Skip to contentSkip to conversation

6.3.11-rc1 review

PATCH In review Greg Kroah-Hartman 3 participants 36 messages Jun 29, 2023 – Jul 3, 2023 Stable branch

lore
Share & tools
lore

Greg Kroah-Hartman

author maintainer
#0 lore raw

cover 6.3.11-rc1 review

This is the start of the stable review cycle for the 6.3.11 release. There are 29 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sat, 01 Jul 2023 18:41:39 +0000. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

	https://www.kernel.org/pub/linux/kernel/v6.x/stable-review/patch-6.3.11-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-6.3.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <[email protected]>

    Linux 6.3.11-rc1

Ricardo Cañuelo <[email protected]>
Revert "thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in mtk_thermal_probe"

Mike Hommey <[email protected]>
HID: logitech-hidpp: add HIDPP_QUIRK_DELAYED_INIT for the T651.

Jason Gerecke <[email protected]>
HID: wacom: Use ktime_t rather than int when dealing with timestamps

Ludvig Michaelsson <[email protected]>
HID: hidraw: fix data race on device refcount

Zhang Shurong <[email protected]>
fbdev: fix potential OOB read in fast_imageblit()

Linus Torvalds <[email protected]>
gup: add warning if some caller would seem to want stack expansion

Linus Torvalds <[email protected]>
mm: always expand the stack with the mmap write lock held

Linus Torvalds <[email protected]>
execve: expand new process stack manually ahead of time

Liam R. Howlett <[email protected]>
mm: make find_extend_vma() fail if write lock not held

Linus Torvalds <[email protected]>
powerpc/mm: convert coprocessor fault to lock_mm_and_find_vma()

Linus Torvalds <[email protected]>
mm/fault: convert remaining simple cases to lock_mm_and_find_vma()

Ben Hutchings <[email protected]>
arm/mm: Convert to using lock_mm_and_find_vma()

Ben Hutchings <[email protected]>
riscv/mm: Convert to using lock_mm_and_find_vma()

Ben Hutchings <[email protected]>
mips/mm: Convert to using lock_mm_and_find_vma()

Michael Ellerman <[email protected]>
powerpc/mm: Convert to using lock_mm_and_find_vma()

Linus Torvalds <[email protected]>
arm64/mm: Convert to using lock_mm_and_find_vma()

Linus Torvalds <[email protected]>
mm: make the page fault mmap locking killable

Linus Torvalds <[email protected]>
mm: introduce new 'lock_mm_and_find_vma()' page fault helper

Peng Zhang <[email protected]>
maple_tree: fix potential out-of-bounds access in mas_wr_end_piv()

Oliver Hartkopp <[email protected]>
can: isotp: isotp_sendmsg(): fix return error fix on TX path

Wyes Karny <[email protected]>
cpufreq: amd-pstate: Make amd-pstate EPP driver name hyphenated

Thomas Gleixner <[email protected]>
x86/smp: Cure kexec() vs. mwait_play_dead() breakage

Thomas Gleixner <[email protected]>
x86/smp: Use dedicated cache-line for mwait_play_dead()

Thomas Gleixner <[email protected]>
x86/smp: Remove pointless wmb()s from native_stop_other_cpus()

Tony Battersby <[email protected]>
x86/smp: Dont access non-existing CPUID leaf

Thomas Gleixner <[email protected]>
x86/smp: Make stop_other_cpus() more robust

Borislav Petkov (AMD) <[email protected]>
x86/microcode/AMD: Load late on both threads too

David Woodhouse <[email protected]>
mm/mmap: Fix error return in do_vmi_align_munmap()

Liam R. Howlett <[email protected]>
mm/mmap: Fix error path in do_vmi_align_munmap()

-------------

Diffstat:

 Makefile                                  |   4 +-
 arch/alpha/Kconfig                        |   1 +
 arch/alpha/mm/fault.c                     |  13 +--
 arch/arc/Kconfig                          |   1 +
 arch/arc/mm/fault.c                       |  11 +--
 arch/arm/Kconfig                          |   1 +
 arch/arm/mm/fault.c                       |  63 +++---------
 arch/arm64/Kconfig                        |   1 +
 arch/arm64/mm/fault.c                     |  44 ++-------
 arch/csky/Kconfig                         |   1 +
 arch/csky/mm/fault.c                      |  22 +----
 arch/hexagon/Kconfig                      |   1 +
 arch/hexagon/mm/vm_fault.c                |  18 +---
 arch/ia64/mm/fault.c                      |  36 ++-----
 arch/loongarch/Kconfig                    |   1 +
 arch/loongarch/mm/fault.c                 |  16 ++--
 arch/m68k/mm/fault.c                      |   9 +-
 arch/microblaze/mm/fault.c                |   5 +-
 arch/mips/Kconfig                         |   1 +
 arch/mips/mm/fault.c                      |  12 +--
 arch/nios2/Kconfig                        |   1 +
 arch/nios2/mm/fault.c                     |  17 +---
 arch/openrisc/mm/fault.c                  |   5 +-
 arch/parisc/mm/fault.c                    |  23 +++--
 arch/powerpc/Kconfig                      |   1 +
 arch/powerpc/mm/copro_fault.c             |  14 +--
 arch/powerpc/mm/fault.c                   |  39 +-------
 arch/riscv/Kconfig                        |   1 +
 arch/riscv/mm/fault.c                     |  31 +++---
 arch/s390/mm/fault.c                      |   5 +-
 arch/sh/Kconfig                           |   1 +
 arch/sh/mm/fault.c                        |  17 +---
 arch/sparc/Kconfig                        |   1 +
 arch/sparc/mm/fault_32.c                  |  32 ++-----
 arch/sparc/mm/fault_64.c                  |   8 +-
 arch/um/kernel/trap.c                     |  11 ++-
 arch/x86/Kconfig                          |   1 +
 arch/x86/include/asm/cpu.h                |   2 +
 arch/x86/include/asm/smp.h                |   2 +
 arch/x86/kernel/cpu/microcode/amd.c       |   2 +-
 arch/x86/kernel/process.c                 |  28 +++++-
 arch/x86/kernel/smp.c                     |  73 ++++++++------
 arch/x86/kernel/smpboot.c                 |  81 ++++++++++++++--
 arch/x86/mm/fault.c                       |  52 +---------
 arch/xtensa/Kconfig                       |   1 +
 arch/xtensa/mm/fault.c                    |  14 +--
 drivers/cpufreq/amd-pstate.c              |   2 +-
 drivers/hid/hid-logitech-hidpp.c          |   2 +-
 drivers/hid/hidraw.c                      |   9 +-
 drivers/hid/wacom_wac.c                   |   6 +-
 drivers/hid/wacom_wac.h                   |   2 +-
 drivers/iommu/amd/iommu_v2.c              |   4 +-
 drivers/iommu/iommu-sva.c                 |   2 +-
 drivers/thermal/mediatek/auxadc_thermal.c |  14 +--
 drivers/video/fbdev/core/sysimgblt.c      |   2 +-
 fs/binfmt_elf.c                           |   6 +-
 fs/exec.c                                 |  38 ++++----
 include/linux/mm.h                        |  16 ++--
 lib/maple_tree.c                          |  11 ++-
 mm/Kconfig                                |   4 +
 mm/gup.c                                  |  14 ++-
 mm/memory.c                               | 127 +++++++++++++++++++++++++
 mm/mmap.c                                 | 153 +++++++++++++++++++++++-------
 mm/nommu.c                                |  17 ++--
 net/can/isotp.c                           |   5 +-
 65 files changed, 614 insertions(+), 544 deletions(-)
author maintainer
#1 lore raw

PATCH 1/29 mm/mmap: Fix error path in do_vmi_align_munmap()

From: "Liam R. Howlett" <[email protected]>

commit 606c812eb1d5b5fb0dd9e330ca94b52d7c227830 upstream.

The error unrolling was leaving the VMAs detached in many cases and leaving the locked_vm statistic altered, and skipping the unrolling entirely in the case of the vma tree write failing.

Fix the error path by re-attaching the detached VMAs and adding the necessary goto for the failed vma tree write, and fix the locked_vm statistic by only updating after the vma tree write succeeds.

Fixes 763ecb035029 ("mm: remove the vma linked list")

[ dwmw2: Strictly, the original patch wasn't *re-attaching* the
detached VMAs. They *were* still attached but just had the 'detached' flag set, which is an optimisation. Which doesn't exist in 6.3, so drop that. Also drop the call to vma_start_write() which came in with the per-VMA locking in 6.4. ]

---
 mm/mmap.c |   29 +++++++++++------------------
 1 file changed, 11 insertions(+), 18 deletions(-)
mm/mmap.c +11 -18
@@ -2280,19 +2280,6 @@ int split_vma(struct vma_iterator *vmi,
 	return __split_vma(vmi, vma, addr, new_below);
 }
 
-static inline int munmap_sidetree(struct vm_area_struct *vma,
-				   struct ma_state *mas_detach)
-{
-	mas_set_range(mas_detach, vma->vm_start, vma->vm_end - 1);
-	if (mas_store_gfp(mas_detach, vma, GFP_KERNEL))
-		return -ENOMEM;
-
-	if (vma->vm_flags & VM_LOCKED)
-		vma->vm_mm->locked_vm -= vma_pages(vma);
-
-	return 0;
-}
-
 /*
  * do_vmi_align_munmap() - munmap the aligned region from @start to @end.
  * @vmi: The vma iterator
@@ -2314,6 +2301,7 @@ do_vmi_align_munmap(struct vma_iterator
 	struct maple_tree mt_detach;
 	int count = 0;
 	int error = -ENOMEM;
+	unsigned long locked_vm = 0;
 	MA_STATE(mas_detach, &mt_detach, 0, 0);
 	mt_init_flags(&mt_detach, vmi->mas.tree->ma_flags & MT_FLAGS_LOCK_MASK);
 	mt_set_external_lock(&mt_detach, &mm->mmap_lock);
@@ -2359,9 +2347,11 @@ do_vmi_align_munmap(struct vma_iterator
 			if (error)
 				goto end_split_failed;
 		}
-		error = munmap_sidetree(next, &mas_detach);
-		if (error)
-			goto munmap_sidetree_failed;
+		mas_set_range(&mas_detach, next->vm_start, next->vm_end - 1);
+		if (mas_store_gfp(&mas_detach, next, GFP_KERNEL))
+			goto munmap_gather_failed;
+		if (next->vm_flags & VM_LOCKED)
+			locked_vm += vma_pages(next);
 
 		count++;
 #ifdef CONFIG_DEBUG_VM_MAPLE_TREE
@@ -2407,10 +2397,12 @@ do_vmi_align_munmap(struct vma_iterator
 	}
 #endif
 	/* Point of no return */
+	error = -ENOMEM;
 	vma_iter_set(vmi, start);
 	if (vma_iter_clear_gfp(vmi, start, end, GFP_KERNEL))
-		return -ENOMEM;
+		goto clear_tree_failed;
 
+	mm->locked_vm -= locked_vm;
 	mm->map_count -= count;
 	/*
 	 * Do not downgrade mmap_lock if we are next to VM_GROWSDOWN or
@@ -2440,8 +2432,9 @@ do_vmi_align_munmap(struct vma_iterator
 	validate_mm(mm);
 	return downgrade ? 1 : 0;
 
+clear_tree_failed:
 userfaultfd_error:
-munmap_sidetree_failed:
+munmap_gather_failed:
 end_split_failed:
 	__mt_destroy(&mt_detach);
 start_split_failed:
author maintainer
#2 lore raw

PATCH 2/29 mm/mmap: Fix error return in do_vmi_align_munmap()

In reply to Greg Kroah-Hartman

From: David Woodhouse <[email protected]>

commit 6c26bd4384da24841bac4f067741bbca18b0fb74 upstream,

If mas_store_gfp() in the gather loop failed, the 'error' variable that ultimately gets returned was not being set. In many cases, its original value of -ENOMEM was still in place, and that was fine. But if VMAs had been split at the start or end of the range, then 'error' could be zero.

Change to the 'error = foo(); if (error) goto …' idiom to fix the bug.

Also clean up a later case which avoided the same bug by *explicitly* setting error = -ENOMEM right before calling the function that might return -ENOMEM.

In a final cosmetic change, move the 'Point of no return' comment to *after* the goto. That's been in the wrong place since the preallocation was removed, and this new error path was added.

Fixes 606c812eb1d5 ("mm/mmap: Fix error path in do_vmi_align_munmap()")
---
 mm/mmap.c |    9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)
mm/mmap.c +5 -4
@@ -2348,7 +2348,8 @@ do_vmi_align_munmap(struct vma_iterator
 				goto end_split_failed;
 		}
 		mas_set_range(&mas_detach, next->vm_start, next->vm_end - 1);
-		if (mas_store_gfp(&mas_detach, next, GFP_KERNEL))
+		error = mas_store_gfp(&mas_detach, next, GFP_KERNEL);
+		if (error)
 			goto munmap_gather_failed;
 		if (next->vm_flags & VM_LOCKED)
 			locked_vm += vma_pages(next);
@@ -2396,12 +2397,12 @@ do_vmi_align_munmap(struct vma_iterator
 		BUG_ON(count != test_count);
 	}
 #endif
-	/* Point of no return */
-	error = -ENOMEM;
 	vma_iter_set(vmi, start);
-	if (vma_iter_clear_gfp(vmi, start, end, GFP_KERNEL))
+	error = vma_iter_clear_gfp(vmi, start, end, GFP_KERNEL);
+	if (error)
 		goto clear_tree_failed;
 
+	/* Point of no return */
 	mm->locked_vm -= locked_vm;
 	mm->map_count -= count;
 	/*
#3 lore raw

Re: [PATCH 6.3 02/29] mm/mmap: Fix error return in do_vmi_align_munmap()

Quoted 10 lines · Greg Kroah-Hartman

From: David Woodhouse <[email protected]>

commit 6c26bd4384da24841bac4f067741bbca18b0fb74 upstream,

If mas_store_gfp() in the gather loop failed, the 'error' variable that ultimately gets returned was not being set. In many cases, its original value of -ENOMEM was still in place, and that was fine. But if VMAs had been split at the start or end of the range, then 'error' could be zero.

Change to the 'error = foo(); if (error) goto …' idiom to fix the bug.

Quoted 1 line · that isn't what the original commit message said. It

Change to the 'error = foo(); if (error) goto …' idiom to fix the bug.

This far into the 21st century, we don't see a lot of tools injecting Mojibake any more; the mantra of "everything is UTF-8, all of the time" mostly seems to work.

