BASE 0x08000000#define RT2880_MEM_SIZE_MIN 2#define RT2880_MEM_SIZE_MAX 128
arch/mips/ralink/rt288x.c +0 -31
@@ -21,37 +21,6 @@static struct ralink_soc_info *soc_info_ptr; -void __init ralink_clk_init (void ) -{ -unsigned long cpu_rate, wmac_rate =40000000 ; -u32 t =rt_sysc_r32 (SYSC_REG_SYSTEM_CONFIG ); - t = ((t >>SYSTEM_CONFIG_CPUCLK_SHIFT ) &SYSTEM_CONFIG_CPUCLK_MASK ); - -switch (t) { -case SYSTEM_CONFIG_CPUCLK_250 : - cpu_rate =250000000 ; -break ; -case SYSTEM_CONFIG_CPUCLK_266 : - cpu_rate =266666667 ; -break ; -case SYSTEM_CONFIG_CPUCLK_280 : - cpu_rate =280000000 ; -break ; -case SYSTEM_CONFIG_CPUCLK_300 : - cpu_rate =300000000 ; -break ; - } - -ralink_clk_add ("cpu" , cpu_rate); -ralink_clk_add ("300100.timer" , cpu_rate /2 ); -ralink_clk_add ("300120.watchdog" , cpu_rate /2 ); -ralink_clk_add ("300500.uart" , cpu_rate /2 ); -ralink_clk_add ("300900.i2c" , cpu_rate /2 ); -ralink_clk_add ("300c00.uartlite" , cpu_rate /2 ); -ralink_clk_add ("400000.ethernet" , cpu_rate /2 ); -ralink_clk_add ("480000.wmac" , wmac_rate); -} -void __init ralink_of_remap (void ) { rt_sysc_membase =plat_of_remap_node ("ralink,rt2880-sysc" );
Signature · 1 line
2.25.1
Sergio Paracuellos
maintainerPATCH v5 4/9 mips: ralink: rt305x: remove clock related code
In reply to Sergio ParacuellosA properly clock driver for ralink SoCs has been added. Hence there is no need to have clock related code in 'arch/mips/ralink' folder anymore.
--- arch/mips/include/asm/mach-ralink/rt305x.h | 21 ------ arch/mips/ralink/rt305x.c | 78 ---------------------- 2 files changed, 99 deletions(-)
arch/mips/include/asm/mach-ralink/rt305x.h +0 -21
@@ -67,26 +67,9 @@ static inline int soc_is_rt5350(void)#define CHIP_ID_ID_SHIFT 8#define CHIP_ID_REV_MASK 0xff -#define RT305X_SYSCFG_CPUCLK_SHIFT 18 -#define RT305X_SYSCFG_CPUCLK_MASK 0x1 -#define RT305X_SYSCFG_CPUCLK_LOW 0x0 -#define RT305X_SYSCFG_CPUCLK_HIGH 0x1 -#define RT305X_SYSCFG_SRAM_CS0_MODE_SHIFT 2 -#define RT305X_SYSCFG_CPUCLK_MASK 0x1#define RT305X_SYSCFG_SRAM_CS0_MODE_WDT 0x1 -#define RT3352_SYSCFG0_CPUCLK_SHIFT 8 -#define RT3352_SYSCFG0_CPUCLK_MASK 0x1 -#define RT3352_SYSCFG0_CPUCLK_LOW 0x0 -#define RT3352_SYSCFG0_CPUCLK_HIGH 0x1 - -#define RT5350_SYSCFG0_CPUCLK_SHIFT 8 -#define RT5350_SYSCFG0_CPUCLK_MASK 0x3 -#define RT5350_SYSCFG0_CPUCLK_360 0x0 -#define RT5350_SYSCFG0_CPUCLK_320 0x2 -#define RT5350_SYSCFG0_CPUCLK_300 0x3 -#define RT5350_SYSCFG0_DRAM_SIZE_SHIFT 12#define RT5350_SYSCFG0_DRAM_SIZE_MASK 7#define RT5350_SYSCFG0_DRAM_SIZE_2M 0
@@ -117,13 +100,9 @@ static inline int soc_is_rt5350(void)#define RT3352_SYSC_REG_SYSCFG0 0x010#define RT3352_SYSC_REG_SYSCFG1 0x014 -#define RT3352_SYSC_REG_CLKCFG1 0x030#define RT3352_SYSC_REG_RSTCTRL 0x034#define RT3352_SYSC_REG_USB_PS 0x05c -#define RT3352_CLKCFG0_XTAL_SEL BIT(20) -#define RT3352_CLKCFG1_UPHY0_CLK_EN BIT(18) -#define RT3352_CLKCFG1_UPHY1_CLK_EN BIT(20)#define RT3352_RSTCTRL_UHST BIT(22)#define RT3352_RSTCTRL_UDEV BIT(25)#define RT3352_SYSCFG1_USB0_HOST_MODE BIT(10)
arch/mips/ralink/rt305x.c +0 -78
84 lines not on this page · raw message
Signature · 1 line
2.25.1
Sergio Paracuellos
maintainerPATCH v5 5/9 mips: ralink: rt3883: remove clock related code
In reply to Sergio ParacuellosA properly clock driver for ralink SoCs has been added. Hence there is no need to have clock related code in 'arch/mips/ralink' folder anymore.
