arm: dts: k3-am64: Sync DT with Linux
v3 cover arm: dts: k3-am64: Sync DT with Linux
Hi,
This series syncs AM64 DT files from Linux v6.5-rc1.
Tested on AM642-EVM GP SR1.0 and AM642-SK-EVM HS-FS SR2.0.
Couldn't verify Linux boot on AM642-SK-EVM so would appreciate if someone can give a Tested-by for that. Thanks!
cheers,
-roger
Changelog:
v3:
- include board DT file in -r5 DT file.
- move including -u-boot.dtsi file at the top of -r5 DT file.
- drop duplicate nodes
- document why we need to delete clock/power properties from main_timer0
v2:
- Sync with v6.5-rc1
- Rebase on latest uboot/master
- CPSW node cleanup
- Timer node cleanup
Roger Quadros (4):
board: ti: am64x: Recognize AM64-HSEVM
doc: board: ti: am64: Add boot flow diagram Revert "ARM: dts: k3-am642-sk-u-boot: add PMIC node"
arm: dts: k3-am64: Sync DT with Linux v6.5-rc1
arch/arm/dts/k3-am64-main.dtsi | 171 ++++++++- arch/arm/dts/k3-am64-mcu.dtsi | 53 ++- arch/arm/dts/k3-am64-thermal.dtsi | 33 ++ arch/arm/dts/k3-am64.dtsi | 22 +- arch/arm/dts/k3-am642-evm-u-boot.dtsi | 67 ++-- arch/arm/dts/k3-am642-evm.dts | 173 +++++++-- arch/arm/dts/k3-am642-r5-evm.dts | 202 +--------- arch/arm/dts/k3-am642-r5-sk.dts | 209 +---------- arch/arm/dts/k3-am642-sk-u-boot.dtsi | 120 ++---- arch/arm/dts/k3-am642-sk.dts | 166 ++++++--- arch/arm/dts/k3-am642.dtsi | 1 + board/ti/am64x/evm.c | 3 +- doc/board/ti/img/boot_diagram_am64.svg | 496 +++++++++++++++++++++++++ 13 files changed, 1111 insertions(+), 605 deletions(-) create mode 100644 arch/arm/dts/k3-am64-thermal.dtsi create mode 100644 doc/board/ti/img/boot_diagram_am64.svg
Signature · 1 line
2.34.1
PATCH v3 1/4 board: ti: am64x: Recognize AM64-HSEVM
AM64-HSEVM is AM64-GPEVM with High Security Device.
Gets rid of "Unidentified board claims AM64-HSEVM in eeprom header".
--- board/ti/am64x/evm.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
board/ti/am64x/evm.c +2 -1
@@ -18,7 +18,8 @@#include "../common/board_detect.h" -#define board_is_am64x_gpevm () board_ti_k3_is("AM64-GPEVM") +#define board_is_am64x_gpevm () (board_ti_k3_is("AM64-GPEVM") || \ + board_ti_k3_is("AM64-HSEVM"))#define board_is_am64x_skevm () (board_ti_k3_is("AM64-SKEVM") || \ board_ti_k3_is("AM64B-SKEVM"))
Signature · 1 line
2.34.1
Re: [PATCH v3 1/4] board: ti: am64x: Recognize AM64-HSEVM
Quoted 5 lines · Roger Quadros
AM64-HSEVM is AM64-GPEVM with High Security Device.
Gets rid of "Unidentified board claims AM64-HSEVM in eeprom header".
Signed-off-by Roger Quadros <[email protected]>
I think you had Andrew's review here?
Quoted 21 lines
--- board/ti/am64x/evm.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)board/ti/am64x/evm.c +2
-1@@ -18,7 +18,8 @@#include "../common/board_detect.h" -#define board_is_am64x_gpevm () board_ti_k3_is("AM64-GPEVM") +#define board_is_am64x_gpevm () (board_ti_k3_is("AM64-GPEVM") || \ + board_ti_k3_is("AM64-HSEVM"))#define board_is_am64x_skevm () (board_ti_k3_is("AM64-SKEVM") || \ board_ti_k3_is("AM64B-SKEVM"))Signature · 1 line
2.34.1
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH v3 1/4] board: ti: am64x: Recognize AM64-HSEVM
Quoted 8 lines · Nishanth Menon
Quoted 5 lines · Roger Quadros
AM64-HSEVM is AM64-GPEVM with High Security Device.
Gets rid of "Unidentified board claims AM64-HSEVM in eeprom header".
Signed-off-by Roger Quadros <[email protected]>I think you had Andrew's review here?
oops I forgot. will pick it in v4.
Quoted 22 lines
Quoted 21 lines
--- board/ti/am64x/evm.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)board/ti/am64x/evm.c +2
-1@@ -18,7 +18,8 @@#include "../common/board_detect.h" -#define board_is_am64x_gpevm () board_ti_k3_is("AM64-GPEVM") +#define board_is_am64x_gpevm () (board_ti_k3_is("AM64-GPEVM") || \ + board_ti_k3_is("AM64-HSEVM"))#define board_is_am64x_skevm () (board_ti_k3_is("AM64-SKEVM") || \ board_ti_k3_is("AM64B-SKEVM"))Signature · 1 line
2.34.1
Signature · 2 lines
cheers, -roger
PATCH v3 2/4 doc: board: ti: am64: Add boot flow diagram
In reply to Roger QuadrosAdd boot flow diagram for AM64 SoC.
--- doc/board/ti/img/boot_diagram_am64.svg | 496 +++++++++++++++++++++++++ 1 file changed, 496 insertions(+) create mode 100644 doc/board/ti/img/boot_diagram_am64.svg
doc/board/ti/img/boot_diagram_am64.svg new file +496 -0
@@ -0,0 +1,496 @@ +<?xml version="1.0" encoding="UTF-8" standalone="no"?> +<svg version="1.1" width="706px" height="951px" viewBox="-0.5 -0.5 706 951" id="svg356" sodipodi:docname="boot_diagram_am64.svg" inkscape:version="1.1.2 (0a00cf5339, 2022-02-04)" xmlns:inkscape="http://www.inkscape.org/namespaces/inkscape" xmlns:sodipodi="http://sodipodi.sourceforge.net/DTD/sodipodi-0.dtd" xmlns:xlink="http://www.w3.org/1999/xlink" xmlns="http://www.w3.org/2000/svg" xmlns:svg="http://www.w3.org/2000/svg" xmlns:xhtml="http://www.w3.org/1999/xhtml"> + <sodipodi:namedview id="namedview358" pagecolor="#ffffff" bordercolor="#666666" borderopacity="1.0" inkscape:pageshadow="2" inkscape:pageopacity="0.0" inkscape:pagecheckerboard="0" showgrid="false" inkscape:zoom="2.8685594" inkscape:cx="163.14809" inkscape:cy="291.43548" inkscape:window-width="3440" inkscape:window-height="1416" inkscape:window-x="0" inkscape:window-y="0" inkscape:window-maximized="1" inkscape:current-layer="svg356"/> + <defs id="defs2"/> + <g id="g346"> + <rect x="235.5" y="50" width="137.5" height="40" rx="6" ry="6" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect4"/> + <path d="M 304.25 90 L 304.25 940" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" stroke-dasharray="3 3" pointer-events="all" id="path6"/> + <g transform="translate(-0.5 -0.5)" id="g12"> + <switch id="switch10"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 136px; height: 1px; padding-top: 70px; margin-left: 237px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Verdana; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Cortex-R</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="304" y="74" fill="rgb(0, 0, 0)" font-family="Verdana" font-size="12px" text-anchor="middle" id="text8">Cortex-R</text> + </switch> + </g> + <rect x="298.75" y="160" width="10" height="130" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect14"/> + <rect x="301" y="161" width="71.5" height="30" fill="#ffe6cc" stroke="#d79b00" pointer-events="all" id="rect16"/> + <g transform="translate(-0.5 -0.5)" id="g22"> + <switch id="switch20"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 70px; height: 1px; padding-top: 176px; margin-left: 302px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">ROM</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="337" y="180" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text18">ROM</text> + </switch> + </g> + <rect x="299.75" y="305" width="10" height="205" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect24"/> + <rect x="302" y="306" width="105.5" height="30" fill="#d5e8d4" stroke="#82b366" pointer-events="all" id="rect26"/> + <g transform="translate(-0.5 -0.5)" id="g32"> + <switch id="switch30"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 104px; height: 1px; padding-top: 321px; margin-left: 303px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Cortex-R SPL</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="355" y="325" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text28">Cortex-R SPL</text> + </switch> + </g> + <rect x="308.75" y="190" width="90" height="40" rx="6" ry="6" fill="none" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect34"/> + <g transform="translate(-0.5 -0.5)" id="g40"> + <switch id="switch38"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 88px; height: 1px; padding-top: 210px; margin-left: 310px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Load and auth tiboot3.bin</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="354" y="214" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text36">Load and auth t...</text> + </switch> + </g> + <rect x="309" y="262" width="90" height="32" rx="4.8" ry="4.8" fill="none" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect42"/> + <g transform="translate(-0.5 -0.5)" id="g48"> + <switch id="switch46"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 88px; height: 1px; padding-top: 278px; margin-left: 310px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Load system<xhtml:br /> +config data</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="354" y="282" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text44">Load system...</text> + </switch> + </g> + <rect x="310" y="336" width="90" height="32" rx="4.8" ry="4.8" fill="none" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect50"/> + <g transform="translate(-0.5 -0.5)" id="g56"> + <switch id="switch54"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 88px; height: 1px; padding-top: 352px; margin-left: 311px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">DDR Config</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="355" y="356" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text52">DDR Config</text> + </switch> + </g> + <rect x="310" y="368" width="90" height="32" rx="4.8" ry="4.8" fill="none" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect58"/> + <g transform="translate(-0.5 -0.5)" id="g64"> + <switch id="switch62"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 88px; height: 1px; padding-top: 384px; margin-left: 311px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Load tispl.bin</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="355" y="388" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text60">Load tispl.bin</text> + </switch> + </g> + <rect x="310" y="440" width="90" height="32" rx="4.8" ry="4.8" fill="none" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect66"/> + <g transform="translate(-0.5 -0.5)" id="g72"> + <switch id="switch70"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 88px; height: 1px; padding-top: 456px; margin-left: 311px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Start Cortex-A</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="355" y="460" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text68">Start Cortex-A</text> + </switch> + </g> + <path d="M 299 456 L 139.37 456" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path74"/> + <path d="M 134.12 456 L 141.12 452.5 L 139.37 456 L 141.12 459.5 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path76"/> + <g transform="translate(-0.5 -0.5)" id="g82"> + <switch id="switch80"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 1px; height: 1px; padding-top: 440px; margin-left: 257px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); background-color: rgb(255, 255, 255); "> + <xhtml:div style="display: inline-block; font-size: 11px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; background-color: rgb(255, 255, 255); white-space: nowrap;">Start Cortex-A</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="257" y="443" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="11px" text-anchor="middle" id="text78">Start Cort...</text> + </switch> + </g> + <path d="M 481 601 L 139.37 601" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path84"/> + <path d="M 134.12 601 L 141.12 597.5 L 139.37 601 L 141.12 604.5 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path86"/> + <path d="M 481 711 L 139.37 711" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path88"/> + <path d="M 134.12 711 L 141.12 707.5 L 139.37 711 L 141.12 714.5 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path90"/> + <path d="M 481 791 L 139.37 791" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path92"/> + <path d="M 134.12 791 L 141.12 787.5 L 139.37 791 L 141.12 794.5 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path94"/> + <path d="M 481 879 L 139.37 881.95" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path96"/> + <path d="M 134.12 881.99 L 141.09 878.43 L 139.37 881.95 L 141.15 885.43 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path98"/> + <rect x="437" y="50" width="100" height="40" rx="6" ry="6" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect100"/> + <path d="M 487 90 L 487 820" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" stroke-dasharray="3 3" pointer-events="all" id="path102"/> + <g transform="translate(-0.5 -0.5)" id="g108"> + <switch id="switch106"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 98px; height: 1px; padding-top: 70px; margin-left: 438px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Verdana; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Cortex-A</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="487" y="74" fill="rgb(0, 0, 0)" font-family="Verdana" font-size="12px" text-anchor="middle" id="text104">Cortex-A</text> + </switch> + </g> + <rect x="482" y="510" width="10" height="70" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect110"/> + <path d="M 482 565 L 139.37 565" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path112"/> + <path d="M 134.12 565 L 141.12 561.5 L 139.37 565 L 141.12 568.5 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path114"/> + <rect x="577" y="50" width="116.5" height="40" rx="6" ry="6" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect116"/> + <path d="M 635.25 90 L 635.25 950" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" stroke-dasharray="3 3" pointer-events="all" id="path118"/> + <g transform="translate(-0.5 -0.5)" id="g124"> + <switch id="switch122"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 115px; height: 1px; padding-top: 70px; margin-left: 578px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Verdana; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Cortex-R/M<xhtml:br /> +C6x/C7x</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="635" y="74" fill="rgb(0, 0, 0)" font-family="Verdana" font-size="12px" text-anchor="middle" id="text120">Cortex-R/M...</text> + </switch> + </g> + <rect x="631" y="910" width="10" height="38" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect126"/> + <rect x="633" y="912" width="71.5" height="30" fill="#e1d5e7" stroke="#9673a6" pointer-events="all" id="rect128"/> + <g transform="translate(-0.5 -0.5)" id="g134"> + <switch id="switch132"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 70px; height: 1px; padding-top: 927px; margin-left: 634px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Aux f/w</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="669" y="931" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text130">Aux f/w</text> + </switch> + </g> + <rect x="77" y="50" width="100" height="40" rx="6" ry="6" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect136"/> + <path d="M 127 90 L 127 940" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" stroke-dasharray="3 3" pointer-events="all" id="path138"/> + <g transform="translate(-0.5 -0.5)" id="g144"> + <switch id="switch142"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 98px; height: 1px; padding-top: 70px; margin-left: 78px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Verdana; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">TIFS/DMSC</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="127" y="74" fill="rgb(0, 0, 0)" font-family="Verdana" font-size="12px" text-anchor="middle" id="text140">TIFS/DMSC</text> + </switch> + </g> + <rect x="122" y="130" width="10" height="110" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect146"/> + <rect x="79" y="132" width="50" height="30" fill="#ffe6cc" stroke="#d79b00" pointer-events="all" id="rect148"/> + <g transform="translate(-0.5 -0.5)" id="g154"> + <switch id="switch152"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 48px; height: 1px; padding-top: 147px; margin-left: 80px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">ROM</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="104" y="151" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text150">ROM</text> + </switch> + </g> + <rect x="122" y="253" width="10" height="687" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect156"/> + <path d="M 297 238 L 138.37 238" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path158"/> + <path d="M 133.12 238 L 140.12 234.5 L 138.37 238 L 140.12 241.5 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path160"/> + <g transform="translate(-0.5 -0.5)" id="g166"> + <switch id="switch164"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 1px; height: 1px; padding-top: 230px; margin-left: 267px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); background-color: rgb(255, 255, 255); "> + <xhtml:div style="display: inline-block; font-size: 11px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; background-color: rgb(255, 255, 255); white-space: nowrap;">Start SYSFW</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="267" y="233" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="11px" text-anchor="middle" id="text162">Start SYSFW</text> + </switch> + </g> + <rect x="80" y="255" width="50" height="30" fill="#f8cecc" stroke="#b85450" pointer-events="all" id="rect168"/> + <g transform="translate(-0.5 -0.5)" id="g174"> + <switch id="switch172"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 48px; height: 1px; padding-top: 270px; margin-left: 81px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">SYSFW</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="105" y="274" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text170">SYSFW</text> + </switch> + </g> + <path d="M 62 0 L 178 0 L 192 14 L 192 35 L 62 35 L 62 0 Z" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path176"/> + <path d="M 178 0 L 178 14 L 192 14" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path178"/> + <g transform="translate(-0.5 -0.5)" id="g184"> + <switch id="switch182"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe flex-start; justify-content: unsafe center; width: 128px; height: 1px; padding-top: 1px; margin-left: 63px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Verdana; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Security Enclave Boot Processor</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="127" y="13" fill="rgb(0, 0, 0)" font-family="Verdana" font-size="12px" text-anchor="middle" id="text180">Security Enclave Boot...