Skip to contentSkip to conversation

sunxi: Orange Pi Zero 3 DT support

PATCH Applied Andre Przywara 2 participants 10 messages Aug 4, 2023 – Aug 6, 2023

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v2 cover sunxi: Orange Pi Zero 3 DT support

Hi,

quick update of the series, mostly cosmetic fixes, except for the regulator range. For a changelog, see below.

==================
Orange Pi recently released the Orange Pi Zero 3 board, which is some updated version of their former Zero 2 development board. Some component changes (Motorcomm PHY instead of Realtek, different PMIC), some board layout changes, and it ships with up to 4GB of DRAM now. The SoC is now labelled H618 instead of H616, which apparently is the same, just with more L2 cache.

Split the existing OPi Zero2 DT, to allow sharing most DT nodes, then add the binding documentation and DT for the new board.

Linux v6.5-rc boots out of the box (the PMIC driver just made it in), and most things work: UART, PSCI, GPIO, SPI flash, SD card, USB. Ethernet is somewhat working: I get an IP address via DHCP, and can for instance start SSH, but it hangs at some point. I suspect some PHY setup problem, though others have it working. Help or advice welcome.

Cheers,
Andre

Changelog v1 .. v2:
- rename common .dtsi file to sun50i-h616-orangepi-zero.dtsi
- add required Motorcomm PHY DT property to enable clock
- fix regulator ranges: VDD_CPU and VDD_GPU were swapped
- add comment about broken SD card detect
- reorder PMIC properties to match recommended order

Andre Przywara (3):
arm64: dts: allwinner: h616: Split Orange Pi Zero 2 DT
dt-bindings: arm: sunxi: document Orange Pi Zero 3 board name
arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support

 .../devicetree/bindings/arm/sunxi.yaml        |   5 +
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun50i-h616-orangepi-zero.dtsi  | 134 ++++++++++++++++++
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 119 +---------------
 .../allwinner/sun50i-h618-orangepi-zero3.dts  |  94 ++++++++++++
 5 files changed, 235 insertions(+), 118 deletions(-)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts
Signature · 1 line
2.25.1
#1 lore raw

PATCH v2 1/3 arm64: dts: allwinner: h616: Split Orange Pi Zero 2 DT

The Orange Pi Zero 2 got a successor (Zero 3), which shares quite some DT nodes with the Zero 2, but comes with a different PMIC.

Move the common parts (except the PMIC) into a new shared file, and include that from the existing board .dts file.

No functional change, the generated DTB is the same, except for some phandle numbering differences.

---
 .../allwinner/sun50i-h616-orangepi-zero.dtsi  | 134 ++++++++++++++++++
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 119 +---------------
 2 files changed, 135 insertions(+), 118 deletions(-)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi
arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi new file +134 -0
new file mode 100644
index 0000000000000..8788c129b2887
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ *
+ * DT nodes common between Orange Pi Zero 2 and Orange Pi Zero 3.
+ * Excludes PMIC nodes and properties, since they are different between the two.
+ */
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		ethernet0 = &emac0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+			default-state = "on";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+		};
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the USB-C socket */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_vcc5v>;
+		enable-active-high;
+		gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+/* USB 2 & 3 are on headers only. */
+
+&emac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ext_rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	allwinner,rx-delay-ps = <3100>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&mdio0 {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&spi0  {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+&usbotg {
+	/*
+	 * PHY0 pins are connected to a USB-C socket, but a role switch
+	 * is not implemented: both CC pins are pulled to GND.
+	 * The VBUS pins power the device, so a fixed peripheral mode
+	 * is the best choice.
+	 * The board can be powered via GPIOs, in this case port0 *can*
+	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
+	 * then provided by the GPIOs. Any user of this setup would
+	 * need to adjust the DT accordingly: dr_mode set to "host",
+	 * enabling OHCI0 and EHCI0.
+	 */
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts +1 -118

140 lines not on this page · raw message

Signature · 1 line
2.25.1
maintainer Acked-by on v2 1/3
#2 lore raw

Re: [PATCH v2 1/3] arm64: dts: allwinner: h616: Split Orange Pi Zero 2 DT

Dne petek, 04. avgust 2023 ob 19:08:54 CEST je Andre Przywara napisal(a):

Quoted 10 lines

The Orange Pi Zero 2 got a successor (Zero 3), which shares quite some DT nodes with the Zero 2, but comes with a different PMIC.

