Skip to contentSkip to conversation

hwmon: (pmbus) Add ON_OFF_CONFIG register bits

PATCH In review Naresh Solanki 2 participants 7 messages Jul 27, 2023 – Aug 1, 2023 Hardware monitoring

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 hwmon: (pmbus) Add ON_OFF_CONFIG register bits

From: Patrick Rudolph <[email protected]>

Add bits found in the ON_OFF_CONFIG register.

---
 drivers/hwmon/pmbus/pmbus.h | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/hwmon/pmbus/pmbus.h +9 -0
index b0832a4c690d..7a28bac7f171 100644
@@ -243,6 +243,15 @@ enum pmbus_regs {
  */
 #define PB_OPERATION_CONTROL_ON		BIT(7)
 
+/*
+ * ON_OFF_CONFIG
+ */
+#define PB_ON_OFF_CONFIG_POWERUP_CONTROL	BIT(4)
+#define PB_ON_OFF_CONFIG_OPERATION_REQ		BIT(3)
+#define PB_ON_OFF_CONFIG_EN_PIN_REQ		BIT(2)
+#define PB_ON_OFF_CONFIG_POLARITY_HIGH		BIT(1)
+#define PB_ON_OFF_CONFIG_TURN_OFF_FAST		BIT(0)
+
 /*
  * WRITE_PROTECT
  */

base-commit: 60a6aa5742fa499a918b66d80c9baabef56c3adc

Signature · 1 line
2.41.0
#1 lore raw

PATCH v2 2/2 hwmon: (pmbus/tda38640) Add workaround for bug in SVID mode

From: Patrick Rudolph <[email protected]>

Introduce a workaround to handle the issue where the regulator cannot be enabled using BIT7 of the OPERATION(01h) register when in SVID mode.

It works when in PMBUS mode. In SVID mode the regulator only cares about the ENABLE pin.

Determine if chip is in SVID mode by checking BIT15 of MTP memory offset 0x44 as described in the datasheet.

If chip is in SVID mode then apply the workaround by
1. Determine EN pin level
2. Maps BIT7 of OPERATION(01h) to EN_PIN_POLARITY(BIT1) of PB_ON_OFF_CONFIG.

Tested working of TDA38640 in both SVID & PMBus mode.

----
Changes in V2:
- Remove dependency on DT propery,
- Runtime determine SVID mode & ENABLE pin level,
- Update commit message.

---
 drivers/hwmon/pmbus/tda38640.c | 151 ++++++++++++++++++++++++++++++++-
 1 file changed, 149 insertions(+), 2 deletions(-)
drivers/hwmon/pmbus/tda38640.c +149 -2
index 450b0273fb59..daaf77f8bf82 100644
@@ -18,6 +18,127 @@ static const struct regulator_desc __maybe_unused tda38640_reg_desc[] = {
 	PMBUS_REGULATOR("vout", 0),
 };
 