Granted, there are more important problems in the world, but it'd be good to identify where that happened and file bugs if needed.

author maintainer
#4 lore raw

Re: [PATCH 6.3 02/29] mm/mmap: Fix error return in do_vmi_align_munmap()

Quoted 14 lines · David Woodhouse
Quoted 10 lines · Greg Kroah-Hartman

From: David Woodhouse <[email protected]>

commit 6c26bd4384da24841bac4f067741bbca18b0fb74 upstream,

If mas_store_gfp() in the gather loop failed, the 'error' variable that ultimately gets returned was not being set. In many cases, its original value of -ENOMEM was still in place, and that was fine. But if VMAs had been split at the start or end of the range, then 'error' could be zero.

Change to the 'error = foo(); if (error) goto …' idiom to fix the bug.

Hrm, that isn't what the original commit message said. It said:

Quoted 8 lines
Quoted 1 line

Change to the 'error = foo(); if (error) goto …' idiom to fix the bug.

This far into the 21st century, we don't see a lot of tools injecting Mojibake any more; the mantra of "everything is UTF-8, all of the time" mostly seems to work.

Granted, there are more important problems in the world, but it'd be good to identify where that happened and file bugs if needed.

This is probably due to me going from 'git format-patch' to 'quit import' and then to 'git am' as part of the workflow I use here. I'll try to narrow it down as to where this went wrong...

thanks,

greg k-h

author maintainer
#5 lore raw

PATCH 3/29 x86/microcode/AMD: Load late on both threads too

In reply to Greg Kroah-Hartman

From: Borislav Petkov (AMD) <[email protected]>

commit a32b0f0db3f396f1c9be2fe621e77c09ec3d8e7d upstream.

Do the same as early loading - load on both threads.

---
 arch/x86/kernel/cpu/microcode/amd.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/x86/kernel/cpu/microcode/amd.c +1 -1
@@ -705,7 +705,7 @@ static enum ucode_state apply_microcode_
 	rdmsr(MSR_AMD64_PATCH_LEVEL, rev, dummy);
 
 	/* need to apply patch? */
-	if (rev >= mc_amd->hdr.patch_id) {
+	if (rev > mc_amd->hdr.patch_id) {
 		ret = UCODE_OK;
 		goto out;
 	}
author maintainer
#6 lore raw

PATCH 4/29 x86/smp: Make stop_other_cpus() more robust

In reply to Greg Kroah-Hartman

From: Thomas Gleixner <[email protected]>

commit 1f5e7eb7868e42227ac426c96d437117e6e06e8e upstream.

Tony reported intermittent lockups on poweroff. His analysis identified the wbinvd() in stop_this_cpu() as the culprit. This was added to ensure that on SME enabled machines a kexec() does not leave any stale data in the caches when switching from encrypted to non-encrypted mode or vice versa.

That wbinvd() is conditional on the SME feature bit which is read directly from CPUID. But that readout does not check whether the CPUID leaf is available or not. If it's not available the CPU will return the value of the highest supported leaf instead. Depending on the content the "SME" bit might be set or not.

That's incorrect but harmless. Making the CPUID readout conditional makes the observed hangs go away, but it does not fix the underlying problem:

CPU0 CPU1

stop_other_cpus()
send_IPIs(REBOOT); stop_this_cpu()
while (num_online_cpus() > 1); set_online(false);
proceed... -> hang
wbinvd()

WBINVD is an expensive operation and if multiple CPUs issue it at the same time the resulting delays are even larger.

But CPU0 already observed num_online_cpus() going down to 1 and proceeds which causes the system to hang.

This issue exists independent of WBINVD, but the delays caused by WBINVD make it more prominent.

Make this more robust by adding a cpumask which is initialized to the online CPU mask before sending the IPIs and CPUs clear their bit in stop_this_cpu() after the WBINVD completed. Check for that cpumask to become empty in stop_other_cpus() instead of watching num_online_cpus().

The cpumask cannot plug all holes either, but it's better than a raw counter and allows to restrict the NMI fallback IPI to be sent only the CPUs which have not reported within the timeout window.

---
 arch/x86/include/asm/cpu.h |    2 +
 arch/x86/kernel/process.c  |   23 +++++++++++++++-
 arch/x86/kernel/smp.c      |   62 +++++++++++++++++++++++++++++----------------
 3 files changed, 64 insertions(+), 23 deletions(-)
arch/x86/include/asm/cpu.h +2 -0
@@ -98,4 +98,6 @@ extern u64 x86_read_arch_cap_msr(void);
 int intel_find_matching_signature(void *mc, unsigned int csig, int cpf);
 int intel_microcode_sanity_check(void *mc, bool print_err, int hdr_type);
 
+extern struct cpumask cpus_stop_mask;
+
 #endif /* _ASM_X86_CPU_H */
arch/x86/kernel/process.c +21 -2
@@ -752,13 +752,23 @@ bool xen_set_default_idle(void)
 }
 #endif
 
+struct cpumask cpus_stop_mask;
+
 void __noreturn stop_this_cpu(void *dummy)
 {
+	unsigned int cpu = smp_processor_id();
+
 	local_irq_disable();
+
 	/*
-	 * Remove this CPU:
+	 * Remove this CPU from the online mask and disable it
+	 * unconditionally. This might be redundant in case that the reboot
+	 * vector was handled late and stop_other_cpus() sent an NMI.
+	 *
+	 * According to SDM and APM NMIs can be accepted even after soft
+	 * disabling the local APIC.
 	 */
-	set_cpu_online(smp_processor_id(), false);
+	set_cpu_online(cpu, false);
 	disable_local_APIC();
 	mcheck_cpu_clear(this_cpu_ptr(&cpu_info));
 
@@ -776,6 +786,15 @@ void __noreturn stop_this_cpu(void *dumm
 	 */
 	if (cpuid_eax(0x8000001f) & BIT(0))
 		native_wbinvd();
+
+	/*
+	 * This brings a cache line back and dirties it, but
+	 * native_stop_other_cpus() will overwrite cpus_stop_mask after it
+	 * observed that all CPUs reported stop. This write will invalidate
+	 * the related cache line on this CPU.
+	 */
+	cpumask_clear_cpu(cpu, &cpus_stop_mask);
+
 	for (;;) {
 		/*
 		 * Use native_halt() so that memory contents don't change
arch/x86/kernel/smp.c +41 -21

110 lines not on this page · raw message

author maintainer
#7 lore raw

PATCH 5/29 x86/smp: Dont access non-existing CPUID leaf

In reply to Greg Kroah-Hartman

From: Tony Battersby <[email protected]>

commit 9b040453d4440659f33dc6f0aa26af418ebfe70b upstream.

stop_this_cpu() tests CPUID leaf 0x8000001f::EAX unconditionally. Intel CPUs return the content of the highest supported leaf when a non-existing leaf is read, while AMD CPUs return all zeros for unsupported leafs.

So the result of the test on Intel CPUs is lottery.

While harmless it's incorrect and causes the conditional wbinvd() to be issued where not required.

Check whether the leaf is supported before reading it.

[ tglx: Adjusted changelog ]

---
 arch/x86/kernel/process.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
arch/x86/kernel/process.c +3 -2
@@ -756,6 +756,7 @@ struct cpumask cpus_stop_mask;
 
 void __noreturn stop_this_cpu(void *dummy)
 {
+	struct cpuinfo_x86 *c = this_cpu_ptr(&cpu_info);
 	unsigned int cpu = smp_processor_id();
 
 	local_irq_disable();
@@ -770,7 +771,7 @@ void __noreturn stop_this_cpu(void *dumm
 	 */
 	set_cpu_online(cpu, false);
 	disable_local_APIC();
-	mcheck_cpu_clear(this_cpu_ptr(&cpu_info));
+	mcheck_cpu_clear(c);
 
 	/*
 	 * Use wbinvd on processors that support SME. This provides support
@@ -784,7 +785,7 @@ void __noreturn stop_this_cpu(void *dumm
 	 * Test the CPUID bit directly because the machine might've cleared
 	 * X86_FEATURE_SME due to cmdline options.
 	 */
-	if (cpuid_eax(0x8000001f) & BIT(0))
+	if (c->extended_cpuid_level >= 0x8000001f && (cpuid_eax(0x8000001f) & BIT(0)))
 		native_wbinvd();
 
 	/*
author maintainer
#8 lore raw

PATCH 6/29 x86/smp: Remove pointless wmb()s from native_stop_other_cpus()

In reply to Greg Kroah-Hartman

From: Thomas Gleixner <[email protected]>

commit 2affa6d6db28855e6340b060b809c23477aa546e upstream.

The wmb()s before sending the IPIs are not synchronizing anything.

If at all then the apic IPI functions have to provide or act as appropriate barriers.

Remove these cargo cult barriers which have no explanation of what they are synchronizing.

---
 arch/x86/kernel/smp.c |    6 ------
 1 file changed, 6 deletions(-)
arch/x86/kernel/smp.c +0 -6
@@ -184,9 +184,6 @@ static void native_stop_other_cpus(int w
 	cpumask_clear_cpu(cpu, &cpus_stop_mask);
 
 	if (!cpumask_empty(&cpus_stop_mask)) {
-		/* sync above data before sending IRQ */
-		wmb();
-
 		apic_send_IPI_allbutself(REBOOT_VECTOR);
 
 		/*
@@ -208,9 +205,6 @@ static void native_stop_other_cpus(int w
 		 * CPUs to stop.
 		 */
 		if (!smp_no_nmi_ipi && !register_stop_handler()) {
-			/* Sync above data before sending IRQ */
-			wmb();
-
 			pr_emerg("Shutting down cpus with NMI\n");
 
 			for_each_cpu(cpu, &cpus_stop_mask)
author maintainer
#9 lore raw

PATCH 7/29 x86/smp: Use dedicated cache-line for mwait_play_dead()

In reply to Greg Kroah-Hartman

From: Thomas Gleixner <[email protected]>

commit f9c9987bf52f4e42e940ae217333ebb5a4c3b506 upstream.

Monitoring idletask::thread_info::flags in mwait_play_dead() has been an obvious choice as all what is needed is a cache line which is not written by other CPUs.

But there is a use case where a "dead" CPU needs to be brought out of
MWAIT: kexec().

This is required as kexec() can overwrite text, pagetables, stacks and the monitored cacheline of the original kernel. The latter causes MWAIT to resume execution which obviously causes havoc on the kexec kernel which results usually in triple faults.

Use a dedicated per CPU storage to prepare for that.

---
 arch/x86/kernel/smpboot.c |   24 ++++++++++++++----------
 1 file changed, 14 insertions(+), 10 deletions(-)
arch/x86/kernel/smpboot.c +14 -10
@@ -101,6 +101,17 @@ EXPORT_PER_CPU_SYMBOL(cpu_die_map);
 DEFINE_PER_CPU_READ_MOSTLY(struct cpuinfo_x86, cpu_info);
 EXPORT_PER_CPU_SYMBOL(cpu_info);
 
+struct mwait_cpu_dead {
+	unsigned int	control;
+	unsigned int	status;
+};
+
+/*
+ * Cache line aligned data for mwait_play_dead(). Separate on purpose so
+ * that it's unlikely to be touched by other CPUs.
+ */
+static DEFINE_PER_CPU_ALIGNED(struct mwait_cpu_dead, mwait_cpu_dead);
+
 /* Logical package management. We might want to allocate that dynamically */
 unsigned int __max_logical_packages __read_mostly;
 EXPORT_SYMBOL(__max_logical_packages);
@@ -1750,10 +1761,10 @@ EXPORT_SYMBOL_GPL(cond_wakeup_cpu0);
  */
 static inline void mwait_play_dead(void)
 {
+	struct mwait_cpu_dead *md = this_cpu_ptr(&mwait_cpu_dead);
 	unsigned int eax, ebx, ecx, edx;
 	unsigned int highest_cstate = 0;
 	unsigned int highest_subcstate = 0;
-	void *mwait_ptr;
 	int i;
 
 	if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD ||
@@ -1788,13 +1799,6 @@ static inline void mwait_play_dead(void)
 			(highest_subcstate - 1);
 	}
 
-	/*
-	 * This should be a memory location in a cache line which is
-	 * unlikely to be touched by other processors.  The actual
-	 * content is immaterial as it is not actually modified in any way.
-	 */
-	mwait_ptr = &current_thread_info()->flags;
-
 	wbinvd();
 
 	while (1) {
@@ -1806,9 +1810,9 @@ static inline void mwait_play_dead(void)
 		 * case where we return around the loop.
 		 */
 		mb();
-		clflush(mwait_ptr);
+		clflush(md);
 		mb();
-		__monitor(mwait_ptr, 0, 0);
+		__monitor(md, 0, 0);
 		mb();
 		__mwait(eax, 0);
 
author maintainer
#10 lore raw

PATCH 8/29 x86/smp: Cure kexec() vs. mwait_play_dead() breakage

In reply to Greg Kroah-Hartman

From: Thomas Gleixner <[email protected]>

commit d7893093a7417527c0d73c9832244e65c9d0114f upstream.

TLDR: It's a mess.

When kexec() is executed on a system with offline CPUs, which are parked in mwait_play_dead() it can end up in a triple fault during the bootup of the kexec kernel or cause hard to diagnose data corruption.

The reason is that kexec() eventually overwrites the previous kernel's text, page tables, data and stack. If it writes to the cache line which is monitored by a previously offlined CPU, MWAIT resumes execution and ends up executing the wrong text, dereferencing overwritten page tables or corrupting the kexec kernels data.

Cure this by bringing the offlined CPUs out of MWAIT into HLT.

Write to the monitored cache line of each offline CPU, which makes MWAIT resume execution. The written control word tells the offlined CPUs to issue HLT, which does not have the MWAIT problem.

That does not help, if a stray NMI, MCE or SMI hits the offlined CPUs as those make it come out of HLT.

A follow up change will put them into INIT, which protects at least against NMI and SMI.

