platform/x86: Add SEL-3350 platform driver
PATCH v2 1/1 platform/x86: Add SEL-3350 platform driver
Add a driver for Schweitzer Engineering Laboratories SEL-3350 computers front LEDs and power supplies. LED and power supply status is provided by the Intel SoC GPIO.
---
Changes in v2:
- Adjust Kconfig to depend on GPIOLIB rather than select. This required moving PINCTRL_BROXTON to depend on as well to avoid dependency errors.
- Move power_supply_config structs to the stack in probe and use one struct for both power supplies
- Remove assignement of of_node since it is already NULL
drivers/platform/x86/Kconfig | 15 ++ drivers/platform/x86/Makefile | 3 + drivers/platform/x86/sel3350-platform.c | 251 ++++++++++++++++++++++++ 3 files changed, 269 insertions(+) create mode 100644 drivers/platform/x86/sel3350-platform.c
drivers/platform/x86/Kconfig +15 -0
@@ -1094,6 +1094,21 @@ config WINMATE_FM07_KEYS buttons below the display. This module adds an input device that delivers key events when these buttons are pressed. +config SEL3350_PLATFORM + tristate "SEL-3350 LEDs and power supplies" + depends on ACPI + depends on GPIOLIB + depends on PINCTRL_BROXTON + select POWER_SUPPLY + select NEW_LEDS + select LEDS_CLASS + select LEDS_GPIO + help + Support for LEDs and power supplies on SEL-3350 computers. + + To compile this driver as a module, choose M here: the module + will be called sel3350-platform. + endif # X86_PLATFORM_DEVICES config P2SB
drivers/platform/x86/Makefile +3 -0
@@ -135,3 +135,6 @@ obj-$(CONFIG_SIEMENS_SIMATIC_IPC) += simatic-ipc.o # Winmate obj-$(CONFIG_WINMATE_FM07_KEYS) += winmate-fm07-keys.o + +# SEL +obj-$(CONFIG_SEL3350_PLATFORM) += sel3350-platform.o
drivers/platform/x86/sel3350-platform.c new file +251 -0
251 lines not on this page · raw message
Signature · 1 line
2.41.0
Hi,
Quoted 7 lines · Robert Joslyn
Add a driver for Schweitzer Engineering Laboratories SEL-3350 computers front LEDs and power supplies. LED and power supply status is provided by the Intel SoC GPIO.
Signed-off-by Robert Joslyn <[email protected]>---
Quoted 7 lines
Changes in v2:
- AdjustKconfigto depend on GPIOLIB rather than select. This required movingPINCTRL_BROXTONto depend on as well to avoid dependency errors.
- Movepower_supply_configstructs to the stack in probe and use one struct for both power supplies
- Remove assignement ofof_nodesince it is already NULL
Thank you for your patch, I've applied this patch to my review-hans branch:
https://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86.git/log/?h=review-hans
Once I've run some tests on this branch the patches there will be added to the platform-drivers-x86/for-next branch and eventually will be included in the pdx86 pull-request to Linus for the next merge-window.
Regards,
Hans
Quoted 301 lines
drivers/platform/x86/Kconfig | 15 ++ drivers/platform/x86/Makefile | 3 + drivers/platform/x86/sel3350-platform.c | 251 ++++++++++++++++++++++++ 3 files changed, 269 insertions(+) create mode 100644 drivers/platform/x86/sel3350-platform.cdrivers/platform/x86/Kconfig +15
-0@@ -1094,6 +1094,21 @@ config WINMATE_FM07_KEYS buttons below the display. This module adds an input device that delivers key events when these buttons are pressed. +config SEL3350_PLATFORM + tristate "SEL-3350 LEDs and power supplies" + depends on ACPI + depends on GPIOLIB + depends on PINCTRL_BROXTON + select POWER_SUPPLY + select NEW_LEDS + select LEDS_CLASS + select LEDS_GPIO + help + Support for LEDs and power supplies on SEL-3350 computers. + + To compile this driver as a module, choose M here: the module + will be called sel3350-platform. + endif # X86_PLATFORM_DEVICES config P2SBdrivers/platform/x86/Makefile +3