Move the common parts (except the PMIC) into a new shared file, and include that from the existing board .dts file.

No functional change, the generated DTB is the same, except for some phandle numbering differences.

Best regards,
Jernej

Quoted 35 lines
---
 .../allwinner/sun50i-h616-orangepi-zero.dtsi  | 134 ++++++++++++++++++
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 119 +---------------
 2 files changed, 135 insertions(+), 118 deletions(-)
 create mode 100644

arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi

(quoted diff) +0 -0

b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi new file mode 100644
index 0000000000000..8788c129b2887

arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi new file +6 -0
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ *
+ * DT nodes common between Orange Pi Zero 2 and Orange Pi Zero 3.
+ * Excludes PMIC nodes and properties, since they are different between the

two. + */

arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi new file +14 -0
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		ethernet0 = &emac0;
+		serial0 = &uart0;
+	};
+
+	chosen {

arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi

Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi new file +10 -0
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 

*/

arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi

Quoted 7 lines
arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi new file +7 -0
+			default-state = "on";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 

*/

arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi

Quoted 5 lines
arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi new file +5 -0
+		};
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the USB-C socket 

*/

Quoted 117 lines
arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi new file +91 -0
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_vcc5v>;
+		enable-active-high;
+		gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+/* USB 2 & 3 are on headers only. */
+
+&emac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ext_rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	allwinner,rx-delay-ps = <3100>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&mdio0 {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&spi0  {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+&usbotg {
+	/*
+	 * PHY0 pins are connected to a USB-C socket, but a role switch
+	 * is not implemented: both CC pins are pulled to GND.
+	 * The VBUS pins power the device, so a fixed peripheral mode
+	 * is the best choice.
+	 * The board can be powered via GPIOs, in this case port0 *can*
+	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
+	 * then provided by the GPIOs. Any user of this setup would
+	 * need to adjust the DT accordingly: dr_mode set to "host",
+	 * enabling OHCI0 and EHCI0.
+	 */
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
(quoted diff) +0 -0

b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts index cb8600d0ea1ef..d6e732b12c52d 100644

arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts +1 -12
@@ -5,95 +5,19 @@
 
 /dts-v1/;
 
-#include "sun50i-h616.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/leds/common.h>
+#include "sun50i-h616-orangepi-zero.dtsi"
 
 / {
 	model = "OrangePi Zero2";
 	compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
-
-	aliases {
-		ethernet0 = &emac0;
-		serial0 = &uart0;
-	};
-
-	chosen {

arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts line 33

Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts +0 -10
-		stdout-path = "serial0:115200n8";
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led-0 {
-			function = LED_FUNCTION_POWER;
-			color = <LED_COLOR_ID_RED>;
-			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* 

PC12 */

arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts

Quoted 7 lines
arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts +0 -7
-			default-state = "on";
-		};
-
-		led-1 {
-			function = LED_FUNCTION_STATUS;
-			color = <LED_COLOR_ID_GREEN>;
-			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* 

PC13 */

arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts

Quoted 5 lines
arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts +0 -5
-		};
-	};
-
-	reg_vcc5v: vcc5v {
-		/* board wide 5V supply directly from the USB-C socket 

*/

Quoted 99 lines
arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts +0 -84
-		compatible = "regulator-fixed";
-		regulator-name = "vcc-5v";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-	};
-
-	reg_usb1_vbus: regulator-usb1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usb1-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&reg_vcc5v>;
-		enable-active-high;
-		gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
-	};
 };
 
-&ehci1 {
-	status = "okay";
-};
-
-/* USB 2 & 3 are on headers only. */
-
 &emac0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&ext_rgmii_pins>;
-	phy-mode = "rgmii";
-	phy-handle = <&ext_rgmii_phy>;
 	phy-supply = <&reg_dcdce>;
-	allwinner,rx-delay-ps = <3100>;
-	allwinner,tx-delay-ps = <700>;
-	status = "okay";
-};
-
-&mdio0 {
-	ext_rgmii_phy: ethernet-phy@1 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <1>;
-	};
 };
 
 &mmc0 {
 	vmmc-supply = <&reg_dcdce>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
-	bus-width = <4>;
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
 };
 
