MIPS: loongson32: Convert all platform devices to DT
Subsystems (6)
Keguang Zhang
maintainercover MIPS: loongson32: Convert all platform devices to DT
Convert all platform devices to devicetree. Remove all the obsolete code of platform device. Adapt the common code to support devicetree. Update Kconfig and Makefile files accordingly. Update and rename the defconfig.
Keguang Zhang (17):
MIPS: loongson32: Get the system type from DT
MIPS: Modify the Loongson1 PRID_REV
MIPS: dts: Add basic DT support for Loongson-1 boards
MIPS: loongson32: Modify Loongson-1B/1C related Kconfig options
MIPS: loongson32: Adapt the common code to support DT
MIPS: loongson32: Convert platform IRQ driver to DT
MIPS: loongson32: Convert UART platform device to DT
MIPS: loongson32: Convert Ethernet platform device to DT
MIPS: loongson32: Convert GPIO platform device to DT
MIPS: loongson32: Convert GPIO LED platform device to DT
MIPS: loongson32: Convert USB host platform device to DT
MIPS: loongson32: Convert RTC platform device to DT
MIPS: loongson32: Convert watchdog platform device to DT
mips: dts: loongson1b: Add PWM timer clocksource
MIPS: loongson32: Remove all the obsolete code of platform device
MIPS: configs: Update and rename loongson1b_defconfig
MIPS: configs: Update and rename loongson1c_defconfig
arch/mips/Kconfig | 62 ++--
arch/mips/boot/dts/Makefile | 1 +
arch/mips/boot/dts/loongson/Makefile | 3 +
arch/mips/boot/dts/loongson/loongson1.dtsi | 161 ++++++++++
arch/mips/boot/dts/loongson/loongson1b.dtsi | 201 ++++++++++++
arch/mips/boot/dts/loongson/loongson1c.dtsi | 144 +++++++++
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 88 ++++++
arch/mips/boot/dts/loongson/smartloong_1c.dts | 84 +++++
...gson1c_defconfig => lsgz_1b_dev_defconfig} | 71 ++++-
...on1b_defconfig => smartloong_1c_defconfig} | 70 ++++-
arch/mips/include/asm/cpu-type.h | 3 +-
arch/mips/include/asm/cpu.h | 3 +-
arch/mips/include/asm/mach-loongson32/dma.h | 21 --
arch/mips/include/asm/mach-loongson32/irq.h | 107 -------
.../include/asm/mach-loongson32/loongson1.h | 50 ---
arch/mips/include/asm/mach-loongson32/nand.h | 26 --
.../include/asm/mach-loongson32/platform.h | 26 --
.../include/asm/mach-loongson32/regs-mux.h | 124 --------
arch/mips/kernel/cpu-probe.c | 6 +-
arch/mips/loongson32/Kconfig | 41 +--
arch/mips/loongson32/Makefile | 14 +-
arch/mips/loongson32/common/Makefile | 6 -
arch/mips/loongson32/common/irq.c | 191 ------------
arch/mips/loongson32/common/platform.c | 287 ------------------
arch/mips/loongson32/common/prom.c | 42 ---
arch/mips/loongson32/common/setup.c | 26 --
arch/mips/loongson32/common/time.c | 23 --
arch/mips/loongson32/init.c | 83 +++++
arch/mips/loongson32/ls1b/Makefile | 6 -
arch/mips/loongson32/ls1b/board.c | 57 ----
arch/mips/loongson32/ls1c/Makefile | 6 -
arch/mips/loongson32/ls1c/board.c | 23 --
arch/mips/loongson32/proc.c | 20 ++
33 files changed, 941 insertions(+), 1135 deletions(-)
create mode 100644 arch/mips/boot/dts/loongson/loongson1.dtsi
create mode 100644 arch/mips/boot/dts/loongson/loongson1b.dtsi
create mode 100644 arch/mips/boot/dts/loongson/loongson1c.dtsi
create mode 100644 arch/mips/boot/dts/loongson/lsgz_1b_dev.dts
create mode 100644 arch/mips/boot/dts/loongson/smartloong_1c.dts
rename arch/mips/configs/{loongson1c_defconfig => lsgz_1b_dev_defconfig} (59%)
rename arch/mips/configs/{loongson1b_defconfig => smartloong_1c_defconfig} (59%)
delete mode 100644 arch/mips/include/asm/mach-loongson32/dma.h
delete mode 100644 arch/mips/include/asm/mach-loongson32/irq.h
delete mode 100644 arch/mips/include/asm/mach-loongson32/loongson1.h
delete mode 100644 arch/mips/include/asm/mach-loongson32/nand.h
delete mode 100644 arch/mips/include/asm/mach-loongson32/platform.h
delete mode 100644 arch/mips/include/asm/mach-loongson32/regs-mux.h
delete mode 100644 arch/mips/loongson32/common/Makefile
delete mode 100644 arch/mips/loongson32/common/irq.c
delete mode 100644 arch/mips/loongson32/common/platform.c
delete mode 100644 arch/mips/loongson32/common/prom.c
delete mode 100644 arch/mips/loongson32/common/setup.c
delete mode 100644 arch/mips/loongson32/common/time.c
create mode 100644 arch/mips/loongson32/init.c
delete mode 100644 arch/mips/loongson32/ls1b/Makefile
delete mode 100644 arch/mips/loongson32/ls1b/board.c
delete mode 100644 arch/mips/loongson32/ls1c/Makefile
delete mode 100644 arch/mips/loongson32/ls1c/board.c
create mode 100644 arch/mips/loongson32/proc.cbase-commit: f11a9967413281b49690d864795e7c5f8f8e4fda
Signature · 1 line
2.39.2
Keguang Zhang
maintainerPATCH 1/17 MIPS: loongson32: Get the system type from DT
Get the system type from devicetree.
And update the copyright accordingly.
In addition, the system type belongs to proc info. So rename setup.c to proc.c.
--- arch/mips/loongson32/Makefile | 1 + arch/mips/loongson32/common/Makefile | 2 +- arch/mips/loongson32/common/setup.c | 26 -------------------------- arch/mips/loongson32/proc.c | 20 ++++++++++++++++++++ 4 files changed, 22 insertions(+), 27 deletions(-) delete mode 100644 arch/mips/loongson32/common/setup.c create mode 100644 arch/mips/loongson32/proc.c
arch/mips/loongson32/Makefile +1 -0
@@ -3,6 +3,7 @@ # Common code for all Loongson 1 based systems # +obj-$(CONFIG_MACH_LOONGSON32) += proc.o obj-$(CONFIG_MACH_LOONGSON32) += common/ #
arch/mips/loongson32/common/Makefile +1 -1
@@ -3,4 +3,4 @@ # Makefile for common code of loongson1 based machines. # -obj-y += time.o irq.o platform.o prom.o setup.o +obj-y += time.o irq.o platform.o prom.o
arch/mips/loongson32/common/setup.c deleted +0 -26
@@ -1,26 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* -* Copyright (c) 2011 Zhang, Keguang <[email protected]> -*/ - -#include <linux/io.h> -#include <linux/init.h> -#include <linux/smp.h> -#include <asm/cpu-info.h> -#include <asm/bootinfo.h> - -const char *get_system_type (void ) -{ -unsigned int processor_id = (¤t_cpu_data)->processor_id; - -switch (processor_id &PRID_REV_MASK ) { -case PRID_REV_LOONGSON1B : -#if defined(CONFIG_LOONGSON1_LS1B ) -return "LOONGSON LS1B" ; -#elif defined(CONFIG_LOONGSON1_LS1C ) -return "LOONGSON LS1C" ; -#endif -default : -return "LOONGSON (unknown)" ; - } -}
arch/mips/loongson32/proc.c new file +20 -0
@@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* +* Copyright (c) 2011-2023 Keguang Zhang <[email protected]> +*/ + +#include <linux/of.h> + +#include <asm/bootinfo.h> + +const char *get_system_type (void ) +{ +const char *str; +int err; + + err =of_property_read_string_index (of_root,"compatible" ,1 , &str); +if (!err) +return str; + +return "Unknown" ; +}
Signature · 1 line
2.39.2
Keguang Zhang
maintainerPATCH 2/17 MIPS: Modify the Loongson1 PRID_REV
In reply to Keguang ZhangBecause LS1B and LS1C share the same PRID,
it's reasonable to rename their PRID_REVs to PRID_REV_LOONGSON1.
--- arch/mips/include/asm/cpu.h | 3 +-- arch/mips/kernel/cpu-probe.c | 6 +++--- 2 files changed, 4 insertions(+), 5 deletions(-)
arch/mips/include/asm/cpu.h +1 -2
@@ -248,8 +248,7 @@#define PRID_REV_VR4181A 0x0070/* Same as VR4122 */ #define PRID_REV_VR4130 0x0080#define PRID_REV_34K_V1_0_2 0x0022 -#define PRID_REV_LOONGSON1B 0x0020 -#define PRID_REV_LOONGSON1C 0x0020/* Same as Loongson-1B */ +#define PRID_REV_LOONGSON1 0x0020#define PRID_REV_LOONGSON2E 0x0002#define PRID_REV_LOONGSON2F 0x0003#define PRID_REV_LOONGSON2K_R1_0 0x0000
arch/mips/kernel/cpu-probe.c +3 -3
@@ -1287,14 +1287,14 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)set_cpu_asid_mask (c,MIPS_ENTRYHI_ASID ); c->writecombine = _CACHE_UNCACHED_ACCELERATED;break ; -case PRID_IMP_LOONGSON_32 :/* Loongson-1 */ +case PRID_IMP_LOONGSON_32 :decode_configs (c); c->cputype =CPU_LOONGSON32 ;switch (c->processor_id &PRID_REV_MASK ) { -case PRID_REV_LOONGSON1B : - __cpu_name[cpu] ="Loongson 1B" ; +case PRID_REV_LOONGSON1 : + __cpu_name[cpu] ="ICT Loongson-1" ;break ; }
Signature · 1 line
2.39.2
Re: [PATCH 02/17] MIPS: Modify the Loongson1 PRID_REV
Quoted 8 lines · Keguang Zhang
Because LS1B and LS1C share the same PRID,
it's reasonable to rename theirPRID_REVstoPRID_REV_LOONGSON1.Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/include/asm/cpu.h | 3 +-- arch/mips/kernel/cpu-probe.c | 6 +++--- 2 files changed, 4 insertions(+), 5 deletions(-)
Keguang Zhang
maintainerPATCH 3/17 MIPS: dts: Add basic DT support for Loongson-1 boards
In reply to Keguang ZhangAdd initial devicetree for Loongson-1 boards, including LSGZ_1B_DEV and SMARTLOONG_1C board.
These basic DTs contain CPU, clock and core INTC.
--- arch/mips/boot/dts/Makefile | 1 + arch/mips/boot/dts/loongson/Makefile | 3 + arch/mips/boot/dts/loongson/loongson1.dtsi | 22 ++++++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 75 +++++++++++++++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 29 +++++++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 25 +++++++ arch/mips/boot/dts/loongson/smartloong_1c.dts | 25 +++++++ 7 files changed, 180 insertions(+) create mode 100644 arch/mips/boot/dts/loongson/loongson1.dtsi create mode 100644 arch/mips/boot/dts/loongson/loongson1b.dtsi create mode 100644 arch/mips/boot/dts/loongson/loongson1c.dtsi create mode 100644 arch/mips/boot/dts/loongson/lsgz_1b_dev.dts create mode 100644 arch/mips/boot/dts/loongson/smartloong_1c.dts
arch/mips/boot/dts/Makefile +1 -0
@@ -6,6 +6,7 @@ subdir-$(CONFIG_FIT_IMAGE_FDT_BOSTON) += img subdir-$(CONFIG_MACH_INGENIC) += ingenic subdir-$(CONFIG_LANTIQ) += lantiq subdir-$(CONFIG_MACH_LOONGSON64) += loongson +subdir-$(CONFIG_MACH_LOONGSON32) += loongson subdir-$(CONFIG_SOC_VCOREIII) += mscc subdir-$(CONFIG_MIPS_MALTA) += mti subdir-$(CONFIG_LEGACY_BOARD_SEAD3) += mti
arch/mips/boot/dts/loongson/Makefile +3 -0
@@ -6,4 +6,7 @@ dtb-$(CONFIG_MACH_LOONGSON64) += loongson64c_8core_rs780e.dtb dtb-$(CONFIG_MACH_LOONGSON64) += loongson64g_4core_ls7a.dtb dtb-$(CONFIG_MACH_LOONGSON64) += loongson64v_4core_virtio.dtb +dtb-$(CONFIG_LOONGSON1B_LSGZ_DEV) += lsgz_1b_dev.dtb +dtb-$(CONFIG_LOONGSON1C_SMARTLOONG) += smartloong_1c.dtb + obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
arch/mips/boot/dts/loongson/loongson1.dtsi new file +22 -0
@@ -0,0 +1,22 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; + +#include <dt-bindings/clock/loongson,ls1x-clk.h> +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + #address-cells = <1>; + #size-cells = <1>; + + cpu_intc: interrupt-controller { + compatible = "mti,cpu-interrupt-controller"; + #address-cells = <0>; + + interrupt-controller; + #interrupt-cells = <1>; + }; +};
arch/mips/boot/dts/loongson/loongson1b.dtsi new file +75 -0
75 lines not on this page · raw message
arch/mips/boot/dts/loongson/loongson1c.dtsi new file +29 -0
@@ -0,0 +1,29 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; +#include "loongson1.dtsi" + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + reg = <0>; + #clock-cells = <1>; + clocks = <&clkc LS1X_CLKID_CPU>; + }; + }; + + clkc: clock-controller@1fe78030 { + compatible = "loongson,ls1c-clk"; + reg = <0x1fe78030 0x8>; + + clocks = <&xtal>; + #clock-cells = <1>; + }; +};
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts new file +25 -0
@@ -0,0 +1,25 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; + +#include "loongson1b.dtsi" + +/ { + compatible = "loongson,lsgz-1b-dev", "loongson,ls1b"; + model = "LSGZ_1B_DEV Board"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; + }; + + xtal: xtal { + compatible = "fixed-clock"; + clock-frequency = <33000000>; + clock-output-names = "xtal"; + #clock-cells = <0>; + }; +};
arch/mips/boot/dts/loongson/smartloong_1c.dts new file +25 -0
@@ -0,0 +1,25 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; + +#include "loongson1c.dtsi" + +/ { + compatible = "loongmasses,smartloong-1c", "loongson,ls1c"; + model = "Smartloong_1C Board"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x2000000>; + }; + + xtal: xtal { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "xtal"; + #clock-cells = <0>; + }; +};
Signature · 1 line
2.39.2
Re: [PATCH 03/17] MIPS: dts: Add basic DT support for Loongson-1 boards
Quoted 204 lines · Keguang Zhang <[email protected]> 于2023年7月29日周六 21:45写道:
Add initial devicetree for Loongson-1 boards, including
LSGZ_1B_DEVandSMARTLOONG_1Cboard.
These basic DTs contain CPU, clock and core INTC.Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/Makefile | 1 + arch/mips/boot/dts/loongson/Makefile | 3 + arch/mips/boot/dts/loongson/loongson1.dtsi | 22 ++++++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 75 +++++++++++++++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 29 +++++++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 25 +++++++ arch/mips/boot/dts/loongson/smartloong_1c.dts | 25 +++++++ 7 files changed, 180 insertions(+) create mode 100644 arch/mips/boot/dts/loongson/loongson1.dtsi create mode 100644 arch/mips/boot/dts/loongson/loongson1b.dtsi create mode 100644 arch/mips/boot/dts/loongson/loongson1c.dtsi create mode 100644 arch/mips/boot/dts/loongson/lsgz_1b_dev.dts create mode 100644 arch/mips/boot/dts/loongson/smartloong_1c.dtsarch/mips/boot/dts/Makefile +1
-0@@ -6,6 +6,7 @@ subdir-$(CONFIG_FIT_IMAGE_FDT_BOSTON) += img subdir-$(CONFIG_MACH_INGENIC) += ingenic subdir-$(CONFIG_LANTIQ) += lantiq subdir-$(CONFIG_MACH_LOONGSON64) += loongson +subdir-$(CONFIG_MACH_LOONGSON32) += loongson subdir-$(CONFIG_SOC_VCOREIII) += mscc subdir-$(CONFIG_MIPS_MALTA) += mti subdir-$(CONFIG_LEGACY_BOARD_SEAD3) += mtiarch/mips/boot/dts/loongson/Makefile +3
-0@@ -6,4 +6,7 @@ dtb-$(CONFIG_MACH_LOONGSON64) += loongson64c_8core_rs780e.dtb dtb-$(CONFIG_MACH_LOONGSON64) += loongson64g_4core_ls7a.dtb dtb-$(CONFIG_MACH_LOONGSON64) += loongson64v_4core_virtio.dtb +dtb-$(CONFIG_LOONGSON1B_LSGZ_DEV) += lsgz_1b_dev.dtb +dtb-$(CONFIG_LOONGSON1C_SMARTLOONG) += smartloong_1c.dtb + obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))arch/mips/boot/dts/loongson/loongson1.dtsi new file +22
-0@@ -0,0 +1,22 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; + +#include <dt-bindings/clock/loongson,ls1x-clk.h> +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + #address-cells = <1>; + #size-cells = <1>; + + cpu_intc: interrupt-controller { + compatible = "mti,cpu-interrupt-controller"; + #address-cells = <0>; + + interrupt-controller; + #interrupt-cells = <1>; + }; +};arch/mips/boot/dts/loongson/loongson1b.dtsi new file +75
-0@@ -0,0 +1,75 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; +#include "loongson1.dtsi" + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + reg = <0>; + #clock-cells = <1>; + clocks = <&clkc LS1X_CLKID_CPU>; + operating-points-v2 = <&cpu_opp_table>; + }; + }; + + cpu_opp_table: opp-table { + compatible = "operating-points-v2"; + opp-shared; + + opp-44000000 { + opp-hz = /bits/ 64 <44000000>; + }; + opp-47142000 { + opp-hz = /bits/ 64 <47142000>; + }; + opp-50769000 { + opp-hz = /bits/ 64 <50769000>; + }; + opp-55000000 { + opp-hz = /bits/ 64 <55000000>; + }; + opp-60000000 { + opp-hz = /bits/ 64 <60000000>; + }; + opp-66000000 { + opp-hz = /bits/ 64 <66000000>; + }; + opp-73333000 { + opp-hz = /bits/ 64 <73333000>; + }; + opp-82500000 { + opp-hz = /bits/ 64 <82500000>; + }; + opp-94285000 { + opp-hz = /bits/ 64 <94285000>; + }; + opp-110000000 { + opp-hz = /bits/ 64 <110000000>; + }; + opp-132000000 { + opp-hz = /bits/ 64 <132000000>; + }; + opp-165000000 { + opp-hz = /bits/ 64 <165000000>; + }; + opp-220000000 { + opp-hz = /bits/ 64 <220000000>; + }; + }; + + clkc: clock-controller@1fe78030 { + compatible = "loongson,ls1b-clk"; + reg = <0x1fe78030 0x8>; + + clocks = <&xtal>; + #clock-cells = <1>; + }; +};arch/mips/boot/dts/loongson/loongson1c.dtsi new file +29
-0@@ -0,0 +1,29 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; +#include "loongson1.dtsi" + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + reg = <0>; + #clock-cells = <1>; + clocks = <&clkc LS1X_CLKID_CPU>; + }; + }; + + clkc: clock-controller@1fe78030 { + compatible = "loongson,ls1c-clk"; + reg = <0x1fe78030 0x8>; + + clocks = <&xtal>; + #clock-cells = <1>; + }; +};arch/mips/boot/dts/loongson/lsgz_1b_dev.dts new file +9
-0@@ -0,0 +1,25 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; + +#include "loongson1b.dtsi" +
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts line 19
Quoted 10 lines
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts new file +10
-0+/ { + compatible = "loongson,lsgz-1b-dev", "loongson,ls1b"; + model = "LSGZ_1B_DEV Board"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; + }; + + xtal: xtal {
for your information, hope it helps:
in <devicetree-specification-v0.4.pdf> Page: 8
The name of a node should be somewhat generic, reflecting the function of the device and not its precise programming model. If appropriate,
the name should be one of the following choices:
... clock ...
