usb: gadget: ether: Inline functions used once
PATCH v5 1/3 usb: gadget: ether: Inline functions used once
These functions here are only ever called once since drop of non-DM networking code. Inline them. No functional change.
---
Cc: Kevin Hilman <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Miquel Raynal <[email protected]>
Cc: Simon Glass <[email protected]>
---
V2: No change
V3: No change
V4: No change
V5: No change
--- drivers/usb/gadget/ether.c | 48 +++++++------------------------------- 1 file changed, 9 insertions(+), 39 deletions(-)
drivers/usb/gadget/ether.c +9 -39
@@ -2273,10 +2273,11 @@ fail: }/*-------------------------------------------------------------------------*/ -static void _usb_eth_halt (struct ether_priv *priv); +static void usb_eth_stop (struct udevice *dev); -static int _usb_eth_init (struct ether_priv *priv) +static int usb_eth_start (struct udevice *udev) { +struct ether_priv *priv =dev_get_priv (udev);struct eth_dev *dev = &priv->ethdev;struct usb_gadget *gadget;unsigned long ts;
@@ -2347,12 +2348,13 @@ static int _usb_eth_init(struct ether_priv *priv)rx_submit (dev, dev->rx_req,0 );return 0 ; fail: -_usb_eth_halt (priv); +usb_eth_stop (udev);return -1 ; } -static int _usb_eth_send (struct ether_priv *priv,void *packet,int length) +static int usb_eth_send (struct udevice *udev,void *packet,int length) { +struct ether_priv *priv =dev_get_priv (udev);int retval;void *rndis_pkt =NULL ;struct eth_dev *dev = &priv->ethdev;
@@ -2419,15 +2421,9 @@ drop:return -ENOMEM ; } -static int _usb_eth_recv (struct ether_priv *priv) -{ -usb_gadget_handle_interrupts (0 ); - -return 0 ; -} - -static void _usb_eth_halt (struct ether_priv *priv) +static void usb_eth_stop (struct udevice *udev) { +struct ether_priv *priv =dev_get_priv (udev);struct eth_dev *dev = &priv->ethdev;/* If the gadget not registered, simple return */
@@ -2459,31 +2455,12 @@ static void _usb_eth_halt(struct ether_priv *priv)usb_gadget_release (0 ); } -static int usb_eth_start (struct udevice *dev) -{ -struct ether_priv *priv =dev_get_priv (dev); - -return _usb_eth_init (priv); -} - -static int usb_eth_send (struct udevice *dev,void *packet,int length) -{ -struct ether_priv *priv =dev_get_priv (dev); - -return _usb_eth_send (priv, packet, length); -} -static int usb_eth_recv (struct udevice *dev,int flags,uchar **packetp) {struct ether_priv *priv =dev_get_priv (dev);struct eth_dev *ethdev = &priv->ethdev; -int ret; - ret =_usb_eth_recv (priv); -if (ret) { -pr_err ("error packet receive\n" ); -return ret; - } +usb_gadget_handle_interrupts (0 );if (packet_received) {if (ethdev->rx_req) {
@@ -2509,13 +2486,6 @@ static int usb_eth_free_pkt(struct udevice *dev, uchar *packet,return rx_submit (ethdev, ethdev->rx_req,0 ); } -static void usb_eth_stop (struct udevice *dev) -{ -struct ether_priv *priv =dev_get_priv (dev); - -_usb_eth_halt (priv); -} -static int usb_eth_probe (struct udevice *dev) {struct ether_priv *priv =dev_get_priv (dev);
Signature · 1 line
2.40.1
PATCH v5 2/3 usb: gadget: ether: Move probe function above driver structure
Move the driver probe function above the driver structure, so it can be placed alongside other related functions, like upcoming remove function. No functional change.