</text> + </switch> + </g> + <path d="M 241 0 L 361 0 L 375 14 L 375 35 L 241 35 L 241 0 Z" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path186"/> + <path d="M 361 0 L 361 14 L 375 14" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path188"/> + <g transform="translate(-0.5 -0.5)" id="g194"> + <switch id="switch192"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe flex-start; justify-content: unsafe center; width: 132px; height: 1px; padding-top: 1px; margin-left: 242px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Verdana; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Boot Loader <xhtml:br /> +Processor</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="308" y="13" fill="rgb(0, 0, 0)" font-family="Verdana" font-size="12px" text-anchor="middle" id="text190">Boot Loader...</text> + </switch> + </g> + <path d="M 437 0 L 523 0 L 537 14 L 537 35 L 437 35 L 437 0 Z" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path196"/> + <path d="M 523 0 L 523 14 L 537 14" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path198"/> + <g transform="translate(-0.5 -0.5)" id="g204"> + <switch id="switch202"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe flex-start; justify-content: unsafe center; width: 98px; height: 1px; padding-top: 1px; margin-left: 438px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Verdana; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Main CPU</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="487" y="13" fill="rgb(0, 0, 0)" font-family="Verdana" font-size="12px" text-anchor="middle" id="text200">Main CPU</text> + </switch> + </g> + <path d="M 577 0 L 663 0 L 677 14 L 677 35 L 577 35 L 577 0 Z" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path206"/> + <path d="M 663 0 L 663 14 L 677 14" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path208"/> + <g transform="translate(-0.5 -0.5)" id="g214"> + <switch id="switch212"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe flex-start; justify-content: unsafe center; width: 98px; height: 1px; padding-top: 1px; margin-left: 578px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Verdana; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Auxiliary<xhtml:br /> +Processor</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="627" y="13" fill="rgb(0, 0, 0)" font-family="Verdana" font-size="12px" text-anchor="middle" id="text210">Auxiliary...</text> + </switch> + </g> + <path d="M 7 120 L 120.63 120" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" stroke-dasharray="12 12" pointer-events="stroke" id="path216"/> + <path d="M 125.88 120 L 118.88 123.5 L 120.63 120 L 118.88 116.5 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path218"/> + <g transform="translate(-0.5 -0.5)" id="g224"> + <switch id="switch222"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe flex-end; justify-content: unsafe flex-start; width: 1px; height: 1px; padding-top: 118px; margin-left: 9px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: left;" data-drawio-colors="color: rgb(0, 0, 0); background-color: rgb(255, 255, 255); "> + <xhtml:div style="display: inline-block; font-size: 11px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; background-color: rgb(255, 255, 255); white-space: nowrap;">H/w Seq: Reset rls</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="9" y="118" fill="#000000" font-family="Helvetica" font-size="11px" id="text220">H/w Seq: Reset rls</text> + </switch> + </g> + <path d="M 298 200 L 138.37 199.98" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path226"/> + <path d="M 133.12 199.98 L 140.12 196.48 L 138.37 199.98 L 140.12 203.48 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path228"/> + <g transform="translate(-0.5 -0.5)" id="g234"> + <switch id="switch232"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 1px; height: 1px; padding-top: 190px; margin-left: 257px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); background-color: rgb(255, 255, 255); "> + <xhtml:div style="display: inline-block; font-size: 11px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; background-color: rgb(255, 255, 255); white-space: nowrap;">Auth tiboot3.bin</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="257" y="193" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="11px" text-anchor="middle" id="text230">Auth tiboo...</text> + </switch> + </g> + <path d="M 133 159 L 297.38 159" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path236"/> + <path d="M 302.63 159 L 295.63 162.5 L 297.38 159 L 295.63 155.5 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path238"/> + <g transform="translate(-0.5 -0.5)" id="g244"> + <switch id="switch242"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 1px; height: 1px; padding-top: 150px; margin-left: 177px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); background-color: rgb(255, 255, 255); "> + <xhtml:div style="display: inline-block; font-size: 11px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; background-color: rgb(255, 255, 255); white-space: nowrap;">Release Reset</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="177" y="153" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="11px" text-anchor="middle" id="text240">Release Re...</text> + </switch> + </g> + <path d="M 299 281.94 L 139.37 281.04" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path246"/> + <path d="M 134.12 281.01 L 141.14 277.55 L 139.37 281.04 L 141.1 284.55 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path248"/> + <g transform="translate(-0.5 -0.5)" id="g254"> + <switch id="switch252"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 1px; height: 1px; padding-top: 270px; margin-left: 237px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); background-color: rgb(255, 255, 255); "> + <xhtml:div style="display: inline-block; font-size: 11px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; background-color: rgb(255, 255, 255); white-space: nowrap;">Load system config data</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="237" y="273" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="11px" text-anchor="middle" id="text250">Load syste...</text> + </switch> + </g> + <rect x="308.75" y="230" width="90" height="32" rx="4.8" ry="4.8" fill="none" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect256"/> + <g transform="translate(-0.5 -0.5)" id="g262"> + <switch id="switch260"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 88px; height: 1px; padding-top: 246px; margin-left: 310px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Start SYSFW</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="354" y="250" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text258">Start SYSFW</text> + </switch> + </g> + <path d="M 133 511 L 137 511 L 476.63 511" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path264"/> + <path d="M 481.88 511 L 474.88 514.5 L 476.63 511 L 474.88 507.5 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path266"/> + <g transform="translate(-0.5 -0.5)" id="g272"> + <switch id="switch270"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 1px; height: 1px; padding-top: 500px; margin-left: 177px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); background-color: rgb(255, 255, 255); "> + <xhtml:div style="display: inline-block; font-size: 11px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; background-color: rgb(255, 255, 255); white-space: nowrap;">Release Reset</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="177" y="503" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="11px" text-anchor="middle" id="text268">Release Re...</text> + </switch> + </g> + <rect x="484" y="513" width="71.5" height="30" fill="#d5e8d4" stroke="#82b366" pointer-events="all" id="rect274"/> + <g transform="translate(-0.5 -0.5)" id="g280"> + <switch id="switch278"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 70px; height: 1px; padding-top: 528px; margin-left: 485px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">TF-A </xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="520" y="532" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text276">TF-A </text> + </switch> + </g> + <rect x="482" y="581" width="10" height="70" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect282"/> + <rect x="484" y="584" width="71.5" height="30" fill="#d5e8d4" stroke="#82b366" pointer-events="all" id="rect284"/> + <g transform="translate(-0.5 -0.5)" id="g290"> + <switch id="switch288"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 70px; height: 1px; padding-top: 599px; margin-left: 485px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">OP-TEE</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="520" y="603" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text286">OP-TEE</text> + </switch> + </g> + <rect x="482" y="662" width="10" height="78" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect292"/> + <rect x="484" y="665" width="83" height="30" fill="#d5e8d4" stroke="#82b366" pointer-events="all" id="rect294"/> + <g transform="translate(-0.5 -0.5)" id="g300"> + <switch id="switch298"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 81px; height: 1px; padding-top: 680px; margin-left: 485px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Cortex A SPL</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="526" y="684" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text296">Cortex A SPL</text> + </switch> + </g> + <rect x="482" y="748" width="10" height="192" fill="rgb(255, 255, 255)" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect302"/> + <rect x="484" y="751" width="83" height="30" fill="#d5e8d4" stroke="#82b366" pointer-events="all" id="rect304"/> + <g transform="translate(-0.5 -0.5)" id="g310"> + <switch id="switch308"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 81px; height: 1px; padding-top: 766px; margin-left: 485px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">U-Boot</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="526" y="770" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text306">U-Boot</text> + </switch> + </g> + <rect x="492" y="700" width="103" height="32" rx="4.8" ry="4.8" fill="none" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect312"/> + <g transform="translate(-0.5 -0.5)" id="g318"> + <switch id="switch316"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 101px; height: 1px; padding-top: 716px; margin-left: 493px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Load u-boot.img</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="544" y="720" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text314">Load u-boot.img</text> + </switch> + </g> + <rect x="492" y="820" width="103" height="32" rx="4.8" ry="4.8" fill="none" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect320"/> + <g transform="translate(-0.5 -0.5)" id="g326"> + <switch id="switch324"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 101px; height: 1px; padding-top: 836px; margin-left: 493px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Load Aux core f/w<xhtml:br /> +(optional)</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="544" y="840" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text322">Load Aux core f/w...</text> + </switch> + </g> + <rect x="492" y="860" width="103" height="32" rx="4.8" ry="4.8" fill="none" stroke="rgb(0, 0, 0)" pointer-events="all" id="rect328"/> + <g transform="translate(-0.5 -0.5)" id="g334"> + <switch id="switch332"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 101px; height: 1px; padding-top: 876px; margin-left: 493px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); "> + <xhtml:div style="display: inline-block; font-size: 12px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; white-space: normal; overflow-wrap: normal;">Start Aux core<xhtml:br /> +(optional)</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="544" y="880" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="12px" text-anchor="middle" id="text330">Start Aux core...</text> + </switch> + </g> + <path d="M 132 909 L 628.38 909" fill="none" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="stroke" id="path336"/> + <path d="M 633.63 909 L 626.63 912.5 L 628.38 909 L 626.63 905.5 Z" fill="rgb(0, 0, 0)" stroke="rgb(0, 0, 0)" stroke-miterlimit="10" pointer-events="all" id="path338"/> + <g transform="translate(-0.5 -0.5)" id="g344"> + <switch id="switch342"> + <foreignObject style="overflow: visible; text-align: left;" pointer-events="none" width="100%" height="100%" requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility"> + <xhtml:div style="display: flex; align-items: unsafe center; justify-content: unsafe center; width: 1px; height: 1px; padding-top: 900px; margin-left: 203px;"> + <xhtml:div style="box-sizing: border-box; font-size: 0px; text-align: center;" data-drawio-colors="color: rgb(0, 0, 0); background-color: rgb(255, 255, 255); "> + <xhtml:div style="display: inline-block; font-size: 11px; font-family: Helvetica; color: rgb(0, 0, 0); line-height: 1.2; pointer-events: all; background-color: rgb(255, 255, 255); white-space: nowrap;">Release Reset</xhtml:div> + </xhtml:div> + </xhtml:div> + </foreignObject> + <text x="203" y="903" fill="rgb(0, 0, 0)" font-family="Helvetica" font-size="11px" text-anchor="middle" id="text340">Release Re...</text> + </switch> + </g> + </g> + <switch id="switch354"> + <g requiredFeatures="http://www.w3.org/TR/SVG11/feature#Extensibility" id="g348"/> + <a transform="translate(0,-5)" xlink:href="https://www.drawio.com/doc/faq/svg-export-text-problems" target="_blank" id="a352"> + <text text-anchor="middle" font-size="10px" x="50%" y="100%" id="text350">Text is not SVG - cannot display</text> + </a> + </switch> +</svg>
Signature · 1 line
2.34.1
Re: [PATCH v3 2/4] doc: board: ti: am64: Add boot flow diagram
Quoted 15 lines · Roger Quadros
Add boot flow diagram for AM64 SoC.