Quoted 38 lines
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts new file +6
-0+ compatible = "fixed-clock"; + clock-frequency = <33000000>; + clock-output-names = "xtal"; + #clock-cells = <0>; + }; +};arch/mips/boot/dts/loongson/smartloong_1c.dts new file +25
-1@@ -0,0 +1,25 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; + +#include "loongson1c.dtsi" + +/ { + compatible = "loongmasses,smartloong-1c", "loongson,ls1c"; + model = "Smartloong_1C Board"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x2000000>; + }; + + xtal: xtal { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "xtal"; + #clock-cells = <0>; + }; +}; --
Quoted 2 lines
2.39.2
---
Du Huanpeng
Keguang Zhang
maintainerRe: [PATCH 03/17] MIPS: dts: Add basic DT support for Loongson-1 boards
Quoted 214 lines · Du Huanpeng
Quoted 212 lines · Keguang Zhang <[email protected]> 于2023年7月29日周六 21:45写道:
Add initial devicetree for Loongson-1 boards, including
LSGZ_1B_DEVandSMARTLOONG_1Cboard.
These basic DTs contain CPU, clock and core INTC.Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/Makefile | 1 + arch/mips/boot/dts/loongson/Makefile | 3 + arch/mips/boot/dts/loongson/loongson1.dtsi | 22 ++++++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 75 +++++++++++++++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 29 +++++++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 25 +++++++ arch/mips/boot/dts/loongson/smartloong_1c.dts | 25 +++++++ 7 files changed, 180 insertions(+) create mode 100644 arch/mips/boot/dts/loongson/loongson1.dtsi create mode 100644 arch/mips/boot/dts/loongson/loongson1b.dtsi create mode 100644 arch/mips/boot/dts/loongson/loongson1c.dtsi create mode 100644 arch/mips/boot/dts/loongson/lsgz_1b_dev.dts create mode 100644 arch/mips/boot/dts/loongson/smartloong_1c.dtsarch/mips/boot/dts/Makefile +1
-0@@ -6,6 +6,7 @@ subdir-$(CONFIG_FIT_IMAGE_FDT_BOSTON) += img subdir-$(CONFIG_MACH_INGENIC) += ingenic subdir-$(CONFIG_LANTIQ) += lantiq subdir-$(CONFIG_MACH_LOONGSON64) += loongson +subdir-$(CONFIG_MACH_LOONGSON32) += loongson subdir-$(CONFIG_SOC_VCOREIII) += mscc subdir-$(CONFIG_MIPS_MALTA) += mti subdir-$(CONFIG_LEGACY_BOARD_SEAD3) += mtiarch/mips/boot/dts/loongson/Makefile +3
-0@@ -6,4 +6,7 @@ dtb-$(CONFIG_MACH_LOONGSON64) += loongson64c_8core_rs780e.dtb dtb-$(CONFIG_MACH_LOONGSON64) += loongson64g_4core_ls7a.dtb dtb-$(CONFIG_MACH_LOONGSON64) += loongson64v_4core_virtio.dtb +dtb-$(CONFIG_LOONGSON1B_LSGZ_DEV) += lsgz_1b_dev.dtb +dtb-$(CONFIG_LOONGSON1C_SMARTLOONG) += smartloong_1c.dtb + obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))arch/mips/boot/dts/loongson/loongson1.dtsi new file +22
-0@@ -0,0 +1,22 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; + +#include <dt-bindings/clock/loongson,ls1x-clk.h> +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + #address-cells = <1>; + #size-cells = <1>; + + cpu_intc: interrupt-controller { + compatible = "mti,cpu-interrupt-controller"; + #address-cells = <0>; + + interrupt-controller; + #interrupt-cells = <1>; + }; +};arch/mips/boot/dts/loongson/loongson1b.dtsi new file +75
-0@@ -0,0 +1,75 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; +#include "loongson1.dtsi" + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + reg = <0>; + #clock-cells = <1>; + clocks = <&clkc LS1X_CLKID_CPU>; + operating-points-v2 = <&cpu_opp_table>; + }; + }; + + cpu_opp_table: opp-table { + compatible = "operating-points-v2"; + opp-shared; + + opp-44000000 { + opp-hz = /bits/ 64 <44000000>; + }; + opp-47142000 { + opp-hz = /bits/ 64 <47142000>; + }; + opp-50769000 { + opp-hz = /bits/ 64 <50769000>; + }; + opp-55000000 { + opp-hz = /bits/ 64 <55000000>; + }; + opp-60000000 { + opp-hz = /bits/ 64 <60000000>; + }; + opp-66000000 { + opp-hz = /bits/ 64 <66000000>; + }; + opp-73333000 { + opp-hz = /bits/ 64 <73333000>; + }; + opp-82500000 { + opp-hz = /bits/ 64 <82500000>; + }; + opp-94285000 { + opp-hz = /bits/ 64 <94285000>; + }; + opp-110000000 { + opp-hz = /bits/ 64 <110000000>; + }; + opp-132000000 { + opp-hz = /bits/ 64 <132000000>; + }; + opp-165000000 { + opp-hz = /bits/ 64 <165000000>; + }; + opp-220000000 { + opp-hz = /bits/ 64 <220000000>; + }; + }; + + clkc: clock-controller@1fe78030 { + compatible = "loongson,ls1b-clk"; + reg = <0x1fe78030 0x8>; + + clocks = <&xtal>; + #clock-cells = <1>; + }; +};arch/mips/boot/dts/loongson/loongson1c.dtsi new file +29
-0@@ -0,0 +1,29 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; +#include "loongson1.dtsi" + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + reg = <0>; + #clock-cells = <1>; + clocks = <&clkc LS1X_CLKID_CPU>; + }; + }; + + clkc: clock-controller@1fe78030 { + compatible = "loongson,ls1c-clk"; + reg = <0x1fe78030 0x8>; + + clocks = <&xtal>; + #clock-cells = <1>; + }; +};arch/mips/boot/dts/loongson/lsgz_1b_dev.dts new file +17
-0@@ -0,0 +1,25 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; + +#include "loongson1b.dtsi" + +/ { + compatible = "loongson,lsgz-1b-dev", "loongson,ls1b"; + model = "LSGZ_1B_DEV Board"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; + };
Quoted 9 lines
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts line 19
Quoted 2 lines
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts new file +2
-0+ + xtal: xtal {for your information, hope it helps:
in <devicetree-specification-v0.4.pdf> Page: 8
The name of a node should be somewhat generic, reflecting the function of the device and not its precise programming model. If appropriate,
the name should be one of the following choices:
... clock ...
Will fix this.
Thanks!
Quoted 43 lines
Quoted 38 lines
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts new file +6
-0+ compatible = "fixed-clock"; + clock-frequency = <33000000>; + clock-output-names = "xtal"; + #clock-cells = <0>; + }; +};arch/mips/boot/dts/loongson/smartloong_1c.dts new file +25
-1@@ -0,0 +1,25 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2023 Keguang Zhang <[email protected]> + */ + +/dts-v1/; + +#include "loongson1c.dtsi" + +/ { + compatible = "loongmasses,smartloong-1c", "loongson,ls1c"; + model = "Smartloong_1C Board"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x2000000>; + }; + + xtal: xtal { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "xtal"; + #clock-cells = <0>; + }; +}; --Quoted 2 lines
2.39.2
---
Du Huanpeng
Signature · 3 lines
Best regards, Keguang Zhang
Keguang Zhang
maintainerPATCH 4/17 MIPS: loongson32: Modify Loongson-1B/1C related Kconfig options
In reply to Keguang ZhangCPU_LOONGSON1B and CPU_LOONGSON1C have the same GS232 core, so merge them into CPU_LOONGSON32.
The Kconfig options selected by LOONGSON1_LS1B and LOONGSON1_LS1C is selected by MACH_LOONGSON32 now.
And LOONGSON1_LS1B and LOONGSON1_LS1C will be deleted after all platform devices are converted to devicetree nodes.
Introduce MACH_LSGZ_1B_DEV and MACH_SMARTLOONG_1C
for the built-in DTS selection.
Partialy based on the patch by Jiaxun Yang.
--- arch/mips/Kconfig | 62 ++++++++++++++-------------- arch/mips/boot/dts/loongson/Makefile | 4 +- arch/mips/include/asm/cpu-type.h | 3 +- arch/mips/loongson32/Kconfig | 47 ++++++++------------- 4 files changed, 50 insertions(+), 66 deletions(-)
arch/mips/Kconfig +30 -32
@@ -466,6 +466,21 @@ config LANTIQ config MACH_LOONGSON32 bool "Loongson 32-bit family of machines" + select USE_OF + select BUILTIN_DTB + select BOOT_ELF32 + select CEVT_R4K + select CSRC_R4K + select COMMON_CLK + select DMA_NONCOHERENT + select IRQ_MIPS_CPU + select LS1X_IRQ + select SYS_HAS_CPU_LOONGSON32 + select SYS_HAS_EARLY_PRINTK + select USE_GENERIC_EARLY_PRINTK_8250 + select SYS_SUPPORTS_32BIT_KERNEL + select SYS_SUPPORTS_LITTLE_ENDIAN + select SYS_SUPPORTS_HIGHMEM select SYS_SUPPORTS_ZBOOT help This enables support for the Loongson-1 family of machines.
@@ -1350,25 +1365,20 @@ config CPU_LOONGSON2F have a similar programming interface with FPGA northbridge used in Loongson2E. -config CPU_LOONGSON1B - bool "Loongson 1B" - depends on SYS_HAS_CPU_LOONGSON1B - select CPU_LOONGSON32 - select LEDS_GPIO_REGISTER - help - The Loongson 1B is a 32-bit SoC, which implements the MIPS32 - Release 1 instruction set and part of the MIPS32 Release 2 - instruction set. - -config CPU_LOONGSON1C - bool "Loongson 1C" - depends on SYS_HAS_CPU_LOONGSON1C - select CPU_LOONGSON32 +config CPU_LOONGSON32 + bool "Loongson 32-bit CPU" + depends on SYS_HAS_CPU_LOONGSON32 + select CPU_MIPS32 + select CPU_MIPSR2 + select CPU_HAS_PREFETCH + select CPU_HAS_LOAD_STORE_LR + select CPU_SUPPORTS_32BIT_KERNEL + select CPU_SUPPORTS_HIGHMEM + select CPU_SUPPORTS_CPUFREQ select LEDS_GPIO_REGISTER help - The Loongson 1C is a 32-bit SoC, which implements the MIPS32 - Release 1 instruction set and part of the MIPS32 Release 2 - instruction set. + The Loongson GS232 microarchitecture implements the MIPS32 Release 1 + instruction set and part of the MIPS32 Release 2 instruction set. config CPU_MIPS32_R1 bool "MIPS32 Release 1"
@@ -1764,15 +1774,6 @@ config CPU_LOONGSON2EF select CPU_SUPPORTS_HIGHMEM select CPU_SUPPORTS_HUGEPAGES -config CPU_LOONGSON32 - bool - select CPU_MIPS32 - select CPU_MIPSR2 - select CPU_HAS_PREFETCH - select CPU_SUPPORTS_32BIT_KERNEL - select CPU_SUPPORTS_HIGHMEM - select CPU_SUPPORTS_CPUFREQ - config CPU_BMIPS32_3300 select SMP_UP if SMP bool
@@ -1810,10 +1811,7 @@ config SYS_HAS_CPU_LOONGSON2F select CPU_SUPPORTS_CPUFREQ select CPU_SUPPORTS_ADDRWINCFG if 64BIT -config SYS_HAS_CPU_LOONGSON1B - bool - -config SYS_HAS_CPU_LOONGSON1C +config SYS_HAS_CPU_LOONGSON32 bool config SYS_HAS_CPU_MIPS32_R1
@@ -2996,8 +2994,8 @@ endchoice choice prompt "Kernel command line type" if !CMDLINE_OVERRIDE default MIPS_CMDLINE_FROM_DTB if USE_OF && !ATH79 && !MACH_INGENIC && \ - !MACH_LOONGSON64 && !MIPS_MALTA && \ - !CAVIUM_OCTEON_SOC + !MACH_LOONGSON64 && !MACH_LOONGSON32 && \ + !MIPS_MALTA && !CAVIUM_OCTEON_SOC default MIPS_CMDLINE_FROM_BOOTLOADER config MIPS_CMDLINE_FROM_DTB
arch/mips/boot/dts/loongson/Makefile +2 -2
@@ -6,7 +6,7 @@ dtb-$(CONFIG_MACH_LOONGSON64) += loongson64c_8core_rs780e.dtb dtb-$(CONFIG_MACH_LOONGSON64) += loongson64g_4core_ls7a.dtb dtb-$(CONFIG_MACH_LOONGSON64) += loongson64v_4core_virtio.dtb -dtb-$(CONFIG_LOONGSON1B_LSGZ_DEV) += lsgz_1b_dev.dtb -dtb-$(CONFIG_LOONGSON1C_SMARTLOONG) += smartloong_1c.dtb +dtb-$(CONFIG_MACH_LSGZ_1B_DEV) += lsgz_1b_dev.dtb +dtb-$(CONFIG_MACH_SMARTLOONG_1C) += smartloong_1c.dtb obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
arch/mips/include/asm/cpu-type.h +1 -2
@@ -24,8 +24,7 @@ static inline int __pure __get_cpu_type(const int cpu_type)case CPU_LOONGSON64 :#endif -#if defined(CONFIG_SYS_HAS_CPU_LOONGSON1B ) || \ - defined(CONFIG_SYS_HAS_CPU_LOONGSON1C ) +#ifdef CONFIG_SYS_HAS_CPU_LOONGSON32 case CPU_LOONGSON32 :#endif
arch/mips/loongson32/Kconfig +17 -30
55 lines not on this page · raw message
Signature · 1 line
2.39.2
Keguang Zhang
maintainerPATCH 5/17 MIPS: loongson32: Adapt the common code to support DT
In reply to Keguang ZhangAdapt the initial functions to support devicetree. And introduce init.c to collect these initial functions.
--- arch/mips/loongson32/Makefile | 2 +- arch/mips/loongson32/common/Makefile | 2 +- arch/mips/loongson32/common/prom.c | 42 --------------- arch/mips/loongson32/common/time.c | 23 -------- arch/mips/loongson32/init.c | 78 ++++++++++++++++++++++++++++ 5 files changed, 80 insertions(+), 67 deletions(-) delete mode 100644 arch/mips/loongson32/common/prom.c delete mode 100644 arch/mips/loongson32/common/time.c create mode 100644 arch/mips/loongson32/init.c
arch/mips/loongson32/Makefile +1 -1
@@ -3,7 +3,7 @@ # Common code for all Loongson 1 based systems # -obj-$(CONFIG_MACH_LOONGSON32) += proc.o +obj-$(CONFIG_MACH_LOONGSON32) += init.o proc.o obj-$(CONFIG_MACH_LOONGSON32) += common/ #
arch/mips/loongson32/common/Makefile +1 -1
@@ -3,4 +3,4 @@ # Makefile for common code of loongson1 based machines. # -obj-y += time.o irq.o platform.o prom.o +obj-y += irq.o platform.o
arch/mips/loongson32/common/prom.c deleted +0 -42
42 lines not on this page · raw message
arch/mips/loongson32/common/time.c deleted +0 -23
@@ -1,23 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* -* Copyright (c) 2014 Zhang, Keguang <[email protected]> -*/ - -#include <linux/clk.h> -#include <linux/of_clk.h> -#include <asm/time.h> - -void __init plat_time_init (void ) -{ -struct clk *clk =NULL ; - -/* initialize LS1X clocks */ -of_clk_init (NULL ); - -/* setup mips r4k timer */ - clk =clk_get (NULL ,"cpu_clk" ); -if (IS_ERR (clk)) -panic ("unable to get cpu clock, err=%ld" ,PTR_ERR (clk)); - - mips_hpt_frequency =clk_get_rate (clk) /2 ; -}
arch/mips/loongson32/init.c new file +78 -0
78 lines not on this page · raw message
Signature · 1 line
2.39.2
Keguang Zhang
maintainerPATCH 6/17 MIPS: loongson32: Convert platform IRQ driver to DT
In reply to Keguang ZhangThis patch enables Loongson-1 irqchip driver by adding platform INTC device nodes.
And drop the legacy platform IRQ driver accordingly.
Based on previous patch by Jiaxun Yang.
--- arch/mips/boot/dts/loongson/loongson1.dtsi | 53 ++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 13 ++ arch/mips/loongson32/common/Makefile | 2 +- arch/mips/loongson32/common/irq.c | 191 -------------------- arch/mips/loongson32/init.c | 5 + 5 files changed, 72 insertions(+), 192 deletions(-) delete mode 100644 arch/mips/loongson32/common/irq.c
arch/mips/boot/dts/loongson/loongson1.dtsi +53 -0
@@ -19,4 +19,57 @@ cpu_intc: interrupt-controller { interrupt-controller; #interrupt-cells = <1>; }; + + ahb: bus@1f000000 { + compatible = "simple-bus"; + reg = <0x1f000000 0xe40000>; + ranges; + + #address-cells = <1>; + #size-cells = <1>; + + intc0: interrupt-controller@1fd01040 { + compatible = "loongson,ls1x-intc"; + reg = <0x1fd01040 0x18>; + + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&cpu_intc>; + interrupts = <2>; + }; + + intc1: interrupt-controller@1fd01058 { + compatible = "loongson,ls1x-intc"; + reg = <0x1fd01058 0x18>; + + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&cpu_intc>; + interrupts = <3>; + }; + + intc2: interrupt-controller@1fd01070 { + compatible = "loongson,ls1x-intc"; + reg = <0x1fd01070 0x18>; + + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&cpu_intc>; + interrupts = <4>; + }; + + intc3: interrupt-controller@1fd01088 { + compatible = "loongson,ls1x-intc"; + reg = <0x1fd01088 0x18>; + + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&cpu_intc>; + interrupts = <5>; + }; + }; };
arch/mips/boot/dts/loongson/loongson1c.dtsi +13 -0
@@ -27,3 +27,16 @@ clkc: clock-controller@1fe78030 { #clock-cells = <1>; }; }; + +&ahb { + intc4: interrupt-controller@1fd010a0 { + compatible = "loongson,ls1x-intc"; + reg = <0x1fd010a0 0x18>; + + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&cpu_intc>; + interrupts = <6>; + }; +};
arch/mips/loongson32/common/Makefile +1 -1
@@ -3,4 +3,4 @@ # Makefile for common code of loongson1 based machines. # -obj-y += irq.o platform.o +obj-y += platform.o
arch/mips/loongson32/common/irq.c deleted +0 -191
191 lines not on this page · raw message
arch/mips/loongson32/init.c +5 -0
@@ -76,3 +76,8 @@ void __init plat_time_init(void)timer_probe (); } + +void __init arch_init_irq (void ) +{ +irqchip_init (); +}
Signature · 1 line
2.39.2
Re: [PATCH 06/17] MIPS: loongson32: Convert platform IRQ driver to DT
Quoted 11 lines · Keguang Zhang
This patch enables Loongson-1 irqchip driver by adding platform INTC device nodes.
