Skip to contentSkip to conversation

arm64: ti: k3-am62: Add display support

PATCH Superseded Aradhya Bhatia 2 participants 10 messages Aug 7, 2023 – Aug 8, 2023

Subsystems (2)

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v4 cover arm64: ti: k3-am62: Add display support

Hi all,

The patch series adds DT nodes for Display SubSystem (DSS) and other peripherals required to enable the HDMI audio and video on the AM625 SK, AM62-LP SK, as well as the AM625 based Beagle-Play platforms. An HDMI monitor can be connected to the boards for the audio/video outputs.

The series adding the compatible and basic driver support[0] is in the drm-misc-next and linux-next queues and is expected to be in the mainline by v6.6-rc1. Patch 5/6 also requires Nishanth Menon's patch[1] that introduces debounce select mux macros. This patch too is not in v6.5-rc1 but has been picked up in ti-next[2] and hence, is present in linux-next.

Patches 4 and 5 have been picked up from TI's vendor tree[3] based off linux-kernel v6.1.

Regards
Aradhya

Change Log:
V3 -> V4:
- Added "Fixes" tag for patch 1/6.
- Rebased to linux-next.
- Enabled display at board level and disabled at SoC level.
- Dropped OLDI pinmux configuration as OLDI output comes directly from the SoC and muxing is not required.
- Squashed DSS pinmux patches into their platform specific HDMI support patches, because it did not make sense to have only one set of pinmux config separated in a patch.

V2 -> V3:
- Updated the compatible from "ti,am65x-dss" to "ti,am625-dss".
- Peripheral nodes like HDMI TX, HDMI connector are now added to k3-am62x-sk-common.dtsi instead of k3-am625-sk.dts, in order to support AM62-LP SK-EVM as well.
- Dropped the HDMI master clock node as it is not connected on the EVM, and should not have been added in the first place.
- Re-worded and Re-ordered commits.
- Dropped Rahul Ravikumar's R-bs because of the changes.
- Added AM625 based Beagle-Play for HDMI support.
- Added HDMI audio support as well.

V1 -> V2:
- Removed repetitive data in dss_ports

V3: https://lore.kernel.org/all/[email protected]/
V2: https://lore.kernel.org/all/[email protected]/
V1: https://lore.kernel.org/all/[email protected]/

[0]: https://lore.kernel.org/all/[email protected]/
[1]: https://lore.kernel.org/all/[email protected]/
[2]: https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git/commit/?id=0bec3d7ecc7493b0e530f6f34539841ef6779006
[3]: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/log/?h=ti-linux-6.1.y-cicd

Aradhya Bhatia (4):
arm64: dts: ti: k3-am62x-sk-common: Update main-i2c1 frequency
arm64: dts: ti: k3-am62-main: Add node for DSS
arm64: dts: ti: k3-am62x-sk-common: Add HDMI support
arm64: defconfig: Enable ITE_IT66121 HDMI transmitter

Jai Luthra (1):
arm64: dts: ti: am62x-sk: Add overlay for HDMI audio

Nishanth Menon (1):
arm64: dts: ti: k3-am625-beagleplay: Add HDMI support

 arch/arm64/boot/dts/ti/Makefile               |   3 +
 arch/arm64/boot/dts/ti/k3-am62-main.dtsi      |  25 +++
 .../arm64/boot/dts/ti/k3-am625-beagleplay.dts | 158 ++++++++++++++++++
 .../arm64/boot/dts/ti/k3-am62x-sk-common.dtsi |  95 ++++++++++-
 .../boot/dts/ti/k3-am62x-sk-hdmi-audio.dtso   |  40 +++++
 arch/arm64/configs/defconfig                  |   1 +
 6 files changed, 321 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am62x-sk-hdmi-audio.dtso

base-commit: f7dc24b3413851109c4047b22997bd0d95ed52a2

Signature · 1 line
2.40.1
#1 lore raw

PATCH v4 1/6 arm64: dts: ti: k3-am62x-sk-common: Update main-i2c1 frequency

The Display Data Channel (DDC) transactions between an HDMI transmitter (SIL9022A in this case) and an HDMI monitor, occur at a maximum of 100KHz. That's the maximum supported frequency within DDC standards.

While the SIL9022A can transact with the core at 400KHz, it needs to drop the frequency to 100KHz when communicating with the monitor, otherwise, the i2c controller times out and shows warning like this.

[  985.773431] omap_i2c 20010000.i2c: controller timed out

That feature, however, has not been enabled in the SIL9022 driver.

Since, dropping the frequency doesn't affect any other devices on the bus, drop the main-i2c1 frequency from 400KHz to 100KHz.

Fixes a841581451af ("arm64: dts: ti: Refractor AM625 SK dts")
---
 arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi +1 -1
index 34c8ffc553ec..540ed8a0d7fb 100644
@@ -300,7 +300,7 @@ &main_i2c1 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c1_pins_default>;
-	clock-frequency = <400000>;
+	clock-frequency = <100000>;
 
 	tlv320aic3106: audio-codec@1b {
 		#sound-dai-cells = <0>;
Signature · 1 line
2.40.1
#2 lore raw

PATCH v4 2/6 arm64: dts: ti: k3-am62-main: Add node for DSS

In reply to Aradhya Bhatia

Add Display SubSystem (DSS) DT node for the AM625 SoC.

The DSS supports one each of video pipeline (vid) and video-lite pipeline (vidl1). It outputs OLDI signals on one video port (VP1) and DPI signals on another (VP2). The video ports are connected to the pipelines via 2 identical overlay managers (ovr1 and ovr2).

