Skip to contentSkip to conversation

efi/x86: Avoid bare metal decompressor during EFI boot

PATCH Superseded Ard Biesheuvel 2 participants 32 messages Aug 2, 2023 – Aug 7, 2023

Subsystems (3)

v8 of 9 Superseded Latest is v9 →

lore
Share & tools
lore

Ard Biesheuvel

author maintainer
#0 lore raw

v8 cover efi/x86: Avoid bare metal decompressor during EFI boot

Update the x86 boot path to avoid the bare metal decompressor when booting via the EFI stub. The bare metal decompressor inherits the loader's 1:1 mapping of DRAM when entering in 64-bit mode, and assumes that all of it is mapped read/write/execute, which will no longer be the case on systems built to comply with recently tightened logo requirements (*).

Changes since v7 [10]:
- Rebase onto suggested x86/kexec fix [11] that will most likely land first
- Drop only vaguely relevant i386 head_32.S patch
- Restructure the 32-bit trampoline changes slightly into steps that are clearer and easier to follow.
- Fix wording and placement of comments according to suggestions by Borislav

Changes since v6 [9]:
- add new patch to fix our current reliance on 64-bit GPRs retaining their full width contents across the switch into 32-bit protected mode (with fixes: tag, may need to go to -stable);
- preserve the top half of RSP explicitly, and preserve all callee save registers on the stack across the mode switch; this fixes a reported issue on Ice Lake with kexec (which loads the kernel above 4G)

Changes since v5 [8]:
- reintroduce patch removing redundant RSI pushes and pops from arch/x86/kernel/head_64.S
- avoid bare constant 0x200 for the offset of startup_64() in the decompressor
- rejig SEV/SNP logic in patch #20 once again, to ensure that CPUID calls and VM exits only occur when the active configuration permits it
- improve/clarify some code comments and commit logs
- rebase onto v6.5-rc1

Changes since v4 [7]:
- avoid CPUID calls after protocol negotiation but before configuring exception handling;
- drop patch removing redundant RSI pushes and pops from arch/x86/kernel/head_64.S
- rebase onto -tip x86/cc - the conflicts are mostly trivial and restricted to the last 4 patches in the series, so applying this onto a separate topic branch should be straight-forward as well.

Changes since v3 [6]:
- trivial rebase onto Kirill's unaccepted memory series v13
- test SNP feature mask while running in the EFI boot services, and fail gracefully on a mismatch
- perform only the SEV init after ExitBootServices()

Changes since v2 [4]:
- update prose style to comply with -tip guidelines
- rebased onto Kirill's unaccepted memory series [3]
- add Kirill's ack to 4/5-level paging changes
- perform SEV init and SNP feature check after ExitBootServices(), to avoid corrupting the firmware's own SEV state
- split out preparatory refactor of handover entry code and BSS clearing (patches #1 to #4)

Changes since v1 [2]:
- streamline existing 4/5 level switching code and call it directly from the EFI stub - this is covered by the first 9 patches, which can be applied in isolation, if desired;
- deal with SEV/SNP init explicitly;
- clear BSS when booting via the 'handover protocol'
- switch to kernel CS before calling SEV init code in kernel proper.

---- v1 cover letter follows ----

This series is conceptually a combination of Evgeny's series [0] and mine [1], both of which attempt to make the early decompressor code more amenable to executing in the EFI environment with stricter handling of memory permissions.

My series [1] implemented zboot for x86, by getting rid of the entire x86 decompressor, and replacing it with existing EFI code that does the same but in a generic way. The downside of this is that only EFI boot is supported, making it unviable for distros, which need to support BIOS boot and hybrid EFI boot modes that omit the EFI stub.

Evgeny's series [0] adapted the entire decompressor code flow to allow it to execute in the EFI context as well as the bare metal context, and this involves changes to the 1:1 mapping code and the page fault handlers etc, none of which are really needed when doing EFI boot in the first place.

So this series attempts to occupy the middle ground here: it makes minimal changes to the existing decompressor so some of it can be called from the EFI stub. Then, it reimplements the EFI boot flow to decompress the kernel and boot it directly, without relying on the trampoline allocation code, page table code or page fault handling code. This allows us to get rid of quite a bit of unsavory EFI stub code, and replace it with two clear invocations of the EFI firmware APIs to clear NX restrictions from allocations that have been populated with executable code.

The only code that is being reused is the decompression library itself, along with the minimal ELF parsing that is required to copy the ELF segments in place, and the relocation processing that fixes up absolute symbol references to refer to the correct virtual addresses.

Note that some of Evgeny's changes to clean up the PE/COFF header generation will still be needed, but I've omitted those here for brevity.

(*) IMHO the following developments are likely to occur:
- the Windows boot chain (along with 3rd party drivers) is cleaned up so that it never relies on memory being writable and executable at the same time when running under the EFI boot services;
- the EFI reference implementation gets updated to map all memory NX by default, and to require read-only permissions for executable mappings;
- BIOS vendors incorporate these changes into their codebases, and deploy it more widely than just the 'secure' SKUs;
- OEMs only care about the Windows sticker [5], so they only boot test Windows, which works fine in this more restricted context;
- Linux boot no longer works reliably on new hardware built for Windows unless we clean up our boot chain as well.

Cc Evgeniy Baskov <[email protected]>
Cc Borislav Petkov <[email protected]>
Cc Andy Lutomirski <[email protected]>
Cc Dave Hansen <[email protected]>
Cc Ingo Molnar <[email protected]>
Cc Peter Zijlstra <[email protected]>
Cc Thomas Gleixner <[email protected]>
Cc Alexey Khoroshilov <[email protected]>
Cc Peter Jones <[email protected]>
Cc Gerd Hoffmann <[email protected]>
Cc Dave Young <[email protected]>
Cc Mario Limonciello <[email protected]>
Cc Kees Cook <[email protected]>
Cc Tom Lendacky <[email protected]>
Cc Kirill A. Shutemov <[email protected]>
Cc Linus Torvalds <[email protected]>
Cc Joerg Roedel <[email protected]>

[0] https://lore.kernel.org/all/[email protected]/
[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/all/[email protected]/
[3] https://lore.kernel.org/all/[email protected]/
[4] https://lore.kernel.org/all/[email protected]/
[5] https://techcommunity.microsoft.com/t5/hardware-dev-center/new-uefi-ca-memory-mitigation-requirements-for-signing/ba-p/3608714
[6] https://lore.kernel.org/all/[email protected]/
[7] https://lore.kernel.org/all/[email protected]/
[8] https://lore.kernel.org/all/[email protected]/
[9] https://lore.kernel.org/all/[email protected]/
[10] https://lore.kernel.org/all/[email protected]/
[11] https://lore.kernel.org/all/20230802093927.GAZMokT57anC5jBISK@fat_crate.local/

Ard Biesheuvel (23):
x86/decompressor: Don't rely on upper 32 bits of GPRs being preserved x86/head_64: Store boot_params pointer in callee save register x86/efistub: Branch straight to kernel entry point from C code x86/efistub: Simplify and clean up handover entry code x86/decompressor: Avoid magic offsets for EFI handover entrypoint x86/efistub: Clear BSS in EFI handover protocol entrypoint x86/decompressor: Store boot_params pointer in callee save register x86/decompressor: Assign paging related global variables earlier x86/decompressor: Call trampoline as a normal function x86/decompressor: Use standard calling convention for trampoline x86/decompressor: Avoid the need for a stack in the 32-bit trampoline x86/decompressor: Call trampoline directly from C code x86/decompressor: Only call the trampoline when changing paging levels x86/decompressor: Pass pgtable address to trampoline directly x86/decompressor: Merge trampoline cleanup with switching code x86/efistub: Perform 4/5 level paging switch from the stub x86/efistub: Prefer EFI memory attributes protocol over DXE services
decompress: Use 8 byte alignment
x86/decompressor: Move global symbol references to C code x86/decompressor: Factor out kernel decompression and relocation efi/libstub: Add limit argument to efi_random_alloc() x86/efistub: Perform SNP feature test while running in the firmware x86/efistub: Avoid legacy decompressor when doing EFI boot

 Documentation/arch/x86/boot.rst                |   2 +-
 arch/x86/boot/compressed/Makefile              |   5 +
 arch/x86/boot/compressed/efi_mixed.S           | 107 +++-----
 arch/x86/boot/compressed/head_32.S             |  32 ---
 arch/x86/boot/compressed/head_64.S             | 280 ++++++-------------
 arch/x86/boot/compressed/misc.c                |  44 ++-
 arch/x86/boot/compressed/misc.h                |   2 -
 arch/x86/boot/compressed/pgtable.h             |  10 +-
 arch/x86/boot/compressed/pgtable_64.c          |  87 +++---
 arch/x86/boot/compressed/sev.c                 | 112 ++++----
 arch/x86/include/asm/boot.h                    |   8 +
 arch/x86/include/asm/efi.h                     |   7 +-
 arch/x86/include/asm/sev.h                     |   6 +
 arch/x86/kernel/head_64.S                      |  31 +--
 drivers/firmware/efi/libstub/Makefile          |   1 +
 drivers/firmware/efi/libstub/arm64-stub.c      |   2 +-
 drivers/firmware/efi/libstub/efi-stub-helper.c |   2 +
 drivers/firmware/efi/libstub/efistub.h         |   3 +-
 drivers/firmware/efi/libstub/randomalloc.c     |  10 +-
 drivers/firmware/efi/libstub/x86-5lvl.c        |  95 +++++++
 drivers/firmware/efi/libstub/x86-stub.c        | 285 +++++++++++---------
 drivers/firmware/efi/libstub/x86-stub.h        |  17 ++
 drivers/firmware/efi/libstub/zboot.c           |   2 +-
 include/linux/decompress/mm.h                  |   2 +-
 24 files changed, 588 insertions(+), 564 deletions(-)
 create mode 100644 drivers/firmware/efi/libstub/x86-5lvl.c
 create mode 100644 drivers/firmware/efi/libstub/x86-stub.h
Signature · 1 line
2.39.2
author maintainer
#1 lore raw

PATCH v8 1/23 x86/decompressor: Don't rely on upper 32 bits of GPRs being preserved

The 4-to-5 level mode switch trampoline disables long mode and paging in order to be able to flick the LA57 bit. According to section 3.4.1.1 of the x86 architecture manual [0], 64-bit GPRs might not retain the upper 32 bits of their contents across such a mode switch.

Given that RBP, RBX and RSI are live at this point, preserve them on the stack, along with the return address that might be above 4G as well.

[0] Intel® 64 and IA-32 Architectures Software Developer’s Manual, Volume 1: Basic Architecture

"Because the upper 32 bits of 64-bit general-purpose registers are
undefined in 32-bit modes, the upper 32 bits of any general-purpose register are not preserved when switching from 64-bit mode to a 32-bit mode (to protected mode or compatibility mode). Software must not depend on these bits to maintain a value after a 64-bit to 32-bit mode switch."

Fixes 194a9749c73d650c ("x86/boot/compressed/64: Handle 5-level paging boot if kernel is above 4G")
---
 arch/x86/boot/compressed/head_64.S | 30 +++++++++++++++-----
 1 file changed, 23 insertions(+), 7 deletions(-)
arch/x86/boot/compressed/head_64.S +23 -7
index 03c4328a88cbd5d0..f732426d3b483139 100644
@@ -459,11 +459,25 @@ SYM_CODE_START(startup_64)
 	/* Save the trampoline address in RCX */
 	movq	%rax, %rcx
 
+	/* Set up 32-bit addressable stack */
+	leaq	TRAMPOLINE_32BIT_STACK_END(%rcx), %rsp
+
 	/*
-	 * Load the address of trampoline_return() into RDI.
-	 * It will be used by the trampoline to return to the main code.
+	 * Preserve live 64-bit registers on the stack: this is necessary
+	 * because the architecture does not guarantee that GPRs will retain
+	 * their full 64-bit values across a 32-bit mode switch.
+	 */
+	pushq	%rbp
+	pushq	%rbx
+	pushq	%rsi
+
+	/*
+	 * Push the 64-bit address of trampoline_return() onto the new stack.
+	 * It will be used by the trampoline to return to the main code. Due to
+	 * the 32-bit mode switch, it cannot be kept it in a register either.
 	 */
 	leaq	trampoline_return(%rip), %rdi
+	pushq	%rdi
 
 	/* Switch to compatibility mode (CS.L = 0 CS.D = 1) via far return */
 	pushq	$__KERNEL32_CS
@@ -471,6 +485,11 @@ SYM_CODE_START(startup_64)
 	pushq	%rax
 	lretq
 trampoline_return:
+	/* Restore live 64-bit registers */
+	popq	%rsi
+	popq	%rbx
+	popq	%rbp
+
 	/* Restore the stack, the 32-bit trampoline uses its own stack */
 	leaq	rva(boot_stack_end)(%rbx), %rsp
 
@@ -582,7 +601,7 @@ SYM_FUNC_END(.Lrelocated)
 /*
  * This is the 32-bit trampoline that will be copied over to low memory.
  *
- * RDI contains the return address (might be above 4G).
+ * Return address is at the top of the stack (might be above 4G).
  * ECX contains the base address of the trampoline memory.
  * Non zero RDX means trampoline needs to enable 5-level paging.
  */
@@ -592,9 +611,6 @@ SYM_CODE_START(trampoline_32bit_src)
 	movl	%eax, %ds
 	movl	%eax, %ss
 
-	/* Set up new stack */
-	leal	TRAMPOLINE_32BIT_STACK_END(%ecx), %esp
-
 	/* Disable paging */
 	movl	%cr0, %eax
 	btrl	$X86_CR0_PG_BIT, %eax
@@ -671,7 +687,7 @@ SYM_CODE_END(trampoline_32bit_src)
 	.code64
 SYM_FUNC_START_LOCAL_NOALIGN(.Lpaging_enabled)
 	/* Return from the trampoline */
-	jmp	*%rdi
+	retq
 SYM_FUNC_END(.Lpaging_enabled)
 
 	/*
Signature · 1 line
2.39.2
author maintainer
#2 lore raw

PATCH v8 2/23 x86/head_64: Store boot_params pointer in callee save register

In reply to Ard Biesheuvel

Instead of pushing/popping %RSI to/from the stack every time a function is called from startup_64(), store it in a callee preserved register and grab it from there when its value is actually needed.