And drop the legacy platform IRQ driver accordingly.Based on previous patch by Jiaxun Yang.
Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 53 ++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 13 ++
DTS is always separate from the drivers.
Quoted 6 lines
arch/mips/loongson32/common/Makefile | 2 +- arch/mips/loongson32/common/irq.c | 191 -------------------- arch/mips/loongson32/init.c | 5 + 5 files changed, 72 insertions(+), 192 deletions(-) delete mode 100644 arch/mips/loongson32/common/irq.c
Best regards,
Krzysztof
Keguang Zhang
maintainerRe: [PATCH 06/17] MIPS: loongson32: Convert platform IRQ driver to DT
Quoted 8 lines · Krzysztof Kozlowski
Quoted 6 lines · Keguang Zhang
This patch enables Loongson-1 irqchip driver by adding platform INTC device nodes.
And drop the legacy platform IRQ driver accordingly.Based on previous patch by Jiaxun Yang.
Quoted 7 lines
Quoted 5 lines
Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 53 ++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 13 ++DTS is always separate from the drivers.
Got it. Will do.
Quoted 13 lines
Quoted 7 lines
arch/mips/loongson32/common/Makefile | 2 +- arch/mips/loongson32/common/irq.c | 191 -------------------- arch/mips/loongson32/init.c | 5 + 5 files changed, 72 insertions(+), 192 deletions(-) delete mode 100644 arch/mips/loongson32/common/irq.cBest regards,
Krzysztof
Signature · 3 lines
Best regards, Keguang Zhang
Keguang Zhang
maintainerPATCH 7/17 MIPS: loongson32: Convert UART platform device to DT
In reply to Keguang ZhangAdd UART device nodes for Loongson-1 boards,
and drop the legacy platform devices and data accordingly.
--- arch/mips/boot/dts/loongson/loongson1.dtsi | 54 +++++++++++++++++++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 12 +++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 12 +++++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 20 +++++++ arch/mips/boot/dts/loongson/smartloong_1c.dts | 20 +++++++ arch/mips/loongson32/common/platform.c | 44 --------------- arch/mips/loongson32/ls1b/board.c | 3 -- arch/mips/loongson32/ls1c/board.c | 3 -- 8 files changed, 118 insertions(+), 50 deletions(-)
arch/mips/boot/dts/loongson/loongson1.dtsi +54 -0
@@ -72,4 +72,58 @@ intc3: interrupt-controller@1fd01088 { interrupts = <5>; }; }; + + apb: bus@1fe40000 { + compatible = "simple-bus"; + reg = <0x1fe40000 0x40000>; + ranges; + + #address-cells = <1>; + #size-cells = <1>; + + uart0: serial@1fe40000 { + compatible = "ns16550a"; + reg = <0x1fe40000 0x8>; + + interrupt-parent = <&intc0>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&clkc LS1X_CLKID_APB>; + + status = "disabled"; + }; + + uart1: serial@1fe44000 { + compatible = "ns16550a"; + reg = <0x1fe44000 0x8>; + + interrupt-parent = <&intc0>; + + clocks = <&clkc LS1X_CLKID_APB>; + + status = "disabled"; + }; + + uart2: serial@1fe48000 { + compatible = "ns16550a"; + reg = <0x1fe48000 0x8>; + + interrupt-parent = <&intc0>; + + clocks = <&clkc LS1X_CLKID_APB>; + + status = "disabled"; + }; + + uart3: serial@1fe4c000 { + compatible = "ns16550a"; + reg = <0x1fe4c000 0x8>; + + interrupt-parent = <&intc0>; + + clocks = <&clkc LS1X_CLKID_APB>; + + status = "disabled"; + }; + }; };
arch/mips/boot/dts/loongson/loongson1b.dtsi +12 -0
@@ -73,3 +73,15 @@ clkc: clock-controller@1fe78030 { #clock-cells = <1>; }; }; + +&uart1 { + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; +}; + +&uart2 { + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; +}; + +&uart3 { + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; +};
arch/mips/boot/dts/loongson/loongson1c.dtsi +12 -0
@@ -40,3 +40,15 @@ intc4: interrupt-controller@1fd010a0 { interrupts = <6>; }; }; + +&uart1 { + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; +}; + +&uart2 { + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; +}; + +&uart3 { + interrupts = <29 IRQ_TYPE_LEVEL_HIGH>; +};
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +20 -0
@@ -11,6 +11,10 @@ / { compatible = "loongson,lsgz-1b-dev", "loongson,ls1b"; model = "LSGZ_1B_DEV Board"; + chosen { + bootargs = "console=ttyS2,115200"; + }; + memory@0 { device_type = "memory"; reg = <0x0 0x4000000>;
@@ -23,3 +27,19 @@ xtal: xtal { #clock-cells = <0>; }; }; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +};
arch/mips/boot/dts/loongson/smartloong_1c.dts +20 -0
@@ -11,6 +11,10 @@ / { compatible = "loongmasses,smartloong-1c", "loongson,ls1c"; model = "Smartloong_1C Board"; + chosen { + bootargs = "console=ttyS2,115200"; + }; + memory@0 { device_type = "memory"; reg = <0x0 0x2000000>;
@@ -23,3 +27,19 @@ xtal: xtal { #clock-cells = <0>; }; }; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +};
arch/mips/loongson32/common/platform.c +0 -44
56 lines not on this page · raw message
arch/mips/loongson32/ls1b/board.c +0 -3
@@ -34,7 +34,6 @@ static const struct gpio_led_platform_data ls1x_led_pdata __initconst = { };static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_uart_pdev, &ls1x_eth0_pdev, &ls1x_eth1_pdev, &ls1x_ehci_pdev,
@@ -46,8 +45,6 @@ static struct platform_device *ls1b_platform_devices[] __initdata = {static int __init ls1b_platform_init (void ) { -ls1x_serial_set_uartclk (&ls1x_uart_pdev); -gpio_led_register_device (-1 , &ls1x_led_pdata); return platform_add_devices(ls1b_platform_devices,
arch/mips/loongson32/ls1c/board.c +0 -3
@@ -6,7 +6,6 @@#include <platform.h> static struct platform_device *ls1c_platform_devices[]__initdata = { - &ls1x_uart_pdev, &ls1x_eth0_pdev, &ls1x_rtc_pdev, &ls1x_wdt_pdev,
@@ -14,8 +13,6 @@ static struct platform_device *ls1c_platform_devices[] __initdata = {static int __init ls1c_platform_init (void ) { -ls1x_serial_set_uartclk (&ls1x_uart_pdev); -return platform_add_devices (ls1c_platform_devices,ARRAY_SIZE (ls1c_platform_devices)); }
Signature · 1 line
2.39.2
Re: [PATCH 07/17] MIPS: loongson32: Convert UART platform device to DT
Quoted 6 lines · Keguang Zhang
Add UART device nodes for Loongson-1 boards,
and drop the legacy platform devices and data accordingly.Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 54 +++++++++++++++++++
Same problem - DTS is always separate. It seems you made this mistake everywhere, so entire patchset needs to be fixed. Keep all DTS - your base board and extending it - at the end of the patchset and squash it. There is little point to add new DTS in steps (e.g. first add incomplete broken DTS and then immediately fix it... no, instead just add correct and complete DTS).
Best regards,
Krzysztof
Keguang Zhang
maintainerRe: [PATCH 07/17] MIPS: loongson32: Convert UART platform device to DT
Quoted 9 lines · Krzysztof Kozlowski
Quoted 6 lines · Keguang Zhang
Add UART device nodes for Loongson-1 boards,
and drop the legacy platform devices and data accordingly.Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 54 +++++++++++++++++++
Quoted 7 lines
Same problem - DTS is always separate. It seems you made this mistake everywhere, so entire patchset needs to be fixed. Keep all DTS - your base board and extending it - at the end of the patchset and squash it. There is little point to add new DTS in steps (e.g. first add incomplete broken DTS and then immediately fix it... no, instead just add correct and complete DTS).
Sorry. I thought it would be easier to review for split patches. Thanks for the explanation.
Will send v2 with one complete DTS.
Quoted 4 lines
Best regards,
Krzysztof
Signature · 3 lines
Best regards, Keguang Zhang
Keguang Zhang
maintainerRe: [PATCH 07/17] MIPS: loongson32: Convert UART platform device to DT
Quoted 19 lines · Keguang Zhang
Quoted 9 lines · Krzysztof Kozlowski
Quoted 6 lines · Keguang Zhang
Add UART device nodes for Loongson-1 boards,
and drop the legacy platform devices and data accordingly.Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 54 +++++++++++++++++++Quoted 7 lines
Same problem - DTS is always separate. It seems you made this mistake everywhere, so entire patchset needs to be fixed. Keep all DTS - your base board and extending it - at the end of the patchset and squash it. There is little point to add new DTS in steps (e.g. first add incomplete broken DTS and then immediately fix it... no, instead just add correct and complete DTS).
Quoted 3 lines
Sorry. I thought it would be easier to review for split patches. Thanks for the explanation.
Will send v2 with one complete DTS.
Hello Thomas,
May I ask your opinion about the way to delete the obsolete platform devices? Should I delete them in one patch? Or in separated patches? Thanks!
Quoted 10 lines
Quoted 4 lines
Best regards,
Krzysztof--
Best regards,Keguang Zhang
Signature · 3 lines
Best regards, Keguang Zhang
Re: [PATCH 07/17] MIPS: loongson32: Convert UART platform device to DT
Quoted 20 lines · Keguang Zhang
Quoted 19 lines · Keguang Zhang
Quoted 16 lines · Krzysztof Kozlowski
Quoted 6 lines · Keguang Zhang
Add UART device nodes for Loongson-1 boards,
and drop the legacy platform devices and data accordingly.Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 54 +++++++++++++++++++Same problem - DTS is always separate. It seems you made this mistake everywhere, so entire patchset needs to be fixed. Keep all DTS - your base board and extending it - at the end of the patchset and squash it. There is little point to add new DTS in steps (e.g. first add incomplete broken DTS and then immediately fix it... no, instead just add correct and complete DTS).
Quoted 7 lines
Quoted 3 lines
Sorry. I thought it would be easier to review for split patches. Thanks for the explanation.
Will send v2 with one complete DTS.Hello Thomas,
May I ask your opinion about the way to delete the obsolete platform devices? Should I delete them in one patch? Or in separated patches?
subsystem patches are split per subsystem. arch-code can be either together or also split per type of driver. Removal of code is incremental. Just add extending it, but your patch was not extending DTS, but adding new one.
Best regards,
Krzysztof
Keguang Zhang
maintainerPATCH 8/17 MIPS: loongson32: Convert Ethernet platform device to DT
In reply to Keguang ZhangAdd Ethernet device nodes for Loongson-1 boards, and drop the legacy platform devices and data accordingly.
--- arch/mips/boot/dts/loongson/loongson1.dtsi | 16 ++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 53 +++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 17 ++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 8 + arch/mips/boot/dts/loongson/smartloong_1c.dts | 4 + arch/mips/loongson32/common/platform.c | 146 +----------------- arch/mips/loongson32/ls1b/board.c | 2 - arch/mips/loongson32/ls1c/board.c | 1 - 8 files changed, 99 insertions(+), 148 deletions(-)
arch/mips/boot/dts/loongson/loongson1.dtsi +16 -0
@@ -71,6 +71,22 @@ intc3: interrupt-controller@1fd01088 { interrupt-parent = <&cpu_intc>; interrupts = <5>; }; + + gmac0: ethernet@1fe10000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe10000 0x10000>; + + interrupt-parent = <&intc1>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + snps,pbl = <1>; + + status = "disabled"; + }; + }; apb: bus@1fe40000 {
arch/mips/boot/dts/loongson/loongson1b.dtsi +53 -0
65 lines not on this page · raw message
arch/mips/boot/dts/loongson/loongson1c.dtsi +17 -0
@@ -41,6 +41,23 @@ intc4: interrupt-controller@1fd010a0 { }; }; +&gmac0 { + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "rmii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@13 { + reg = <0x13>; + }; + }; +}; + &uart1 { interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; };
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +8 -0
@@ -28,6 +28,14 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + +&gmac1 { + status = "okay"; +}; + &uart0 { status = "okay"; };
arch/mips/boot/dts/loongson/smartloong_1c.dts +4 -0
@@ -28,6 +28,10 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + &uart0 { status = "okay"; };
arch/mips/loongson32/common/platform.c +1 -145
158 lines not on this page · raw message
arch/mips/loongson32/ls1b/board.c +0 -2
@@ -34,8 +34,6 @@ static const struct gpio_led_platform_data ls1x_led_pdata __initconst = { };static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_eth0_pdev, - &ls1x_eth1_pdev, &ls1x_ehci_pdev, &ls1x_gpio0_pdev, &ls1x_gpio1_pdev,
arch/mips/loongson32/ls1c/board.c +0 -1
@@ -6,7 +6,6 @@#include <platform.h> static struct platform_device *ls1c_platform_devices[]__initdata = { - &ls1x_eth0_pdev, &ls1x_rtc_pdev, &ls1x_wdt_pdev, };
Signature · 1 line
2.39.2
Re: [PATCH 08/17] MIPS: loongson32: Convert Ethernet platform device to DT
Quoted 2 lines · Keguang Zhang
Add Ethernet device nodes for Loongson-1 boards, and drop the legacy platform devices and data accordingly.
It seems to me that your conversion breaks the RGMII mode support. What you need to do is to make sure that the respective flags are set in the MUX space.
Regarding the MUX-space. It looks as a pinctrl-setting space. If so adding the new pinctrl driver will be required. Otherwise it can be defined as a syscon-node and then utilized in the Loongson-1 GMAC low-level driver.
-Serge(y)
Quoted 364 lines
Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 16 ++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 53 +++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 17 ++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 8 + arch/mips/boot/dts/loongson/smartloong_1c.dts | 4 + arch/mips/loongson32/common/platform.c | 146 +----------------- arch/mips/loongson32/ls1b/board.c | 2 - arch/mips/loongson32/ls1c/board.c | 1 - 8 files changed, 99 insertions(+), 148 deletions(-)arch/mips/boot/dts/loongson/loongson1.dtsi +16
-0@@ -71,6 +71,22 @@ intc3: interrupt-controller@1fd01088 { interrupt-parent = <&cpu_intc>; interrupts = <5>; }; + + gmac0: ethernet@1fe10000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe10000 0x10000>; + + interrupt-parent = <&intc1>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + snps,pbl = <1>; + + status = "disabled"; + }; + }; apb: bus@1fe40000 {arch/mips/boot/dts/loongson/loongson1b.dtsi +53
-0@@ -7,6 +7,11 @@ #include "loongson1.dtsi" / { + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + }; + cpus { #address-cells = <1>; #size-cells = <0>;@@ -74,6 +79,54 @@ clkc: clock-controller@1fe78030 { }; }; +&ahb { + gmac1: ethernet@1fe20000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe20000 0x10000>; + + interrupt-parent = <&intc1>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + phy-handle = <&phy1>; + phy-mode = "mii"; + + snps,pbl = <1>; + + status = "disabled"; + + mdio1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy1: ethernet-phy@0 { + reg = <0x0>; + }; + }; + }; +}; + +&gmac0 { + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "mii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + }; +}; + &uart1 { interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/loongson1c.dtsi +17
-0@@ -41,6 +41,23 @@ intc4: interrupt-controller@1fd010a0 { }; }; +&gmac0 { + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "rmii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@13 { + reg = <0x13>; + }; + }; +}; + &uart1 { interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +8
-0@@ -28,6 +28,14 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + +&gmac1 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/boot/dts/loongson/smartloong_1c.dts +4
-0@@ -28,6 +28,10 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/loongson32/common/platform.c +1
-145@@ -8,157 +8,13 @@#include <linux/err.h> #include <linux/mtd/partitions.h> #include <linux/sizes.h> -#include <linux/phy.h> -#include <linux/stmmac.h> #include <linux/usb/ehci_pdriver.h> #include <platform.h> #include <loongson1.h> #include <dma.h> #include <nand.h> - -/* Synopsys Ethernet GMAC */ -static struct stmmac_mdio_bus_data ls1x_mdio_bus_data = { - .phy_mask =0 , -}; - -static struct stmmac_dma_cfg ls1x_eth_dma_cfg = { - .pbl =1 , -}; - -int ls1x_eth_mux_init (struct platform_device *pdev,void *priv) -{ -struct plat_stmmacenet_data *plat_dat =NULL ; -u32 val; - - val =__raw_readl (LS1X_MUX_CTRL1 ); - -#if defined(CONFIG_LOONGSON1_LS1B ) - plat_dat =dev_get_platdata (&pdev->dev); -if (plat_dat->bus_id) { -__raw_writel (__raw_readl (LS1X_MUX_CTRL0 ) |GMAC1_USE_UART1 | -GMAC1_USE_UART0 ,LS1X_MUX_CTRL0 ); -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC1_SHUT ; - }else { -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC0_SHUT ; - } -__raw_writel (val,LS1X_MUX_CTRL1 ); -#elif defined(CONFIG_LOONGSON1_LS1C ) - plat_dat =dev_get_platdata (&pdev->dev); - - val &= ~PHY_INTF_SELI ; -if (plat_dat->phy_interface ==PHY_INTERFACE_MODE_RMII ) - val |=0x4 <<PHY_INTF_SELI_SHIFT ; -__raw_writel (val,LS1X_MUX_CTRL1 ); - - val =__raw_readl (LS1X_MUX_CTRL0 ); -__raw_writel (val & (~GMAC_SHUT ),LS1X_MUX_CTRL0 ); -#endif - -return 0 ; -} - -static struct plat_stmmacenet_data ls1x_eth0_pdata = { - .bus_id =0 , - .phy_addr =-1 , -#if defined(CONFIG_LOONGSON1_LS1B) - .phy_interface =PHY_INTERFACE_MODE_MII , -#elif defined(CONFIG_LOONGSON1_LS1C) - .phy_interface =PHY_INTERFACE_MODE_RMII , -#endif - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth0_resources[] = { - [0 ] = { - .start =LS1X_GMAC0_BASE , - .end =LS1X_GMAC0_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC0_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth0_pdev = { - .name ="stmmaceth" , - .id =0 , - .num_resources =ARRAY_SIZE (ls1x_eth0_resources), - .resource = ls1x_eth0_resources, - .dev = { - .platform_data = &ls1x_eth0_pdata, - }, -}; - -#ifdef CONFIG_LOONGSON1_LS1B -static struct plat_stmmacenet_data ls1x_eth1_pdata = { - .bus_id =1 , - .phy_addr =-1 , - .phy_interface =PHY_INTERFACE_MODE_MII , - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth1_resources[] = { - [0 ] = { - .start =LS1X_GMAC1_BASE , - .end =LS1X_GMAC1_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC1_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth1_pdev = { - .name ="stmmaceth" , - .id =1 , - .num_resources =ARRAY_SIZE (ls1x_eth1_resources), - .resource = ls1x_eth1_resources, - .dev = { - .platform_data = &ls1x_eth1_pdata, - }, -}; -#endif /* CONFIG_LOONGSON1_LS1B */ +#include <irq.h> /* GPIO */ static struct resource ls1x_gpio0_resources[] = {arch/mips/loongson32/ls1b/board.c +0
-2@@ -34,8 +34,6 @@ static const struct gpio_led_platform_data ls1x_led_pdata __initconst = { };static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_eth0_pdev, - &ls1x_eth1_pdev, &ls1x_ehci_pdev, &ls1x_gpio0_pdev, &ls1x_gpio1_pdev,arch/mips/loongson32/ls1c/board.c +0
-1@@ -6,7 +6,6 @@#include <platform.h> static struct platform_device *ls1c_platform_devices[]__initdata = { - &ls1x_eth0_pdev, &ls1x_rtc_pdev, &ls1x_wdt_pdev, };Signature · 1 line
2.39.2
Keguang Zhang
maintainerRe: [PATCH 08/17] MIPS: loongson32: Convert Ethernet platform device to DT
Quoted 5 lines · Serge Semin
Quoted 2 lines · Keguang Zhang
Add Ethernet device nodes for Loongson-1 boards, and drop the legacy platform devices and data accordingly.
