Skip to contentSkip to conversation

octeontx2-pf: Add additional check for MCAM rules

PATCH Superseded Suman Ghosh 2 participants 2 messages Jul 6, 2023 – Jul 11, 2023

Subsystems (3)

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

PATCH v4 1/1 octeontx2-pf: Add additional check for MCAM rules

Due to hardware limitation, MCAM drop rule with
ether_type == 802.1Q and vlan_id == 0 is not supported. Hence rejecting such rules.

Fixes dce677da57c0 ("octeontx2-pf: Add vlan-etype to ntuple filters")

---
Changes since v3:
- moved assignment of vlan_etype before the if check

 .../net/ethernet/marvell/octeontx2/nic/otx2_flows.c |  8 ++++++++
 .../net/ethernet/marvell/octeontx2/nic/otx2_tc.c    | 13 +++++++++++++
 2 files changed, 21 insertions(+)
drivers/net/ethernet/marvell/octeontx2/nic/otx2_flows.c +8 -0
index 10e11262d48a..2d7713a1a153 100644
@@ -872,6 +872,14 @@ static int otx2_prepare_flow_request(struct ethtool_rx_flow_spec *fsp,
 				return -EINVAL;
 
 			vlan_etype = be16_to_cpu(fsp->h_ext.vlan_etype);
+
+			/* Drop rule with vlan_etype == 802.1Q
+			 * and vlan_id == 0 is not supported
+			 */
+			if (vlan_etype == ETH_P_8021Q && !fsp->m_ext.vlan_tci &&
+			    fsp->ring_cookie == RX_CLS_FLOW_DISC)
+				return -EINVAL;
+
 			/* Only ETH_P_8021Q and ETH_P_802AD types supported */
 			if (vlan_etype != ETH_P_8021Q &&
 			    vlan_etype != ETH_P_8021AD)
drivers/net/ethernet/marvell/octeontx2/nic/otx2_tc.c +13 -0
index 044cc211424e..6c0fdc2bad73 100644
@@ -604,6 +604,19 @@ static int otx2_tc_prepare_flow(struct otx2_nic *nic, struct otx2_tc_flow *node,
 			return -EOPNOTSUPP;
 		}
 
+		if (!match.mask->vlan_id) {
+			struct flow_action_entry *act;
+			int i;
+
+			flow_action_for_each(i, act, &rule->action) {
+				if (act->id == FLOW_ACTION_DROP) {
+					netdev_err(nic->netdev, "vlan tpid 0x%x with vlan_id %d is not supported for DROP rule.\n",
+						   ntohs(match.key->vlan_tpid), match.key->vlan_id);
+					return -EOPNOTSUPP;
+				}
+			}
+		}
+
 		if (match.mask->vlan_id ||
 		    match.mask->vlan_dei ||
 		    match.mask->vlan_priority) {
Signature · 1 line
2.25.1
#1 lore raw
Quoted 9 lines · Suman Ghosh

Due to hardware limitation, MCAM drop rule with
ether_type == 802.1Q and vlan_id == 0 is not supported. Hence rejecting such rules.

Fixes dce677da57c0 ("octeontx2-pf: Add vlan-etype to ntuple filters")

---
Changes since v3:
- moved assignment of vlan_etype before the if check

And what were changes in previous versions?

Also you should write the target net or net-next in the patch subject.

Thanks