--- arch/mips/include/asm/mach-ralink/rt3883.h | 8 ---- arch/mips/ralink/rt3883.c | 44 ---------------------- 2 files changed, 52 deletions(-)
arch/mips/include/asm/mach-ralink/rt3883.h +0 -8
@@ -92,14 +92,6 @@#define RT3883_REVID_VER_ID_SHIFT 8#define RT3883_REVID_ECO_ID_MASK 0x0f -#define RT3883_SYSCFG0_DRAM_TYPE_DDR2 BIT(17) -#define RT3883_SYSCFG0_CPUCLK_SHIFT 8 -#define RT3883_SYSCFG0_CPUCLK_MASK 0x3 -#define RT3883_SYSCFG0_CPUCLK_250 0x0 -#define RT3883_SYSCFG0_CPUCLK_384 0x1 -#define RT3883_SYSCFG0_CPUCLK_480 0x2 -#define RT3883_SYSCFG0_CPUCLK_500 0x3 -#define RT3883_SYSCFG1_USB0_HOST_MODE BIT(10)#define RT3883_SYSCFG1_PCIE_RC_MODE BIT(8)#define RT3883_SYSCFG1_PCI_HOST_MODE BIT(7)
arch/mips/ralink/rt3883.c +0 -44
50 lines not on this page · raw message
Signature · 1 line
2.25.1
Sergio Paracuellos
maintainerPATCH v5 6/9 mips: ralink: mt7620: remove clock related code
In reply to Sergio ParacuellosA proper clock driver for ralink SoCs has been added. Hence there is no need to have clock related code in 'arch/mips/ralink' folder anymore. Since this is the last clock related code removal, remove also remaining prototypes in 'common.h' header file.
--- arch/mips/include/asm/mach-ralink/mt7620.h | 35 ---- arch/mips/ralink/common.h | 3 - arch/mips/ralink/mt7620.c | 226 --------------------- 3 files changed, 264 deletions(-)
arch/mips/include/asm/mach-ralink/mt7620.h +0 -35
@@ -20,52 +20,17 @@#define SYSC_REG_CHIP_REV 0x0c#define SYSC_REG_SYSTEM_CONFIG0 0x10#define SYSC_REG_SYSTEM_CONFIG1 0x14 -#define SYSC_REG_CLKCFG0 0x2c -#define SYSC_REG_CPU_SYS_CLKCFG 0x3c -#define SYSC_REG_CPLL_CONFIG0 0x54 -#define SYSC_REG_CPLL_CONFIG1 0x58#define MT7620_CHIP_NAME0 0x3637544d#define MT7620_CHIP_NAME1 0x20203032#define MT7628_CHIP_NAME1 0x20203832 -#define SYSCFG0_XTAL_FREQ_SEL BIT(6) -#define CHIP_REV_PKG_MASK 0x1#define CHIP_REV_PKG_SHIFT 16#define CHIP_REV_VER_MASK 0xf#define CHIP_REV_VER_SHIFT 8#define CHIP_REV_ECO_MASK 0xf -#define CLKCFG0_PERI_CLK_SEL BIT(4) - -#define CPU_SYS_CLKCFG_OCP_RATIO_SHIFT 16 -#define CPU_SYS_CLKCFG_OCP_RATIO_MASK 0xf -#define CPU_SYS_CLKCFG_OCP_RATIO_1 0/* 1:1 (Reserved) */ -#define CPU_SYS_CLKCFG_OCP_RATIO_1_5 1/* 1:1.5 (Reserved) */ -#define CPU_SYS_CLKCFG_OCP_RATIO_2 2/* 1:2 */ -#define CPU_SYS_CLKCFG_OCP_RATIO_2_5 3/* 1:2.5 (Reserved) */ -#define CPU_SYS_CLKCFG_OCP_RATIO_3 4/* 1:3 */ -#define CPU_SYS_CLKCFG_OCP_RATIO_3_5 5/* 1:3.5 (Reserved) */ -#define CPU_SYS_CLKCFG_OCP_RATIO_4 6/* 1:4 */ -#define CPU_SYS_CLKCFG_OCP_RATIO_5 7/* 1:5 */ -#define CPU_SYS_CLKCFG_OCP_RATIO_10 8/* 1:10 */ -#define CPU_SYS_CLKCFG_CPU_FDIV_SHIFT 8 -#define CPU_SYS_CLKCFG_CPU_FDIV_MASK 0x1f -#define CPU_SYS_CLKCFG_CPU_FFRAC_SHIFT 0 -#define CPU_SYS_CLKCFG_CPU_FFRAC_MASK 0x1f - -#define CPLL_CFG0_SW_CFG