---
 arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 25 ++++++++++++++++++++++++
 1 file changed, 25 insertions(+)
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +25 -0
index ef90b2bc81eb..6cdca8df1091 100644
@@ -717,6 +717,31 @@ cpts@3d000 {
 		};
 	};
 
+	dss: dss@30200000 {
+		compatible = "ti,am625-dss";
+		reg = <0x00 0x30200000 0x00 0x1000>, /* common */
+		      <0x00 0x30202000 0x00 0x1000>, /* vidl1 */
+		      <0x00 0x30206000 0x00 0x1000>, /* vid */
+		      <0x00 0x30207000 0x00 0x1000>, /* ovr1 */
+		      <0x00 0x30208000 0x00 0x1000>, /* ovr2 */
+		      <0x00 0x3020a000 0x00 0x1000>, /* vp1: Used for OLDI */
+		      <0x00 0x3020b000 0x00 0x1000>; /* vp2: Used as DPI Out */
+		reg-names = "common", "vidl1", "vid",
+			"ovr1", "ovr2", "vp1", "vp2";
+		power-domains = <&k3_pds 186 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 186 6>,
+			 <&k3_clks 186 0>,
+			 <&k3_clks 186 2>;
+		clock-names = "fck", "vp1", "vp2";
+		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		dss_ports: ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
 	hwspinlock: spinlock@2a000000 {
 		compatible = "ti,am64-hwspinlock";
 		reg = <0x00 0x2a000000 0x00 0x1000>;
Signature · 1 line
2.40.1
#3 lore raw

Re: [PATCH v4 2/6] arm64: dts: ti: k3-am62-main: Add node for DSS

Hello Aradhya,

Quoted 21 lines · Aradhya Bhatia

Add Display SubSystem (DSS) DT node for the AM625 SoC.

The DSS supports one each of video pipeline (vid) and video-lite pipeline (vidl1). It outputs OLDI signals on one video port (VP1) and DPI signals on another (VP2). The video ports are connected to the pipelines via 2 identical overlay managers (ovr1 and ovr2).

---
  arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 25 ++++++++++++++++++++++++
  1 file changed, 25 insertions(+)
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +1 -0
index ef90b2bc81eb..6cdca8df1091 100644
@@ -717,6 +717,31 @@ cpts@3d000 {
  		};
  	};
 
+	dss: dss@30200000 {

arch/arm64/boot/dts/ti/k3-am62-main.dtsi cpts@3d000 { · line 730

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +10 -0
+		compatible = "ti,am625-dss";
+		reg = <0x00 0x30200000 0x00 0x1000>, /* common */
+		      <0x00 0x30202000 0x00 0x1000>, /* vidl1 */
+		      <0x00 0x30206000 0x00 0x1000>, /* vid */
+		      <0x00 0x30207000 0x00 0x1000>, /* ovr1 */
+		      <0x00 0x30208000 0x00 0x1000>, /* ovr2 */
+		      <0x00 0x3020a000 0x00 0x1000>, /* vp1: Used for OLDI */
+		      <0x00 0x3020b000 0x00 0x1000>; /* vp2: Used as DPI Out */
+		reg-names = "common", "vidl1", "vid",
+			"ovr1", "ovr2", "vp1", "vp2";

Indentation is off here.

Quoted 7 lines
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +7 -0
+		power-domains = <&k3_pds 186 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 186 6>,
+			 <&k3_clks 186 0>,
+			 <&k3_clks 186 2>;
+		clock-names = "fck", "vp1", "vp2";
+		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";

arch/arm64/boot/dts/ti/k3-am62-main.dtsi cpts@3d000 { · line 747

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +7 -0
+
+		dss_ports: ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
  	hwspinlock: spinlock@2a000000 {
  		compatible = "ti,am64-hwspinlock";
  		reg = <0x00 0x2a000000 0x00 0x1000>;

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#4 lore raw

PATCH v4 3/6 arm64: dts: ti: k3-am62x-sk-common: Add HDMI support

In reply to Aradhya Bhatia

The DSS outputs DPI signals via its second video port (VP2). The DPI output from DSS is 24 bits (RGB888) and is forwarded to an HDMI transmitter (SIL9022) on the board.

Add pinmux info for DSS DPI output.

Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector on the AM625 SK and AM62-LP SK platforms.

Additionally, connect the output of DSS (VP2) with input of the HDMI TX, and the output of HDMI TX to the input of the HDMI connector.

---
 .../arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 93 +++++++++++++++++++
 1 file changed, 93 insertions(+)
arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi +93 -0
index 540ed8a0d7fb..edbe5295373b 100644
@@ -114,6 +114,17 @@ sound_master: simple-audio-card,codec {
 			clocks = <&tlv320_mclk>;
 		};
 	};
+
+	hdmi0: connector-hdmi {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "a";
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&sii9022_out>;
+			};
+		};
+	};
 };
 