+struct tda38640_data {
+	struct pmbus_driver_info info;
+	u32 en_pin_lvl;
+};
+
+#define to_tda38640_data(x)  container_of(x, struct tda38640_data, info)
+
+/*
+ * Map PB_ON_OFF_CONFIG_POLARITY_HIGH to PB_OPERATION_CONTROL_ON.
+ */
+static int tda38640_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct tda38640_data *data = to_tda38640_data(info);
+	int ret, on_off_config, enabled;
+
+	if (reg != PMBUS_OPERATION)
+		return -ENODATA;
+
+	ret = pmbus_read_byte_data(client, page, reg);
+	if (ret < 0)
+		return ret;
+
+	on_off_config = pmbus_read_byte_data(client, page,
+					     PMBUS_ON_OFF_CONFIG);
+	if (on_off_config < 0)
+		return on_off_config;
+
+	enabled = !!(on_off_config & PB_ON_OFF_CONFIG_POLARITY_HIGH);
+
+	enabled ^= data->en_pin_lvl;
+	if (enabled)
+		ret &= ~PB_OPERATION_CONTROL_ON;
+	else
+		ret |= PB_OPERATION_CONTROL_ON;
+
+	return ret;
+}
+
+/*
+ * Map PB_OPERATION_CONTROL_ON to PB_ON_OFF_CONFIG_POLARITY_HIGH.
+ */
+static int tda38640_write_byte_data(struct i2c_client *client, int page,
+				    int reg, u8 byte)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct tda38640_data *data = to_tda38640_data(info);
+	int enable, ret;
+
+	if (reg != PMBUS_OPERATION)
+		return -ENODATA;
+
+	enable = !!(byte & PB_OPERATION_CONTROL_ON);
+
+	byte &= ~PB_OPERATION_CONTROL_ON;
+	ret = pmbus_write_byte_data(client, page, reg, byte);
+	if (ret < 0)
+		return ret;
+
+	enable ^= data->en_pin_lvl;
+
+	return pmbus_update_byte_data(client, page, PMBUS_ON_OFF_CONFIG,
+				      PB_ON_OFF_CONFIG_POLARITY_HIGH,
+				      enable ? 0 : PB_ON_OFF_CONFIG_POLARITY_HIGH);
+}
+
+static int svid_mode(struct i2c_client *client, struct tda38640_data *data)
+{
+	/* PMBUS_MFR_READ(0xD0) + MTP Address offset */
+	u8 write_buf[] = {0xd0, 0x44, 0x00};
+	u8 read_buf[2];
+	int ret, svid;
+	bool off, reg_en_pin_pol;
+
+	struct i2c_msg msgs[2] = {
+		{
+			.addr = client->addr,
+			.flags = 0,
+			.buf = write_buf,
+			.len = sizeof(write_buf),
+		},
+		{
+			.addr = client->addr,
+			.flags = I2C_M_RD,
+			.buf = read_buf,
+			.len = sizeof(read_buf),
+		}
+	};
+
+	ret = i2c_transfer(client->adapter, msgs, 2);
+	if (ret < 0) {
+		dev_err(&client->dev, "i2c_transfer failed. %d", ret);
+		return ret;
+	}
+
+	/*
+	 * 0x44[15] determines PMBus Operating Mode
+	 * If bit is set then it is SVID mode.
+	 */
+	svid = !!(read_buf[1] & BIT(7));
+
+	/*
+	 * Determine EN pin level for use in SVID mode.
+	 * This is done with help of STATUS_BYTE bit 6(OFF) & ON_OFF_CONFIG bit 2(EN pin polarity).
+	 */
+	if (svid) {
+		ret = i2c_smbus_read_byte_data(client, PMBUS_STATUS_BYTE);
+		if (ret < 0)
+			return ret;
+		off = !!(ret & PB_STATUS_OFF);
+
+		ret = i2c_smbus_read_byte_data(client, PMBUS_ON_OFF_CONFIG);
+		if (ret < 0)
+			return ret;
+		reg_en_pin_pol = !!(ret & PB_ON_OFF_CONFIG_POLARITY_HIGH);
+		data->en_pin_lvl = off ^ reg_en_pin_pol;
+	}
+
+	return svid;
+}
+
 static struct pmbus_driver_info tda38640_info = {
 	.pages = 1,
 	.format[PSC_VOLTAGE_IN] = linear,
@@ -26,7 +147,6 @@ static struct pmbus_driver_info tda38640_info = {
 	.format[PSC_CURRENT_IN] = linear,
 	.format[PSC_POWER] = linear,
 	.format[PSC_TEMPERATURE] = linear,
-
 	.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT
 	    | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP
 	    | PMBUS_HAVE_IIN
@@ -41,7 +161,34 @@ static struct pmbus_driver_info tda38640_info = {
 
 static int tda38640_probe(struct i2c_client *client)
 {
-	return pmbus_do_probe(client, &tda38640_info);
+	struct tda38640_data *data;
+	int svid;
+
+	data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+	memcpy(&data->info, &tda38640_info, sizeof(tda38640_info));
+
+	svid = svid_mode(client, data);
+	if (svid < 0) {
+		dev_err_probe(&client->dev, svid, "Could not determine operating mode.");
+		return svid;
+	}
+
+	if (IS_ENABLED(CONFIG_SENSORS_TDA38640_REGULATOR) || svid) {
+		/*
+		 * Apply ON_OFF_CONFIG workaround as enabling the regulator using the
+		 * OPERATION register doesn't work in SVID mode.
+		 *
+		 * One should configure PMBUS_ON_OFF_CONFIG here, but
+		 * PB_ON_OFF_CONFIG_POWERUP_CONTROL and PB_ON_OFF_CONFIG_EN_PIN_REQ
+		 * are ignored by the device.
+		 * Only PB_ON_OFF_CONFIG_POLARITY_HIGH has an effect.
+		 */
+		data->info.read_byte_data = tda38640_read_byte_data;
+		data->info.write_byte_data = tda38640_write_byte_data;
+	}
+	return pmbus_do_probe(client, &data->info);
 }
 
 static const struct i2c_device_id tda38640_id[] = {
Signature · 1 line
2.41.0
maintainer
#2 lore raw

Re: [PATCH v2 2/2] hwmon: (pmbus/tda38640) Add workaround for bug in SVID mode

Quoted 179 lines · Naresh Solanki

From: Patrick Rudolph <[email protected]>

Introduce a workaround to handle the issue where the regulator cannot be enabled using BIT7 of the OPERATION(01h) register when in SVID mode.