---
 arch/x86/kernel/head_64.S | 31 +++++++-------------
 1 file changed, 11 insertions(+), 20 deletions(-)
arch/x86/kernel/head_64.S +11 -20
index c5b9289837dcbad2..18b07ab2e8a8ab08 100644
@@ -51,7 +51,9 @@ SYM_CODE_START_NOALIGN(startup_64)
 	 * for us.  These identity mapped page tables map all of the
 	 * kernel pages and possibly all of memory.
 	 *
-	 * %rsi holds a physical pointer to real_mode_data.
+	 * %RSI holds the physical address of the boot_params structure
+	 * provided by the bootloader. Preserve it in %R15 so C function calls
+	 * will not clobber it.
 	 *
 	 * We come here either directly from a 64bit bootloader, or from
 	 * arch/x86/boot/compressed/head_64.S.
@@ -62,6 +64,7 @@ SYM_CODE_START_NOALIGN(startup_64)
 	 * compiled to run at we first fixup the physical addresses in our page
 	 * tables and then reload them.
 	 */
+	mov	%rsi, %r15
 
 	/* Set up the stack for verify_cpu() */
 	leaq	(__end_init_task - PTREGS_SIZE)(%rip), %rsp
@@ -75,9 +78,7 @@ SYM_CODE_START_NOALIGN(startup_64)
 	shrq	$32,  %rdx
 	wrmsr
 
-	pushq	%rsi
 	call	startup_64_setup_env
-	popq	%rsi
 
 	/* Now switch to __KERNEL_CS so IRET works reliably */
 	pushq	$__KERNEL_CS
@@ -93,12 +94,10 @@ SYM_CODE_START_NOALIGN(startup_64)
 	 * Activate SEV/SME memory encryption if supported/enabled. This needs to
 	 * be done now, since this also includes setup of the SEV-SNP CPUID table,
 	 * which needs to be done before any CPUID instructions are executed in
-	 * subsequent code.
+	 * subsequent code. Pass the boot_params pointer as the first argument.
 	 */
-	movq	%rsi, %rdi
-	pushq	%rsi
+	movq	%r15, %rdi
 	call	sme_enable
-	popq	%rsi
 #endif
 
 	/* Sanitize CPU configuration */
@@ -111,9 +110,7 @@ SYM_CODE_START_NOALIGN(startup_64)
 	 * programmed into CR3.
 	 */
 	leaq	_text(%rip), %rdi
-	pushq	%rsi
 	call	__startup_64
-	popq	%rsi
 
 	/* Form the CR3 value being sure to include the CR3 modifier */
 	addq	$(early_top_pgt - __START_KERNEL_map), %rax
@@ -127,8 +124,6 @@ SYM_CODE_START(secondary_startup_64)
 	 * At this point the CPU runs in 64bit mode CS.L = 1 CS.D = 0,
 	 * and someone has loaded a mapped page table.
 	 *
-	 * %rsi holds a physical pointer to real_mode_data.
-	 *
 	 * We come here either from startup_64 (using physical addresses)
 	 * or from trampoline.S (using virtual addresses).
 	 *
@@ -153,6 +148,9 @@ SYM_INNER_LABEL(secondary_startup_64_no_verify, SYM_L_GLOBAL)
 	UNWIND_HINT_END_OF_STACK
 	ANNOTATE_NOENDBR
 
+	/* Clear %R15 which holds the boot_params pointer on the boot CPU */
+	xorq	%r15, %r15
+
 	/*
 	 * Retrieve the modifier (SME encryption mask if SME is active) to be
 	 * added to the initial pgdir entry that will be programmed into CR3.
@@ -199,13 +197,9 @@ SYM_INNER_LABEL(secondary_startup_64_no_verify, SYM_L_GLOBAL)
 	 * hypervisor could lie about the C-bit position to perform a ROP
 	 * attack on the guest by writing to the unencrypted stack and wait for
 	 * the next RET instruction.
-	 * %rsi carries pointer to realmode data and is callee-clobbered. Save
-	 * and restore it.
 	 */
-	pushq	%rsi
 	movq	%rax, %rdi
 	call	sev_verify_cbit
-	popq	%rsi
 
 	/*
 	 * Switch to new page-table
@@ -365,9 +359,7 @@ SYM_INNER_LABEL(secondary_startup_64_no_verify, SYM_L_GLOBAL)
 	wrmsr
 
 	/* Setup and Load IDT */
-	pushq	%rsi
 	call	early_setup_idt
-	popq	%rsi
 
 	/* Check if nx is implemented */
 	movl	$0x80000001, %eax
@@ -403,9 +395,8 @@ SYM_INNER_LABEL(secondary_startup_64_no_verify, SYM_L_GLOBAL)
 	pushq $0
 	popfq
 
-	/* rsi is pointer to real mode structure with interesting info.
-	   pass it to C */
-	movq	%rsi, %rdi
+	/* Pass the boot_params pointer as first argument */
+	movq	%r15, %rdi
 
 .Ljump_to_C_code:
 	/*
Signature · 1 line
2.39.2
author maintainer
#3 lore raw

PATCH v8 3/23 x86/efistub: Branch straight to kernel entry point from C code

In reply to Ard Biesheuvel

Instead of returning to the calling code in assembler that does nothing more than perform an indirect call with the boot_params pointer in register ESI/RSI, perform the jump directly from the EFI stub C code. This will allow the asm entrypoint code to be dropped entirely in subsequent patches.

---
 drivers/firmware/efi/libstub/x86-stub.c | 22 +++++++++++++++-----
 1 file changed, 17 insertions(+), 5 deletions(-)
drivers/firmware/efi/libstub/x86-stub.c +17 -5
index 220be75a5cdc1f4c..40a10db2d85e7942 100644
@@ -290,7 +290,7 @@ adjust_memory_range_protection(unsigned long start, unsigned long size)
 #define TRAMPOLINE_PLACEMENT_BASE ((128 - 8)*1024)
 #define TRAMPOLINE_PLACEMENT_SIZE (640*1024 - (128 - 8)*1024)
 
-void startup_32(struct boot_params *boot_params);
+extern const u8 startup_32[], startup_64[];
 
 static void
 setup_memory_protection(unsigned long image_base, unsigned long image_size)
@@ -803,10 +803,19 @@ static efi_status_t exit_boot(struct boot_params *boot_params, void *handle)
 	return EFI_SUCCESS;
 }
 
+static void __noreturn enter_kernel(unsigned long kernel_addr,
+				    struct boot_params *boot_params)
+{
+	/* enter decompressed kernel with boot_params pointer in RSI/ESI */
+	asm("jmp *%0"::"r"(kernel_addr), "S"(boot_params));
+
+	unreachable();
+}
+
 /*
- * On success, we return the address of startup_32, which has potentially been
- * relocated by efi_relocate_kernel.
- * On failure, we exit to the firmware via efi_exit instead of returning.
+ * On success, this routine will jump to the relocated image directly and never
+ * return.  On failure, it will exit to the firmware via efi_exit() instead of
+ * returning.
  */
 asmlinkage unsigned long efi_main(efi_handle_t handle,
 				  efi_system_table_t *sys_table_arg,
@@ -950,7 +959,10 @@ asmlinkage unsigned long efi_main(efi_handle_t handle,
 		goto fail;
 	}
 
-	return bzimage_addr;
+	if (IS_ENABLED(CONFIG_X86_64))
+		bzimage_addr += startup_64 - startup_32;
+
+	enter_kernel(bzimage_addr, boot_params);
 fail:
 	efi_err("efi_main() failed!\n");
 
Signature · 1 line
2.39.2
author maintainer
#4 lore raw

PATCH v8 4/23 x86/efistub: Simplify and clean up handover entry code

In reply to Ard Biesheuvel

Now that the EFI entry code in assembler is only used by the optional and deprecated EFI handover protocol, and given that the EFI stub C code no longer returns to it, most of it can simply be dropped.

While at it, clarify the symbol naming, by merging efi_main() and efi_stub_entry(), making the latter the shared entry point for all different boot modes that enter via the EFI stub.

The efi32_stub_entry() and efi64_stub_entry() names are referenced explicitly by the tooling that populates the setup header, so these must be retained, but can be emitted as aliases of efi_stub_entry() where appropriate.

---
 Documentation/arch/x86/boot.rst         |  2 +-
 arch/x86/boot/compressed/efi_mixed.S    | 22 +++++++++++---------
 arch/x86/boot/compressed/head_32.S      | 11 ----------
 arch/x86/boot/compressed/head_64.S      | 12 ++---------
 drivers/firmware/efi/libstub/x86-stub.c | 20 ++++++++++++++----
 5 files changed, 31 insertions(+), 36 deletions(-)
Documentation/arch/x86/boot.rst +1 -1
index 33520ecdb37abfda..cdbca15a4fc23833 100644
@@ -1417,7 +1417,7 @@ execution context provided by the EFI firmware.
 
 The function prototype for the handover entry point looks like this::
 
-    efi_main(void *handle, efi_system_table_t *table, struct boot_params *bp)
+    efi_stub_entry(void *handle, efi_system_table_t *table, struct boot_params *bp)
 
 'handle' is the EFI image handle passed to the boot loader by the EFI
 firmware, 'table' is the EFI system table - these are the first two
arch/x86/boot/compressed/efi_mixed.S +12 -10
index 4ca70bf93dc0bdcd..dcc562c8f7f35162 100644
@@ -26,8 +26,8 @@
  * When booting in 64-bit mode on 32-bit EFI firmware, startup_64_mixed_mode()
  * is the first thing that runs after switching to long mode. Depending on
  * whether the EFI handover protocol or the compat entry point was used to
- * enter the kernel, it will either branch to the 64-bit EFI handover
- * entrypoint at offset 0x390 in the image, or to the 64-bit EFI PE/COFF
+ * enter the kernel, it will either branch to the common 64-bit EFI stub
+ * entrypoint efi_stub_entry() directly, or via the 64-bit EFI PE/COFF
  * entrypoint efi_pe_entry(). In the former case, the bootloader must provide a
  * struct bootparams pointer as the third argument, so the presence of such a
  * pointer is used to disambiguate.
@@ -37,21 +37,23 @@
  *  | efi32_pe_entry   |---->|            |            |       +-----------+--+
  *  +------------------+     |            |     +------+----------------+  |
  *                           | startup_32 |---->| startup_64_mixed_mode |  |
- *  +------------------+     |            |     +------+----------------+  V
- *  | efi32_stub_entry |---->|            |            |     +------------------+
- *  +------------------+     +------------+            +---->| efi64_stub_entry |
- *                                                           +-------------+----+
- *                           +------------+     +----------+               |
- *                           | startup_64 |<----| efi_main |<--------------+
- *                           +------------+     +----------+
+ *  +------------------+     |            |     +------+----------------+  |
+ *  | efi32_stub_entry |---->|            |            |                   |
+ *  +------------------+     +------------+            |                   |
+ *                                                     V                   |
+ *                           +------------+     +----------------+         |
+ *                           | startup_64 |<----| efi_stub_entry |<--------+
+ *                           +------------+     +----------------+
  */
 SYM_FUNC_START(startup_64_mixed_mode)
 	lea	efi32_boot_args(%rip), %rdx
 	mov	0(%rdx), %edi
 	mov	4(%rdx), %esi
+#ifdef CONFIG_EFI_HANDOVER_PROTOCOL
 	mov	8(%rdx), %edx		// saved bootparams pointer
 	test	%edx, %edx
-	jnz	efi64_stub_entry
+	jnz	efi_stub_entry
+#endif
 	/*
 	 * efi_pe_entry uses MS calling convention, which requires 32 bytes of
 	 * shadow space on the stack even if all arguments are passed in
arch/x86/boot/compressed/head_32.S +0 -11
index 987ae727cf9f0d04..8876ffe30e9a4819 100644
@@ -150,17 +150,6 @@ SYM_FUNC_START(startup_32)
 	jmp	*%eax
 SYM_FUNC_END(startup_32)
 
-#ifdef CONFIG_EFI_STUB
-SYM_FUNC_START(efi32_stub_entry)
-	add	$0x4, %esp
-	movl	8(%esp), %esi	/* save boot_params pointer */
-	call	efi_main
-	/* efi_main returns the possibly relocated address of startup_32 */
-	jmp	*%eax
-SYM_FUNC_END(efi32_stub_entry)
-SYM_FUNC_ALIAS(efi_stub_entry, efi32_stub_entry)
-#endif
-
 	.text
 SYM_FUNC_START_LOCAL_NOALIGN(.Lrelocated)
 
arch/x86/boot/compressed/head_64.S +2 -10
index f732426d3b483139..e6880208b9a1b90a 100644
@@ -542,19 +542,11 @@ trampoline_return:
 	jmp	*%rax
 SYM_CODE_END(startup_64)
 
-#ifdef CONFIG_EFI_STUB
-#ifdef CONFIG_EFI_HANDOVER_PROTOCOL
+#if IS_ENABLED(CONFIG_EFI_MIXED) && IS_ENABLED(CONFIG_EFI_HANDOVER_PROTOCOL)
 	.org 0x390
-#endif
 SYM_FUNC_START(efi64_stub_entry)
-	and	$~0xf, %rsp			/* realign the stack */
-	movq	%rdx, %rbx			/* save boot_params pointer */
-	call	efi_main
-	movq	%rbx,%rsi
-	leaq	rva(startup_64)(%rax), %rax
-	jmp	*%rax
+	jmp	efi_stub_entry
 SYM_FUNC_END(efi64_stub_entry)
-SYM_FUNC_ALIAS(efi_stub_entry, efi64_stub_entry)
 #endif
 
 	.text
drivers/firmware/efi/libstub/x86-stub.c +16 -4
index 40a10db2d85e7942..3f3b3edf7a387d7c 100644
@@ -817,9 +817,9 @@ static void __noreturn enter_kernel(unsigned long kernel_addr,
  * return.  On failure, it will exit to the firmware via efi_exit() instead of
  * returning.
  */
-asmlinkage unsigned long efi_main(efi_handle_t handle,
-				  efi_system_table_t *sys_table_arg,
-				  struct boot_params *boot_params)
+void __noreturn efi_stub_entry(efi_handle_t handle,
+			       efi_system_table_t *sys_table_arg,
+			       struct boot_params *boot_params)
 {
 	unsigned long bzimage_addr = (unsigned long)startup_32;
 	unsigned long buffer_start, buffer_end;
@@ -964,7 +964,19 @@ asmlinkage unsigned long efi_main(efi_handle_t handle,
 
 	enter_kernel(bzimage_addr, boot_params);
 fail:
-	efi_err("efi_main() failed!\n");
+	efi_err("efi_stub_entry() failed!\n");
 
 	efi_exit(handle, status);
 }
+
+#ifdef CONFIG_EFI_HANDOVER_PROTOCOL
+#ifndef CONFIG_EFI_MIXED
+extern __alias(efi_stub_entry)
+void efi32_stub_entry(efi_handle_t handle, efi_system_table_t *sys_table_arg,
+		      struct boot_params *boot_params);
+
+extern __alias(efi_stub_entry)
+void efi64_stub_entry(efi_handle_t handle, efi_system_table_t *sys_table_arg,
+		      struct boot_params *boot_params);
+#endif
+#endif
Signature · 1 line
2.39.2
author maintainer
#5 lore raw

PATCH v8 5/23 x86/decompressor: Avoid magic offsets for EFI handover entrypoint

In reply to Ard Biesheuvel

The native 32-bit or 64-bit EFI handover protocol entrypoint offset relative to the respective startup_32/64 address is described in boot_params as handover_offset, so that the special Linux/x86 aware EFI loader can find it there.

When mixed mode is enabled, this single field has to describe this offset for both the 32-bit and 64-bit entrypoints, so their respective relative offsets have to be identical. Given that startup_32 and startup_64 are 0x200 bytes apart, and the EFI handover entrypoint resides at a fixed offset, the 32-bit and 64-bit versions of those entrypoints must be exactly 0x200 bytes apart as well.

Currently, hard-coded fixed offsets are used to ensure this, but it is sufficient to emit the 64-bit entrypoint 0x200 bytes after the 32-bit one, wherever it happens to reside. This allows this code (which is now EFI mixed mode specific) to be moved into efi_mixed.S and out of the startup code in head_64.S.

---
 arch/x86/boot/compressed/efi_mixed.S | 20 +++++++++++++++++++-
 arch/x86/boot/compressed/head_64.S   | 18 ------------------
 2 files changed, 19 insertions(+), 19 deletions(-)
arch/x86/boot/compressed/efi_mixed.S +19 -1
index dcc562c8f7f35162..9308b595f6f0a5de 100644
@@ -140,6 +140,16 @@ SYM_FUNC_START(__efi64_thunk)
 SYM_FUNC_END(__efi64_thunk)
 
 	.code32
+#ifdef CONFIG_EFI_HANDOVER_PROTOCOL
+SYM_FUNC_START(efi32_stub_entry)
+	add	$0x4, %esp		/* Discard return address */
+	popl	%ecx
+	popl	%edx
+	popl	%esi
+	jmp	efi32_entry
+SYM_FUNC_END(efi32_stub_entry)
+#endif
+
 /*
  * EFI service pointer must be in %edi.
  *
@@ -220,7 +230,7 @@ SYM_FUNC_END(efi_enter32)
  * stub may still exit and return to the firmware using the Exit() EFI boot
  * service.]
  */
-SYM_FUNC_START(efi32_entry)
+SYM_FUNC_START_LOCAL(efi32_entry)
 	call	1f
 1:	pop	%ebx
 
@@ -320,6 +330,14 @@ SYM_FUNC_START(efi32_pe_entry)
 	RET
 SYM_FUNC_END(efi32_pe_entry)
 
+#ifdef CONFIG_EFI_HANDOVER_PROTOCOL
+	.org	efi32_stub_entry + 0x200
+	.code64
+SYM_FUNC_START_NOALIGN(efi64_stub_entry)
+	jmp	efi_stub_entry
+SYM_FUNC_END(efi64_stub_entry)
+#endif
+
 	.section ".rodata"
 	/* EFI loaded image protocol GUID */
 	.balign 4
arch/x86/boot/compressed/head_64.S +0 -18
index e6880208b9a1b90a..a3f764daf3a3adbc 100644
@@ -294,17 +294,6 @@ SYM_FUNC_START(startup_32)
 	lret
 SYM_FUNC_END(startup_32)
 
-#if IS_ENABLED(CONFIG_EFI_MIXED) && IS_ENABLED(CONFIG_EFI_HANDOVER_PROTOCOL)
-	.org 0x190
-SYM_FUNC_START(efi32_stub_entry)
-	add	$0x4, %esp		/* Discard return address */
-	popl	%ecx
-	popl	%edx
-	popl	%esi
-	jmp	efi32_entry
-SYM_FUNC_END(efi32_stub_entry)
-#endif
-
 	.code64
 	.org 0x200
 SYM_CODE_START(startup_64)
@@ -542,13 +531,6 @@ trampoline_return:
 	jmp	*%rax
 SYM_CODE_END(startup_64)
 
-#if IS_ENABLED(CONFIG_EFI_MIXED) && IS_ENABLED(CONFIG_EFI_HANDOVER_PROTOCOL)
-	.org 0x390
-SYM_FUNC_START(efi64_stub_entry)
-	jmp	efi_stub_entry
-SYM_FUNC_END(efi64_stub_entry)
-#endif
-
 	.text
 SYM_FUNC_START_LOCAL_NOALIGN(.Lrelocated)
 
Signature · 1 line
2.39.2
author maintainer
#6 lore raw

PATCH v8 6/23 x86/efistub: Clear BSS in EFI handover protocol entrypoint

In reply to Ard Biesheuvel

The so-called EFI handover protocol is value-add from the distros that permits a loader to simply copy a PE kernel image into memory and call an alternative entrypoint that is described by an embedded boot_params structure.