 &main_pmx0 {
@@ -226,6 +237,39 @@ AM62X_IOPAD(0x08c, PIN_OUTPUT, 2) /* (L25/J17) GPMC0_WEN.MCASP1_AXR0 */
 			AM62X_IOPAD(0x084, PIN_INPUT, 2) /* (L23/K20) GPMC0_ADVN_ALE.MCASP1_AXR2 */
 		>;
 	};
+
+	main_dss0_pins_default: main-dss0-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0100, PIN_OUTPUT, 0) /* (AC25) VOUT0_VSYNC */
+			AM62X_IOPAD(0x00f8, PIN_OUTPUT, 0) /* (AB24) VOUT0_HSYNC */
+			AM62X_IOPAD(0x0104, PIN_OUTPUT, 0) /* (AC24) VOUT0_PCLK */
+			AM62X_IOPAD(0x00fc, PIN_OUTPUT, 0) /* (Y20) VOUT0_DE */
+			AM62X_IOPAD(0x00b8, PIN_OUTPUT, 0) /* (U22) VOUT0_DATA0 */
+			AM62X_IOPAD(0x00bc, PIN_OUTPUT, 0) /* (V24) VOUT0_DATA1 */
+			AM62X_IOPAD(0x00c0, PIN_OUTPUT, 0) /* (W25) VOUT0_DATA2 */
+			AM62X_IOPAD(0x00c4, PIN_OUTPUT, 0) /* (W24) VOUT0_DATA3 */
+			AM62X_IOPAD(0x00c8, PIN_OUTPUT, 0) /* (Y25) VOUT0_DATA4 */
+			AM62X_IOPAD(0x00cc, PIN_OUTPUT, 0) /* (Y24) VOUT0_DATA5 */
+			AM62X_IOPAD(0x00d0, PIN_OUTPUT, 0) /* (Y23) VOUT0_DATA6 */
+			AM62X_IOPAD(0x00d4, PIN_OUTPUT, 0) /* (AA25) VOUT0_DATA7 */
+			AM62X_IOPAD(0x00d8, PIN_OUTPUT, 0) /* (V21) VOUT0_DATA8 */
+			AM62X_IOPAD(0x00dc, PIN_OUTPUT, 0) /* (W21) VOUT0_DATA9 */
+			AM62X_IOPAD(0x00e0, PIN_OUTPUT, 0) /* (V20) VOUT0_DATA10 */
+			AM62X_IOPAD(0x00e4, PIN_OUTPUT, 0) /* (AA23) VOUT0_DATA11 */
+			AM62X_IOPAD(0x00e8, PIN_OUTPUT, 0) /* (AB25) VOUT0_DATA12 */
+			AM62X_IOPAD(0x00ec, PIN_OUTPUT, 0) /* (AA24) VOUT0_DATA13 */
+			AM62X_IOPAD(0x00f0, PIN_OUTPUT, 0) /* (Y22) VOUT0_DATA14 */
+			AM62X_IOPAD(0x00f4, PIN_OUTPUT, 0) /* (AA21) VOUT0_DATA15 */
+			AM62X_IOPAD(0x005c, PIN_OUTPUT, 1) /* (R24) GPMC0_AD8.VOUT0_DATA16 */
+			AM62X_IOPAD(0x0060, PIN_OUTPUT, 1) /* (R25) GPMC0_AD9.VOUT0_DATA17 */
+			AM62X_IOPAD(0x0064, PIN_OUTPUT, 1) /* (T25) GPMC0_AD10.VOUT0_DATA18 */
+			AM62X_IOPAD(0x0068, PIN_OUTPUT, 1) /* (R21) GPMC0_AD11.VOUT0_DATA19 */
+			AM62X_IOPAD(0x006c, PIN_OUTPUT, 1) /* (T22) GPMC0_AD12.VOUT0_DATA20 */
+			AM62X_IOPAD(0x0070, PIN_OUTPUT, 1) /* (T24) GPMC0_AD13.VOUT0_DATA21 */
+			AM62X_IOPAD(0x0074, PIN_OUTPUT, 1) /* (U25) GPMC0_AD14.VOUT0_DATA22 */
+			AM62X_IOPAD(0x0078, PIN_OUTPUT, 1) /* (U24) GPMC0_AD15.VOUT0_DATA23 */
+		>;
+	};
 };
 
 &mcu_pmx0 {
@@ -313,6 +357,38 @@ tlv320aic3106: audio-codec@1b {
 		IOVDD-supply = <&vcc_3v3_sys>;
 		DRVDD-supply = <&vcc_3v3_sys>;
 	};
+
+	sii9022: bridge-hdmi@3b {
+		compatible = "sil,sii9022";
+		reg = <0x3b>;
+
+		interrupt-parent = <&exp1>;
+		interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+
+		#sound-dai-cells = <0>;
+		sil,i2s-data-lanes = < 0 >;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sii9022_in: endpoint {
+					remote-endpoint = <&dpi1_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				sii9022_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
 };
 
 &sdhci0 {
@@ -410,3 +486,20 @@ &mcasp1 {
 	tx-num-evt = <32>;
 	rx-num-evt = <32>;
 };
+
+&dss {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_dss0_pins_default>;
+};
+
+&dss_ports {
+	/* VP2: DPI Output */
+	port@1 {
+		reg = <1>;
+
+		dpi1_out: endpoint {
+			remote-endpoint = <&sii9022_in>;
+		};
+	};
+};
Signature · 1 line
2.40.1
#5 lore raw

Re: [PATCH v4 3/6] arm64: dts: ti: k3-am62x-sk-common: Add HDMI support

Quoted 64 lines · Aradhya Bhatia

The DSS outputs DPI signals via its second video port (VP2). The DPI output from DSS is 24 bits (RGB888) and is forwarded to an HDMI transmitter (SIL9022) on the board.

Add pinmux info for DSS DPI output.

Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector on the AM625 SK and AM62-LP SK platforms.

Additionally, connect the output of DSS (VP2) with input of the HDMI TX, and the output of HDMI TX to the input of the HDMI connector.