 &r_rsb {
@@ -211,44 +135,3 @@ &pio {
 	vcc-ph-supply = <&reg_aldo1>;
 	vcc-pi-supply = <&reg_aldo1>;
 };
-
-&spi0  {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
-
-	flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <40000000>;
-	};
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_ph_pins>;
-	status = "okay";
-};
-
-&usbotg {
-	/*
-	 * PHY0 pins are connected to a USB-C socket, but a role switch
-	 * is not implemented: both CC pins are pulled to GND.
-	 * The VBUS pins power the device, so a fixed peripheral mode
-	 * is the best choice.
-	 * The board can be powered via GPIOs, in this case port0 *can*
-	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
-	 * then provided by the GPIOs. Any user of this setup would
-	 * need to adjust the DT accordingly: dr_mode set to "host",
-	 * enabling OHCI0 and EHCI0.
-	 */
-	dr_mode = "peripheral";
-	status = "okay";
-};
-
-&usbphy {
-	usb1_vbus-supply = <&reg_usb1_vbus>;
-	status = "okay";
-};
#3 lore raw

PATCH v2 2/3 dt-bindings: arm: sunxi: document Orange Pi Zero 3 board name

In reply to Andre Przywara

The Orange Pi Zero 3 board is an updated version of the Zero 2 board. It uses a SoC called H618, which just seems to be an H616 with more L2 cache.

Add the board/SoC compatible string pair to the list of known boards.

---
 Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
 1 file changed, 5 insertions(+)
Documentation/devicetree/bindings/arm/sunxi.yaml +5 -0
index ee8fdd2da869a..58f322b9585f2 100644
@@ -997,4 +997,9 @@ properties:
           - const: xunlong,orangepi-zero2
           - const: allwinner,sun50i-h616
 
+      - description: Xunlong OrangePi Zero 3
+        items:
+          - const: xunlong,orangepi-zero3
+          - const: allwinner,sun50i-h618
+
 additionalProperties: true
Signature · 1 line
2.25.1
maintainer Acked-by on v2 2/3
#4 lore raw

Re: [PATCH v2 2/3] dt-bindings: arm: sunxi: document Orange Pi Zero 3 board name

Dne petek, 04. avgust 2023 ob 19:08:55 CEST je Andre Przywara napisal(a):

Quoted 8 lines

The Orange Pi Zero 3 board is an updated version of the Zero 2 board. It uses a SoC called H618, which just seems to be an H616 with more L2 cache.

Add the board/SoC compatible string pair to the list of known boards.

Best regards,
Jernej

Quoted 19 lines
---
 Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
 1 file changed, 5 insertions(+)
(quoted diff) +0 -0

b/Documentation/devicetree/bindings/arm/sunxi.yaml index ee8fdd2da869a..58f322b9585f2 100644

Documentation/devicetree/bindings/arm/sunxi.yaml +5 -0
@@ -997,4 +997,9 @@ properties:
           - const: xunlong,orangepi-zero2
           - const: allwinner,sun50i-h616
 
+      - description: Xunlong OrangePi Zero 3
+        items:
+          - const: xunlong,orangepi-zero3
+          - const: allwinner,sun50i-h618
+
 additionalProperties: true
#5 lore raw

PATCH v2 3/3 arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support

In reply to Andre Przywara

The OrangePi Zero 3 is a development board based on the Allwinner H618 SoC, which seems to be just an H616 with more L2 cache. The board itself is a slightly updated version of the Orange Pi Zero 2. It features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 1/1.5/2/4 GiB LPDDR4 DRAM SKUs (only up to 1GB on the Zero2)
- AXP313a PMIC (more capable AXP305 on the Zero2)
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 16MiB bootable SPI NOR flash (only 2MB on the Zero2)
- 1Gbps Ethernet port (via Motorcomm YT8531 PHY) (RTL8211 on the Zero2)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip

Add the devicetree file describing the currently supported features, namely LEDs, SD card, PMIC, SPI flash, USB. Ethernet seems unstable at the moment, though the basic functionality works.