-0@@ -135,3 +135,6 @@ obj-$(CONFIG_SIEMENS_SIMATIC_IPC) += simatic-ipc.o # Winmate obj-$(CONFIG_WINMATE_FM07_KEYS) += winmate-fm07-keys.o + +# SEL +obj-$(CONFIG_SEL3350_PLATFORM) += sel3350-platform.odrivers/platform/x86/sel3350-platform.c new file +251
-0@@ -0,0 +1,251 @@ +// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause +/* +* Copyright 2023 Schweitzer Engineering Laboratories, Inc. +* 2350 NE Hopkins Court, Pullman, WA 99163 USA +* +* Platform support for the b2093 mainboard used in SEL-3350 computers. +* Consumes GPIO from the SoC to provide standard LED and power supply +* devices. +*/ + +#include <linux/acpi.h> +#include <linux/gpio/consumer.h> +#include <linux/gpio/machine.h> +#include <linux/leds.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/power_supply.h> + +/* Broxton communities */ +#define BXT_NW "INT3452:01" +#define BXT_W "INT3452:02" +#define BXT_SW "INT3452:03" + +#define B2093_GPIO_ACPI_ID "SEL0003" + +#define SEL_PS_A "sel_ps_a" +#define SEL_PS_A_DETECT "sel_ps_a_detect" +#define SEL_PS_A_GOOD "sel_ps_a_good" +#define SEL_PS_B "sel_ps_b" +#define SEL_PS_B_DETECT "sel_ps_b_detect" +#define SEL_PS_B_GOOD "sel_ps_b_good" + +/* LEDs */ +static const struct gpio_led sel3350_leds[] = { + { .name ="sel:green:aux1" }, + { .name ="sel:green:aux2" }, + { .name ="sel:green:aux3" }, + { .name ="sel:green:aux4" }, + { .name ="sel:red:alarm" }, + { .name ="sel:green:enabled" , + .default_state =LEDS_GPIO_DEFSTATE_ON }, + { .name ="sel:red:aux1" }, + { .name ="sel:red:aux2" }, + { .name ="sel:red:aux3" }, + { .name ="sel:red:aux4" }, +}; + +static const struct gpio_led_platform_data sel3350_leds_pdata = { + .num_leds =ARRAY_SIZE (sel3350_leds), + .leds = sel3350_leds, +}; + +/* Map GPIOs to LEDs */ +static struct gpiod_lookup_table sel3350_leds_table = { + .dev_id ="leds-gpio" , + .table = { +GPIO_LOOKUP_IDX (BXT_NW ,49 ,NULL ,0 ,GPIO_ACTIVE_HIGH ), +GPIO_LOOKUP_IDX (BXT_NW ,50 ,NULL ,1 ,GPIO_ACTIVE_HIGH ), +GPIO_LOOKUP_IDX (BXT_NW ,51 ,NULL ,2 ,GPIO_ACTIVE_HIGH ), +GPIO_LOOKUP_IDX (BXT_NW ,52 ,NULL ,3 ,GPIO_ACTIVE_HIGH ), +GPIO_LOOKUP_IDX (BXT_W ,20 ,NULL ,4 ,GPIO_ACTIVE_HIGH ), +GPIO_LOOKUP_IDX (BXT_W ,21 ,NULL ,5 ,GPIO_ACTIVE_HIGH ), +GPIO_LOOKUP_IDX (BXT_SW ,37 ,NULL ,6 ,GPIO_ACTIVE_HIGH ), +GPIO_LOOKUP_IDX (BXT_SW ,38 ,NULL ,7 ,GPIO_ACTIVE_HIGH ), +GPIO_LOOKUP_IDX (BXT_SW ,39 ,NULL ,8 ,GPIO_ACTIVE_HIGH ), +GPIO_LOOKUP_IDX (BXT_SW ,40 ,NULL ,9 ,GPIO_ACTIVE_HIGH ), + {}, + } +}; + +/* Map GPIOs to power supplies */ +static struct gpiod_lookup_table sel3350_gpios_table = { + .dev_id =B2093_GPIO_ACPI_ID ":00" , + .table = { +GPIO_LOOKUP (BXT_NW ,44 ,SEL_PS_A_DETECT ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP (BXT_NW ,45 ,SEL_PS_A_GOOD ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP (BXT_NW ,46 ,SEL_PS_B_DETECT ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP (BXT_NW ,47 ,SEL_PS_B_GOOD ,GPIO_ACTIVE_LOW ), + {}, + } +}; + +/* Power Supplies */ + +struct sel3350_power_cfg_data { +struct gpio_desc *ps_detect; +struct gpio_desc *ps_good; +}; + +static int sel3350_power_get_property (struct power_supply *psy, +enum power_supply_property psp, +union power_supply_propval *val) +{ +struct sel3350_power_cfg_data *data =power_supply_get_drvdata (psy); + +switch (psp) { +case POWER_SUPPLY_PROP_HEALTH : +if (gpiod_get_value (data->ps_detect)) { +if (gpiod_get_value (data->ps_good)) + val->intval =POWER_SUPPLY_HEALTH_GOOD ; +else + val->intval =POWER_SUPPLY_HEALTH_UNSPEC_FAILURE ; + }else { + val->intval =POWER_SUPPLY_HEALTH_UNKNOWN ; + } +break ; +case POWER_SUPPLY_PROP_PRESENT : + val->intval =gpiod_get_value (data->ps_detect); +break ; +case POWER_SUPPLY_PROP_ONLINE : + val->intval =gpiod_get_value (data->ps_good); +break ; +default : +return -EINVAL ; + } +return 0 ; +} + +static