---
Cc: Kevin Hilman <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Miquel Raynal <[email protected]>
Cc: Simon Glass <[email protected]>
---
V2: No change
V3: No change
V4: No change
V5: No change
--- drivers/usb/gadget/ether.c | 28 ++++++++++++++-------------- 1 file changed, 14 insertions(+), 14 deletions(-)
drivers/usb/gadget/ether.c +14 -14
@@ -2486,20 +2486,6 @@ static int usb_eth_free_pkt(struct udevice *dev, uchar *packet,return rx_submit (ethdev, ethdev->rx_req,0 ); } -static int usb_eth_probe (struct udevice *dev) -{ -struct ether_priv *priv =dev_get_priv (dev); -struct eth_pdata *pdata =dev_get_plat (dev); - - priv->netdev = dev; - l_priv = priv; - -get_ether_addr (CONFIG_USBNET_DEV_ADDR , pdata->enetaddr); -eth_env_set_enetaddr ("usbnet_devaddr" , pdata->enetaddr); - -return 0 ; -} -static const struct eth_ops usb_eth_ops = { .start = usb_eth_start, .send = usb_eth_send,
@@ -2528,6 +2514,20 @@ int usb_ether_init(void)return 0 ; } +static int usb_eth_probe (struct udevice *dev) +{ +struct ether_priv *priv =dev_get_priv (dev); +struct eth_pdata *pdata =dev_get_plat (dev); + + priv->netdev = dev; + l_priv = priv; + +get_ether_addr (CONFIG_USBNET_DEV_ADDR , pdata->enetaddr); +eth_env_set_enetaddr ("usbnet_devaddr" , pdata->enetaddr); + +return 0 ; +} +U_BOOT_DRIVER (eth_usb) = { .name ="usb_ether" , .id =UCLASS_ETH ,
Signature · 1 line
2.40.1
Re: [PATCH v5 2/3] usb: gadget: ether: Move probe function above driver structure
Quoted 5 lines · Marek Vasut
Move the driver probe function above the driver structure, so it can be placed alongside other related functions, like upcoming remove function. No functional change.
Signed-off-by Marek Vasut <[email protected]>
Signature · 1 line
Tom
Re: [PATCH v5 2/3] usb: gadget: ether: Move probe function above driver structure
In reply to Marek VasutHi Marek,
[email protected] wrote on Fri, 4 Aug 2023 17:41:10 +0200:
Quoted 11 lines
Move the driver probe function above the driver structure, so it can be placed alongside other related functions, like upcoming remove function. No functional change.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Kevin Hilman <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Miquel Raynal <[email protected]>
Cc: Simon Glass <[email protected]>
---
Thanks,
Miquèl
Re: [PATCH v5 2/3] usb: gadget: ether: Move probe function above driver structure
In reply to Marek VasutHi Marek,
[email protected] wrote on Fri, 4 Aug 2023 17:41:10 +0200:
Quoted 11 lines
Move the driver probe function above the driver structure, so it can be placed alongside other related functions, like upcoming remove function. No functional change.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Kevin Hilman <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Miquel Raynal <[email protected]>
Cc: Simon Glass <[email protected]>
---
Thanks,
Miquèl
Re: [PATCH v5 2/3] usb: gadget: ether: Move probe function above driver structure
In reply to Marek VasutQuoted 8 lines · Marek Vasut
Move the driver probe function above the driver structure, so it can be placed alongside other related functions, like upcoming remove function. No functional change.
Signed-off-by Marek Vasut <[email protected]>Tested-by Tom Rini <[email protected]>Tested-by Miquel Raynal <[email protected]>Tested-by Miquel Raynal <[email protected]>
Signature · 1 line
Tom
PATCH v5 3/3 usb: gadget: ether: Handle gadget driver registration in probe and remove
In reply to Marek VasutMove the ethernet gadget driver registration and removal from ethernet bind and unbind callbacks into driver DM probe and remove callbacks. This way, when the driver is bound, which is triggered deliberately using 'bind' command, the USB ethernet gadget driver is instantiated and bound to the matching UDC. In reverse, when the driver is unbound, which is again triggered deliberately using 'unbind' command, the USB ethernet gadget driver instance is removed.
Effectively, this now behaves like running either 'ums' or 'dfu' or any other commands utilizing USB gadget functionality.
This also drops use of usb_gadget_release() and moves the use of usb_gadget_initialize() into usb_ether_init() used only by legacy platforms that do not use 'bind' command properly yet. Those have no place in drivers.
---
NOTE: This must be thoroughly tested.