Suggested-by Nishanth Menon <[email protected]>Signed-off-by Roger Quadros <[email protected]>--- doc/board/ti/img/boot_diagram_am64.svg | 496 +++++++++++++++++++++++++ 1 file changed, 496 insertions(+) create mode 100644 doc/board/ti/img/boot_diagram_am64.svgdoc/board/ti/img/boot_diagram_am64.svg new file +0
-0
doc/board/ti/img/boot_diagram_am64.svg line 1
Quoted 1 line
doc/board/ti/img/boot_diagram_am64.svg new file +1
-0@@ -0,0 +1,496 @@ +<?xml version="1.0" encoding="UTF-8" standalone="no"?>
As one of those hand-edit things, please add a license tag.
Signature · 1 line
Tom
Re: [PATCH v3 2/4] doc: board: ti: am64: Add boot flow diagram
In reply to Roger QuadrosQuoted 15 lines · Roger Quadros
Add boot flow diagram for AM64 SoC.
Suggested-by Nishanth Menon <[email protected]>Signed-off-by Roger Quadros <[email protected]>--- doc/board/ti/img/boot_diagram_am64.svg | 496 +++++++++++++++++++++++++ 1 file changed, 496 insertions(+) create mode 100644 doc/board/ti/img/boot_diagram_am64.svgdoc/board/ti/img/boot_diagram_am64.svg new file +0
-0
doc/board/ti/img/boot_diagram_am64.svg line 1
Quoted 1 line
doc/board/ti/img/boot_diagram_am64.svg new file +1
-0@@ -0,0 +1,496 @@ +<?xml version="1.0" encoding="UTF-8" standalone="no"?>
yup - need to add license, but more importantly, needs a am64x_evm.rst where the svg exists.
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH v3 2/4] doc: board: ti: am64: Add boot flow diagram
Quoted 10 lines · Nishanth Menon
Quoted 9 lines · Roger Quadros
Add boot flow diagram for AM64 SoC.
Suggested-by Nishanth Menon <[email protected]>Signed-off-by Roger Quadros <[email protected]>--- doc/board/ti/img/boot_diagram_am64.svg | 496 +++++++++++++++++++++++++ 1 file changed, 496 insertions(+) create mode 100644 doc/board/ti/img/boot_diagram_am64.svg
Quoted 11 lines
doc/board/ti/img/boot_diagram_am64.svg line 1
Quoted 7 lines
doc/board/ti/img/boot_diagram_am64.svg new file +1
-0@@ -0,0 +1,496 @@ +<?xml version="1.0" encoding="UTF-8" standalone="no"?>yup - need to add license, but more importantly, needs a
am64x_evm.rstwhere the svg exists.
OK. Other SVG files also seem to lack the license tag. unless I'm looking for the wrong one :P
Signature · 2 lines
cheers, -roger
Re: [PATCH v3 2/4] doc: board: ti: am64: Add boot flow diagram
Quoted 25 lines · Roger Quadros
Quoted 10 lines · Nishanth Menon
Quoted 9 lines · Roger Quadros
Add boot flow diagram for AM64 SoC.
Suggested-by Nishanth Menon <[email protected]>Signed-off-by Roger Quadros <[email protected]>--- doc/board/ti/img/boot_diagram_am64.svg | 496 +++++++++++++++++++++++++ 1 file changed, 496 insertions(+) create mode 100644 doc/board/ti/img/boot_diagram_am64.svgQuoted 11 lines
doc/board/ti/img/boot_diagram_am64.svg line 1
Quoted 7 lines
doc/board/ti/img/boot_diagram_am64.svg new file +1
-0@@ -0,0 +1,496 @@ +<?xml version="1.0" encoding="UTF-8" standalone="no"?>yup - need to add license, but more importantly, needs a
am64x_evm.rstwhere the svg exists.
Quoted 1 line
OK. Other SVG files also seem to lack the license tag. unless I'm looking for the wrong one :P
no you aren't looking at the wrong svg files: because
https://lore.kernel.org/u-boot/[email protected]/
is waiting for the window to open back up.
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
PATCH v3 3/4 Revert "ARM: dts: k3-am642-sk-u-boot: add PMIC node"
In reply to Roger QuadrosThis reverts commit 28a4c3113445d4400639f357fae0def007a41093.
This node should be in the board DT file and should come from upstream. Moreover, this PMIC is no present on all variants of am642-sk and will need a separate board DT file.
--- arch/arm/dts/k3-am642-sk-u-boot.dtsi | 61 ---------------------------- 1 file changed, 61 deletions(-)
arch/arm/dts/k3-am642-sk-u-boot.dtsi +0 -61
@@ -54,67 +54,6 @@ pinctrl-names = "default"; pinctrl-0 = <&main_i2c0_pins_default>; clock-frequency = <400000>; - - tps65219: pmic@30 { - compatible = "ti,tps65219"; - reg = <0x30>; - - regulators { - buck1_reg: buck1 { - regulator-name = "VDD_CORE"; - regulator-min-microvolt = <750000>; - regulator-max-microvolt = <750000>; - regulator-boot-on; - regulator-always-on; - }; - - buck2_reg: buck2 { - regulator-name = "VCC1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-boot-on; - regulator-always-on; - }; - - buck3_reg: buck3 { - regulator-name = "VDD_LPDDR4"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo1_reg: ldo1 { - regulator-name = "VDDSHV_SD_IO_PMIC"; - regulator-min-microvolt = <33000000>; - regulator-max-microvolt = <33000000>; - }; - - ldo2_reg: ldo2 { - regulator-name = "VDDAR_CORE"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <850000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo3_reg: ldo3 { - regulator-name = "VDDA_1V8"; - regulator-min-microvolt = <18000000>; - regulator-max-microvolt = <18000000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo4_reg: ldo4 { - regulator-name = "VDD_PHY_2V5"; - regulator-min-microvolt = <25000000>; - regulator-max-microvolt = <25000000>; - regulator-boot-on; - regulator-always-on; - }; - }; - }; }; &main_uart0 {
Signature · 1 line
2.34.1
PATCH v3 4/4 arm: dts: k3-am64: Sync DT with Linux v6.5-rc1
In reply to Roger QuadrosSync all am642-evm/am642-sk related DT files
with Linux v6.5-rc1.
- drop timer1 in favor of main_timer0 in am64-main.dtsi. Need to delete clock & power domain properties of main_timer1 in -r5.dts else won't boot. This is because timer_init is done during rproc_start to start System Firmware, but we can't do any clock/power-domain operations before System Firmware starts.
- drop cpsw3g custom DT property 'mac_efuse' and custom DT node cpsw-phy-sel as driver picks these from standard property/node.
- include board dts file in -r5 dts file to avoid duplication of nodes. Include -u-boot.dtsi on top.
- drop duplicate nodes in -r5 dts and -u-boot.dtsi
--- arch/arm/dts/k3-am64-main.dtsi | 171 ++++++++++++++++++++- arch/arm/dts/k3-am64-mcu.dtsi | 53 ++++++- arch/arm/dts/k3-am64-thermal.dtsi | 33 ++++ arch/arm/dts/k3-am64.dtsi | 22 +-- arch/arm/dts/k3-am642-evm-u-boot.dtsi | 67 +++++---- arch/arm/dts/k3-am642-evm.dts | 173 ++++++++++++++++----- arch/arm/dts/k3-am642-r5-evm.dts | 202 +++---------------------- arch/arm/dts/k3-am642-r5-sk.dts | 209 +++----------------------- arch/arm/dts/k3-am642-sk-u-boot.dtsi | 59 ++++---- arch/arm/dts/k3-am642-sk.dts | 166 ++++++++++++++------ arch/arm/dts/k3-am642.dtsi | 1 + 11 files changed, 613 insertions(+), 543 deletions(-) create mode 100644 arch/arm/dts/k3-am64-thermal.dtsi
arch/arm/dts/k3-am64-main.dtsi +164 -7
@@ -228,12 +228,161 @@ }; }; + main_timer0: timer@2400000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2400000 0x00 0x400>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 36 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 36 1>; + assigned-clock-parents = <&k3_clks 36 2>; + power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer1: timer@2410000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2410000 0x00 0x400>; + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 37 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 37 1>; + assigned-clock-parents = <&k3_clks 37 2>; + power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer2: timer@2420000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2420000 0x00 0x400>; + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 38 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 38 1>; + assigned-clock-parents = <&k3_clks 38 2>; + power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer3: timer@2430000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2430000 0x00 0x400>; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 39 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 39 1>; + assigned-clock-parents = <&k3_clks 39 2>; + power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer4: timer@2440000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2440000 0x00 0x400>; + interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 40 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 40 1>; + assigned-clock-parents = <&k3_clks 40 2>; + power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer5: timer@2450000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2450000 0x00 0x400>; + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 41 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 41 1>; + assigned-clock-parents = <&k3_clks 41 2>; + power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer6: timer@2460000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2460000 0x00 0x400>; + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 42 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 42 1>; + assigned-clock-parents = <&k3_clks 42 2>; + power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer7: timer@2470000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2470000 0x00 0x400>; + interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 43 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 43 1>; + assigned-clock-parents = <&k3_clks 43 2>; + power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer8: timer@2480000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2480000 0x00 0x400>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 44 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 44 1>; + assigned-clock-parents = <&k3_clks 44 2>; + power-domains = <&k3_pds 44 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer9: timer@2490000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2490000 0x00 0x400>; + interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 45 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 45 1>; + assigned-clock-parents = <&k3_clks 45 2>; + power-domains = <&k3_pds 45 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer10: timer@24a0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24a0000 0x00 0x400>; + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 46 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 46 1>; + assigned-clock-parents = <&k3_clks 46 2>; + power-domains = <&k3_pds 46 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer11: timer@24b0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24b0000 0x00 0x400>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 47 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 47 1>; + assigned-clock-parents = <&k3_clks 47 2>; + power-domains = <&k3_pds 47 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_esm: esm@420000 { + compatible = "ti,j721e-esm"; + reg = <0x00 0x420000 0x00 0x1000>; + ti,esm-pins = <160>, <161>; + }; + main_uart0: serial@2800000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x02800000 0x00 0x100>; interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 146 0>; clock-names = "fclk";
@@ -245,7 +394,6 @@ reg = <0x00 0x02810000 0x00 0x100>; interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 152 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 152 0>; clock-names = "fclk";
@@ -257,7 +405,6 @@ reg = <0x00 0x02820000 0x00 0x100>; interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 153 0>; clock-names = "fclk";
@@ -269,7 +416,6 @@ reg = <0x00 0x02830000 0x00 0x100>; interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 154 0>; clock-names = "fclk";
@@ -281,7 +427,6 @@ reg = <0x00 0x02840000 0x00 0x100>; interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 155 0>; clock-names = "fclk";
@@ -293,7 +438,6 @@ reg = <0x00 0x02850000 0x00 0x100>; interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 156 0>; clock-names = "fclk";
@@ -305,7 +449,6 @@ reg = <0x00 0x02860000 0x00 0x100>; interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 158 0>; clock-names = "fclk";
@@ -676,6 +819,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; mailbox0_cluster3: mailbox@29030000 {
@@ -686,6 +830,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; mailbox0_cluster4: mailbox@29040000 {
@@ -696,6 +841,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; mailbox0_cluster5: mailbox@29050000 {
@@ -706,6 +852,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; mailbox0_cluster6: mailbox@29060000 {
@@ -715,6 +862,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; mailbox0_cluster7: mailbox@29070000 {
@@ -724,6 +872,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; main_r5fss0: r5fss@78000000 {
@@ -1392,4 +1541,12 @@ clock-names = "fck"; status = "disabled"; }; + + main_vtm0: temperature-sensor@b00000 { + compatible = "ti,j7200-vtm"; + reg = <0x00 0xb00000 0x00 0x400>, + <0x00 0xb01000 0x00 0x400>; + power-domains = <&k3_pds 95 TI_SCI_PD_EXCLUSIVE>; + #thermal-sensor-cells = <1>; + }; };
arch/arm/dts/k3-am64-mcu.dtsi +51 -2
73 lines not on this page · raw message
arch/arm/dts/k3-am64-thermal.dtsi new file +33 -0
@@ -0,0 +1,33 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include <dt-bindings/thermal/thermal.h> + +thermal_zones: thermal-zones { + main0_thermal: main0-thermal { + polling-delay-passive = <250>; /* milliSeconds */ + polling-delay = <500>; /* milliSeconds */ + thermal-sensors = <&main_vtm0 0>; + + trips { + main0_crit: main0-crit { + temperature = <105000>; /* milliCelsius */ + hysteresis = <2000>; /* milliCelsius */ + type = "critical"; + }; + }; + }; + + main1_thermal: main1-thermal { + polling-delay-passive = <250>; /* milliSeconds */ + polling-delay = <500>; /* milliSeconds */ + thermal-sensors = <&main_vtm0 1>; + + trips { + main1_crit: main1-crit { + temperature = <105000>; /* milliCelsius */ + hysteresis = <2000>; /* milliCelsius */ + type = "critical"; + }; + }; + }; +};
arch/arm/dts/k3-am64.dtsi +5 -17
@@ -8,9 +8,10 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/pinctrl/k3.h> #include <dt-bindings/soc/ti,sci_pm_domain.h> +#include "k3-pinctrl.h" + / { model = "Texas Instruments K3 AM642 SoC"; compatible = "ti,am642";
@@ -18,22 +19,6 @@ #address-cells = <2>; #size-cells = <2>; - aliases { - serial0 = &mcu_uart0; - serial1 = &mcu_uart1; - serial2 = &main_uart0; - serial3 = &main_uart1; - serial4 = &main_uart2; - serial5 = &main_uart3; - serial6 = &main_uart4; - serial7 = &main_uart5; - serial8 = &main_uart6; - ethernet0 = &cpsw_port1; - ethernet1 = &cpsw_port2; - mmc0 = &sdhci0; - mmc1 = &sdhci1; - }; - chosen { }; firmware {
@@ -69,6 +54,7 @@ <0x00 0x00420000 0x00 0x00420000 0x00 0x00001000>, /* ESM0 */ <0x00 0x00600000 0x00 0x00600000 0x00 0x00001100>, /* GPIO */ <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* Timesync router */ + <0x00 0x00b00000 0x00 0x00b00000 0x00 0x00002400>, /* VTM */ <0x00 0x01000000 0x00 0x01000000 0x00 0x02330400>, /* First peripheral window */ <0x00 0x08000000 0x00 0x08000000 0x00 0x00200000>, /* Main CPSW */ <0x00 0x0d000000 0x00 0x0d000000 0x00 0x00800000>, /* PCIE_CORE */
@@ -105,6 +91,8 @@ ranges = <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>; /* Peripheral window */ }; }; + + #include "k3-am64-thermal.dtsi" }; /* Now include the peripherals for each bus segments */
arch/arm/dts/k3-am642-evm-u-boot.dtsi +38 -29
99 lines not on this page · raw message
arch/arm/dts/k3-am642-evm.dts +135 -38
359 lines not on this page · raw message
arch/arm/dts/k3-am642-r5-evm.dts +19 -183
265 lines not on this page · raw message
arch/arm/dts/k3-am642-r5-sk.dts +20 -189
259 lines not on this page · raw message
arch/arm/dts/k3-am642-sk-u-boot.dtsi +26 -33
95 lines not on this page · raw message
arch/arm/dts/k3-am642-sk.dts +121 -45
337 lines not on this page · raw message
arch/arm/dts/k3-am642.dtsi +1 -0
@@ -58,6 +58,7 @@ L2_0: l2-cache0 { compatible = "cache"; cache-level = <2>; + cache-unified; cache-size = <0x40000>; cache-line-size = <64>; cache-sets = <256>;
Signature · 1 line
2.34.1
Re: [PATCH v3 4/4] arm: dts: k3-am64: Sync DT with Linux v6.5-rc1
Quoted 9 lines · Roger Quadros
Sync all am642-evm/am642-sk related DT files
with Linux v6.5-rc1.- drop timer1 in favor of
main_timer0inam64-main.dtsi. Need to delete clock & power domain properties ofmain_timer1in-r5.dtselse won't boot. This is becausetimer_initis done duringrproc_startto start System Firmware, but we can't do any clock/power-domain operations before System Firmware starts.