BIT(31) -#define CPLL_CFG0_PLL_MULT_RATIO_SHIFT 16 -#define CPLL_CFG0_PLL_MULT_RATIO_MASK 0x7 -#define CPLL_CFG0_LC_CURFCK BIT(15) -#define CPLL_CFG0_BYPASS_REF_CLK BIT(14) -#define CPLL_CFG0_PLL_DIV_RATIO_SHIFT 10 -#define CPLL_CFG0_PLL_DIV_RATIO_MASK 0x3 - -#define CPLL_CFG1_CPU_AUX1 BIT(25) -#define CPLL_CFG1_CPU_AUX0 BIT(24) -#define SYSCFG0_DRAM_TYPE_MASK 0x3#define SYSCFG0_DRAM_TYPE_SHIFT 4#define SYSCFG0_DRAM_TYPE_SDRAM 0
arch/mips/ralink/common.h +0 -3
@@ -23,9 +23,6 @@ extern struct ralink_soc_info soc_info;extern void ralink_of_remap (void ); -extern void ralink_clk_init (void ); -extern void ralink_clk_add (const char *dev,unsigned long rate); -extern void ralink_rst_init (void );extern void __init prom_soc_init (struct ralink_soc_info *soc_info);
arch/mips/ralink/mt7620.c +0 -226
238 lines not on this page · raw message
Signature · 1 line
2.25.1
Sergio Paracuellos
maintainerPATCH v5 7/9 mips: ralink: remove reset related code
In reply to Sergio ParacuellosA proper clock driver for ralink SoCs has been added. This driver is also a reset provider for the SoC. Hence there is no need to have reset related code in 'arch/mips/ralink' folder anymore. The only code that remains is the one related with mips_reboot_setup where a PCI reset is performed. We maintain this because I cannot test old ralink board with PCI to be sure all works if we remove also this code.
--- arch/mips/ralink/common.h | 2 -- arch/mips/ralink/of.c | 4 --- arch/mips/ralink/reset.c | 61 --------------------------------------- 3 files changed, 67 deletions(-)
arch/mips/ralink/common.h +0 -2
@@ -23,8 +23,6 @@ extern struct ralink_soc_info soc_info;extern void ralink_of_remap (void ); -extern void ralink_rst_init (void ); -extern void __init prom_soc_init (struct ralink_soc_info *soc_info);__iomem void *plat_of_remap_node (const char *node);
arch/mips/ralink/of.c +0 -4
@@ -81,10 +81,6 @@ static int __init plat_of_setup(void) {__dt_register_buses (soc_info.compatible,"palmbus" ); -/* make sure that the reset controller is setup early */ -if (ralink_soc !=MT762X_SOC_MT7621AT ) -ralink_rst_init (); -return 0 ; }
arch/mips/ralink/reset.c +0 -61
73 lines not on this page · raw message
Signature · 1 line
2.25.1
Sergio Paracuellos
maintainerPATCH v5 8/9 mips: ralink: get cpu rate from new driver code
In reply to Sergio ParacuellosAt very early stage on boot, there is a need to set 'mips_hpt_frequency'. This timer frequency is a half of the CPU frequency. To get clocks properly set we need to call to 'of_clk_init()' and properly get cpu clock frequency afterwards. Depending on the SoC, CPU clock index and compatible differs, so use them to get the proper clock frm the clock provider. Hence, adapt code to be aligned with new clock driver.