It works when in PMBUS mode. In SVID mode the regulator only cares about the ENABLE pin.

Determine if chip is in SVID mode by checking BIT15 of MTP memory offset 0x44 as described in the datasheet.

If chip is in SVID mode then apply the workaround by
1. Determine EN pin level
2. Maps BIT7 of OPERATION(01h) to EN_PIN_POLARITY(BIT1) of PB_ON_OFF_CONFIG.

Tested working of TDA38640 in both SVID & PMBus mode.

----
Changes in V2:
- Remove dependency on DT propery,
- Runtime determine SVID mode & ENABLE pin level,
- Update commit message.

---
  drivers/hwmon/pmbus/tda38640.c | 151 ++++++++++++++++++++++++++++++++-
  1 file changed, 149 insertions(+), 2 deletions(-)
drivers/hwmon/pmbus/tda38640.c +126 -2
index 450b0273fb59..daaf77f8bf82 100644
@@ -18,6 +18,127 @@ static const struct regulator_desc __maybe_unused tda38640_reg_desc[] = {
  	PMBUS_REGULATOR("vout", 0),
  };
 
+struct tda38640_data {
+	struct pmbus_driver_info info;
+	u32 en_pin_lvl;
+};
+
+#define to_tda38640_data(x)  container_of(x, struct tda38640_data, info)
+
+/*
+ * Map PB_ON_OFF_CONFIG_POLARITY_HIGH to PB_OPERATION_CONTROL_ON.
+ */
+static int tda38640_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct tda38640_data *data = to_tda38640_data(info);
+	int ret, on_off_config, enabled;
+
+	if (reg != PMBUS_OPERATION)
+		return -ENODATA;
+
+	ret = pmbus_read_byte_data(client, page, reg);
+	if (ret < 0)
+		return ret;
+
+	on_off_config = pmbus_read_byte_data(client, page,
+					     PMBUS_ON_OFF_CONFIG);
+	if (on_off_config < 0)
+		return on_off_config;
+
+	enabled = !!(on_off_config & PB_ON_OFF_CONFIG_POLARITY_HIGH);
+
+	enabled ^= data->en_pin_lvl;
+	if (enabled)
+		ret &= ~PB_OPERATION_CONTROL_ON;
+	else
+		ret |= PB_OPERATION_CONTROL_ON;
+
+	return ret;
+}
+
+/*
+ * Map PB_OPERATION_CONTROL_ON to PB_ON_OFF_CONFIG_POLARITY_HIGH.
+ */
+static int tda38640_write_byte_data(struct i2c_client *client, int page,
+				    int reg, u8 byte)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	struct tda38640_data *data = to_tda38640_data(info);
+	int enable, ret;
+
+	if (reg != PMBUS_OPERATION)
+		return -ENODATA;
+
+	enable = !!(byte & PB_OPERATION_CONTROL_ON);
+
+	byte &= ~PB_OPERATION_CONTROL_ON;
+	ret = pmbus_write_byte_data(client, page, reg, byte);
+	if (ret < 0)
+		return ret;
+
+	enable ^= data->en_pin_lvl;
+
+	return pmbus_update_byte_data(client, page, PMBUS_ON_OFF_CONFIG,
+				      PB_ON_OFF_CONFIG_POLARITY_HIGH,
+				      enable ? 0 : PB_ON_OFF_CONFIG_POLARITY_HIGH);
+}
+
+static int svid_mode(struct i2c_client *client, struct tda38640_data *data)
+{
+	/* PMBUS_MFR_READ(0xD0) + MTP Address offset */
+	u8 write_buf[] = {0xd0, 0x44, 0x00};
+	u8 read_buf[2];
+	int ret, svid;
+	bool off, reg_en_pin_pol;
+
+	struct i2c_msg msgs[2] = {
+		{
+			.addr = client->addr,
+			.flags = 0,
+			.buf = write_buf,
+			.len = sizeof(write_buf),
+		},
+		{
+			.addr = client->addr,
+			.flags = I2C_M_RD,
+			.buf = read_buf,
+			.len = sizeof(read_buf),
+		}
+	};
+
+	ret = i2c_transfer(client->adapter, msgs, 2);
+	if (ret < 0) {
+		dev_err(&client->dev, "i2c_transfer failed. %d", ret);
+		return ret;
+	}
+
+	/*
+	 * 0x44[15] determines PMBus Operating Mode
+	 * If bit is set then it is SVID mode.
+	 */
+	svid = !!(read_buf[1] & BIT(7));
+
+	/*
+	 * Determine EN pin level for use in SVID mode.
+	 * This is done with help of STATUS_BYTE bit 6(OFF) & ON_OFF_CONFIG bit 2(EN pin polarity).
+	 */
+	if (svid) {
+		ret = i2c_smbus_read_byte_data(client, PMBUS_STATUS_BYTE);
+		if (ret < 0)
+			return ret;
+		off = !!(ret & PB_STATUS_OFF);
+
+		ret = i2c_smbus_read_byte_data(client, PMBUS_ON_OFF_CONFIG);
+		if (ret < 0)
+			return ret;
+		reg_en_pin_pol = !!(ret & PB_ON_OFF_CONFIG_POLARITY_HIGH);
+		data->en_pin_lvl = off ^ reg_en_pin_pol;
+	}
+
+	return svid;
+}
+
  static struct pmbus_driver_info tda38640_info = {
  	.pages = 1,
  	.format[PSC_VOLTAGE_IN] = linear,
@@ -26,7 +147,6 @@ static struct pmbus_driver_info tda38640_info = {
  	.format[PSC_CURRENT_IN] = linear,
  	.format[PSC_POWER] = linear,
  	.format[PSC_TEMPERATURE] = linear,
-
  	.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT
  	    | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP
  	    | PMBUS_HAVE_IIN
@@ -41,7 +161,34 @@ static struct pmbus_driver_info tda38640_info = {
 