Fixes ea53069231f9 ("x86, hotplug: Use mwait to offline a processor, fix the legacy case")
---
 arch/x86/include/asm/smp.h |    2 +
 arch/x86/kernel/smp.c      |    5 +++
 arch/x86/kernel/smpboot.c  |   59 +++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 66 insertions(+)
arch/x86/include/asm/smp.h +2 -0
@@ -131,6 +131,8 @@ void wbinvd_on_cpu(int cpu);
 int wbinvd_on_all_cpus(void);
 void cond_wakeup_cpu0(void);
 
+void smp_kick_mwait_play_dead(void);
+
 void native_smp_send_reschedule(int cpu);
 void native_send_call_func_ipi(const struct cpumask *mask);
 void native_send_call_func_single_ipi(int cpu);
arch/x86/kernel/smp.c +5 -0
@@ -21,6 +21,7 @@
 #include <linux/interrupt.h>
 #include <linux/cpu.h>
 #include <linux/gfp.h>
+#include <linux/kexec.h>
 
 #include <asm/mtrr.h>
 #include <asm/tlbflush.h>
@@ -157,6 +158,10 @@ static void native_stop_other_cpus(int w
 	if (atomic_cmpxchg(&stopping_cpu, -1, cpu) != -1)
 		return;
 
+	/* For kexec, ensure that offline CPUs are out of MWAIT and in HLT */
+	if (kexec_in_progress)
+		smp_kick_mwait_play_dead();
+
 	/*
 	 * 1) Send an IPI on the reboot vector to all other CPUs.
 	 *
arch/x86/kernel/smpboot.c +59 -0

93 lines not on this page · raw message

author maintainer
#11 lore raw

PATCH 9/29 cpufreq: amd-pstate: Make amd-pstate EPP driver name hyphenated

In reply to Greg Kroah-Hartman

From: Wyes Karny <[email protected]>

commit f4aad639302a07454dcb23b408dcadf8a9efb031 upstream.

amd-pstate passive mode driver is hyphenated. So make amd-pstate active mode driver consistent with that rename "amd_pstate_epp" to "amd-pstate-epp".

Fixes ffa5096a7c33 ("cpufreq: amd-pstate: implement Pstate EPP support for the AMD processors")
Cc All applicable <[email protected]>
---
 drivers/cpufreq/amd-pstate.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/cpufreq/amd-pstate.c +1 -1
@@ -1272,7 +1272,7 @@ static struct cpufreq_driver amd_pstate_
 	.online		= amd_pstate_epp_cpu_online,
 	.suspend	= amd_pstate_epp_suspend,
 	.resume		= amd_pstate_epp_resume,
-	.name		= "amd_pstate_epp",
+	.name		= "amd-pstate-epp",
 	.attr		= amd_pstate_epp_attr,
 };
 
author maintainer
#12 lore raw

PATCH 10/29 can: isotp: isotp_sendmsg(): fix return error fix on TX path

In reply to Greg Kroah-Hartman

From: Oliver Hartkopp <[email protected]>

commit e38910c0072b541a91954682c8b074a93e57c09b upstream.

With commit d674a8f123b4 ("can: isotp: isotp_sendmsg(): fix return error on FC timeout on TX path") the missing correct return value in the case of a protocol error was introduced.

But the way the error value has been read and sent to the user space does not follow the common scheme to clear the error after reading which is provided by the sock_error() function. This leads to an error report at the following write() attempt although everything should be working.

Fixes d674a8f123b4 ("can: isotp: isotp_sendmsg(): fix return error on FC timeout on TX path")
---
 net/can/isotp.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
net/can/isotp.c +3 -2
@@ -1079,8 +1079,9 @@ wait_free_buffer:
 		if (err)
 			goto err_event_drop;
 
-		if (sk->sk_err)
-			return -sk->sk_err;
+		err = sock_error(sk);
+		if (err)
+			return err;
 	}
 
 	return size;
author maintainer
#13 lore raw

PATCH 11/29 maple_tree: fix potential out-of-bounds access in mas_wr_end_piv()

In reply to Greg Kroah-Hartman

From: Peng Zhang <[email protected]>

commit cd00dd2585c4158e81fdfac0bbcc0446afbad26d upstream.

Check the write offset end bounds before using it as the offset into the pivot array. This avoids a possible out-of-bounds access on the pivot array if the write extends to the last slot in the node, in which case the node maximum should be used as the end pivot.

akpm: this doesn't affect any current callers, but new users of mapletree may encounter this problem if backported into earlier kernels, so let's fix it in -stable kernels in case of this.

---
 lib/maple_tree.c |   11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)
lib/maple_tree.c +6 -5
@@ -4287,11 +4287,13 @@ done:
 
 static inline void mas_wr_end_piv(struct ma_wr_state *wr_mas)
 {
-	while ((wr_mas->mas->last > wr_mas->end_piv) &&
-	       (wr_mas->offset_end < wr_mas->node_end))
-		wr_mas->end_piv = wr_mas->pivots[++wr_mas->offset_end];
+	while ((wr_mas->offset_end < wr_mas->node_end) &&
+	       (wr_mas->mas->last > wr_mas->pivots[wr_mas->offset_end]))
+		wr_mas->offset_end++;
 
-	if (wr_mas->mas->last > wr_mas->end_piv)
+	if (wr_mas->offset_end < wr_mas->node_end)
+		wr_mas->end_piv = wr_mas->pivots[wr_mas->offset_end];
+	else
 		wr_mas->end_piv = wr_mas->mas->max;
 }
 
@@ -4448,7 +4450,6 @@ static inline void *mas_wr_store_entry(s
 	}
 
 	/* At this point, we are at the leaf node that needs to be altered. */
-	wr_mas->end_piv = wr_mas->r_max;
 	mas_wr_end_piv(wr_mas);
 
 	if (!wr_mas->entry)
author maintainer
#14 lore raw

PATCH 12/29 mm: introduce new lock_mm_and_find_vma() page fault helper

In reply to Greg Kroah-Hartman

From: Linus Torvalds <[email protected]>

commit c2508ec5a58db67093f4fb8bf89a9a7c53a109e9 upstream.

.. and make x86 use it.

This basically extracts the existing x86 "find and expand faulting vma" code, but extends it to also take the mmap lock for writing in case we actually do need to expand the vma.

We've historically short-circuited that case, and have some rather ugly special logic to serialize the stack segment expansion (since we only hold the mmap lock for reading) that doesn't match the normal VM locking.

That slight violation of locking worked well, right up until it didn't:
the maple tree code really does want proper locking even for simple extension of an existing vma.

So extract the code for "look up the vma of the fault" from x86, fix it up to do the necessary write locking, and make it available as a helper function for other architectures that can use the common helper.

Note: I say "common helper", but it really only handles the normal stack-grows-down case. Which is all architectures except for PA-RISC and IA64. So some rare architectures can't use the helper, but if they care they'll just need to open-code this logic.

It's also worth pointing out that this code really would like to have an optimistic "mmap_upgrade_trylock()" to make it quicker to go from a read-lock (for the common case) to taking the write lock (for having to extend the vma) in the normal single-threaded situation where there is no other locking activity.

But that _is_ all the very uncommon special case, so while it would be nice to have such an operation, it probably doesn't matter in reality. I did put in the skeleton code for such a possible future expansion, even if it only acts as pseudo-documentation for what we're doing.

---
 arch/x86/Kconfig    |    1 
 arch/x86/mm/fault.c |   52 ----------------------
 include/linux/mm.h  |    2 
 mm/Kconfig          |    4 +
 mm/memory.c         |  121 ++++++++++++++++++++++++++++++++++++++++++++++++++++
 5 files changed, 130 insertions(+), 50 deletions(-)
arch/x86/Kconfig +1 -0
@@ -274,6 +274,7 @@ config X86
 	select HAVE_GENERIC_VDSO
 	select HOTPLUG_SMT			if SMP
 	select IRQ_FORCED_THREADING
+	select LOCK_MM_AND_FIND_VMA
 	select NEED_PER_CPU_EMBED_FIRST_CHUNK
 	select NEED_PER_CPU_PAGE_FIRST_CHUNK
 	select NEED_SG_DMA_LENGTH
arch/x86/mm/fault.c +2 -50

72 lines not on this page · raw message

include/linux/mm.h +2 -0
@@ -2190,6 +2190,8 @@ void unmap_mapping_pages(struct address_
 		pgoff_t start, pgoff_t nr, bool even_cows);
 void unmap_mapping_range(struct address_space *mapping,
 		loff_t const holebegin, loff_t const holelen, int even_cows);
+struct vm_area_struct *lock_mm_and_find_vma(struct mm_struct *mm,
+		unsigned long address, struct pt_regs *regs);
 #else
 static inline vm_fault_t handle_mm_fault(struct vm_area_struct *vma,
 					 unsigned long address, unsigned int flags,
mm/Kconfig +4 -0
@@ -1202,6 +1202,10 @@ config LRU_GEN_STATS
 	  This option has a per-memcg and per-node memory overhead.
 # }
 
+config LOCK_MM_AND_FIND_VMA
+	bool
+	depends on !STACK_GROWSUP
+
 source "mm/damon/Kconfig"
 
 endmenu
mm/memory.c +121 -0

127 lines not on this page · raw message

author maintainer
#15 lore raw

PATCH 13/29 mm: make the page fault mmap locking killable

In reply to Greg Kroah-Hartman

From: Linus Torvalds <[email protected]>

commit eda0047296a16d65a7f2bc60a408f70d178b2014 upstream.

This is done as a separate patch from introducing the new lock_mm_and_find_vma() helper, because while it's an obvious change, it's not what x86 used to do in this area.

We already abort the page fault on fatal signals anyway, so why should we wait for the mmap lock only to then abort later? With the new helper function that returns without the lock held on failure anyway, this is particularly easy and straightforward.

---
 mm/memory.c |    6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
mm/memory.c +2 -4
@@ -5247,8 +5247,7 @@ static inline bool get_mmap_lock_careful
 			return false;
 	}
 
-	mmap_read_lock(mm);
-	return true;
+	return !mmap_read_lock_killable(mm);
 }
 
 static inline bool mmap_upgrade_trylock(struct mm_struct *mm)
@@ -5272,8 +5271,7 @@ static inline bool upgrade_mmap_lock_car
 		if (!search_exception_tables(ip))
 			return false;
 	}
-	mmap_write_lock(mm);
-	return true;
+	return !mmap_write_lock_killable(mm);
 }
 
 /*
author maintainer
#16 lore raw

PATCH 14/29 arm64/mm: Convert to using lock_mm_and_find_vma()

In reply to Greg Kroah-Hartman

From: Linus Torvalds <[email protected]>

commit ae870a68b5d13d67cf4f18d47bb01ee3fee40acb upstream.

This converts arm64 to use the new page fault helper. It was very straightforward, but still needed a fix for the "obvious" conversion I initially did. Thanks to Suren for the fix and testing.

---
 arch/arm64/Kconfig    |    1 +
 arch/arm64/mm/fault.c |   44 +++++++-------------------------------------
 2 files changed, 8 insertions(+), 37 deletions(-)
arch/arm64/Kconfig +1 -0
@@ -219,6 +219,7 @@ config ARM64
 	select IRQ_DOMAIN
 	select IRQ_FORCED_THREADING
 	select KASAN_VMALLOC if KASAN
+	select LOCK_MM_AND_FIND_VMA
 	select MODULES_USE_ELF_RELA
 	select NEED_DMA_MAP_STATE
 	select NEED_SG_DMA_LENGTH
arch/arm64/mm/fault.c +7 -37

65 lines not on this page · raw message

author maintainer
#17 lore raw

PATCH 15/29 powerpc/mm: Convert to using lock_mm_and_find_vma()

In reply to Greg Kroah-Hartman

From: Michael Ellerman <[email protected]>

commit e6fe228c4ffafdfc970cf6d46883a1f481baf7ea upstream.

---
 arch/powerpc/Kconfig    |    1 +
 arch/powerpc/mm/fault.c |   41 ++++-------------------------------------
 2 files changed, 5 insertions(+), 37 deletions(-)
arch/powerpc/Kconfig +1 -0
@@ -263,6 +263,7 @@ config PPC
 	select IRQ_DOMAIN
 	select IRQ_FORCED_THREADING
 	select KASAN_VMALLOC			if KASAN && MODULES
+	select LOCK_MM_AND_FIND_VMA
 	select MMU_GATHER_PAGE_SIZE
 	select MMU_GATHER_RCU_TABLE_FREE
 	select MMU_GATHER_MERGE_VMAS
arch/powerpc/mm/fault.c +4 -37

55 lines not on this page · raw message

author maintainer
#18 lore raw

PATCH 16/29 mips/mm: Convert to using lock_mm_and_find_vma()

In reply to Greg Kroah-Hartman

From: Ben Hutchings <[email protected]>

commit 4bce37a68ff884e821a02a731897a8119e0c37b7 upstream.

---
 arch/mips/Kconfig    |    1 +
 arch/mips/mm/fault.c |   12 ++----------
 2 files changed, 3 insertions(+), 10 deletions(-)
arch/mips/Kconfig +1 -0
@@ -94,6 +94,7 @@ config MIPS
 	select HAVE_VIRT_CPU_ACCOUNTING_GEN if 64BIT || !SMP
 	select IRQ_FORCED_THREADING
 	select ISA if EISA
+	select LOCK_MM_AND_FIND_VMA
 	select MODULES_USE_ELF_REL if MODULES
 	select MODULES_USE_ELF_RELA if MODULES && 64BIT
 	select PERF_USE_VMALLOC
arch/mips/mm/fault.c +2 -10
@@ -99,21 +99,13 @@ static void __do_page_fault(struct pt_re
 
 	perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, address);
 retry:
-	mmap_read_lock(mm);
-	vma = find_vma(mm, address);
+	vma = lock_mm_and_find_vma(mm, address, regs);
 	if (!vma)
-		goto bad_area;
-	if (vma->vm_start <= address)
-		goto good_area;
-	if (!(vma->vm_flags & VM_GROWSDOWN))
-		goto bad_area;
-	if (expand_stack(vma, address))
-		goto bad_area;
+		goto bad_area_nosemaphore;
 /*
  * Ok, we have a good vm_area for this memory access, so
  * we can handle it..
  */
-good_area:
 	si_code = SEGV_ACCERR;
 
 	if (write) {
author maintainer
#19 lore raw

PATCH 17/29 riscv/mm: Convert to using lock_mm_and_find_vma()

In reply to Greg Kroah-Hartman

From: Ben Hutchings <[email protected]>

commit 7267ef7b0b77f4ed23b7b3c87d8eca7bd9c2d007 upstream.