Most implementations of this protocol do not bother to check the PE header for minimum alignment, section placement, etc, and therefore also don't clear the image's BSS, or even allocate enough memory for it.

Allocating more memory on the fly is rather difficult, but at least clear the BSS region explicitly when entering in this manner, so that the EFI stub code does not get confused by global variables that were not zero-initialized correctly.

When booting in mixed mode, this BSS clearing must occur before any global state is created, so clear it in the 32-bit asm entry point.

---
 arch/x86/boot/compressed/efi_mixed.S    | 14 +++++++++++++-
 drivers/firmware/efi/libstub/x86-stub.c | 13 +++++++++++--
 2 files changed, 24 insertions(+), 3 deletions(-)
arch/x86/boot/compressed/efi_mixed.S +13 -1
index 9308b595f6f0a5de..8a02a151806df14c 100644
@@ -142,6 +142,18 @@ SYM_FUNC_END(__efi64_thunk)
 	.code32
 #ifdef CONFIG_EFI_HANDOVER_PROTOCOL
 SYM_FUNC_START(efi32_stub_entry)
+	call	1f
+1:	popl	%ecx
+
+	/* Clear BSS */
+	xorl	%eax, %eax
+	leal	(_bss - 1b)(%ecx), %edi
+	leal	(_ebss - 1b)(%ecx), %ecx
+	subl	%edi, %ecx
+	shrl	$2, %ecx
+	cld
+	rep	stosl
+
 	add	$0x4, %esp		/* Discard return address */
 	popl	%ecx
 	popl	%edx
@@ -334,7 +346,7 @@ SYM_FUNC_END(efi32_pe_entry)
 	.org	efi32_stub_entry + 0x200
 	.code64
 SYM_FUNC_START_NOALIGN(efi64_stub_entry)
-	jmp	efi_stub_entry
+	jmp	efi_handover_entry
 SYM_FUNC_END(efi64_stub_entry)
 #endif
 
drivers/firmware/efi/libstub/x86-stub.c +11 -2
index 3f3b3edf7a387d7c..9247dbc7dbbd12ef 100644
@@ -970,12 +970,21 @@ void __noreturn efi_stub_entry(efi_handle_t handle,
 }
 
 #ifdef CONFIG_EFI_HANDOVER_PROTOCOL
+void efi_handover_entry(efi_handle_t handle, efi_system_table_t *sys_table_arg,
+			struct boot_params *boot_params)
+{
+	extern char _bss[], _ebss[];
+
+	memset(_bss, 0, _ebss - _bss);
+	efi_stub_entry(handle, sys_table_arg, boot_params);
+}
+
 #ifndef CONFIG_EFI_MIXED
-extern __alias(efi_stub_entry)
+extern __alias(efi_handover_entry)
 void efi32_stub_entry(efi_handle_t handle, efi_system_table_t *sys_table_arg,
 		      struct boot_params *boot_params);
 
-extern __alias(efi_stub_entry)
+extern __alias(efi_handover_entry)
 void efi64_stub_entry(efi_handle_t handle, efi_system_table_t *sys_table_arg,
 		      struct boot_params *boot_params);
 #endif
Signature · 1 line
2.39.2
author maintainer
#7 lore raw

PATCH v8 7/23 x86/decompressor: Store boot_params pointer in callee save register

In reply to Ard Biesheuvel

Instead of pushing and popping %RSI several times to preserve the struct boot_params pointer across the execution of the startup code, move it into a callee save register before the first call into C, and copy it back when needed.

---
 arch/x86/boot/compressed/head_64.S | 42 ++++++++------------
 1 file changed, 16 insertions(+), 26 deletions(-)
arch/x86/boot/compressed/head_64.S +16 -26
index a3f764daf3a3adbc..19bf810409e2aa62 100644
@@ -405,10 +405,14 @@ SYM_CODE_START(startup_64)
 	lretq
 
 .Lon_kernel_cs:
+	/*
+	 * RSI holds a pointer to a boot_params structure provided by the
+	 * loader, and this needs to be preserved across C function calls. So
+	 * move it into a callee saved register.
+	 */
+	movq	%rsi, %r15
 
-	pushq	%rsi
 	call	load_stage1_idt
-	popq	%rsi
 
 #ifdef CONFIG_AMD_MEM_ENCRYPT
 	/*
@@ -419,12 +423,10 @@ SYM_CODE_START(startup_64)
 	 * CPUID instructions being issued, so go ahead and do that now via
 	 * sev_enable(), which will also handle the rest of the SEV-related
 	 * detection/setup to ensure that has been done in advance of any dependent
-	 * code.
+	 * code. Pass the boot_params pointer as the first argument.
 	 */
-	pushq	%rsi
-	movq	%rsi, %rdi		/* real mode address */
+	movq	%r15, %rdi
 	call	sev_enable
-	popq	%rsi
 #endif
 
 	/*
@@ -437,13 +439,10 @@ SYM_CODE_START(startup_64)
 	 *   - Non zero RDX means trampoline needs to enable 5-level
 	 *     paging.
 	 *
-	 * RSI holds real mode data and needs to be preserved across
-	 * this function call.
+	 * Pass the boot_params pointer as the first argument.
 	 */
-	pushq	%rsi
-	movq	%rsi, %rdi		/* real mode address */
+	movq	%r15, %rdi
 	call	paging_prepare
-	popq	%rsi
 
 	/* Save the trampoline address in RCX */
 	movq	%rax, %rcx
@@ -456,9 +455,9 @@ SYM_CODE_START(startup_64)
 	 * because the architecture does not guarantee that GPRs will retain
 	 * their full 64-bit values across a 32-bit mode switch.
 	 */
+	pushq	%r15
 	pushq	%rbp
 	pushq	%rbx
-	pushq	%rsi
 
 	/*
 	 * Push the 64-bit address of trampoline_return() onto the new stack.
@@ -475,9 +474,9 @@ SYM_CODE_START(startup_64)
 	lretq
 trampoline_return:
 	/* Restore live 64-bit registers */
-	popq	%rsi
 	popq	%rbx
 	popq	%rbp
+	popq	%r15
 
 	/* Restore the stack, the 32-bit trampoline uses its own stack */
 	leaq	rva(boot_stack_end)(%rbx), %rsp
@@ -487,14 +486,9 @@ trampoline_return:
 	 *
 	 * RDI is address of the page table to use instead of page table
 	 * in trampoline memory (if required).
-	 *
-	 * RSI holds real mode data and needs to be preserved across
-	 * this function call.
 	 */
-	pushq	%rsi
 	leaq	rva(top_pgtable)(%rbx), %rdi
 	call	cleanup_trampoline
-	popq	%rsi
 
 	/* Zero EFLAGS */
 	pushq	$0
@@ -504,7 +498,6 @@ trampoline_return:
  * Copy the compressed kernel to the end of our buffer
  * where decompression in place becomes safe.
  */
-	pushq	%rsi
 	leaq	(_bss-8)(%rip), %rsi
 	leaq	rva(_bss-8)(%rbx), %rdi
 	movl	$(_bss - startup_32), %ecx
@@ -512,7 +505,6 @@ trampoline_return:
 	std
 	rep	movsq
 	cld
-	popq	%rsi
 
 	/*
 	 * The GDT may get overwritten either during the copy we just did or
@@ -544,30 +536,28 @@ SYM_FUNC_START_LOCAL_NOALIGN(.Lrelocated)
 	shrq	$3, %rcx
 	rep	stosq
 
-	pushq	%rsi
 	call	load_stage2_idt
 
 	/* Pass boot_params to initialize_identity_maps() */
-	movq	(%rsp), %rdi
+	movq	%r15, %rdi
 	call	initialize_identity_maps
-	popq	%rsi
 
 /*
  * Do the extraction, and jump to the new kernel..
  */
-	pushq	%rsi			/* Save the real mode argument */
-	movq	%rsi, %rdi		/* real mode address */
+	/* pass struct boot_params pointer */
+	movq	%r15, %rdi
 	leaq	boot_heap(%rip), %rsi	/* malloc area for uncompression */
 	leaq	input_data(%rip), %rdx  /* input_data */
 	movl	input_len(%rip), %ecx	/* input_len */
 	movq	%rbp, %r8		/* output target address */
 	movl	output_len(%rip), %r9d	/* decompressed length, end of relocs */
 	call	extract_kernel		/* returns kernel entry point in %rax */
-	popq	%rsi
 
 /*
  * Jump to the decompressed kernel.
  */
+	movq	%r15, %rsi
 	jmp	*%rax
 SYM_FUNC_END(.Lrelocated)
 
Signature · 1 line
2.39.2
author maintainer
#8 lore raw

PATCH v8 8/23 x86/decompressor: Assign paging related global variables earlier

In reply to Ard Biesheuvel

There is no need to defer the assignment of the paging related global variabled 'pgdir_shift' and 'ptrs_per_p4d' until after the trampoline is cleaned up, so assign them as soon as it is clear that 5-level paging will be enabled.

---
 arch/x86/boot/compressed/misc.h       |  2 --
 arch/x86/boot/compressed/pgtable_64.c | 14 +++++---------
 2 files changed, 5 insertions(+), 11 deletions(-)
arch/x86/boot/compressed/misc.h +0 -2
index 964fe903a1cdccdc..cc70d3fb90497ed8 100644
@@ -179,9 +179,7 @@ static inline int count_immovable_mem_regions(void) { return 0; }
 #endif
 
 /* ident_map_64.c */
-#ifdef CONFIG_X86_5LEVEL
 extern unsigned int __pgtable_l5_enabled, pgdir_shift, ptrs_per_p4d;
-#endif
 extern void kernel_add_identity_map(unsigned long start, unsigned long end);
 
 /* Used by PAGE_KERN* macros: */
arch/x86/boot/compressed/pgtable_64.c +5 -9
index 2ac12ff4111bf8c0..f8092d3244c9559b 100644
@@ -130,6 +130,11 @@ struct paging_config paging_prepare(void *rmode)
 			native_cpuid_eax(0) >= 7 &&
 			(native_cpuid_ecx(7) & (1 << (X86_FEATURE_LA57 & 31)))) {
 		paging_config.l5_required = 1;
+
+		/* Initialize variables for 5-level paging */
+		__pgtable_l5_enabled = 1;
+		pgdir_shift = 48;
+		ptrs_per_p4d = 512;
 	}
 
 	paging_config.trampoline_start = find_trampoline_placement();
@@ -206,13 +211,4 @@ void cleanup_trampoline(void *pgtable)
 
 	/* Restore trampoline memory */
 	memcpy(trampoline_32bit, trampoline_save, TRAMPOLINE_32BIT_SIZE);
-
-	/* Initialize variables for 5-level paging */
-#ifdef CONFIG_X86_5LEVEL
-	if (__read_cr4() & X86_CR4_LA57) {
-		__pgtable_l5_enabled = 1;
-		pgdir_shift = 48;
-		ptrs_per_p4d = 512;
-	}
-#endif
 }
Signature · 1 line
2.39.2
author maintainer
#9 lore raw

PATCH v8 9/23 x86/decompressor: Call trampoline as a normal function

In reply to Ard Biesheuvel

Move the long return to switch to 32-bit mode into the trampoline code so it can be called as an ordinary function. This will allow it to be called directly from C code in a subsequent patch.

While at it, reorganize the code somewhat to keep the prologue and epilogue of the function together, making the code a bit easier to follow. Also, given that the trampoline is now entered in 64-bit mode, a simple RIP-relative reference can be used to take the address of the exit point.

---
 arch/x86/boot/compressed/head_64.S | 79 +++++++++-----------
 arch/x86/boot/compressed/pgtable.h |  2 +-
 2 files changed, 36 insertions(+), 45 deletions(-)
arch/x86/boot/compressed/head_64.S +35 -44
index 19bf810409e2aa62..91b5eee306148f9a 100644
@@ -447,39 +447,8 @@ SYM_CODE_START(startup_64)
 	/* Save the trampoline address in RCX */
 	movq	%rax, %rcx
 
-	/* Set up 32-bit addressable stack */
-	leaq	TRAMPOLINE_32BIT_STACK_END(%rcx), %rsp
-
-	/*
-	 * Preserve live 64-bit registers on the stack: this is necessary
-	 * because the architecture does not guarantee that GPRs will retain
-	 * their full 64-bit values across a 32-bit mode switch.
-	 */
-	pushq	%r15
-	pushq	%rbp
-	pushq	%rbx
-
-	/*
-	 * Push the 64-bit address of trampoline_return() onto the new stack.
-	 * It will be used by the trampoline to return to the main code. Due to
-	 * the 32-bit mode switch, it cannot be kept it in a register either.
-	 */
-	leaq	trampoline_return(%rip), %rdi
-	pushq	%rdi
-
-	/* Switch to compatibility mode (CS.L = 0 CS.D = 1) via far return */
-	pushq	$__KERNEL32_CS
 	leaq	TRAMPOLINE_32BIT_CODE_OFFSET(%rax), %rax
-	pushq	%rax
-	lretq
-trampoline_return:
-	/* Restore live 64-bit registers */
-	popq	%rbx
-	popq	%rbp
-	popq	%r15
-
-	/* Restore the stack, the 32-bit trampoline uses its own stack */
-	leaq	rva(boot_stack_end)(%rbx), %rsp
+	call	*%rax
 
 	/*
 	 * cleanup_trampoline() would restore trampoline memory.
@@ -561,7 +530,6 @@ SYM_FUNC_START_LOCAL_NOALIGN(.Lrelocated)
 	jmp	*%rax
 SYM_FUNC_END(.Lrelocated)
 
-	.code32
 /*
  * This is the 32-bit trampoline that will be copied over to low memory.
  *
@@ -570,6 +538,39 @@ SYM_FUNC_END(.Lrelocated)
  * Non zero RDX means trampoline needs to enable 5-level paging.
  */
 SYM_CODE_START(trampoline_32bit_src)
+	/*
+	 * Preserve live 64-bit registers on the stack: this is necessary
+	 * because the architecture does not guarantee that GPRs will retain
+	 * their full 64-bit values across a 32-bit mode switch.
+	 */
+	pushq	%r15
+	pushq	%rbp
+	pushq	%rbx
+
+	/* Set up 32-bit addressable stack and push the old RSP value */
+	leaq	(TRAMPOLINE_32BIT_STACK_END - 8)(%rcx), %rbx
+	movq	%rsp, (%rbx)
+	movq	%rbx, %rsp
+
+	/* Take the address of the trampoline exit code */
+	leaq	.Lret(%rip), %rbx
+
+	/* Switch to compatibility mode (CS.L = 0 CS.D = 1) via far return */
+	pushq	$__KERNEL32_CS
+	leaq	0f(%rip), %rax
+	pushq	%rax
+	lretq
+
+.Lret:
+	/* Restore the preserved 64-bit registers */
+	movq	(%rsp), %rsp
+	popq	%rbx
+	popq	%rbp
+	popq	%r15
+	retq
+
+	.code32
+0:
 	/* Set up data and stack segments */
 	movl	$__KERNEL_DS, %eax
 	movl	%eax, %ds
@@ -633,12 +634,9 @@ SYM_CODE_START(trampoline_32bit_src)
 1:
 	movl	%eax, %cr4
 
-	/* Calculate address of paging_enabled() once we are executing in the trampoline */
-	leal	.Lpaging_enabled - trampoline_32bit_src + TRAMPOLINE_32BIT_CODE_OFFSET(%ecx), %eax
-
 	/* Prepare the stack for far return to Long Mode */
 	pushl	$__KERNEL_CS
-	pushl	%eax
+	pushl	%ebx
 
 	/* Enable paging again. */
 	movl	%cr0, %eax
@@ -648,12 +646,6 @@ SYM_CODE_START(trampoline_32bit_src)
 	lret
 SYM_CODE_END(trampoline_32bit_src)
 
-	.code64
-SYM_FUNC_START_LOCAL_NOALIGN(.Lpaging_enabled)
-	/* Return from the trampoline */
-	retq
-SYM_FUNC_END(.Lpaging_enabled)
-
 	/*
          * The trampoline code has a size limit.
          * Make sure we fail to compile if the trampoline code grows
@@ -661,7 +653,6 @@ SYM_FUNC_END(.Lpaging_enabled)
 	 */
 	.org	trampoline_32bit_src + TRAMPOLINE_32BIT_CODE_SIZE
 
-	.code32
 SYM_FUNC_START_LOCAL_NOALIGN(.Lno_longmode)
 	/* This isn't an x86-64 CPU, so hang intentionally, we cannot continue */
 1:
arch/x86/boot/compressed/pgtable.h +1 -1
index cc9b2529a08634b4..91dbb99203fbce2d 100644
@@ -6,7 +6,7 @@
 #define TRAMPOLINE_32BIT_PGTABLE_OFFSET	0
 
 #define TRAMPOLINE_32BIT_CODE_OFFSET	PAGE_SIZE
-#define TRAMPOLINE_32BIT_CODE_SIZE	0x80
+#define TRAMPOLINE_32BIT_CODE_SIZE	0xA0
 
 #define TRAMPOLINE_32BIT_STACK_END	TRAMPOLINE_32BIT_SIZE
 
Signature · 1 line
2.39.2
author maintainer
#10 lore raw

PATCH v8 10/23 x86/decompressor: Use standard calling convention for trampoline

In reply to Ard Biesheuvel

Update the trampoline code so its arguments are passed via RDI and RSI, which matches the ordinary SysV calling convention for x86_64. This will allow this code to be called directly from C.

