Skip to contentSkip to conversation

board: ti: Add support for BeaglePlay

PATCH Superseded Nishanth Menon 1 participant 6 messages Jul 27, 2023 Arm (32-bit)

v2 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v2 cover board: ti: Add support for BeaglePlay

Add support for BeaglePlay - rev 2

Boot log: https://gist.github.com/nmenon/bee1ab7cbfd188574cfb843e336fbe40

Full series(including dependencies) can be found at:
https://github.com/nmenon/fix-k3-dt-u-boot/commits/beagleplay-v2.2

Depends on:
a) https://lore.kernel.org/all/[email protected]/ (with it's dependencies)
b) https://lore.kernel.org/all/[email protected]/ (for the documentation patch)
c) The last patch in the series (labelled TMP), depends on the RFC and debated upon patch (to introduce config fragments)
https://lore.kernel.org/all/[email protected]/

Caveats:
* I have kept networking out of picture for now as it is still evolving.

Changes since V1:
* I moved the documentation patches over to the documentation improvement series
* Fixes the documentation comments provided and reworked wording a bit
* Dropped the controversial voltage and 32k settings patch for now while we figure out how to get it in properly
* Added config fragments as an add-on patch - I'd rather see us migrate there at some near term point.

V1: https://lore.kernel.org/all/[email protected]/

Nishanth Menon (4):
arm: dts: k3-am625-sk-binman: Add labels for unsigned binary
configs: Add am62x_beagleplay_* defconfigs
doc: board: ti: Add BeaglePlay documentation
TMP: board: ti: am62x: Switch over to config fragments

Robert Nelson (1):
arm: dts: Add k3-am625-beagleplay

 arch/arm/dts/Makefile                         |    4 +-
 .../dts/k3-am625-beagleplay-ddr4-1600MTs.dtsi | 2195 +++++++++++++++++
 arch/arm/dts/k3-am625-beagleplay-u-boot.dtsi  |  172 ++
 arch/arm/dts/k3-am625-beagleplay.dts          |  758 ++++++
 arch/arm/dts/k3-am625-r5-beagleplay.dts       |   87 +
 arch/arm/dts/k3-am625-sk-binman.dtsi          |    4 +-
 board/ti/am62x/beagleplay_a53.config          |   20 +
 board/ti/am62x/beagleplay_r5.config           |   11 +
 doc/board/ti/am62x_beagleplay.rst             |  120 +
 doc/board/ti/k3.rst                           |    1 +
 10 files changed, 3369 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm/dts/k3-am625-beagleplay-ddr4-1600MTs.dtsi
 create mode 100644 arch/arm/dts/k3-am625-beagleplay-u-boot.dtsi
 create mode 100644 arch/arm/dts/k3-am625-beagleplay.dts
 create mode 100644 arch/arm/dts/k3-am625-r5-beagleplay.dts
 create mode 100644 board/ti/am62x/beagleplay_a53.config
 create mode 100644 board/ti/am62x/beagleplay_r5.config
 create mode 100644 doc/board/ti/am62x_beagleplay.rst
Signature · 1 line
2.40.0
#1 lore raw

PATCH v2 1/5 arm: dts: k3-am625-sk-binman: Add labels for unsigned binary

Add labels for unsigned binary to permit over-ride.

---

I think we might also want to review Neha's approach in RFC stage if this is not acceptable, but I suspect other boards will have similar challenges:
https://lore.kernel.org/all/[email protected]/

Changes since V1: None
V1: https://lore.kernel.org/all/[email protected]/

 arch/arm/dts/k3-am625-sk-binman.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/dts/k3-am625-sk-binman.dtsi +2 -2
index a35d6418c25f..41277bf4bfdb 100644
@@ -389,7 +389,7 @@
 					type = "flat_dt";
 					arch = "arm";
 					compression = "none";
-					blob {
+					spl_am625_sk_dtb_unsigned: blob {
 						filename = SPL_AM625_SK_DTB;
 					};
 				};
@@ -438,7 +438,7 @@
 					type = "flat_dt";
 					arch = "arm";
 					compression = "none";
-					blob {
+					am625_sk_dtb_unsigned: blob {
 						filename = AM625_SK_DTB;
 					};
 					hash {
Signature · 1 line
2.40.0
#2 lore raw

PATCH v2 2/5 arm: dts: Add k3-am625-beagleplay

In reply to Nishanth Menon

From: Robert Nelson <[email protected]>

BeagleBoard.org BeaglePlay is an easy to use, affordable open source hardware single board computer based on the Texas Instruments AM625 SoC that allows you to create connected devices that work even at long distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L. Expansion is provided over open standards based mikroBUS, Grove and QWIIC headers among other interfaces.

