Skip to contentSkip to conversation

Add TPS6594 PMIC support on several boards

PATCH Applied Jai Luthra 2 participants 10 messages Aug 9, 2023 – Aug 10, 2023

Subsystems (2)
lore
Share & tools
lore

Jai Luthra

author
#0 lore raw

v6 cover Add TPS6594 PMIC support on several boards

TPS6594 is a Power Management IC which provides regulators and others features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and PFSM (Pre-configurable Finite State Machine). The SoC and the PMIC can communicate through the I2C or SPI interfaces.
TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives.

This serie adds device tree nodes for TI TPS6594 PMICs found in the following boards:
- J721EXSOMXEVM:

- J721S2XSOMXEVM:

- J7200XSOMXEVM:

- AM62A-SKEVM:

- J784S4XEVM

---
Changes from v5:
https://lore.kernel.org/all/[email protected]
- Range-diff: http://0x0.st/H_fD.diff
- Reword the patch fixing interrupt ranges for mcu domain gpio intr, and add Fixes: tag
- Also fix interrupt ranges for main domain gpio intr in the same patch
- Change pinctrl node names to end in -pins to fix dtbs_check warnings
- (New Patch) Enable TPS6594 in defconfig

Changes from v4:
https://lore.kernel.org/all/[email protected]/
- Range-diff: https://0x0.st/H_L7.diff
- Rebased on top of linux-next
- Fix min voltage on vdd_usb_3v3 regulator (ldo2) on j721e-som
- Use 3-hex-digit format for pinctrl values

Changes from v3:
https://lore.kernel.org/all/[email protected]/
- Rebased on top of v6.5-rc1.
- Change pinctrl number for irq pin as wkup_pmx0 was split on some boards.
- Use already present wkup_i2c0 node instead of creating a new one.

Changes from v2:
https://lore.kernel.org/lkml/[email protected]/
- Change node name as per Krzysztof review.
- Add a fix for the interrupt range of wakeup gpio used by TPS6594 pmic on J784S4.
The interruptions of the PMIC were not working before that.
- Remove dependencies on other patch series as that was a mistake, see
https://lore.kernel.org/lkml/CRYY2V3HJ0CP.96JQ18PLZB3C@burritosblues/

Changes from v1:
https://lore.kernel.org/lkml/[email protected]/
- Harmonize regulators names across the different boards.
- Adjust AVS voltage range.
- Remove some outdated comments.
- Add PMIC to J784S4 board.
- Compatible string modified to match dt-bindings.
- Add gpio-controller and gpio-cells properties.

---
Apelete Seketeli (1):
arm64: dts: ti: k3-j784s4: Fix interrupt ranges for wkup & main gpio

Esteban Blanc (2):

      arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
      arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs

Jai Luthra (1):
arm64: defconfig: Enable TPS6593 PMIC for SK-AM62A

Jerome Neanne (2):

      arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
      arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC

Julien Panis (1):

      arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts          |  95 +++++++++++
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi      | 157 ++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi      | 163 +++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi     | 199 +++++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts         | 104 ++++++++++++
 arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi       |   2 +-
 arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi |   2 +-
 arch/arm64/configs/defconfig                     |   1 +
 8 files changed, 721 insertions(+), 2 deletions(-)

---
base-commit: 21ef7b1e17d039053edaeaf41142423810572741
change-id: 20230809-tps6594-e450b5738e66

Best regards,

Signature · 1 line
Jai Luthra <[email protected]>
author
#1 lore raw

PATCH v6 1/7 arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs

From: Esteban Blanc <[email protected]>

This patch adds support for TPS6594 PMIC family on wakup I2C0 bus. Theses devices provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor) which monitors the SoC error output signal, and a PFSM (Pre-configurable Finite State Machine) which manages the operational modes of the PMIC.

---
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 157 ++++++++++++++++++++++++++++
 1 file changed, 157 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi +157 -0
index b37f4f88ece4..51ed611585dd 100644
@@ -127,6 +127,14 @@ J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
 	};
 };
 