---
  .../arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 93 +++++++++++++++++++
  1 file changed, 93 insertions(+)
arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi +32 -0
index 540ed8a0d7fb..edbe5295373b 100644
@@ -114,6 +114,17 @@ sound_master: simple-audio-card,codec {
  			clocks = <&tlv320_mclk>;
  		};
  	};
+
+	hdmi0: connector-hdmi {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "a";
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&sii9022_out>;
+			};
+		};
+	};
  };
 
  &main_pmx0 {
@@ -226,6 +237,39 @@ AM62X_IOPAD(0x08c, PIN_OUTPUT, 2) /* (L25/J17) GPMC0_WEN.MCASP1_AXR0 */
  			AM62X_IOPAD(0x084, PIN_INPUT, 2) /* (L23/K20) GPMC0_ADVN_ALE.MCASP1_AXR2 */
  		>;
  	};
+
+	main_dss0_pins_default: main-dss0-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0100, PIN_OUTPUT, 0) /* (AC25) VOUT0_VSYNC */
+			AM62X_IOPAD(0x00f8, PIN_OUTPUT, 0) /* (AB24) VOUT0_HSYNC */
+			AM62X_IOPAD(0x0104, PIN_OUTPUT, 0) /* (AC24) VOUT0_PCLK */
+			AM62X_IOPAD(0x00fc, PIN_OUTPUT, 0) /* (Y20) VOUT0_DE */
+			AM62X_IOPAD(0x00b8, PIN_OUTPUT, 0) /* (U22) VOUT0_DATA0 */
+			AM62X_IOPAD(0x00bc, PIN_OUTPUT, 0) /* (V24) VOUT0_DATA1 */
+			AM62X_IOPAD(0x00c0, PIN_OUTPUT, 0) /* (W25) VOUT0_DATA2 */
+			AM62X_IOPAD(0x00c4, PIN_OUTPUT, 0) /* (W24) VOUT0_DATA3 */
+			AM62X_IOPAD(0x00c8, PIN_OUTPUT, 0) /* (Y25) VOUT0_DATA4 */
+			AM62X_IOPAD(0x00cc, PIN_OUTPUT, 0) /* (Y24) VOUT0_DATA5 */
+			AM62X_IOPAD(0x00d0, PIN_OUTPUT, 0) /* (Y23) VOUT0_DATA6 */
+			AM62X_IOPAD(0x00d4, PIN_OUTPUT, 0) /* (AA25) VOUT0_DATA7 */
+			AM62X_IOPAD(0x00d8, PIN_OUTPUT, 0) /* (V21) VOUT0_DATA8 */
+			AM62X_IOPAD(0x00dc, PIN_OUTPUT, 0) /* (W21) VOUT0_DATA9 */
+			AM62X_IOPAD(0x00e0, PIN_OUTPUT, 0) /* (V20) VOUT0_DATA10 */
+			AM62X_IOPAD(0x00e4, PIN_OUTPUT, 0) /* (AA23) VOUT0_DATA11 */
+			AM62X_IOPAD(0x00e8, PIN_OUTPUT, 0) /* (AB25) VOUT0_DATA12 */
+			AM62X_IOPAD(0x00ec, PIN_OUTPUT, 0) /* (AA24) VOUT0_DATA13 */

arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi AM62X_IOPAD(0x08c, PIN_OUTPUT, 2) /* (L25/J17) GPMC0_WEN.MCASP1_AXR0 */ · line 270

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi +10 -0
+			AM62X_IOPAD(0x00f0, PIN_OUTPUT, 0) /* (Y22) VOUT0_DATA14 */
+			AM62X_IOPAD(0x00f4, PIN_OUTPUT, 0) /* (AA21) VOUT0_DATA15 */
+			AM62X_IOPAD(0x005c, PIN_OUTPUT, 1) /* (R24) GPMC0_AD8.VOUT0_DATA16 */
+			AM62X_IOPAD(0x0060, PIN_OUTPUT, 1) /* (R25) GPMC0_AD9.VOUT0_DATA17 */
+			AM62X_IOPAD(0x0064, PIN_OUTPUT, 1) /* (T25) GPMC0_AD10.VOUT0_DATA18 */
+			AM62X_IOPAD(0x0068, PIN_OUTPUT, 1) /* (R21) GPMC0_AD11.VOUT0_DATA19 */
+			AM62X_IOPAD(0x006c, PIN_OUTPUT, 1) /* (T22) GPMC0_AD12.VOUT0_DATA20 */
+			AM62X_IOPAD(0x0070, PIN_OUTPUT, 1) /* (T24) GPMC0_AD13.VOUT0_DATA21 */
+			AM62X_IOPAD(0x0074, PIN_OUTPUT, 1) /* (U25) GPMC0_AD14.VOUT0_DATA22 */
+			AM62X_IOPAD(0x0078, PIN_OUTPUT, 1) /* (U24) GPMC0_AD15.VOUT0_DATA23 */

Rest of the pinmux in the file uses padding of 3. Here you are using padding of 4. Consistency would be good.

Quoted 6 lines
arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi +2 -0
+		>;
+	};
  };
 
  &mcu_pmx0 {

arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi tlv320aic3106: audio-codec@1b { · line 364

Quoted 8 lines
arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi +5 -0
@@ -313,6 +357,38 @@ tlv320aic3106: audio-codec@1b {
  		IOVDD-supply = <&vcc_3v3_sys>;
  		DRVDD-supply = <&vcc_3v3_sys>;
  	};
+
+	sii9022: bridge-hdmi@3b {
+		compatible = "sil,sii9022";
+		reg = <0x3b>;
+

Line break not needed.

arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi tlv320aic3106: audio-codec@1b { · line 367

Quoted 3 lines
arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi +3 -0
+		interrupt-parent = <&exp1>;
+		interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+

Same.