Quoted 9 lines
It seems to me that your conversion breaks the RGMII mode support. What you need to do is to make sure that the respective flags are set in the MUX space.
Regarding the MUX-space. It looks as a pinctrl-setting space. If so adding the new pinctrl driver will be required. Otherwise it can be defined as a syscon-node and then utilized in the Loongson-1 GMAC low-level driver.
Thanks for your reminder.
I planned to add the pinctrl driver later.
Now I'm working on it.
Quoted 366 lines
-Serge(y)
Quoted 364 lines
Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 16 ++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 53 +++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 17 ++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 8 + arch/mips/boot/dts/loongson/smartloong_1c.dts | 4 + arch/mips/loongson32/common/platform.c | 146 +----------------- arch/mips/loongson32/ls1b/board.c | 2 - arch/mips/loongson32/ls1c/board.c | 1 - 8 files changed, 99 insertions(+), 148 deletions(-)arch/mips/boot/dts/loongson/loongson1.dtsi +16
-0@@ -71,6 +71,22 @@ intc3: interrupt-controller@1fd01088 { interrupt-parent = <&cpu_intc>; interrupts = <5>; }; + + gmac0: ethernet@1fe10000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe10000 0x10000>; + + interrupt-parent = <&intc1>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + snps,pbl = <1>; + + status = "disabled"; + }; + }; apb: bus@1fe40000 {arch/mips/boot/dts/loongson/loongson1b.dtsi +53
-0@@ -7,6 +7,11 @@ #include "loongson1.dtsi" / { + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + }; + cpus { #address-cells = <1>; #size-cells = <0>;@@ -74,6 +79,54 @@ clkc: clock-controller@1fe78030 { }; }; +&ahb { + gmac1: ethernet@1fe20000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe20000 0x10000>; + + interrupt-parent = <&intc1>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + phy-handle = <&phy1>; + phy-mode = "mii"; + + snps,pbl = <1>; + + status = "disabled"; + + mdio1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy1: ethernet-phy@0 { + reg = <0x0>; + }; + }; + }; +}; + +&gmac0 { + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "mii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + }; +}; + &uart1 { interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/loongson1c.dtsi +17
-0@@ -41,6 +41,23 @@ intc4: interrupt-controller@1fd010a0 { }; }; +&gmac0 { + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "rmii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@13 { + reg = <0x13>; + }; + }; +}; + &uart1 { interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +8
-0@@ -28,6 +28,14 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + +&gmac1 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/boot/dts/loongson/smartloong_1c.dts +4
-0@@ -28,6 +28,10 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/loongson32/common/platform.c +1
-145@@ -8,157 +8,13 @@#include <linux/err.h> #include <linux/mtd/partitions.h> #include <linux/sizes.h> -#include <linux/phy.h> -#include <linux/stmmac.h> #include <linux/usb/ehci_pdriver.h> #include <platform.h> #include <loongson1.h> #include <dma.h> #include <nand.h> - -/* Synopsys Ethernet GMAC */ -static struct stmmac_mdio_bus_data ls1x_mdio_bus_data = { - .phy_mask =0 , -}; - -static struct stmmac_dma_cfg ls1x_eth_dma_cfg = { - .pbl =1 , -}; - -int ls1x_eth_mux_init (struct platform_device *pdev,void *priv) -{ -struct plat_stmmacenet_data *plat_dat =NULL ; -u32 val; - - val =__raw_readl (LS1X_MUX_CTRL1 ); - -#if defined(CONFIG_LOONGSON1_LS1B ) - plat_dat =dev_get_platdata (&pdev->dev); -if (plat_dat->bus_id) { -__raw_writel (__raw_readl (LS1X_MUX_CTRL0 ) |GMAC1_USE_UART1 | -GMAC1_USE_UART0 ,LS1X_MUX_CTRL0 ); -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC1_SHUT ; - }else { -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC0_SHUT ; - } -__raw_writel (val,LS1X_MUX_CTRL1 ); -#elif defined(CONFIG_LOONGSON1_LS1C ) - plat_dat =dev_get_platdata (&pdev->dev); - - val &= ~PHY_INTF_SELI ; -if (plat_dat->phy_interface ==PHY_INTERFACE_MODE_RMII ) - val |=0x4 <<PHY_INTF_SELI_SHIFT ; -__raw_writel (val,LS1X_MUX_CTRL1 ); - - val =__raw_readl (LS1X_MUX_CTRL0 ); -__raw_writel (val & (~GMAC_SHUT ),LS1X_MUX_CTRL0 ); -#endif - -return 0 ; -} - -static struct plat_stmmacenet_data ls1x_eth0_pdata = { - .bus_id =0 , - .phy_addr =-1 , -#if defined(CONFIG_LOONGSON1_LS1B) - .phy_interface =PHY_INTERFACE_MODE_MII , -#elif defined(CONFIG_LOONGSON1_LS1C) - .phy_interface =PHY_INTERFACE_MODE_RMII , -#endif - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth0_resources[] = { - [0 ] = { - .start =LS1X_GMAC0_BASE , - .end =LS1X_GMAC0_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC0_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth0_pdev = { - .name ="stmmaceth" , - .id =0 , - .num_resources =ARRAY_SIZE (ls1x_eth0_resources), - .resource = ls1x_eth0_resources, - .dev = { - .platform_data = &ls1x_eth0_pdata, - }, -}; - -#ifdef CONFIG_LOONGSON1_LS1B -static struct plat_stmmacenet_data ls1x_eth1_pdata = { - .bus_id =1 , - .phy_addr =-1 , - .phy_interface =PHY_INTERFACE_MODE_MII , - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth1_resources[] = { - [0 ] = { - .start =LS1X_GMAC1_BASE , - .end =LS1X_GMAC1_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC1_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth1_pdev = { - .name ="stmmaceth" , - .id =1 , - .num_resources =ARRAY_SIZE (ls1x_eth1_resources), - .resource = ls1x_eth1_resources, - .dev = { - .platform_data = &ls1x_eth1_pdata, - }, -}; -#endif /* CONFIG_LOONGSON1_LS1B */ +#include <irq.h> /* GPIO */ static struct resource ls1x_gpio0_resources[] = {arch/mips/loongson32/ls1b/board.c +0
-2@@ -34,8 +34,6 @@ static const struct gpio_led_platform_data ls1x_led_pdata __initconst = { };static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_eth0_pdev, - &ls1x_eth1_pdev, &ls1x_ehci_pdev, &ls1x_gpio0_pdev, &ls1x_gpio1_pdev,arch/mips/loongson32/ls1c/board.c +0
-2@@ -6,7 +6,6 @@#include <platform.h> static struct platform_device *ls1c_platform_devices[]__initdata = { - &ls1x_eth0_pdev, &ls1x_rtc_pdev, &ls1x_wdt_pdev, }; --2.39.2
Signature · 3 lines
Best regards, Keguang Zhang
Re: [PATCH 08/17] MIPS: loongson32: Convert Ethernet platform device to DT
Quoted 16 lines · Keguang Zhang
Quoted 5 lines · Serge Semin
Quoted 2 lines · Keguang Zhang
Add Ethernet device nodes for Loongson-1 boards, and drop the legacy platform devices and data accordingly.
Quoted 9 lines
It seems to me that your conversion breaks the RGMII mode support. What you need to do is to make sure that the respective flags are set in the MUX space.
Regarding the MUX-space. It looks as a pinctrl-setting space. If so adding the new pinctrl driver will be required. Otherwise it can be defined as a syscon-node and then utilized in the Loongson-1 GMAC low-level driver.
Quoted 3 lines
Thanks for your reminder.
I planned to add the pinctrl driver later.
Now I'm working on it.
I have been having a patch moving the Loongson32 MAC driver to the STMMAC driver directory for quite a while in my tree. You can use it in your series (completely, as a reference or template, whatever). The only thing you'll need to do is to add the pinctrl-based version of the ls1b_eth_mux_init()/ls1c_eth_mux_init() methods in there and test/debug it of course.
Note 1. It seems to me that it would work better if you defined the plat_stmmacenet_data.fix_mac_speed() callback instead of plat_stmmacenet_data.init() for LS1B which supports MII and RGMII aka 100Mbps and 1000Mbps speeds.
Note 2. The patch I've sent was only built-tested. I don't have any Loongson hardware.
Note 3. After the suggested patch is applied you can also completely move the include/linux/stmmac.h header file to the STMMAC-driver directory as a following up cleanup update (it should be renamed to stmmac_platform.h since stmmac.h is already available in there). It can be done since there won't any users of that file outside the STMMAC-driver directory. So there is no point in keeping it in the common headers directory anymore.
-Serge(y)
Quoted 359 lines
Quoted 359 lines
-Serge(y)
Quoted 356 lines
Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 16 ++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 53 +++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 17 ++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 8 + arch/mips/boot/dts/loongson/smartloong_1c.dts | 4 + arch/mips/loongson32/common/platform.c | 146 +----------------- arch/mips/loongson32/ls1b/board.c | 2 - arch/mips/loongson32/ls1c/board.c | 1 - 8 files changed, 99 insertions(+), 148 deletions(-)arch/mips/boot/dts/loongson/loongson1.dtsi +16
-0@@ -71,6 +71,22 @@ intc3: interrupt-controller@1fd01088 { interrupt-parent = <&cpu_intc>; interrupts = <5>; }; + + gmac0: ethernet@1fe10000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe10000 0x10000>; + + interrupt-parent = <&intc1>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + snps,pbl = <1>; + + status = "disabled"; + }; + }; apb: bus@1fe40000 {arch/mips/boot/dts/loongson/loongson1b.dtsi +53
-0@@ -7,6 +7,11 @@ #include "loongson1.dtsi" / { + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + }; + cpus { #address-cells = <1>; #size-cells = <0>;@@ -74,6 +79,54 @@ clkc: clock-controller@1fe78030 { }; }; +&ahb { + gmac1: ethernet@1fe20000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe20000 0x10000>; + + interrupt-parent = <&intc1>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + phy-handle = <&phy1>; + phy-mode = "mii"; + + snps,pbl = <1>; + + status = "disabled"; + + mdio1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy1: ethernet-phy@0 { + reg = <0x0>; + }; + }; + }; +}; + +&gmac0 { + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "mii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + }; +}; + &uart1 { interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/loongson1c.dtsi +17
-0@@ -41,6 +41,23 @@ intc4: interrupt-controller@1fd010a0 { }; }; +&gmac0 { + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "rmii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@13 { + reg = <0x13>; + }; + }; +}; + &uart1 { interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +8
-0@@ -28,6 +28,14 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + +&gmac1 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/boot/dts/loongson/smartloong_1c.dts +4
-0@@ -28,6 +28,10 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/loongson32/common/platform.c +1
-145@@ -8,157 +8,13 @@#include <linux/err.h> #include <linux/mtd/partitions.h> #include <linux/sizes.h> -#include <linux/phy.h> -#include <linux/stmmac.h> #include <linux/usb/ehci_pdriver.h> #include <platform.h> #include <loongson1.h> #include <dma.h> #include <nand.h> - -/* Synopsys Ethernet GMAC */ -static struct stmmac_mdio_bus_data ls1x_mdio_bus_data = { - .phy_mask =0 , -}; - -static struct stmmac_dma_cfg ls1x_eth_dma_cfg = { - .pbl =1 , -}; - -int ls1x_eth_mux_init (struct platform_device *pdev,void *priv) -{ -struct plat_stmmacenet_data *plat_dat =NULL ; -u32 val; - - val =__raw_readl (LS1X_MUX_CTRL1 ); - -#if defined(CONFIG_LOONGSON1_LS1B ) - plat_dat =dev_get_platdata (&pdev->dev); -if (plat_dat->bus_id) { -__raw_writel (__raw_readl (LS1X_MUX_CTRL0 ) |GMAC1_USE_UART1 | -GMAC1_USE_UART0 ,LS1X_MUX_CTRL0 ); -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC1_SHUT ; - }else { -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC0_SHUT ; - } -__raw_writel (val,LS1X_MUX_CTRL1 ); -#elif defined(CONFIG_LOONGSON1_LS1C ) - plat_dat =dev_get_platdata (&pdev->dev); - - val &= ~PHY_INTF_SELI ; -if (plat_dat->phy_interface ==PHY_INTERFACE_MODE_RMII ) - val |=0x4 <<PHY_INTF_SELI_SHIFT ; -__raw_writel (val,LS1X_MUX_CTRL1 ); - - val =__raw_readl (LS1X_MUX_CTRL0 ); -__raw_writel (val & (~GMAC_SHUT ),LS1X_MUX_CTRL0 ); -#endif - -return 0 ; -} - -static struct plat_stmmacenet_data ls1x_eth0_pdata = { - .bus_id =0 , - .phy_addr =-1 , -#if defined(CONFIG_LOONGSON1_LS1B) - .phy_interface =PHY_INTERFACE_MODE_MII , -#elif defined(CONFIG_LOONGSON1_LS1C) - .phy_interface =PHY_INTERFACE_MODE_RMII , -#endif - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth0_resources[] = { - [0 ] = { - .start =LS1X_GMAC0_BASE , - .end =LS1X_GMAC0_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC0_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth0_pdev = { - .name ="stmmaceth" , - .id =0 , - .num_resources =ARRAY_SIZE (ls1x_eth0_resources), - .resource = ls1x_eth0_resources, - .dev = { - .platform_data = &ls1x_eth0_pdata, - }, -}; - -#ifdef CONFIG_LOONGSON1_LS1B -static struct plat_stmmacenet_data ls1x_eth1_pdata = { - .bus_id =1 , - .phy_addr =-1 , - .phy_interface =PHY_INTERFACE_MODE_MII , - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth1_resources[] = { - [0 ] = { - .start =LS1X_GMAC1_BASE , - .end =LS1X_GMAC1_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC1_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth1_pdev = { - .name ="stmmaceth" , - .id =1 , - .num_resources =ARRAY_SIZE (ls1x_eth1_resources), - .resource = ls1x_eth1_resources, - .dev = { - .platform_data = &ls1x_eth1_pdata, - }, -}; -#endif /* CONFIG_LOONGSON1_LS1B */ +#include <irq.h> /* GPIO */ static struct resource ls1x_gpio0_resources[] = {arch/mips/loongson32/ls1b/board.c +0
-2@@ -34,8 +34,6 @@ static const struct gpio_led_platform_data ls1x_led_pdata __initconst = { };static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_eth0_pdev, - &ls1x_eth1_pdev, &ls1x_ehci_pdev, &ls1x_gpio0_pdev, &ls1x_gpio1_pdev,arch/mips/loongson32/ls1c/board.c +0
-0@@ -6,7 +6,6 @@#include <platform.h>
Quoted 15 lines
Quoted 8 lines
Quoted 8 lines
arch/mips/loongson32/ls1c/board.c +0
-2static struct platform_device *ls1c_platform_devices[]__initdata = { - &ls1x_eth0_pdev, &ls1x_rtc_pdev, &ls1x_wdt_pdev, }; --2.39.2
Signature · 3 lines
Best regards, Keguang Zhang
From e63db52f7a2ac7288946a14f725c4547855f951f Mon Sep 17 00:00:00 2001
From: Serge Semin <[email protected]>
Date: Sun, 26 Sep 2021 23:41:51 +0300
Subject: [PATCH] net: stmmac: Move Loongson1 MAC arch-code to the driver dir
Loongson1 SoC is equipped with two GMAC interfaces based on the DW GMAC v3.x. Both of them are exposed on Loongson 1B boards, and just one of them
- on Loongson 1C boards. The glue driver has been created purely based on the arch-code implemented earlier with the platform-specific settings. That's why the sloppy mux-switching has been left as is until someone dares to create a driver for the embedded mux.
Note after this commit is merged in there won't be any platform_data-based code left using the STMMAC-platform interface. Thus the STMMAC platform_data declarations can be freely moved away from the generic kernel headers set into the driver directory.
---
Note I don't have a Loongson32 hardware at hand to test it out. I've built-test the change though. So should you have the hardware any tests and bug-reports would be very welcome.
--- MAINTAINERS | 1 + arch/mips/loongson32/common/platform.c | 111 +---------- drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 ++ drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + .../ethernet/stmicro/stmmac/dwmac-loongson1.c | 173 ++++++++++++++++++ 5 files changed, 193 insertions(+), 104 deletions(-) create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson1.c
MAINTAINERS +1 -0
@@ -14097,6 +14097,7 @@ L: [email protected] S: Maintained F: arch/mips/include/asm/mach-loongson32/ F: arch/mips/loongson32/ +F: drivers/*/*/*/*/*loongson1* F: drivers/*/*loongson1* MIPS/LOONGSON2EF ARCHITECTURE
arch/mips/loongson32/common/platform.c +7 -104
144 lines not on this page · raw message
drivers/net/ethernet/stmicro/stmmac/Kconfig +11 -0
@@ -263,6 +263,17 @@ config DWMAC_VISCONTI help Support for ethernet controller on Visconti SoCs. +config DWMAC_LOONGSON1 + tristate "Loongson1 GMAC support" + default LOONGSON1_LS1B || LOONGSON1_LS1C + depends on MACH_LOONGSON32 + help + Support for ethernet controller on Loongson1 SoC. + + This selects Loongson1 SoC glue layer support for the stmmac + device driver. This driver is used for Loongson1-based boards + like Loongson LS1B/LS1C. + endif config DWMAC_INTEL
drivers/net/ethernet/stmicro/stmmac/Makefile +1 -0
@@ -34,6 +34,7 @@ obj-$(CONFIG_DWMAC_GENERIC) += dwmac-generic.o obj-$(CONFIG_DWMAC_IMX8) += dwmac-imx.o obj-$(CONFIG_DWMAC_TEGRA) += dwmac-tegra.o obj-$(CONFIG_DWMAC_VISCONTI) += dwmac-visconti.o +obj-$(CONFIG_DWMAC_LOONGSON1) += dwmac-loongson1.o stmmac-platform-objs:= stmmac_platform.o dwmac-altr-socfpga-objs := altr_tse_pcs.o dwmac-socfpga.o
drivers/net/ethernet/stmicro/stmmac/dwmac-loongson1.c new file +172 -0
172 lines not on this page · raw message
Signature · 1 line
2.41.0
Keguang Zhang
maintainerRe: [PATCH 08/17] MIPS: loongson32: Convert Ethernet platform device to DT
Quoted 29 lines · Serge Semin
Quoted 16 lines · Keguang Zhang
Quoted 5 lines · Serge Semin
Quoted 2 lines · Keguang Zhang
Add Ethernet device nodes for Loongson-1 boards, and drop the legacy platform devices and data accordingly.
