phy: Add support for the Apple Type-C PHY
Subsystems (2)
PATCH 1/1 phy: Add support for the Apple Type-C PHY
This is merely a dummy driver that makes sure the DWC3 XHCI driver finds its reset and PHY controllers. We rely on iBoot to set up the PHY for us.
Signed-off-by Mark Kettenis <[email protected]>
--- MAINTAINERS | 1 + arch/arm/Kconfig | 1 + configs/apple_m1_defconfig | 1 + drivers/phy/Kconfig | 10 +++++++ drivers/phy/Makefile | 1 + drivers/phy/phy-apple-atc.c | 56 +++++++++++++++++++++++++++++++++++++ 6 files changed, 70 insertions(+) create mode 100644 drivers/phy/phy-apple-atc.c
MAINTAINERS +1 -0
@@ -123,6 +123,7 @@ F: configs/apple_m1_defconfig F: drivers/iommu/apple_dart.c F: drivers/nvme/nvme_apple.c F: drivers/pci/pcie_apple.c +F: drivers/phy/phy-apple-atc.c F: drivers/pinctrl/pinctrl-apple.c F: drivers/watchdog/apple_wdt.c F: include/configs/apple.h
arch/arm/Kconfig +1 -0
@@ -1011,6 +1011,7 @@ config ARCH_APPLE select OF_BOARD_SETUP select OF_CONTROL select PCI + select PHY select PINCTRL select POSITION_INDEPENDENT select POWER_DOMAIN
configs/apple_m1_defconfig +1 -0
@@ -16,6 +16,7 @@ CONFIG_NVME_APPLE=y CONFIG_USB_XHCI_HCD=y CONFIG_USB_XHCI_DWC3=y CONFIG_USB_XHCI_PCI=y +CONFIG_USB_DWC3=y CONFIG_USB_KEYBOARD=y CONFIG_SYS_WHITE_ON_BLACK=y CONFIG_NO_FB_CLEAR=y
drivers/phy/Kconfig +10 -0
@@ -70,6 +70,16 @@ config AB8500_USB_PHY help Support for the USB OTG PHY in ST-Ericsson AB8500. +config APPLE_ATCPHY + bool "Apple Type-C PHY Driver" + depends on PHY && ARCH_APPLE + default y + help + Support for the Apple Type-C PHY. + + This is a dummy driver since the PHY is initialized + sufficiently by previous stage firmware. + config BCM6318_USBH_PHY bool "BCM6318 USBH PHY support" depends on PHY && ARCH_BMIPS
drivers/phy/Makefile +1 -0
@@ -12,6 +12,7 @@ obj-$(CONFIG_$(SPL_)PHY) += phy-uclass.o obj-$(CONFIG_$(SPL_)NOP_PHY) += nop-phy.o obj-$(CONFIG_MIPI_DPHY_HELPERS) += phy-core-mipi-dphy.o obj-$(CONFIG_AB8500_USB_PHY) += phy-ab8500-usb.o +obj-$(CONFIG_APPLE_ATCPHY) += phy-apple-atc.o obj-$(CONFIG_BCM6318_USBH_PHY) += bcm6318-usbh-phy.o obj-$(CONFIG_BCM6348_USBH_PHY) += bcm6348-usbh-phy.o obj-$(CONFIG_BCM6358_USBH_PHY) += bcm6358-usbh-phy.o
drivers/phy/phy-apple-atc.c new file +56 -0
56 lines not on this page · raw message
Signature · 1 line
2.41.0
Quoted 5 lines · Mark Kettenis
This is merely a dummy driver that makes sure the DWC3 XHCI driver finds its reset and PHY controllers. We rely on iBoot to set up the PHY for us.
Signed-off-by Mark Kettenis <[email protected]>
Applied to u-boot/next, thanks!
Signature · 1 line
Tom