Quoted 38 lines
arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi +31 -0
+		#sound-dai-cells = <0>;
+		sil,i2s-data-lanes = < 0 >;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sii9022_in: endpoint {
+					remote-endpoint = <&dpi1_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				sii9022_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
  };
 
  &sdhci0 {
@@ -410,3 +486,20 @@ &mcasp1 {
  	tx-num-evt = <32>;
  	rx-num-evt = <32>;
  };
+
+&dss {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_dss0_pins_default>;
+};
+

arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi &mcasp1 { · line 505

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi +10 -0
+&dss_ports {
+	/* VP2: DPI Output */
+	port@1 {
+		reg = <1>;
+
+		dpi1_out: endpoint {
+			remote-endpoint = <&sii9022_in>;
+		};
+	};
+};

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#6 lore raw

PATCH v4 4/6 arm64: dts: ti: am62x-sk: Add overlay for HDMI audio

In reply to Aradhya Bhatia

From: Jai Luthra <[email protected]>

Enable audio output over HDMI instead of the 3.5mm jack.

A FET switch (U65) on the EVM muxes serial audio lines coming from McASP between the codec (tlv320aic3106) and the HDMI bridge (sii9022).

By default it uses the codec, but it can be toggled to use the HDMI bridge by shorting a (J24) header on the board.

[a-bhatia1: Cosmetic changes]
---
 arch/arm64/boot/dts/ti/Makefile               |  3 ++
 .../boot/dts/ti/k3-am62x-sk-hdmi-audio.dtso   | 40 +++++++++++++++++++
 2 files changed, 43 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am62x-sk-hdmi-audio.dtso
arch/arm64/boot/dts/ti/Makefile +3 -0
index 437a3d7e8e3a..e3eadf69d43b 100644
@@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-dahlia.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-dev.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-wifi-yavia.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am62-lp-sk.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am62x-sk-hdmi-audio.dtbo
 
 # Boards with AM62Ax SoC
 dtb-$(CONFIG_ARCH_K3) += k3-am62a7-sk.dtb
@@ -68,6 +69,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
 
 # Enable support for device-tree overlays
+DTC_FLAGS_k3-am625-sk += -@
+DTC_FLAGS_k3-am62-lp-sk += -@
 DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
 DTC_FLAGS_k3-j721e-common-proc-board += -@
 DTC_FLAGS_k3-j721s2-common-proc-board += -@
arch/arm64/boot/dts/ti/k3-am62x-sk-hdmi-audio.dtso new file +40 -0
new file mode 100644
index 000000000000..43a0ddc123e5
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * Audio playback via HDMI for AM625-SK and AM62-LP SK.
+ *
+ * Links:
+ * AM625 SK: https://www.ti.com/tool/SK-AM62
+ * AM62-LP SK: https://www.ti.com/tool/SK-AM62-LP
+ *
+ * Copyright (C) 2023 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	hdmi_audio: sound-sii9022 {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "AM62x-Sil9022-HDMI";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&hdmi_dailink_master>;
+		simple-audio-card,frame-master = <&hdmi_dailink_master>;
+
+		hdmi_dailink_master: simple-audio-card,cpu {
+			sound-dai = <&mcasp1>;
+			system-clock-direction-out;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&sii9022>;
+		};
+	};
+};
+
+&mcasp1 {
+	auxclk-fs-ratio = <2177>;
+};
+
+&codec_audio {
+	status = "disabled";
+};
Signature · 1 line
2.40.1
#7 lore raw

PATCH v4 5/6 arm64: dts: ti: k3-am625-beagleplay: Add HDMI support

In reply to Aradhya Bhatia

From: Nishanth Menon <[email protected]>

The DSS outputs DPI signals via its second video port (VP2). The DPI output from DSS is 24 bits (RGB888) and is forwarded to an HDMI transmitter (ITE-IT66121) on the BeaglePlay platform. For audio output, BeaglePlay uses mcasp1.

Add pinmux info for DSS DPI signals.

Further, add support for HDMI audio and video output.

[a-bhatia1: Edit sound node properties and HDMI node and label names]
---
 .../arm64/boot/dts/ti/k3-am625-beagleplay.dts | 158 ++++++++++++++++++
 1 file changed, 158 insertions(+)
arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts +158 -0
index e07ddff22e07..582410be9570 100644
@@ -192,6 +192,34 @@ usr: button-usr {
 
 	};
 