This board family can be identified by the 24c32 eeprom:

[aa 55 33 ee 01 37 00 10  2e 00 42 45 41 47 4c 45  |.U3..7....BEAGLE|]
[50 4c 41 59 2d 41 30 2d  00 00 30 32 30 30 37 38  |PLAY-A0-..020078|]

https://beagleplay.org/
https://git.beagleboard.org/beagleplay/beagleplay

baseline of base device tree is v6.5-rc1.

---
Changes since V1:
- None

V1: https://lore.kernel.org/all/[email protected]/

 arch/arm/dts/Makefile                         |    4 +-
 .../dts/k3-am625-beagleplay-ddr4-1600MTs.dtsi | 2195 +++++++++++++++++
 arch/arm/dts/k3-am625-beagleplay-u-boot.dtsi  |  172 ++
 arch/arm/dts/k3-am625-beagleplay.dts          |  758 ++++++
 arch/arm/dts/k3-am625-r5-beagleplay.dts       |   87 +
 5 files changed, 3215 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/k3-am625-beagleplay-ddr4-1600MTs.dtsi
 create mode 100644 arch/arm/dts/k3-am625-beagleplay-u-boot.dtsi
 create mode 100644 arch/arm/dts/k3-am625-beagleplay.dts
 create mode 100644 arch/arm/dts/k3-am625-r5-beagleplay.dts
arch/arm/dts/Makefile +3 -1
index b7780de776b6..1c83a2a576c3 100644
@@ -1304,7 +1304,9 @@ dtb-$(CONFIG_SOC_K3_AM642) += k3-am642-evm.dtb \
 			      k3-am642-r5-sk.dtb
 
 dtb-$(CONFIG_SOC_K3_AM625) += k3-am625-sk.dtb \
-			      k3-am625-r5-sk.dtb
+			      k3-am625-r5-sk.dtb \
+			      k3-am625-beagleplay.dtb \
+			      k3-am625-r5-beagleplay.dtb
 
 dtb-$(CONFIG_SOC_K3_AM62A7) += k3-am62a7-sk.dtb \
 			      k3-am62a7-r5-sk.dtb
arch/arm/dts/k3-am625-beagleplay-ddr4-1600MTs.dtsi new file +2195 -0

2,195 lines not on this page · raw message

arch/arm/dts/k3-am625-beagleplay-u-boot.dtsi new file +172 -0

172 lines not on this page · raw message

arch/arm/dts/k3-am625-beagleplay.dts new file +758 -0

623 lines not on this page · raw message

arch/arm/dts/k3-am625-r5-beagleplay.dts new file +87 -0

87 lines not on this page · raw message

The rest of this diff is not shown. View the raw message.

Signature · 1 line
2.40.0

Part of the diff is not shown here. View the raw message.