---
Cc: Kevin Hilman <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Miquel Raynal <[email protected]>
Cc: Simon Glass <[email protected]>
---
V2: Fix up return value handling in probe
V3: Reinstate usb_gadget_initialize() in usb_ether_init() to retain
this obscure workaround for legacy platforms that fail to use bind command
V4: Call usb_gadget_release() in unbind callback to further help
legacy platforms
V5: No change
--- drivers/usb/gadget/ether.c | 97 ++++++++++++++++++++------------------ 1 file changed, 52 insertions(+), 45 deletions(-)
drivers/usb/gadget/ether.c +52 -45
@@ -2281,49 +2281,8 @@ static int usb_eth_start(struct udevice *udev)struct eth_dev *dev = &priv->ethdev;struct usb_gadget *gadget;unsigned long ts; -int ret;unsigned long timeout =USB_CONNECT_TIMEOUT ; - ret =usb_gadget_initialize (0 ); -if (ret) -return ret; - -/* Configure default mac-addresses for the USB ethernet device */ -#ifdef CONFIG_USBNET_DEV_ADDR -strlcpy (dev_addr,CONFIG_USBNET_DEV_ADDR ,sizeof (dev_addr)); -#endif -#ifdef CONFIG_USBNET_HOST_ADDR -strlcpy (host_addr,CONFIG_USBNET_HOST_ADDR ,sizeof (host_addr)); -#endif -/* Check if the user overruled the MAC addresses */ -if (env_get ("usbnet_devaddr" )) -strlcpy (dev_addr,env_get ("usbnet_devaddr" ), -sizeof (dev_addr)); - -if (env_get ("usbnet_hostaddr" )) -strlcpy (host_addr,env_get ("usbnet_hostaddr" ), -sizeof (host_addr)); - -if (!is_eth_addr_valid (dev_addr)) { -pr_err ("Need valid 'usbnet_devaddr' to be set" ); - goto fail; - } -if (!is_eth_addr_valid (host_addr)) { -pr_err ("Need valid 'usbnet_hostaddr' to be set" ); - goto fail; - } - - priv->eth_driver.speed =DEVSPEED ; - priv->eth_driver.bind = eth_bind; - priv->eth_driver.unbind = eth_unbind; - priv->eth_driver.setup = eth_setup; - priv->eth_driver.reset = eth_disconnect; - priv->eth_driver.disconnect = eth_disconnect; - priv->eth_driver.suspend = eth_suspend; - priv->eth_driver.resume = eth_resume; -if (usb_gadget_register_driver (&priv->eth_driver) <0 ) - goto fail; - dev->network_started =0 ; packet_received =0 ;
@@ -2450,9 +2409,6 @@ static void usb_eth_stop(struct udevice *udev)usb_gadget_handle_interrupts (0 ); dev->network_started =0 ; } - -usb_gadget_unregister_driver (&priv->eth_driver); -usb_gadget_release (0 ); }static int usb_eth_recv (struct udevice *dev,int flags,uchar **packetp)
@@ -2511,7 +2467,7 @@ int usb_ether_init(void)return ret; } -return 0 ; +return usb_gadget_initialize (0 ); }static int usb_eth_probe (struct udevice *dev)
@@ -2525,6 +2481,55 @@ static int usb_eth_probe(struct udevice *dev)get_ether_addr (CONFIG_USBNET_DEV_ADDR , pdata->enetaddr);eth_env_set_enetaddr ("usbnet_devaddr" , pdata->enetaddr); +/* Configure default mac-addresses for the USB ethernet device */ +#ifdef CONFIG_USBNET_DEV_ADDR +strlcpy (dev_addr,CONFIG_USBNET_DEV_ADDR ,sizeof (dev_addr)); +#endif +#ifdef CONFIG_USBNET_HOST_ADDR +strlcpy (host_addr,CONFIG_USBNET_HOST_ADDR ,sizeof (host_addr)); +#endif +/* Check if the user overruled the MAC addresses */ +if (env_get ("usbnet_devaddr" )) +strlcpy (dev_addr,env_get ("usbnet_devaddr" ), +sizeof (dev_addr)); + +if (env_get ("usbnet_hostaddr" )) +strlcpy (host_addr,env_get ("usbnet_hostaddr" ), +sizeof (host_addr)); + +if (!is_eth_addr_valid (dev_addr)) { +pr_err ("Need valid 'usbnet_devaddr' to be set" ); +return -EINVAL ; + } +if (!is_eth_addr_valid (host_addr)) { +pr_err ("Need valid 'usbnet_hostaddr' to be set" ); +return -EINVAL ; + } + + priv->eth_driver.speed =DEVSPEED ; + priv->eth_driver.bind = eth_bind; + priv->eth_driver.unbind = eth_unbind; + priv->eth_driver.setup = eth_setup; + priv->eth_driver.reset = eth_disconnect; + priv->eth_driver.disconnect = eth_disconnect; + priv->eth_driver.suspend = eth_suspend; + priv->eth_driver.resume = eth_resume; +return usb_gadget_register_driver (&priv->eth_driver); +} + +static int usb_eth_remove (struct udevice *dev) +{ +struct ether_priv *priv =dev_get_priv (dev); + +usb_gadget_unregister_driver (&priv->eth_driver); + +return 0 ; +} + +static int usb_eth_unbind (struct udevice *dev) +{ +usb_gadget_release (0 ); +return 0 ; }
@@ -2532,6 +2537,8 @@ U_BOOT_DRIVER(eth_usb) = { .name = "usb_ether", .id = UCLASS_ETH, .probe = usb_eth_probe, + .remove = usb_eth_remove, + .unbind = usb_eth_unbind, .ops = &usb_eth_ops, .priv_auto = sizeof(struct ether_priv), .plat_auto = sizeof(struct eth_pdata),
Signature · 1 line
2.40.1
PATCH 1/1 cmd: Enable BIND by default if we have USB_ETHER
The nature of the network stack means that if we are going to use the gadget mode USB network driver there's no easy path to implicitly bind/unbind the driver. Enable the "bind" command by default here so that we can bind/unbind this as needed.