---
 arch/x86/boot/compressed/head_64.S | 27 ++++++++++----------
 arch/x86/boot/compressed/pgtable.h |  2 +-
 2 files changed, 14 insertions(+), 15 deletions(-)
arch/x86/boot/compressed/head_64.S +13 -14
index 91b5eee306148f9a..c47504208105d7d3 100644
@@ -444,9 +444,9 @@ SYM_CODE_START(startup_64)
 	movq	%r15, %rdi
 	call	paging_prepare
 
-	/* Save the trampoline address in RCX */
-	movq	%rax, %rcx
-
+	/* Pass the trampoline address and boolean flag as args #1 and #2 */
+	movq	%rax, %rdi
+	movq	%rdx, %rsi
 	leaq	TRAMPOLINE_32BIT_CODE_OFFSET(%rax), %rax
 	call	*%rax
 
@@ -531,11 +531,14 @@ SYM_FUNC_START_LOCAL_NOALIGN(.Lrelocated)
 SYM_FUNC_END(.Lrelocated)
 
 /*
- * This is the 32-bit trampoline that will be copied over to low memory.
+ * This is the 32-bit trampoline that will be copied over to low memory. It
+ * will be called using the ordinary 64-bit calling convention from code
+ * running in 64-bit mode.
  *
  * Return address is at the top of the stack (might be above 4G).
- * ECX contains the base address of the trampoline memory.
- * Non zero RDX means trampoline needs to enable 5-level paging.
+ * The first argument (EDI) contains the 32-bit addressable base of the
+ * trampoline memory. A non-zero second argument (ESI) means that the
+ * trampoline needs to enable 5-level paging.
  */
 SYM_CODE_START(trampoline_32bit_src)
 	/*
@@ -582,7 +585,7 @@ SYM_CODE_START(trampoline_32bit_src)
 	movl	%eax, %cr0
 
 	/* Check what paging mode we want to be in after the trampoline */
-	testl	%edx, %edx
+	testl	%esi, %esi
 	jz	1f
 
 	/* We want 5-level paging: don't touch CR3 if it already points to 5-level page tables */
@@ -597,21 +600,17 @@ SYM_CODE_START(trampoline_32bit_src)
 	jz	3f
 2:
 	/* Point CR3 to the trampoline's new top level page table */
-	leal	TRAMPOLINE_32BIT_PGTABLE_OFFSET(%ecx), %eax
+	leal	TRAMPOLINE_32BIT_PGTABLE_OFFSET(%edi), %eax
 	movl	%eax, %cr3
 3:
 	/* Set EFER.LME=1 as a precaution in case hypervsior pulls the rug */
-	pushl	%ecx
-	pushl	%edx
 	movl	$MSR_EFER, %ecx
 	rdmsr
 	btsl	$_EFER_LME, %eax
 	/* Avoid writing EFER if no change was made (for TDX guest) */
 	jc	1f
 	wrmsr
-1:	popl	%edx
-	popl	%ecx
-
+1:
 #ifdef CONFIG_X86_MCE
 	/*
 	 * Preserve CR4.MCE if the kernel will enable #MC support.
@@ -628,7 +627,7 @@ SYM_CODE_START(trampoline_32bit_src)
 
 	/* Enable PAE and LA57 (if required) paging modes */
 	orl	$X86_CR4_PAE, %eax
-	testl	%edx, %edx
+	testl	%esi, %esi
 	jz	1f
 	orl	$X86_CR4_LA57, %eax
 1:
arch/x86/boot/compressed/pgtable.h +1 -1
index 91dbb99203fbce2d..4e8cef135226bcbb 100644
@@ -14,7 +14,7 @@
 
 extern unsigned long *trampoline_32bit;
 
-extern void trampoline_32bit_src(void *return_ptr);
+extern void trampoline_32bit_src(void *trampoline, bool enable_5lvl);
 
 #endif /* __ASSEMBLER__ */
 #endif /* BOOT_COMPRESSED_PAGETABLE_H */
Signature · 1 line
2.39.2
author maintainer
#11 lore raw

PATCH v8 11/23 x86/decompressor: Avoid the need for a stack in the 32-bit trampoline

In reply to Ard Biesheuvel

The 32-bit trampoline no longer uses the stack for anything except performing a far return back to long mode, and preserving the caller's stack pointer value. Currently, the trampoline stack is placed in the same page that carries the trampoline code, which means this page must be mapped writable and executable, and the stack is therefore executable as well.

Replace the far return with a far jump, so that the return address can be pre-calculated and patched into the code before it is called. This removes the need for a 32-bit addressable stack entirely, and in a later patch, this will be taken advantage of by removing writable permissions from (and adding executable permissions to) the trampoline code page when booting via the EFI stub.

Note that the value of RSP still needs to be preserved explicitly across the switch into 32-bit mode, as the register may get truncated to 32 bits.

---
 arch/x86/boot/compressed/head_64.S    | 45 ++++++++++++--------
 arch/x86/boot/compressed/pgtable.h    |  4 +-
 arch/x86/boot/compressed/pgtable_64.c | 12 +++++-
 3 files changed, 40 insertions(+), 21 deletions(-)
arch/x86/boot/compressed/head_64.S +27 -18
index c47504208105d7d3..37fd7b7d683d696c 100644
@@ -540,6 +540,7 @@ SYM_FUNC_END(.Lrelocated)
  * trampoline memory. A non-zero second argument (ESI) means that the
  * trampoline needs to enable 5-level paging.
  */
+	.section ".rodata", "a", @progbits
 SYM_CODE_START(trampoline_32bit_src)
 	/*
 	 * Preserve live 64-bit registers on the stack: this is necessary
@@ -550,13 +551,9 @@ SYM_CODE_START(trampoline_32bit_src)
 	pushq	%rbp
 	pushq	%rbx
 
-	/* Set up 32-bit addressable stack and push the old RSP value */
-	leaq	(TRAMPOLINE_32BIT_STACK_END - 8)(%rcx), %rbx
-	movq	%rsp, (%rbx)
-	movq	%rbx, %rsp
-
-	/* Take the address of the trampoline exit code */
-	leaq	.Lret(%rip), %rbx
+	/* Preserve top half of RSP in a legacy mode GPR to avoid truncation */
+	movq	%rsp, %rbx
+	shrq	$32, %rbx
 
 	/* Switch to compatibility mode (CS.L = 0 CS.D = 1) via far return */
 	pushq	$__KERNEL32_CS
@@ -564,9 +561,17 @@ SYM_CODE_START(trampoline_32bit_src)
 	pushq	%rax
 	lretq
 
+	/*
+	 * The 32-bit code below will do a far jump back to long mode and end
+	 * up here after reconfiguring the number of paging levels. First, the
+	 * stack pointer needs to be restored to its full 64-bit value before
+	 * the callee save register contents can be popped from the stack.
+	 */
 .Lret:
+	shlq	$32, %rbx
+	orq	%rbx, %rsp
+
 	/* Restore the preserved 64-bit registers */
-	movq	(%rsp), %rsp
 	popq	%rbx
 	popq	%rbp
 	popq	%r15
@@ -574,11 +579,6 @@ SYM_CODE_START(trampoline_32bit_src)
 
 	.code32
 0:
-	/* Set up data and stack segments */
-	movl	$__KERNEL_DS, %eax
-	movl	%eax, %ds
-	movl	%eax, %ss
-
 	/* Disable paging */
 	movl	%cr0, %eax
 	btrl	$X86_CR0_PG_BIT, %eax
@@ -633,18 +633,26 @@ SYM_CODE_START(trampoline_32bit_src)
 1:
 	movl	%eax, %cr4
 
-	/* Prepare the stack for far return to Long Mode */
-	pushl	$__KERNEL_CS
-	pushl	%ebx
-
 	/* Enable paging again. */
 	movl	%cr0, %eax
 	btsl	$X86_CR0_PG_BIT, %eax
 	movl	%eax, %cr0
 
-	lret
+	/*
+	 * Return to the 64-bit calling code using LJMP rather than LRET, to
+	 * avoid the need for a 32-bit addressable stack. The destination
+	 * address will be adjusted after the template code is copied into a
+	 * 32-bit addressable buffer.
+	 */
+.Ljmp:	ljmpl	$__KERNEL_CS, $(.Lret - trampoline_32bit_src)
 SYM_CODE_END(trampoline_32bit_src)
 
+/*
+ * This symbol is placed right after trampoline_32bit_src() so its address can
+ * be used to infer the size of the trampoline code.
+ */
+SYM_DATA(trampoline_ljmp_imm_offset, .word  .Ljmp + 1 - trampoline_32bit_src)
+
 	/*
          * The trampoline code has a size limit.
          * Make sure we fail to compile if the trampoline code grows
@@ -652,6 +660,7 @@ SYM_CODE_END(trampoline_32bit_src)
 	 */
 	.org	trampoline_32bit_src + TRAMPOLINE_32BIT_CODE_SIZE
 
+	.text
 SYM_FUNC_START_LOCAL_NOALIGN(.Lno_longmode)
 	/* This isn't an x86-64 CPU, so hang intentionally, we cannot continue */
 1:
arch/x86/boot/compressed/pgtable.h +2 -2
index 4e8cef135226bcbb..c6b0903aded05a07 100644
@@ -8,13 +8,13 @@
 #define TRAMPOLINE_32BIT_CODE_OFFSET	PAGE_SIZE
 #define TRAMPOLINE_32BIT_CODE_SIZE	0xA0
 
-#define TRAMPOLINE_32BIT_STACK_END	TRAMPOLINE_32BIT_SIZE
-
 #ifndef __ASSEMBLER__
 
 extern unsigned long *trampoline_32bit;
 
 extern void trampoline_32bit_src(void *trampoline, bool enable_5lvl);
 
+extern const u16 trampoline_ljmp_imm_offset;
+
 #endif /* __ASSEMBLER__ */
 #endif /* BOOT_COMPRESSED_PAGETABLE_H */
arch/x86/boot/compressed/pgtable_64.c +11 -1
index f8092d3244c9559b..5198a05aefa8d14a 100644
@@ -109,6 +109,7 @@ static unsigned long find_trampoline_placement(void)
 struct paging_config paging_prepare(void *rmode)
 {
 	struct paging_config paging_config = {};
+	void *tramp_code;
 
 	/* Initialize boot_params. Required for cmdline_find_option_bool(). */
 	boot_params = rmode;
@@ -148,9 +149,18 @@ struct paging_config paging_prepare(void *rmode)
 	memset(trampoline_32bit, 0, TRAMPOLINE_32BIT_SIZE);
 
 	/* Copy trampoline code in place */
-	memcpy(trampoline_32bit + TRAMPOLINE_32BIT_CODE_OFFSET / sizeof(unsigned long),
+	tramp_code = memcpy(trampoline_32bit +
+			TRAMPOLINE_32BIT_CODE_OFFSET / sizeof(unsigned long),
 			&trampoline_32bit_src, TRAMPOLINE_32BIT_CODE_SIZE);
 
+	/*
+	 * Avoid the need for a stack in the 32-bit trampoline code, by using
+	 * LJMP rather than LRET to return back to long mode. LJMP takes an
+	 * immediate absolute address, which needs to be adjusted based on the
+	 * placement of the trampoline.
+	 */
+	*(u32 *)(tramp_code + trampoline_ljmp_imm_offset) += (unsigned long)tramp_code;
+
 	/*
 	 * The code below prepares page table in trampoline memory.
 	 *
Signature · 1 line
2.39.2
author maintainer
#12 lore raw

PATCH v8 12/23 x86/decompressor: Call trampoline directly from C code

In reply to Ard Biesheuvel

Instead of returning to the asm calling code to invoke the trampoline, call it straight from the C code that sets it up. That way, the struct return type is no longer needed for returning two values, and the call can be made conditional more cleanly in a subsequent patch.

This means that all callee save 64-bit registers need to be preserved and restored, as their contents may not survive the legacy mode switch.

---
 arch/x86/boot/compressed/head_64.S    | 31 ++++++++-----------
 arch/x86/boot/compressed/pgtable_64.c | 32 ++++++++------------
 2 files changed, 26 insertions(+), 37 deletions(-)
arch/x86/boot/compressed/head_64.S +13 -18
index 37fd7b7d683d696c..cd6e3e175389aa6b 100644
@@ -430,25 +430,14 @@ SYM_CODE_START(startup_64)
 #endif
 
 	/*
-	 * paging_prepare() sets up the trampoline and checks if we need to
-	 * enable 5-level paging.
-	 *
-	 * paging_prepare() returns a two-quadword structure which lands
-	 * into RDX:RAX:
-	 *   - Address of the trampoline is returned in RAX.
-	 *   - Non zero RDX means trampoline needs to enable 5-level
-	 *     paging.
+	 * configure_5level_paging() updates the number of paging levels using
+	 * a trampoline in 32-bit addressable memory if the current number does
+	 * not match the desired number.
 	 *
 	 * Pass the boot_params pointer as the first argument.
 	 */
 	movq	%r15, %rdi
-	call	paging_prepare
-
-	/* Pass the trampoline address and boolean flag as args #1 and #2 */
-	movq	%rax, %rdi
-	movq	%rdx, %rsi
-	leaq	TRAMPOLINE_32BIT_CODE_OFFSET(%rax), %rax
-	call	*%rax
+	call	configure_5level_paging
 
 	/*
 	 * cleanup_trampoline() would restore trampoline memory.
@@ -543,11 +532,14 @@ SYM_FUNC_END(.Lrelocated)
 	.section ".rodata", "a", @progbits
 SYM_CODE_START(trampoline_32bit_src)
 	/*
-	 * Preserve live 64-bit registers on the stack: this is necessary
-	 * because the architecture does not guarantee that GPRs will retain
-	 * their full 64-bit values across a 32-bit mode switch.
+	 * Preserve callee save 64-bit registers on the stack: this is
+	 * necessary because the architecture does not guarantee that GPRs will
+	 * retain their full 64-bit values across a 32-bit mode switch.
 	 */
 	pushq	%r15
+	pushq	%r14
+	pushq	%r13
+	pushq	%r12
 	pushq	%rbp
 	pushq	%rbx
 
@@ -574,6 +566,9 @@ SYM_CODE_START(trampoline_32bit_src)
 	/* Restore the preserved 64-bit registers */
 	popq	%rbx
 	popq	%rbp
+	popq	%r12
+	popq	%r13
+	popq	%r14
 	popq	%r15
 	retq
 
arch/x86/boot/compressed/pgtable_64.c +13 -19
index 5198a05aefa8d14a..f9cc86b2ee55ca80 100644
@@ -16,11 +16,6 @@ unsigned int __section(".data") pgdir_shift = 39;
 unsigned int __section(".data") ptrs_per_p4d = 1;
 #endif
 
-struct paging_config {
-	unsigned long trampoline_start;
-	unsigned long l5_required;
-};
-
 /* Buffer to preserve trampoline memory */
 static char trampoline_save[TRAMPOLINE_32BIT_SIZE];
 
@@ -29,7 +24,7 @@ static char trampoline_save[TRAMPOLINE_32BIT_SIZE];
  * purposes.
  *
  * Avoid putting the pointer into .bss as it will be cleared between
- * paging_prepare() and extract_kernel().
+ * configure_5level_paging() and extract_kernel().
  */
 unsigned long *trampoline_32bit __section(".data");
 