---
 arch/riscv/Kconfig    |    1 +
 arch/riscv/mm/fault.c |   31 +++++++++++++------------------
 2 files changed, 14 insertions(+), 18 deletions(-)
arch/riscv/Kconfig +1 -0
@@ -119,6 +119,7 @@ config RISCV
 	select HAVE_SYSCALL_TRACEPOINTS
 	select IRQ_DOMAIN
 	select IRQ_FORCED_THREADING
+	select LOCK_MM_AND_FIND_VMA
 	select MODULES_USE_ELF_RELA if MODULES
 	select MODULE_SECTIONS if MODULES
 	select OF
arch/riscv/mm/fault.c +13 -18
@@ -83,13 +83,13 @@ static inline void mm_fault_error(struct
 	BUG();
 }
 
-static inline void bad_area(struct pt_regs *regs, struct mm_struct *mm, int code, unsigned long addr)
+static inline void
+bad_area_nosemaphore(struct pt_regs *regs, int code, unsigned long addr)
 {
 	/*
 	 * Something tried to access memory that isn't in our memory map.
 	 * Fix it, but check if it's kernel or user first.
 	 */
-	mmap_read_unlock(mm);
 	/* User mode accesses just cause a SIGSEGV */
 	if (user_mode(regs)) {
 		do_trap(regs, SIGSEGV, code, addr);
@@ -99,6 +99,15 @@ static inline void bad_area(struct pt_re
 	no_context(regs, addr);
 }
 
+static inline void
+bad_area(struct pt_regs *regs, struct mm_struct *mm, int code,
+	 unsigned long addr)
+{
+	mmap_read_unlock(mm);
+
+	bad_area_nosemaphore(regs, code, addr);
+}
+
 static inline void vmalloc_fault(struct pt_regs *regs, int code, unsigned long addr)
 {
 	pgd_t *pgd, *pgd_k;
@@ -286,23 +295,10 @@ asmlinkage void do_page_fault(struct pt_
 	else if (cause == EXC_INST_PAGE_FAULT)
 		flags |= FAULT_FLAG_INSTRUCTION;
 retry:
-	mmap_read_lock(mm);
-	vma = find_vma(mm, addr);
+	vma = lock_mm_and_find_vma(mm, addr, regs);
 	if (unlikely(!vma)) {
 		tsk->thread.bad_cause = cause;
-		bad_area(regs, mm, code, addr);
-		return;
-	}
-	if (likely(vma->vm_start <= addr))
-		goto good_area;
-	if (unlikely(!(vma->vm_flags & VM_GROWSDOWN))) {
-		tsk->thread.bad_cause = cause;
-		bad_area(regs, mm, code, addr);
-		return;
-	}
-	if (unlikely(expand_stack(vma, addr))) {
-		tsk->thread.bad_cause = cause;
-		bad_area(regs, mm, code, addr);
+		bad_area_nosemaphore(regs, code, addr);
 		return;
 	}
 
@@ -310,7 +306,6 @@ retry:
 	 * Ok, we have a good vm_area for this memory access, so
 	 * we can handle it.
 	 */
-good_area:
 	code = SEGV_ACCERR;
 
 	if (unlikely(access_error(cause, vma))) {
author maintainer
#20 lore raw

PATCH 18/29 arm/mm: Convert to using lock_mm_and_find_vma()

In reply to Greg Kroah-Hartman

From: Ben Hutchings <[email protected]>

commit 8b35ca3e45e35a26a21427f35d4093606e93ad0a upstream.

arm has an additional check for address < FIRST_USER_ADDRESS before expanding the stack. Since FIRST_USER_ADDRESS is defined everywhere (generally as 0), move that check to the generic expand_downwards().

---
 arch/arm/Kconfig    |    1 
 arch/arm/mm/fault.c |   63 +++++++++++-----------------------------------------
 mm/mmap.c           |    2 -
 3 files changed, 16 insertions(+), 50 deletions(-)
arch/arm/Kconfig +1 -0
@@ -125,6 +125,7 @@ config ARM
 	select HAVE_UID16
 	select HAVE_VIRT_CPU_ACCOUNTING_GEN
 	select IRQ_FORCED_THREADING
+	select LOCK_MM_AND_FIND_VMA
 	select MODULES_USE_ELF_REL
 	select NEED_DMA_MAP_STATE
 	select OF_EARLY_FLATTREE if OF
arch/arm/mm/fault.c +14 -49

88 lines not on this page · raw message

mm/mmap.c +1 -1
@@ -1999,7 +1999,7 @@ int expand_downwards(struct vm_area_stru
 	int error = 0;
 
 	address &= PAGE_MASK;
-	if (address < mmap_min_addr)
+	if (address < mmap_min_addr || address < FIRST_USER_ADDRESS)
 		return -EPERM;
 
 	/* Enforce stack_guard_gap */
author maintainer
#21 lore raw

PATCH 19/29 mm/fault: convert remaining simple cases to lock_mm_and_find_vma()

In reply to Greg Kroah-Hartman

From: Linus Torvalds <[email protected]>

commit a050ba1e7422f2cc60ff8bfde3f96d34d00cb585 upstream.

This does the simple pattern conversion of alpha, arc, csky, hexagon, loongarch, nios2, sh, sparc32, and xtensa to the lock_mm_and_find_vma() helper. They all have the regular fault handling pattern without odd special cases.

The remaining architectures all have something that keeps us from a straightforward conversion: ia64 and parisc have stacks that can grow both up as well as down (and ia64 has special address region checks).

And m68k, microblaze, openrisc, sparc64, and um end up having extra rules about only expanding the stack down a limited amount below the user space stack pointer. That is something that x86 used to do too (long long ago), and it probably could just be skipped, but it still makes the conversion less than trivial.

Note that this conversion was done manually and with the exception of alpha without any build testing, because I have a fairly limited cross- building environment. The cases are all simple, and I went through the changes several times, but...

---
 arch/alpha/Kconfig         |    1 +
 arch/alpha/mm/fault.c      |   13 +++----------
 arch/arc/Kconfig           |    1 +
 arch/arc/mm/fault.c        |   11 +++--------
 arch/csky/Kconfig          |    1 +
 arch/csky/mm/fault.c       |   22 +++++-----------------
 arch/hexagon/Kconfig       |    1 +
 arch/hexagon/mm/vm_fault.c |   18 ++++--------------
 arch/loongarch/Kconfig     |    1 +
 arch/loongarch/mm/fault.c  |   16 ++++++----------
 arch/nios2/Kconfig         |    1 +
 arch/nios2/mm/fault.c      |   17 ++---------------
 arch/sh/Kconfig            |    1 +
 arch/sh/mm/fault.c         |   17 ++---------------
 arch/sparc/Kconfig         |    1 +
 arch/sparc/mm/fault_32.c   |   32 ++++++++------------------------
 arch/xtensa/Kconfig        |    1 +
 arch/xtensa/mm/fault.c     |   14 +++-----------
 18 files changed, 45 insertions(+), 124 deletions(-)
arch/alpha/Kconfig +1 -0
@@ -29,6 +29,7 @@ config ALPHA
 	select GENERIC_SMP_IDLE_THREAD
 	select HAVE_ARCH_AUDITSYSCALL
 	select HAVE_MOD_ARCH_SPECIFIC
+	select LOCK_MM_AND_FIND_VMA
 	select MODULES_USE_ELF_RELA
 	select ODD_RT_SIGACTION
 	select OLD_SIGSUSPEND
arch/alpha/mm/fault.c +3 -10
@@ -119,20 +119,12 @@ do_page_fault(unsigned long address, uns
 		flags |= FAULT_FLAG_USER;
 	perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, address);
 retry:
-	mmap_read_lock(mm);
-	vma = find_vma(mm, address);
+	vma = lock_mm_and_find_vma(mm, address, regs);
 	if (!vma)
-		goto bad_area;
-	if (vma->vm_start <= address)
-		goto good_area;
-	if (!(vma->vm_flags & VM_GROWSDOWN))
-		goto bad_area;
-	if (expand_stack(vma, address))
-		goto bad_area;
+		goto bad_area_nosemaphore;
 
 	/* Ok, we have a good vm_area for this memory access, so
 	   we can handle it.  */
- good_area:
 	si_code = SEGV_ACCERR;
 	if (cause < 0) {
 		if (!(vma->vm_flags & VM_EXEC))
@@ -192,6 +184,7 @@ retry:
  bad_area:
 	mmap_read_unlock(mm);
 
+ bad_area_nosemaphore:
 	if (user_mode(regs))
 		goto do_sigsegv;
 
arch/arc/Kconfig +1 -0
@@ -41,6 +41,7 @@ config ARC
 	select HAVE_PERF_EVENTS
 	select HAVE_SYSCALL_TRACEPOINTS
 	select IRQ_DOMAIN
+	select LOCK_MM_AND_FIND_VMA
 	select MODULES_USE_ELF_RELA
 	select OF
 	select OF_EARLY_FLATTREE
arch/arc/mm/fault.c +3 -8
@@ -113,15 +113,9 @@ void do_page_fault(unsigned long address
 
 	perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, address);
 retry:
-	mmap_read_lock(mm);
-
-	vma = find_vma(mm, address);
+	vma = lock_mm_and_find_vma(mm, address, regs);
 	if (!vma)
-		goto bad_area;
-	if (unlikely(address < vma->vm_start)) {
-		if (!(vma->vm_flags & VM_GROWSDOWN) || expand_stack(vma, address))
-			goto bad_area;
-	}
+		goto bad_area_nosemaphore;
 
 	/*
 	 * vm_area is good, now check permissions for this memory access
@@ -161,6 +155,7 @@ retry:
 bad_area:
 	mmap_read_unlock(mm);
 
+bad_area_nosemaphore:
 	/*
 	 * Major/minor page fault accounting
 	 * (in case of retry we only land here once)
arch/csky/Kconfig +1 -0
@@ -96,6 +96,7 @@ config CSKY
 	select HAVE_REGS_AND_STACK_ACCESS_API
 	select HAVE_STACKPROTECTOR
 	select HAVE_SYSCALL_TRACEPOINTS
+	select LOCK_MM_AND_FIND_VMA
 	select MAY_HAVE_SPARSE_IRQ
 	select MODULES_USE_ELF_RELA if MODULES
 	select OF
arch/csky/mm/fault.c +5 -17
@@ -97,13 +97,12 @@ static inline void mm_fault_error(struct
 	BUG();
 }
 
-static inline void bad_area(struct pt_regs *regs, struct mm_struct *mm, int code, unsigned long addr)
+static inline void bad_area_nosemaphore(struct pt_regs *regs, struct mm_struct *mm, int code, unsigned long addr)
 {
 	/*
 	 * Something tried to access memory that isn't in our memory map.
 	 * Fix it, but check if it's kernel or user first.
 	 */
-	mmap_read_unlock(mm);
 	/* User mode accesses just cause a SIGSEGV */
 	if (user_mode(regs)) {
 		do_trap(regs, SIGSEGV, code, addr);
@@ -238,20 +237,9 @@ asmlinkage void do_page_fault(struct pt_
 	if (is_write(regs))
 		flags |= FAULT_FLAG_WRITE;
 retry:
-	mmap_read_lock(mm);
-	vma = find_vma(mm, addr);
+	vma = lock_mm_and_find_vma(mm, address, regs);
 	if (unlikely(!vma)) {
-		bad_area(regs, mm, code, addr);
-		return;
-	}
-	if (likely(vma->vm_start <= addr))
-		goto good_area;
-	if (unlikely(!(vma->vm_flags & VM_GROWSDOWN))) {
-		bad_area(regs, mm, code, addr);
-		return;
-	}
-	if (unlikely(expand_stack(vma, addr))) {
-		bad_area(regs, mm, code, addr);
+		bad_area_nosemaphore(regs, mm, code, addr);
 		return;
 	}
 
@@ -259,11 +247,11 @@ retry:
 	 * Ok, we have a good vm_area for this memory access, so
 	 * we can handle it.
 	 */
-good_area:
 	code = SEGV_ACCERR;
 
 	if (unlikely(access_error(regs, vma))) {
-		bad_area(regs, mm, code, addr);
+		mmap_read_unlock(mm);
+		bad_area_nosemaphore(regs, mm, code, addr);
 		return;
 	}
 
arch/hexagon/Kconfig +1 -0
@@ -28,6 +28,7 @@ config HEXAGON
 	select GENERIC_SMP_IDLE_THREAD
 	select STACKTRACE_SUPPORT
 	select GENERIC_CLOCKEVENTS_BROADCAST
+	select LOCK_MM_AND_FIND_VMA
 	select MODULES_USE_ELF_RELA
 	select GENERIC_CPU_DEVICES
 	select ARCH_WANT_LD_ORPHAN_WARN
arch/hexagon/mm/vm_fault.c +4 -14
@@ -57,21 +57,10 @@ void do_page_fault(unsigned long address
 
 	perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, address);
 retry:
-	mmap_read_lock(mm);
-	vma = find_vma(mm, address);
-	if (!vma)
-		goto bad_area;
+	vma = lock_mm_and_find_vma(mm, address, regs);
+	if (unlikely(!vma))
+		goto bad_area_nosemaphore;
 
-	if (vma->vm_start <= address)
-		goto good_area;
-
-	if (!(vma->vm_flags & VM_GROWSDOWN))
-		goto bad_area;
-
-	if (expand_stack(vma, address))
-		goto bad_area;
-
-good_area:
 	/* Address space is OK.  Now check access rights. */
 	si_code = SEGV_ACCERR;
 
@@ -143,6 +132,7 @@ good_area:
 bad_area:
 	mmap_read_unlock(mm);
 
+bad_area_nosemaphore:
 	if (user_mode(regs)) {
 		force_sig_fault(SIGSEGV, si_code, (void __user *)address);
 		return;
arch/loongarch/Kconfig +1 -0
@@ -125,6 +125,7 @@ config LOONGARCH
 	select HAVE_VIRT_CPU_ACCOUNTING_GEN if !SMP
 	select IRQ_FORCED_THREADING
 	select IRQ_LOONGARCH_CPU
+	select LOCK_MM_AND_FIND_VMA
 	select MMU_GATHER_MERGE_VMAS if MMU
 	select MODULES_USE_ELF_RELA if MODULES
 	select NEED_PER_CPU_EMBED_FIRST_CHUNK
arch/loongarch/mm/fault.c +6 -10
@@ -169,22 +169,18 @@ static void __kprobes __do_page_fault(st
 
 	perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, address);
 retry:
-	mmap_read_lock(mm);
-	vma = find_vma(mm, address);
-	if (!vma)
-		goto bad_area;
-	if (vma->vm_start <= address)
-		goto good_area;
-	if (!(vma->vm_flags & VM_GROWSDOWN))
-		goto bad_area;
-	if (!expand_stack(vma, address))
-		goto good_area;
+	vma = lock_mm_and_find_vma(mm, address, regs);
+	if (unlikely(!vma))
+		goto bad_area_nosemaphore;
+	goto good_area;
+
 /*
  * Something tried to access memory that isn't in our memory map..
  * Fix it, but check if it's kernel or user first..
  */
 bad_area:
 	mmap_read_unlock(mm);
+bad_area_nosemaphore:
 	do_sigsegv(regs, write, address, si_code);
 	return;
 
arch/nios2/Kconfig +1 -0
@@ -16,6 +16,7 @@ config NIOS2
 	select HAVE_ARCH_TRACEHOOK
 	select HAVE_ARCH_KGDB
 	select IRQ_DOMAIN
+	select LOCK_MM_AND_FIND_VMA
 	select MODULES_USE_ELF_RELA
 	select OF
 	select OF_EARLY_FLATTREE
arch/nios2/mm/fault.c +2 -15
@@ -86,27 +86,14 @@ asmlinkage void do_page_fault(struct pt_
 
 	perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, address);
 