  static int tda38640_probe(struct i2c_client *client)
  {
-	return pmbus_do_probe(client, &tda38640_info);
+	struct tda38640_data *data;
+	int svid;
+
+	data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)

drivers/hwmon/pmbus/tda38640.c static struct pmbus_driver_info tda38640_info = { · line 178

Quoted 10 lines
drivers/hwmon/pmbus/tda38640.c +10 -0
+		return -ENOMEM;
+	memcpy(&data->info, &tda38640_info, sizeof(tda38640_info));
+
+	svid = svid_mode(client, data);
+	if (svid < 0) {
+		dev_err_probe(&client->dev, svid, "Could not determine operating mode.");
+		return svid;
+	}
+
+	if (IS_ENABLED(CONFIG_SENSORS_TDA38640_REGULATOR) || svid) {

If you hide this behind IS_ENABLED(CONFIG_SENSORS_TDA38640_REGULATOR), reading svid outside the if() statement has no value.

drivers/hwmon/pmbus/tda38640.c static struct pmbus_driver_info tda38640_info = { · line 186

Quoted 8 lines
drivers/hwmon/pmbus/tda38640.c +8 -0
+		/*
+		 * Apply ON_OFF_CONFIG workaround as enabling the regulator using the
+		 * OPERATION register doesn't work in SVID mode.
+		 *
+		 * One should configure PMBUS_ON_OFF_CONFIG here, but
+		 * PB_ON_OFF_CONFIG_POWERUP_CONTROL and PB_ON_OFF_CONFIG_EN_PIN_REQ
+		 * are ignored by the device.
+		 * Only PB_ON_OFF_CONFIG_POLARITY_HIGH has an effect.

Hmm, maybe I start to understand. This is really weird, since it changes the polarity of the EN input pin, effectively reverting its value. In other words, what really happens is that it is not possible to disable the chip with PMBUS_ON_OFF_CONFIG in SVID mode, and that reverting the EN pin polarity effectively simulates turning the chip on or off by software. Maybe software enable is disabled on purpose in VID mode. Is that really a bug or is it a feature, and is it really a good idea to override it ?

AN_2203_PL12_2204_184108 might really help here.

Guenter

Quoted 8 lines
drivers/hwmon/pmbus/tda38640.c +5 -0
+		 */
+		data->info.read_byte_data = tda38640_read_byte_data;
+		data->info.write_byte_data = tda38640_write_byte_data;
+	}
+	return pmbus_do_probe(client, &data->info);
  }
 
  static const struct i2c_device_id tda38640_id[] = {
#3 lore raw

Re: [PATCH v2 2/2] hwmon: (pmbus/tda38640) Add workaround for bug in SVID mode

Hi Guenter,

Quoted 186 lines · Guenter Roeck
Quoted 184 lines · Naresh Solanki

From: Patrick Rudolph <[email protected]>

Introduce a workaround to handle the issue where the regulator cannot be enabled using BIT7 of the OPERATION(01h) register when in SVID mode.