+	hdmi0: connector-hdmi {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "a";
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&it66121_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "it66121 HDMI";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&hdmi_dailink_master>;
+		simple-audio-card,frame-master = <&hdmi_dailink_master>;
+
+		hdmi_dailink_master: simple-audio-card,cpu {
+			sound-dai = <&mcasp1>;
+			system-clock-direction-out;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&it66121>;
+		};
+	};
+
 	/* Workaround for errata i2329 - just use mdio bitbang */
 	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
@@ -422,6 +450,57 @@ pmic_irq_pins_default: pmic-irq-default-pins {
 			AM62X_IOPAD(0x01f4, PIN_INPUT_PULLUP, 0) /* (D16) EXTINTn */
 		>;
 	};
+
+	hdmi_gpio_pins_default: hdmi-gpio-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0094, PIN_INPUT_PULLUP | PIN_DEBOUNCE_CONF6, 7) /* (N20) GPMC0_BE1n.GPIO0_36 */
+			AM62X_IOPAD(0x0054, PIN_OUTPUT_PULLUP, 7) /* (P21) GPMC0_AD6.GPIO0_21 */
+		>;
+	};
+
+	mcasp_hdmi_pins_default: mcasp-hdmi-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0090, PIN_INPUT, 2) /* (M24) GPMC0_BE0n_CLE.MCASP1_ACLKX */
+			AM62X_IOPAD(0x0098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
+			AM62X_IOPAD(0x008c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEn.MCASP1_AXR0 */
+			AM62X_IOPAD(0x0088, PIN_INPUT, 2) /* (L24) GPMC0_OEn_REn.MCASP1_AXR1 */
+			AM62X_IOPAD(0x0084, PIN_INPUT, 2) /* (L23) GPMC0_ADVn_ALE.MCASP1_AXR2 */
+			AM62X_IOPAD(0x007c, PIN_INPUT, 2) /* (P25) GPMC0_CLK.MCASP1_AXR3 */
+		>;
+	};
+
+	dss0_pins_default: dss0-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0100, PIN_OUTPUT, 0) /* (AC25) VOUT0_VSYNC */
+			AM62X_IOPAD(0x00f8, PIN_OUTPUT, 0) /* (AB24) VOUT0_HSYNC */
+			AM62X_IOPAD(0x0104, PIN_OUTPUT, 0) /* (AC24) VOUT0_PCLK */
+			AM62X_IOPAD(0x00fc, PIN_OUTPUT, 0) /* (Y20) VOUT0_DE */
+			AM62X_IOPAD(0x00b8, PIN_OUTPUT, 0) /* (U22) VOUT0_DATA0 */
+			AM62X_IOPAD(0x00bc, PIN_OUTPUT, 0) /* (V24) VOUT0_DATA1 */
+			AM62X_IOPAD(0x00c0, PIN_OUTPUT, 0) /* (W25) VOUT0_DATA2 */
+			AM62X_IOPAD(0x00c4, PIN_OUTPUT, 0) /* (W24) VOUT0_DATA3 */
+			AM62X_IOPAD(0x00c8, PIN_OUTPUT, 0) /* (Y25) VOUT0_DATA4 */
+			AM62X_IOPAD(0x00cc, PIN_OUTPUT, 0) /* (Y24) VOUT0_DATA5 */
+			AM62X_IOPAD(0x00d0, PIN_OUTPUT, 0) /* (Y23) VOUT0_DATA6 */
+			AM62X_IOPAD(0x00d4, PIN_OUTPUT, 0) /* (AA25) VOUT0_DATA7 */
+			AM62X_IOPAD(0x00d8, PIN_OUTPUT, 0) /* (V21) VOUT0_DATA8 */
+			AM62X_IOPAD(0x00dc, PIN_OUTPUT, 0) /* (W21) VOUT0_DATA9 */
+			AM62X_IOPAD(0x00e0, PIN_OUTPUT, 0) /* (V20) VOUT0_DATA10 */
+			AM62X_IOPAD(0x00e4, PIN_OUTPUT, 0) /* (AA23) VOUT0_DATA11 */
+			AM62X_IOPAD(0x00e8, PIN_OUTPUT, 0) /* (AB25) VOUT0_DATA12 */
+			AM62X_IOPAD(0x00ec, PIN_OUTPUT, 0) /* (AA24) VOUT0_DATA13 */
+			AM62X_IOPAD(0x00f0, PIN_OUTPUT, 0) /* (Y22) VOUT0_DATA14 */
+			AM62X_IOPAD(0x00f4, PIN_OUTPUT, 0) /* (AA21) VOUT0_DATA15 */
+			AM62X_IOPAD(0x005c, PIN_OUTPUT, 1) /* (R24) GPMC0_AD8.VOUT0_DATA16 */
+			AM62X_IOPAD(0x0060, PIN_OUTPUT, 1) /* (R25) GPMC0_AD9.VOUT0_DATA17 */
+			AM62X_IOPAD(0x0064, PIN_OUTPUT, 1) /* (T25) GPMC0_AD10.VOUT0_DATA18 */
+			AM62X_IOPAD(0x0068, PIN_OUTPUT, 1) /* (R21) GPMC0_AD11.VOUT0_DATA19 */
+			AM62X_IOPAD(0x006c, PIN_OUTPUT, 1) /* (T22) GPMC0_AD12.VOUT0_DATA20 */
+			AM62X_IOPAD(0x0070, PIN_OUTPUT, 1) /* (T24) GPMC0_AD13.VOUT0_DATA21 */
+			AM62X_IOPAD(0x0074, PIN_OUTPUT, 1) /* (U25) GPMC0_AD14.VOUT0_DATA22 */
+			AM62X_IOPAD(0x0078, PIN_OUTPUT, 1) /* (U24) GPMC0_AD15.VOUT0_DATA23 */
+		>;
+	};
 };
 
 &mcu_pmx0 {
@@ -670,6 +749,46 @@ &main_i2c2 {
 	pinctrl-0 = <&i2c2_1v8_pins_default>;
 	clock-frequency = <100000>;
 	status = "okay";
+
+	it66121: bridge-hdmi@4c {
+		compatible = "ite,it66121";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdmi_gpio_pins_default>;
+		reg = <0x4c>;
+
+		#sound-dai-cells = <0>;
+
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <36 IRQ_TYPE_EDGE_FALLING>;
+
+		vcn33-supply = <&vdd_3v3>;
+		vcn18-supply = <&buck2_reg>;
+		vrf12-supply = <&buck3_reg>;
+
+		reset-gpios = <&main_gpio0 21 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				it66121_in: endpoint {
+					bus-width = <24>;
+					remote-endpoint = <&dpi1_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				it66121_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
 };
 