+&wkup_pmx3 {
+	pmic_irq_pins_default: pmic-irq-default-pins {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x01c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */
+		>;
+	};
+};
+
 &main_pmx0 {
 	main_i2c0_pins_default: main-i2c0-default-pins {
 		pinctrl-single,pins = <
@@ -264,6 +272,155 @@ eeprom@50 {
 		compatible = "atmel,24c256";
 		reg = <0x50>;
 	};
+
+	tps659414: pmic@48 {
+		compatible = "ti,tps6594-q1";
+		reg = <0x48>;
+		ti,primary-pmic;
+		system-power-controller;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1-supply = <&vsys_3v3>;
+		buck2-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			bucka1: buck1 {
+				regulator-name = "vda_mcu_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka2: buck2 {
+				regulator-name = "vdd_mcuio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka3: buck3 {
+				regulator-name = "vdd_mcu_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka4: buck4 {
+				regulator-name = "vdd_ddr_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka5: buck5 {
+				regulator-name = "vdd_phyio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa1: ldo1 {
+				regulator-name = "vdd1_lpddr4_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa2: ldo2 {
+				regulator-name = "vda_dll_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa3: ldo3 {
+				regulator-name = "vdd_wk_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa4: ldo4 {
+				regulator-name = "vda_pll_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	lp876441: pmic@4c {
+		compatible = "ti,lp8764-q1";
+		reg = <0x4c>;
+		system-power-controller;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1-supply = <&vsys_3v3>;
+		buck2-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+
+		regulators: regulators {
+			buckb1: buck1 {
+				regulator-name = "vdd_cpu_avs";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <900000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buckb2: buck2 {
+				regulator-name = "vdd_ram_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb3: buck3 {
+				regulator-name = "vdd_core_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb4: buck4 {
+				regulator-name = "vdd_io_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
 };
 
 &ospi0 {
Signature · 1 line
2.41.0
author
#2 lore raw

PATCH v6 2/7 arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs

In reply to Jai Luthra

From: Esteban Blanc <[email protected]>

This patch adds support for TPS6594 PMIC family on wakup I2C0 bus. Theses devices provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor) which monitors the SoC error output signal, and a PFSM (Pre-configurable Finite State Machine) which manages the operational modes of the PMIC.

---
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++++++++++
 1 file changed, 199 insertions(+)
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi +199 -0
index a4006f328027..94b6162aba21 100644
@@ -70,6 +70,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
 	};
 };
 
+&wkup_pmx1 {
+	pmic_irq_pins_default: pmic-irq-default-pins {
+		pinctrl-single,pins = <
+			/* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+			J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 7)
+		>;
+	};
+};
+
 &wkup_pmx2 {
 	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
 		pinctrl-single,pins = <
@@ -106,6 +115,196 @@ eeprom@50 {
 		compatible = "atmel,24c256";
 		reg = <0x50>;
 	};
+
+	tps659411: pmic@48 {
+		compatible = "ti,tps6594-q1";
+		reg = <0x48>;
+		ti,primary-pmic;
+		system-power-controller;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1234-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			bucka1234: buck1234 {
+				regulator-name = "vdd_cpu_avs";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka5: buck5 {
+				regulator-name = "vdd_mcu_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa1: ldo1 {
+				regulator-name = "vdd_mcuwk_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa2: ldo2 {
+				regulator-name = "vdd_mcu_gpioret_3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa3: ldo3 {
+				regulator-name = "vdd_mcuio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa4: ldo4 {
+				regulator-name = "vda_mcu_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	tps659414: pmic@4c {
+		compatible = "ti,tps6594-q1";
+		reg = <0x4c>;
+		system-power-controller;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1-supply = <&vsys_3v3>;
+		buck2-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			buckb1: buck1 {
+				regulator-name = "vdd_io_1v8_reg";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buckb2: buck2 {
+				regulator-name = "vdd_fpd_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb3: buck3 {
+				regulator-name = "vdd_phy_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb4: buck4 {
+				regulator-name = "vdd_ddr_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb5: buck5 {
+				regulator-name = "vdd_ram_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob1: ldo1 {
+				regulator-name = "vdd_wk_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob2: ldo2 {
+				regulator-name = "vdd_gpioret_3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob3: ldo3 {
+				regulator-name = "vda_dll_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob4: ldo4 {
+				regulator-name = "vda_pll_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	lp876411: pmic@58 {
+		compatible = "ti,lp8764-q1";
+		reg = <0x58>;
+		system-power-controller;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1234-supply = <&vsys_3v3>;
+
+		regulators {
+			buckc1234: buck1234 {
+				regulator-name = "vdd_core_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
 };
 
 &main_i2c0 {
Signature · 1 line
2.41.0
author
#3 lore raw

PATCH v6 3/7 arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs

In reply to Jai Luthra

From: Jerome Neanne <[email protected]>

This patch adds support for TPS6594 PMIC family on wakup I2C0 bus. Theses devices provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor) which monitors the SoC error output signal, and a PFSM (Pre-configurable Finite State Machine) which manages the operational modes of the PMIC.