#3 lore raw

PATCH v2 3/5 configs: Add am62x_beagleplay_* defconfigs

In reply to Nishanth Menon

Add defconfigs for am625 based beagleplay

---
Changes since V1:
- None

V1: https://lore.kernel.org/all/[email protected]/

 configs/am62x_beagleplay_a53_defconfig |  90 ++++++++++++++++++++
 configs/am62x_beagleplay_r5_defconfig  | 110 +++++++++++++++++++++++++
 2 files changed, 200 insertions(+)
 create mode 100644 configs/am62x_beagleplay_a53_defconfig
 create mode 100644 configs/am62x_beagleplay_r5_defconfig
configs/am62x_beagleplay_a53_defconfig new file +90 -0
new file mode 100644
index 000000000000..e45cb2782579
@@ -0,0 +1,90 @@
+CONFIG_ARM=y
+CONFIG_ARCH_K3=y
+CONFIG_TI_SECURE_DEVICE=y
+CONFIG_SYS_MALLOC_F_LEN=0x8000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_SOC_K3_AM625=y
+CONFIG_K3_ATF_LOAD_ADDR=0x9e780000
+CONFIG_TARGET_AM625_A53_EVM=y
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80b80000
+CONFIG_SPL_DM_SPI=y
+CONFIG_DEFAULT_DEVICE_TREE="k3-am625-beagleplay"
+CONFIG_SPL_TEXT_BASE=0x80080000
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_DM_RESET=y
+CONFIG_SPL_MMC=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x82000000
+CONFIG_SPL_SIZE_LIMIT=0x40000
+CONFIG_SPL_SIZE_LIMIT_PROVIDE_STACK=0x800
+CONFIG_SPL_FS_FAT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+CONFIG_SPL_SPI=y
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
+CONFIG_AUTOBOOT_DELAY_STR="d"
+CONFIG_AUTOBOOT_STOP_STR=" "
+CONFIG_BOOTCOMMAND="run findfdt; run envboot; run distro_bootcmd"
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x80c80000
+CONFIG_SPL_BSS_MAX_SIZE=0x80000
+CONFIG_SPL_SYS_REPORT_STACK_F_USAGE=y
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SPL_STACK_R=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400
+CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot.img"
+CONFIG_SPL_DM_MAILBOX=y
+CONFIG_SPL_POWER_DOMAIN=y
+CONFIG_SPL_YMODEM_SUPPORT=y
+CONFIG_SYS_BOOTM_LEN=0x800000
+CONFIG_CMD_MMC=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_MULTI_DTB_FIT=y
+CONFIG_SPL_MULTI_DTB_FIT=y
+CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_TI_SCI=y
+CONFIG_DMA_CHANNELS=y
+CONFIG_TI_K3_NAVSS_UDMA=y
+CONFIG_TI_SCI_PROTOCOL=y
+CONFIG_DM_MAILBOX=y
+CONFIG_K3_SEC_PROXY=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ADMA=y
+CONFIG_SPL_MMC_SDHCI_ADMA=y
+CONFIG_MMC_SDHCI_AM654=y
+CONFIG_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_PINCTRL_SINGLE=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_TI_SCI_POWER_DOMAIN=y
+CONFIG_K3_SYSTEM_CONTROLLER=y
+CONFIG_REMOTEPROC_TI_K3_ARM64=y
+CONFIG_RESET_TI_SCI=y
+CONFIG_DM_SERIAL=y
+CONFIG_SOC_DEVICE=y
+CONFIG_SOC_DEVICE_TI_K3=y
+CONFIG_SOC_TI=y
+CONFIG_SYSRESET=y
+CONFIG_SPL_SYSRESET=y
+CONFIG_SYSRESET_TI_SCI=y
+CONFIG_EXT4_WRITE=y
+CONFIG_FS_FAT_MAX_CLUSTSIZE=16384
+CONFIG_LZO=y
configs/am62x_beagleplay_r5_defconfig new file +110 -0

110 lines not on this page · raw message

Signature · 1 line
2.40.0
#4 lore raw

PATCH v2 4/5 doc: board: ti: Add BeaglePlay documentation

In reply to Nishanth Menon

Add base documentation for BeaglePlay

---
Changes Since V1:
- Dependency added on top of doc cleanup
https://lore.kernel.org/all/[email protected]/
- Mostly rewrite.. hopefully for the better