@@ -106,13 +101,13 @@ static unsigned long find_trampoline_placement(void)
 	return bios_start - TRAMPOLINE_32BIT_SIZE;
 }
 
-struct paging_config paging_prepare(void *rmode)
+asmlinkage void configure_5level_paging(struct boot_params *bp)
 {
-	struct paging_config paging_config = {};
-	void *tramp_code;
+	void (*toggle_la57)(void *trampoline, bool enable_5lvl);
+	bool l5_required = false;
 
 	/* Initialize boot_params. Required for cmdline_find_option_bool(). */
-	boot_params = rmode;
+	boot_params = bp;
 
 	/*
 	 * Check if LA57 is desired and supported.
@@ -130,7 +125,7 @@ struct paging_config paging_prepare(void *rmode)
 			!cmdline_find_option_bool("no5lvl") &&
 			native_cpuid_eax(0) >= 7 &&
 			(native_cpuid_ecx(7) & (1 << (X86_FEATURE_LA57 & 31)))) {
-		paging_config.l5_required = 1;
+		l5_required = true;
 
 		/* Initialize variables for 5-level paging */
 		__pgtable_l5_enabled = 1;
@@ -138,9 +133,7 @@ struct paging_config paging_prepare(void *rmode)
 		ptrs_per_p4d = 512;
 	}
 
-	paging_config.trampoline_start = find_trampoline_placement();
-
-	trampoline_32bit = (unsigned long *)paging_config.trampoline_start;
+	trampoline_32bit = (unsigned long *)find_trampoline_placement();
 
 	/* Preserve trampoline memory */
 	memcpy(trampoline_save, trampoline_32bit, TRAMPOLINE_32BIT_SIZE);
@@ -149,7 +142,7 @@ struct paging_config paging_prepare(void *rmode)
 	memset(trampoline_32bit, 0, TRAMPOLINE_32BIT_SIZE);
 
 	/* Copy trampoline code in place */
-	tramp_code = memcpy(trampoline_32bit +
+	toggle_la57 = memcpy(trampoline_32bit +
 			TRAMPOLINE_32BIT_CODE_OFFSET / sizeof(unsigned long),
 			&trampoline_32bit_src, TRAMPOLINE_32BIT_CODE_SIZE);
 
@@ -159,7 +152,8 @@ struct paging_config paging_prepare(void *rmode)
 	 * immediate absolute address, which needs to be adjusted based on the
 	 * placement of the trampoline.
 	 */
-	*(u32 *)(tramp_code + trampoline_ljmp_imm_offset) += (unsigned long)tramp_code;
+	*(u32 *)((u8 *)toggle_la57 + trampoline_ljmp_imm_offset) +=
+						(unsigned long)toggle_la57;
 
 	/*
 	 * The code below prepares page table in trampoline memory.
@@ -175,10 +169,10 @@ struct paging_config paging_prepare(void *rmode)
 	 * We are not going to use the page table in trampoline memory if we
 	 * are already in the desired paging mode.
 	 */
-	if (paging_config.l5_required == !!(native_read_cr4() & X86_CR4_LA57))
+	if (l5_required == !!(native_read_cr4() & X86_CR4_LA57))
 		goto out;
 
-	if (paging_config.l5_required) {
+	if (l5_required) {
 		/*
 		 * For 4- to 5-level paging transition, set up current CR3 as
 		 * the first and the only entry in a new top-level page table.
@@ -201,7 +195,7 @@ struct paging_config paging_prepare(void *rmode)
 	}
 
 out:
-	return paging_config;
+	toggle_la57(trampoline_32bit, l5_required);
 }
 
 void cleanup_trampoline(void *pgtable)
Signature · 1 line
2.39.2
author maintainer
#13 lore raw

PATCH v8 13/23 x86/decompressor: Only call the trampoline when changing paging levels

In reply to Ard Biesheuvel

Since the current and desired number of paging levels are known when the trampoline is being prepared, avoid calling the trampoline at all if it is clear that calling it is not going to result in a change to the number of paging levels.

Given that the CPU is already running in long mode, the PAE and LA57 settings are necessarily consistent with the currently active page tables, and other fields in CR4 will be initialized by the startup code in the kernel proper. So limit the manipulation of CR4 to toggling the LA57 bit, which is the only thing that really needs doing at this point in the boot. This also means that there is no need to pass the value of l5_required to toggle_la57(), as it will not be called unless CR4.LA57 needs to toggle.

---
 arch/x86/boot/compressed/head_64.S    | 45 ++------------------
 arch/x86/boot/compressed/pgtable_64.c | 22 ++++------
 2 files changed, 13 insertions(+), 54 deletions(-)
arch/x86/boot/compressed/head_64.S +4 -41
index cd6e3e175389aa6b..8730b1d58e2b0825 100644
@@ -387,10 +387,6 @@ SYM_CODE_START(startup_64)
 	 * For the trampoline, we need the top page table to reside in lower
 	 * memory as we don't have a way to load 64-bit values into CR3 in
 	 * 32-bit mode.
-	 *
-	 * We go though the trampoline even if we don't have to: if we're
-	 * already in a desired paging mode. This way the trampoline code gets
-	 * tested on every boot.
 	 */
 
 	/* Make sure we have GDT with 32-bit code segment */
@@ -526,8 +522,7 @@ SYM_FUNC_END(.Lrelocated)
  *
  * Return address is at the top of the stack (might be above 4G).
  * The first argument (EDI) contains the 32-bit addressable base of the
- * trampoline memory. A non-zero second argument (ESI) means that the
- * trampoline needs to enable 5-level paging.
+ * trampoline memory.
  */
 	.section ".rodata", "a", @progbits
 SYM_CODE_START(trampoline_32bit_src)
@@ -579,25 +574,10 @@ SYM_CODE_START(trampoline_32bit_src)
 	btrl	$X86_CR0_PG_BIT, %eax
 	movl	%eax, %cr0
 
-	/* Check what paging mode we want to be in after the trampoline */
-	testl	%esi, %esi
-	jz	1f
-
-	/* We want 5-level paging: don't touch CR3 if it already points to 5-level page tables */
-	movl	%cr4, %eax
-	testl	$X86_CR4_LA57, %eax
-	jnz	3f
-	jmp	2f
-1:
-	/* We want 4-level paging: don't touch CR3 if it already points to 4-level page tables */
-	movl	%cr4, %eax
-	testl	$X86_CR4_LA57, %eax
-	jz	3f
-2:
 	/* Point CR3 to the trampoline's new top level page table */
 	leal	TRAMPOLINE_32BIT_PGTABLE_OFFSET(%edi), %eax
 	movl	%eax, %cr3
-3:
+
 	/* Set EFER.LME=1 as a precaution in case hypervsior pulls the rug */
 	movl	$MSR_EFER, %ecx
 	rdmsr
@@ -606,26 +586,9 @@ SYM_CODE_START(trampoline_32bit_src)
 	jc	1f
 	wrmsr
 1:
-#ifdef CONFIG_X86_MCE
-	/*
-	 * Preserve CR4.MCE if the kernel will enable #MC support.
-	 * Clearing MCE may fault in some environments (that also force #MC
-	 * support). Any machine check that occurs before #MC support is fully
-	 * configured will crash the system regardless of the CR4.MCE value set
-	 * here.
-	 */
+	/* Toggle CR4.LA57 */
 	movl	%cr4, %eax
-	andl	$X86_CR4_MCE, %eax
-#else
-	movl	$0, %eax
-#endif
-
-	/* Enable PAE and LA57 (if required) paging modes */
-	orl	$X86_CR4_PAE, %eax
-	testl	%esi, %esi
-	jz	1f
-	orl	$X86_CR4_LA57, %eax
-1:
+	btcl	$X86_CR4_LA57_BIT, %eax
 	movl	%eax, %cr4
 
 	/* Enable paging again. */
arch/x86/boot/compressed/pgtable_64.c +9 -13
index f9cc86b2ee55ca80..4213473ae54883c8 100644
@@ -103,7 +103,7 @@ static unsigned long find_trampoline_placement(void)
 
 asmlinkage void configure_5level_paging(struct boot_params *bp)
 {
-	void (*toggle_la57)(void *trampoline, bool enable_5lvl);
+	void (*toggle_la57)(void *trampoline);
 	bool l5_required = false;
 
 	/* Initialize boot_params. Required for cmdline_find_option_bool(). */
@@ -133,6 +133,13 @@ asmlinkage void configure_5level_paging(struct boot_params *bp)
 		ptrs_per_p4d = 512;
 	}
 
+	/*
+	 * The trampoline will not be used if the paging mode is already set to
+	 * the desired one.
+	 */
+	if (l5_required == !!(native_read_cr4() & X86_CR4_LA57))
+		return;
+
 	trampoline_32bit = (unsigned long *)find_trampoline_placement();
 
 	/* Preserve trampoline memory */
@@ -160,18 +167,8 @@ asmlinkage void configure_5level_paging(struct boot_params *bp)
 	 *
 	 * The new page table will be used by trampoline code for switching
 	 * from 4- to 5-level paging or vice versa.
-	 *
-	 * If switching is not required, the page table is unused: trampoline
-	 * code wouldn't touch CR3.
 	 */
 
-	/*
-	 * We are not going to use the page table in trampoline memory if we
-	 * are already in the desired paging mode.
-	 */
-	if (l5_required == !!(native_read_cr4() & X86_CR4_LA57))
-		goto out;
-
 	if (l5_required) {
 		/*
 		 * For 4- to 5-level paging transition, set up current CR3 as
@@ -194,8 +191,7 @@ asmlinkage void configure_5level_paging(struct boot_params *bp)
 		       (void *)src, PAGE_SIZE);
 	}
 
-out:
-	toggle_la57(trampoline_32bit, l5_required);
+	toggle_la57(trampoline_32bit);
 }
 
 void cleanup_trampoline(void *pgtable)
Signature · 1 line
2.39.2
author maintainer
#14 lore raw

PATCH v8 14/23 x86/decompressor: Pass pgtable address to trampoline directly

In reply to Ard Biesheuvel

The only remaining use of the trampoline address by the trampoline itself is deriving the page table address from it, and this involves adding an offset of 0x0. So simplify this, and pass the new CR3 value directly.

This makes the fact that the page table happens to be at the start of the trampoline allocation an implementation detail of the caller.

---
 arch/x86/boot/compressed/head_64.S    | 8 ++++----
 arch/x86/boot/compressed/pgtable.h    | 2 --
 arch/x86/boot/compressed/pgtable_64.c | 9 ++++-----
 3 files changed, 8 insertions(+), 11 deletions(-)
arch/x86/boot/compressed/head_64.S +4 -4
index 8730b1d58e2b0825..afdaf8cb8bb98694 100644
@@ -521,8 +521,9 @@ SYM_FUNC_END(.Lrelocated)
  * running in 64-bit mode.
  *
  * Return address is at the top of the stack (might be above 4G).
- * The first argument (EDI) contains the 32-bit addressable base of the
- * trampoline memory.
+ * The first argument (EDI) contains the address of the temporary PGD level
+ * page table in 32-bit addressable memory which will be programmed into
+ * register CR3.
  */
 	.section ".rodata", "a", @progbits
 SYM_CODE_START(trampoline_32bit_src)
@@ -575,8 +576,7 @@ SYM_CODE_START(trampoline_32bit_src)
 	movl	%eax, %cr0
 
 	/* Point CR3 to the trampoline's new top level page table */
-	leal	TRAMPOLINE_32BIT_PGTABLE_OFFSET(%edi), %eax
-	movl	%eax, %cr3
+	movl	%edi, %cr3
 
 	/* Set EFER.LME=1 as a precaution in case hypervsior pulls the rug */
 	movl	$MSR_EFER, %ecx
arch/x86/boot/compressed/pgtable.h +0 -2
index c6b0903aded05a07..6d595abe06b34d63 100644
@@ -3,8 +3,6 @@
 
 #define TRAMPOLINE_32BIT_SIZE		(2 * PAGE_SIZE)
 
-#define TRAMPOLINE_32BIT_PGTABLE_OFFSET	0
-
 #define TRAMPOLINE_32BIT_CODE_OFFSET	PAGE_SIZE
 #define TRAMPOLINE_32BIT_CODE_SIZE	0xA0
 
arch/x86/boot/compressed/pgtable_64.c +4 -5
index 4213473ae54883c8..eab4e6b568ae05c4 100644
@@ -103,7 +103,7 @@ static unsigned long find_trampoline_placement(void)
 
 asmlinkage void configure_5level_paging(struct boot_params *bp)
 {
-	void (*toggle_la57)(void *trampoline);
+	void (*toggle_la57)(void *cr3);
 	bool l5_required = false;
 
 	/* Initialize boot_params. Required for cmdline_find_option_bool(). */
@@ -174,7 +174,7 @@ asmlinkage void configure_5level_paging(struct boot_params *bp)
 		 * For 4- to 5-level paging transition, set up current CR3 as
 		 * the first and the only entry in a new top-level page table.
 		 */
-		trampoline_32bit[TRAMPOLINE_32BIT_PGTABLE_OFFSET] = __native_read_cr3() | _PAGE_TABLE_NOENC;
+		*trampoline_32bit = __native_read_cr3() | _PAGE_TABLE_NOENC;
 	} else {
 		unsigned long src;
 
@@ -187,8 +187,7 @@ asmlinkage void configure_5level_paging(struct boot_params *bp)
 		 * may be above 4G.
 		 */
 		src = *(unsigned long *)__native_read_cr3() & PAGE_MASK;
-		memcpy(trampoline_32bit + TRAMPOLINE_32BIT_PGTABLE_OFFSET / sizeof(unsigned long),
-		       (void *)src, PAGE_SIZE);
+		memcpy(trampoline_32bit, (void *)src, PAGE_SIZE);
 	}
 
 	toggle_la57(trampoline_32bit);
@@ -198,7 +197,7 @@ void cleanup_trampoline(void *pgtable)
 {
 	void *trampoline_pgtable;
 
-	trampoline_pgtable = trampoline_32bit + TRAMPOLINE_32BIT_PGTABLE_OFFSET / sizeof(unsigned long);
+	trampoline_pgtable = trampoline_32bit;
 
 	/*
 	 * Move the top level page table out of trampoline memory,
Signature · 1 line
2.39.2
author maintainer
#15 lore raw

PATCH v8 15/23 x86/decompressor: Merge trampoline cleanup with switching code

In reply to Ard Biesheuvel

Now that the trampoline setup code and the actual invocation of it are all done from the C routine, the trampoline cleanup can be merged into it as well, instead of returning to asm just to call another C function.

---
 arch/x86/boot/compressed/head_64.S    | 14 ++++----------
 arch/x86/boot/compressed/pgtable_64.c | 18 ++++--------------
 2 files changed, 8 insertions(+), 24 deletions(-)
arch/x86/boot/compressed/head_64.S +4 -10
index afdaf8cb8bb98694..fb0e562c26f64c9c 100644
@@ -430,20 +430,14 @@ SYM_CODE_START(startup_64)
 	 * a trampoline in 32-bit addressable memory if the current number does
 	 * not match the desired number.
 	 *
-	 * Pass the boot_params pointer as the first argument.
+	 * Pass the boot_params pointer as the first argument. The second
+	 * argument is the relocated address of the page table to use instead
+	 * of the page table in trampoline memory (if required).
 	 */
 	movq	%r15, %rdi
+	leaq	rva(top_pgtable)(%rbx), %rsi
 	call	configure_5level_paging
 
-	/*
-	 * cleanup_trampoline() would restore trampoline memory.
-	 *
-	 * RDI is address of the page table to use instead of page table
-	 * in trampoline memory (if required).
-	 */
-	leaq	rva(top_pgtable)(%rbx), %rdi
-	call	cleanup_trampoline
-
 	/* Zero EFLAGS */
 	pushq	$0
 	popfq
arch/x86/boot/compressed/pgtable_64.c +4 -14
index eab4e6b568ae05c4..7939eb6e6ce9bb01 100644
@@ -101,7 +101,7 @@ static unsigned long find_trampoline_placement(void)
 	return bios_start - TRAMPOLINE_32BIT_SIZE;
 }
 
-asmlinkage void configure_5level_paging(struct boot_params *bp)
+asmlinkage void configure_5level_paging(struct boot_params *bp, void *pgtable)
 {
 	void (*toggle_la57)(void *cr3);
 	bool l5_required = false;
@@ -191,22 +191,12 @@ asmlinkage void configure_5level_paging(struct boot_params *bp)
 	}
 
 	toggle_la57(trampoline_32bit);
-}
-
-void cleanup_trampoline(void *pgtable)
-{
-	void *trampoline_pgtable;
-
-	trampoline_pgtable = trampoline_32bit;
 
 	/*
-	 * Move the top level page table out of trampoline memory,
-	 * if it's there.
+	 * Move the top level page table out of trampoline memory.
 	 */
-	if ((void *)__native_read_cr3() == trampoline_pgtable) {
-		memcpy(pgtable, trampoline_pgtable, PAGE_SIZE);
-		native_write_cr3((unsigned long)pgtable);
-	}
+	memcpy(pgtable, trampoline_32bit, PAGE_SIZE);
+	native_write_cr3((unsigned long)pgtable);
 
 	/* Restore trampoline memory */
 	memcpy(trampoline_32bit, trampoline_save, TRAMPOLINE_32BIT_SIZE);
Signature · 1 line
2.39.2
author maintainer
#16 lore raw

PATCH v8 16/23 x86/efistub: Perform 4/5 level paging switch from the stub

In reply to Ard Biesheuvel

In preparation for updating the EFI stub boot flow to avoid the bare metal decompressor code altogether, implement the support code for switching between 4 and 5 levels of paging before jumping to the kernel proper.