---
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 163 ++++++++++++++++++++++++++++
 1 file changed, 163 insertions(+)
arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi +163 -0
index e90e43202546..21f350cd9a45 100644
@@ -152,6 +152,12 @@ J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
 		>;
 	};
 
+	pmic_irq_pins_default: pmic-irq-default-pins {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x0d4, PIN_INPUT, 7) /* (G26) WKUP_GPIO0_9 */
+		>;
+	};
+
 	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
@@ -199,6 +205,163 @@ eeprom@50 {
 		compatible = "atmel,24c256";
 		reg = <0x50>;
 	};
+
+	tps659413: pmic@48 {
+		compatible = "ti,tps6594-q1";
+		reg = <0x48>;
+		system-power-controller;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		ti,primary-pmic;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck12-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			bucka12: buck12 {
+				regulator-name = "vdd_cpu_avs";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka3: buck3 {
+				regulator-name = "vdd_mcu_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka4: buck4 {
+				regulator-name = "vdd_ddr_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka5: buck5 {
+				regulator-name = "vdd_phyio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa1: ldo1 {
+				regulator-name = "vdd1_lpddr4_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa2: ldo2 {
+				regulator-name = "vdd_mcuio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa3: ldo3 {
+				regulator-name = "vdda_dll_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa4: ldo4 {
+				regulator-name = "vda_mcu_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	tps659411: pmic@4c {
+		compatible = "ti,tps6594-q1";
+		reg = <0x4c>;
+		system-power-controller;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1234-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			buckb1234: buck1234 {
+				regulator-name = "vdd_core_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb5: buck5 {
+				regulator-name = "vdd_ram_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob1: ldo1 {
+				regulator-name = "vdd_sd_dv";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob2: ldo2 {
+				regulator-name = "vdd_usb_3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob3: ldo3 {
+				regulator-name = "vdd_io_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob4: ldo4 {
+				regulator-name = "vda_pll_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
 };
 
 &ospi0 {
Signature · 1 line
2.41.0
author
#4 lore raw

PATCH v6 4/7 arm64: dts: ti: k3-j784s4: Fix interrupt ranges for wkup & main gpio

In reply to Jai Luthra

From: Apelete Seketeli <[email protected]>

This patch fixes the interrupt range for wakeup and main domain gpio interrupt routers. They were wrongly subtracted by 32 instead of following what is defined in the interrupt map in the TRM (Table 9-35).

Fixes 4664ebd8346a ("arm64: dts: ti: Add initial support for J784S4 SoC")
---
 arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi       | 2 +-
 arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi +1 -1
index a04c44708a09..013cf4ed98d8 100644
@@ -60,7 +60,7 @@ main_gpio_intr: interrupt-controller@a00000 {
 		#interrupt-cells = <1>;
 		ti,sci = <&sms>;
 		ti,sci-dev-id = <10>;
-		ti,interrupt-ranges = <8 360 56>;
+		ti,interrupt-ranges = <8 392 56>;
 	};
 
 	main_pmx0: pinctrl@11c000 {
arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi +1 -1
index 740ee794d7b9..77a45f97e28b 100644
@@ -107,7 +107,7 @@ wkup_gpio_intr: interrupt-controller@42200000 {
 		#interrupt-cells = <1>;
 		ti,sci = <&sms>;
 		ti,sci-dev-id = <177>;
-		ti,interrupt-ranges = <16 928 16>;
+		ti,interrupt-ranges = <16 960 16>;
 	};
 
 	/* MCU_TIMERIO pad input CTRLMMR_MCU_TIMER*_CTRL registers */
Signature · 1 line
2.41.0
author
#5 lore raw

PATCH v6 5/7 arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC

In reply to Jai Luthra

From: Jerome Neanne <[email protected]>

This patch adds support for TPS6593 PMIC on wkup I2C0 bus. This device provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor) which monitors the SoC error output signal, and a PFSM (Pre-configurable Finite State Machine) which manages the operational modes of the PMIC.

---
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 104 +++++++++++++++++++++++++++++++
 1 file changed, 104 insertions(+)
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts +104 -0
index edc1009b2d1e..29202ef40f78 100644
@@ -251,6 +251,10 @@ vdd_sd_dv: regulator-TLV71033 {
 	};
 };
 
+&wkup_gpio0 {
+	status = "okay";
+};
+
 &main_pmx0 {
 	main_uart8_pins_default: main-uart8-default-pins {
 		pinctrl-single,pins = <
@@ -365,6 +369,17 @@ J784S4_WKUP_IOPAD(0x170, PIN_INPUT, 0) /* (Y36) MCU_ADC1_AIN7 */
 	};
 };
 