--- arch/mips/ralink/clk.c | 61 +++++++++++++++++++++++++++++++++++------- 1 file changed, 52 insertions(+), 9 deletions(-)
arch/mips/ralink/clk.c +52 -9
@@ -11,29 +11,72 @@#include <linux/clkdev.h> #include <linux/clk.h> #include <linux/clk-provider.h> +#include <asm/mach-ralink/ralink_regs.h> #include <asm/time.h> #include "common.h" -void ralink_clk_add (const char *dev,unsigned long rate) +static const char *clk_cpu (int *idx) { -struct clk *clk =clk_register_fixed_rate (NULL , dev,NULL ,0 , rate); - -if (!clk) -panic ("failed to add clock" ); - -clkdev_create (clk,NULL ,"%s" , dev); +switch (ralink_soc) { +case RT2880_SOC : + *idx =0 ; +return "ralink,rt2880-sysc" ; +case RT3883_SOC : + *idx =0 ; +return "ralink,rt3883-sysc" ; +case RT305X_SOC_RT3050 : + *idx =0 ; +return "ralink,rt3050-sysc" ; +case RT305X_SOC_RT3052 : + *idx =0 ; +return "ralink,rt3052-sysc" ; +case RT305X_SOC_RT3350 : + *idx =1 ; +return "ralink,rt3350-sysc" ; +case RT305X_SOC_RT3352 : + *idx =1 ; +return "ralink,rt3352-sysc" ; +case RT305X_SOC_RT5350 : + *idx =1 ; +return "ralink,rt5350-sysc" ; +case MT762X_SOC_MT7620A : + *idx =2 ; +return "ralink,mt7620-sysc" ; +case MT762X_SOC_MT7620N : + *idx =2 ; +return "ralink,mt7620-sysc" ; +case MT762X_SOC_MT7628AN : + *idx =1 ; +return "ralink,mt7628-sysc" ; +case MT762X_SOC_MT7688 : + *idx =1 ; +return "ralink,mt7688-sysc" ; +default : + *idx =-1 ; +return "invalid" ; + } }void __init plat_time_init (void ) { +struct of_phandle_args clkspec; +const char *compatible;struct clk *clk; +int cpu_clk_idx;ralink_of_remap (); -ralink_clk_init (); - clk =clk_get_sys ("cpu" ,NULL ); + compatible =clk_cpu (&cpu_clk_idx); +if (cpu_clk_idx ==-1 ) +panic ("unable to get CPU clock index" ); + +of_clk_init (NULL ); + clkspec.np =of_find_compatible_node (NULL ,NULL , compatible); + clkspec.args_count =1 ; + clkspec.args[0 ] = cpu_clk_idx; + clk =of_clk_get_from_provider (&clkspec);if (IS_ERR (clk))panic ("unable to get CPU clock, err=%ld" ,PTR_ERR (clk));pr_info ("CPU Clock: %ldMHz\n" ,clk_get_rate (clk) /1000000 );
Signature · 1 line
2.25.1
Sergio Paracuellos
maintainerPATCH v5 9/9 MAINTAINERS: add Mediatek MTMIPS Clock maintainer
In reply to Sergio ParacuellosAdding myself as maintainer for Mediatek MTMIPS clock driver.