This reuses the newly refactored trampoline that the bare metal decompressor uses, but relies on EFI APIs to allocate 32-bit addressable memory and remap it with the appropriate permissions. Given that the bare metal decompressor will no longer call into the trampoline if the number of paging levels is already set correctly, it is no longer needed to remove NX restrictions from the memory range where this trampoline may end up.

---
 drivers/firmware/efi/libstub/Makefile          |  1 +
 drivers/firmware/efi/libstub/efi-stub-helper.c |  2 +
 drivers/firmware/efi/libstub/efistub.h         |  1 +
 drivers/firmware/efi/libstub/x86-5lvl.c        | 95 ++++++++++++++++++++
 drivers/firmware/efi/libstub/x86-stub.c        | 40 +++------
 drivers/firmware/efi/libstub/x86-stub.h        | 17 ++++
 6 files changed, 130 insertions(+), 26 deletions(-)
drivers/firmware/efi/libstub/Makefile +1 -0
index 16d64a34d1e19465..ae8874401a9f1490 100644
@@ -88,6 +88,7 @@ lib-$(CONFIG_EFI_GENERIC_STUB)	+= efi-stub.o string.o intrinsics.o systable.o \
 lib-$(CONFIG_ARM)		+= arm32-stub.o
 lib-$(CONFIG_ARM64)		+= arm64.o arm64-stub.o smbios.o
 lib-$(CONFIG_X86)		+= x86-stub.o
+lib-$(CONFIG_X86_64)		+= x86-5lvl.o
 lib-$(CONFIG_RISCV)		+= riscv.o riscv-stub.o
 lib-$(CONFIG_LOONGARCH)		+= loongarch.o loongarch-stub.o
 
drivers/firmware/efi/libstub/efi-stub-helper.c +2 -0
index 732984295295fb6d..bfa30625f5d03167 100644
@@ -73,6 +73,8 @@ efi_status_t efi_parse_options(char const *cmdline)
 			efi_loglevel = CONSOLE_LOGLEVEL_QUIET;
 		} else if (!strcmp(param, "noinitrd")) {
 			efi_noinitrd = true;
+		} else if (IS_ENABLED(CONFIG_X86_64) && !strcmp(param, "no5lvl")) {
+			efi_no5lvl = true;
 		} else if (!strcmp(param, "efi") && val) {
 			efi_nochunk = parse_option_str(val, "nochunk");
 			efi_novamap |= parse_option_str(val, "novamap");
drivers/firmware/efi/libstub/efistub.h +1 -0
index 6aa38a1bf1265d83..06b7abc92ced9e18 100644
@@ -33,6 +33,7 @@
 #define EFI_ALLOC_LIMIT		ULONG_MAX
 #endif
 
+extern bool efi_no5lvl;
 extern bool efi_nochunk;
 extern bool efi_nokaslr;
 extern int efi_loglevel;
drivers/firmware/efi/libstub/x86-5lvl.c new file +95 -0

95 lines not on this page · raw message

drivers/firmware/efi/libstub/x86-stub.c +14 -26
index 9247dbc7dbbd12ef..af5f50617a5b4c59 100644
@@ -17,6 +17,7 @@
 #include <asm/boot.h>
 
 #include "efistub.h"
+#include "x86-stub.h"
 
 /* Maximum physical address for 64-bit kernel with 4-level paging */
 #define MAXMEM_X86_64_4LEVEL (1ull << 46)
@@ -223,8 +224,8 @@ static void retrieve_apple_device_properties(struct boot_params *boot_params)
 	}
 }
 
-static void
-adjust_memory_range_protection(unsigned long start, unsigned long size)
+void efi_adjust_memory_range_protection(unsigned long start,
+					unsigned long size)
 {
 	efi_status_t status;
 	efi_gcd_memory_space_desc_t desc;
@@ -278,35 +279,14 @@ adjust_memory_range_protection(unsigned long start, unsigned long size)
 	}
 }
 
-/*
- * Trampoline takes 2 pages and can be loaded in first megabyte of memory
- * with its end placed between 128k and 640k where BIOS might start.
- * (see arch/x86/boot/compressed/pgtable_64.c)
- *
- * We cannot find exact trampoline placement since memory map
- * can be modified by UEFI, and it can alter the computed address.
- */
-
-#define TRAMPOLINE_PLACEMENT_BASE ((128 - 8)*1024)
-#define TRAMPOLINE_PLACEMENT_SIZE (640*1024 - (128 - 8)*1024)
-
 extern const u8 startup_32[], startup_64[];
 
 static void
 setup_memory_protection(unsigned long image_base, unsigned long image_size)
 {
-	/*
-	 * Allow execution of possible trampoline used
-	 * for switching between 4- and 5-level page tables
-	 * and relocated kernel image.
-	 */
-
-	adjust_memory_range_protection(TRAMPOLINE_PLACEMENT_BASE,
-				       TRAMPOLINE_PLACEMENT_SIZE);
-
 #ifdef CONFIG_64BIT
 	if (image_base != (unsigned long)startup_32)
-		adjust_memory_range_protection(image_base, image_size);
+		efi_adjust_memory_range_protection(image_base, image_size);
 #else
 	/*
 	 * Clear protection flags on a whole range of possible
@@ -316,8 +296,8 @@ setup_memory_protection(unsigned long image_base, unsigned long image_size)
 	 * need to remove possible protection on relocated image
 	 * itself disregarding further relocations.
 	 */
-	adjust_memory_range_protection(LOAD_PHYSICAL_ADDR,
-				       KERNEL_IMAGE_SIZE - LOAD_PHYSICAL_ADDR);
+	efi_adjust_memory_range_protection(LOAD_PHYSICAL_ADDR,
+					   KERNEL_IMAGE_SIZE - LOAD_PHYSICAL_ADDR);
 #endif
 }
 
@@ -839,6 +819,12 @@ void __noreturn efi_stub_entry(efi_handle_t handle,
 		efi_dxe_table = NULL;
 	}
 
+	status = efi_setup_5level_paging();
+	if (status != EFI_SUCCESS) {
+		efi_err("efi_setup_5level_paging() failed!\n");
+		goto fail;
+	}
+
 	/*
 	 * If the kernel isn't already loaded at a suitable address,
 	 * relocate it.
@@ -959,6 +945,8 @@ void __noreturn efi_stub_entry(efi_handle_t handle,
 		goto fail;
 	}
 
+	efi_5level_switch();
+
 	if (IS_ENABLED(CONFIG_X86_64))
 		bzimage_addr += startup_64 - startup_32;
 
drivers/firmware/efi/libstub/x86-stub.h new file +17 -0
new file mode 100644
index 0000000000000000..37c5a36b9d8cf9b2
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#include <linux/efi.h>
+
+extern void trampoline_32bit_src(void *, bool);
+extern const u16 trampoline_ljmp_imm_offset;
+
+void efi_adjust_memory_range_protection(unsigned long start,
+					unsigned long size);
+
+#ifdef CONFIG_X86_64
+efi_status_t efi_setup_5level_paging(void);
+void efi_5level_switch(void);
+#else
+static inline efi_status_t efi_setup_5level_paging(void) { return EFI_SUCCESS; }
+static inline void efi_5level_switch(void) {}
+#endif
Signature · 1 line
2.39.2
author maintainer
#17 lore raw

PATCH v8 17/23 x86/efistub: Prefer EFI memory attributes protocol over DXE services

In reply to Ard Biesheuvel

Currently, the EFI stub relies on DXE services in some cases to clear non-execute restrictions from page allocations that need to be executable. This is dodgy, because DXE services are not specified by UEFI but by PI, and they are not intended for consumption by OS loaders. However, no alternative existed at the time.

Now, there is a new UEFI protocol that should be used instead, so if it exists, prefer it over the DXE services calls.

---
 drivers/firmware/efi/libstub/x86-stub.c | 29 ++++++++++++++------
 1 file changed, 21 insertions(+), 8 deletions(-)
drivers/firmware/efi/libstub/x86-stub.c +21 -8
index af5f50617a5b4c59..acb1c65bf8ac6fb3 100644
@@ -26,6 +26,7 @@ const efi_system_table_t *efi_system_table;
 const efi_dxe_services_table_t *efi_dxe_table;
 u32 image_offset __section(".data");
 static efi_loaded_image_t *image = NULL;
+static efi_memory_attribute_protocol_t *memattr;
 
 typedef union sev_memory_acceptance_protocol sev_memory_acceptance_protocol_t;
 union sev_memory_acceptance_protocol {
@@ -233,12 +234,18 @@ void efi_adjust_memory_range_protection(unsigned long start,
 	unsigned long rounded_start, rounded_end;
 	unsigned long unprotect_start, unprotect_size;
 
-	if (efi_dxe_table == NULL)
-		return;
-
 	rounded_start = rounddown(start, EFI_PAGE_SIZE);
 	rounded_end = roundup(start + size, EFI_PAGE_SIZE);
 
+	if (memattr != NULL) {
+		efi_call_proto(memattr, clear_memory_attributes, rounded_start,
+			       rounded_end - rounded_start, EFI_MEMORY_XP);
+		return;
+	}
+
+	if (efi_dxe_table == NULL)
+		return;
+
 	/*
 	 * Don't modify memory region attributes, they are
 	 * already suitable, to lower the possibility to
@@ -801,6 +808,7 @@ void __noreturn efi_stub_entry(efi_handle_t handle,
 			       efi_system_table_t *sys_table_arg,
 			       struct boot_params *boot_params)
 {
+	efi_guid_t guid = EFI_MEMORY_ATTRIBUTE_PROTOCOL_GUID;
 	unsigned long bzimage_addr = (unsigned long)startup_32;
 	unsigned long buffer_start, buffer_end;
 	struct setup_header *hdr = &boot_params->hdr;
@@ -812,13 +820,18 @@ void __noreturn efi_stub_entry(efi_handle_t handle,
 	if (efi_system_table->hdr.signature != EFI_SYSTEM_TABLE_SIGNATURE)
 		efi_exit(handle, EFI_INVALID_PARAMETER);
 
-	efi_dxe_table = get_efi_config_table(EFI_DXE_SERVICES_TABLE_GUID);
-	if (efi_dxe_table &&
-	    efi_dxe_table->hdr.signature != EFI_DXE_SERVICES_TABLE_SIGNATURE) {
-		efi_warn("Ignoring DXE services table: invalid signature\n");
-		efi_dxe_table = NULL;
+	if (IS_ENABLED(CONFIG_EFI_DXE_MEM_ATTRIBUTES)) {
+		efi_dxe_table = get_efi_config_table(EFI_DXE_SERVICES_TABLE_GUID);
+		if (efi_dxe_table &&
+		    efi_dxe_table->hdr.signature != EFI_DXE_SERVICES_TABLE_SIGNATURE) {
+			efi_warn("Ignoring DXE services table: invalid signature\n");
+			efi_dxe_table = NULL;
+		}
 	}
 
+	/* grab the memory attributes protocol if it exists */
+	efi_bs_call(locate_protocol, &guid, NULL, (void **)&memattr);
+
 	status = efi_setup_5level_paging();
 	if (status != EFI_SUCCESS) {
 		efi_err("efi_setup_5level_paging() failed!\n");
Signature · 1 line
2.39.2
author maintainer
#18 lore raw

PATCH v8 18/23 decompress: Use 8 byte alignment

In reply to Ard Biesheuvel

The ZSTD decompressor requires malloc() allocations to be 8 byte aligned, so ensure that this the case.

---
 include/linux/decompress/mm.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/linux/decompress/mm.h +1 -1
index 9192986b1a731323..ac862422df158bef 100644
@@ -48,7 +48,7 @@ MALLOC_VISIBLE void *malloc(int size)
 	if (!malloc_ptr)
 		malloc_ptr = free_mem_ptr;
 
-	malloc_ptr = (malloc_ptr + 3) & ~3;     /* Align */
+	malloc_ptr = (malloc_ptr + 7) & ~7;     /* Align */
 
 	p = (void *)malloc_ptr;
 	malloc_ptr += size;
Signature · 1 line
2.39.2
author maintainer
#19 lore raw

PATCH v8 19/23 x86/decompressor: Move global symbol references to C code

In reply to Ard Biesheuvel

It is no longer necessary to be cautious when referring to global variables in the position independent decompressor code, now that it is built using PIE codegen and makes an assertion in the linker script that no GOT entries exist (which would require adjustment for the actual runtime load address of the decompressor binary).

This means global variables can be referenced directly from C code, instead of having to pass their runtime addresses into C routines from asm code, which needs to happen at each call site. Do so for the code that will be called directly from the EFI stub after a subsequent patch, and avoid the need to duplicate this logic a third time.

---
 arch/x86/boot/compressed/head_32.S |  8 --------
 arch/x86/boot/compressed/head_64.S | 10 ++--------
 arch/x86/boot/compressed/misc.c    | 16 +++++++++-------
 3 files changed, 11 insertions(+), 23 deletions(-)
arch/x86/boot/compressed/head_32.S +0 -8
index 8876ffe30e9a4819..3af4a383615b3e1f 100644
@@ -168,13 +168,7 @@ SYM_FUNC_START_LOCAL_NOALIGN(.Lrelocated)
  */
 	/* push arguments for extract_kernel: */
 
-	pushl	output_len@GOTOFF(%ebx)	/* decompressed length, end of relocs */
 	pushl	%ebp			/* output address */
-	pushl	input_len@GOTOFF(%ebx)	/* input_len */
-	leal	input_data@GOTOFF(%ebx), %eax
-	pushl	%eax			/* input_data */
-	leal	boot_heap@GOTOFF(%ebx), %eax
-	pushl	%eax			/* heap area */
 	pushl	%esi			/* real mode pointer */
 	call	extract_kernel		/* returns kernel entry point in %eax */
 	addl	$24, %esp
@@ -202,8 +196,6 @@ SYM_DATA_END_LABEL(gdt, SYM_L_LOCAL, gdt_end)
  */
 	.bss
 	.balign 4
-boot_heap:
-	.fill BOOT_HEAP_SIZE, 1, 0
 boot_stack:
 	.fill BOOT_STACK_SIZE, 1, 0
 boot_stack_end:
arch/x86/boot/compressed/head_64.S +2 -8
index fb0e562c26f64c9c..28f46051c706724e 100644
@@ -493,13 +493,9 @@ SYM_FUNC_START_LOCAL_NOALIGN(.Lrelocated)
 /*
  * Do the extraction, and jump to the new kernel..
  */
-	/* pass struct boot_params pointer */
+	/* pass struct boot_params pointer and output target address */
 	movq	%r15, %rdi
-	leaq	boot_heap(%rip), %rsi	/* malloc area for uncompression */
-	leaq	input_data(%rip), %rdx  /* input_data */
-	movl	input_len(%rip), %ecx	/* input_len */
-	movq	%rbp, %r8		/* output target address */
-	movl	output_len(%rip), %r9d	/* decompressed length, end of relocs */
+	movq	%rbp, %rsi
 	call	extract_kernel		/* returns kernel entry point in %rax */
 
 /*
@@ -657,8 +653,6 @@ SYM_DATA_END_LABEL(boot_idt, SYM_L_GLOBAL, boot_idt_end)
  */
 	.bss
 	.balign 4
-SYM_DATA_LOCAL(boot_heap,	.fill BOOT_HEAP_SIZE, 1, 0)
-
 SYM_DATA_START_LOCAL(boot_stack)
 	.fill BOOT_STACK_SIZE, 1, 0
 	.balign 16
arch/x86/boot/compressed/misc.c +9 -7
index 94b7abcf624b3b55..2d91d56b59e1af93 100644
@@ -330,6 +330,11 @@ static size_t parse_elf(void *output)
 	return ehdr.e_entry - LOAD_PHYSICAL_ADDR;
 }
 