---
 arch/arm64/boot/dts/allwinner/Makefile        |  1 +
 .../allwinner/sun50i-h618-orangepi-zero3.dts  | 94 +++++++++++++++++++
 2 files changed, 95 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts
arch/arm64/boot/dts/allwinner/Makefile +1 -0
index 6a96494a2e0a3..3b0ad54062381 100644
@@ -40,3 +40,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +94 -0

94 lines not on this page · raw message

Signature · 1 line
2.25.1
maintainer
#6 lore raw

Re: [PATCH v2 3/3] arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support

Dne petek, 04. avgust 2023 ob 19:08:56 CEST je Andre Przywara napisal(a):

Quoted 83 lines

The OrangePi Zero 3 is a development board based on the Allwinner H618 SoC, which seems to be just an H616 with more L2 cache. The board itself is a slightly updated version of the Orange Pi Zero 2. It features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 1/1.5/2/4 GiB LPDDR4 DRAM SKUs (only up to 1GB on the Zero2)
- AXP313a PMIC (more capable AXP305 on the Zero2)
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 16MiB bootable SPI NOR flash (only 2MB on the Zero2)
- 1Gbps Ethernet port (via Motorcomm YT8531 PHY) (RTL8211 on the Zero2)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip

Add the devicetree file describing the currently supported features, namely LEDs, SD card, PMIC, SPI flash, USB. Ethernet seems unstable at the moment, though the basic functionality works.

---
 arch/arm64/boot/dts/allwinner/Makefile        |  1 +
 .../allwinner/sun50i-h618-orangepi-zero3.dts  | 94 +++++++++++++++++++
 2 files changed, 95 insertions(+)
 create mode 100644

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

(quoted diff) +0 -0

b/arch/arm64/boot/dts/allwinner/Makefile index 6a96494a2e0a3..3b0ad54062381 100644

arch/arm64/boot/dts/allwinner/Makefile +1 -0
@@ -40,3 +40,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
(quoted diff) +0 -0

b/arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file mode 100644
index 0000000000000..96a6851728111

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +38 -0
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2023 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616-orangepi-zero.dtsi"
+
+/ {
+	model = "OrangePi Zero3";
+	compatible = "xunlong,orangepi-zero3", "allwinner,sun50i-h618";
+};
+
+&emac0 {
+	phy-supply = <&reg_dldo1>;
+};
+
+&ext_rgmii_phy {
+	motorcomm,clk-out-frequency-hz = <125000000>;
+};
+
+&mmc0 {
+	/*
+	 * The schematic shows the card detect pin wired up to PF6, via an
+	 * inverter, but it just doesn't work.
+	 */
+	broken-cd;
+	vmmc-supply = <&reg_dldo1>;
+};
+
+&r_i2c {
+	status = "okay";
+
+	axp313: pmic@36 {
+		compatible = "x-powers,axp313a";
+		reg = <0x36>;
+		#interrupt-cells = <1>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 48

Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +10 -0
+		interrupt-controller;
+		interrupt-parent = <&pio>;
+		interrupts = <2 9 IRQ_TYPE_LEVEL_LOW>;	/* PC9 */
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+
+		regulators {
+			/* Supplies VCC-PLL, so needs to be always 

on. */

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 3 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +3 -0
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = 

<1800000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 52

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt = 

<1800000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 4 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +4 -0
+				regulator-name = "vcc1v8";
+			};
+
+			/* Supplies VCC-IO, so needs to be always on. 

*/

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 3 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +3 -0
+			reg_dldo1: dldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = 

<3300000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 60

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt = 

<3300000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 6 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +6 -0
+				regulator-name = "vcc3v3";
+			};
+
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt = 

<810000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 67

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt = 

<990000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 69

Quoted 2 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +2 -0
+				regulator-name = "vdd-gpu-sys";
+			};

Is it safe to change sys voltage when system is running?

Best regards,
Jernej

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 4 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +4 -0
+
+			reg_dcdc2: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt = 

<810000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 74

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt = 

<1100000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 6 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +6 -0
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt = 

<1100000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 81

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt = 

<1100000>;

Quoted 13 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +13 -0
+				regulator-name = "vdd-dram";
+			};
+		};
+	};
+};
+
+&pio {
+	vcc-pc-supply = <&reg_dldo1>;
+	vcc-pf-supply = <&reg_dldo1>;
+	vcc-pg-supply = <&reg_aldo1>;
+	vcc-ph-supply = <&reg_dldo1>;
+	vcc-pi-supply = <&reg_dldo1>;
+};
#7 lore raw