+&wkup_pmx1 {
+	status = "okay";
+
+	pmic_irq_pins_default: pmic-irq-default-pins {
+		pinctrl-single,pins = <
+			/* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
+		>;
+	};
+};
+
 &wkup_pmx0 {
 	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
 		pinctrl-single,pins = <
@@ -423,6 +438,95 @@ eeprom@50 {
 		compatible = "atmel,24c256";
 		reg = <0x50>;
 	};
+
+	tps659413: pmic@48 {
+		compatible = "ti,tps6594-q1";
+		reg = <0x48>;
+		system-power-controller;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+		ti,primary-pmic;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck12-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			bucka12: buck12 {
+				regulator-name = "vdd_ddr_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka3: buck3 {
+				regulator-name = "vdd_ram_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka4: buck4 {
+				regulator-name = "vdd_io_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka5: buck5 {
+				regulator-name = "vdd_mcu_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa1: ldo1 {
+				regulator-name = "vdd_mcuio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa2: ldo2 {
+				regulator-name = "vdd_mcuio_3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa3: ldo3 {
+				regulator-name = "vds_dll_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa4: ldo4 {
+				regulator-name = "vda_mcu_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
 };
 
 &mcu_uart0 {
Signature · 1 line
2.41.0
author
#6 lore raw

PATCH v6 6/7 arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC

In reply to Jai Luthra

From: Julien Panis <[email protected]>

This patch adds support for TPS6593 PMIC on main I2C0 bus. This device provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor) which monitors the SoC error output signal, and a PFSM (Pre-configurable Finite State Machine) which manages the operational modes of the PMIC.

---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 95 +++++++++++++++++++++++++++++++++
 1 file changed, 95 insertions(+)
arch/arm64/boot/dts/ti/k3-am62a7-sk.dts +95 -0
index cff283c75f8e..2616acab8c0e 100644
@@ -221,6 +221,20 @@ AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
 	};
 };
 
+&mcu_pmx0 {
+	status = "okay";
+
+	pmic_irq_pins_default: pmic-irq-default-pins {
+		pinctrl-single,pins = <
+			AM62AX_MCU_IOPAD(0x000, PIN_INPUT, 7) /* (E11) MCU_GPIO0_0 */
+		>;
+	};
+};
+
+&mcu_gpio0 {
+	status = "okay";
+};
+
 &main_i2c0 {
 	status = "okay";
 	pinctrl-names = "default";
@@ -244,6 +258,87 @@ usb_con_hs: endpoint {
 			};
 		};
 	};
+
+	tps659312: pmic@48 {
+		compatible = "ti,tps6593-q1";
+		reg = <0x48>;
+		ti,primary-pmic;
+		system-power-controller;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&mcu_gpio0>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+		buck123-supply = <&vcc_3v3_sys>;
+		buck4-supply = <&vcc_3v3_sys>;
+		buck5-supply = <&vcc_3v3_sys>;
+		ldo1-supply = <&vcc_3v3_sys>;
+		ldo2-supply = <&vcc_3v3_sys>;
+		ldo3-supply = <&buck5>;
+		ldo4-supply = <&vcc_3v3_sys>;
+
+		regulators {
+			buck123: buck123 {
+				regulator-name = "vcc_core";
+				regulator-min-microvolt = <715000>;
+				regulator-max-microvolt = <895000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4: buck4 {
+				regulator-name = "vcc_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5: buck5 {
+				regulator-name = "vcc_1v8_sys";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1: ldo1 {
+				regulator-name = "vddshv5_sdio";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2: ldo2 {
+				regulator-name = "vpp_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3: ldo3 {
+				regulator-name = "vcc_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4: ldo4 {
+				regulator-name = "vdda_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
 };
 
 &main_i2c1 {
Signature · 1 line
2.41.0
author
#7 lore raw

PATCH v6 7/7 arm64: defconfig: Enable TPS6593 PMIC for SK-AM62A

In reply to Jai Luthra

SK-AM62A-LP uses TPS6593x PMIC (interfaced over I2C) to power the SoC and various other peripherals on the board [1].

Specifically, the audio codec (TLV320AIC3106) on the board relies on the PMIC for the DVDD (1.8V) supply.