--- MAINTAINERS | 6 ++++++ 1 file changed, 6 insertions(+)
MAINTAINERS +6 -0
@@ -13137,6 +13137,12 @@ S: Maintained F: Documentation/devicetree/bindings/phy/mediatek,mt7621-pci-phy.yaml F: drivers/phy/ralink/phy-mt7621-pci.c +MEDIATEK MTMIPS CLOCK DRIVER +M: Sergio Paracuellos <[email protected]> +S: Maintained +F: Documentation/devicetree/bindings/clock/mediatek,mtmips-sysc.yaml +F: drivers/clk/ralink/clk-mtmips.c + MEDIATEK NAND CONTROLLER DRIVER L: [email protected] S: Orphan
Signature · 1 line
2.25.1
Thomas Bogendoerfer
maintainerQuoted 162 lines · Sergio Paracuellos
Hi all!
This patchset is a big effort to properly implement a clock and reset driver for old ralink SoCs. This allow to properly define clocks in device tree and avoid to use fixed-clocks directly from '
arch/mips/ralink' architecture directory code.Device tree 'sysc' node will be both clock and reset provider using 'clock-cells' and 'reset-cells' properties.
The ralink SoCs we are taking about are RT2880, RT3050, RT3052, RT3350, RT3352, RT3883, RT5350, MT7620, MT7628 and MT7688. Mostly the code in this new driver has been extracted from '
arch/mips/ralink' and cleanly put using kernel clock and reset driver APIs. The clock plans for this SoCs only talks about relation between CPU frequency and BUS frequency. This relation is different depending on the particular SoC. CPU clock is derived from XTAL frequencies.Depending on the SoC we have the following frequencies:
* RT2880 SoC:
- XTAL: 40 MHz.
- CPU: 250, 266, 280 or 300 MHz.
- BUS: CPU / 2 MHz.
* RT3050, RT3052, RT3350:
- XTAL: 40 MHz.
- CPU: 320 or 384 MHz.
- BUS: CPU / 3 MHz.
* RT3352:
- XTAL: 40 MHz.
- CPU: 384 or 400 MHz.
- BUS: CPU / 3 MHz.
- PERIPH: 40 MHz.
* RT3383:
- XTAL: 40 MHz.
- CPU: 250, 384, 480 or 500 MHz.
- BUS: Depends on RAM Type and CPU:
+ RAM DDR2: 125. ELSE 83 MHz.
+ RAM DDR2: 128. ELSE 96 MHz.
+ RAM DDR2: 160. ELSE 120 MHz.
+ RAM DDR2: 166. ELSE 125 MHz.
* RT5350:
- XTAL: 40 MHz.
- CPU: 300, 320 or 360 MHz.
- BUS: CPU / 3, CPU / 4, CPU / 3 MHz.
- PERIPH: 40 MHz.
* MT7628 and MT7688:
- XTAL: 20 MHz or 40 MHz.
- CPU: 575 or 580 MHz.
- BUS: CPU / 3.
- PCMI2S: 480 MHz.
- PERIPH: 40 MHz.
* MT7620:
- XTAL: 20 MHz or 40 MHz.
- PLL: XTAL, 480, 600 MHz.
- CPU: depends on PLL and some mult and dividers.
- BUS: depends on PLL and some mult and dividers.
- PERIPH: 40 or XTAL MHz.MT7620 is a bit more complex deriving CPU clock from a PLL and an bunch of register reads and predividers. To derive CPU and BUS frequencies in the MT7620 SoC '
mt7620_calc_rate()' helper is used.
In the case XTAL can have different frequencies and we need a different clock frequency for peripherals 'periph' clock in introduced. The rest of the peripherals present in the SoC just follow their parent frequencies.I am using 'mtmips' inside for ralink clock driver. This is aligned with pinctrl series recently merged through pinctrl git tree [0].
I am maintaining ralink as prefix for compatible strings after discussions between Rob and Arinc in v2 of this series [1].
Changes have been compile tested for:
- RT2880
- RT3883Changes have been properly tested in:
- RT5350 SoC based board (ALL5003 board)
- MT7620A SoC based board (Haier HW-L1W)
- MT7628AN SoC based board (Motorola MWR03)All of them resulting in a working platform.
Dts files for these SoCs in-tree except MT7621 are incomplete. We are planning to align with openWRT files at some point and add extra needed changes. Hence I am not touching them at all in these series. If this is a problem, please let me know and I will update them.