-	if (!mmap_read_trylock(mm)) {
-		if (!user_mode(regs) && !search_exception_tables(regs->ea))
-			goto bad_area_nosemaphore;
 retry:
-		mmap_read_lock(mm);
-	}
-
-	vma = find_vma(mm, address);
+	vma = lock_mm_and_find_vma(mm, address, regs);
 	if (!vma)
-		goto bad_area;
-	if (vma->vm_start <= address)
-		goto good_area;
-	if (!(vma->vm_flags & VM_GROWSDOWN))
-		goto bad_area;
-	if (expand_stack(vma, address))
-		goto bad_area;
+		goto bad_area_nosemaphore;
 /*
  * Ok, we have a good vm_area for this memory access, so
  * we can handle it..
  */
-good_area:
 	code = SEGV_ACCERR;
 
 	switch (cause) {
arch/sh/Kconfig +1 -0
@@ -56,6 +56,7 @@ config SUPERH
 	select HAVE_STACKPROTECTOR
 	select HAVE_SYSCALL_TRACEPOINTS
 	select IRQ_FORCED_THREADING
+	select LOCK_MM_AND_FIND_VMA
 	select MODULES_USE_ELF_RELA
 	select NEED_SG_DMA_LENGTH
 	select NO_DMA if !MMU && !DMA_COHERENT
arch/sh/mm/fault.c +2 -15
@@ -439,21 +439,9 @@ asmlinkage void __kprobes do_page_fault(
 	}
 
 retry:
-	mmap_read_lock(mm);
-
-	vma = find_vma(mm, address);
+	vma = lock_mm_and_find_vma(mm, address, regs);
 	if (unlikely(!vma)) {
-		bad_area(regs, error_code, address);
-		return;
-	}
-	if (likely(vma->vm_start <= address))
-		goto good_area;
-	if (unlikely(!(vma->vm_flags & VM_GROWSDOWN))) {
-		bad_area(regs, error_code, address);
-		return;
-	}
-	if (unlikely(expand_stack(vma, address))) {
-		bad_area(regs, error_code, address);
+		bad_area_nosemaphore(regs, error_code, address);
 		return;
 	}
 
@@ -461,7 +449,6 @@ retry:
 	 * Ok, we have a good vm_area for this memory access, so
 	 * we can handle it..
 	 */
-good_area:
 	if (unlikely(access_error(error_code, vma))) {
 		bad_area_access_error(regs, error_code, address);
 		return;
arch/sparc/Kconfig +1 -0
@@ -56,6 +56,7 @@ config SPARC32
 	select DMA_DIRECT_REMAP
 	select GENERIC_ATOMIC64
 	select HAVE_UID16
+	select LOCK_MM_AND_FIND_VMA
 	select OLD_SIGACTION
 	select ZONE_DMA
 
arch/sparc/mm/fault_32.c +8 -24
@@ -143,28 +143,19 @@ asmlinkage void do_sparc_fault(struct pt
 	if (pagefault_disabled() || !mm)
 		goto no_context;
 
+	if (!from_user && address >= PAGE_OFFSET)
+		goto no_context;
+
 	perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, address);
 
 retry:
-	mmap_read_lock(mm);
-
-	if (!from_user && address >= PAGE_OFFSET)
-		goto bad_area;
-
-	vma = find_vma(mm, address);
+	vma = lock_mm_and_find_vma(mm, address, regs);
 	if (!vma)
-		goto bad_area;
-	if (vma->vm_start <= address)
-		goto good_area;
-	if (!(vma->vm_flags & VM_GROWSDOWN))
-		goto bad_area;
-	if (expand_stack(vma, address))
-		goto bad_area;
+		goto bad_area_nosemaphore;
 	/*
 	 * Ok, we have a good vm_area for this memory access, so
 	 * we can handle it..
 	 */
-good_area:
 	code = SEGV_ACCERR;
 	if (write) {
 		if (!(vma->vm_flags & VM_WRITE))
@@ -321,17 +312,9 @@ static void force_user_fault(unsigned lo
 
 	code = SEGV_MAPERR;
 
-	mmap_read_lock(mm);
-	vma = find_vma(mm, address);
+	vma = lock_mm_and_find_vma(mm, address, regs);
 	if (!vma)
-		goto bad_area;
-	if (vma->vm_start <= address)
-		goto good_area;
-	if (!(vma->vm_flags & VM_GROWSDOWN))
-		goto bad_area;
-	if (expand_stack(vma, address))
-		goto bad_area;
-good_area:
+		goto bad_area_nosemaphore;
 	code = SEGV_ACCERR;
 	if (write) {
 		if (!(vma->vm_flags & VM_WRITE))
@@ -350,6 +333,7 @@ good_area:
 	return;
 bad_area:
 	mmap_read_unlock(mm);
+bad_area_nosemaphore:
 	__do_fault_siginfo(code, SIGSEGV, tsk->thread.kregs, address);
 	return;
 
arch/xtensa/Kconfig +1 -0
@@ -49,6 +49,7 @@ config XTENSA
 	select HAVE_SYSCALL_TRACEPOINTS
 	select HAVE_VIRT_CPU_ACCOUNTING_GEN
 	select IRQ_DOMAIN
+	select LOCK_MM_AND_FIND_VMA
 	select MODULES_USE_ELF_RELA
 	select PERF_USE_VMALLOC
 	select TRACE_IRQFLAGS_SUPPORT
arch/xtensa/mm/fault.c +3 -11
@@ -130,23 +130,14 @@ void do_page_fault(struct pt_regs *regs)
 	perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, address);
 
 retry:
-	mmap_read_lock(mm);
-	vma = find_vma(mm, address);
-
+	vma = lock_mm_and_find_vma(mm, address, regs);
 	if (!vma)
-		goto bad_area;
-	if (vma->vm_start <= address)
-		goto good_area;
-	if (!(vma->vm_flags & VM_GROWSDOWN))
-		goto bad_area;
-	if (expand_stack(vma, address))
-		goto bad_area;
+		goto bad_area_nosemaphore;
 
 	/* Ok, we have a good vm_area for this memory access, so
 	 * we can handle it..
 	 */
 
-good_area:
 	code = SEGV_ACCERR;
 
 	if (is_write) {
@@ -205,6 +196,7 @@ good_area:
 	 */
 bad_area:
 	mmap_read_unlock(mm);
+bad_area_nosemaphore:
 	if (user_mode(regs)) {
 		force_sig_fault(SIGSEGV, code, (void *) address);
 		return;
author maintainer
#22 lore raw

PATCH 20/29 powerpc/mm: convert coprocessor fault to lock_mm_and_find_vma()

In reply to Greg Kroah-Hartman

From: Linus Torvalds <[email protected]>

commit 2cd76c50d0b41cec5c87abfcdf25b236a2793fb6 upstream.

This is one of the simple cases, except there's no pt_regs pointer. Which is fine, as lock_mm_and_find_vma() is set up to work fine with a NULL pt_regs.

Powerpc already enabled LOCK_MM_AND_FIND_VMA for the main CPU faulting, so we can just use the helper without any extra work.

---
 arch/powerpc/mm/copro_fault.c |   14 +++-----------
 1 file changed, 3 insertions(+), 11 deletions(-)
arch/powerpc/mm/copro_fault.c +3 -11
@@ -33,19 +33,11 @@ int copro_handle_mm_fault(struct mm_stru
 	if (mm->pgd == NULL)
 		return -EFAULT;
 
-	mmap_read_lock(mm);
-	ret = -EFAULT;
-	vma = find_vma(mm, ea);
+	vma = lock_mm_and_find_vma(mm, ea, NULL);
 	if (!vma)
-		goto out_unlock;
-
-	if (ea < vma->vm_start) {
-		if (!(vma->vm_flags & VM_GROWSDOWN))
-			goto out_unlock;
-		if (expand_stack(vma, ea))
-			goto out_unlock;
-	}
+		return -EFAULT;
 
+	ret = -EFAULT;
 	is_write = dsisr & DSISR_ISSTORE;
 	if (is_write) {
 		if (!(vma->vm_flags & VM_WRITE))
author maintainer
#23 lore raw

PATCH 21/29 mm: make find_extend_vma() fail if write lock not held

In reply to Greg Kroah-Hartman

From: Liam R. Howlett <[email protected]>

commit f440fa1ac955e2898893f9301568435eb5cdfc4b upstream.

Make calls to extend_vma() and find_extend_vma() fail if the write lock is required.

To avoid making this a flag-day event, this still allows the old read-locking case for the trivial situations, and passes in a flag to say "is it write-locked". That way write-lockers can say "yes, I'm being careful", and legacy users will continue to work in all the common cases until they have been fully converted to the new world order.

---
 fs/binfmt_elf.c    |    6 +++---
 fs/exec.c          |    5 +++--
 include/linux/mm.h |   10 +++++++---
 mm/memory.c        |    2 +-
 mm/mmap.c          |   50 +++++++++++++++++++++++++++++++++-----------------
 mm/nommu.c         |    3 ++-
 6 files changed, 49 insertions(+), 27 deletions(-)
fs/binfmt_elf.c +3 -3
@@ -320,10 +320,10 @@ create_elf_tables(struct linux_binprm *b
 	 * Grow the stack manually; some architectures have a limit on how
 	 * far ahead a user-space access may be in order to grow the stack.
 	 */
-	if (mmap_read_lock_killable(mm))
+	if (mmap_write_lock_killable(mm))
 		return -EINTR;
-	vma = find_extend_vma(mm, bprm->p);
-	mmap_read_unlock(mm);
+	vma = find_extend_vma_locked(mm, bprm->p, true);
+	mmap_write_unlock(mm);
 	if (!vma)
 		return -EFAULT;
 
fs/exec.c +3 -2
@@ -204,7 +204,8 @@ static struct page *get_arg_page(struct
 
 #ifdef CONFIG_STACK_GROWSUP
 	if (write) {
-		ret = expand_downwards(bprm->vma, pos);
+		/* We claim to hold the lock - nobody to race with */
+		ret = expand_downwards(bprm->vma, pos, true);
 		if (ret < 0)
 			return NULL;
 	}
@@ -852,7 +853,7 @@ int setup_arg_pages(struct linux_binprm
 	stack_base = vma->vm_end - stack_expand;
 #endif
 	current->mm->start_stack = bprm->p;
-	ret = expand_stack(vma, stack_base);
+	ret = expand_stack_locked(vma, stack_base, true);
 	if (ret)
 		ret = -EFAULT;
 
include/linux/mm.h +7 -3
@@ -3065,11 +3065,13 @@ extern vm_fault_t filemap_page_mkwrite(s
 
 extern unsigned long stack_guard_gap;
 /* Generic expand stack which grows the stack according to GROWS{UP,DOWN} */
-extern int expand_stack(struct vm_area_struct *vma, unsigned long address);
+int expand_stack_locked(struct vm_area_struct *vma, unsigned long address,
+		bool write_locked);
+#define expand_stack(vma,addr) expand_stack_locked(vma,addr,false)
 
 /* CONFIG_STACK_GROWSUP still needs to grow downwards at some places */
-extern int expand_downwards(struct vm_area_struct *vma,
-		unsigned long address);
+int expand_downwards(struct vm_area_struct *vma, unsigned long address,
+		bool write_locked);
 #if VM_GROWSUP
 extern int expand_upwards(struct vm_area_struct *vma, unsigned long address);
 #else
@@ -3170,6 +3172,8 @@ unsigned long change_prot_numa(struct vm
 #endif
 
 struct vm_area_struct *find_extend_vma(struct mm_struct *, unsigned long addr);
+struct vm_area_struct *find_extend_vma_locked(struct mm_struct *,
+		unsigned long addr, bool write_locked);
 int remap_pfn_range(struct vm_area_struct *, unsigned long addr,
 			unsigned long pfn, unsigned long size, pgprot_t);
 int remap_pfn_range_notrack(struct vm_area_struct *vma, unsigned long addr,
mm/memory.c +1 -1
@@ -5336,7 +5336,7 @@ struct vm_area_struct *lock_mm_and_find_
 			goto fail;
 	}
 
-	if (expand_stack(vma, addr))
+	if (expand_stack_locked(vma, addr, true))
 		goto fail;
 
 success:
mm/mmap.c +33 -17

112 lines not on this page · raw message

mm/nommu.c +2 -1
@@ -643,7 +643,8 @@ struct vm_area_struct *find_extend_vma(s
  * expand a stack to a given address
  * - not supported under NOMMU conditions
  */
-int expand_stack(struct vm_area_struct *vma, unsigned long address)
+int expand_stack_locked(struct vm_area_struct *vma, unsigned long address,
+		bool write_locked)
 {
 	return -ENOMEM;
 }
author maintainer
#24 lore raw

PATCH 22/29 execve: expand new process stack manually ahead of time

In reply to Greg Kroah-Hartman

From: Linus Torvalds <[email protected]>

commit f313c51d26aa87e69633c9b46efb37a930faca71 upstream.

This is a small step towards a model where GUP itself would not expand the stack, and any user that needs GUP to not look up existing mappings, but actually expand on them, would have to do so manually before-hand, and with the mm lock held for writing.

It turns out that execve() already did almost exactly that, except it didn't take the mm lock at all (it's single-threaded so no locking technically needed, but it could cause lockdep errors). And it only did it for the CONFIG_STACK_GROWSUP case, since in that case GUP has obviously never expanded the stack downwards.

So just make that CONFIG_STACK_GROWSUP case do the right thing with locking, and enable it generally. This will eventually help GUP, and in the meantime avoids a special case and the lockdep issue.