Quoted 9 lines
It seems to me that your conversion breaks the RGMII mode support. What you need to do is to make sure that the respective flags are set in the MUX space.
Regarding the MUX-space. It looks as a pinctrl-setting space. If so adding the new pinctrl driver will be required. Otherwise it can be defined as a syscon-node and then utilized in the Loongson-1 GMAC low-level driver.
Quoted 3 lines
Thanks for your reminder.
I planned to add the pinctrl driver later.
Now I'm working on it.I have been having a patch moving the Loongson32 MAC driver to the STMMAC driver directory for quite a while in my tree. You can use it in your series (completely, as a reference or template, whatever). The only thing you'll need to do is to add the pinctrl-based version of the ls1b_eth_mux_init()/ls1c_eth_mux_init() methods in there and test/debug it of course.
Quoted 5 lines
Note 1. It seems to me that it would work better if you defined the
plat_stmmacenet_data.fix_mac_speed()callback instead ofplat_stmmacenet_data.init()for LS1B which supports MII and RGMII aka 100Mbps and 1000Mbps speeds.
Thanks!
I will look into it.
However, I think ls1x_eth_mux_init() belongs to the scope of pinctrl or syscon. IMHO it is not worth implementing a glue driver for Loongson1.
Quoted 387 lines
Note 2. The patch I've sent was only built-tested. I don't have any Loongson hardware.
Note 3. After the suggested patch is applied you can also completely move the
include/linux/stmmac.hheader file to the STMMAC-driver directory as a following up cleanup update (it should be renamed tostmmac_platform.hsincestmmac.his already available in there). It can be done since there won't any users of that file outside the STMMAC-driver directory. So there is no point in keeping it in the common headers directory anymore.-Serge(y)
Quoted 374 lines
Quoted 359 lines
-Serge(y)
Quoted 356 lines
Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 16 ++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 53 +++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 17 ++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 8 + arch/mips/boot/dts/loongson/smartloong_1c.dts | 4 + arch/mips/loongson32/common/platform.c | 146 +----------------- arch/mips/loongson32/ls1b/board.c | 2 - arch/mips/loongson32/ls1c/board.c | 1 - 8 files changed, 99 insertions(+), 148 deletions(-)arch/mips/boot/dts/loongson/loongson1.dtsi +16
-0@@ -71,6 +71,22 @@ intc3: interrupt-controller@1fd01088 { interrupt-parent = <&cpu_intc>; interrupts = <5>; }; + + gmac0: ethernet@1fe10000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe10000 0x10000>; + + interrupt-parent = <&intc1>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + snps,pbl = <1>; + + status = "disabled"; + }; + }; apb: bus@1fe40000 {arch/mips/boot/dts/loongson/loongson1b.dtsi +53
-0@@ -7,6 +7,11 @@ #include "loongson1.dtsi" / { + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + }; + cpus { #address-cells = <1>; #size-cells = <0>;@@ -74,6 +79,54 @@ clkc: clock-controller@1fe78030 { }; }; +&ahb { + gmac1: ethernet@1fe20000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe20000 0x10000>; + + interrupt-parent = <&intc1>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + phy-handle = <&phy1>; + phy-mode = "mii"; + + snps,pbl = <1>; + + status = "disabled"; + + mdio1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy1: ethernet-phy@0 { + reg = <0x0>; + }; + }; + }; +}; + +&gmac0 { + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "mii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + }; +}; + &uart1 { interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/loongson1c.dtsi +17
-0@@ -41,6 +41,23 @@ intc4: interrupt-controller@1fd010a0 { }; }; +&gmac0 { + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "rmii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@13 { + reg = <0x13>; + }; + }; +}; + &uart1 { interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +8
-0@@ -28,6 +28,14 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + +&gmac1 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/boot/dts/loongson/smartloong_1c.dts +4
-0@@ -28,6 +28,10 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/loongson32/common/platform.c +1
-145@@ -8,157 +8,13 @@#include <linux/err.h> #include <linux/mtd/partitions.h> #include <linux/sizes.h> -#include <linux/phy.h> -#include <linux/stmmac.h> #include <linux/usb/ehci_pdriver.h> #include <platform.h> #include <loongson1.h> #include <dma.h> #include <nand.h> - -/* Synopsys Ethernet GMAC */ -static struct stmmac_mdio_bus_data ls1x_mdio_bus_data = { - .phy_mask =0 , -}; - -static struct stmmac_dma_cfg ls1x_eth_dma_cfg = { - .pbl =1 , -}; - -int ls1x_eth_mux_init (struct platform_device *pdev,void *priv) -{ -struct plat_stmmacenet_data *plat_dat =NULL ; -u32 val; - - val =__raw_readl (LS1X_MUX_CTRL1 ); - -#if defined(CONFIG_LOONGSON1_LS1B ) - plat_dat =dev_get_platdata (&pdev->dev); -if (plat_dat->bus_id) { -__raw_writel (__raw_readl (LS1X_MUX_CTRL0 ) |GMAC1_USE_UART1 | -GMAC1_USE_UART0 ,LS1X_MUX_CTRL0 ); -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC1_SHUT ; - }else { -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC0_SHUT ; - } -__raw_writel (val,LS1X_MUX_CTRL1 ); -#elif defined(CONFIG_LOONGSON1_LS1C ) - plat_dat =dev_get_platdata (&pdev->dev); - - val &= ~PHY_INTF_SELI ; -if (plat_dat->phy_interface ==PHY_INTERFACE_MODE_RMII ) - val |=0x4 <<PHY_INTF_SELI_SHIFT ; -__raw_writel (val,LS1X_MUX_CTRL1 ); - - val =__raw_readl (LS1X_MUX_CTRL0 ); -__raw_writel (val & (~GMAC_SHUT ),LS1X_MUX_CTRL0 ); -#endif - -return 0 ; -} - -static struct plat_stmmacenet_data ls1x_eth0_pdata = { - .bus_id =0 , - .phy_addr =-1 , -#if defined(CONFIG_LOONGSON1_LS1B) - .phy_interface =PHY_INTERFACE_MODE_MII , -#elif defined(CONFIG_LOONGSON1_LS1C) - .phy_interface =PHY_INTERFACE_MODE_RMII , -#endif - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth0_resources[] = { - [0 ] = { - .start =LS1X_GMAC0_BASE , - .end =LS1X_GMAC0_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC0_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth0_pdev = { - .name ="stmmaceth" , - .id =0 , - .num_resources =ARRAY_SIZE (ls1x_eth0_resources), - .resource = ls1x_eth0_resources, - .dev = { - .platform_data = &ls1x_eth0_pdata, - }, -}; - -#ifdef CONFIG_LOONGSON1_LS1B -static struct plat_stmmacenet_data ls1x_eth1_pdata = { - .bus_id =1 , - .phy_addr =-1 , - .phy_interface =PHY_INTERFACE_MODE_MII , - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth1_resources[] = { - [0 ] = { - .start =LS1X_GMAC1_BASE , - .end =LS1X_GMAC1_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC1_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth1_pdev = { - .name ="stmmaceth" , - .id =1 , - .num_resources =ARRAY_SIZE (ls1x_eth1_resources), - .resource = ls1x_eth1_resources, - .dev = { - .platform_data = &ls1x_eth1_pdata, - }, -}; -#endif /* CONFIG_LOONGSON1_LS1B */ +#include <irq.h> /* GPIO */ static struct resource ls1x_gpio0_resources[] = {arch/mips/loongson32/ls1b/board.c +0
-2@@ -34,8 +34,6 @@ static const struct gpio_led_platform_data ls1x_led_pdata __initconst = { };static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_eth0_pdev, - &ls1x_eth1_pdev, &ls1x_ehci_pdev, &ls1x_gpio0_pdev, &ls1x_gpio1_pdev,arch/mips/loongson32/ls1c/board.c +0
-0@@ -6,7 +6,6 @@#include <platform.h> Quoted 8 lines
Quoted 8 lines
arch/mips/loongson32/ls1c/board.c +0
-2static struct platform_device *ls1c_platform_devices[]__initdata = { - &ls1x_eth0_pdev, &ls1x_rtc_pdev, &ls1x_wdt_pdev, }; --2.39.2
--
Best regards,Keguang Zhang
Signature · 3 lines
Best regards, Keguang Zhang
Re: [PATCH 08/17] MIPS: loongson32: Convert Ethernet platform device to DT
Quoted 36 lines · Keguang Zhang
Quoted 29 lines · Serge Semin
Quoted 16 lines · Keguang Zhang
Quoted 5 lines · Serge Semin
Quoted 2 lines · Keguang Zhang
Add Ethernet device nodes for Loongson-1 boards, and drop the legacy platform devices and data accordingly.
Quoted 9 lines
It seems to me that your conversion breaks the RGMII mode support. What you need to do is to make sure that the respective flags are set in the MUX space.
Regarding the MUX-space. It looks as a pinctrl-setting space. If so adding the new pinctrl driver will be required. Otherwise it can be defined as a syscon-node and then utilized in the Loongson-1 GMAC low-level driver.
Quoted 3 lines
Thanks for your reminder.
I planned to add the pinctrl driver later.
Now I'm working on it.I have been having a patch moving the Loongson32 MAC driver to the STMMAC driver directory for quite a while in my tree. You can use it in your series (completely, as a reference or template, whatever). The only thing you'll need to do is to add the pinctrl-based version of the ls1b_eth_mux_init()/ls1c_eth_mux_init() methods in there and test/debug it of course.
Quoted 5 lines
Note 1. It seems to me that it would work better if you defined the
plat_stmmacenet_data.fix_mac_speed()callback instead ofplat_stmmacenet_data.init()for LS1B which supports MII and RGMII aka 100Mbps and 1000Mbps speeds.
Quoted 3 lines
Thanks!
I will look into it.
However, I thinkls1x_eth_mux_init()belongs to the scope of pinctrl or syscon.
Partly yes and partly no. The pins-mode setup functionality needs to be implemented in pinctrl, but switching between RGMII and MII modes must be done in the GMAC driver (selecting between different pinctrl states).
Alternatively you can define the MUX1 and MUX2 registers as the syscon-regmap space, have it referenced in the Loongson32 MAC DT-node and then switch between the modes manually in a similar way as it done in the current MAC platform code or in my patch. But IMO implementing it by means of the pin-controller would be much better. Note it doesn't prevent you from directly accessing the MUX-registers from the drivers and using these registers as the regspace for a syscon-controller driver: see syscon_node_to_regmap() method.
Quoted 1 line
IMHO it is not worth implementing a glue driver for Loongson1.
Generic DW GMAC driver won't fully work for LS1B which requires the phy-mode (phy_interface) change. In order for that to work correctly it needs to be done in the framework of the fix_mac_speed() callback which is called on each interface open procedure. Note the network phylink semantic implies that the phy-mode may change in runtime between interface re-open cycle (for instance in order to be able to switch between different network PHY-s connected to the same MAC interface). That's why fix_mac_speed() is the best place for the PHY modes change, not the init() callback. Due to all of that you won't escape with just using a combination of the DT-properties.
-Serge(y)
Quoted 395 lines
Quoted 388 lines
Note 2. The patch I've sent was only built-tested. I don't have any Loongson hardware.
Note 3. After the suggested patch is applied you can also completely move the
include/linux/stmmac.hheader file to the STMMAC-driver directory as a following up cleanup update (it should be renamed tostmmac_platform.hsincestmmac.his already available in there). It can be done since there won't any users of that file outside the STMMAC-driver directory. So there is no point in keeping it in the common headers directory anymore.-Serge(y)
Quoted 374 lines
Quoted 359 lines
-Serge(y)
Quoted 356 lines
Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 16 ++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 53 +++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 17 ++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 8 + arch/mips/boot/dts/loongson/smartloong_1c.dts | 4 + arch/mips/loongson32/common/platform.c | 146 +----------------- arch/mips/loongson32/ls1b/board.c | 2 - arch/mips/loongson32/ls1c/board.c | 1 - 8 files changed, 99 insertions(+), 148 deletions(-)arch/mips/boot/dts/loongson/loongson1.dtsi +16
-0@@ -71,6 +71,22 @@ intc3: interrupt-controller@1fd01088 { interrupt-parent = <&cpu_intc>; interrupts = <5>; }; + + gmac0: ethernet@1fe10000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe10000 0x10000>; + + interrupt-parent = <&intc1>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + snps,pbl = <1>; + + status = "disabled"; + }; + }; apb: bus@1fe40000 {arch/mips/boot/dts/loongson/loongson1b.dtsi +53
-0@@ -7,6 +7,11 @@ #include "loongson1.dtsi" / { + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + }; + cpus { #address-cells = <1>; #size-cells = <0>;@@ -74,6 +79,54 @@ clkc: clock-controller@1fe78030 { }; }; +&ahb { + gmac1: ethernet@1fe20000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe20000 0x10000>; + + interrupt-parent = <&intc1>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + phy-handle = <&phy1>; + phy-mode = "mii"; + + snps,pbl = <1>; + + status = "disabled"; + + mdio1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy1: ethernet-phy@0 { + reg = <0x0>; + }; + }; + }; +}; + +&gmac0 { + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "mii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + }; +}; + &uart1 { interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/loongson1c.dtsi +17
-0@@ -41,6 +41,23 @@ intc4: interrupt-controller@1fd010a0 { }; }; +&gmac0 { + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "rmii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@13 { + reg = <0x13>; + }; + }; +}; + &uart1 { interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +8
-0@@ -28,6 +28,14 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + +&gmac1 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/boot/dts/loongson/smartloong_1c.dts +4
-0@@ -28,6 +28,10 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/loongson32/common/platform.c +1
-145@@ -8,157 +8,13 @@#include <linux/err.h> #include <linux/mtd/partitions.h> #include <linux/sizes.h> -#include <linux/phy.h> -#include <linux/stmmac.h> #include <linux/usb/ehci_pdriver.h> #include <platform.h> #include <loongson1.h> #include <dma.h> #include <nand.h> - -/* Synopsys Ethernet GMAC */ -static struct stmmac_mdio_bus_data ls1x_mdio_bus_data = { - .phy_mask =0 , -}; - -static struct stmmac_dma_cfg ls1x_eth_dma_cfg = { - .pbl =1 , -}; - -int ls1x_eth_mux_init (struct platform_device *pdev,void *priv) -{ -struct plat_stmmacenet_data *plat_dat =NULL ; -u32 val; - - val =__raw_readl (LS1X_MUX_CTRL1 ); - -#if defined(CONFIG_LOONGSON1_LS1B ) - plat_dat =dev_get_platdata (&pdev->dev); -if (plat_dat->bus_id) { -__raw_writel (__raw_readl (LS1X_MUX_CTRL0 ) |GMAC1_USE_UART1 | -GMAC1_USE_UART0 ,LS1X_MUX_CTRL0 ); -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC1_SHUT ; - }else { -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC0_SHUT ; - } -__raw_writel (val,LS1X_MUX_CTRL1 ); -#elif defined(CONFIG_LOONGSON1_LS1C ) - plat_dat =dev_get_platdata (&pdev->dev); - - val &= ~PHY_INTF_SELI ; -if (plat_dat->phy_interface ==PHY_INTERFACE_MODE_RMII ) - val |=0x4 <<PHY_INTF_SELI_SHIFT ; -__raw_writel (val,LS1X_MUX_CTRL1 ); - - val =__raw_readl (LS1X_MUX_CTRL0 ); -__raw_writel (val & (~GMAC_SHUT ),LS1X_MUX_CTRL0 ); -#endif - -return 0 ; -} - -static struct plat_stmmacenet_data ls1x_eth0_pdata = { - .bus_id =0 , - .phy_addr =-1 , -#if defined(CONFIG_LOONGSON1_LS1B) - .phy_interface =PHY_INTERFACE_MODE_MII , -#elif defined(CONFIG_LOONGSON1_LS1C) - .phy_interface =PHY_INTERFACE_MODE_RMII , -#endif - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth0_resources[] = { - [0 ] = { - .start =LS1X_GMAC0_BASE , - .end =LS1X_GMAC0_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC0_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth0_pdev = { - .name ="stmmaceth" , - .id =0 , - .num_resources =ARRAY_SIZE (ls1x_eth0_resources), - .resource = ls1x_eth0_resources, - .dev = { - .platform_data = &ls1x_eth0_pdata, - }, -}; - -#ifdef CONFIG_LOONGSON1_LS1B -static struct plat_stmmacenet_data ls1x_eth1_pdata = { - .bus_id =1 , - .phy_addr =-1 , - .phy_interface =PHY_INTERFACE_MODE_MII , - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth1_resources[] = { - [0 ] = { - .start =LS1X_GMAC1_BASE , - .end =LS1X_GMAC1_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC1_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth1_pdev = { - .name ="stmmaceth" , - .id =1 , - .num_resources =ARRAY_SIZE (ls1x_eth1_resources), - .resource = ls1x_eth1_resources, - .dev = { - .platform_data = &ls1x_eth1_pdata, - }, -}; -#endif /* CONFIG_LOONGSON1_LS1B */ +#include <irq.h> /* GPIO */ static struct resource ls1x_gpio0_resources[] = {arch/mips/loongson32/ls1b/board.c +0
-2@@ -34,8 +34,6 @@ static const struct gpio_led_platform_data ls1x_led_pdata __initconst = { };static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_eth0_pdev, - &ls1x_eth1_pdev, &ls1x_ehci_pdev, &ls1x_gpio0_pdev, &ls1x_gpio1_pdev,arch/mips/loongson32/ls1c/board.c +0
-0@@ -6,7 +6,6 @@#include <platform.h> Quoted 8 lines
Quoted 8 lines
arch/mips/loongson32/ls1c/board.c +0
-2static struct platform_device *ls1c_platform_devices[]__initdata = { - &ls1x_eth0_pdev, &ls1x_rtc_pdev, &ls1x_wdt_pdev, }; --2.39.2
--
Best regards,Keguang Zhang
Signature · 3 lines
Best regards, Keguang Zhang
Re: [PATCH 08/17] MIPS: loongson32: Convert Ethernet platform device to DT
In reply to Keguang ZhangQuoted 10 lines · Keguang Zhang
Quoted 9 lines · Serge Semin
Quoted 2 lines · Keguang Zhang
Add Ethernet device nodes for Loongson-1 boards, and drop the legacy platform devices and data accordingly.
It seems to me that your conversion breaks the RGMII mode support. What you need to do is to make sure that the respective flags are set in the MUX space.
Quoted 8 lines
Quoted 5 lines
Regarding the MUX-space. It looks as a pinctrl-setting space. If so adding the new pinctrl driver will be required. Otherwise it can be defined as a syscon-node and then utilized in the Loongson-1 GMAC low-level driver.