V1: https://lore.kernel.org/all/[email protected]/

 doc/board/ti/am62x_beagleplay.rst | 120 ++++++++++++++++++++++++++++++
 doc/board/ti/k3.rst               |   1 +
 2 files changed, 121 insertions(+)
 create mode 100644 doc/board/ti/am62x_beagleplay.rst
doc/board/ti/am62x_beagleplay.rst new file +120 -0
new file mode 100644
index 000000000000..b97d8cead7fb
@@ -0,0 +1,120 @@
+.. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+.. sectionauthor:: Nishanth Menon <[email protected]>
+
+Beagleboard.org Beagleplay
+==========================
+
+Introduction:
+-------------
+
+BeagleBoard.org BeaglePlay is an easy to use, affordable open source
+hardware single board computer based on the Texas Instruments AM625
+SoC that allows you to create connected devices that work even at long
+distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
+Expansion is provided over open standards based mikroBUS, Grove and
+QWIIC headers among other interfaces.
+
+Further information can be found at:
+https://beagleplay.org/
+https://git.beagleboard.org/beagleplay/beagleplay
+
+Boot Flow:
+----------
+Below is the pictorial representation of boot flow:
+
+.. image:: img/boot_diagram_k3_current.svg
+
+- On this platform, 'TI Foundational Security' (TIFS) functions as the
+  security enclave master while 'Device Manager' (DM), also known as the
+  'TISCI server' in "TI terminology", offers all the essential services.
+  The A53/M4F (Aux core) sends requests to TIFS/DM to accomplish these
+  services, as illustrated in the diagram above.
+
+Sources:
+--------
+.. include::  k3.rst
+    :start-after: .. k3_rst_include_start_boot_sources
+    :end-before: .. k3_rst_include_end_boot_sources
+
+Build procedure:
+----------------
+0. Setup the environment variables:
+
+.. include::  k3.rst
+    :start-after: .. k3_rst_include_start_common_env_vars_desc
+    :end-before: .. k3_rst_include_end_common_env_vars_desc
+
+.. include::  k3.rst
+    :start-after: .. k3_rst_include_start_board_env_vars_desc
+    :end-before: .. k3_rst_include_end_board_env_vars_desc
+
+Set the variables corresponding to this platform:
+
+.. include::  k3.rst
+    :start-after: .. k3_rst_include_start_common_env_vars_defn
+    :end-before: .. k3_rst_include_end_common_env_vars_defn
+.. code-block:: bash
+
+ $ export UBOOT_CFG_CORTEXR=am62x_beagleplay_r5_defconfig
+ $ export UBOOT_CFG_CORTEXA=am62x_beagleplay_a53_defconfig
+ $ export TFA_BOARD=lite
+ $ # we dont use any extra TFA parameters
+ $ unset TFA_EXTRA_ARGS
+ $ export OPTEE_PLATFORM=k3-am62x
+ $ export OPTEE_EXTRA_ARGS="CFG_WITH_SOFTWARE_PRNG=y"
+
+.. include::  am62x_sk.rst
+    :start-after: .. am62x_evm_rst_include_start_build_steps
+    :end-before: .. am62x_evm_rst_include_end_build_steps
+
+Target Images
+--------------
+Copy the below images to an SD card and boot:
+
+* tiboot3-am62x-gp-evm.bin from R5 build as tiboot3.bin
+* tispl.bin_unsigned from Cortex-A build as tispl.bin
+* u-boot.img_unsigned from Cortex-A build as uboot.img
+
+Image formats:
+--------------
+
+- tiboot3.bin
+
+.. image:: img/multi_cert_tiboot3.bin.svg
+
+- tispl.bin
+
+.. image:: img/dm_tispl.bin.svg
+
+A53 SPL DDR Memory Layout
+-------------------------
+
+.. include::  am62x_sk.rst
+    :start-after: .. am62x_evm_rst_include_start_ddr_mem_layout
+    :end-before: .. am62x_evm_rst_include_end_ddr_mem_layout
+
+Switch Setting for Boot Mode
+----------------------------
+
+The boot time option is configured via "USR" button on the board.
+See https://git.beagleboard.org/beagleplay/beagleplay/-/blob/main/BeaglePlay_sch.pdf
+for details.
+
+.. list-table:: Boot Modes
+   :widths: 16 16 16
+   :header-rows: 1
+
+   * - USR Switch Position
+     - Primary Boot
+     - Secondary Boot
+
+   * - Not Pressed
+     - eMMC
+     - UART
+
+   * - Pressed
+     - SD/MMC File System (FS) mode
+     - USB Device Firmware Upgrade (DFU) mode
+
+To switch to SD card boot mode, hold the USR button while powering on
+with Type-C power supply, then release when power LED lights up.
doc/board/ti/k3.rst +1 -0
index 9d40675b6007..2876ec842a18 100644
@@ -30,6 +30,7 @@ K3 Based SoCs
 .. toctree::
    :maxdepth: 1
 
+   am62x_beagleplay
    am62x_sk
    am65x_evm
    j7200_evm
Signature · 1 line
2.40.0
#5 lore raw

PATCH v2 5/5 TMP: board: ti: am62x: Switch over to config fragments

In reply to Nishanth Menon

Removes the largely duplicated A53 and R5 defconfigs and reuses the am62x_evm_*_defconfig with minor platform specific changes.