---
 fs/exec.c |   37 +++++++++++++++++++++----------------
 1 file changed, 21 insertions(+), 16 deletions(-)
fs/exec.c +21 -16
@@ -199,34 +199,39 @@ static struct page *get_arg_page(struct
 		int write)
 {
 	struct page *page;
+	struct vm_area_struct *vma = bprm->vma;
+	struct mm_struct *mm = bprm->mm;
 	int ret;
-	unsigned int gup_flags = 0;
 
-#ifdef CONFIG_STACK_GROWSUP
-	if (write) {
-		/* We claim to hold the lock - nobody to race with */
-		ret = expand_downwards(bprm->vma, pos, true);
-		if (ret < 0)
+	/*
+	 * Avoid relying on expanding the stack down in GUP (which
+	 * does not work for STACK_GROWSUP anyway), and just do it
+	 * by hand ahead of time.
+	 */
+	if (write && pos < vma->vm_start) {
+		mmap_write_lock(mm);
+		ret = expand_downwards(vma, pos, true);
+		if (unlikely(ret < 0)) {
+			mmap_write_unlock(mm);
 			return NULL;
-	}
-#endif
-
-	if (write)
-		gup_flags |= FOLL_WRITE;
+		}
+		mmap_write_downgrade(mm);
+	} else
+		mmap_read_lock(mm);
 
 	/*
 	 * We are doing an exec().  'current' is the process
-	 * doing the exec and bprm->mm is the new process's mm.
+	 * doing the exec and 'mm' is the new process's mm.
 	 */
-	mmap_read_lock(bprm->mm);
-	ret = get_user_pages_remote(bprm->mm, pos, 1, gup_flags,
+	ret = get_user_pages_remote(mm, pos, 1,
+			write ? FOLL_WRITE : 0,
 			&page, NULL, NULL);
-	mmap_read_unlock(bprm->mm);
+	mmap_read_unlock(mm);
 	if (ret <= 0)
 		return NULL;
 
 	if (write)
-		acct_arg_size(bprm, vma_pages(bprm->vma));
+		acct_arg_size(bprm, vma_pages(vma));
 
 	return page;
 }
author maintainer
#25 lore raw

PATCH 23/29 mm: always expand the stack with the mmap write lock held

In reply to Greg Kroah-Hartman

From: Linus Torvalds <[email protected]>

commit 8d7071af890768438c14db6172cc8f9f4d04e184 upstream.

This finishes the job of always holding the mmap write lock when extending the user stack vma, and removes the 'write_locked' argument from the vm helper functions again.

For some cases, we just avoid expanding the stack at all: drivers and page pinning really shouldn't be extending any stacks. Let's see if any strange users really wanted that.

It's worth noting that architectures that weren't converted to the new lock_mm_and_find_vma() helper function are left using the legacy "expand_stack()" function, but it has been changed to drop the mmap_lock and take it for writing while expanding the vma. This makes it fairly straightforward to convert the remaining architectures.

As a result of dropping and re-taking the lock, the calling conventions for this function have also changed, since the old vma may no longer be valid. So it will now return the new vma if successful, and NULL - and the lock dropped - if the area could not be extended.

---
 arch/ia64/mm/fault.c         |   36 ++----------
 arch/m68k/mm/fault.c         |    9 ++-
 arch/microblaze/mm/fault.c   |    5 +
 arch/openrisc/mm/fault.c     |    5 +
 arch/parisc/mm/fault.c       |   23 +++-----
 arch/s390/mm/fault.c         |    5 +
 arch/sparc/mm/fault_64.c     |    8 +-
 arch/um/kernel/trap.c        |   11 ++-
 drivers/iommu/amd/iommu_v2.c |    4 -
 drivers/iommu/iommu-sva.c    |    2 
 fs/binfmt_elf.c              |    2 
 fs/exec.c                    |    4 -
 include/linux/mm.h           |   16 +----
 mm/gup.c                     |    6 +-
 mm/memory.c                  |   10 +++
 mm/mmap.c                    |  121 ++++++++++++++++++++++++++++++++++---------
 mm/nommu.c                   |   18 ++----
 17 files changed, 169 insertions(+), 116 deletions(-)
arch/ia64/mm/fault.c +6 -30
@@ -110,10 +110,12 @@ retry:
          * register backing store that needs to expand upwards, in
          * this case vma will be null, but prev_vma will ne non-null
          */
-        if (( !vma && prev_vma ) || (address < vma->vm_start) )
-		goto check_expansion;
+        if (( !vma && prev_vma ) || (address < vma->vm_start) ) {
+		vma = expand_stack(mm, address);
+		if (!vma)
+			goto bad_area_nosemaphore;
+	}
 
-  good_area:
 	code = SEGV_ACCERR;
 
 	/* OK, we've got a good vm_area for this memory area.  Check the access permissions: */
@@ -177,35 +179,9 @@ retry:
 	mmap_read_unlock(mm);
 	return;
 
-  check_expansion:
-	if (!(prev_vma && (prev_vma->vm_flags & VM_GROWSUP) && (address == prev_vma->vm_end))) {
-		if (!vma)
-			goto bad_area;
-		if (!(vma->vm_flags & VM_GROWSDOWN))
-			goto bad_area;
-		if (REGION_NUMBER(address) != REGION_NUMBER(vma->vm_start)
-		    || REGION_OFFSET(address) >= RGN_MAP_LIMIT)
-			goto bad_area;
-		if (expand_stack(vma, address))
-			goto bad_area;
-	} else {
-		vma = prev_vma;
-		if (REGION_NUMBER(address) != REGION_NUMBER(vma->vm_start)
-		    || REGION_OFFSET(address) >= RGN_MAP_LIMIT)
-			goto bad_area;
-		/*
-		 * Since the register backing store is accessed sequentially,
-		 * we disallow growing it by more than a page at a time.
-		 */
-		if (address > vma->vm_end + PAGE_SIZE - sizeof(long))
-			goto bad_area;
-		if (expand_upwards(vma, address))
-			goto bad_area;
-	}
-	goto good_area;
-
   bad_area:
 	mmap_read_unlock(mm);
+  bad_area_nosemaphore:
 	if ((isr & IA64_ISR_SP)
 	    || ((isr & IA64_ISR_NA) && (isr & IA64_ISR_CODE_MASK) == IA64_ISR_CODE_LFETCH))
 	{
arch/m68k/mm/fault.c +6 -3
@@ -105,8 +105,9 @@ retry:
 		if (address + 256 < rdusp())
 			goto map_err;
 	}
-	if (expand_stack(vma, address))
-		goto map_err;
+	vma = expand_stack(mm, address);
+	if (!vma)
+		goto map_err_nosemaphore;
 
 /*
  * Ok, we have a good vm_area for this memory access, so
@@ -196,10 +197,12 @@ bus_err:
 	goto send_sig;
 
 map_err:
+	mmap_read_unlock(mm);
+map_err_nosemaphore:
 	current->thread.signo = SIGSEGV;
 	current->thread.code = SEGV_MAPERR;
 	current->thread.faddr = address;
-	goto send_sig;
+	return send_fault_sig(regs);
 
 acc_err:
 	current->thread.signo = SIGSEGV;
arch/microblaze/mm/fault.c +3 -2
@@ -192,8 +192,9 @@ retry:
 			&& (kernel_mode(regs) || !store_updates_sp(regs)))
 				goto bad_area;
 	}
-	if (expand_stack(vma, address))
-		goto bad_area;
+	vma = expand_stack(mm, address);
+	if (!vma)
+		goto bad_area_nosemaphore;
 
 good_area:
 	code = SEGV_ACCERR;
arch/openrisc/mm/fault.c +3 -2
@@ -127,8 +127,9 @@ retry:
 		if (address + PAGE_SIZE < regs->sp)
 			goto bad_area;
 	}
-	if (expand_stack(vma, address))
-		goto bad_area;
+	vma = expand_stack(mm, address);
+	if (!vma)
+		goto bad_area_nosemaphore;
 
 	/*
 	 * Ok, we have a good vm_area for this memory access, so
arch/parisc/mm/fault.c +11 -12
@@ -288,15 +288,19 @@ void do_page_fault(struct pt_regs *regs,
 retry:
 	mmap_read_lock(mm);
 	vma = find_vma_prev(mm, address, &prev_vma);
-	if (!vma || address < vma->vm_start)
-		goto check_expansion;
+	if (!vma || address < vma->vm_start) {
+		if (!prev || !(prev->vm_flags & VM_GROWSUP))
+			goto bad_area;
+		vma = expand_stack(mm, address);
+		if (!vma)
+			goto bad_area_nosemaphore;
+	}
+
 /*
  * Ok, we have a good vm_area for this memory access. We still need to
  * check the access permissions.
  */
 
-good_area:
-
 	if ((vma->vm_flags & acc_type) != acc_type)
 		goto bad_area;
 
@@ -347,17 +351,13 @@ good_area:
 	mmap_read_unlock(mm);
 	return;
 
-check_expansion:
-	vma = prev_vma;
-	if (vma && (expand_stack(vma, address) == 0))
-		goto good_area;
-
 /*
  * Something tried to access memory that isn't in our memory map..
  */
 bad_area:
 	mmap_read_unlock(mm);
 
+bad_area_nosemaphore:
 	if (user_mode(regs)) {
 		int signo, si_code;
 
@@ -449,7 +449,7 @@ handle_nadtlb_fault(struct pt_regs *regs
 {
 	unsigned long insn = regs->iir;
 	int breg, treg, xreg, val = 0;
-	struct vm_area_struct *vma, *prev_vma;
+	struct vm_area_struct *vma;
 	struct task_struct *tsk;
 	struct mm_struct *mm;
 	unsigned long address;
@@ -485,7 +485,7 @@ handle_nadtlb_fault(struct pt_regs *regs
 				/* Search for VMA */
 				address = regs->ior;
 				mmap_read_lock(mm);
-				vma = find_vma_prev(mm, address, &prev_vma);
+				vma = vma_lookup(mm, address);
 				mmap_read_unlock(mm);
 
 				/*
@@ -494,7 +494,6 @@ handle_nadtlb_fault(struct pt_regs *regs
 				 */
 				acc_type = (insn & 0x40) ? VM_WRITE : VM_READ;
 				if (vma
-				    && address >= vma->vm_start
 				    && (vma->vm_flags & acc_type) == acc_type)
 					val = 1;
 			}
arch/s390/mm/fault.c +3 -2
@@ -433,8 +433,9 @@ retry:
 	if (unlikely(vma->vm_start > address)) {
 		if (!(vma->vm_flags & VM_GROWSDOWN))
 			goto out_up;
-		if (expand_stack(vma, address))
-			goto out_up;
+		vma = expand_stack(mm, address);
+		if (!vma)
+			goto out;
 	}
 
 	/*
arch/sparc/mm/fault_64.c +5 -3
@@ -383,8 +383,9 @@ continue_fault:
 				goto bad_area;
 		}
 	}
-	if (expand_stack(vma, address))
-		goto bad_area;
+	vma = expand_stack(mm, address);
+	if (!vma)
+		goto bad_area_nosemaphore;
 	/*
 	 * Ok, we have a good vm_area for this memory access, so
 	 * we can handle it..
@@ -487,8 +488,9 @@ exit_exception:
 	 * Fix it, but check if it's kernel or user first..
 	 */
 bad_area:
-	insn = get_fault_insn(regs, insn);
 	mmap_read_unlock(mm);
+bad_area_nosemaphore:
+	insn = get_fault_insn(regs, insn);
 
 handle_kernel_fault:
 	do_kernel_fault(regs, si_code, fault_code, insn, address);
arch/um/kernel/trap.c +6 -5
@@ -47,14 +47,15 @@ retry:
 	vma = find_vma(mm, address);
 	if (!vma)
 		goto out;
-	else if (vma->vm_start <= address)
+	if (vma->vm_start <= address)
 		goto good_area;
-	else if (!(vma->vm_flags & VM_GROWSDOWN))
+	if (!(vma->vm_flags & VM_GROWSDOWN))
 		goto out;
-	else if (is_user && !ARCH_IS_STACKGROW(address))
-		goto out;
-	else if (expand_stack(vma, address))
+	if (is_user && !ARCH_IS_STACKGROW(address))
 		goto out;
+	vma = expand_stack(mm, address);
+	if (!vma)
+		goto out_nosemaphore;
 
 good_area:
 	*code_out = SEGV_ACCERR;
drivers/iommu/amd/iommu_v2.c +2 -2
@@ -485,8 +485,8 @@ static void do_fault(struct work_struct
 	flags |= FAULT_FLAG_REMOTE;
 
 	mmap_read_lock(mm);
-	vma = find_extend_vma(mm, address);
-	if (!vma || address < vma->vm_start)
+	vma = vma_lookup(mm, address);
+	if (!vma)
 		/* failed to get a vma in the right range */
 		goto out;
 
drivers/iommu/iommu-sva.c +1 -1
@@ -203,7 +203,7 @@ iommu_sva_handle_iopf(struct iommu_fault
 
 	mmap_read_lock(mm);
 
-	vma = find_extend_vma(mm, prm->addr);
+	vma = vma_lookup(mm, prm->addr);
 	if (!vma)
 		/* Unmapped area */
 		goto out_put_mm;
fs/binfmt_elf.c +1 -1
@@ -322,7 +322,7 @@ create_elf_tables(struct linux_binprm *b
 	 */
 	if (mmap_write_lock_killable(mm))
 		return -EINTR;
-	vma = find_extend_vma_locked(mm, bprm->p, true);
+	vma = find_extend_vma_locked(mm, bprm->p);
 	mmap_write_unlock(mm);
 	if (!vma)
 		return -EFAULT;
fs/exec.c +2 -2
@@ -210,7 +210,7 @@ static struct page *get_arg_page(struct
 	 */
 	if (write && pos < vma->vm_start) {
 		mmap_write_lock(mm);
-		ret = expand_downwards(vma, pos, true);
+		ret = expand_downwards(vma, pos);
 		if (unlikely(ret < 0)) {
 			mmap_write_unlock(mm);
 			return NULL;
@@ -858,7 +858,7 @@ int setup_arg_pages(struct linux_binprm
 	stack_base = vma->vm_end - stack_expand;
 #endif
 	current->mm->start_stack = bprm->p;
-	ret = expand_stack_locked(vma, stack_base, true);
+	ret = expand_stack_locked(vma, stack_base);
 	if (ret)
 		ret = -EFAULT;
 
include/linux/mm.h +4 -12
@@ -3065,18 +3065,11 @@ extern vm_fault_t filemap_page_mkwrite(s
 
 extern unsigned long stack_guard_gap;
 /* Generic expand stack which grows the stack according to GROWS{UP,DOWN} */
-int expand_stack_locked(struct vm_area_struct *vma, unsigned long address,
-		bool write_locked);
-#define expand_stack(vma,addr) expand_stack_locked(vma,addr,false)
+int expand_stack_locked(struct vm_area_struct *vma, unsigned long address);
+struct vm_area_struct *expand_stack(struct mm_struct * mm, unsigned long addr);
 