Thanks for your reminder.
I planned to add the pinctrl driver later.
Now I'm working on it.
hi, I wrote a tool(work-in-progress) for generating pinctrl driver, do you want to try, and avoid duplicate work.
and could you merge my ls1c300 devicetree for u-boot, because u-boot wants to keep the devicetree sync with the linux kernel. some nodes needed and working are not exist in your devicetree.
---
Du Huanpeng
Quoted 374 lines
Quoted 367 lines
-Serge(y)
Quoted 364 lines
Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 16 ++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 53 +++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 17 ++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 8 + arch/mips/boot/dts/loongson/smartloong_1c.dts | 4 + arch/mips/loongson32/common/platform.c | 146 +----------------- arch/mips/loongson32/ls1b/board.c | 2 - arch/mips/loongson32/ls1c/board.c | 1 - 8 files changed, 99 insertions(+), 148 deletions(-)arch/mips/boot/dts/loongson/loongson1.dtsi +16
-0@@ -71,6 +71,22 @@ intc3: interrupt-controller@1fd01088 { interrupt-parent = <&cpu_intc>; interrupts = <5>; }; + + gmac0: ethernet@1fe10000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe10000 0x10000>; + + interrupt-parent = <&intc1>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + snps,pbl = <1>; + + status = "disabled"; + }; + }; apb: bus@1fe40000 {arch/mips/boot/dts/loongson/loongson1b.dtsi +53
-0@@ -7,6 +7,11 @@ #include "loongson1.dtsi" / { + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + }; + cpus { #address-cells = <1>; #size-cells = <0>;@@ -74,6 +79,54 @@ clkc: clock-controller@1fe78030 { }; }; +&ahb { + gmac1: ethernet@1fe20000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe20000 0x10000>; + + interrupt-parent = <&intc1>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + phy-handle = <&phy1>; + phy-mode = "mii"; + + snps,pbl = <1>; + + status = "disabled"; + + mdio1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy1: ethernet-phy@0 { + reg = <0x0>; + }; + }; + }; +}; + +&gmac0 { + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "mii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + }; +}; + &uart1 { interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/loongson1c.dtsi +17
-0@@ -41,6 +41,23 @@ intc4: interrupt-controller@1fd010a0 { }; }; +&gmac0 { + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "rmii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@13 { + reg = <0x13>; + }; + }; +}; + &uart1 { interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +8
-0@@ -28,6 +28,14 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + +&gmac1 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/boot/dts/loongson/smartloong_1c.dts +4
-0@@ -28,6 +28,10 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/loongson32/common/platform.c +1
-145@@ -8,157 +8,13 @@#include <linux/err.h> #include <linux/mtd/partitions.h> #include <linux/sizes.h> -#include <linux/phy.h> -#include <linux/stmmac.h> #include <linux/usb/ehci_pdriver.h> #include <platform.h> #include <loongson1.h> #include <dma.h> #include <nand.h> - -/* Synopsys Ethernet GMAC */ -static struct stmmac_mdio_bus_data ls1x_mdio_bus_data = { - .phy_mask =0 , -}; - -static struct stmmac_dma_cfg ls1x_eth_dma_cfg = { - .pbl =1 , -}; - -int ls1x_eth_mux_init (struct platform_device *pdev,void *priv) -{ -struct plat_stmmacenet_data *plat_dat =NULL ; -u32 val; - - val =__raw_readl (LS1X_MUX_CTRL1 ); - -#if defined(CONFIG_LOONGSON1_LS1B ) - plat_dat =dev_get_platdata (&pdev->dev); -if (plat_dat->bus_id) { -__raw_writel (__raw_readl (LS1X_MUX_CTRL0 ) |GMAC1_USE_UART1 | -GMAC1_USE_UART0 ,LS1X_MUX_CTRL0 ); -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC1_SHUT ; - }else { -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC0_SHUT ; - } -__raw_writel (val,LS1X_MUX_CTRL1 ); -#elif defined(CONFIG_LOONGSON1_LS1C ) - plat_dat =dev_get_platdata (&pdev->dev); - - val &= ~PHY_INTF_SELI ; -if (plat_dat->phy_interface ==PHY_INTERFACE_MODE_RMII ) - val |=0x4 <<PHY_INTF_SELI_SHIFT ; -__raw_writel (val,LS1X_MUX_CTRL1 ); - - val =__raw_readl (LS1X_MUX_CTRL0 ); -__raw_writel (val & (~GMAC_SHUT ),LS1X_MUX_CTRL0 ); -#endif - -return 0 ; -} - -static struct plat_stmmacenet_data ls1x_eth0_pdata = { - .bus_id =0 , - .phy_addr =-1 , -#if defined(CONFIG_LOONGSON1_LS1B) - .phy_interface =PHY_INTERFACE_MODE_MII , -#elif defined(CONFIG_LOONGSON1_LS1C) - .phy_interface =PHY_INTERFACE_MODE_RMII , -#endif - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth0_resources[] = { - [0 ] = { - .start =LS1X_GMAC0_BASE , - .end =LS1X_GMAC0_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC0_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth0_pdev = { - .name ="stmmaceth" , - .id =0 , - .num_resources =ARRAY_SIZE (ls1x_eth0_resources), - .resource = ls1x_eth0_resources, - .dev = { - .platform_data = &ls1x_eth0_pdata, - }, -}; - -#ifdef CONFIG_LOONGSON1_LS1B -static struct plat_stmmacenet_data ls1x_eth1_pdata = { - .bus_id =1 , - .phy_addr =-1 , - .phy_interface =PHY_INTERFACE_MODE_MII , - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth1_resources[] = { - [0 ] = { - .start =LS1X_GMAC1_BASE , - .end =LS1X_GMAC1_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC1_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth1_pdev = { - .name ="stmmaceth" , - .id =1 , - .num_resources =ARRAY_SIZE (ls1x_eth1_resources), - .resource = ls1x_eth1_resources, - .dev = { - .platform_data = &ls1x_eth1_pdata, - }, -}; -#endif /* CONFIG_LOONGSON1_LS1B */ +#include <irq.h> /* GPIO */ static struct resource ls1x_gpio0_resources[] = {arch/mips/loongson32/ls1b/board.c +0
-2@@ -34,8 +34,6 @@ static const struct gpio_led_platform_data ls1x_led_pdata __initconst = { };static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_eth0_pdev, - &ls1x_eth1_pdev, &ls1x_ehci_pdev, &ls1x_gpio0_pdev, &ls1x_gpio1_pdev,arch/mips/loongson32/ls1c/board.c +0
-2@@ -6,7 +6,6 @@#include <platform.h> static struct platform_device *ls1c_platform_devices[]__initdata = { - &ls1x_eth0_pdev, &ls1x_rtc_pdev, &ls1x_wdt_pdev, }; --2.39.2
Signature · 3 lines
Best regards, Keguang Zhang
Keguang Zhang
maintainerRe: [PATCH 08/17] MIPS: loongson32: Convert Ethernet platform device to DT
Quoted 17 lines · Du Huanpeng
Quoted 15 lines · Keguang Zhang
Quoted 14 lines · Serge Semin
Quoted 2 lines · Keguang Zhang
Add Ethernet device nodes for Loongson-1 boards, and drop the legacy platform devices and data accordingly.
It seems to me that your conversion breaks the RGMII mode support. What you need to do is to make sure that the respective flags are set in the MUX space.
Regarding the MUX-space. It looks as a pinctrl-setting space. If so adding the new pinctrl driver will be required. Otherwise it can be defined as a syscon-node and then utilized in the Loongson-1 GMAC low-level driver.
Quoted 5 lines
Quoted 3 lines
Thanks for your reminder.
I planned to add the pinctrl driver later.
Now I'm working on it.hi, I wrote a tool(work-in-progress) for generating pinctrl driver, do you want to try, and avoid duplicate work.
A tool for generating pinctrl driver?
Could you share it?
Perhaps you could submit your driver when it is done. Thanks!
Quoted 6 lines
and could you merge my ls1c300 devicetree for u-boot, because u-boot wants to keep the devicetree sync with the linux kernel. some nodes needed and working are not exist in your devicetree.
I 've noticed your eariier commit for U-Boot. We can discuss it in more detail.
Quoted 376 lines
---
Du HuanpengQuoted 374 lines
Quoted 359 lines
-Serge(y)
Quoted 356 lines
Signed-off-by Keguang Zhang <[email protected]>--- arch/mips/boot/dts/loongson/loongson1.dtsi | 16 ++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 53 +++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 17 ++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 8 + arch/mips/boot/dts/loongson/smartloong_1c.dts | 4 + arch/mips/loongson32/common/platform.c | 146 +----------------- arch/mips/loongson32/ls1b/board.c | 2 - arch/mips/loongson32/ls1c/board.c | 1 - 8 files changed, 99 insertions(+), 148 deletions(-)arch/mips/boot/dts/loongson/loongson1.dtsi +16
-0@@ -71,6 +71,22 @@ intc3: interrupt-controller@1fd01088 { interrupt-parent = <&cpu_intc>; interrupts = <5>; }; + + gmac0: ethernet@1fe10000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe10000 0x10000>; + + interrupt-parent = <&intc1>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + snps,pbl = <1>; + + status = "disabled"; + }; + }; apb: bus@1fe40000 {arch/mips/boot/dts/loongson/loongson1b.dtsi +53
-0@@ -7,6 +7,11 @@ #include "loongson1.dtsi" / { + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + }; + cpus { #address-cells = <1>; #size-cells = <0>;@@ -74,6 +79,54 @@ clkc: clock-controller@1fe78030 { }; }; +&ahb { + gmac1: ethernet@1fe20000 { + compatible = "snps,dwmac-3.70a"; + reg = <0x1fe20000 0x10000>; + + interrupt-parent = <&intc1>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + + clocks = <&clkc LS1X_CLKID_AHB>; + clock-names = "stmmaceth"; + + phy-handle = <&phy1>; + phy-mode = "mii"; + + snps,pbl = <1>; + + status = "disabled"; + + mdio1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy1: ethernet-phy@0 { + reg = <0x0>; + }; + }; + }; +}; + +&gmac0 { + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "mii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@0 { + reg = <0x0>; + }; + }; +}; + &uart1 { interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/loongson1c.dtsi +17
-0@@ -41,6 +41,23 @@ intc4: interrupt-controller@1fd010a0 { }; }; +&gmac0 { + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + + phy-handle = <&phy0>; + phy-mode = "rmii"; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@13 { + reg = <0x13>; + }; + }; +}; + &uart1 { interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; };arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +8
-0@@ -28,6 +28,14 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + +&gmac1 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/boot/dts/loongson/smartloong_1c.dts +4
-0@@ -28,6 +28,10 @@ xtal: xtal { }; }; +&gmac0 { + status = "okay"; +}; + &uart0 { status = "okay"; };arch/mips/loongson32/common/platform.c +1
-145@@ -8,157 +8,13 @@#include <linux/err.h> #include <linux/mtd/partitions.h> #include <linux/sizes.h> -#include <linux/phy.h> -#include <linux/stmmac.h> #include <linux/usb/ehci_pdriver.h> #include <platform.h> #include <loongson1.h> #include <dma.h> #include <nand.h> - -/* Synopsys Ethernet GMAC */ -static struct stmmac_mdio_bus_data ls1x_mdio_bus_data = { - .phy_mask =0 , -}; - -static struct stmmac_dma_cfg ls1x_eth_dma_cfg = { - .pbl =1 , -}; - -int ls1x_eth_mux_init (struct platform_device *pdev,void *priv) -{ -struct plat_stmmacenet_data *plat_dat =NULL ; -u32 val; - - val =__raw_readl (LS1X_MUX_CTRL1 ); - -#if defined(CONFIG_LOONGSON1_LS1B ) - plat_dat =dev_get_platdata (&pdev->dev); -if (plat_dat->bus_id) { -__raw_writel (__raw_readl (LS1X_MUX_CTRL0 ) |GMAC1_USE_UART1 | -GMAC1_USE_UART0 ,LS1X_MUX_CTRL0 ); -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC1_USE_TXCLK |GMAC1_USE_PWM23 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC1_SHUT ; - }else { -switch (plat_dat->phy_interface) { -case PHY_INTERFACE_MODE_RGMII : - val &= ~(GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -case PHY_INTERFACE_MODE_MII : - val |= (GMAC0_USE_TXCLK |GMAC0_USE_PWM01 ); -break ; -default : -pr_err ("unsupported mii mode %d\n" , - plat_dat->phy_interface); -return -ENOTSUPP ; - } - val &= ~GMAC0_SHUT ; - } -__raw_writel (val,LS1X_MUX_CTRL1 ); -#elif defined(CONFIG_LOONGSON1_LS1C ) - plat_dat =dev_get_platdata (&pdev->dev); - - val &= ~PHY_INTF_SELI ; -if (plat_dat->phy_interface ==PHY_INTERFACE_MODE_RMII ) - val |=0x4 <<PHY_INTF_SELI_SHIFT ; -__raw_writel (val,LS1X_MUX_CTRL1 ); - - val =__raw_readl (LS1X_MUX_CTRL0 ); -__raw_writel (val & (~GMAC_SHUT ),LS1X_MUX_CTRL0 ); -#endif - -return 0 ; -} - -static struct plat_stmmacenet_data ls1x_eth0_pdata = { - .bus_id =0 , - .phy_addr =-1 , -#if defined(CONFIG_LOONGSON1_LS1B) - .phy_interface =PHY_INTERFACE_MODE_MII , -#elif defined(CONFIG_LOONGSON1_LS1C) - .phy_interface =PHY_INTERFACE_MODE_RMII , -#endif - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth0_resources[] = { - [0 ] = { - .start =LS1X_GMAC0_BASE , - .end =LS1X_GMAC0_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC0_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth0_pdev = { - .name ="stmmaceth" , - .id =0 , - .num_resources =ARRAY_SIZE (ls1x_eth0_resources), - .resource = ls1x_eth0_resources, - .dev = { - .platform_data = &ls1x_eth0_pdata, - }, -}; - -#ifdef CONFIG_LOONGSON1_LS1B -static struct plat_stmmacenet_data ls1x_eth1_pdata = { - .bus_id =1 , - .phy_addr =-1 , - .phy_interface =PHY_INTERFACE_MODE_MII , - .mdio_bus_data = &ls1x_mdio_bus_data, - .dma_cfg = &ls1x_eth_dma_cfg, - .has_gmac =1 , - .tx_coe =1 , - .rx_queues_to_use =1 , - .tx_queues_to_use =1 , - .init = ls1x_eth_mux_init, -}; - -static struct resource ls1x_eth1_resources[] = { - [0 ] = { - .start =LS1X_GMAC1_BASE , - .end =LS1X_GMAC1_BASE +SZ_64K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .name ="macirq" , - .start =LS1X_GMAC1_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -struct platform_device ls1x_eth1_pdev = { - .name ="stmmaceth" , - .id =1 , - .num_resources =ARRAY_SIZE (ls1x_eth1_resources), - .resource = ls1x_eth1_resources, - .dev = { - .platform_data = &ls1x_eth1_pdata, - }, -}; -#endif /* CONFIG_LOONGSON1_LS1B */ +#include <irq.h> /* GPIO */ static struct resource ls1x_gpio0_resources[] = {arch/mips/loongson32/ls1b/board.c +0
-2@@ -34,8 +34,6 @@ static const struct gpio_led_platform_data ls1x_led_pdata __initconst = { };static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_eth0_pdev, - &ls1x_eth1_pdev, &ls1x_ehci_pdev, &ls1x_gpio0_pdev, &ls1x_gpio1_pdev,arch/mips/loongson32/ls1c/board.c +0
-0@@ -6,7 +6,6 @@#include <platform.h> Quoted 8 lines
Quoted 8 lines
arch/mips/loongson32/ls1c/board.c +0
-2static struct platform_device *ls1c_platform_devices[]__initdata = { - &ls1x_eth0_pdev, &ls1x_rtc_pdev, &ls1x_wdt_pdev, }; --2.39.2
--
Best regards,Keguang Zhang
Signature · 3 lines
Best regards, Keguang Zhang
Keguang Zhang
maintainerPATCH 9/17 MIPS: loongson32: Convert GPIO platform device to DT
In reply to Keguang ZhangAdd GPIO device nodes for Loongson-1 boards,
and drop the legacy platform devices and data accordingly.
--- arch/mips/boot/dts/loongson/loongson1.dtsi | 16 ++++++++++ arch/mips/boot/dts/loongson/loongson1b.dtsi | 10 ++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 35 +++++++++++++++++++++ arch/mips/loongson32/common/platform.c | 31 ------------------ arch/mips/loongson32/ls1b/board.c | 2 -- 5 files changed, 61 insertions(+), 33 deletions(-)
arch/mips/boot/dts/loongson/loongson1.dtsi +16 -0
@@ -72,6 +72,22 @@ intc3: interrupt-controller@1fd01088 { interrupts = <5>; }; + gpio0: gpio@1fd010c0 { + compatible = "loongson,ls1x-gpio"; + reg = <0x1fd010c0 0x4>; + + gpio-controller; + #gpio-cells = <2>; + }; + + gpio1: gpio@1fd010c4 { + compatible = "loongson,ls1x-gpio"; + reg = <0x1fd010c4 0x4>; + + gpio-controller; + #gpio-cells = <2>; + }; + gmac0: ethernet@1fe10000 { compatible = "snps,dwmac-3.70a"; reg = <0x1fe10000 0x10000>;
arch/mips/boot/dts/loongson/loongson1b.dtsi +10 -0
@@ -10,6 +10,8 @@ / { aliases { ethernet0 = &gmac0; ethernet1 = &gmac1; + gpio0 = &gpio0; + gpio1 = &gpio1; }; cpus {
@@ -110,6 +112,14 @@ phy1: ethernet-phy@0 { }; }; +&gpio0 { + ngpios = <31>; +}; + +&gpio1 { + ngpios = <30>; +}; + &gmac0 { interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
arch/mips/boot/dts/loongson/loongson1c.dtsi +35 -0
@@ -7,6 +7,13 @@ #include "loongson1.dtsi" / { + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + }; + cpus { #address-cells = <1>; #size-cells = <0>;
@@ -39,6 +46,34 @@ intc4: interrupt-controller@1fd010a0 { interrupt-parent = <&cpu_intc>; interrupts = <6>; }; + + gpio2: gpio@1fd010c8 { + compatible = "loongson,ls1x-gpio"; + reg = <0x1fd010c8 0x4>; + + gpio-controller; + #gpio-cells = <2>; + + ngpios = <32>; + }; + + gpio3: gpio@1fd010cc { + compatible = "loongson,ls1x-gpio"; + reg = <0x1fd010cc 0x4>; + + gpio-controller; + #gpio-cells = <2>; + + ngpios = <32>; + }; +}; + +&gpio0 { + ngpios = <32>; +}; + +&gpio1 { + ngpios = <32>; }; &gmac0 {
arch/mips/loongson32/common/platform.c +0 -31
@@ -16,37 +16,6 @@#include <nand.h> #include <irq.h> -/* GPIO */ -static struct resource ls1x_gpio0_resources[] = { - [0 ] = { - .start =LS1X_GPIO0_BASE , - .end =LS1X_GPIO0_BASE +SZ_4 -1 , - .flags =IORESOURCE_MEM , - }, -}; - -struct platform_device ls1x_gpio0_pdev = { - .name ="ls1x-gpio" , - .id =0 , - .num_resources =ARRAY_SIZE (ls1x_gpio0_resources), - .resource = ls1x_gpio0_resources, -}; - -static struct resource ls1x_gpio1_resources[] = { - [0 ] = { - .start =LS1X_GPIO1_BASE , - .end =LS1X_GPIO1_BASE +SZ_4 -1 , - .flags =IORESOURCE_MEM , - }, -}; - -struct platform_device ls1x_gpio1_pdev = { - .name ="ls1x-gpio" , - .id =1 , - .num_resources =ARRAY_SIZE (ls1x_gpio1_resources), - .resource = ls1x_gpio1_resources, -}; -/* USB EHCI */ static u64 ls1x_ehci_dmamask =DMA_BIT_MASK (32 );
arch/mips/loongson32/ls1b/board.c +0 -2
@@ -35,8 +35,6 @@ static const struct gpio_led_platform_data ls1x_led_pdata __initconst = {static struct platform_device *ls1b_platform_devices[]__initdata = { &ls1x_ehci_pdev, - &ls1x_gpio0_pdev, - &ls1x_gpio1_pdev, &ls1x_rtc_pdev, &ls1x_wdt_pdev, };
Signature · 1 line
2.39.2
Keguang Zhang
maintainerPATCH 10/17 MIPS: loongson32: Convert GPIO LED platform device to DT
In reply to Keguang ZhangAdd GPIO LED device nodes for Loongson-1 boards, and drop the legacy platform devices and data accordingly.
--- arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 19 +++++++++++++++ arch/mips/boot/dts/loongson/smartloong_1c.dts | 19 +++++++++++++++ arch/mips/loongson32/ls1b/board.c | 23 ------------------- 3 files changed, 38 insertions(+), 23 deletions(-)
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +19 -0
@@ -5,6 +5,8 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> + #include "loongson1b.dtsi" / {
@@ -26,6 +28,23 @@ xtal: xtal { clock-output-names = "xtal"; #clock-cells = <0>; }; + + leds { + compatible = "gpio-leds"; + + led9 { + label = "led9"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + + led6 { + label = "led6"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + linux,default-trigger = "nand-disk"; + }; + + }; }; &gmac0 {
arch/mips/boot/dts/loongson/smartloong_1c.dts +19 -0
@@ -5,6 +5,8 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> + #include "loongson1c.dtsi" / {
@@ -26,6 +28,23 @@ xtal: xtal { clock-output-names = "xtal"; #clock-cells = <0>; }; + + leds { + compatible = "gpio-leds"; + + led0 { + label = "led0"; + gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + + led1 { + label = "led1"; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; + linux,default-trigger = "nand-disk"; + }; + + }; }; &gmac0 {
arch/mips/loongson32/ls1b/board.c +0 -23
@@ -12,27 +12,6 @@#include <nand.h> #include <platform.h> -static const struct gpio_led ls1x_gpio_leds[]__initconst = { - { - .name ="LED9" , - .default_trigger ="heartbeat" , - .gpio =38 , - .active_low =1 , - .default_state =LEDS_GPIO_DEFSTATE_OFF , - }, { - .name ="LED6" , - .default_trigger ="nand-disk" , - .gpio =39 , - .active_low =1 , - .default_state =LEDS_GPIO_DEFSTATE_OFF , - }, -}; - -static const struct gpio_led_platform_data ls1x_led_pdata__initconst = { - .num_leds =ARRAY_SIZE (ls1x_gpio_leds), - .leds = ls1x_gpio_leds, -}; -static struct platform_device *ls1b_platform_devices[]__initdata = { &ls1x_ehci_pdev, &ls1x_rtc_pdev,
@@ -41,8 +20,6 @@ static struct platform_device *ls1b_platform_devices[] __initdata = {static int __init ls1b_platform_init (void ) { -gpio_led_register_device (-1 , &ls1x_led_pdata); -return platform_add_devices (ls1b_platform_devices,ARRAY_SIZE (ls1b_platform_devices)); }
Signature · 1 line
2.39.2
Keguang Zhang
maintainerPATCH 11/17 MIPS: loongson32: Convert USB host platform device to DT
In reply to Keguang ZhangAdd USB host device nodes for Loongson-1 boards, and drop the legacy platform devices and data accordingly.
--- arch/mips/boot/dts/loongson/loongson1b.dtsi | 20 +++++++++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 20 +++++++++++++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 8 +++++ arch/mips/boot/dts/loongson/smartloong_1c.dts | 8 +++++ arch/mips/loongson32/common/platform.c | 29 ------------------- arch/mips/loongson32/ls1b/board.c | 1 - 6 files changed, 56 insertions(+), 30 deletions(-)
arch/mips/boot/dts/loongson/loongson1b.dtsi +20 -0
@@ -82,6 +82,26 @@ clkc: clock-controller@1fe78030 { }; &ahb { + ehci0: usb@1fe00000 { + compatible = "generic-ehci"; + reg = <0x1fe00000 0x100>; + + interrupt-parent = <&intc1>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + + status = "disabled"; + }; + + ohci0: usb@1fe08000 { + compatible = "generic-ohci"; + reg = <0x1fe08000 0x100>; + + interrupt-parent = <&intc1>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>; + + status = "disabled"; + }; + gmac1: ethernet@1fe20000 { compatible = "snps,dwmac-3.70a"; reg = <0x1fe20000 0x10000>;
arch/mips/boot/dts/loongson/loongson1c.dtsi +20 -0
@@ -66,6 +66,26 @@ gpio3: gpio@1fd010cc { ngpios = <32>; }; + + ehci0: usb@1fe20000 { + compatible = "generic-ehci"; + reg = <0x1fe20000 0x100>; + + interrupt-parent = <&intc1>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + + status = "disabled"; + }; + + ohci0: usb@1fe28000 { + compatible = "generic-ohci"; + reg = <0x1fe28000 0x100>; + + interrupt-parent = <&intc1>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>; + + status = "disabled"; + }; }; &gpio0 {
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +8 -0
@@ -55,6 +55,14 @@ &gmac1 { status = "okay"; }; +&ehci0 { + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + &uart0 { status = "okay"; };
arch/mips/boot/dts/loongson/smartloong_1c.dts +8 -0
@@ -51,6 +51,14 @@ &gmac0 { status = "okay"; }; +&ehci0 { + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + &uart0 { status = "okay"; };
arch/mips/loongson32/common/platform.c +0 -29
@@ -16,35 +16,6 @@#include <nand.h> #include <irq.h> -/* USB EHCI */ -static u64 ls1x_ehci_dmamask =DMA_BIT_MASK (32 ); - -static struct resource ls1x_ehci_resources[] = { - [0 ] = { - .start =LS1X_EHCI_BASE , - .end =LS1X_EHCI_BASE +SZ_32K -1 , - .flags =IORESOURCE_MEM , - }, - [1 ] = { - .start =LS1X_EHCI_IRQ , - .flags =IORESOURCE_IRQ , - }, -}; - -static struct usb_ehci_pdata ls1x_ehci_pdata = { -}; - -struct platform_device ls1x_ehci_pdev = { - .name ="ehci-platform" , - .id =-1 , - .num_resources =ARRAY_SIZE (ls1x_ehci_resources), - .resource = ls1x_ehci_resources, - .dev = { - .dma_mask = &ls1x_ehci_dmamask, - .platform_data = &ls1x_ehci_pdata, - }, -}; -/* Real Time Clock */ struct platform_device ls1x_rtc_pdev = { .name ="ls1x-rtc" ,
arch/mips/loongson32/ls1b/board.c +0 -1
@@ -13,7 +13,6 @@#include <platform.h> static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_ehci_pdev, &ls1x_rtc_pdev, &ls1x_wdt_pdev, };
Signature · 1 line
2.39.2
Keguang Zhang
maintainerPATCH 12/17 MIPS: loongson32: Convert RTC platform device to DT
In reply to Keguang ZhangAdd RTC device node for Loongson-1 boards,
and drop the legacy platform device and data accordingly.
--- arch/mips/boot/dts/loongson/loongson1b.dtsi | 12 ++++++++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 9 +++++++++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 4 ++++ arch/mips/boot/dts/loongson/smartloong_1c.dts | 4 ++++ arch/mips/loongson32/common/platform.c | 6 ------ arch/mips/loongson32/ls1b/board.c | 1 - arch/mips/loongson32/ls1c/board.c | 1 - 7 files changed, 29 insertions(+), 8 deletions(-)
arch/mips/boot/dts/loongson/loongson1b.dtsi +12 -0
@@ -132,6 +132,18 @@ phy1: ethernet-phy@0 { }; }; +&apb { + rtc: rtc@1fe64000 { + compatible = "loongson,ls1b-rtc"; + reg = <0x1fe64000 0x78>; + + interrupt-parent = <&intc0>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; + + status = "disabled"; + }; +}; + &gpio0 { ngpios = <31>; };
arch/mips/boot/dts/loongson/loongson1c.dtsi +9 -0
@@ -88,6 +88,15 @@ ohci0: usb@1fe28000 { }; }; +&apb { + rtc: rtc@1fe64000 { + compatible = "loongson,ls1c-rtc"; + reg = <0x1fe64000 0x78>; + + status = "disabled"; + }; +}; + &gpio0 { ngpios = <32>; };
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +4 -0
@@ -63,6 +63,10 @@ &ohci0 { status = "okay"; }; +&rtc { + status = "okay"; +}; + &uart0 { status = "okay"; };
arch/mips/boot/dts/loongson/smartloong_1c.dts +4 -0
@@ -59,6 +59,10 @@ &ohci0 { status = "okay"; }; +&rtc { + status = "okay"; +}; + &uart0 { status = "okay"; };
arch/mips/loongson32/common/platform.c +0 -6
@@ -16,12 +16,6 @@#include <nand.h> #include <irq.h> -/* Real Time Clock */ -struct platform_device ls1x_rtc_pdev = { - .name ="ls1x-rtc" , - .id =-1 , -}; -/* Watchdog */ static struct resource ls1x_wdt_resources[] = { {
arch/mips/loongson32/ls1b/board.c +0 -1
@@ -13,7 +13,6 @@#include <platform.h> static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_rtc_pdev, &ls1x_wdt_pdev, };
arch/mips/loongson32/ls1c/board.c +0 -1
@@ -6,7 +6,6 @@#include <platform.h> static struct platform_device *ls1c_platform_devices[]__initdata = { - &ls1x_rtc_pdev, &ls1x_wdt_pdev, };
Signature · 1 line
2.39.2
Keguang Zhang
maintainerPATCH 13/17 MIPS: loongson32: Convert watchdog platform device to DT
In reply to Keguang ZhangAdd watchdog device node for Loongson-1 boards, and drop the legacy platform device and data accordingly.
--- arch/mips/boot/dts/loongson/loongson1b.dtsi | 9 +++++++++ arch/mips/boot/dts/loongson/loongson1c.dtsi | 9 +++++++++ arch/mips/boot/dts/loongson/lsgz_1b_dev.dts | 4 ++++ arch/mips/boot/dts/loongson/smartloong_1c.dts | 4 ++++ arch/mips/loongson32/common/platform.c | 16 ---------------- arch/mips/loongson32/ls1b/board.c | 1 - arch/mips/loongson32/ls1c/board.c | 1 - 7 files changed, 26 insertions(+), 18 deletions(-)
arch/mips/boot/dts/loongson/loongson1b.dtsi +9 -0
@@ -133,6 +133,15 @@ phy1: ethernet-phy@0 { }; &apb { + watchdog: watchdog@1fe5c060 { + compatible = "loongson,ls1b-wdt"; + reg = <0x1fe5c060 0xc>; + + clocks = <&clkc LS1X_CLKID_APB>; + + status = "disabled"; + }; + rtc: rtc@1fe64000 { compatible = "loongson,ls1b-rtc"; reg = <0x1fe64000 0x78>;
arch/mips/boot/dts/loongson/loongson1c.dtsi +9 -0
@@ -89,6 +89,15 @@ ohci0: usb@1fe28000 { }; &apb { + watchdog: watchdog@1fe5c060 { + compatible = "loongson,ls1c-wdt"; + reg = <0x1fe5c060 0xc>; + + clocks = <&clkc LS1X_CLKID_APB>; + + status = "disabled"; + }; + rtc: rtc@1fe64000 { compatible = "loongson,ls1c-rtc"; reg = <0x1fe64000 0x78>;
arch/mips/boot/dts/loongson/lsgz_1b_dev.dts +4 -0
@@ -82,3 +82,7 @@ &uart2 { &uart3 { status = "okay"; }; + +&watchdog { + status = "okay"; +};
arch/mips/boot/dts/loongson/smartloong_1c.dts +4 -0
@@ -78,3 +78,7 @@ &uart2 { &uart3 { status = "okay"; }; + +&watchdog { + status = "okay"; +};
arch/mips/loongson32/common/platform.c +0 -16
@@ -15,19 +15,3 @@#include <dma.h> #include <nand.h> #include <irq.h> - -/* Watchdog */ -static struct resource ls1x_wdt_resources[] = { - { - .start =LS1X_WDT_BASE , - .end =LS1X_WDT_BASE +SZ_16 -1 , - .flags =IORESOURCE_MEM , - }, -}; - -struct platform_device ls1x_wdt_pdev = { - .name ="ls1x-wdt" , - .id =-1 , - .num_resources =ARRAY_SIZE (ls1x_wdt_resources), - .resource = ls1x_wdt_resources, -};
arch/mips/loongson32/ls1b/board.c +0 -1
@@ -13,7 +13,6 @@#include <platform.h> static struct platform_device *ls1b_platform_devices[]__initdata = { - &ls1x_wdt_pdev, };static int __init ls1b_platform_init (void )
arch/mips/loongson32/ls1c/board.c +0 -1
@@ -6,7 +6,6 @@#include <platform.h> static struct platform_device *ls1c_platform_devices[]__initdata = { - &ls1x_wdt_pdev, };static int __init ls1c_platform_init (void )
Signature · 1 line
2.39.2
Keguang Zhang
maintainerPATCH 14/17 mips: dts: loongson1b: Add PWM timer clocksource
In reply to Keguang ZhangAdd the device node of PWM timer clocksource
for Loongson-1B boards.
--- arch/mips/boot/dts/loongson/loongson1b.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/mips/boot/dts/loongson/loongson1b.dtsi +10 -0
@@ -79,6 +79,16 @@ clkc: clock-controller@1fe78030 { clocks = <&xtal>; #clock-cells = <1>; }; + + clocksource: timer@1fe5c030 { + compatible = "loongson,ls1b-pwmtimer"; + reg = <0x1fe5c030 0x10>; + + clocks = <&clkc LS1X_CLKID_APB>; + + interrupt-parent = <&intc0>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; + }; }; &ahb {
Signature · 1 line
2.39.2
Re: [PATCH 14/17] mips: dts: loongson1b: Add PWM timer clocksource
Quoted 2 lines · Keguang Zhang
Add the device node of PWM timer clocksource
for Loongson-1B boards.
Don't split adding new DTS into many small commits. There is little point in adding broken/incomplete DTS and immediately fix it. Just add complete one. We do the same for each drivers and DTS is not different here.
It would be entirely different if you followed 'release early, release often' approach, so release pieces as fast as you have them ready. You decided to ignore that rule, so no, you don't get 20 commits fixing DTS you added in first commit of the same patchset.
Best regards,
Krzysztof
Keguang Zhang
maintainerPATCH 15/17 MIPS: loongson32: Remove all the obsolete code of platform device
In reply to Keguang ZhangAll platform devices of Loongson-1 was converted to devicetree. Therefore, removes all the obsolete platform device related code, header files and Kconfig options.