---
New Patch

This depends on the RFC (and hence "TMP") and debated upon patch (to introduce config fragments)
https://lore.kernel.org/all/[email protected]/

But this can be fixed up if the fragments support is getting into master (even if buildman follows later).

 board/ti/am62x/beagleplay_a53.config   |  20 +++++
 board/ti/am62x/beagleplay_r5.config    |  11 +++
 configs/am62x_beagleplay_a53_defconfig |  90 --------------------
 configs/am62x_beagleplay_r5_defconfig  | 110 -------------------------
 doc/board/ti/am62x_beagleplay.rst      |   4 +-
 5 files changed, 33 insertions(+), 202 deletions(-)
 create mode 100644 board/ti/am62x/beagleplay_a53.config
 create mode 100644 board/ti/am62x/beagleplay_r5.config
 delete mode 100644 configs/am62x_beagleplay_a53_defconfig
 delete mode 100644 configs/am62x_beagleplay_r5_defconfig
board/ti/am62x/beagleplay_a53.config new file +20 -0
new file mode 100644
index 000000000000..4889e1bc6f2b
@@ -0,0 +1,20 @@
+# Defconfig fragment to apply on top of am62x_evm_a53_defconfig
+
+CONFIG_DEFAULT_DEVICE_TREE="k3-am625-beagleplay"
+CONFIG_OF_LIST="k3-am625-beagleplay"
+CONFIG_SPL_OF_LIST="k3-am625-beagleplay"
+CONFIG_BOOTCOMMAND="run findfdt; run envboot; run distro_bootcmd"
+CONFIG_EXT4_WRITE=y
+CONFIG_LZO=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
+CONFIG_AUTOBOOT_DELAY_STR="d"
+CONFIG_AUTOBOOT_STOP_STR=" "
+# Uses Realtek phy rather than TI phy
+CONFIG_PHY_TI_DP83867=n
+CONFIG_PHY_REALTEK=y
+# No SPI flash on Beagleplay
+CONFIG_SPI=n
+CONFIG_SPI_FLASH=n
+CONFIG_SPL_DM_SPI_FLASH=n
+CONFIG_SPL_SPI_FLASH_SUPPORT=n
board/ti/am62x/beagleplay_r5.config new file +11 -0
new file mode 100644
index 000000000000..ce64561bee92
@@ -0,0 +1,11 @@
+# Defconfig fragment to apply on top of:
+# am62x_evm_r5_defconfig
+#
+CONFIG_DEFAULT_DEVICE_TREE="k3-am625-r5-beagleplay"
+CONFIG_OF_LIST="k3-am625-r5-beagleplay"
+CONFIG_SPL_OF_LIST="k3-am625-r5-beagleplay"
+# No SPI flash on Beagleplay
+CONFIG_SPI=n
+CONFIG_SPI_FLASH=n
+CONFIG_SPL_DM_SPI_FLASH=n
+CONFIG_SPL_SPI_FLASH_SUPPORT=n
configs/am62x_beagleplay_a53_defconfig deleted +0 -90

90 lines not on this page · raw message

configs/am62x_beagleplay_r5_defconfig deleted +0 -110

110 lines not on this page · raw message

doc/board/ti/am62x_beagleplay.rst +2 -2
index b97d8cead7fb..8d9beb68dc98 100644
@@ -55,8 +55,8 @@ Set the variables corresponding to this platform:
     :end-before: .. k3_rst_include_end_common_env_vars_defn
 .. code-block:: bash
 
- $ export UBOOT_CFG_CORTEXR=am62x_beagleplay_r5_defconfig
- $ export UBOOT_CFG_CORTEXA=am62x_beagleplay_a53_defconfig
+ $ export UBOOT_CFG_CORTEXR="am62x_evm_r5_defconfig beagleplay_r5.config"
+ $ export UBOOT_CFG_CORTEXA="am62x_evm_a53_defconfig beagleplay_a53.config"
  $ export TFA_BOARD=lite
  $ # we dont use any extra TFA parameters
  $ unset TFA_EXTRA_ARGS
Signature · 1 line
2.40.0