arm64: dts: imx8mn-evk: Add HDMI support
Subsystems (2)
Fabio Estevam
reviewerPATCH 1/2 arm64: dts: imx8mn-evk: Add HDMI support
From: Fabio Estevam <[email protected]>
imx8mn-evk has a MIPI DSI port that can be used with a ADV7535 MIPI DSI to HDMI bridge.
Add support for it.
--- arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi | 67 +++++++++++++++++++ 1 file changed, 67 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi +67 -0
@@ -23,6 +23,18 @@ status { }; }; + hdmi-connector { + compatible = "hdmi-connector"; + label = "hdmi"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&adv7533_out>; + }; + }; + }; + memory@40000000 { device_type = "memory"; reg = <0x0 0x40000000 0 0x80000000>;
@@ -167,6 +179,41 @@ &i2c2 { sda-gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>; status = "okay"; + hdmi@3d { + compatible = "adi,adv7535"; + reg = <0x3d>, <0x3c>, <0x3e>, <0x3f>; + reg-names = "main", "cec", "edid", "packet"; + adi,dsi-lanes = <4>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + adv7533_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + + port@1 { + reg = <1>; + + adv7533_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + + }; + }; + ptn5110: tcpc@50 { compatible = "nxp,ptn5110"; pinctrl-names = "default";
@@ -214,6 +261,26 @@ pca6416: gpio@20 { }; }; +&lcdif { + status = "okay"; +}; + +&mipi_dsi { + samsung,esc-clock-frequency = <10000000>; + status = "okay"; + + ports { + port@1 { + reg = <1>; + + dsi_out: endpoint { + remote-endpoint = <&adv7533_in>; + data-lanes = <1 2 3 4>; + }; + }; + }; +}; + &sai2 { #sound-dai-cells = <0>; pinctrl-names = "default";
Signature · 7 lines
2.34.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Fabio Estevam
reviewerPATCH 2/2 arm64: dts: imx8mn-evk: Add camera support
From: Fabio Estevam <[email protected]>
Add support for the OV5640 camera.
Tested with the following commands:
media-ctl -l "'ov5640 2-003c':0 -> 'csis-32e30000.mipi-csi':0 [1]"
media-ctl -V "'ov5640 2-003c':0 [fmt:UYVY8_1X16/640x480 field:none]"
media-ctl -V "'crossbar':0 [fmt:UYVY8_1X16/640x480 field:none]"
media-ctl -V "'mxc_isi.0':0 [fmt:UYVY8_1X16/640x480 field:none]"
v4l2-ctl --device /dev/video0 --set-fmt-video=width=640,height=480,pixelformat=YUYV v4l2-ctl --stream-mmap -d /dev/video0;
gst-launch-1.0 -v v4l2src device=/dev/video0 ! video/x-raw,width=640,height=480 ! waylandsink
--- arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi | 47 +++++++++++++++++++ 1 file changed, 47 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi +47 -0
@@ -259,6 +259,45 @@ pca6416: gpio@20 { gpio-controller; #gpio-cells = <2>; }; + + camera@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_camera>; + clocks = <&clk IMX8MN_CLK_CLKO1>; + clock-names = "xclk"; + assigned-clocks = <&clk IMX8MN_CLK_CLKO1>; + assigned-clock-parents = <&clk IMX8MN_CLK_24M>; + assigned-clock-rates = <24000000>; + powerdown-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + + port { + ov5640_to_mipi_csi2: endpoint { + remote-endpoint = <&imx8mn_mipi_csi_in>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; +}; + +&isi { + status = "okay"; +}; + +&mipi_csi { + status = "okay"; + + ports { + port@0 { + imx8mn_mipi_csi_in: endpoint { + remote-endpoint = <&ov5640_to_mipi_csi2>; + data-lanes = <1 2>; + }; + }; + }; }; &lcdif {
@@ -393,6 +432,14 @@ &wdog1 { }; &iomuxc { + pinctrl_camera: cameragrp { + fsl,pins = < + MX8MN_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19 + MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 + MX8MN_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1 0x59 + >; + }; + pinctrl_fec1: fec1grp { fsl,pins = < MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x3
Signature · 7 lines
2.34.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Shawn Guo
AppliedQuoted 7 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
imx8mn-evk has a MIPI DSI port that can be used with a ADV7535 MIPI DSI to HDMI bridge.
Add support for it.
Signed-off-by Fabio Estevam <[email protected]>
Applied both, thanks!
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel