tools/perf/tests: perf all metrics test fails when perf_event access is restricted
PATCH v2 1/2 tools/perf/tests: perf all metrics test fails when perf_event access is restricted
Perf all metrics test fails as below when perf_event access is restricted.
./perf test -v "perf all metrics test"
Metric 'Memory_RD_BW_Chip' not printed in:
Error:
Access to performance monitoring and observability operations is limited. Enforced MAC policy settings (SELinux) can limit access to performance —
access to performance monitoring and observability operations for processes without CAP_PERFMON, CAP_SYS_PTRACE or CAP_SYS_ADMIN Linux capability. —
test child finished with -1
---- end ----
perf all metrics test: FAILED!
The perf all metrics test picks the input events from "perf list --raw-dump metrics" and runs "perf stat -M "$m"" for each of the metrics in the list. It fails here for some of the metrics which needs access, since it collects system wide resource details/statistics. Fix the testcase to skip those metric events. The check is added at two places:
- When metric is run for workload monitoring
- when metric is run for system wide.
It could happen that some of the metric events are not valid in per-thread mode. Example from an x86 system:
$ ./perf stat -M smi_cycles true
Error:
Invalid event (msr/smi/u) in per-thread mode, enable system wide with '-a'.The test fallbacks to system wide if first stage fails. But when run with system wide for this metric, it hits the issue with access restriction.
$ ./perf stat -M smi_cycles -a sleep 0.1
Error:
Access to performance monitoring and observability operations is limited.Similar some events report not supported while running with system wide.
Example from an x86 system:
$ ./perf stat -M tma_info_system_socket_clks -a sleep 0.1
Performance counter stats for 'system wide':
<not supported> cbox_0/event=0x0/u
0.102633747 seconds time elapsedHence the checks for unsupported events and access restrictions is added for both cases.
---
Changelog:
v1 -> v2:
Added the check for access restriction in workload as well as system wide check.
tools/perf/tests/shell/stat_all_metrics.sh | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
tools/perf/tests/shell/stat_all_metrics.sh +3 -3
@@ -1,18 +1,18 @@ #!/bin/bash # perf all metrics test # SPDX-License-Identifier: GPL-2.0 - err=0 +//list="tma_info_system_socket_clks" for m in $(perf list --raw-dump metrics); do echo "Testing $m" result=$(perf stat -M "$m" true 2>&1) - if [[ "$result" =~ ${m:0:50} ]] || [[ "$result" =~ "<not supported>" ]] + if [[ "$result" =~ ${m:0:50} ]] || [[ "$result" =~ "<not supported>" ]] || [[ "$result" =~ "Access to performance monitoring and observability operations is limited" ]] then continue fi # Failed so try system wide. result=$(perf stat -M "$m" -a sleep 0.01 2>&1) - if [[ "$result" =~ ${m:0:50} ]] + if [[ "$result" =~ ${m:0:50} ]] || [[ "$result" =~ "<not supported>" ]] || [[ "$result" =~ "Access to performance monitoring and observability operations is limited" ]] then continue fi
Signature · 1 line
2.31.1
PATCH v2 2/2 tools/perf/tests: perf all metricgroups test fails when perf_event access is restricted
Perf all metricgroups test fails as below when perf_event access is restricted.
./perf test -v "perf all metricgroups test"
Testing Memory_BW
Error:
Access to performance monitoring and observability operations is limited. Enforced MAC policy settings (SELinux) can limit access to performance access to performance monitoring and observability operations for processes without CAP_PERFMON, CAP_SYS_PTRACE or CAP_SYS_ADMIN Linux capability.
test child finished with -1
---- end ----
perf all metricgroups test: FAILED!
Fix the testcase to skip those metric events which needs perf_event access explicitly. The exit code of the testcase is based on return code of the perf stat command ( enabled by set -e option ). Hence save the exit status in a variable and use that to decide success or fail for the testcase.
---
Changelog:
v1 -> v2:
Changed the condition to use "echo" and "grep" so it works on Posix shell as well.
tools/perf/tests/shell/stat_all_metricgroups.sh | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-)
tools/perf/tests/shell/stat_all_metricgroups.sh +11 -3
@@ -2,11 +2,19 @@ # perf all metricgroups test # SPDX-License-Identifier: GPL-2.0 -set -e - for m in $(perf list --raw-dump metricgroups); do echo "Testing $m" - perf stat -M "$m" -a true + result=$(perf stat -M "$m" -a true 2>&1) + rc=$? + # Skip if there is no access to perf_events monitoring + # Otherwise exit based on the return code of perf comamnd. + if echo "$result" | grep -q "Access to performance monitoring and observability operations is limited"; + then + continue + else + [ $rc -ne 0 ] && exit $rc + fi + done exit 0
Signature · 1 line
2.31.1
Re: [PATCH V2 2/2] tools/perf/tests: perf all metricgroups test fails when perf_event access is restricted
Quoted 15 lines · Athira Rajeev
Perf all metricgroups test fails as below when
perf_eventaccess is restricted../perf test -v "perf all metricgroups test"
TestingMemory_BW
Error:
Access to performance monitoring and observability operations is limited. Enforced MAC policy settings (SELinux) can limit access to performance access to performance monitoring and observability operations for processes withoutCAP_PERFMON,CAP_SYS_PTRACEorCAP_SYS_ADMINLinux capability.test child finished with -1
---- end ----
perf all metricgroups test: FAILED!
Quoted 7 lines
Fix the testcase to skip those metric events which needs
perf_eventaccess explicitly. The exit code of the testcase is based on return code of the perf stat command ( enabled by set -e option ). Hence save the exit status in a variable and use that to decide success or fail for the testcase.Signed-off-by Athira Rajeev<[email protected]>
With this patch applied(on power) perf metricgroups test works correctly when perf_event access is restricted.
# ./perf test "perf all metricgroups test" 96: perf all metricgroups test : Ok
Quoted 36 lines
---
Changelog:
v1 -> v2:
Changed the condition to use "echo" and "grep" so it works on Posix shell as well.tools/perf/tests/shell/stat_all_metricgroups.sh | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-)tools/perf/tests/shell/stat_all_metricgroups.sh +11
-3@@ -2,11 +2,19 @@ # perf all metricgroups test # SPDX-License-Identifier: GPL-2.0 -set -e - for m in $(perf list --raw-dump metricgroups); do echo "Testing $m" - perf stat -M "$m" -a true + result=$(perf stat -M "$m" -a true 2>&1) + rc=$? + # Skip if there is no access to perf_events monitoring + # Otherwise exit based on the return code of perf comamnd. + if echo "$result" | grep -q "Access to performance monitoring and observability operations is limited"; + then + continue + else + [ $rc -ne 0 ] && exit $rc + fi + done exit 0
Arnaldo Carvalho de Melo
maintainerRe: [PATCH V2 2/2] tools/perf/tests: perf all metricgroups test fails when perf_event access is restricted
Em Mon, Aug 07, 2023 at 08:14:39PM +0530, Disha Goel escreveu:
Quoted 16 lines · Athira Rajeev
Quoted 15 lines
Perf all metricgroups test fails as below when
perf_eventaccess is restricted../perf test -v "perf all metricgroups test"
TestingMemory_BW
Error:
Access to performance monitoring and observability operations is limited. Enforced MAC policy settings (SELinux) can limit access to performance access to performance monitoring and observability operations for processes withoutCAP_PERFMON,CAP_SYS_PTRACEorCAP_SYS_ADMINLinux capability.test child finished with -1
---- end ----
perf all metricgroups test: FAILED!
Quoted 5 lines
Quoted 5 lines
Fix the testcase to skip those metric events which needs
perf_eventaccess explicitly. The exit code of the testcase is based on return code of the perf stat command ( enabled by set -e option ). Hence save the exit status in a variable and use that to decide success or fail for the testcase.
I wonder if we shouldn't somehow check if the credentials needed to performing a test shouldn't be checked before trying it. This way we would check if the check that the tool or the kernel is doing is the appropriate one.
I.e. the kernel refusal for doing something may be an error.
- Arnaldo
Quoted 45 lines
Quoted 1 line
Signed-off-by Athira Rajeev<[email protected]>With this patch applied(on power) perf metricgroups test works correctly when
perf_eventaccess is restricted.# ./perf test "perf all metricgroups test" 96: perf all metricgroups test : OkTested-by Disha Goel<[email protected]>Quoted 36 lines
---
Changelog:
v1 -> v2:
Changed the condition to use "echo" and "grep" so it works on Posix shell as well.tools/perf/tests/shell/stat_all_metricgroups.sh | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-)tools/perf/tests/shell/stat_all_metricgroups.sh +11
-3@@ -2,11 +2,19 @@ # perf all metricgroups test # SPDX-License-Identifier: GPL-2.0 -set -e - for m in $(perf list --raw-dump metricgroups); do echo "Testing $m" - perf stat -M "$m" -a true + result=$(perf stat -M "$m" -a true 2>&1) + rc=$? + # Skip if there is no access to perf_events monitoring + # Otherwise exit based on the return code of perf comamnd. + if echo "$result" | grep -q "Access to performance monitoring and observability operations is limited"; + then + continue + else + [ $rc -ne 0 ] && exit $rc + fi + done exit 0
Signature · 1 line
- Arnaldo