 /* CONFIG_STACK_GROWSUP still needs to grow downwards at some places */
-int expand_downwards(struct vm_area_struct *vma, unsigned long address,
-		bool write_locked);
-#if VM_GROWSUP
-extern int expand_upwards(struct vm_area_struct *vma, unsigned long address);
-#else
-  #define expand_upwards(vma, address) (0)
-#endif
+int expand_downwards(struct vm_area_struct *vma, unsigned long address);
 
 /* Look up the first VMA which satisfies  addr < vm_end,  NULL if none. */
 extern struct vm_area_struct * find_vma(struct mm_struct * mm, unsigned long addr);
@@ -3171,9 +3164,8 @@ unsigned long change_prot_numa(struct vm
 			unsigned long start, unsigned long end);
 #endif
 
-struct vm_area_struct *find_extend_vma(struct mm_struct *, unsigned long addr);
 struct vm_area_struct *find_extend_vma_locked(struct mm_struct *,
-		unsigned long addr, bool write_locked);
+		unsigned long addr);
 int remap_pfn_range(struct vm_area_struct *, unsigned long addr,
 			unsigned long pfn, unsigned long size, pgprot_t);
 int remap_pfn_range_notrack(struct vm_area_struct *vma, unsigned long addr,
mm/gup.c +3 -3
@@ -1096,7 +1096,7 @@ static long __get_user_pages(struct mm_s
 
 		/* first iteration or cross vma bound */
 		if (!vma || start >= vma->vm_end) {
-			vma = find_extend_vma(mm, start);
+			vma = vma_lookup(mm, start);
 			if (!vma && in_gate_area(mm, start)) {
 				ret = get_gate_page(mm, start & PAGE_MASK,
 						gup_flags, &vma,
@@ -1265,8 +1265,8 @@ int fixup_user_fault(struct mm_struct *m
 		fault_flags |= FAULT_FLAG_ALLOW_RETRY | FAULT_FLAG_KILLABLE;
 
 retry:
-	vma = find_extend_vma(mm, address);
-	if (!vma || address < vma->vm_start)
+	vma = vma_lookup(mm, address);
+	if (!vma)
 		return -EFAULT;
 
 	if (!vma_permits_fault(vma, fault_flags))
mm/memory.c +9 -1
@@ -5336,7 +5336,7 @@ struct vm_area_struct *lock_mm_and_find_
 			goto fail;
 	}
 
-	if (expand_stack_locked(vma, addr, true))
+	if (expand_stack_locked(vma, addr))
 		goto fail;
 
 success:
@@ -5620,6 +5620,14 @@ int __access_remote_vm(struct mm_struct
 	if (mmap_read_lock_killable(mm))
 		return 0;
 
+	/* We might need to expand the stack to access it */
+	vma = vma_lookup(mm, addr);
+	if (!vma) {
+		vma = expand_stack(mm, addr);
+		if (!vma)
+			return 0;
+	}
+
 	/* ignore errors, just check how much was successfully transferred */
 	while (len) {
 		int bytes, ret, offset;
mm/mmap.c +97 -24

192 lines not on this page · raw message

mm/nommu.c +7 -11
@@ -631,24 +631,20 @@ struct vm_area_struct *find_vma(struct m
 EXPORT_SYMBOL(find_vma);
 
 /*
- * find a VMA
- * - we don't extend stack VMAs under NOMMU conditions
- */
-struct vm_area_struct *find_extend_vma(struct mm_struct *mm, unsigned long addr)
-{
-	return find_vma(mm, addr);
-}
-
-/*
  * expand a stack to a given address
  * - not supported under NOMMU conditions
  */
-int expand_stack_locked(struct vm_area_struct *vma, unsigned long address,
-		bool write_locked)
+int expand_stack_locked(struct vm_area_struct *vma, unsigned long addr)
 {
 	return -ENOMEM;
 }
 
+struct vm_area_struct *expand_stack(struct mm_struct *mm, unsigned long addr)
+{
+	mmap_read_unlock(mm);
+	return NULL;
+}
+
 /*
  * look up the first VMA exactly that exactly matches addr
  * - should be called with mm->mmap_lock at least held readlocked
author maintainer
#26 lore raw

PATCH 24/29 gup: add warning if some caller would seem to want stack expansion

In reply to Greg Kroah-Hartman

From: Linus Torvalds <[email protected]>

commit a425ac5365f6cb3cc47bf83e6bff0213c10445f7 upstream.

It feels very unlikely that anybody would want to do a GUP in an unmapped area under the stack pointer, but real users sometimes do some really strange things. So add a (temporary) warning for the case where a GUP fails and expanding the stack might have made it work.

It's trivial to do the expansion in the caller as part of getting the mm lock in the first place - see __access_remote_vm() for ptrace, for example - it's just that it's unnecessarily painful to do it deep in the guts of the GUP lookup when we might have to drop and re-take the lock.

I doubt anybody actually does anything quite this strange, but let's be
proactive: adding these warnings is simple, and will make debugging it much easier if they trigger.

---
 mm/gup.c |   12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)
mm/gup.c +10 -2
@@ -1096,7 +1096,11 @@ static long __get_user_pages(struct mm_s
 
 		/* first iteration or cross vma bound */
 		if (!vma || start >= vma->vm_end) {
-			vma = vma_lookup(mm, start);
+			vma = find_vma(mm, start);
+			if (vma && (start < vma->vm_start)) {
+				WARN_ON_ONCE(vma->vm_flags & VM_GROWSDOWN);
+				vma = NULL;
+			}
 			if (!vma && in_gate_area(mm, start)) {
 				ret = get_gate_page(mm, start & PAGE_MASK,
 						gup_flags, &vma,
@@ -1265,9 +1269,13 @@ int fixup_user_fault(struct mm_struct *m
 		fault_flags |= FAULT_FLAG_ALLOW_RETRY | FAULT_FLAG_KILLABLE;
 
 retry:
-	vma = vma_lookup(mm, address);
+	vma = find_vma(mm, address);
 	if (!vma)
 		return -EFAULT;
+	if (address < vma->vm_start ) {
+		WARN_ON_ONCE(vma->vm_flags & VM_GROWSDOWN);
+		return -EFAULT;
+	}
 
 	if (!vma_permits_fault(vma, fault_flags))
 		return -EFAULT;
author maintainer
#27 lore raw

PATCH 25/29 fbdev: fix potential OOB read in fast_imageblit()

In reply to Greg Kroah-Hartman

From: Zhang Shurong <[email protected]>

commit c2d22806aecb24e2de55c30a06e5d6eb297d161d upstream.

There is a potential OOB read at fast_imageblit, for "colortab[(*src >> 4)]" can become a negative value due to "const char *s = image->data, *src".
This change makes sure the index for colortab always positive or zero.

Similar commit:
https://patchwork.kernel.org/patch/11746067

Potential bug report:
https://groups.google.com/g/syzkaller-bugs/c/9ubBXKeKXf4/m/k-QXy4UgAAAJ

---
 drivers/video/fbdev/core/sysimgblt.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/video/fbdev/core/sysimgblt.c +1 -1
@@ -189,7 +189,7 @@ static void fast_imageblit(const struct
 	u32 fgx = fgcolor, bgx = bgcolor, bpp = p->var.bits_per_pixel;
 	u32 ppw = 32/bpp, spitch = (image->width + 7)/8;
 	u32 bit_mask, eorx, shift;
-	const char *s = image->data, *src;
+	const u8 *s = image->data, *src;
 	u32 *dst;
 	const u32 *tab;
 	size_t tablen;
author maintainer
#28 lore raw

PATCH 26/29 HID: hidraw: fix data race on device refcount

In reply to Greg Kroah-Hartman

From: Ludvig Michaelsson <[email protected]>

commit 944ee77dc6ec7b0afd8ec70ffc418b238c92f12b upstream.

The hidraw_open() function increments the hidraw device reference counter. The counter has no dedicated synchronization mechanism, resulting in a potential data race when concurrently opening a device.

The race is a regression introduced by commit 8590222e4b02 ("HID:
hidraw: Replace hidraw device table mutex with a rwsem"). While minors_rwsem is intended to protect the hidraw_table itself, by instead acquiring the lock for writing, the reference counter is also protected. This is symmetrical to hidraw_release().

---
 drivers/hid/hidraw.c |    9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)
drivers/hid/hidraw.c +7 -2
@@ -272,7 +272,12 @@ static int hidraw_open(struct inode *ino
 		goto out;
 	}
 
-	down_read(&minors_rwsem);
+	/*
+	 * Technically not writing to the hidraw_table but a write lock is
+	 * required to protect the device refcount. This is symmetrical to
+	 * hidraw_release().
+	 */
+	down_write(&minors_rwsem);
 	if (!hidraw_table[minor] || !hidraw_table[minor]->exist) {
 		err = -ENODEV;
 		goto out_unlock;
@@ -301,7 +306,7 @@ static int hidraw_open(struct inode *ino
 	spin_unlock_irqrestore(&hidraw_table[minor]->list_lock, flags);
 	file->private_data = list;
 out_unlock:
-	up_read(&minors_rwsem);
+	up_write(&minors_rwsem);
 out:
 	if (err < 0)
 		kfree(list);
author maintainer
#29 lore raw

PATCH 27/29 HID: wacom: Use ktime_t rather than int when dealing with timestamps

In reply to Greg Kroah-Hartman

From: Jason Gerecke <[email protected]>

commit 9a6c0e28e215535b2938c61ded54603b4e5814c5 upstream.

Code which interacts with timestamps needs to use the ktime_t type returned by functions like ktime_get. The int type does not offer enough space to store these values, and attempting to use it is a recipe for problems. In this particular case, overflows would occur when calculating/storing timestamps leading to incorrect values being reported to userspace. In some cases these bad timestamps cause input handling in userspace to appear hung.

---
 drivers/hid/wacom_wac.c |    6 +++---
 drivers/hid/wacom_wac.h |    2 +-
 2 files changed, 4 insertions(+), 4 deletions(-)
drivers/hid/wacom_wac.c +3 -3
@@ -1309,7 +1309,7 @@ static void wacom_intuos_pro2_bt_pen(str
 	struct input_dev *pen_input = wacom->pen_input;
 	unsigned char *data = wacom->data;
 	int number_of_valid_frames = 0;
-	int time_interval = 15000000;
+	ktime_t time_interval = 15000000;
 	ktime_t time_packet_received = ktime_get();
 	int i;
 
@@ -1343,7 +1343,7 @@ static void wacom_intuos_pro2_bt_pen(str
 	if (number_of_valid_frames) {
 		if (wacom->hid_data.time_delayed)
 			time_interval = ktime_get() - wacom->hid_data.time_delayed;
-		time_interval /= number_of_valid_frames;
+		time_interval = div_u64(time_interval, number_of_valid_frames);
 		wacom->hid_data.time_delayed = time_packet_received;
 	}
 
@@ -1354,7 +1354,7 @@ static void wacom_intuos_pro2_bt_pen(str
 		bool range = frame[0] & 0x20;
 		bool invert = frame[0] & 0x10;
 		int frames_number_reversed = number_of_valid_frames - i - 1;
-		int event_timestamp = time_packet_received - frames_number_reversed * time_interval;
+		ktime_t event_timestamp = time_packet_received - frames_number_reversed * time_interval;
 
 		if (!valid)
 			continue;
drivers/hid/wacom_wac.h +1 -1
@@ -324,7 +324,7 @@ struct hid_data {
 	int ps_connected;
 	bool pad_input_event_flag;
 	unsigned short sequence_number;
-	int time_delayed;
+	ktime_t time_delayed;
 };
 
 struct wacom_remote_data {
author maintainer
#30 lore raw

PATCH 28/29 HID: logitech-hidpp: add HIDPP_QUIRK_DELAYED_INIT for the T651.

In reply to Greg Kroah-Hartman

From: Mike Hommey <[email protected]>

commit 5fe251112646d8626818ea90f7af325bab243efa upstream.

commit 498ba2069035 ("HID: logitech-hidpp: Don't restart communication if not necessary") put restarting communication behind that flag, and this was apparently necessary on the T651, but the flag was not set for it.

Fixes 498ba2069035 ("HID: logitech-hidpp: Don't restart communication if not necessary")
---
 drivers/hid/hid-logitech-hidpp.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/hid/hid-logitech-hidpp.c +1 -1
@@ -4364,7 +4364,7 @@ static const struct hid_device_id hidpp_
 	{ /* wireless touchpad T651 */
 	  HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_LOGITECH,
 		USB_DEVICE_ID_LOGITECH_T651),
-	  .driver_data = HIDPP_QUIRK_CLASS_WTP },
+	  .driver_data = HIDPP_QUIRK_CLASS_WTP | HIDPP_QUIRK_DELAYED_INIT },
 	{ /* Mouse Logitech Anywhere MX */
 	  LDJ_DEVICE(0x1017), .driver_data = HIDPP_QUIRK_HI_RES_SCROLL_1P0 },
 	{ /* Mouse logitech M560 */
author maintainer
#31 lore raw

PATCH 29/29 Revert "thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in mtk_thermal_probe"

In reply to Greg Kroah-Hartman

From: Ricardo Cañuelo <[email protected]>

commit 86edac7d3888c715fe3a81bd61f3617ecfe2e1dd upstream.

This reverts commit f05c7b7d9ea9477fcc388476c6f4ade8c66d2d26.

That change was causing a regression in the generic-adc-thermal-probed bootrr test as reported in the kernelci-results list [1].
A proper rework will take longer, so revert it for now.