Talking about merging this series I'd like all of the patches going through the MIPS tree if possible.
Thanks in advance for your time.
Best regards,
Sergio ParacuellosChanges in v5:
- Address comments of Shiji Yang in v4.
- Make use 'of_find_compatible_node()' instead of 'of_find_node_by_name()' since node names must not be an ABI (Thanks Krzysztof!!!)
- Test this changes in mt7620a Soc based board and MT7628AN Soc based board (Thanks Shiji Yang!!!)Changes in v4:
- Collect Reviewed-by and Acked-by tags.
- Pass proper data for 'ralink,rt3352-sysc' and 'ralink,rt3883-sysc' compatible string.Changes in v3:
- Address Stephen comments in v2:
+ Drop unsused include '<linux/clk.h>'.
+ Add fixed and factor clocks when it makes sense.
+ Make 'mtmips_periph_clk_ops' named variable.
+WARN_ON->WARN_ON_ONCE.
+ AvoidCONFIG_USBdependent code. Introduce new 'mtmips_clk_regs_init'.
+ Don't validate the bindings in the driver.
+ Make const 'structclk_init_data' used inside macros.
+do_div->div_u64.
+ Make use ofdev_err_probe.Changes in v2:
- Address bindings documentation changes pointed out by Krzysztof:
+ Rename the file into 'mediatek,mtmips-sysc.yaml'.
+ Redo commit subject and log message.
+ Order compatibles alphabetically.
+ Redo bindings description taking into account this is a system controller node which provides both clocks and resets to the world.
+ Drop label from example.
+ Use 'syscon' as node name in example.
+ Drop no sense 'ralink,rt2880-reset' compatible string
- Squash patches 6 and 7 together as pointed out by Stephen Boyd.Previoous series:
v4: https://lore.kernel.org/linux-clk/[email protected]/T/#t
v3: https://lore.kernel.org/linux-mips/[email protected]/T/#mafbc1704938b94a367c4b6240d9880a67be1f92f
v2: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#t
v1: https://lore.kernel.org/linux-clk/[email protected]/T/#t[0]: https://lore.kernel.org/linux-gpio/[email protected]/T/#t
[1]: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#mfe725b6e3382c6fb09736472a846cbbc84f264dcSergio Paracuellos (9):
dt-bindings: clock: add mtmips SoCs system controller
clk: ralink: add clock and reset driver for MTMIPS SoCs
mips: ralink: rt288x: remove clock related code
mips: ralink: rt305x: remove clock related code
mips: ralink: rt3883: remove clock related code
mips: ralink: mt7620: remove clock related code
mips: ralink: remove reset related code
mips: ralink: get cpu rate from new driver code
MAINTAINERS: add Mediatek MTMIPS Clock maintainer.../bindings/clock/mediatek,mtmips-sysc.yaml | 64 + MAINTAINERS | 6 + arch/mips/include/asm/mach-ralink/mt7620.h | 35 - arch/mips/include/asm/mach-ralink/rt288x.h | 10 - arch/mips/include/asm/mach-ralink/rt305x.h | 21 - arch/mips/include/asm/mach-ralink/rt3883.h | 8 - arch/mips/ralink/clk.c | 61 +- arch/mips/ralink/common.h | 5 - arch/mips/ralink/mt7620.c | 226 ---- arch/mips/ralink/of.c | 4 - arch/mips/ralink/reset.c | 61 - arch/mips/ralink/rt288x.c | 31 -
Quoted 8 lines
arch/mips/ralink/rt305x.c | 78 -- arch/mips/ralink/rt3883.c | 44 - drivers/clk/ralink/Kconfig | 7 + drivers/clk/ralink/Makefile | 1 + drivers/clk/ralink/clk-mtmips.c | 1115 +++++++++++++++++ 17 files changed, 1245 insertions(+), 532 deletions(-) create mode 100644 Documentation/devicetree/bindings/clock/mediatek,mtmips-sysc.yaml create mode 100644 drivers/clk/ralink/clk-mtmips.c
series applied to mips-next.
Thomas.
Signature · 2 lines
Crap can work. Given enough thrust pigs will fly, but it's not necessarily a good idea. [ RFC1925, 2.3 ]