if that is the argument for main_uart0 and main_i2c0 main_gpio0 etc.
- please document in the r5.dts as well as to why we are /delete-property/ power-domains. I think we feed in boardconfig etc by the time we get around to this, correct? if not, we might need to state that information - that without boardconfig being fed to the sysfw pm functions are'nt active.
Otherwise, this is coming along just right.
Quoted 479 lines
- drop cpsw3g custom DT property '
mac_efuse' and custom DT node cpsw-phy-sel as driver picks these from standard property/node.
- include board dts file in -r5 dts file to avoid duplication of nodes. Include-u-boot.dtsion top.
- drop duplicate nodes in -r5 dts and-u-boot.dtsiSigned-off-by Roger Quadros <[email protected]>--- arch/arm/dts/k3-am64-main.dtsi | 171 ++++++++++++++++++++- arch/arm/dts/k3-am64-mcu.dtsi | 53 ++++++- arch/arm/dts/k3-am64-thermal.dtsi | 33 ++++ arch/arm/dts/k3-am64.dtsi | 22 +-- arch/arm/dts/k3-am642-evm-u-boot.dtsi | 67 +++++---- arch/arm/dts/k3-am642-evm.dts | 173 ++++++++++++++++----- arch/arm/dts/k3-am642-r5-evm.dts | 202 +++---------------------- arch/arm/dts/k3-am642-r5-sk.dts | 209 +++----------------------- arch/arm/dts/k3-am642-sk-u-boot.dtsi | 59 ++++---- arch/arm/dts/k3-am642-sk.dts | 166 ++++++++++++++------ arch/arm/dts/k3-am642.dtsi | 1 + 11 files changed, 613 insertions(+), 543 deletions(-) create mode 100644 arch/arm/dts/k3-am64-thermal.dtsiarch/arm/dts/k3-am64-main.dtsi +164
-7@@ -228,12 +228,161 @@ }; }; + main_timer0: timer@2400000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2400000 0x00 0x400>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 36 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 36 1>; + assigned-clock-parents = <&k3_clks 36 2>; + power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer1: timer@2410000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2410000 0x00 0x400>; + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 37 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 37 1>; + assigned-clock-parents = <&k3_clks 37 2>; + power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer2: timer@2420000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2420000 0x00 0x400>; + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 38 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 38 1>; + assigned-clock-parents = <&k3_clks 38 2>; + power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer3: timer@2430000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2430000 0x00 0x400>; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 39 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 39 1>; + assigned-clock-parents = <&k3_clks 39 2>; + power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer4: timer@2440000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2440000 0x00 0x400>; + interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 40 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 40 1>; + assigned-clock-parents = <&k3_clks 40 2>; + power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer5: timer@2450000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2450000 0x00 0x400>; + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 41 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 41 1>; + assigned-clock-parents = <&k3_clks 41 2>; + power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer6: timer@2460000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2460000 0x00 0x400>; + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 42 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 42 1>; + assigned-clock-parents = <&k3_clks 42 2>; + power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer7: timer@2470000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2470000 0x00 0x400>; + interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 43 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 43 1>; + assigned-clock-parents = <&k3_clks 43 2>; + power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer8: timer@2480000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2480000 0x00 0x400>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 44 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 44 1>; + assigned-clock-parents = <&k3_clks 44 2>; + power-domains = <&k3_pds 44 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer9: timer@2490000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2490000 0x00 0x400>; + interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 45 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 45 1>; + assigned-clock-parents = <&k3_clks 45 2>; + power-domains = <&k3_pds 45 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer10: timer@24a0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24a0000 0x00 0x400>; + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 46 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 46 1>; + assigned-clock-parents = <&k3_clks 46 2>; + power-domains = <&k3_pds 46 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer11: timer@24b0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24b0000 0x00 0x400>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 47 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 47 1>; + assigned-clock-parents = <&k3_clks 47 2>; + power-domains = <&k3_pds 47 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_esm: esm@420000 { + compatible = "ti,j721e-esm"; + reg = <0x00 0x420000 0x00 0x1000>; + ti,esm-pins = <160>, <161>; + }; + main_uart0: serial@2800000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x02800000 0x00 0x100>; interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 146 0>; clock-names = "fclk";@@ -245,7 +394,6 @@ reg = <0x00 0x02810000 0x00 0x100>; interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 152 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 152 0>; clock-names = "fclk";@@ -257,7 +405,6 @@ reg = <0x00 0x02820000 0x00 0x100>; interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 153 0>; clock-names = "fclk";@@ -269,7 +416,6 @@ reg = <0x00 0x02830000 0x00 0x100>; interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 154 0>; clock-names = "fclk";@@ -281,7 +427,6 @@ reg = <0x00 0x02840000 0x00 0x100>; interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 155 0>; clock-names = "fclk";@@ -293,7 +438,6 @@ reg = <0x00 0x02850000 0x00 0x100>; interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 156 0>; clock-names = "fclk";@@ -305,7 +449,6 @@ reg = <0x00 0x02860000 0x00 0x100>; interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <48000000>; - current-speed = <115200>; power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 158 0>; clock-names = "fclk";@@ -676,6 +819,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; mailbox0_cluster3: mailbox@29030000 {@@ -686,6 +830,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; mailbox0_cluster4: mailbox@29040000 {@@ -696,6 +841,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; mailbox0_cluster5: mailbox@29050000 {@@ -706,6 +852,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; mailbox0_cluster6: mailbox@29060000 {@@ -715,6 +862,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; mailbox0_cluster7: mailbox@29070000 {@@ -724,6 +872,7 @@ #mbox-cells = <1>; ti,mbox-num-users = <4>; ti,mbox-num-fifos = <16>; + status = "disabled"; }; main_r5fss0: r5fss@78000000 {@@ -1392,4 +1541,12 @@ clock-names = "fck"; status = "disabled"; }; + + main_vtm0: temperature-sensor@b00000 { + compatible = "ti,j7200-vtm"; + reg = <0x00 0xb00000 0x00 0x400>, + <0x00 0xb01000 0x00 0x400>; + power-domains = <&k3_pds 95 TI_SCI_PD_EXCLUSIVE>; + #thermal-sensor-cells = <1>; + }; };arch/arm/dts/k3-am64-mcu.dtsi +51
-2@@ -6,11 +6,55 @@ */ &cbass_mcu { + /* + * The MCU domain timer interrupts are routed only to the ESM module, + * and not currently available for Linux. The MCU domain timers are + * of limited use without interrupts, and likely reserved by the ESM. + */ + mcu_timer0: timer@4800000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x4800000 0x00 0x400>; + clocks = <&k3_clks 35 1>; + clock-names = "fck"; + power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + status = "reserved"; + }; + + mcu_timer1: timer@4810000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x4810000 0x00 0x400>; + clocks = <&k3_clks 48 1>; + clock-names = "fck"; + power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + status = "reserved"; + }; + + mcu_timer2: timer@4820000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x4820000 0x00 0x400>; + clocks = <&k3_clks 49 1>; + clock-names = "fck"; + power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + status = "reserved"; + }; + + mcu_timer3: timer@4830000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x4830000 0x00 0x400>; + clocks = <&k3_clks 50 1>; + clock-names = "fck"; + power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + status = "reserved"; + }; + mcu_uart0: serial@4a00000 { compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x04a00000 0x00 0x100>; interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>; - current-speed = <115200>; power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 149 0>; clock-names = "fclk";@@ -21,7 +65,6 @@ compatible = "ti,am64-uart", "ti,am654-uart"; reg = <0x00 0x04a10000 0x00 0x100>; interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>; - current-speed = <115200>; power-domains = <&k3_pds 160 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 160 0>; clock-names = "fclk";@@ -109,4 +152,10 @@ pinctrl-single,register-width = <32>; pinctrl-single,function-mask = <0xffffffff>; }; + + mcu_esm: esm@4100000 { + compatible = "ti,j721e-esm"; + reg = <0x00 0x4100000 0x00 0x1000>; + ti,esm-pins = <0>, <1>; + }; };arch/arm/dts/k3-am64-thermal.dtsi new file +33
-0@@ -0,0 +1,33 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include <dt-bindings/thermal/thermal.h> + +thermal_zones: thermal-zones { + main0_thermal: main0-thermal { + polling-delay-passive = <250>; /* milliSeconds */ + polling-delay = <500>; /* milliSeconds */ + thermal-sensors = <&main_vtm0 0>; + + trips { + main0_crit: main0-crit { + temperature = <105000>; /* milliCelsius */ + hysteresis = <2000>; /* milliCelsius */ + type = "critical"; + }; + }; + }; + + main1_thermal: main1-thermal { + polling-delay-passive = <250>; /* milliSeconds */ + polling-delay = <500>; /* milliSeconds */ + thermal-sensors = <&main_vtm0 1>; + + trips { + main1_crit: main1-crit { + temperature = <105000>; /* milliCelsius */ + hysteresis = <2000>; /* milliCelsius */ + type = "critical"; + }; + }; + }; +};arch/arm/dts/k3-am64.dtsi +5
-17@@ -8,9 +8,10 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/pinctrl/k3.h> #include <dt-bindings/soc/ti,sci_pm_domain.h> +#include "k3-pinctrl.h" + / { model = "Texas Instruments K3 AM642 SoC"; compatible = "ti,am642";@@ -18,22 +19,6 @@ #address-cells = <2>; #size-cells = <2>; - aliases { - serial0 = &mcu_uart0; - serial1 = &mcu_uart1; - serial2 = &main_uart0; - serial3 = &main_uart1; - serial4 = &main_uart2; - serial5 = &main_uart3; - serial6 = &main_uart4; - serial7 = &main_uart5; - serial8 = &main_uart6; - ethernet0 = &cpsw_port1; - ethernet1 = &cpsw_port2; - mmc0 = &sdhci0; - mmc1 = &sdhci1; - }; - chosen { }; firmware {@@ -69,6 +54,7 @@ <0x00 0x00420000 0x00 0x00420000 0x00 0x00001000>, /* ESM0 */ <0x00 0x00600000 0x00 0x00600000 0x00 0x00001100>, /* GPIO */ <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* Timesync router */ + <0x00 0x00b00000 0x00 0x00b00000 0x00 0x00002400>, /* VTM */ <0x00 0x01000000 0x00 0x01000000 0x00 0x02330400>, /* First peripheral window */ <0x00 0x08000000 0x00 0x08000000 0x00 0x00200000>, /* Main CPSW */ <0x00 0x0d000000 0x00 0x0d000000 0x00 0x00800000>, /* PCIE_CORE */@@ -105,6 +91,8 @@ ranges = <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>; /* Peripheral window */ }; }; + + #include "k3-am64-thermal.dtsi" }; /* Now include the peripherals for each bus segments */arch/arm/dts/k3-am642-evm-u-boot.dtsi +0
-0
arch/arm/dts/k3-am642-evm-u-boot.dtsi line 10
Quoted 3 lines
arch/arm/dts/k3-am642-evm-u-boot.dtsi +0
-0@@ -8,7 +8,7 @@ / { chosen { stdout-path = "serial2:115200n8";
Drop
Quoted 36 lines
arch/arm/dts/k3-am642-evm-u-boot.dtsi +15