It works when in PMBUS mode. In SVID mode the regulator only cares about the ENABLE pin.

Determine if chip is in SVID mode by checking BIT15 of MTP memory offset 0x44 as described in the datasheet.

If chip is in SVID mode then apply the workaround by
1. Determine EN pin level
2. Maps BIT7 of OPERATION(01h) to EN_PIN_POLARITY(BIT1) of PB_ON_OFF_CONFIG.

Tested working of TDA38640 in both SVID & PMBus mode.

----
Changes in V2:
- Remove dependency on DT propery,
- Runtime determine SVID mode & ENABLE pin level,
- Update commit message.

---
  drivers/hwmon/pmbus/tda38640.c | 151 ++++++++++++++++++++++++++++++++-
  1 file changed, 149 insertions(+), 2 deletions(-)
drivers/hwmon/pmbus/tda38640.c +131 -2
index 450b0273fb59..daaf77f8bf82 100644
@@ -18,6 +18,127 @@ static const struct regulator_desc __maybe_unused tda38640_reg_desc[] = {
      PMBUS_REGULATOR("vout", 0),
  };
 
+struct tda38640_data {
+     struct pmbus_driver_info info;
+     u32 en_pin_lvl;
+};
+
+#define to_tda38640_data(x)  container_of(x, struct tda38640_data, info)
+
+/*
+ * Map PB_ON_OFF_CONFIG_POLARITY_HIGH to PB_OPERATION_CONTROL_ON.
+ */
+static int tda38640_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+     const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+     struct tda38640_data *data = to_tda38640_data(info);
+     int ret, on_off_config, enabled;
+
+     if (reg != PMBUS_OPERATION)
+             return -ENODATA;
+
+     ret = pmbus_read_byte_data(client, page, reg);
+     if (ret < 0)
+             return ret;
+
+     on_off_config = pmbus_read_byte_data(client, page,
+                                          PMBUS_ON_OFF_CONFIG);
+     if (on_off_config < 0)
+             return on_off_config;
+
+     enabled = !!(on_off_config & PB_ON_OFF_CONFIG_POLARITY_HIGH);
+
+     enabled ^= data->en_pin_lvl;
+     if (enabled)
+             ret &= ~PB_OPERATION_CONTROL_ON;
+     else
+             ret |= PB_OPERATION_CONTROL_ON;
+
+     return ret;
+}
+
+/*
+ * Map PB_OPERATION_CONTROL_ON to PB_ON_OFF_CONFIG_POLARITY_HIGH.
+ */
+static int tda38640_write_byte_data(struct i2c_client *client, int page,
+                                 int reg, u8 byte)
+{
+     const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+     struct tda38640_data *data = to_tda38640_data(info);
+     int enable, ret;
+
+     if (reg != PMBUS_OPERATION)
+             return -ENODATA;
+
+     enable = !!(byte & PB_OPERATION_CONTROL_ON);
+
+     byte &= ~PB_OPERATION_CONTROL_ON;
+     ret = pmbus_write_byte_data(client, page, reg, byte);
+     if (ret < 0)
+             return ret;
+
+     enable ^= data->en_pin_lvl;
+
+     return pmbus_update_byte_data(client, page, PMBUS_ON_OFF_CONFIG,
+                                   PB_ON_OFF_CONFIG_POLARITY_HIGH,
+                                   enable ? 0 : PB_ON_OFF_CONFIG_POLARITY_HIGH);
+}
+
+static int svid_mode(struct i2c_client *client, struct tda38640_data *data)
+{
+     /* PMBUS_MFR_READ(0xD0) + MTP Address offset */
+     u8 write_buf[] = {0xd0, 0x44, 0x00};
+     u8 read_buf[2];
+     int ret, svid;
+     bool off, reg_en_pin_pol;
+
+     struct i2c_msg msgs[2] = {
+             {
+                     .addr = client->addr,
+                     .flags = 0,
+                     .buf = write_buf,
+                     .len = sizeof(write_buf),
+             },
+             {
+                     .addr = client->addr,
+                     .flags = I2C_M_RD,
+                     .buf = read_buf,
+                     .len = sizeof(read_buf),
+             }
+     };
+
+     ret = i2c_transfer(client->adapter, msgs, 2);
+     if (ret < 0) {
+             dev_err(&client->dev, "i2c_transfer failed. %d", ret);
+             return ret;
+     }
+
+     /*
+      * 0x44[15] determines PMBus Operating Mode
+      * If bit is set then it is SVID mode.
+      */
+     svid = !!(read_buf[1] & BIT(7));
+
+     /*
+      * Determine EN pin level for use in SVID mode.
+      * This is done with help of STATUS_BYTE bit 6(OFF) & ON_OFF_CONFIG bit 2(EN pin polarity).
+      */
+     if (svid) {
+             ret = i2c_smbus_read_byte_data(client, PMBUS_STATUS_BYTE);
+             if (ret < 0)
+                     return ret;
+             off = !!(ret & PB_STATUS_OFF);
+
+             ret = i2c_smbus_read_byte_data(client, PMBUS_ON_OFF_CONFIG);
+             if (ret < 0)
+                     return ret;
+             reg_en_pin_pol = !!(ret & PB_ON_OFF_CONFIG_POLARITY_HIGH);
+             data->en_pin_lvl = off ^ reg_en_pin_pol;
+     }
+
+     return svid;
+}
+
  static struct pmbus_driver_info tda38640_info = {
      .pages = 1,
      .format[PSC_VOLTAGE_IN] = linear,
@@ -26,7 +147,6 @@ static struct pmbus_driver_info tda38640_info = {
      .format[PSC_CURRENT_IN] = linear,
      .format[PSC_POWER] = linear,
      .format[PSC_TEMPERATURE] = linear,
-
      .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT
          | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP
          | PMBUS_HAVE_IIN
@@ -41,7 +161,34 @@ static struct pmbus_driver_info tda38640_info = {
 