---
Cc: Marek Vasut <[email protected]>
Cc: Miquel Raynal <[email protected]>
--- cmd/Kconfig | 1 + 1 file changed, 1 insertion(+)
cmd/Kconfig +1 -0
@@ -986,6 +986,7 @@ config CMD_BCB config CMD_BIND bool "bind/unbind - Bind or unbind a device to/from a driver" depends on DM + default y if USB_ETHER help Bind or unbind a device to/from a driver from the command line. This is useful in situations where a device may be handled by several
Signature · 1 line
2.34.1
Re: [PATCH] cmd: Enable BIND by default if we have USB_ETHER
Hi Tom,
[email protected] wrote on Fri, 4 Aug 2023 12:06:21 -0400:
Quoted 9 lines
The nature of the network stack means that if we are going to use the gadget mode USB network driver there's no easy path to implicitly bind/unbind the driver. Enable the "bind" command by default here so that we can bind/unbind this as needed.
Signed-off-by Tom Rini <[email protected]>---
Cc: Marek Vasut <[email protected]>
Cc: Miquel Raynal <[email protected]>
Thanks,
Miquèl
Re: [PATCH v5 3/3] usb: gadget: ether: Handle gadget driver registration in probe and remove
In reply to Marek VasutQuoted 11 lines · Marek Vasut
Move the ethernet gadget driver registration and removal from ethernet bind and unbind callbacks into driver DM probe and remove callbacks. This way, when the driver is bound, which is triggered deliberately using 'bind' command, the USB ethernet gadget driver is instantiated and bound to the matching UDC. In reverse, when the driver is unbound, which is again triggered deliberately using 'unbind' command, the USB ethernet gadget driver instance is removed.
Effectively, this now behaves like running either 'ums' or 'dfu' or any other commands utilizing USB gadget functionality.
Quoted 6 lines
This also drops use of
usb_gadget_release()and moves the use ofusb_gadget_initialize()intousb_ether_init()used only by legacy platforms that do not use 'bind' command properly yet. Those have no place in drivers.Signed-off-by Marek Vasut <[email protected]>
Signature · 1 line
Tom
Re: [PATCH v5 3/3] usb: gadget: ether: Handle gadget driver registration in probe and remove
In reply to Marek VasutQuoted 11 lines · Marek Vasut
Move the ethernet gadget driver registration and removal from ethernet bind and unbind callbacks into driver DM probe and remove callbacks. This way, when the driver is bound, which is triggered deliberately using 'bind' command, the USB ethernet gadget driver is instantiated and bound to the matching UDC. In reverse, when the driver is unbound, which is again triggered deliberately using 'unbind' command, the USB ethernet gadget driver instance is removed.
Effectively, this now behaves like running either 'ums' or 'dfu' or any other commands utilizing USB gadget functionality.
Quoted 7 lines
This also drops use of
usb_gadget_release()and moves the use ofusb_gadget_initialize()intousb_ether_init()used only by legacy platforms that do not use 'bind' command properly yet. Those have no place in drivers.Signed-off-by Marek Vasut <[email protected]>Tested-by Tom Rini <[email protected]>
Signature · 1 line
Tom
Quoted 4 lines · Marek Vasut
These functions here are only ever called once since drop of non-DM networking code. Inline them. No functional change.
Signed-off-by Marek Vasut <[email protected]>
Signature · 1 line
Tom
Hi Marek,
[email protected] wrote on Fri, 4 Aug 2023 17:41:09 +0200:
Quoted 10 lines
These functions here are only ever called once since drop of non-DM networking code. Inline them. No functional change.
Signed-off-by Marek Vasut <[email protected]>---
Cc: Kevin Hilman <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Miquel Raynal <[email protected]>
Cc: Simon Glass <[email protected]>
---
Thanks,
Miquèl
Quoted 6 lines · Marek Vasut
These functions here are only ever called once since drop of non-DM networking code. Inline them. No functional change.
Signed-off-by Marek Vasut <[email protected]>Tested-by Tom Rini <[email protected]>Tested-by Miquel Raynal <[email protected]>
Signature · 1 line
Tom