Re: [PATCH v2 3/3] arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support

On Fri, 04 Aug 2023 21:05:36 +0200
Jernej Škrabec <[email protected]> wrote:

Hi Jernej,

Quoted 119 lines

Dne petek, 04. avgust 2023 ob 19:08:56 CEST je Andre Przywara napisal(a):

Quoted 83 lines

The OrangePi Zero 3 is a development board based on the Allwinner H618 SoC, which seems to be just an H616 with more L2 cache. The board itself is a slightly updated version of the Orange Pi Zero 2. It features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 1/1.5/2/4 GiB LPDDR4 DRAM SKUs (only up to 1GB on the Zero2)
- AXP313a PMIC (more capable AXP305 on the Zero2)
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 16MiB bootable SPI NOR flash (only 2MB on the Zero2)
- 1Gbps Ethernet port (via Motorcomm YT8531 PHY) (RTL8211 on the Zero2)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip

Add the devicetree file describing the currently supported features, namely LEDs, SD card, PMIC, SPI flash, USB. Ethernet seems unstable at the moment, though the basic functionality works.

---
 arch/arm64/boot/dts/allwinner/Makefile        |  1 +
 .../allwinner/sun50i-h618-orangepi-zero3.dts  | 94 +++++++++++++++++++
 2 files changed, 95 insertions(+)
 create mode 100644

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

(quoted diff) +0 -0

b/arch/arm64/boot/dts/allwinner/Makefile index 6a96494a2e0a3..3b0ad54062381 100644

arch/arm64/boot/dts/allwinner/Makefile +1 -0
@@ -40,3 +40,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb
(quoted diff) +0 -0

b/arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file mode 100644
index 0000000000000..96a6851728111

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +38 -0
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2023 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616-orangepi-zero.dtsi"
+
+/ {
+	model = "OrangePi Zero3";
+	compatible = "xunlong,orangepi-zero3", "allwinner,sun50i-h618";
+};
+
+&emac0 {
+	phy-supply = <&reg_dldo1>;
+};
+
+&ext_rgmii_phy {
+	motorcomm,clk-out-frequency-hz = <125000000>;
+};
+
+&mmc0 {
+	/*
+	 * The schematic shows the card detect pin wired up to PF6, via an
+	 * inverter, but it just doesn't work.
+	 */
+	broken-cd;
+	vmmc-supply = <&reg_dldo1>;
+};
+
+&r_i2c {
+	status = "okay";
+
+	axp313: pmic@36 {
+		compatible = "x-powers,axp313a";
+		reg = <0x36>;
+		#interrupt-cells = <1>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 48

Quoted 10 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +10 -0
+		interrupt-controller;
+		interrupt-parent = <&pio>;
+		interrupts = <2 9 IRQ_TYPE_LEVEL_LOW>;	/* PC9 */
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+
+		regulators {
+			/* Supplies VCC-PLL, so needs to be always   

on. */

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 3 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +3 -0
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt =   

<1800000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 52

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt =   

<1800000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 4 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +4 -0
+				regulator-name = "vcc1v8";
+			};
+
+			/* Supplies VCC-IO, so needs to be always on.   

*/

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 3 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +3 -0
+			reg_dldo1: dldo1 {
+				regulator-always-on;
+				regulator-min-microvolt =   

<3300000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 60

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt =   

<3300000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 6 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +6 -0
+				regulator-name = "vcc3v3";
+			};
+
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt =   

<810000>;

Quoted 6 lines

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 67

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt =   

<990000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 69

Quoted 2 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +2 -0
+				regulator-name = "vdd-gpu-sys";
+			};  

Is it safe to change sys voltage when system is running?

I don't know. All I know is that the H616 datasheet lists VDD_SYS as having the exact same range as VDD_GPU, and that is does not give a "typical" voltage value. As this DT stands at the moment, this doesn't really matter, since nothing will change DCDC1.

I see that the Orange Pi Zero 2 (with a "proper" PMIC) also ties SYS and GPU together, so it's not just because of the few rails of the AXP313.

I'd say we will figure that out once we start experimenting with GPU DVFS, but meanwhile nothing references DCDC1, so it will just stay put at the AXP313's 0.9V reset value.

Does that make sense?