[1]: https://www.ti.com/lit/zip/sprr459

---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/configs/defconfig +1 -0
index bf13d5c46578..9f7697caa5ca 100644
@@ -719,6 +719,7 @@ CONFIG_MFD_SEC_CORE=y
 CONFIG_MFD_SL28CPLD=y
 CONFIG_RZ_MTU3=y
 CONFIG_MFD_TPS65219=y
+CONFIG_MFD_TPS6594_I2C=m
 CONFIG_MFD_TI_AM335X_TSCADC=m
 CONFIG_MFD_ROHM_BD718XX=y
 CONFIG_MFD_WCD934X=m
Signature · 1 line
2.41.0
maintainer
#8 lore raw
In reply to Jai Luthra
Quoted 4 lines · Jai Luthra
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts          |  95 +++++++++++
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi      | 157 ++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi      | 163 +++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi     | 199 +++++++++++++++++++++++

Sigh.. Thanks Jai for stepping and trying to make this work, but I think this series is a lot out of whack. Apparently somewhere in this series is a patch for j721s2 that breaks proper boot. I spent quite a while bisecting across boards to find it, So, I am just going to skip this series for this release (and dependencies)

Next time for this series: I recommend submitter provide test logs for every single platform touched.

https://gist.github.com/nmenon/72e5f9b344e9207863d93491f5bf4f8e

I have'nt debugged, but typically that looks like some one decided to pull the voltage low on a key rail.

Let me see if I can pick the interrupt range fix at least since should'nt be dependent on this.

Quoted 5 lines
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts         | 104 ++++++++++++
 arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi       |   2 +-
 arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi |   2 +-
 arch/arm64/configs/defconfig                     |   1 +
 8 files changed, 721 insertions(+), 2 deletions(-)
Quoted 8 lines

---
base-commit: 21ef7b1e17d039053edaeaf41142423810572741
change-id: 20230809-tps6594-e450b5738e66

Best regards,

Signature · 1 line
Jai Luthra <[email protected]>

bisect log: (commit sha's dont mean a thing.. but anyways..)
git bisect start
# good: [f2e72716f089d6fcc4bf7b8cb7ac874b79ed05b1] iommu: dev->iommu->iommu_dev must be set before ops->device_group() git bisect good f2e72716f089d6fcc4bf7b8cb7ac874b79ed05b1
# bad: [31f83ee5e42290c39e0bce42118ad1267eaf2790] arm64: dts: ti: k3-am64: Enable TSCADC nodes at the board level git bisect bad 31f83ee5e42290c39e0bce42118ad1267eaf2790
# bad: [f51a52fc98cddb7b99ecb19d86c40845f7e8d91e] arm64: dts: ti: k3-am62a7-sk: Split vcc_3v3 regulators git bisect bad f51a52fc98cddb7b99ecb19d86c40845f7e8d91e
# good: [0cc1aecdc1024eced6914f015dbc43c28f5ac6aa] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs git bisect good 0cc1aecdc1024eced6914f015dbc43c28f5ac6aa
# good: [8b4e4f23f60df9c8aadb0e26cb86b13735ed810b] arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC git bisect good 8b4e4f23f60df9c8aadb0e26cb86b13735ed810b
# bad: [38ff20140c2cf09ba140234732dd03a9743ebd32] arm64: defconfig: Enable TPS6593 PMIC for SK-AM62A git bisect bad 38ff20140c2cf09ba140234732dd03a9743ebd32
# good: [3e98e865a6135bef7d801b5c5236a42a0ef1bff2] arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC git bisect good 3e98e865a6135bef7d801b5c5236a42a0ef1bff2

# first bad commit: [38ff20140c2cf09ba140234732dd03a9743ebd32] arm64: defconfig: Enable TPS6593 PMIC for SK-AM62A
Signature · 3 lines
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D
maintainer Applied
#9 lore raw

Re: (subset) [PATCH v6 0/7] Add TPS6594 PMIC support on several boards

In reply to Jai Luthra

Hi Jai Luthra,

Quoted 14 lines · Jai Luthra

TPS6594 is a Power Management IC which provides regulators and others features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and PFSM (Pre-configurable Finite State Machine). The SoC and the PMIC can communicate through the I2C or SPI interfaces.
TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives.

This serie adds device tree nodes for TI TPS6594 PMICs found in the following boards:
- J721EXSOMXEVM:
- J721S2XSOMXEVM:
- J7200XSOMXEVM:
- AM62A-SKEVM:
- J784S4XEVM

Quoted 1 line

[...]

As I mentioned in the previous response - this needs much deeper review - I recommend actual test log and board schematics links to cross verify we are modifying the correct platforms in the right manner. So, I am not picking up the defconfig either as it did'nt make sense to pick it up without dts actually using it.

Only patch I could reasonably pick is the one below (ideally should have been sent independent of the series, but, ok.).

I have applied the following to branch ti-k3-dts-next on [1]. Thank you!

[4/7] arm64: dts: ti: k3-j784s4: Fix interrupt ranges for wkup & main gpio

      commit: 05a1f130101e7a49ff1e8734939facd43596ea26

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git

Signature · 3 lines
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D