 &main_i2c3 {
@@ -756,3 +875,42 @@ &main_uart6 {
 	pinctrl-0 = <&wifi_debug_uart_pins_default>;
 	status = "okay";
 };
+
+&dss {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss0_pins_default>;
+};
+
+&dss_ports {
+	/* VP2: DPI Output */
+	port@1 {
+		reg = <1>;
+
+		dpi1_out: endpoint {
+			remote-endpoint = <&it66121_in>;
+		};
+	};
+};
+
+&mcasp1 {
+	status = "okay";
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp_hdmi_pins_default>;
+
+	auxclk-fs-ratio = <2177>;
+
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+
+	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+	       1 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};
Signature · 1 line
2.40.1
#8 lore raw

Re: [PATCH v4 5/6] arm64: dts: ti: k3-am625-beagleplay: Add HDMI support

Quoted 125 lines · Aradhya Bhatia

From: Nishanth Menon <[email protected]>

The DSS outputs DPI signals via its second video port (VP2). The DPI output from DSS is 24 bits (RGB888) and is forwarded to an HDMI transmitter (ITE-IT66121) on the BeaglePlay platform. For audio output, BeaglePlay uses mcasp1.

Add pinmux info for DSS DPI signals.

Further, add support for HDMI audio and video output.

[a-bhatia1: Edit sound node properties and HDMI node and label names]
---
  .../arm64/boot/dts/ti/k3-am625-beagleplay.dts | 158 ++++++++++++++++++
  1 file changed, 158 insertions(+)
arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts +85 -0
index e07ddff22e07..582410be9570 100644
@@ -192,6 +192,34 @@ usr: button-usr {
 
  	};
 
+	hdmi0: connector-hdmi {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "a";
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&it66121_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "it66121 HDMI";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&hdmi_dailink_master>;
+		simple-audio-card,frame-master = <&hdmi_dailink_master>;
+
+		hdmi_dailink_master: simple-audio-card,cpu {
+			sound-dai = <&mcasp1>;
+			system-clock-direction-out;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&it66121>;
+		};
+	};
+
  	/* Workaround for errata i2329 - just use mdio bitbang */
  	mdio0: mdio {
  		compatible = "virtual,mdio-gpio";
@@ -422,6 +450,57 @@ pmic_irq_pins_default: pmic-irq-default-pins {
  			AM62X_IOPAD(0x01f4, PIN_INPUT_PULLUP, 0) /* (D16) EXTINTn */
  		>;
  	};
+
+	hdmi_gpio_pins_default: hdmi-gpio-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0094, PIN_INPUT_PULLUP | PIN_DEBOUNCE_CONF6, 7) /* (N20) GPMC0_BE1n.GPIO0_36 */
+			AM62X_IOPAD(0x0054, PIN_OUTPUT_PULLUP, 7) /* (P21) GPMC0_AD6.GPIO0_21 */
+		>;
+	};
+
+	mcasp_hdmi_pins_default: mcasp-hdmi-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0090, PIN_INPUT, 2) /* (M24) GPMC0_BE0n_CLE.MCASP1_ACLKX */
+			AM62X_IOPAD(0x0098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
+			AM62X_IOPAD(0x008c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEn.MCASP1_AXR0 */
+			AM62X_IOPAD(0x0088, PIN_INPUT, 2) /* (L24) GPMC0_OEn_REn.MCASP1_AXR1 */
+			AM62X_IOPAD(0x0084, PIN_INPUT, 2) /* (L23) GPMC0_ADVn_ALE.MCASP1_AXR2 */
+			AM62X_IOPAD(0x007c, PIN_INPUT, 2) /* (P25) GPMC0_CLK.MCASP1_AXR3 */
+		>;
+	};
+
+	dss0_pins_default: dss0-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0100, PIN_OUTPUT, 0) /* (AC25) VOUT0_VSYNC */
+			AM62X_IOPAD(0x00f8, PIN_OUTPUT, 0) /* (AB24) VOUT0_HSYNC */
+			AM62X_IOPAD(0x0104, PIN_OUTPUT, 0) /* (AC24) VOUT0_PCLK */
+			AM62X_IOPAD(0x00fc, PIN_OUTPUT, 0) /* (Y20) VOUT0_DE */
+			AM62X_IOPAD(0x00b8, PIN_OUTPUT, 0) /* (U22) VOUT0_DATA0 */
+			AM62X_IOPAD(0x00bc, PIN_OUTPUT, 0) /* (V24) VOUT0_DATA1 */
+			AM62X_IOPAD(0x00c0, PIN_OUTPUT, 0) /* (W25) VOUT0_DATA2 */
+			AM62X_IOPAD(0x00c4, PIN_OUTPUT, 0) /* (W24) VOUT0_DATA3 */
+			AM62X_IOPAD(0x00c8, PIN_OUTPUT, 0) /* (Y25) VOUT0_DATA4 */
+			AM62X_IOPAD(0x00cc, PIN_OUTPUT, 0) /* (Y24) VOUT0_DATA5 */
+			AM62X_IOPAD(0x00d0, PIN_OUTPUT, 0) /* (Y23) VOUT0_DATA6 */
+			AM62X_IOPAD(0x00d4, PIN_OUTPUT, 0) /* (AA25) VOUT0_DATA7 */
+			AM62X_IOPAD(0x00d8, PIN_OUTPUT, 0) /* (V21) VOUT0_DATA8 */
+			AM62X_IOPAD(0x00dc, PIN_OUTPUT, 0) /* (W21) VOUT0_DATA9 */
+			AM62X_IOPAD(0x00e0, PIN_OUTPUT, 0) /* (V20) VOUT0_DATA10 */
+			AM62X_IOPAD(0x00e4, PIN_OUTPUT, 0) /* (AA23) VOUT0_DATA11 */
+			AM62X_IOPAD(0x00e8, PIN_OUTPUT, 0) /* (AB25) VOUT0_DATA12 */
+			AM62X_IOPAD(0x00ec, PIN_OUTPUT, 0) /* (AA24) VOUT0_DATA13 */
+			AM62X_IOPAD(0x00f0, PIN_OUTPUT, 0) /* (Y22) VOUT0_DATA14 */
+			AM62X_IOPAD(0x00f4, PIN_OUTPUT, 0) /* (AA21) VOUT0_DATA15 */
+			AM62X_IOPAD(0x005c, PIN_OUTPUT, 1) /* (R24) GPMC0_AD8.VOUT0_DATA16 */
+			AM62X_IOPAD(0x0060, PIN_OUTPUT, 1) /* (R25) GPMC0_AD9.VOUT0_DATA17 */
+			AM62X_IOPAD(0x0064, PIN_OUTPUT, 1) /* (T25) GPMC0_AD10.VOUT0_DATA18 */
+			AM62X_IOPAD(0x0068, PIN_OUTPUT, 1) /* (R21) GPMC0_AD11.VOUT0_DATA19 */
+			AM62X_IOPAD(0x006c, PIN_OUTPUT, 1) /* (T22) GPMC0_AD12.VOUT0_DATA20 */
+			AM62X_IOPAD(0x0070, PIN_OUTPUT, 1) /* (T24) GPMC0_AD13.VOUT0_DATA21 */
+			AM62X_IOPAD(0x0074, PIN_OUTPUT, 1) /* (U25) GPMC0_AD14.VOUT0_DATA22 */
+			AM62X_IOPAD(0x0078, PIN_OUTPUT, 1) /* (U24) GPMC0_AD15.VOUT0_DATA23 */
+		>;
+	};
  };
 