[1] https://groups.io/g/kernelci-results/message/42660

Fixes f05c7b7d9ea9 ("thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in mtk_thermal_probe")
---
 drivers/thermal/mediatek/auxadc_thermal.c |   14 ++------------
 1 file changed, 2 insertions(+), 12 deletions(-)
drivers/thermal/mediatek/auxadc_thermal.c +2 -12
@@ -1142,12 +1142,7 @@ static int mtk_thermal_probe(struct plat
 		return -ENODEV;
 	}
 
-	auxadc_base = devm_of_iomap(&pdev->dev, auxadc, 0, NULL);
-	if (IS_ERR(auxadc_base)) {
-		of_node_put(auxadc);
-		return PTR_ERR(auxadc_base);
-	}
-
+	auxadc_base = of_iomap(auxadc, 0);
 	auxadc_phys_base = of_get_phys_base(auxadc);
 
 	of_node_put(auxadc);
@@ -1163,12 +1158,7 @@ static int mtk_thermal_probe(struct plat
 		return -ENODEV;
 	}
 
-	apmixed_base = devm_of_iomap(&pdev->dev, apmixedsys, 0, NULL);
-	if (IS_ERR(apmixed_base)) {
-		of_node_put(apmixedsys);
-		return PTR_ERR(apmixed_base);
-	}
-
+	apmixed_base = of_iomap(apmixedsys, 0);
 	apmixed_phys_base = of_get_phys_base(apmixedsys);
 
 	of_node_put(apmixedsys);
#32 lore raw
In reply to Greg Kroah-Hartman

Hello!

Early report of failures.

Arm64 fails with GCC-11 on the following configurations:
* lkftconfig
* lkftconfig-64k_page_size
* lkftconfig-debug
* lkftconfig-debug-kmemleak
* lkftconfig-kasan
* lkftconfig-kselftest
* lkftconfig-kunit
* lkftconfig-libgpiod
* lkftconfig-perf
* lkftconfig-rcutorture

lkftconfig is basically defconfig + a few fragments [1]. The suffixes mean that we're enabling a few other kconfigs.

Failure:
-----8<-----
/builds/linux/arch/arm64/mm/fault.c: In function 'do_page_fault':
/builds/linux/arch/arm64/mm/fault.c:576:9: error: 'vma' undeclared (first use in this function); did you mean 'vmap'?

  576 |         vma = lock_mm_and_find_vma(mm, addr, regs);
      |         ^~~
      |         vmap

/builds/linux/arch/arm64/mm/fault.c:576:9: note: each undeclared identifier is reported only once for each function it appears in /builds/linux/arch/arm64/mm/fault.c:579:17: error: label 'done' used but not defined

  579 |                 goto done;
      |                 ^~~~

make[4]: *** [/builds/linux/scripts/Makefile.build:252:
arch/arm64/mm/fault.o] Error 1
make[4]: Target 'arch/arm64/mm/' not remade because of errors. ----->8-----

We're expecting to see more failures on other architectures, and so will follow-up with that.

[1] https://github.com/Linaro/meta-lkft/tree/kirkstone/meta/recipes-kernel/linux/files

Greetings!

Daniel Díaz
[email protected]

Quoted 185 lines · Greg Kroah-Hartman

This is the start of the stable review cycle for the 6.3.11 release. There are 29 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Sat, 01 Jul 2023 18:41:39 +0000. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

        https://www.kernel.org/pub/linux/kernel/v6.x/stable-review/patch-6.3.11-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-6.3.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <[email protected]>

    Linux 6.3.11-rc1

Ricardo Cañuelo <[email protected]>
Revert "thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in mtk_thermal_probe"

Mike Hommey <[email protected]>
HID: logitech-hidpp: add HIDPP_QUIRK_DELAYED_INIT for the T651.

Jason Gerecke <[email protected]>
HID: wacom: Use ktime_t rather than int when dealing with timestamps

Ludvig Michaelsson <[email protected]>
HID: hidraw: fix data race on device refcount

Zhang Shurong <[email protected]>
fbdev: fix potential OOB read in fast_imageblit()

Linus Torvalds <[email protected]>
gup: add warning if some caller would seem to want stack expansion

Linus Torvalds <[email protected]>
mm: always expand the stack with the mmap write lock held

Linus Torvalds <[email protected]>
execve: expand new process stack manually ahead of time

Liam R. Howlett <[email protected]>
mm: make find_extend_vma() fail if write lock not held

Linus Torvalds <[email protected]>
powerpc/mm: convert coprocessor fault to lock_mm_and_find_vma()

Linus Torvalds <[email protected]>
mm/fault: convert remaining simple cases to lock_mm_and_find_vma()

Ben Hutchings <[email protected]>
arm/mm: Convert to using lock_mm_and_find_vma()

Ben Hutchings <[email protected]>
riscv/mm: Convert to using lock_mm_and_find_vma()

Ben Hutchings <[email protected]>
mips/mm: Convert to using lock_mm_and_find_vma()

Michael Ellerman <[email protected]>
powerpc/mm: Convert to using lock_mm_and_find_vma()

Linus Torvalds <[email protected]>
arm64/mm: Convert to using lock_mm_and_find_vma()

Linus Torvalds <[email protected]>
mm: make the page fault mmap locking killable

Linus Torvalds <[email protected]>
mm: introduce new 'lock_mm_and_find_vma()' page fault helper

Peng Zhang <[email protected]>
maple_tree: fix potential out-of-bounds access in mas_wr_end_piv()

Oliver Hartkopp <[email protected]>
can: isotp: isotp_sendmsg(): fix return error fix on TX path

Wyes Karny <[email protected]>
cpufreq: amd-pstate: Make amd-pstate EPP driver name hyphenated

Thomas Gleixner <[email protected]>
x86/smp: Cure kexec() vs. mwait_play_dead() breakage

Thomas Gleixner <[email protected]>
x86/smp: Use dedicated cache-line for mwait_play_dead()

Thomas Gleixner <[email protected]>
x86/smp: Remove pointless wmb()s from native_stop_other_cpus()

Tony Battersby <[email protected]>
x86/smp: Dont access non-existing CPUID leaf

Thomas Gleixner <[email protected]>
x86/smp: Make stop_other_cpus() more robust

Borislav Petkov (AMD) <[email protected]>
x86/microcode/AMD: Load late on both threads too

David Woodhouse <[email protected]>
mm/mmap: Fix error return in do_vmi_align_munmap()

Liam R. Howlett <[email protected]>
mm/mmap: Fix error path in do_vmi_align_munmap()

-------------

Diffstat:

 Makefile                                  |   4 +-
 arch/alpha/Kconfig                        |   1 +
 arch/alpha/mm/fault.c                     |  13 +--
 arch/arc/Kconfig                          |   1 +
 arch/arc/mm/fault.c                       |  11 +--
 arch/arm/Kconfig                          |   1 +
 arch/arm/mm/fault.c                       |  63 +++---------
 arch/arm64/Kconfig                        |   1 +
 arch/arm64/mm/fault.c                     |  44 ++-------
 arch/csky/Kconfig                         |   1 +
 arch/csky/mm/fault.c                      |  22 +----
 arch/hexagon/Kconfig                      |   1 +
 arch/hexagon/mm/vm_fault.c                |  18 +---
 arch/ia64/mm/fault.c                      |  36 ++-----
 arch/loongarch/Kconfig                    |   1 +
 arch/loongarch/mm/fault.c                 |  16 ++--
 arch/m68k/mm/fault.c                      |   9 +-
 arch/microblaze/mm/fault.c                |   5 +-
 arch/mips/Kconfig                         |   1 +
 arch/mips/mm/fault.c                      |  12 +--
 arch/nios2/Kconfig                        |   1 +
 arch/nios2/mm/fault.c                     |  17 +---
 arch/openrisc/mm/fault.c                  |   5 +-
 arch/parisc/mm/fault.c                    |  23 +++--
 arch/powerpc/Kconfig                      |   1 +
 arch/powerpc/mm/copro_fault.c             |  14 +--
 arch/powerpc/mm/fault.c                   |  39 +-------
 arch/riscv/Kconfig                        |   1 +
 arch/riscv/mm/fault.c                     |  31 +++---
 arch/s390/mm/fault.c                      |   5 +-
 arch/sh/Kconfig                           |   1 +
 arch/sh/mm/fault.c                        |  17 +---
 arch/sparc/Kconfig                        |   1 +
 arch/sparc/mm/fault_32.c                  |  32 ++-----
 arch/sparc/mm/fault_64.c                  |   8 +-
 arch/um/kernel/trap.c                     |  11 ++-
 arch/x86/Kconfig                          |   1 +
 arch/x86/include/asm/cpu.h                |   2 +
 arch/x86/include/asm/smp.h                |   2 +
 arch/x86/kernel/cpu/microcode/amd.c       |   2 +-
 arch/x86/kernel/process.c                 |  28 +++++-
 arch/x86/kernel/smp.c                     |  73 ++++++++------
 arch/x86/kernel/smpboot.c                 |  81 ++++++++++++++--
 arch/x86/mm/fault.c                       |  52 +---------
 arch/xtensa/Kconfig                       |   1 +
 arch/xtensa/mm/fault.c                    |  14 +--
 drivers/cpufreq/amd-pstate.c              |   2 +-
 drivers/hid/hid-logitech-hidpp.c          |   2 +-
 drivers/hid/hidraw.c                      |   9 +-
 drivers/hid/wacom_wac.c                   |   6 +-
 drivers/hid/wacom_wac.h                   |   2 +-
 drivers/iommu/amd/iommu_v2.c              |   4 +-
 drivers/iommu/iommu-sva.c                 |   2 +-
 drivers/thermal/mediatek/auxadc_thermal.c |  14 +--
 drivers/video/fbdev/core/sysimgblt.c      |   2 +-
 fs/binfmt_elf.c                           |   6 +-
 fs/exec.c                                 |  38 ++++----
 include/linux/mm.h                        |  16 ++--
 lib/maple_tree.c                          |  11 ++-
 mm/Kconfig                                |   4 +
 mm/gup.c                                  |  14 ++-
 mm/memory.c                               | 127 +++++++++++++++++++++++++
 mm/mmap.c                                 | 153 +++++++++++++++++++++++-------
 mm/nommu.c                                |  17 ++--
 net/can/isotp.c                           |   5 +-
 65 files changed, 614 insertions(+), 544 deletions(-)
author maintainer
#33 lore raw
Quoted 31 lines · Daniel Díaz

Hello!

Early report of failures.

Arm64 fails with GCC-11 on the following configurations:
* lkftconfig
* lkftconfig-64k_page_size
* lkftconfig-debug
* lkftconfig-debug-kmemleak
* lkftconfig-kasan
* lkftconfig-kselftest
* lkftconfig-kunit
* lkftconfig-libgpiod
* lkftconfig-perf
* lkftconfig-rcutorture

lkftconfig is basically defconfig + a few fragments [1]. The suffixes mean that we're enabling a few other kconfigs.

Failure:
-----8<-----
/builds/linux/arch/arm64/mm/fault.c: In function 'do_page_fault':
/builds/linux/arch/arm64/mm/fault.c:576:9: error: 'vma' undeclared (first use in this function); did you mean 'vmap'?

  576 |         vma = lock_mm_and_find_vma(mm, addr, regs);
      |         ^~~
      |         vmap

/builds/linux/arch/arm64/mm/fault.c:576:9: note: each undeclared identifier is reported only once for each function it appears in /builds/linux/arch/arm64/mm/fault.c:579:17: error: label 'done' used but not defined

Quoted 6 lines
  579 |                 goto done;
      |                 ^~~~

make[4]: *** [/builds/linux/scripts/Makefile.build:252:
arch/arm64/mm/fault.o] Error 1
make[4]: Target 'arch/arm64/mm/' not remade because of errors. ----->8-----

Is this also failing in Linus's tree?

thanks,

greg k-h

#34 lore raw

Hello!

Quoted 39 lines · Greg Kroah-Hartman
Quoted 31 lines · Daniel Díaz

Hello!

Early report of failures.

Arm64 fails with GCC-11 on the following configurations:
* lkftconfig
* lkftconfig-64k_page_size
* lkftconfig-debug
* lkftconfig-debug-kmemleak
* lkftconfig-kasan
* lkftconfig-kselftest
* lkftconfig-kunit
* lkftconfig-libgpiod
* lkftconfig-perf
* lkftconfig-rcutorture

lkftconfig is basically defconfig + a few fragments [1]. The suffixes mean that we're enabling a few other kconfigs.

Failure:
-----8<-----
/builds/linux/arch/arm64/mm/fault.c: In function 'do_page_fault':
/builds/linux/arch/arm64/mm/fault.c:576:9: error: 'vma' undeclared (first use in this function); did you mean 'vmap'?

  576 |         vma = lock_mm_and_find_vma(mm, addr, regs);
      |         ^~~
      |         vmap

/builds/linux/arch/arm64/mm/fault.c:576:9: note: each undeclared identifier is reported only once for each function it appears in /builds/linux/arch/arm64/mm/fault.c:579:17: error: label 'done' used but not defined

Quoted 6 lines
  579 |                 goto done;
      |                 ^~~~

make[4]: *** [/builds/linux/scripts/Makefile.build:252:
arch/arm64/mm/fault.o] Error 1
make[4]: Target 'arch/arm64/mm/' not remade because of errors. ----->8-----

Quoted 1 line

Is this also failing in Linus's tree?

(Sorry for the previous top-post.)

No, only here on 6.3.

Greetings!

Daniel Díaz
[email protected]

author maintainer
#35 lore raw
Quoted 43 lines · Daniel Díaz

Hello!

Quoted 39 lines · Greg Kroah-Hartman
Quoted 37 lines · Daniel Díaz

Hello!

Early report of failures.

Arm64 fails with GCC-11 on the following configurations:
* lkftconfig
* lkftconfig-64k_page_size
* lkftconfig-debug
* lkftconfig-debug-kmemleak
* lkftconfig-kasan
* lkftconfig-kselftest
* lkftconfig-kunit
* lkftconfig-libgpiod
* lkftconfig-perf
* lkftconfig-rcutorture

lkftconfig is basically defconfig + a few fragments [1]. The suffixes mean that we're enabling a few other kconfigs.

Failure:
-----8<-----
/builds/linux/arch/arm64/mm/fault.c: In function 'do_page_fault':
/builds/linux/arch/arm64/mm/fault.c:576:9: error: 'vma' undeclared (first use in this function); did you mean 'vmap'?

  576 |         vma = lock_mm_and_find_vma(mm, addr, regs);
      |         ^~~
      |         vmap

/builds/linux/arch/arm64/mm/fault.c:576:9: note: each undeclared identifier is reported only once for each function it appears in /builds/linux/arch/arm64/mm/fault.c:579:17: error: label 'done' used but not defined

  579 |                 goto done;
      |                 ^~~~

make[4]: *** [/builds/linux/scripts/Makefile.build:252:
arch/arm64/mm/fault.o] Error 1
make[4]: Target 'arch/arm64/mm/' not remade because of errors. ----->8-----

Quoted 5 lines
Quoted 1 line

Is this also failing in Linus's tree?

(Sorry for the previous top-post.)

No, only here on 6.3.

Ok, found the problem, will push out a -rc2 now, thanks for the quick notice!

greg k-h