--- arch/mips/include/asm/mach-loongson32/dma.h | 21 --- arch/mips/include/asm/mach-loongson32/irq.h | 107 --------------- .../include/asm/mach-loongson32/loongson1.h | 50 ------- arch/mips/include/asm/mach-loongson32/nand.h | 26 ---- .../include/asm/mach-loongson32/platform.h | 26 ---- .../include/asm/mach-loongson32/regs-mux.h | 124 ------------------ arch/mips/loongson32/Kconfig | 8 -- arch/mips/loongson32/Makefile | 13 -- arch/mips/loongson32/common/Makefile | 6 - arch/mips/loongson32/common/platform.c | 17 --- arch/mips/loongson32/ls1b/Makefile | 6 - arch/mips/loongson32/ls1b/board.c | 24 ---- arch/mips/loongson32/ls1c/Makefile | 6 - arch/mips/loongson32/ls1c/board.c | 17 --- 14 files changed, 451 deletions(-) delete mode 100644 arch/mips/include/asm/mach-loongson32/dma.h delete mode 100644 arch/mips/include/asm/mach-loongson32/irq.h delete mode 100644 arch/mips/include/asm/mach-loongson32/loongson1.h delete mode 100644 arch/mips/include/asm/mach-loongson32/nand.h delete mode 100644 arch/mips/include/asm/mach-loongson32/platform.h delete mode 100644 arch/mips/include/asm/mach-loongson32/regs-mux.h delete mode 100644 arch/mips/loongson32/common/Makefile delete mode 100644 arch/mips/loongson32/common/platform.c delete mode 100644 arch/mips/loongson32/ls1b/Makefile delete mode 100644 arch/mips/loongson32/ls1b/board.c delete mode 100644 arch/mips/loongson32/ls1c/Makefile delete mode 100644 arch/mips/loongson32/ls1c/board.c
arch/mips/include/asm/mach-loongson32/dma.h deleted +0 -21
@@ -1,21 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-or-later */ -/* -* Copyright (c) 2015 Zhang, Keguang <[email protected]> -* -* Loongson 1 NAND platform support. -*/ - -#ifndef __ASM_MACH_LOONGSON32_DMA_H -#define __ASM_MACH_LOONGSON32_DMA_H - -#define LS1X_DMA_CHANNEL0 0 -#define LS1X_DMA_CHANNEL1 1 -#define LS1X_DMA_CHANNEL2 2 - -struct plat_ls1x_dma { -int nr_channels; -}; - -extern struct plat_ls1x_dma ls1b_dma_pdata; - -#endif /* __ASM_MACH_LOONGSON32_DMA_H */
arch/mips/include/asm/mach-loongson32/irq.h deleted +0 -107
107 lines not on this page · raw message
arch/mips/include/asm/mach-loongson32/loongson1.h deleted +0 -50
50 lines not on this page · raw message
arch/mips/include/asm/mach-loongson32/nand.h deleted +0 -26
@@ -1,26 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-or-later */ -/* -* Copyright (c) 2015 Zhang, Keguang <[email protected]> -* -* Loongson 1 NAND platform support. -*/ - -#ifndef __ASM_MACH_LOONGSON32_NAND_H -#define __ASM_MACH_LOONGSON32_NAND_H - -#include <linux/dmaengine.h> -#include <linux/mtd/partitions.h> - -struct plat_ls1x_nand { -struct mtd_partition *parts; -unsigned int nr_parts; - -int hold_cycle; -int wait_cycle; -}; - -extern struct plat_ls1x_nand ls1b_nand_pdata; - -bool ls1x_dma_filter_fn (struct dma_chan *chan,void *param); - -#endif /* __ASM_MACH_LOONGSON32_NAND_H */
arch/mips/include/asm/mach-loongson32/platform.h deleted +0 -26
@@ -1,26 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-or-later */ -/* -* Copyright (c) 2011 Zhang, Keguang <[email protected]> -*/ - -#ifndef __ASM_MACH_LOONGSON32_PLATFORM_H -#define __ASM_MACH_LOONGSON32_PLATFORM_H - -#include <linux/platform_device.h> - -#include <dma.h> -#include <nand.h> - -extern struct platform_device ls1x_uart_pdev; -extern struct platform_device ls1x_eth0_pdev; -extern struct platform_device ls1x_eth1_pdev; -extern struct platform_device ls1x_ehci_pdev; -extern struct platform_device ls1x_gpio0_pdev; -extern struct platform_device ls1x_gpio1_pdev; -extern struct platform_device ls1x_rtc_pdev; -extern struct platform_device ls1x_wdt_pdev; - -void __init ls1x_rtc_set_extclk (struct platform_device *pdev); -void __init ls1x_serial_set_uartclk (struct platform_device *pdev); - -#endif /* __ASM_MACH_LOONGSON32_PLATFORM_H */
arch/mips/include/asm/mach-loongson32/regs-mux.h deleted +0 -124
124 lines not on this page · raw message
arch/mips/loongson32/Kconfig +0 -8
@@ -6,20 +6,12 @@ choice config MACH_LSGZ_1B_DEV bool "LSGZ 1B DEV board" - select LOONGSON1_LS1B help Enable this to include the FDT for the LSGZ 1B DEV board. config MACH_SMARTLOONG_1C bool "Smartloong 1C board" - select LOONGSON1_LS1C help Enable this to include the FDT for the Smartloong 1C board. endchoice - -config LOONGSON1_LS1B - bool - -config LOONGSON1_LS1C - bool
arch/mips/loongson32/Makefile +0 -13
@@ -4,16 +4,3 @@ # obj-$(CONFIG_MACH_LOONGSON32) += init.o proc.o -obj-$(CONFIG_MACH_LOONGSON32) += common/ - -# -# Loongson LS1B board -# - -obj-$(CONFIG_LOONGSON1_LS1B) += ls1b/ - -# -# Loongson LS1C board -# - -obj-$(CONFIG_LOONGSON1_LS1C) += ls1c/
arch/mips/loongson32/common/Makefile deleted +0 -6
@@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -# -# Makefile for common code of loongson1 based machines. -# - -obj-y += platform.o
arch/mips/loongson32/common/platform.c deleted +0 -17
@@ -1,17 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* -* Copyright (c) 2011-2016 Zhang, Keguang <[email protected]> -*/ - -#include <linux/clk.h> -#include <linux/dma-mapping.h> -#include <linux/err.h> -#include <linux/mtd/partitions.h> -#include <linux/sizes.h> -#include <linux/usb/ehci_pdriver.h> - -#include <platform.h> -#include <loongson1.h> -#include <dma.h> -#include <nand.h> -#include <irq.h>
arch/mips/loongson32/ls1b/Makefile deleted +0 -6
@@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -# -# Makefile for loongson1B based machines. -# - -obj-y += board.o
arch/mips/loongson32/ls1b/board.c deleted +0 -24
@@ -1,24 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* -* Copyright (c) 2011-2016 Zhang, Keguang <[email protected]> -*/ - -#include <linux/leds.h> -#include <linux/mtd/partitions.h> -#include <linux/sizes.h> - -#include <loongson1.h> -#include <dma.h> -#include <nand.h> -#include <platform.h> - -static struct platform_device *ls1b_platform_devices[]__initdata = { -}; - -static int __init ls1b_platform_init (void ) -{ -return platform_add_devices (ls1b_platform_devices, -ARRAY_SIZE (ls1b_platform_devices)); -} - -arch_initcall (ls1b_platform_init);
arch/mips/loongson32/ls1c/Makefile deleted +0 -6
@@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only -# -# Makefile for loongson1C based machines. -# - -obj-y += board.o
arch/mips/loongson32/ls1c/board.c deleted +0 -17
@@ -1,17 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* -* Copyright (c) 2016 Yang Ling <[email protected]> -*/ - -#include <platform.h> - -static struct platform_device *ls1c_platform_devices[]__initdata = { -}; - -static int __init ls1c_platform_init (void ) -{ -return platform_add_devices (ls1c_platform_devices, -ARRAY_SIZE (ls1c_platform_devices)); -} - -arch_initcall (ls1c_platform_init);
Signature · 1 line
2.39.2
Keguang Zhang
maintainerPATCH 16/17 MIPS: configs: Update and rename loongson1b_defconfig
In reply to Keguang ZhangRename the loongson1b_defconfig to the board name. Update the following options:
- Enable CONFIG_SERIAL_OF_PLATFORM
- Enable CONFIG_RTC_DRV_LOONGSON
- Enable CONFIG_CLKSRC_LOONGSON1_PWM
- Disable unnecessary options
---
...gson1b_defconfig => lsgz_1b_dev_defconfig} | 70 +++++++++++++++----
1 file changed, 55 insertions(+), 15 deletions(-)
rename arch/mips/configs/{loongson1b_defconfig => lsgz_1b_dev_defconfig} (59%)arch/mips/configs/lsgz_1b_dev_defconfig renamed from arch/mips/configs/loongson1b_defconfig +55 -15
@@ -1,7 +1,6 @@ # CONFIG_LOCALVERSION_AUTO is not set CONFIG_KERNEL_XZ=y CONFIG_SYSVIPC=y -CONFIG_HIGH_RES_TIMERS=y CONFIG_PREEMPT=y CONFIG_BSD_PROCESS_ACCT=y CONFIG_BSD_PROCESS_ACCT_V3=y
@@ -12,15 +11,16 @@ CONFIG_NAMESPACES=y CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_EXPERT=y CONFIG_PERF_EVENTS=y -# CONFIG_COMPAT_BRK is not set CONFIG_MACH_LOONGSON32=y -# CONFIG_SECCOMP is not set # CONFIG_SUSPEND is not set +# CONFIG_SECCOMP is not set +# CONFIG_GCC_PLUGINS is not set CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y CONFIG_MODVERSIONS=y -# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLOCK_LEGACY_AUTOLOAD is not set # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_COMPAT_BRK is not set CONFIG_NET=y CONFIG_PACKET=y CONFIG_UNIX=y
@@ -43,17 +43,50 @@ CONFIG_BLK_DEV_LOOP=y CONFIG_SCSI=m # CONFIG_SCSI_PROC_FS is not set CONFIG_BLK_DEV_SD=m +# CONFIG_BLK_DEV_BSG is not set # CONFIG_SCSI_LOWLEVEL is not set CONFIG_NETDEVICES=y +# CONFIG_NET_VENDOR_ALACRITECH is not set +# CONFIG_NET_VENDOR_AMAZON is not set +# CONFIG_NET_VENDOR_AQUANTIA is not set +# CONFIG_NET_VENDOR_ARC is not set +# CONFIG_NET_VENDOR_ASIX is not set # CONFIG_NET_VENDOR_BROADCOM is not set +# CONFIG_NET_VENDOR_CADENCE is not set +# CONFIG_NET_VENDOR_CAVIUM is not set +# CONFIG_NET_VENDOR_CORTINA is not set +# CONFIG_NET_VENDOR_DAVICOM is not set +# CONFIG_NET_VENDOR_ENGLEDER is not set +# CONFIG_NET_VENDOR_EZCHIP is not set +# CONFIG_NET_VENDOR_FUNGIBLE is not set +# CONFIG_NET_VENDOR_GOOGLE is not set +# CONFIG_NET_VENDOR_HUAWEI is not set # CONFIG_NET_VENDOR_INTEL is not set +# CONFIG_NET_VENDOR_LITEX is not set # CONFIG_NET_VENDOR_MARVELL is not set # CONFIG_NET_VENDOR_MICREL is not set +# CONFIG_NET_VENDOR_MICROCHIP is not set +# CONFIG_NET_VENDOR_MICROSEMI is not set +# CONFIG_NET_VENDOR_MICROSOFT is not set +# CONFIG_NET_VENDOR_NI is not set # CONFIG_NET_VENDOR_NATSEMI is not set +# CONFIG_NET_VENDOR_NETRONOME is not set +# CONFIG_NET_VENDOR_PENSANDO is not set +# CONFIG_NET_VENDOR_QUALCOMM is not set +# CONFIG_NET_VENDOR_RENESAS is not set +# CONFIG_NET_VENDOR_ROCKER is not set +# CONFIG_NET_VENDOR_SAMSUNG is not set # CONFIG_NET_VENDOR_SEEQ is not set +# CONFIG_NET_VENDOR_SOLARFLARE is not set # CONFIG_NET_VENDOR_SMSC is not set +# CONFIG_NET_VENDOR_SOCIONEXT is not set CONFIG_STMMAC_ETH=y +# CONFIG_NET_VENDOR_SYNOPSYS is not set +# CONFIG_NET_VENDOR_VERTEXCOM is not set +# CONFIG_NET_VENDOR_VIA is not set +# CONFIG_NET_VENDOR_WANGXUN is not set # CONFIG_NET_VENDOR_WIZNET is not set +# CONFIG_NET_VENDOR_XILINX is not set # CONFIG_WLAN is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_KEYBOARD is not set
@@ -63,7 +96,9 @@ CONFIG_VT_HW_CONSOLE_BINDING=y CONFIG_LEGACY_PTY_COUNT=8 CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_OF_PLATFORM=y # CONFIG_HW_RANDOM is not set +# CONFIG_PTP_1588_CLOCK is not set CONFIG_GPIOLIB=y CONFIG_GPIO_LOONGSON1=y # CONFIG_HWMON is not set
@@ -88,15 +123,15 @@ CONFIG_LEDS_GPIO=y CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_HEARTBEAT=y CONFIG_RTC_CLASS=y -CONFIG_RTC_DRV_LOONGSON1=y +CONFIG_RTC_DRV_LOONGSON=y +# CONFIG_VIRTIO_MENU is not set +# CONFIG_VHOST_MENU is not set +# CONFIG_MIPS_PLATFORM_DEVICES is not set +CONFIG_CLKSRC_LOONGSON1_PWM=y # CONFIG_IOMMU_SUPPORT is not set -CONFIG_EXT2_FS=y -CONFIG_EXT2_FS_XATTR=y -CONFIG_EXT2_FS_POSIX_ACL=y -CONFIG_EXT2_FS_SECURITY=y -CONFIG_EXT3_FS=y -CONFIG_EXT3_FS_POSIX_ACL=y -CONFIG_EXT3_FS_SECURITY=y +CONFIG_EXT4_FS=y +CONFIG_EXT4_FS_POSIX_ACL=y +CONFIG_EXT4_FS_SECURITY=y # CONFIG_DNOTIFY is not set CONFIG_VFAT_FS=y CONFIG_PROC_KCORE=y
@@ -109,12 +144,17 @@ CONFIG_NFS_FS=y CONFIG_ROOT_NFS=y CONFIG_NLS_CODEPAGE_437=m CONFIG_NLS_ISO8859_1=m -# CONFIG_CRYPTO_ECHAINIV is not set # CONFIG_CRYPTO_HW is not set +# CONFIG_XZ_DEC_X86 is not set +# CONFIG_XZ_DEC_POWERPC is not set +# CONFIG_XZ_DEC_IA64 is not set +# CONFIG_XZ_DEC_ARM is not set +# CONFIG_XZ_DEC_ARMTHUMB is not set +# CONFIG_XZ_DEC_SPARC is not set CONFIG_DYNAMIC_DEBUG=y -CONFIG_DEBUG_FS=y +# CONFIG_DEBUG_MISC is not set CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_FS=y # CONFIG_SCHED_DEBUG is not set -# CONFIG_DEBUG_PREEMPT is not set # CONFIG_FTRACE is not set # CONFIG_EARLY_PRINTK is not set
Signature · 1 line
2.39.2
Keguang Zhang
maintainerPATCH 17/17 MIPS: configs: Update and rename loongson1c_defconfig
In reply to Keguang ZhangRename the loongson1c_defconfig to the board name. Update the following options:
- Enable CONFIG_SERIAL_OF_PLATFORM
- Enable CONFIG_RTC_DRV_LOONGSON
- Disable unnecessary options
---
...on1c_defconfig => smartloong_1c_defconfig} | 71 ++++++++++++++-----
1 file changed, 55 insertions(+), 16 deletions(-)
rename arch/mips/configs/{loongson1c_defconfig => smartloong_1c_defconfig} (59%)arch/mips/configs/smartloong_1c_defconfig renamed from arch/mips/configs/loongson1c_defconfig +55 -16
@@ -1,7 +1,6 @@ # CONFIG_LOCALVERSION_AUTO is not set CONFIG_KERNEL_XZ=y CONFIG_SYSVIPC=y -CONFIG_HIGH_RES_TIMERS=y CONFIG_PREEMPT=y CONFIG_BSD_PROCESS_ACCT=y CONFIG_BSD_PROCESS_ACCT_V3=y
@@ -12,16 +11,17 @@ CONFIG_NAMESPACES=y CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_EXPERT=y CONFIG_PERF_EVENTS=y -# CONFIG_COMPAT_BRK is not set CONFIG_MACH_LOONGSON32=y -CONFIG_LOONGSON1_LS1C=y -# CONFIG_SECCOMP is not set +CONFIG_MACH_SMARTLOONG_1C=y # CONFIG_SUSPEND is not set +# CONFIG_SECCOMP is not set +# CONFIG_GCC_PLUGINS is not set CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y CONFIG_MODVERSIONS=y -# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLOCK_LEGACY_AUTOLOAD is not set # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_COMPAT_BRK is not set CONFIG_NET=y CONFIG_PACKET=y CONFIG_UNIX=y
@@ -44,17 +44,50 @@ CONFIG_BLK_DEV_LOOP=y CONFIG_SCSI=m # CONFIG_SCSI_PROC_FS is not set CONFIG_BLK_DEV_SD=m +# CONFIG_BLK_DEV_BSG is not set # CONFIG_SCSI_LOWLEVEL is not set CONFIG_NETDEVICES=y +# CONFIG_NET_VENDOR_ALACRITECH is not set +# CONFIG_NET_VENDOR_AMAZON is not set +# CONFIG_NET_VENDOR_AQUANTIA is not set +# CONFIG_NET_VENDOR_ARC is not set +# CONFIG_NET_VENDOR_ASIX is not set # CONFIG_NET_VENDOR_BROADCOM is not set +# CONFIG_NET_VENDOR_CADENCE is not set +# CONFIG_NET_VENDOR_CAVIUM is not set +# CONFIG_NET_VENDOR_CORTINA is not set +# CONFIG_NET_VENDOR_DAVICOM is not set +# CONFIG_NET_VENDOR_ENGLEDER is not set +# CONFIG_NET_VENDOR_EZCHIP is not set +# CONFIG_NET_VENDOR_FUNGIBLE is not set +# CONFIG_NET_VENDOR_GOOGLE is not set +# CONFIG_NET_VENDOR_HUAWEI is not set # CONFIG_NET_VENDOR_INTEL is not set +# CONFIG_NET_VENDOR_LITEX is not set # CONFIG_NET_VENDOR_MARVELL is not set # CONFIG_NET_VENDOR_MICREL is not set +# CONFIG_NET_VENDOR_MICROCHIP is not set +# CONFIG_NET_VENDOR_MICROSEMI is not set +# CONFIG_NET_VENDOR_MICROSOFT is not set +# CONFIG_NET_VENDOR_NI is not set # CONFIG_NET_VENDOR_NATSEMI is not set +# CONFIG_NET_VENDOR_NETRONOME is not set +# CONFIG_NET_VENDOR_PENSANDO is not set +# CONFIG_NET_VENDOR_QUALCOMM is not set +# CONFIG_NET_VENDOR_RENESAS is not set +# CONFIG_NET_VENDOR_ROCKER is not set +# CONFIG_NET_VENDOR_SAMSUNG is not set # CONFIG_NET_VENDOR_SEEQ is not set +# CONFIG_NET_VENDOR_SOLARFLARE is not set # CONFIG_NET_VENDOR_SMSC is not set +# CONFIG_NET_VENDOR_SOCIONEXT is not set CONFIG_STMMAC_ETH=y +# CONFIG_NET_VENDOR_SYNOPSYS is not set +# CONFIG_NET_VENDOR_VERTEXCOM is not set +# CONFIG_NET_VENDOR_VIA is not set +# CONFIG_NET_VENDOR_WANGXUN is not set # CONFIG_NET_VENDOR_WIZNET is not set +# CONFIG_NET_VENDOR_XILINX is not set # CONFIG_WLAN is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_KEYBOARD is not set
@@ -64,7 +97,9 @@ CONFIG_VT_HW_CONSOLE_BINDING=y CONFIG_LEGACY_PTY_COUNT=8 CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_OF_PLATFORM=y # CONFIG_HW_RANDOM is not set +# CONFIG_PTP_1588_CLOCK is not set CONFIG_GPIOLIB=y CONFIG_GPIO_LOONGSON1=y # CONFIG_HWMON is not set
@@ -89,15 +124,14 @@ CONFIG_LEDS_GPIO=y CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_HEARTBEAT=y CONFIG_RTC_CLASS=y -CONFIG_RTC_DRV_LOONGSON1=y +CONFIG_RTC_DRV_LOONGSON=y +# CONFIG_VIRTIO_MENU is not set +# CONFIG_VHOST_MENU is not set +# CONFIG_MIPS_PLATFORM_DEVICES is not set # CONFIG_IOMMU_SUPPORT is not set -CONFIG_EXT2_FS=y -CONFIG_EXT2_FS_XATTR=y -CONFIG_EXT2_FS_POSIX_ACL=y -CONFIG_EXT2_FS_SECURITY=y -CONFIG_EXT3_FS=y -CONFIG_EXT3_FS_POSIX_ACL=y -CONFIG_EXT3_FS_SECURITY=y +CONFIG_EXT4_FS=y +CONFIG_EXT4_FS_POSIX_ACL=y +CONFIG_EXT4_FS_SECURITY=y # CONFIG_DNOTIFY is not set CONFIG_VFAT_FS=y CONFIG_PROC_KCORE=y
@@ -110,12 +144,17 @@ CONFIG_NFS_FS=y CONFIG_ROOT_NFS=y CONFIG_NLS_CODEPAGE_437=m CONFIG_NLS_ISO8859_1=m -# CONFIG_CRYPTO_ECHAINIV is not set # CONFIG_CRYPTO_HW is not set +# CONFIG_XZ_DEC_X86 is not set +# CONFIG_XZ_DEC_POWERPC is not set +# CONFIG_XZ_DEC_IA64 is not set +# CONFIG_XZ_DEC_ARM is not set +# CONFIG_XZ_DEC_ARMTHUMB is not set +# CONFIG_XZ_DEC_SPARC is not set CONFIG_DYNAMIC_DEBUG=y -CONFIG_DEBUG_FS=y +# CONFIG_DEBUG_MISC is not set CONFIG_MAGIC_SYSRQ=y +CONFIG_DEBUG_FS=y # CONFIG_SCHED_DEBUG is not set -# CONFIG_DEBUG_PREEMPT is not set # CONFIG_FTRACE is not set # CONFIG_EARLY_PRINTK is not set
Signature · 1 line
2.39.2