-9- tick-timer = &timer1; + tick-timer = &main_timer0; }; memory@80000000 {@@ -16,15 +16,21 @@ }; }; -&cbass_main{ +&vtt_supply { + bootph-pre-ram; +}; + +&cbass_main { bootph-pre-ram; - timer1: timer@2400000 { - compatible = "ti,omap5430-timer"; - reg = <0x0 0x2400000 0x0 0x80>; - ti,timer-alwon; - clock-frequency = <200000000>; - bootph-pre-ram; - }; +}; + +&cbass_mcu { + bootph-pre-ram; +}; + +&main_timer0 { + bootph-pre-ram; + clock-frequency = <200000000>; }; &main_conf {
arch/arm/dts/k3-am642-evm-u-boot.dtsi line 45
Quoted 5 lines
arch/arm/dts/k3-am642-evm-u-boot.dtsi +1
-1@@ -36,21 +42,35 @@ &main_pmx0 { bootph-pre-ram; - main_i2c0_pins_default: main-i2c0-pins-default { + /* FIXME: drop mmc0 pinmux when added to k3-am642-evm.dts */
Actually the kernel dts is correct (also the same in sk.dts in kernel):
Quoted 9 lines
arch/arm/dts/k3-am642-evm-u-boot.dtsi +4
-3+ main_mmc0_pins_default: main-mmc0-pins-default { bootph-pre-ram; pinctrl-single,pins = < - AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */ - AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */ - >; + AM64X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0) /* (B25) MMC0_CLK */ + AM64X_IOPAD(0x01aC, PIN_INPUT_PULLUP, 0) /* (B27) MMC0_CMD */ + AM64X_IOPAD(0x01a4, PIN_INPUT_PULLUP, 0) /* (A26) MMC0_DAT0 */
arch/arm/dts/k3-am642-evm-u-boot.dtsi line 61
Quoted 10 lines
arch/arm/dts/k3-am642-evm-u-boot.dtsi +9
-0+ AM64X_IOPAD(0x01a0, PIN_INPUT_PULLUP, 0) /* (E25) MMC0_DAT1 */ + AM64X_IOPAD(0x019c, PIN_INPUT_PULLUP, 0) /* (C26) MMC0_DAT2 */ + AM64X_IOPAD(0x0198, PIN_INPUT_PULLUP, 0) /* (A25) MMC0_DAT3 */ + AM64X_IOPAD(0x0194, PIN_INPUT_PULLUP, 0) /* (E24) MMC0_DAT4 */ + AM64X_IOPAD(0x0190, PIN_INPUT_PULLUP, 0) /* (A24) MMC0_DAT5 */ + AM64X_IOPAD(0x018c, PIN_INPUT_PULLUP, 0) /* (B26) MMC0_DAT6 */ + AM64X_IOPAD(0x0188, PIN_INPUT_PULLUP, 0) /* (D25) MMC0_DAT7 */ + AM64X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */ + >; };
Please drop this entirely -> If you look at proc schematics
https://www.ti.com/tool/TMDS64GPEVM#design-filesMMC0_CLK is G18, MMC0_DAT0 is K20 and so on. This matches with what we see in
dev.ti.com/sysconfig tool as well and the data sheet - these pins have a single mux mode - that is MMC, no specific register exists for override. infact B25 as a pin does'nt even exist on the package.
you also want to fix the reference in arch/arm/dts/k3-am642-r5-evm.dts
Quoted 436 lines
arch/arm/dts/k3-am642-evm-u-boot.dtsi +9
-16}; +&main_i2c0_pins_default { + bootph-pre-ram; +}; + &main_i2c0 { - status = "okay"; bootph-pre-ram; - pinctrl-names = "default"; - pinctrl-0 = <&main_i2c0_pins_default>; - clock-frequency = <400000>; +}; + +&main_uart0_pins_default { + bootph-pre-ram; }; &main_uart0 {@@ -111,18 +131,7 @@ }; &cpsw3g { - reg = <0x0 0x8000000 0x0 0x200000>, - <0x0 0x43000200 0x0 0x8>; - reg-names = "cpsw_nuss", "mac_efuse"; - /delete-property/ ranges; - pinctrl-0 = <&mdio1_pins_default /* HACK: as MDIO driver is not DM enabled */ - &rgmii1_pins_default - &rgmii2_pins_default>; - - cpsw-phy-sel@04044 { - compatible = "ti,am64-phy-gmii-sel"; - reg = <0x0 0x43004044 0x0 0x8>; - }; + bootph-pre-ram; }; &cpsw_port2 {arch/arm/dts/k3-am642-evm.dts +135
-38@@ -17,15 +17,26 @@ model = "Texas Instruments AM642 EVM"; chosen { - stdout-path = "serial2:115200n8"; - bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; + stdout-path = &main_uart0; + }; + + aliases { + serial0 = &mcu_uart0; + serial1 = &main_uart1; + serial2 = &main_uart0; + serial3 = &main_uart3; + i2c0 = &main_i2c0; + i2c1 = &main_i2c1; + mmc0 = &sdhci0; + mmc1 = &sdhci1; + ethernet0 = &cpsw_port1; + ethernet1 = &cpsw_port2; }; memory@80000000 { device_type = "memory"; /* 2G RAM */ reg = <0x00000000 0x80000000 0x00000000 0x80000000>; - }; reserved-memory {@@ -94,7 +105,7 @@ }; }; - evm_12v0: fixedregulator-evm12v0 { + evm_12v0: regulator-0 { /* main DC jack */ compatible = "regulator-fixed"; regulator-name = "evm_12v0";@@ -104,7 +115,7 @@ regulator-boot-on; }; - vsys_5v0: fixedregulator-vsys5v0 { + vsys_5v0: regulator-1 { /* output of LM5140 */ compatible = "regulator-fixed"; regulator-name = "vsys_5v0";@@ -115,7 +126,7 @@ regulator-boot-on; }; - vsys_3v3: fixedregulator-vsys3v3 { + vsys_3v3: regulator-2 { /* output of LM5140 */ compatible = "regulator-fixed"; regulator-name = "vsys_3v3";@@ -126,7 +137,7 @@ regulator-boot-on; }; - vdd_mmc1: fixed-regulator-sd { + vdd_mmc1: regulator-3 { /* TPS2051BD */ compatible = "regulator-fixed"; regulator-name = "vdd_mmc1";@@ -138,7 +149,7 @@ gpio = <&exp1 6 GPIO_ACTIVE_HIGH>; }; - vddb: fixedregulator-vddb { + vddb: regulator-4 { compatible = "regulator-fixed"; regulator-name = "vddb_3v3_display"; regulator-min-microvolt = <3300000>;@@ -148,6 +159,20 @@ regulator-boot-on; }; + vtt_supply: regulator-5 { + compatible = "regulator-fixed"; + regulator-name = "vtt"; + pinctrl-names = "default"; + pinctrl-0 = <&ddr_vtt_pins_default>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&main_gpio0 12 GPIO_ACTIVE_HIGH>; + vin-supply = <&vsys_3v3>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + }; + leds { compatible = "gpio-leds";@@ -201,7 +226,7 @@ }; &main_pmx0 { - main_mmc1_pins_default: main-mmc1-pins-default { + main_mmc1_pins_default: main-mmc1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */ AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */@@ -215,7 +240,16 @@ >; }; - main_uart0_pins_default: main-uart0-pins-default { + main_uart1_pins_default: main-uart1-default-pins { + pinctrl-single,pins = < + AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */ + AM64X_IOPAD(0x024c, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */ + AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */ + AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */ + >; + }; + + main_uart0_pins_default: main-uart0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */ AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */@@ -224,7 +258,7 @@ >; }; - main_spi0_pins_default: main-spi0-pins-default { + main_spi0_pins_default: main-spi0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0210, PIN_INPUT, 0) /* (D13) SPI0_CLK */ AM64X_IOPAD(0x0208, PIN_OUTPUT, 0) /* (D12) SPI0_CS0 */@@ -233,21 +267,28 @@ >; }; - main_i2c1_pins_default: main-i2c1-pins-default { + main_i2c0_pins_default: main-i2c0-default-pins { + pinctrl-single,pins = < + AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */ + AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */ + >; + }; + + main_i2c1_pins_default: main-i2c1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */ AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */ >; }; - mdio1_pins_default: mdio1-pins-default { + mdio1_pins_default: mdio1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ >; }; - rgmii1_pins_default: rgmii1-pins-default { + rgmii1_pins_default: rgmii1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x01cc, PIN_INPUT, 4) /* (W5) PRG0_PRU1_GPO7.RGMII1_RD0 */ AM64X_IOPAD(0x01d4, PIN_INPUT, 4) /* (Y5) PRG0_PRU1_GPO9.RGMII1_RD1 */@@ -264,7 +305,7 @@ >; }; - rgmii2_pins_default: rgmii2-pins-default { + rgmii2_pins_default: rgmii2-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */ AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */@@ -281,13 +322,13 @@ >; }; - main_usb0_pins_default: main-usb0-pins-default { + main_usb0_pins_default: main-usb0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ >; }; - ospi0_pins_default: ospi0-pins-default { + ospi0_pins_default: ospi0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0000, PIN_OUTPUT, 0) /* (N20) OSPI0_CLK */ AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* (L19) OSPI0_CSn0 */@@ -303,36 +344,58 @@ >; }; - main_ecap0_pins_default: main-ecap0-pins-default { + main_ecap0_pins_default: main-ecap0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0270, PIN_INPUT, 0) /* (D18) ECAP0_IN_APWM_OUT */ >; }; - main_mcan0_pins_default: main-mcan0-pins-default { + main_mcan0_pins_default: main-mcan0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0254, PIN_INPUT, 0) /* (B17) MCAN0_RX */ AM64X_IOPAD(0x0250, PIN_OUTPUT, 0) /* (A17) MCAN0_TX */ >; }; - main_mcan1_pins_default: main-mcan1-pins-default { + main_mcan1_pins_default: main-mcan1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x025c, PIN_INPUT, 0) /* (D17) MCAN1_RX */ AM64X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (C17) MCAN1_TX */ >; }; + + ddr_vtt_pins_default: ddr-vtt-default-pins { + pinctrl-single,pins = < + AM64X_IOPAD(0x0030, PIN_OUTPUT_PULLUP, 7) /* (L18) OSPI0_CSN1.GPIO0_12 */ + >; + }; }; &main_uart0 { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&main_uart0_pins_default>; + current-speed = <115200>; }; /* main_uart1 is reserved for firmware usage */ &main_uart1 { status = "reserved"; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart1_pins_default>; +}; + +&main_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; + + eeprom@50 { + /* AT24CM01 */ + compatible = "atmel,24c1024"; + reg = <0x50>; + }; }; &main_i2c1 {@@ -425,8 +488,7 @@ &cpsw3g { pinctrl-names = "default"; - pinctrl-0 = <&rgmii1_pins_default - &rgmii2_pins_default>; + pinctrl-0 = <&rgmii1_pins_default>, <&rgmii2_pins_default>; }; &cpsw_port1 {@@ -471,10 +533,53 @@ cdns,tchsh-ns = <60>; cdns,tslch-ns = <60>; cdns,read-delay = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ospi.tiboot3"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + label = "ospi.tispl"; + reg = <0x100000 0x200000>; + }; + + partition@300000 { + label = "ospi.u-boot"; + reg = <0x300000 0x400000>; + }; + + partition@700000 { + label = "ospi.env"; + reg = <0x700000 0x40000>; + }; + + partition@740000 { + label = "ospi.env.backup"; + reg = <0x740000 0x40000>; + }; + + partition@800000 { + label = "ospi.rootfs"; + reg = <0x800000 0x37c0000>; + }; + + partition@3fc0000 { + label = "ospi.phypattern"; + reg = <0x3fc0000 0x40000>; + }; + }; }; }; &mailbox0_cluster2 { + status = "okay"; + mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>;@@ -486,11 +591,9 @@ }; }; -&mailbox0_cluster3 { - status = "disabled"; -}; - &mailbox0_cluster4 { + status = "okay"; + mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>;@@ -502,41 +605,35 @@ }; }; -&mailbox0_cluster5 { - status = "disabled"; -}; - &mailbox0_cluster6 { + status = "okay"; + mbox_m4_0: mbox-m4-0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>; }; }; -&mailbox0_cluster7 { - status = "disabled"; -}; - &main_r5fss0_core0 { - mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core0>; + mboxes = <&mailbox0_cluster2>, <&mbox_main_r5fss0_core0>; memory-region = <&main_r5fss0_core0_dma_memory_region>, <&main_r5fss0_core0_memory_region>; }; &main_r5fss0_core1 { - mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core1>; + mboxes = <&mailbox0_cluster2>, <&mbox_main_r5fss0_core1>; memory-region = <&main_r5fss0_core1_dma_memory_region>, <&main_r5fss0_core1_memory_region>; }; &main_r5fss1_core0 { - mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core0>; + mboxes = <&mailbox0_cluster4>, <&mbox_main_r5fss1_core0>; memory-region = <&main_r5fss1_core0_dma_memory_region>, <&main_r5fss1_core0_memory_region>; }; &main_r5fss1_core1 { - mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core1>; + mboxes = <&mailbox0_cluster4>, <&mbox_main_r5fss1_core1>; memory-region = <&main_r5fss1_core1_dma_memory_region>, <&main_r5fss1_core1_memory_region>; };arch/arm/dts/k3-am642-r5-evm.dts +2
-4@@ -1,19 +1,17 @@ // SPDX-License-Identifier: GPL-2.0 /* - * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ + * Copyright (C) 2020-2023 Texas Instruments Incorporated - https://www.ti.com/ */ -/dts-v1/; - -#include "k3-am642.dtsi" +#include "k3-am642-evm.dts" #include "k3-am64-evm-ddr4-1600MTs.dtsi"
arch/arm/dts/k3-am642-r5-evm.dts line 15
Quoted 10 lines
arch/arm/dts/k3-am642-r5-evm.dts +2
-2#include "k3-am64-ddr.dtsi" -#include "k3-am64x-binman.dtsi" + +#include "k3-am642-evm-u-boot.dtsi" / { chosen { stdout-path = "serial2:115200n8"; - tick-timer = &timer1; };
Drop the entire chosen - comes in from u-boot.dtsi
Quoted 18 lines
arch/arm/dts/k3-am642-r5-evm.dts +0
-8aliases {@@ -21,14 +19,6 @@ remoteproc1 = &a53_0; }; - memory@80000000 { - device_type = "memory"; - /* 2G RAM */ - reg = <0x00000000 0x80000000 0x00000000 0x80000000>; - - bootph-pre-ram; - }; - a53_0: a53@0 { compatible = "ti,am654-rproc"; reg = <0x00 0x00a90000 0x00 0x10>;
arch/arm/dts/k3-am642-r5-evm.dts line 38
Quoted 3 lines
arch/arm/dts/k3-am642-r5-evm.dts +0
-0@@ -46,34 +36,12 @@ bootph-pre-ram; };
Can you also look at the &memory_controller {
} node?