const enum power_supply_property sel3350_power_properties[] = { +POWER_SUPPLY_PROP_HEALTH , +POWER_SUPPLY_PROP_PRESENT , +POWER_SUPPLY_PROP_ONLINE , +}; + +static const struct power_supply_desc sel3350_ps_a_desc = { + .name =SEL_PS_A , + .type =POWER_SUPPLY_TYPE_MAINS , + .properties = sel3350_power_properties, + .num_properties =ARRAY_SIZE (sel3350_power_properties), + .get_property = sel3350_power_get_property, +}; + +static const struct power_supply_desc sel3350_ps_b_desc = { + .name =SEL_PS_B , + .type =POWER_SUPPLY_TYPE_MAINS , + .properties = sel3350_power_properties, + .num_properties =ARRAY_SIZE (sel3350_power_properties), + .get_property = sel3350_power_get_property, +}; + +struct sel3350_data { +struct platform_device *leds_pdev; +struct power_supply *ps_a; +struct power_supply *ps_b; +struct sel3350_power_cfg_data ps_a_cfg_data; +struct sel3350_power_cfg_data ps_b_cfg_data; +}; + +static int sel3350_probe (struct platform_device *pdev) +{ +int rs; +struct sel3350_data *sel3350; +struct power_supply_config ps_cfg = {}; + + sel3350 =devm_kzalloc (&pdev->dev,sizeof (struct sel3350_data ),GFP_KERNEL ); +if (!sel3350) +return -ENOMEM ; + +platform_set_drvdata (pdev, sel3350); + +gpiod_add_lookup_table (&sel3350_leds_table); +gpiod_add_lookup_table (&sel3350_gpios_table); + + sel3350->leds_pdev =platform_device_register_data ( +NULL , +"leds-gpio" , +PLATFORM_DEVID_NONE , + &sel3350_leds_pdata, +sizeof (sel3350_leds_pdata)); +if (IS_ERR (sel3350->leds_pdev)) { + rs =PTR_ERR (sel3350->leds_pdev); +dev_err (&pdev->dev,"Failed registering platform device: %d\n" , rs); + goto err_platform; + } + +/* Power Supply A */ + sel3350->ps_a_cfg_data.ps_detect =devm_gpiod_get (&pdev->dev, +SEL_PS_A_DETECT , +GPIOD_IN ); + sel3350->ps_a_cfg_data.ps_good =devm_gpiod_get (&pdev->dev, +SEL_PS_A_GOOD , +GPIOD_IN ); + ps_cfg.drv_data = &sel3350->ps_a_cfg_data; + sel3350->ps_a =devm_power_supply_register (&pdev->dev, + &sel3350_ps_a_desc, + &ps_cfg); +if (IS_ERR (sel3350->ps_a)) { + rs =PTR_ERR (sel3350->ps_a); +dev_err (&pdev->dev,"Failed registering power supply A: %d\n" , rs); + goto err_ps; + } + +/* Power Supply B */ + sel3350->ps_b_cfg_data.ps_detect =devm_gpiod_get (&pdev->dev, +SEL_PS_B_DETECT , +GPIOD_IN ); + sel3350->ps_b_cfg_data.ps_good =devm_gpiod_get (&pdev->dev, +SEL_PS_B_GOOD , +GPIOD_IN ); + ps_cfg.drv_data = &sel3350->ps_b_cfg_data; + sel3350->ps_b =devm_power_supply_register (&pdev->dev, + &sel3350_ps_b_desc, + &ps_cfg); +if (IS_ERR (sel3350->ps_b)) { + rs =PTR_ERR (sel3350->ps_b); +dev_err (&pdev->dev,"Failed registering power supply B: %d\n" , rs); + goto err_ps; + } + +return 0 ; + +err_ps: +platform_device_unregister (sel3350->leds_pdev); +err_platform: +gpiod_remove_lookup_table (&sel3350_gpios_table); +gpiod_remove_lookup_table (&sel3350_leds_table); + +return rs; +} + +static int sel3350_remove (struct platform_device *pdev) +{ +struct sel3350_data *sel3350 =platform_get_drvdata (pdev); + +platform_device_unregister (sel3350->leds_pdev); +gpiod_remove_lookup_table (&sel3350_gpios_table); +gpiod_remove_lookup_table (&sel3350_leds_table); + +return 0 ; +} + +static const struct acpi_device_id sel3350_device_ids[] = { + {B2093_GPIO_ACPI_ID ,0 }, + {"" ,0 }, +}; +MODULE_DEVICE_TABLE (acpi, sel3350_device_ids); + +static struct platform_driver sel3350_platform_driver = { + .probe = sel3350_probe, + .remove = sel3350_remove, + .driver = { + .name ="sel3350-platform" , + .acpi_match_table = sel3350_device_ids, + }, +}; +module_platform_driver (sel3350_platform_driver); + +MODULE_AUTHOR ("Schweitzer Engineering Laboratories" ); +MODULE_DESCRIPTION ("SEL-3350 platform driver" ); +MODULE_LICENSE ("Dual BSD/GPL" ); +MODULE_SOFTDEP ("pre: pinctrl_broxton leds-gpio" );