Cheers,
Andre

Quoted 34 lines

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 4 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +4 -0
+
+			reg_dcdc2: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt =   

<810000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 74

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt =   

<1100000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 6 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +6 -0
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt =   

<1100000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 81

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt =   

<1100000>;

Quoted 13 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +13 -0
+				regulator-name = "vdd-dram";
+			};
+		};
+	};
+};
+
+&pio {
+	vcc-pc-supply = <&reg_dldo1>;
+	vcc-pf-supply = <&reg_dldo1>;
+	vcc-pg-supply = <&reg_aldo1>;
+	vcc-ph-supply = <&reg_dldo1>;
+	vcc-pi-supply = <&reg_dldo1>;
+};  
maintainer Reviewed-by
#8 lore raw

Re: [PATCH v2 3/3] arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support

Dne sobota, 05. avgust 2023 ob 00:58:27 CEST je Andre Przywara napisal(a):

Quoted 91 lines

On Fri, 04 Aug 2023 21:05:36 +0200
Jernej Škrabec <[email protected]> wrote:

Hi Jernej,

Quoted 86 lines

Dne petek, 04. avgust 2023 ob 19:08:56 CEST je Andre Przywara napisal(a):

Quoted 85 lines

The OrangePi Zero 3 is a development board based on the Allwinner H618 SoC,
which seems to be just an H616 with more L2 cache. The board itself is a slightly updated version of the Orange Pi Zero 2. It features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 1/1.5/2/4 GiB LPDDR4 DRAM SKUs (only up to 1GB on the Zero2)
- AXP313a PMIC (more capable AXP305 on the Zero2)
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 16MiB bootable SPI NOR flash (only 2MB on the Zero2)
- 1Gbps Ethernet port (via Motorcomm YT8531 PHY) (RTL8211 on the Zero2)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip

Add the devicetree file describing the currently supported features, namely LEDs, SD card, PMIC, SPI flash, USB. Ethernet seems unstable at the moment, though the basic functionality works.

---

 arch/arm64/boot/dts/allwinner/Makefile        |  1 +
 .../allwinner/sun50i-h618-orangepi-zero3.dts  | 94 +++++++++++++++++++
 2 files changed, 95 insertions(+)
 create mode 100644

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

(quoted diff) +0 -0

b/arch/arm64/boot/dts/allwinner/Makefile index
6a96494a2e0a3..3b0ad54062381
100644

arch/arm64/boot/dts/allwinner/Makefile +1 -0
@@ -40,3 +40,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
 
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
 
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h618-orangepi-zero3.dtb

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file mode 100644
index 0000000000000..96a6851728111

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +33 -0
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2023 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616-orangepi-zero.dtsi"
+
+/ {
+	model = "OrangePi Zero3";
+	compatible = "xunlong,orangepi-zero3", "allwinner,sun50i-h618";
+};
+
+&emac0 {
+	phy-supply = <&reg_dldo1>;
+};
+
+&ext_rgmii_phy {
+	motorcomm,clk-out-frequency-hz = <125000000>;
+};
+
+&mmc0 {
+	/*
+	 * The schematic shows the card detect pin wired up to PF6, via an
+	 * inverter, but it just doesn't work.
+	 */
+	broken-cd;
+	vmmc-supply = <&reg_dldo1>;
+};
+
+&r_i2c {
+	status = "okay";
Quoted 8 lines
Quoted 8 lines

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 8 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +8 -0
+
+	axp313: pmic@36 {
+		compatible = "x-powers,axp313a";
+		reg = <0x36>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		interrupt-parent = <&pio>;
+		interrupts = <2 9 IRQ_TYPE_LEVEL_LOW>;	/* PC9 

*/

Quoted 16 lines
Quoted 16 lines

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 7 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +7 -0
+
+		vin1-supply = <&reg_vcc5v>;
+		vin2-supply = <&reg_vcc5v>;
+		vin3-supply = <&reg_vcc5v>;
+
+		regulators {
+			/* Supplies VCC-PLL, so needs to be always

on. */

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 3 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +3 -0
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt =

<1800000>;

Quoted 8 lines
Quoted 8 lines

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 52

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt =

<1800000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 4 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +4 -0
+				regulator-name = "vcc1v8";
+			};
+
+			/* Supplies VCC-IO, so needs to be always 

on.