I think vtt_supply already points to the DDR vtt pinmux? so, a bit confused why we would point the pinctrl-0 to the same pinmux again?
Quoted 245 lines
arch/arm/dts/k3-am642-r5-evm.dts +15
-169- reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - - secure_ddr: optee@9e800000 { - reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ - alignment = <0x1000>; - no-map; - }; - }; - clk_200mhz: dummy-clock-200mhz { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <200000000>; bootph-pre-ram; }; - - vtt_supply: vtt-supply { - compatible = "regulator-gpio"; - regulator-name = "vtt"; - regulator-min-microvolt = <0>; - regulator-max-microvolt = <3300000>; - gpios = <&main_gpio0 12 GPIO_ACTIVE_HIGH>; - states = <0 0x0 3300000 0x1>; - bootph-pre-ram; - }; }; &cbass_main {@@ -85,131 +53,12 @@ }; }; -&cbass_main { - main_esm: esm@420000 { - compatible = "ti,j721e-esm"; - reg = <0x0 0x420000 0x0 0x1000>; - ti,esm-pins = <160>, <161>; - bootph-pre-ram; - }; -}; - -&cbass_mcu { +&main_esm { bootph-pre-ram; - mcu_esm: esm@4100000 { - compatible = "ti,j721e-esm"; - reg = <0x0 0x4100000 0x0 0x1000>; - ti,esm-pins = <0>, <1>; - bootph-pre-ram; - }; }; -&main_pmx0 { +&mcu_esm { bootph-pre-ram; - main_uart0_pins_default: main-uart0-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */ - AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */ - AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */ - AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */ - >; - }; - - main_uart1_pins_default: main-uart1-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */ - AM64X_IOPAD(0x024c, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */ - AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */ - AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */ - >; - }; - - main_mmc0_pins_default: main-mmc0-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0) /* (B25) MMC0_CLK */ - AM64X_IOPAD(0x01aC, PIN_INPUT_PULLUP, 0) /* (B27) MMC0_CMD */ - AM64X_IOPAD(0x01a4, PIN_INPUT_PULLUP, 0) /* (A26) MMC0_DAT0 */ - AM64X_IOPAD(0x01a0, PIN_INPUT_PULLUP, 0) /* (E25) MMC0_DAT1 */ - AM64X_IOPAD(0x019c, PIN_INPUT_PULLUP, 0) /* (C26) MMC0_DAT2 */ - AM64X_IOPAD(0x0198, PIN_INPUT_PULLUP, 0) /* (A25) MMC0_DAT3 */ - AM64X_IOPAD(0x0194, PIN_INPUT_PULLUP, 0) /* (E24) MMC0_DAT4 */ - AM64X_IOPAD(0x0190, PIN_INPUT_PULLUP, 0) /* (A24) MMC0_DAT5 */ - AM64X_IOPAD(0x018c, PIN_INPUT_PULLUP, 0) /* (B26) MMC0_DAT6 */ - AM64X_IOPAD(0x0188, PIN_INPUT_PULLUP, 0) /* (D25) MMC0_DAT7 */ - AM64X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */ - >; - }; - - main_mmc1_pins_default: main-mmc1-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */ - AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */ - AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */ - AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */ - AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */ - AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */ - AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */ - AM64X_IOPAD(0x029c, PIN_INPUT_PULLUP, 0) /* (C20) MMC1_SDWP */ - >; - }; - - ddr_vtt_pins_default: ddr-vtt-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0030, PIN_OUTPUT_PULLUP, 7) /* (L18) OSPI0_CSN1.GPIO0_12 */ - >; - }; - - main_usb0_pins_default: main-usb0-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ - >; - }; - - mdio1_pins_default: mdio1-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ - AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ - >; - }; - - rgmii1_pins_default: rgmii1-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x01cc, PIN_INPUT, 4) /* (W5) PRG0_PRU1_GPO7.RGMII1_RD0 */ - AM64X_IOPAD(0x01d4, PIN_INPUT, 4) /* (Y5) PRG0_PRU1_GPO9.RGMII1_RD1 */ - AM64X_IOPAD(0x01d8, PIN_INPUT, 4) /* (V6) PRG0_PRU1_GPO10.RGMII1_RD2 */ - AM64X_IOPAD(0x01f4, PIN_INPUT, 4) /* (V5) PRG0_PRU1_GPO17.RGMII1_RD3 */ - AM64X_IOPAD(0x0188, PIN_INPUT, 4) /* (AA5) PRG0_PRU0_GPO10.RGMII1_RXC */ - AM64X_IOPAD(0x0184, PIN_INPUT, 4) /* (W6) PRG0_PRU0_GPO9.RGMII1_RX_CTL */ - AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */ - AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */ - AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */ - AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */ - AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */ - AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */ - >; - }; - - rgmii2_pins_default: rgmii2-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */ - AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */ - AM64X_IOPAD(0x0110, PIN_INPUT, 4) /* (AA12) PRG1_PRU1_GPO2.RGMII2_RD2 */ - AM64X_IOPAD(0x0114, PIN_INPUT, 4) /* (Y12) PRG1_PRU1_GPO3.RGMII2_RD3 */ - AM64X_IOPAD(0x0120, PIN_INPUT, 4) /* (U11) PRG1_PRU1_GPO6.RGMII2_RXC */ - AM64X_IOPAD(0x0118, PIN_INPUT, 4) /* (W12) PRG1_PRU1_GPO4.RGMII2_RX_CTL */ - AM64X_IOPAD(0x0134, PIN_OUTPUT, 4) /* (AA10) PRG1_PRU1_GPO11.RGMII2_TD0 */ - AM64X_IOPAD(0x0138, PIN_OUTPUT, 4) /* (V10) PRG1_PRU1_GPO12.RGMII2_TD1 */ - AM64X_IOPAD(0x013c, PIN_OUTPUT, 4) /* (U10) PRG1_PRU1_GPO13.RGMII2_TD2 */ - AM64X_IOPAD(0x0140, PIN_OUTPUT, 4) /* (AA11) PRG1_PRU1_GPO14.RGMII2_TD3 */ - AM64X_IOPAD(0x0148, PIN_OUTPUT, 4) /* (Y10) PRG1_PRU1_GPO16.RGMII2_TXC */ - AM64X_IOPAD(0x0144, PIN_OUTPUT, 4) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */ - >; - }; }; &dmsc {@@ -225,15 +74,6 @@ /delete-property/ power-domains; /delete-property/ clocks; /delete-property/ clock-names; - pinctrl-names = "default"; - pinctrl-0 = <&main_uart0_pins_default>; - status = "okay"; -}; - -&main_uart1 { - bootph-pre-ram; - pinctrl-names = "default"; - pinctrl-0 = <&main_uart1_pins_default>; }; &memorycontroller {@@ -246,8 +86,7 @@ /delete-property/ power-domains; clocks = <&clk_200mhz>; clock-names = "clk_xin"; - ti,driver-strength-ohm = <50>; - disable-wp; + /* FIXME: drop pinctrl-0 when added to k3-am642-evm.dts */ pinctrl-0 = <&main_mmc0_pins_default>; };@@ -255,9 +94,6 @@ /delete-property/ power-domains; clocks = <&clk_200mhz>; clock-names = "clk_xin"; - ti,driver-strength-ohm = <50>; - disable-wp; - pinctrl-0 = <&main_mmc1_pins_default>; }; &main_gpio0 {@@ -270,16 +106,16 @@ /delete-property/ power-domains; }; -&usbss0 { - ti,vbus-divider; - ti,usb2-only; -}; - -&usb0 { - dr_mode = "otg"; - maximum-speed = "high-speed"; - pinctrl-names = "default"; - pinctrl-0 = <&main_usb0_pins_default>; +/* timer init is called as part of rproc_start() while + * starting System Firmware, so any clock/power-domain + * operations will fail as SYSFW is not yet up and running. + * Delete all clock/power-domain properties to avoid + * timer init failure. + * This is an always on timer at 20MHz. + */ +&main_timer0 { + /delete-property/ clocks; + /delete-property/ assigned-clocks; + /delete-property/ assigned-clock-parents; + /delete-property/ power-domains; }; - -#include "k3-am642-evm-u-boot.dtsi"arch/arm/dts/k3-am642-r5-sk.dts +1
-6@@ -3,19 +3,15 @@ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ */ -/dts-v1/; - -#include <dt-bindings/mux/ti-serdes.h> -#include <dt-bindings/phy/phy.h> -#include <dt-bindings/net/ti-dp83867.h> -#include "k3-am642.dtsi" +#include "k3-am642-sk.dts"
arch/arm/dts/k3-am642-r5-sk.dts line 15
Quoted 10 lines
arch/arm/dts/k3-am642-r5-sk.dts +2
-1#include "k3-am64-sk-lp4-1600MTs.dtsi" #include "k3-am64-ddr.dtsi" +#include "k3-am642-sk-u-boot.dtsi" + / { chosen { stdout-path = "serial2:115200n8"; - tick-timer = &timer1; };
Drop entire chosen?
Quoted 37 lines
arch/arm/dts/k3-am642-r5-sk.dts +0
-19aliases {@@ -23,13 +19,6 @@ remoteproc1 = &a53_0; }; - memory@80000000 { - device_type = "memory"; - /* 2G RAM */ - reg = <0x00000000 0x80000000 0x00000000 0x80000000>; - bootph-pre-ram; - }; - a53_0: a53@0 { compatible = "ti,am654-rproc"; reg = <0x00 0x00a90000 0x00 0x10>;@@ -47,18 +36,6 @@ bootph-pre-ram; }; - reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - - secure_ddr: optee@9e800000 { - reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ - alignment = <0x1000>; - no-map; - }; - }; - clk_200mhz: dummy-clock-200mhz { compatible = "fixed-clock"; #clock-cells = <0>;@@ -76,110 +53,6 @@ };
arch/arm/dts/k3-am642-r5-sk.dts line 86
Quoted 10 lines
arch/arm/dts/k3-am642-r5-sk.dts +0
-8}; -&cbass_main { - main_esm: esm@420000 { - compatible = "ti,j721e-esm"; - reg = <0x0 0x420000 0x0 0x1000>; - ti,esm-pins = <160>, <161>; - bootph-pre-ram; - }; -};
please add for r5-sk:
&main_esm {
bootph-pre-ram;
};&mcu_esm {
bootph-pre-ram;
};Quoted 672 lines
arch/arm/dts/k3-am642-r5-sk.dts +17
-155- -&cbass_mcu { - bootph-pre-ram; - mcu_esm: esm@4100000 { - compatible = "ti,j721e-esm"; - reg = <0x0 0x4100000 0x0 0x1000>; - ti,esm-pins = <0>, <1>; - bootph-pre-ram; - }; -}; - -&main_pmx0 { - bootph-pre-ram; - main_uart0_pins_default: main-uart0-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */ - AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */ - AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */ - AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */ - >; - }; - - main_uart1_pins_default: main-uart1-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */ - AM64X_IOPAD(0x024c, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */ - AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */ - AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */ - >; - }; - - main_mmc1_pins_default: main-mmc1-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */ - AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */ - AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */ - AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */ - AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */ - AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */ - AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */ - AM64X_IOPAD(0x029c, PIN_INPUT_PULLUP, 0) /* (C20) MMC1_SDWP */ - >; - }; - - main_usb0_pins_default: main-usb0-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ - >; - }; - - mdio1_pins_default: mdio1-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ - AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ - >; - }; - - rgmii1_pins_default: rgmii1-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x011c, PIN_INPUT, 4) /* (AA13) PRG1_PRU1_GPO5.RGMII1_RD0 */ - AM64X_IOPAD(0x0128, PIN_INPUT, 4) /* (U12) PRG1_PRU1_GPO8.RGMII1_RD1 */ - AM64X_IOPAD(0x0150, PIN_INPUT, 4) /* (Y13) PRG1_PRU1_GPO18.RGMII1_RD2 */ - AM64X_IOPAD(0x0154, PIN_INPUT, 4) /* (V12) PRG1_PRU1_GPO19.RGMII1_RD3 */ - AM64X_IOPAD(0x00d8, PIN_INPUT, 4) /* (W13) PRG1_PRU0_GPO8.RGMII1_RXC */ - AM64X_IOPAD(0x00cc, PIN_INPUT, 4) /* (V13) PRG1_PRU0_GPO5.RGMII1_RX_CTL */ - AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */ - AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */ - AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */ - AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */ - AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */ - AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */ - >; - }; - - rgmii2_pins_default: rgmii2-pins-default { - pinctrl-single,pins = < - AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */ - AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */ - AM64X_IOPAD(0x0110, PIN_INPUT, 4) /* (AA12) PRG1_PRU1_GPO2.RGMII2_RD2 */ - AM64X_IOPAD(0x0114, PIN_INPUT, 4) /* (Y12) PRG1_PRU1_GPO3.RGMII2_RD3 */ - AM64X_IOPAD(0x0120, PIN_INPUT, 4) /* (U11) PRG1_PRU1_GPO6.RGMII2_RXC */ - AM64X_IOPAD(0x0118, PIN_INPUT, 4) /* (W12) PRG1_PRU1_GPO4.RGMII2_RX_CTL */ - AM64X_IOPAD(0x0134, PIN_OUTPUT, 4) /* (AA10) PRG1_PRU1_GPO11.RGMII2_TD0 */ - AM64X_IOPAD(0x0138, PIN_OUTPUT, 4) /* (V10) PRG1_PRU1_GPO12.RGMII2_TD1 */ - AM64X_IOPAD(0x013c, PIN_OUTPUT, 4) /* (U10) PRG1_PRU1_GPO13.RGMII2_TD2 */ - AM64X_IOPAD(0x0140, PIN_OUTPUT, 4) /* (AA11) PRG1_PRU1_GPO14.RGMII2_TD3 */ - AM64X_IOPAD(0x0148, PIN_OUTPUT, 4) /* (Y10) PRG1_PRU1_GPO16.RGMII2_TXC */ - AM64X_IOPAD(0x0144, PIN_OUTPUT, 4) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */ - >; - }; -}; - &dmsc { mboxes= <&secure_proxy_main 0>, <&secure_proxy_main 1>,@@ -189,79 +62,37 @@ ti,secure-host; }; +/* EEPROM might be read before SYSFW is available */ +&main_i2c0 { + /delete-property/ power-domains; +}; + &main_uart0 { /delete-property/ power-domains; /delete-property/ clocks; /delete-property/ clock-names; - pinctrl-names = "default"; - pinctrl-0 = <&main_uart0_pins_default>; - status = "okay"; -}; - -&main_uart1 { - bootph-pre-ram; - pinctrl-names = "default"; - pinctrl-0 = <&main_uart1_pins_default>; }; &sdhci1 { /delete-property/ power-domains; clocks = <&clk_200mhz>; clock-names = "clk_xin"; - ti,driver-strength-ohm = <50>; - disable-wp; - pinctrl-0 = <&main_mmc1_pins_default>; -}; - -&serdes_ln_ctrl { - idle-states = <AM64_SERDES0_LANE0_USB>; }; &serdes_wiz0 { status = "okay"; }; -&serdes0 { - serdes0_usb_link: link@0 { - reg = <0>; - cdns,num-lanes = <1>; - #phy-cells = <0>; - cdns,phy-type = <PHY_TYPE_USB3>; - resets = <&serdes_wiz0 1>; - }; -}; - -&usbss0 { - ti,vbus-divider; -}; - -&usb0 { - dr_mode = "host"; - maximum-speed = "super-speed"; - pinctrl-names = "default"; - pinctrl-0 = <&main_usb0_pins_default>; - phys = <&serdes0_usb_link>; - phy-names = "cdns3,usb3-phy"; -}; - -&cpsw3g { - pinctrl-names = "default"; - pinctrl-0 = <&mdio1_pins_default - &rgmii1_pins_default - &rgmii2_pins_default>; -}; - -&cpsw_port2 { - phy-mode = "rgmii-rxid"; - phy-handle = <&cpsw3g_phy1>; -}; - -&cpsw3g_mdio { - cpsw3g_phy1: ethernet-phy@1 { - reg = <1>; - ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; - ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; - }; +/* timer init is called as part of rproc_start() while + * starting System Firmware, so any clock/power-domain + * operations will fail as SYSFW is not yet up and running. + * Delete all clock/power-domain properties to avoid + * timer init failure. + * This is an always on timer at 20MHz. + */ +&main_timer0 { + /delete-property/ clocks; + /delete-property/ assigned-clocks; + /delete-property/ assigned-clock-parents; + /delete-property/ power-domains; }; - -#include "k3-am642-sk-u-boot.dtsi"arch/arm/dts/k3-am642-sk-u-boot.dtsi +26
-33@@ -8,11 +8,7 @@ / { chosen { stdout-path = "serial2:115200n8"; - tick-timer = &timer1; - }; - - aliases { - mmc1 = &sdhci1; + tick-timer = &main_timer0; }; memory@80000000 {@@ -22,13 +18,23 @@ &cbass_main{ bootph-pre-ram; - timer1: timer@2400000 { - compatible = "ti,omap5430-timer"; - reg = <0x0 0x2400000 0x0 0x80>; - ti,timer-alwon; - clock-frequency = <200000000>; - bootph-pre-ram; - }; +}; + +&main_esm { + bootph-pre-ram; +}; + +&cbass_mcu { + bootph-pre-ram; +}; + +&mcu_esm { + bootph-pre-ram; +}; + +&main_timer0 { + bootph-pre-ram; + clock-frequency = <200000000>; }; &main_conf {@@ -40,20 +46,18 @@ &main_pmx0 { bootph-pre-ram; - main_i2c0_pins_default: main-i2c0-pins-default { - bootph-pre-ram; - pinctrl-single,pins = < - AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */ - AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */ - >; - }; +}; + +&main_i2c0_pins_default { + bootph-pre-ram; }; &main_i2c0 { bootph-pre-ram; - pinctrl-names = "default"; - pinctrl-0 = <&main_i2c0_pins_default>; - clock-frequency = <400000>; +}; + +&main_uart0_pins_default { + bootph-pre-ram; }; &main_uart0 {@@ -102,18 +106,8 @@ }; &cpsw3g { - reg = <0x0 0x8000000 0x0 0x200000>, - <0x0 0x43000200 0x0 0x8>; - reg-names = "cpsw_nuss", "mac_efuse"; - /delete-property/ ranges; bootph-pre-ram; - cpsw-phy-sel@04044 { - compatible = "ti,am64-phy-gmii-sel"; - reg = <0x0 0x43004044 0x0 0x8>; - bootph-pre-ram; - }; - ethernet-ports { bootph-pre-ram; };@@ -160,7 +154,6 @@ }; &usb0 { - dr_mode = "host"; bootph-pre-ram; };arch/arm/dts/k3-am642-sk.dts +121
-45@@ -17,15 +17,25 @@ model = "Texas Instruments AM642 SK"; chosen { - stdout-path = "serial2:115200n8"; - bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; + stdout-path = &main_uart0; + }; + + aliases { + serial0 = &mcu_uart0; + serial1 = &main_uart1; + serial2 = &main_uart0; + i2c0 = &main_i2c0; + i2c1 = &main_i2c1; + mmc0 = &sdhci0; + mmc1 = &sdhci1; + ethernet0 = &cpsw_port1; + ethernet1 = &cpsw_port2; }; memory@80000000 { device_type = "memory"; /* 2G RAM */ reg = <0x00000000 0x80000000 0x00000000 0x80000000>; - }; reserved-memory {@@ -94,7 +104,7 @@ }; }; - vusb_main: fixed-regulator-vusb-main5v0 { + vusb_main: regulator-0 { /* USB MAIN INPUT 5V DC */ compatible = "regulator-fixed"; regulator-name = "vusb_main5v0";@@ -104,7 +114,7 @@ regulator-boot-on; }; - vcc_3v3_sys: fixedregulator-vcc-3v3-sys { + vcc_3v3_sys: regulator-1 { /* output of LP8733xx */ compatible = "regulator-fixed"; regulator-name = "vcc_3v3_sys";@@ -115,7 +125,7 @@ regulator-boot-on; }; - vdd_mmc1: fixed-regulator-sd { + vdd_mmc1: regulator-2 { /* TPS2051BD */ compatible = "regulator-fixed"; regulator-name = "vdd_mmc1";@@ -127,7 +137,7 @@ gpio = <&exp1 3 GPIO_ACTIVE_HIGH>; }; - com8_ls_en: regulator-1 { + com8_ls_en: regulator-3 { compatible = "regulator-fixed"; regulator-name = "com8_ls_en"; regulator-min-microvolt = <3300000>;@@ -139,7 +149,7 @@ gpio = <&main_gpio0 62 GPIO_ACTIVE_LOW>; }; - wlan_en: regulator-2 { + wlan_en: regulator-4 { /* output of SN74AVC4T245RSVR */ compatible = "regulator-fixed"; regulator-name = "wlan_en";@@ -222,20 +232,21 @@ }; &main_pmx0 { - main_mmc1_pins_default: main-mmc1-pins-default { + main_mmc1_pins_default: main-mmc1-default-pins { pinctrl-single,pins = < - AM64X_IOPAD(0x0294, PIN_INPUT, 0) /* (J19) MMC1_CMD */ + AM64X_IOPAD(0x029c, PIN_INPUT_PULLUP, 0) /* (C20) MMC1_SDWP */ + AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */ + AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */ AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* (#N/A) MMC1_CLKLB */ - AM64X_IOPAD(0x028c, PIN_INPUT, 0) /* (L20) MMC1_CLK */ - AM64X_IOPAD(0x0288, PIN_INPUT, 0) /* (K21) MMC1_DAT0 */ - AM64X_IOPAD(0x0284, PIN_INPUT, 0) /* (L21) MMC1_DAT1 */ - AM64X_IOPAD(0x0280, PIN_INPUT, 0) /* (K19) MMC1_DAT2 */ - AM64X_IOPAD(0x027c, PIN_INPUT, 0) /* (K18) MMC1_DAT3 */ - AM64X_IOPAD(0x0298, PIN_INPUT, 0) /* (D19) MMC1_SDCD */ + AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */ + AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */ + AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */ + AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */ + AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */ >; }; - main_uart0_pins_default: main-uart0-pins-default { + main_uart0_pins_default: main-uart0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */ AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */@@ -244,27 +255,43 @@ >; }; - main_usb0_pins_default: main-usb0-pins-default { + main_uart1_pins_default: main-uart1-default-pins { + pinctrl-single,pins = < + AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */ + AM64X_IOPAD(0x024c, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */ + AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */ + AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */ + >; + }; + + main_usb0_pins_default: main-usb0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ >; }; - main_i2c1_pins_default: main-i2c1-pins-default { + main_i2c0_pins_default: main-i2c0-default-pins { + pinctrl-single,pins = < + AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */ + AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */ + >; + }; + + main_i2c1_pins_default: main-i2c1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */ AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */ >; }; - mdio1_pins_default: mdio1-pins-default { + mdio1_pins_default: mdio1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ >; }; - rgmii1_pins_default: rgmii1-pins-default { + rgmii1_pins_default: rgmii1-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x011c, PIN_INPUT, 4) /* (AA13) PRG1_PRU1_GPO5.RGMII1_RD0 */ AM64X_IOPAD(0x0128, PIN_INPUT, 4) /* (U12) PRG1_PRU1_GPO8.RGMII1_RD1 */@@ -281,7 +308,7 @@ >; }; - rgmii2_pins_default: rgmii2-pins-default { + rgmii2_pins_default: rgmii2-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */ AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */@@ -298,7 +325,7 @@ >; }; - ospi0_pins_default: ospi0-pins-default { + ospi0_pins_default: ospi0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0000, PIN_OUTPUT, 0) /* (N20) OSPI0_CLK */ AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* (L19) OSPI0_CSn0 */@@ -314,24 +341,24 @@ >; }; - main_ecap0_pins_default: main-ecap0-pins-default { + main_ecap0_pins_default: main-ecap0-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x0270, PIN_INPUT, 0) /* (D18) ECAP0_IN_APWM_OUT */ >; }; - main_wlan_en_pins_default: main-wlan-en-pins-default { + main_wlan_en_pins_default: main-wlan-en-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x00c4, PIN_OUTPUT_PULLUP, 7) /* (V8) GPIO0_48 */ >; }; - main_com8_ls_en_pins_default: main-com8-ls-en-pins-default { + main_com8_ls_en_pins_default: main-com8-ls-en-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x00fc, PIN_OUTPUT, 7) /* (U7) PRG1_PRU0_GPO17.GPIO0_62 */ >; }; - main_wlan_pins_default: main-wlan-pins-default { + main_wlan_pins_default: main-wlan-default-pins { pinctrl-single,pins = < AM64X_IOPAD(0x00bc, PIN_INPUT, 7) /* (U8) GPIO0_46 */ >;@@ -342,11 +369,26 @@ status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&main_uart0_pins_default>; + current-speed = <115200>; }; &main_uart1 { /* main_uart1 is reserved for firmware usage */ status = "reserved"; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart1_pins_default>; +}; + +&main_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; + + eeprom@51 { + compatible = "atmel,24c512"; + reg = <0x51>; + }; }; &main_i2c1 {@@ -439,8 +481,7 @@ &cpsw3g { pinctrl-names = "default"; - pinctrl-0 = <&rgmii1_pins_default - &rgmii2_pins_default>; + pinctrl-0 = <&rgmii1_pins_default>, <&rgmii2_pins_default>; }; &cpsw_port1 {@@ -490,10 +531,53 @@ cdns,tchsh-ns = <60>; cdns,tslch-ns = <60>; cdns,read-delay = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ospi.tiboot3"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + label = "ospi.tispl"; + reg = <0x100000 0x200000>; + }; + + partition@300000 { + label = "ospi.u-boot"; + reg = <0x300000 0x400000>; + }; + + partition@700000 { + label = "ospi.env"; + reg = <0x700000 0x40000>; + }; + + partition@740000 { + label = "ospi.env.backup"; + reg = <0x740000 0x40000>; + }; + + partition@800000 { + label = "ospi.rootfs"; + reg = <0x800000 0x37c0000>; + }; + + partition@3fc0000 { + label = "ospi.phypattern"; + reg = <0x3fc0000 0x40000>; + }; + }; }; }; &mailbox0_cluster2 { + status = "okay"; + mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>;@@ -505,11 +589,9 @@ }; }; -&mailbox0_cluster3 { - status = "disabled"; -}; - &mailbox0_cluster4 { + status = "okay"; + mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>;@@ -521,41 +603,35 @@ }; }; -&mailbox0_cluster5 { - status = "disabled"; -}; - &mailbox0_cluster6 { + status = "okay"; + mbox_m4_0: mbox-m4-0 { ti,mbox-rx = <0 0 2>; ti,mbox-tx = <1 0 2>; }; }; -&mailbox0_cluster7 { - status = "disabled"; -}; - &main_r5fss0_core0 { - mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core0>; + mboxes = <&mailbox0_cluster2>, <&mbox_main_r5fss0_core0>; memory-region = <&main_r5fss0_core0_dma_memory_region>, <&main_r5fss0_core0_memory_region>; }; &main_r5fss0_core1 { - mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core1>; + mboxes = <&mailbox0_cluster2>, <&mbox_main_r5fss0_core1>; memory-region = <&main_r5fss0_core1_dma_memory_region>, <&main_r5fss0_core1_memory_region>; }; &main_r5fss1_core0 { - mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core0>; + mboxes = <&mailbox0_cluster4>, <&mbox_main_r5fss1_core0>; memory-region = <&main_r5fss1_core0_dma_memory_region>, <&main_r5fss1_core0_memory_region>; }; &main_r5fss1_core1 { - mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core1>; + mboxes = <&mailbox0_cluster4>, <&mbox_main_r5fss1_core1>; memory-region = <&main_r5fss1_core1_dma_memory_region>, <&main_r5fss1_core1_memory_region>; };arch/arm/dts/k3-am642.dtsi +1
-0@@ -58,6 +58,7 @@ L2_0: l2-cache0 { compatible = "cache"; cache-level = <2>; + cache-unified; cache-size = <0x40000>; cache-line-size = <64>; cache-sets = <256>;Signature · 1 line
2.34.1
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH v3 4/4] arm: dts: k3-am64: Sync DT with Linux v6.5-rc1
Hi Nishanth,
Quoted 45 lines · Nishanth Menon
Quoted 9 lines · Roger Quadros
Sync all am642-evm/am642-sk related DT files
with Linux v6.5-rc1.- drop timer1 in favor of
main_timer0inam64-main.dtsi. Need to delete clock & power domain properties ofmain_timer1in-r5.dtselse won't boot. This is becausetimer_initis done duringrproc_startto start System Firmware, but we can't do any clock/power-domain operations before System Firmware starts.if that is the argument for
main_uart0andmain_i2c0main_gpio0etc.
- please document in ther5.dtsas well as to why we are /delete-property/ power-domains. I think we feed in boardconfig etc by the time we get around to this, correct? if not, we might need to state that information - that without boardconfig being fed to the sysfw pm functions are'nt active.Otherwise, this is coming along just right.
Quoted 24 lines
- drop cpsw3g custom DT property '
mac_efuse' and custom DT node cpsw-phy-sel as driver picks these from standard property/node.
- include board dts file in -r5 dts file to avoid duplication of nodes. Include-u-boot.dtsion top.
- drop duplicate nodes in -r5 dts and-u-boot.dtsiSigned-off-by Roger Quadros <[email protected]>--- arch/arm/dts/k3-am64-main.dtsi | 171 ++++++++++++++++++++- arch/arm/dts/k3-am64-mcu.dtsi | 53 ++++++- arch/arm/dts/k3-am64-thermal.dtsi | 33 ++++ arch/arm/dts/k3-am64.dtsi | 22 +-- arch/arm/dts/k3-am642-evm-u-boot.dtsi | 67 +++++---- arch/arm/dts/k3-am642-evm.dts | 173 ++++++++++++++++----- arch/arm/dts/k3-am642-r5-evm.dts | 202 +++---------------------- arch/arm/dts/k3-am642-r5-sk.dts | 209 +++----------------------- arch/arm/dts/k3-am642-sk-u-boot.dtsi | 59 ++++---- arch/arm/dts/k3-am642-sk.dts | 166 ++++++++++++++------ arch/arm/dts/k3-am642.dtsi | 1 + 11 files changed, 613 insertions(+), 543 deletions(-) create mode 100644 arch/arm/dts/k3-am64-thermal.dtsiarch/arm/dts/k3-am64-main.dtsi +0
-0
<snip>
Quoted 54 lines
Quoted 16 lines
arch/arm/dts/k3-am642-r5-evm.dts +2
-4@@ -1,19 +1,17 @@ // SPDX-License-Identifier: GPL-2.0 /* - * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ + * Copyright (C) 2020-2023 Texas Instruments Incorporated - https://www.ti.com/ */ -/dts-v1/; - -#include "k3-am642.dtsi" +#include "k3-am642-evm.dts" #include "k3-am64-evm-ddr4-1600MTs.dtsi"arch/arm/dts/k3-am642-r5-evm.dts line 15
Quoted 10 lines
arch/arm/dts/k3-am642-r5-evm.dts +2
-2#include "k3-am64-ddr.dtsi" -#include "k3-am64x-binman.dtsi" + +#include "k3-am642-evm-u-boot.dtsi" / { chosen { stdout-path = "serial2:115200n8"; - tick-timer = &timer1; };Drop the entire chosen - comes in from
u-boot.dtsiQuoted 18 lines
arch/arm/dts/k3-am642-r5-evm.dts +0
-8aliases {@@ -21,14 +19,6 @@ remoteproc1 = &a53_0; }; - memory@80000000 { - device_type = "memory"; - /* 2G RAM */ - reg = <0x00000000 0x80000000 0x00000000 0x80000000>; - - bootph-pre-ram; - }; - a53_0: a53@0 { compatible = "ti,am654-rproc"; reg = <0x00 0x00a90000 0x00 0x10>;arch/arm/dts/k3-am642-r5-evm.dts line 38
Quoted 3 lines
arch/arm/dts/k3-am642-r5-evm.dts +0
-0@@ -46,34 +36,12 @@ bootph-pre-ram; };Can you also look at the
&memory_controller{
} node?
Quoted 3 lines
I think
vtt_supplyalready points to the DDR vtt pinmux? so, a bit confused why we would point the pinctrl-0 to the same pinmux again?
Right. Also vtt_supply is always-on fixed regulator. So will drop vtt-supply property from memory_controller node.
<snip>
Quoted 19 lines
Quoted 19 lines
arch/arm/dts/k3-am642-r5-evm.dts +0
-1-#include "k3-am642-evm-u-boot.dtsi"arch/arm/dts/k3-am642-r5-sk.dts +1
-6@@ -3,19 +3,15 @@ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ */ -/dts-v1/; - -#include <dt-bindings/mux/ti-serdes.h> -#include <dt-bindings/phy/phy.h> -#include <dt-bindings/net/ti-dp83867.h> -#include "k3-am642.dtsi" +#include "k3-am642-sk.dts" #include "k3-am64-sk-lp4-1600MTs.dtsi" #include "k3-am64-ddr.dtsi"
Quoted 8 lines
arch/arm/dts/k3-am642-r5-sk.dts line 15
Quoted 7 lines
arch/arm/dts/k3-am642-r5-sk.dts +2
-1+#include "k3-am642-sk-u-boot.dtsi" + / { chosen { stdout-path = "serial2:115200n8"; - tick-timer = &timer1; };Drop entire chosen?
OK.
Quoted 50 lines
Quoted 38 lines
arch/arm/dts/k3-am642-r5-sk.dts +0
-19aliases {@@ -23,13 +19,6 @@ remoteproc1 = &a53_0; }; - memory@80000000 { - device_type = "memory"; - /* 2G RAM */ - reg = <0x00000000 0x80000000 0x00000000 0x80000000>; - bootph-pre-ram; - }; - a53_0: a53@0 { compatible = "ti,am654-rproc"; reg = <0x00 0x00a90000 0x00 0x10>;@@ -47,18 +36,6 @@ bootph-pre-ram; }; - reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - - secure_ddr: optee@9e800000 { - reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ - alignment = <0x1000>; - no-map; - }; - }; - clk_200mhz: dummy-clock-200mhz { compatible = "fixed-clock"; #clock-cells = <0>;@@ -76,110 +53,6 @@ };arch/arm/dts/k3-am642-r5-sk.dts line 86
Quoted 10 lines
arch/arm/dts/k3-am642-r5-sk.dts +0
-8}; -&cbass_main { - main_esm: esm@420000 { - compatible = "ti,j721e-esm"; - reg = <0x0 0x420000 0x0 0x1000>; - ti,esm-pins = <160>, <161>; - bootph-pre-ram; - }; -};please add for r5-sk:
Quoted 8 lines
&main_esm { bootph-pre-ram; };&mcu_esm { bootph-pre-ram; };
I added them in -u-boot.dtsi along with cbass_main and cbass_mcu. Should I move them to -r5-sk instead?
<snip>
Signature · 2 lines
cheers, -roger
Re: [PATCH v3 4/4] arm: dts: k3-am64: Sync DT with Linux v6.5-rc1
In reply to Nishanth MenonQuoted 11 lines · Nishanth Menon
Quoted 9 lines · Roger Quadros
Sync all am642-evm/am642-sk related DT files
with Linux v6.5-rc1.- drop timer1 in favor of
main_timer0inam64-main.dtsi. Need to delete clock & power domain properties ofmain_timer1in-r5.dtselse won't boot. This is becausetimer_initis done duringrproc_startto start System Firmware, but we can't do any clock/power-domain operations before System Firmware starts.
Quoted 7 lines
if that is the argument for
main_uart0andmain_i2c0main_gpio0etc.
- please document in ther5.dtsas well as to why we are /delete-property/ power-domains. I think we feed in boardconfig etc by the time we get around to this, correct? if not, we might need to state that information - that without boardconfig being fed to the sysfw pm functions are'nt active.
I got rid of /delete-property/ for main_i2c0 and main_gpio0 and didn't see any ill effects. So will drop them from there. Looks like we need to have it only for main_uart0 and main_timer0. I'll add a comment for main_uart0.
Signature · 2 lines
cheers, -roger