  &mcu_pmx0 {
@@ -670,6 +749,46 @@ &main_i2c2 {
  	pinctrl-0 = <&i2c2_1v8_pins_default>;
  	clock-frequency = <100000>;
  	status = "okay";
+
+	it66121: bridge-hdmi@4c {
+		compatible = "ite,it66121";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdmi_gpio_pins_default>;
+		reg = <0x4c>;

arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts &main_i2c2 { · line 767

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts +10 -0
+
+		#sound-dai-cells = <0>;
+
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <36 IRQ_TYPE_EDGE_FALLING>;
+
+		vcn33-supply = <&vdd_3v3>;
+		vcn18-supply = <&buck2_reg>;
+		vrf12-supply = <&buck3_reg>;
+

Fix unnecessary line breaks in this node.

Quoted 51 lines
arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts +44 -0
+		reset-gpios = <&main_gpio0 21 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				it66121_in: endpoint {
+					bus-width = <24>;
+					remote-endpoint = <&dpi1_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				it66121_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
  };
 
  &main_i2c3 {
@@ -756,3 +875,42 @@ &main_uart6 {
  	pinctrl-0 = <&wifi_debug_uart_pins_default>;
  	status = "okay";
  };
+
+&dss {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss0_pins_default>;
+};
+
+&dss_ports {
+	/* VP2: DPI Output */
+	port@1 {
+		reg = <1>;
+
+		dpi1_out: endpoint {
+			remote-endpoint = <&it66121_in>;
+		};
+	};
+};
+
+&mcasp1 {
+	status = "okay";

arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts &main_uart6 { · line 907

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts +10 -0
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp_hdmi_pins_default>;
+
+	auxclk-fs-ratio = <2177>;
+
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+

Fix unnecessary line breaks in this node.

arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts &main_uart6 { · line 916

Quoted 9 lines
arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts +9 -0
+	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+	       1 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#9 lore raw

PATCH v4 6/6 arm64: defconfig: Enable ITE_IT66121 HDMI transmitter

In reply to Aradhya Bhatia

Enable CONFIG_DRM_ITE_IT66121.

ILITEK ITE-IT66121 is an HDMI transmitter, which takes parallel video signals (DPI) as input. It is being used on TI's AM625 SoC based BeaglePlay platform[0].

[0]: https://beagleboard.org/play

---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/configs/defconfig +1 -0
index bf13d5c46578..87c5d2273535 100644
@@ -840,6 +840,7 @@ CONFIG_DRM_PANEL_VISIONOX_VTDR6130=m
 CONFIG_DRM_LONTIUM_LT8912B=m
 CONFIG_DRM_LONTIUM_LT9611=m
 CONFIG_DRM_LONTIUM_LT9611UXC=m
+CONFIG_DRM_ITE_IT66121=m
 CONFIG_DRM_NWL_MIPI_DSI=m
 CONFIG_DRM_PARADE_PS8640=m
 CONFIG_DRM_SII902X=m
Signature · 1 line
2.40.1