Quoted 36 lines
Quoted 22 lines

*/

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 3 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +3 -0
+			reg_dldo1: dldo1 {
+				regulator-always-on;
+				regulator-min-microvolt =

<3300000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 60

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt =

<3300000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 6 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +6 -0
+				regulator-name = "vcc3v3";
+			};
+
+			reg_dcdc1: dcdc1 {
+				regulator-always-on;
+				regulator-min-microvolt =

<810000>;

Quoted 8 lines

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 67

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt =

<990000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 69

Quoted 2 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +2 -0
+				regulator-name = "vdd-gpu-sys";
+			};

Is it safe to change sys voltage when system is running?

I don't know. All I know is that the H616 datasheet lists VDD_SYS as having the exact same range as VDD_GPU, and that is does not give a "typical" voltage value. As this DT stands at the moment, this doesn't really matter, since nothing will change DCDC1.

Quoted 8 lines

I see that the Orange Pi Zero 2 (with a "proper" PMIC) also ties SYS and GPU together, so it's not just because of the few rails of the AXP313.

I'd say we will figure that out once we start experimenting with GPU DVFS, but meanwhile nothing references DCDC1, so it will just stay put at the AXP313's 0.9V reset value.

Does that make sense?

Yeah, I'm fine with it.

Best regards,
Jernej

Quoted 41 lines

Cheers,
Andre

Quoted 37 lines

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 4 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +4 -0
+
+			reg_dcdc2: dcdc2 {
+				regulator-always-on;
+				regulator-min-microvolt =

<810000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 74

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt =

<1100000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts

Quoted 6 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +6 -0
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-always-on;
+				regulator-min-microvolt =

<1100000>;

arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts line 81

Quoted 1 line
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +1 -0
+				regulator-max-microvolt =

<1100000>;

Quoted 13 lines
arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts new file +13 -0
+				regulator-name = "vdd-dram";
+			};
+		};
+	};
+};
+
+&pio {
+	vcc-pc-supply = <&reg_dldo1>;
+	vcc-pf-supply = <&reg_dldo1>;
+	vcc-pg-supply = <&reg_aldo1>;
+	vcc-ph-supply = <&reg_dldo1>;
+	vcc-pi-supply = <&reg_dldo1>;
+};
maintainer Applied
#9 lore raw
In reply to Andre Przywara

Dne petek, 04. avgust 2023 ob 19:08:53 CEST je Andre Przywara napisal(a):

Quoted 13 lines

Hi,

quick update of the series, mostly cosmetic fixes, except for the regulator range. For a changelog, see below.

==================
Orange Pi recently released the Orange Pi Zero 3 board, which is some updated version of their former Zero 2 development board. Some component changes (Motorcomm PHY instead of Realtek, different PMIC), some board layout changes, and it ships with up to 4GB of DRAM now. The SoC is now labelled H618 instead of H616, which apparently is the same, just with more L2 cache.

Quoted 8 lines

Split the existing OPi Zero2 DT, to allow sharing most DT nodes, then add the binding documentation and DT for the new board.

Linux v6.5-rc boots out of the box (the PMIC driver just made it in), and most things work: UART, PSCI, GPIO, SPI flash, SD card, USB. Ethernet is somewhat working: I get an IP address via DHCP, and can for instance start SSH, but it hangs at some point. I suspect some PHY setup problem, though others have it working. Help or advice welcome.

Applied, thanks!

Best regards,
Jernej

Quoted 25 lines

Cheers,
Andre

Changelog v1 .. v2:
- rename common .dtsi file to sun50i-h616-orangepi-zero.dtsi
- add required Motorcomm PHY DT property to enable clock
- fix regulator ranges: VDD_CPU and VDD_GPU were swapped
- add comment about broken SD card detect
- reorder PMIC properties to match recommended order

Andre Przywara (3):
arm64: dts: allwinner: h616: Split Orange Pi Zero 2 DT
dt-bindings: arm: sunxi: document Orange Pi Zero 3 board name
arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support

 .../devicetree/bindings/arm/sunxi.yaml        |   5 +
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun50i-h616-orangepi-zero.dtsi  | 134 ++++++++++++++++++
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 119 +---------------
 .../allwinner/sun50i-h618-orangepi-zero3.dts  |  94 ++++++++++++
 5 files changed, 235 insertions(+), 118 deletions(-)
 create mode 100644

arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero.dtsi create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h618-orangepi-zero3.dts