  static int tda38640_probe(struct i2c_client *client)
  {
-     return pmbus_do_probe(client, &tda38640_info);
+     struct tda38640_data *data;
+     int svid;
+
+     data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
+     if (!data)
+             return -ENOMEM;
+     memcpy(&data->info, &tda38640_info, sizeof(tda38640_info));
+
+     svid = svid_mode(client, data);
+     if (svid < 0) {
Quoted 8 lines

drivers/hwmon/pmbus/tda38640.c static struct pmbus_driver_info tda38640_info = { · line 178

Quoted 5 lines
drivers/hwmon/pmbus/tda38640.c +5 -0
+             dev_err_probe(&client->dev, svid, "Could not determine operating mode.");
+             return svid;
+     }
+
+     if (IS_ENABLED(CONFIG_SENSORS_TDA38640_REGULATOR) || svid) {

If you hide this behind IS_ENABLED(CONFIG_SENSORS_TDA38640_REGULATOR), reading svid outside the if() statement has no value.

svid mode check is needed only when regulator is enabled for on/off control later.
Will align the code such that if svid_mode check is done only when REGULATOR config is enabled
& if it is in svid mode then apply the WA.

Quoted 10 lines

drivers/hwmon/pmbus/tda38640.c static struct pmbus_driver_info tda38640_info = { · line 186

Quoted 9 lines
drivers/hwmon/pmbus/tda38640.c +8 -0
+             /*
+              * Apply ON_OFF_CONFIG workaround as enabling the regulator using the
+              * OPERATION register doesn't work in SVID mode.
+              *
+              * One should configure PMBUS_ON_OFF_CONFIG here, but
+              * PB_ON_OFF_CONFIG_POWERUP_CONTROL and PB_ON_OFF_CONFIG_EN_PIN_REQ
+              * are ignored by the device.
+              * Only PB_ON_OFF_CONFIG_POLARITY_HIGH has an effect.
Quoted 8 lines

Hmm, maybe I start to understand. This is really weird, since it changes the polarity of the EN input pin, effectively reverting its value. In other words, what really happens is that it is not possible to disable the chip with PMBUS_ON_OFF_CONFIG in SVID mode, and that reverting the EN pin polarity effectively simulates turning the chip on or off by software. Maybe software enable is disabled on purpose in VID mode. Is that really a bug or is it a feature, and is it really a good idea to override it ?

By design, SVID mode only has HW control enabled.
This was with the assumption that PGOOD will be used for controlling Enable of another rail in Hardware.

Since my use case needs the complete PMBUS based control, EN pin polarity flipping can be used for controlling output.

Quoted 14 lines

AN_2203_PL12_2204_184108 might really help here.

Guenter

Quoted 8 lines
drivers/hwmon/pmbus/tda38640.c +5 -0
+              */
+             data->info.read_byte_data = tda38640_read_byte_data;
+             data->info.write_byte_data = tda38640_write_byte_data;
+     }
+     return pmbus_do_probe(client, &data->info);
  }
 
  static const struct i2c_device_id tda38640_id[] = {
maintainer
#4 lore raw

Re: [PATCH v2 2/2] hwmon: (pmbus/tda38640) Add workaround for bug in SVID mode

On 8/1/23 05:34, Naresh Solanki wrote:

[ ... ]

Quoted 28 lines
Quoted 4 lines
Quoted 1 line

+ if (IS_ENABLED(CONFIG_SENSORS_TDA38640_REGULATOR) || svid) {

If you hide this behind IS_ENABLED(CONFIG_SENSORS_TDA38640_REGULATOR), reading svid outside the if() statement has no value.

svid mode check is needed only when regulator is enabled for on/off control later.
Will align the code such that if svid_mode check is done only when REGULATOR config is enabled
& if it is in svid mode then apply the WA.