+static u8 boot_heap[BOOT_HEAP_SIZE] __aligned(4);
+
+extern unsigned char input_data[];
+extern unsigned int input_len, output_len;
+
 /*
  * The compressed kernel image (ZO), has been moved so that its position
  * is against the end of the buffer used to hold the uncompressed kernel
@@ -347,14 +352,11 @@ static size_t parse_elf(void *output)
  *             |-------uncompressed kernel image---------|
  *
  */
-asmlinkage __visible void *extract_kernel(void *rmode, memptr heap,
-				  unsigned char *input_data,
-				  unsigned long input_len,
-				  unsigned char *output,
-				  unsigned long output_len)
+asmlinkage __visible void *extract_kernel(void *rmode, unsigned char *output)
 {
 	const unsigned long kernel_total_size = VO__end - VO__text;
 	unsigned long virt_addr = LOAD_PHYSICAL_ADDR;
+	memptr heap = (memptr)boot_heap;
 	unsigned long needed_size;
 	size_t entry_offset;
 
@@ -412,7 +414,7 @@ asmlinkage __visible void *extract_kernel(void *rmode, memptr heap,
 	 * entries. This ensures the full mapped area is usable RAM
 	 * and doesn't include any reserved areas.
 	 */
-	needed_size = max(output_len, kernel_total_size);
+	needed_size = max_t(unsigned long, output_len, kernel_total_size);
 #ifdef CONFIG_X86_64
 	needed_size = ALIGN(needed_size, MIN_KERNEL_ALIGN);
 #endif
@@ -443,7 +445,7 @@ asmlinkage __visible void *extract_kernel(void *rmode, memptr heap,
 #ifdef CONFIG_X86_64
 	if (heap > 0x3fffffffffffUL)
 		error("Destination address too large");
-	if (virt_addr + max(output_len, kernel_total_size) > KERNEL_IMAGE_SIZE)
+	if (virt_addr + needed_size > KERNEL_IMAGE_SIZE)
 		error("Destination virtual address is beyond the kernel mapping area");
 #else
 	if (heap > ((-__PAGE_OFFSET-(128<<20)-1) & 0x7fffffff))
Signature · 1 line
2.39.2
author maintainer
#20 lore raw

PATCH v8 20/23 x86/decompressor: Factor out kernel decompression and relocation

In reply to Ard Biesheuvel

Factor out the decompressor sequence that invokes the decompressor, parses the ELF and applies the relocations so that it can be called directly from the EFI stub.

---
 arch/x86/boot/compressed/misc.c | 28 ++++++++++++++++----
 arch/x86/include/asm/boot.h     |  8 ++++++
 2 files changed, 31 insertions(+), 5 deletions(-)
arch/x86/boot/compressed/misc.c +23 -5
index 2d91d56b59e1af93..f711f2a85862e9ef 100644
@@ -330,11 +330,33 @@ static size_t parse_elf(void *output)
 	return ehdr.e_entry - LOAD_PHYSICAL_ADDR;
 }
 
+const unsigned long kernel_total_size = VO__end - VO__text;
+
 static u8 boot_heap[BOOT_HEAP_SIZE] __aligned(4);
 
 extern unsigned char input_data[];
 extern unsigned int input_len, output_len;
 
+unsigned long decompress_kernel(unsigned char *outbuf, unsigned long virt_addr,
+				void (*error)(char *x))
+{
+	unsigned long entry;
+
+	if (!free_mem_ptr) {
+		free_mem_ptr     = (unsigned long)boot_heap;
+		free_mem_end_ptr = (unsigned long)boot_heap + sizeof(boot_heap);
+	}
+
+	if (__decompress(input_data, input_len, NULL, NULL, outbuf, output_len,
+			 NULL, error) < 0)
+		return ULONG_MAX;
+
+	entry = parse_elf(outbuf);
+	handle_relocations(outbuf, output_len, virt_addr);
+
+	return entry;
+}
+
 /*
  * The compressed kernel image (ZO), has been moved so that its position
  * is against the end of the buffer used to hold the uncompressed kernel
@@ -354,7 +376,6 @@ extern unsigned int input_len, output_len;
  */
 asmlinkage __visible void *extract_kernel(void *rmode, unsigned char *output)
 {
-	const unsigned long kernel_total_size = VO__end - VO__text;
 	unsigned long virt_addr = LOAD_PHYSICAL_ADDR;
 	memptr heap = (memptr)boot_heap;
 	unsigned long needed_size;
@@ -463,10 +484,7 @@ asmlinkage __visible void *extract_kernel(void *rmode, unsigned char *output)
 		accept_memory(__pa(output), __pa(output) + needed_size);
 	}
 
-	__decompress(input_data, input_len, NULL, NULL, output, output_len,
-			NULL, error);
-	entry_offset = parse_elf(output);
-	handle_relocations(output, output_len, virt_addr);
+	entry_offset = decompress_kernel(output, virt_addr, error);
 
 	debug_putstr("done.\nBooting the kernel (entry_offset: 0x");
 	debug_puthex(entry_offset);
arch/x86/include/asm/boot.h +8 -0
index 9191280d9ea3160d..4ae14339cb8cc72d 100644
@@ -62,4 +62,12 @@
 # define BOOT_STACK_SIZE	0x1000
 #endif
 
+#ifndef __ASSEMBLY__
+extern unsigned int output_len;
+extern const unsigned long kernel_total_size;
+
+unsigned long decompress_kernel(unsigned char *outbuf, unsigned long virt_addr,
+				void (*error)(char *x));
+#endif
+
 #endif /* _ASM_X86_BOOT_H */
Signature · 1 line
2.39.2
author maintainer
#21 lore raw

PATCH v8 21/23 efi/libstub: Add limit argument to efi_random_alloc()

In reply to Ard Biesheuvel

x86 will need to limit the kernel memory allocation to the lowest 512 MiB of memory, to match the behavior of the existing bare metal KASLR physical randomization logic. So in preparation for that, add a limit parameter to efi_random_alloc() and wire it up.

---
 drivers/firmware/efi/libstub/arm64-stub.c  |  2 +-
 drivers/firmware/efi/libstub/efistub.h     |  2 +-
 drivers/firmware/efi/libstub/randomalloc.c | 10 ++++++----
 drivers/firmware/efi/libstub/zboot.c       |  2 +-
 4 files changed, 9 insertions(+), 7 deletions(-)
drivers/firmware/efi/libstub/arm64-stub.c +1 -1
index 770b8ecb73984c61..8c40fc89f5f99209 100644
@@ -106,7 +106,7 @@ efi_status_t handle_kernel_image(unsigned long *image_addr,
 		 */
 		status = efi_random_alloc(*reserve_size, min_kimg_align,
 					  reserve_addr, phys_seed,
-					  EFI_LOADER_CODE);
+					  EFI_LOADER_CODE, EFI_ALLOC_LIMIT);
 		if (status != EFI_SUCCESS)
 			efi_warn("efi_random_alloc() failed: 0x%lx\n", status);
 	} else {
drivers/firmware/efi/libstub/efistub.h +1 -1
index 06b7abc92ced9e18..9823f6fb3e01f718 100644
@@ -956,7 +956,7 @@ efi_status_t efi_get_random_bytes(unsigned long size, u8 *out);
 
 efi_status_t efi_random_alloc(unsigned long size, unsigned long align,
 			      unsigned long *addr, unsigned long random_seed,
-			      int memory_type);
+			      int memory_type, unsigned long alloc_limit);
 
 efi_status_t efi_random_get_seed(void);
 
drivers/firmware/efi/libstub/randomalloc.c +6 -4
index 32c7a54923b4c127..674a064b8f7adc68 100644
@@ -16,7 +16,8 @@
  */
 static unsigned long get_entry_num_slots(efi_memory_desc_t *md,
 					 unsigned long size,
-					 unsigned long align_shift)
+					 unsigned long align_shift,
+					 u64 alloc_limit)
 {
 	unsigned long align = 1UL << align_shift;
 	u64 first_slot, last_slot, region_end;
@@ -29,7 +30,7 @@ static unsigned long get_entry_num_slots(efi_memory_desc_t *md,
 		return 0;
 
 	region_end = min(md->phys_addr + md->num_pages * EFI_PAGE_SIZE - 1,
-			 (u64)EFI_ALLOC_LIMIT);
+			 alloc_limit);
 	if (region_end < size)
 		return 0;
 
@@ -54,7 +55,8 @@ efi_status_t efi_random_alloc(unsigned long size,
 			      unsigned long align,
 			      unsigned long *addr,
 			      unsigned long random_seed,
-			      int memory_type)
+			      int memory_type,
+			      unsigned long alloc_limit)
 {
 	unsigned long total_slots = 0, target_slot;
 	unsigned long total_mirrored_slots = 0;
@@ -76,7 +78,7 @@ efi_status_t efi_random_alloc(unsigned long size,
 		efi_memory_desc_t *md = (void *)map->map + map_offset;
 		unsigned long slots;
 
-		slots = get_entry_num_slots(md, size, ilog2(align));
+		slots = get_entry_num_slots(md, size, ilog2(align), alloc_limit);
 		MD_NUM_SLOTS(md) = slots;
 		total_slots += slots;
 		if (md->attribute & EFI_MEMORY_MORE_RELIABLE)
drivers/firmware/efi/libstub/zboot.c +1 -1
index e5d7fa1f1d8fd160..bdb17eac0cb401be 100644
@@ -119,7 +119,7 @@ efi_zboot_entry(efi_handle_t handle, efi_system_table_t *systab)
 		}
 
 		status = efi_random_alloc(alloc_size, min_kimg_align, &image_base,
-					  seed, EFI_LOADER_CODE);
+					  seed, EFI_LOADER_CODE, EFI_ALLOC_LIMIT);
 		if (status != EFI_SUCCESS) {
 			efi_err("Failed to allocate memory\n");
 			goto free_cmdline;
Signature · 1 line
2.39.2
author maintainer
#22 lore raw

PATCH v8 22/23 x86/efistub: Perform SNP feature test while running in the firmware

In reply to Ard Biesheuvel

Before refactoring the EFI stub boot flow to avoid the legacy bare metal decompressor, duplicate the SNP feature check in the EFI stub before handing over to the kernel proper.

The SNP feature check can be performed while running under the EFI boot services, which means it can force the boot to fail gracefully and return an error to the bootloader if the loaded kernel does not implement support for all the features that the hypervisor enabled.

---
 arch/x86/boot/compressed/sev.c          | 112 ++++++++++++--------
 arch/x86/include/asm/sev.h              |   4 +
 drivers/firmware/efi/libstub/x86-stub.c |  17 +++
 3 files changed, 87 insertions(+), 46 deletions(-)
arch/x86/boot/compressed/sev.c +66 -46
index c3e343bd4760e0ab..199155b8af3bc535 100644
@@ -367,20 +367,25 @@ static void enforce_vmpl0(void)
  */
 #define SNP_FEATURES_PRESENT (0)
 
+u64 snp_get_unsupported_features(u64 status)
+{
+	if (!(status & MSR_AMD64_SEV_SNP_ENABLED))
+		return 0;
+
+	return status & SNP_FEATURES_IMPL_REQ & ~SNP_FEATURES_PRESENT;
+}
+
 void snp_check_features(void)
 {
 	u64 unsupported;
 
-	if (!(sev_status & MSR_AMD64_SEV_SNP_ENABLED))
-		return;
-
 	/*
 	 * Terminate the boot if hypervisor has enabled any feature lacking
 	 * guest side implementation. Pass on the unsupported features mask through
 	 * EXIT_INFO_2 of the GHCB protocol so that those features can be reported
 	 * as part of the guest boot failure.
 	 */
-	unsupported = sev_status & SNP_FEATURES_IMPL_REQ & ~SNP_FEATURES_PRESENT;
+	unsupported = snp_get_unsupported_features(sev_status);
 	if (unsupported) {
 		if (ghcb_version < 2 || (!boot_ghcb && !early_setup_ghcb()))
 			sev_es_terminate(SEV_TERM_SET_GEN, GHCB_SNP_UNSUPPORTED);
@@ -390,10 +395,45 @@ void snp_check_features(void)
 	}
 }
 
-void sev_enable(struct boot_params *bp)
+/*
+ * sev_check_cpu_support - Check for SEV support in the CPU capabilities
+ *
+ * Returns < 0 if SEV is not supported, otherwise the position of the
+ * encryption bit in the page table descriptors.
+ */
+static int sev_check_cpu_support(void)
 {
 	unsigned int eax, ebx, ecx, edx;
+
+	/* Check for the SME/SEV support leaf */
+	eax = 0x80000000;
+	ecx = 0;
+	native_cpuid(&eax, &ebx, &ecx, &edx);
+	if (eax < 0x8000001f)
+		return -ENODEV;
+
+	/*
+	 * Check for the SME/SEV feature:
+	 *   CPUID Fn8000_001F[EAX]
+	 *   - Bit 0 - Secure Memory Encryption support
+	 *   - Bit 1 - Secure Encrypted Virtualization support
+	 *   CPUID Fn8000_001F[EBX]
+	 *   - Bits 5:0 - Pagetable bit position used to indicate encryption
+	 */
+	eax = 0x8000001f;
+	ecx = 0;
+	native_cpuid(&eax, &ebx, &ecx, &edx);
+	/* Check whether SEV is supported */
+	if (!(eax & BIT(1)))
+		return -ENODEV;
+
+	return ebx & 0x3f;
+}
+
+void sev_enable(struct boot_params *bp)
+{
 	struct msr m;
+	int bitpos;
 	bool snp;
 
 	/*
@@ -413,26 +453,7 @@ void sev_enable(struct boot_params *bp)
 	 * which is good enough.
 	 */
 
-	/* Check for the SME/SEV support leaf */
-	eax = 0x80000000;
-	ecx = 0;
-	native_cpuid(&eax, &ebx, &ecx, &edx);
-	if (eax < 0x8000001f)
-		return;
-
-	/*
-	 * Check for the SME/SEV feature:
-	 *   CPUID Fn8000_001F[EAX]
-	 *   - Bit 0 - Secure Memory Encryption support
-	 *   - Bit 1 - Secure Encrypted Virtualization support
-	 *   CPUID Fn8000_001F[EBX]
-	 *   - Bits 5:0 - Pagetable bit position used to indicate encryption
-	 */
-	eax = 0x8000001f;
-	ecx = 0;
-	native_cpuid(&eax, &ebx, &ecx, &edx);
-	/* Check whether SEV is supported */
-	if (!(eax & BIT(1)))
+	if (sev_check_cpu_support() < 0)
 		return;
 
 	/*
@@ -443,26 +464,8 @@ void sev_enable(struct boot_params *bp)
 
 	/* Now repeat the checks with the SNP CPUID table. */
 
-	/* Recheck the SME/SEV support leaf */
-	eax = 0x80000000;
-	ecx = 0;
-	native_cpuid(&eax, &ebx, &ecx, &edx);
-	if (eax < 0x8000001f)
-		return;
-
-	/*
-	 * Recheck for the SME/SEV feature:
-	 *   CPUID Fn8000_001F[EAX]
-	 *   - Bit 0 - Secure Memory Encryption support
-	 *   - Bit 1 - Secure Encrypted Virtualization support
-	 *   CPUID Fn8000_001F[EBX]
-	 *   - Bits 5:0 - Pagetable bit position used to indicate encryption
-	 */
-	eax = 0x8000001f;
-	ecx = 0;
-	native_cpuid(&eax, &ebx, &ecx, &edx);
-	/* Check whether SEV is supported */
-	if (!(eax & BIT(1))) {
+	bitpos = sev_check_cpu_support();
+	if (bitpos < 0) {
 		if (snp)
 			error("SEV-SNP support indicated by CC blob, but not CPUID.");
 		return;
@@ -494,7 +497,24 @@ void sev_enable(struct boot_params *bp)
 	if (snp && !(sev_status & MSR_AMD64_SEV_SNP_ENABLED))
 		error("SEV-SNP supported indicated by CC blob, but not SEV status MSR.");
 
-	sme_me_mask = BIT_ULL(ebx & 0x3f);
+	sme_me_mask = BIT_ULL(bitpos);
+}
+
+/*
+ * sev_get_status - Retrieve the SEV status mask
+ *
+ * Returns 0 if the CPU is not SEV capable, otherwise the value of the
+ * AMD64_SEV MSR.
+ */
+u64 sev_get_status(void)
+{
+	struct msr m;
+
+	if (sev_check_cpu_support() < 0)
+		return 0;
+
+	boot_rdmsr(MSR_AMD64_SEV, &m);
+	return m.q;
 }
 