Quoted 10 lines

drivers/hwmon/pmbus/tda38640.c static struct pmbus_driver_info tda38640_info = { · line 186

Quoted 9 lines
drivers/hwmon/pmbus/tda38640.c +8 -0
+             /*
+              * Apply ON_OFF_CONFIG workaround as enabling the regulator using the
+              * OPERATION register doesn't work in SVID mode.
+              *
+              * One should configure PMBUS_ON_OFF_CONFIG here, but
+              * PB_ON_OFF_CONFIG_POWERUP_CONTROL and PB_ON_OFF_CONFIG_EN_PIN_REQ
+              * are ignored by the device.
+              * Only PB_ON_OFF_CONFIG_POLARITY_HIGH has an effect.
Quoted 8 lines

Hmm, maybe I start to understand. This is really weird, since it changes the polarity of the EN input pin, effectively reverting its value. In other words, what really happens is that it is not possible to disable the chip with PMBUS_ON_OFF_CONFIG in SVID mode, and that reverting the EN pin polarity effectively simulates turning the chip on or off by software. Maybe software enable is disabled on purpose in VID mode. Is that really a bug or is it a feature, and is it really a good idea to override it ?

Quoted 7 lines

By design, SVID mode only has HW control enabled.
This was with the assumption that PGOOD will be used for controlling Enable of another rail in Hardware.

Since my use case needs the complete PMBUS based control, EN pin polarity flipping can be used for controlling output.

So, effectively, this is not really a bug. It is working around chip functionality.

That means we can not just enable this unconditionally in SVID mode after all. Sorry, but it has to be configurable after all, with appropriate explanation.

Guenter

Quoted 14 lines
Quoted 14 lines

AN_2203_PL12_2204_184108 might really help here.

Guenter

Quoted 8 lines
drivers/hwmon/pmbus/tda38640.c +5 -0
+              */
+             data->info.read_byte_data = tda38640_read_byte_data;
+             data->info.write_byte_data = tda38640_write_byte_data;
+     }
+     return pmbus_do_probe(client, &data->info);
   }
 
   static const struct i2c_device_id tda38640_id[] = {
#5 lore raw

Re: [PATCH v2 2/2] hwmon: (pmbus/tda38640) Add workaround for bug in SVID mode

Hi Guenter,

Quoted 37 lines · Naresh Solanki

[ ... ]

Quoted 32 lines
Quoted 4 lines
Quoted 1 line

+ if (IS_ENABLED(CONFIG_SENSORS_TDA38640_REGULATOR) || svid) {

If you hide this behind IS_ENABLED(CONFIG_SENSORS_TDA38640_REGULATOR), reading svid outside the if() statement has no value.

svid mode check is needed only when regulator is enabled for on/off control later.
Will align the code such that if svid_mode check is done only when REGULATOR config is enabled
& if it is in svid mode then apply the WA.

Quoted 10 lines

drivers/hwmon/pmbus/tda38640.c static struct pmbus_driver_info tda38640_info = { · line 186

Quoted 9 lines
drivers/hwmon/pmbus/tda38640.c +8 -0
+             /*
+              * Apply ON_OFF_CONFIG workaround as enabling the regulator using the
+              * OPERATION register doesn't work in SVID mode.
+              *
+              * One should configure PMBUS_ON_OFF_CONFIG here, but
+              * PB_ON_OFF_CONFIG_POWERUP_CONTROL and PB_ON_OFF_CONFIG_EN_PIN_REQ
+              * are ignored by the device.
+              * Only PB_ON_OFF_CONFIG_POLARITY_HIGH has an effect.
Quoted 8 lines

Hmm, maybe I start to understand. This is really weird, since it changes the polarity of the EN input pin, effectively reverting its value. In other words, what really happens is that it is not possible to disable the chip with PMBUS_ON_OFF_CONFIG in SVID mode, and that reverting the EN pin polarity effectively simulates turning the chip on or off by software. Maybe software enable is disabled on purpose in VID mode. Is that really a bug or is it a feature, and is it really a good idea to override it ?