 /* Search for Confidential Computing blob in the EFI config table. */
arch/x86/include/asm/sev.h +4 -0
index 66c806784c5256bd..b97d239e18ea25fc 100644
@@ -210,6 +210,8 @@ bool snp_init(struct boot_params *bp);
 void __init __noreturn snp_abort(void);
 int snp_issue_guest_request(u64 exit_code, struct snp_req_data *input, struct snp_guest_request_ioctl *rio);
 void snp_accept_memory(phys_addr_t start, phys_addr_t end);
+u64 snp_get_unsupported_features(u64 status);
+u64 sev_get_status(void);
 #else
 static inline void sev_es_ist_enter(struct pt_regs *regs) { }
 static inline void sev_es_ist_exit(void) { }
@@ -235,6 +237,8 @@ static inline int snp_issue_guest_request(u64 exit_code, struct snp_req_data *in
 }
 
 static inline void snp_accept_memory(phys_addr_t start, phys_addr_t end) { }
+static inline u64 snp_get_unsupported_features(u64 status) { return 0; }
+static inline u64 sev_get_status(void) { return 0; }
 #endif
 
 #endif
drivers/firmware/efi/libstub/x86-stub.c +17 -0
index acb1c65bf8ac6fb3..b4685da2b8d5c243 100644
@@ -15,6 +15,7 @@
 #include <asm/setup.h>
 #include <asm/desc.h>
 #include <asm/boot.h>
+#include <asm/sev.h>
 
 #include "efistub.h"
 #include "x86-stub.h"
@@ -790,6 +791,19 @@ static efi_status_t exit_boot(struct boot_params *boot_params, void *handle)
 	return EFI_SUCCESS;
 }
 
+static bool have_unsupported_snp_features(void)
+{
+	u64 unsupported;
+
+	unsupported = snp_get_unsupported_features(sev_get_status());
+	if (unsupported) {
+		efi_err("Unsupported SEV-SNP features detected: 0x%llx\n",
+			unsupported);
+		return true;
+	}
+	return false;
+}
+
 static void __noreturn enter_kernel(unsigned long kernel_addr,
 				    struct boot_params *boot_params)
 {
@@ -820,6 +834,9 @@ void __noreturn efi_stub_entry(efi_handle_t handle,
 	if (efi_system_table->hdr.signature != EFI_SYSTEM_TABLE_SIGNATURE)
 		efi_exit(handle, EFI_INVALID_PARAMETER);
 
+	if (have_unsupported_snp_features())
+		efi_exit(handle, EFI_UNSUPPORTED);
+
 	if (IS_ENABLED(CONFIG_EFI_DXE_MEM_ATTRIBUTES)) {
 		efi_dxe_table = get_efi_config_table(EFI_DXE_SERVICES_TABLE_GUID);
 		if (efi_dxe_table &&
Signature · 1 line
2.39.2
author maintainer
#23 lore raw

PATCH v8 23/23 x86/efistub: Avoid legacy decompressor when doing EFI boot

In reply to Ard Biesheuvel

The bare metal decompressor code was never really intended to run in a hosted environment such as the EFI boot services, and does a few things that are becoming problematic in the context of EFI boot now that the logo requirements are getting tighter: EFI executables will no longer be allowed to consist of a single executable section that is mapped with read, write and execute permissions if they are intended for use in a context where Secure Boot is enabled (and where Microsoft's set of certificates is used, i.e., every x86 PC built to run Windows)

To avoid stepping on reserved memory before having inspected the E820 tables, and to ensure the correct placement when running a kernel build that is non-relocatable, the bare metal decompressor moves its own executable image to the end of the allocation that was reserved for it, in order to perform the decompression in place. This means the region in question requires both write and execute permissions, which either need to be given upfront (which EFI will no longer permit), or need to be applied on demand using the existing page fault handling framework.

However, the physical placement of the kernel is usually randomized anyway, and even if it isn't, a dedicated decompression output buffer can be allocated anywhere in memory using EFI APIs when still running in the boot services, given that EFI support already implies a relocatable kernel. This means that decompression in place is never necessary, nor is moving the compressed image from one end to the other.

Since EFI already maps all of memory 1:1, it is also unnecessary to create new page tables or handle page faults when decompressing the kernel. That means there is also no need to replace the special exception handlers for SEV. Generally, there is little need to do any of the things that the decompressor does beyond

- initialize SEV encryption, if needed,
- perform the 4/5 level paging switch, if needed,
- decompress the kernel
- relocate the kernel

So do all of this from the EFI stub code, and avoid the bare metal decompressor altogether.

---
 arch/x86/boot/compressed/Makefile       |   5 +
 arch/x86/boot/compressed/efi_mixed.S    |  55 -------
 arch/x86/boot/compressed/head_32.S      |  13 --
 arch/x86/boot/compressed/head_64.S      |  27 ----
 arch/x86/include/asm/efi.h              |   7 +-
 arch/x86/include/asm/sev.h              |   2 +
 drivers/firmware/efi/libstub/x86-stub.c | 166 +++++++++-----------
 7 files changed, 84 insertions(+), 191 deletions(-)
arch/x86/boot/compressed/Makefile +5 -0
index 40d2ff503079e594..71fc531b95b4eede 100644
@@ -74,6 +74,11 @@ LDFLAGS_vmlinux += -z noexecstack
 ifeq ($(CONFIG_LD_IS_BFD),y)
 LDFLAGS_vmlinux += $(call ld-option,--no-warn-rwx-segments)
 endif
+ifeq ($(CONFIG_EFI_STUB),y)
+# ensure that the static EFI stub library will be pulled in, even if it is
+# never referenced explicitly from the startup code
+LDFLAGS_vmlinux += -u efi_pe_entry
+endif
 LDFLAGS_vmlinux += -T
 
 hostprogs	:= mkpiggy
arch/x86/boot/compressed/efi_mixed.S +0 -55

81 lines not on this page · raw message

arch/x86/boot/compressed/head_32.S +0 -13
index 3af4a383615b3e1f..1cfe9802a42fe570 100644
@@ -84,19 +84,6 @@ SYM_FUNC_START(startup_32)
 
 #ifdef CONFIG_RELOCATABLE
 	leal	startup_32@GOTOFF(%edx), %ebx
-
-#ifdef CONFIG_EFI_STUB
-/*
- * If we were loaded via the EFI LoadImage service, startup_32() will be at an
- * offset to the start of the space allocated for the image. efi_pe_entry() will
- * set up image_offset to tell us where the image actually starts, so that we
- * can use the full available buffer.
- *	image_offset = startup_32 - image_base
- * Otherwise image_offset will be zero and has no effect on the calculations.
- */
-	subl    image_offset@GOTOFF(%edx), %ebx
-#endif
-
 	movl	BP_kernel_alignment(%esi), %eax
 	decl	%eax
 	addl    %eax, %ebx
arch/x86/boot/compressed/head_64.S +0 -27
index 28f46051c706724e..bf4a10a5794f1c84 100644
@@ -146,19 +146,6 @@ SYM_FUNC_START(startup_32)
 
 #ifdef CONFIG_RELOCATABLE
 	movl	%ebp, %ebx
-
-#ifdef CONFIG_EFI_STUB
-/*
- * If we were loaded via the EFI LoadImage service, startup_32 will be at an
- * offset to the start of the space allocated for the image. efi_pe_entry will
- * set up image_offset to tell us where the image actually starts, so that we
- * can use the full available buffer.
- *	image_offset = startup_32 - image_base
- * Otherwise image_offset will be zero and has no effect on the calculations.
- */
-	subl    rva(image_offset)(%ebp), %ebx
-#endif
-
 	movl	BP_kernel_alignment(%esi), %eax
 	decl	%eax
 	addl	%eax, %ebx
@@ -335,20 +322,6 @@ SYM_CODE_START(startup_64)
 	/* Start with the delta to where the kernel will run at. */
 #ifdef CONFIG_RELOCATABLE
 	leaq	startup_32(%rip) /* - $startup_32 */, %rbp
-
-#ifdef CONFIG_EFI_STUB
-/*
- * If we were loaded via the EFI LoadImage service, startup_32 will be at an
- * offset to the start of the space allocated for the image. efi_pe_entry will
- * set up image_offset to tell us where the image actually starts, so that we
- * can use the full available buffer.
- *	image_offset = startup_32 - image_base
- * Otherwise image_offset will be zero and has no effect on the calculations.
- */
-	movl    image_offset(%rip), %eax
-	subq	%rax, %rbp
-#endif
-
 	movl	BP_kernel_alignment(%rsi), %eax
 	decl	%eax
 	addq	%rax, %rbp
arch/x86/include/asm/efi.h +5 -2
index 8b4be7cecdb8eb73..b0994ae3bc23f84d 100644
@@ -90,6 +90,8 @@ static inline void efi_fpu_end(void)
 }
 
 #ifdef CONFIG_X86_32
+#define EFI_X86_KERNEL_ALLOC_LIMIT		(SZ_512M - 1)
+
 #define arch_efi_call_virt_setup()					\
 ({									\
 	efi_fpu_begin();						\
@@ -103,8 +105,7 @@ static inline void efi_fpu_end(void)
 })
 
 #else /* !CONFIG_X86_32 */
-
-#define EFI_LOADER_SIGNATURE	"EL64"
+#define EFI_X86_KERNEL_ALLOC_LIMIT		EFI_ALLOC_LIMIT
 
 extern asmlinkage u64 __efi_call(void *fp, ...);
 
@@ -218,6 +219,8 @@ efi_status_t efi_set_virtual_address_map(unsigned long memory_map_size,
 
 #ifdef CONFIG_EFI_MIXED
 
+#define EFI_ALLOC_LIMIT		(efi_is_64bit() ? ULONG_MAX : U32_MAX)
+
 #define ARCH_HAS_EFISTUB_WRAPPERS
 
 static inline bool efi_is_64bit(void)
arch/x86/include/asm/sev.h +2 -0
index b97d239e18ea25fc..5b4a1ce3d36808b4 100644
@@ -164,6 +164,7 @@ static __always_inline void sev_es_nmi_complete(void)
 		__sev_es_nmi_complete();
 }
 extern int __init sev_es_efi_map_ghcbs(pgd_t *pgd);
+extern void sev_enable(struct boot_params *bp);
 
 static inline int rmpadjust(unsigned long vaddr, bool rmp_psize, unsigned long attrs)
 {
@@ -218,6 +219,7 @@ static inline void sev_es_ist_exit(void) { }
 static inline int sev_es_setup_ap_jump_table(struct real_mode_header *rmh) { return 0; }
 static inline void sev_es_nmi_complete(void) { }
 static inline int sev_es_efi_map_ghcbs(pgd_t *pgd) { return 0; }
+static inline void sev_enable(struct boot_params *bp) { }
 static inline int pvalidate(unsigned long vaddr, bool rmp_psize, bool validate) { return 0; }
 static inline int rmpadjust(unsigned long vaddr, bool rmp_psize, unsigned long attrs) { return 0; }
 static inline void setup_ghcb(void) { }
drivers/firmware/efi/libstub/x86-stub.c +72 -94

243 lines not on this page · raw message

Signature · 1 line
2.39.2
maintainer
#24 lore raw
In reply to Ard Biesheuvel
Quoted 8 lines · Ard Biesheuvel

Update the x86 boot path to avoid the bare metal decompressor when booting via the EFI stub. The bare metal decompressor inherits the loader's 1:1 mapping of DRAM when entering in 64-bit mode, and assumes that all of it is mapped read/write/execute, which will no longer be the case on systems built to comply with recently tightened logo requirements (*).

Changes since v7 [10]:

My Zen1 box fails booting with those. It is related to memory encryption because if I supply "mem_encrypt=off", it boots.

The failure is (typing it off from the video from the BMC):

/dev/root: Can't open blockdev
VFS: Cannot open root device "UUID=..."
Please append a correct "root=" boot option;
...

I'll bisect now but it is pretty clear which one is the culprit.

Signature · 4 lines
Regards/Gruss,
    Boris.

https://people.kernel.org/tglx/notes-about-netiquette
author maintainer
#25 lore raw
Quoted 14 lines · Borislav Petkov
Quoted 8 lines · Ard Biesheuvel

Update the x86 boot path to avoid the bare metal decompressor when booting via the EFI stub. The bare metal decompressor inherits the loader's 1:1 mapping of DRAM when entering in 64-bit mode, and assumes that all of it is mapped read/write/execute, which will no longer be the case on systems built to comply with recently tightened logo requirements (*).

Changes since v7 [10]:

My Zen1 box fails booting with those. It is related to memory encryption because if I supply "mem_encrypt=off", it boots.

Quoted 9 lines

The failure is (typing it off from the video from the BMC):

/dev/root: Can't open blockdev
VFS: Cannot open root device "UUID=..."
Please append a correct "root=" boot option;
...

I'll bisect now but it is pretty clear which one is the culprit.

So this is the host booting, right? So is the position of the C bit perhaps getting detect incorrectly?

maintainer
#26 lore raw
Quoted 1 line · Ard Biesheuvel

So this is the host booting, right?

Yes.

Quoted 1 line

So is the position of the C bit perhaps getting detect incorrectly?

I don't know yet. But the evildoer is someone else:

02d47ce2ae02 ("x86/head_64: Store boot_params pointer in callee save register")

after bisection. More staring later as to why...

Signature · 4 lines
Regards/Gruss,
    Boris.

https://people.kernel.org/tglx/notes-about-netiquette
author maintainer
#27 lore raw
Quoted 6 lines · Borislav Petkov
Quoted 1 line · Ard Biesheuvel

So this is the host booting, right?

Yes.

Quoted 8 lines
Quoted 1 line

So is the position of the C bit perhaps getting detect incorrectly?

I don't know yet. But the evildoer is someone else:

02d47ce2ae02 ("x86/head_64: Store boot_params pointer in callee save register")

after bisection. More staring later as to why...

How bizarre.

But that was a bonus patch anyway, so we could just drop it for now.

author maintainer
#28 lore raw
Quoted 12 lines · Ard Biesheuvel
Quoted 10 lines · Borislav Petkov
Quoted 1 line · Ard Biesheuvel

So this is the host booting, right?

Yes.

Quoted 1 line

So is the position of the C bit perhaps getting detect incorrectly?

I don't know yet. But the evildoer is someone else:

Quoted 8 lines
Quoted 4 lines

02d47ce2ae02 ("x86/head_64: Store boot_params pointer in callee save register")

after bisection. More staring later as to why...

How bizarre.

But that was a bonus patch anyway, so we could just drop it for now.

I suspect this should fix the issue:

arch/x86/kernel/head_64.S +1 -0
@@ -110,6 +110,7 @@ SYM_CODE_START_NOALIGN(startup_64)
         * programmed into CR3.
         */
        leaq    _text(%rip), %rdi
+       movq    %r15, %rsi
        call    __startup_64
 
        /* Form the CR3 value being sure to include the CR3 modifier */
maintainer
#29 lore raw

arch/x86/kernel/head_64.S SYM_CODE_START_NOALIGN(startup_64) · line 114

Quoted 10 lines · Ard Biesheuvel

I suspect this should fix the issue:

arch/x86/kernel/head_64.S +1 -0
@@ -110,6 +110,7 @@ SYM_CODE_START_NOALIGN(startup_64)
         * programmed into CR3.
         */
        leaq    _text(%rip), %rdi
+       movq    %r15, %rsi
        call    __startup_64

Yah, I was suspecting we're not passing boot_params properly somewhere. Aaand there it is.

So yes, that fixes it.

Lemme know when you've refreshed your branch so that I can continue testing.

Thx.

Signature · 4 lines
Regards/Gruss,
    Boris.

https://people.kernel.org/tglx/notes-about-netiquette
author maintainer
#30 lore raw
Quoted 16 lines · Borislav Petkov

arch/x86/kernel/head_64.S SYM_CODE_START_NOALIGN(startup_64) · line 114

Quoted 10 lines · Ard Biesheuvel

I suspect this should fix the issue:

arch/x86/kernel/head_64.S +1 -0
@@ -110,6 +110,7 @@ SYM_CODE_START_NOALIGN(startup_64)
         * programmed into CR3.
         */
        leaq    _text(%rip), %rdi
+       movq    %r15, %rsi
        call    __startup_64

Yah, I was suspecting we're not passing boot_params properly somewhere. Aaand there it is.

Quoted 5 lines

So yes, that fixes it.

Lemme know when you've refreshed your branch so that I can continue testing.

https://git.kernel.org/pub/scm/linux/kernel/git/ardb/linux.git/log/?h=x86-efistub-cleanup-v9