By design, SVID mode only has HW control enabled.
This was with the assumption that PGOOD will be used for controlling Enable of another rail in Hardware.

Quoted 8 lines
Quoted 3 lines

Since my use case needs the complete PMBUS based control, EN pin polarity flipping can be used for controlling output.

So, effectively, this is not really a bug. It is working around chip functionality.

That means we can not just enable this unconditionally in SVID mode after all. Sorry, but it has to be configurable after all, with appropriate explanation.

By 'configurable' you mean add a dt-property like 'en-svid-control' to have this enabled ?

Regards,
Naresh

Quoted 18 lines

Guenter

Quoted 14 lines
Quoted 14 lines

AN_2203_PL12_2204_184108 might really help here.

Guenter

Quoted 8 lines
drivers/hwmon/pmbus/tda38640.c +5 -0
+              */
+             data->info.read_byte_data = tda38640_read_byte_data;
+             data->info.write_byte_data = tda38640_write_byte_data;
+     }
+     return pmbus_do_probe(client, &data->info);
   }
 
   static const struct i2c_device_id tda38640_id[] = {
maintainer
#6 lore raw

Re: [PATCH v2 2/2] hwmon: (pmbus/tda38640) Add workaround for bug in SVID mode

Quoted 43 lines · Naresh Solanki

Hi Guenter,

Quoted 41 lines · Naresh Solanki

[ ... ]

Quoted 35 lines
Quoted 4 lines
Quoted 1 line

+ if (IS_ENABLED(CONFIG_SENSORS_TDA38640_REGULATOR) || svid) {

If you hide this behind IS_ENABLED(CONFIG_SENSORS_TDA38640_REGULATOR), reading svid outside the if() statement has no value.

svid mode check is needed only when regulator is enabled for on/off control later.
Will align the code such that if svid_mode check is done only when REGULATOR config is enabled
& if it is in svid mode then apply the WA.

Quoted 10 lines

drivers/hwmon/pmbus/tda38640.c static struct pmbus_driver_info tda38640_info = { · line 186

Quoted 9 lines
drivers/hwmon/pmbus/tda38640.c +8 -0
+             /*
+              * Apply ON_OFF_CONFIG workaround as enabling the regulator using the
+              * OPERATION register doesn't work in SVID mode.
+              *
+              * One should configure PMBUS_ON_OFF_CONFIG here, but
+              * PB_ON_OFF_CONFIG_POWERUP_CONTROL and PB_ON_OFF_CONFIG_EN_PIN_REQ
+              * are ignored by the device.
+              * Only PB_ON_OFF_CONFIG_POLARITY_HIGH has an effect.
Quoted 8 lines

Hmm, maybe I start to understand. This is really weird, since it changes the polarity of the EN input pin, effectively reverting its value. In other words, what really happens is that it is not possible to disable the chip with PMBUS_ON_OFF_CONFIG in SVID mode, and that reverting the EN pin polarity effectively simulates turning the chip on or off by software. Maybe software enable is disabled on purpose in VID mode. Is that really a bug or is it a feature, and is it really a good idea to override it ?

By design, SVID mode only has HW control enabled.
This was with the assumption that PGOOD will be used for controlling Enable of another rail in Hardware.

Since my use case needs the complete PMBUS based control, EN pin polarity flipping can be used for controlling output.

Quoted 7 lines
Quoted 4 lines

So, effectively, this is not really a bug. It is working around chip functionality.

That means we can not just enable this unconditionally in SVID mode after all. Sorry, but it has to be configurable after all, with appropriate explanation.

By 'configurable' you mean add a dt-property like 'en-svid-control' to have this enabled ?

Yes. After all, not everyone may want this, and it is quite obvious to me that it is not a bug but normal operation for the chip in SVID mode. Besides, it is difficult to determine how the chip performs when manipulating the EN input in SVID mode; I don't understand SVID well enough to be able to determine if doing that is even valid in that mode. So we definitely don't want to enable this for other users of the chip.

Sorry, my initial understanding was that this is a bug. I am now convinced that it isn't.

Guenter

Quoted 20 lines

Regards,
Naresh

Quoted 18 lines

Guenter

Quoted 14 lines
Quoted 14 lines

AN_2203_PL12_2204_184108 might really help here.

Guenter

Quoted 8 lines
drivers/hwmon/pmbus/tda38640.c +5 -0
+              */
+             data->info.read_byte_data = tda38640_read_byte_data;
+             data->info.write_byte_data = tda38640_write_byte_data;
+     }
+     return pmbus_do_probe(client, &data->info);
    }
 
    static const struct i2c_device_id tda38640_id[] = {