net: stmmac: add new features to xgmac
Subsystems (5)
v5 cover net: stmmac: add new features to xgmac
This series add below new features to xgmac:
correct RX COE parsing
add more feature parsing from hw cap enlarge C22 ADDR and rx/tx channels support parse safety ce/ue irq from DT support per channel irq
Since v4:
- move "additionalItems" and "maxItems" a bit earlier to patch5 to fix "interrupt-names... is too long"
Since v3:
- collect Acked-by tag
- remove patch which enlarges the max XGMAC C22 ADDR to 31 since it's merged
- s/stmmac_request_irq_multi/stmmac_request_irq_multi_channel
- update the dt-binding to refelct the optional per-channel irq:
- use enum
- add additionalItems and maxItems to fix the "interrupt-names .. is too long"
Since v2:
- check per channel irq by (res->rx_irq[0] > 0 && res->tx_irq[0] > 0) rather than (res->rx_irq[0] && res->tx_irq[0])
- bypass if (irq <= 0) when request rx/tx irq
Since v1:
- remove "_irq" suffix from safety irqs dt binding
- remove "snps,per-channel-interrupt" dt binding, check the channel irq instead.
- more renaming about "msi" to reflect per channel irq isn't MSI specific
Jisheng Zhang (9):
net: stmmac: correct RX COE parsing for xgmac
net: stmmac: xgmac: add more feature parsing from hw cap
net: stmmac: enlarge max rx/tx queues and channels to 16
net: stmmac: reflect multi irqs for tx/rx channels and mac and safety
net: stmmac: xgmac: support per-channel irq
dt-bindings: net: snps,dwmac: add safety irq support
net: stmmac: platform: support parsing safety irqs from DT
dt-bindings: net: snps,dwmac: add per channel irq support
net: stmmac: platform: support parsing per channel irq from DT
.../devicetree/bindings/net/snps,dwmac.yaml | 77 ++++++++++++++++++- .../net/ethernet/stmicro/stmmac/dwmac-intel.c | 4 +- .../net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +- .../net/ethernet/stmicro/stmmac/dwxgmac2.h | 2 + .../ethernet/stmicro/stmmac/dwxgmac2_core.c | 5 +- .../ethernet/stmicro/stmmac/dwxgmac2_dma.c | 34 ++++---- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 56 +++++++------- .../ethernet/stmicro/stmmac/stmmac_platform.c | 35 +++++++++ include/linux/stmmac.h | 10 +-- 9 files changed, 172 insertions(+), 53 deletions(-)
Signature · 1 line
2.40.1
PATCH v5 1/9 net: stmmac: correct RX COE parsing for xgmac
xgmac can support RX COE, but there's no two kinds of COE, I.E type 1 and type 2 COE.
--- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1 -1
@@ -7035,7 +7035,7 @@ static int stmmac_hw_init(struct stmmac_priv *priv)if (priv->plat->rx_coe) { priv->hw->rx_csum = priv->plat->rx_coe;dev_info (priv->device,"RX Checksum Offload Engine supported\n" ); -if (priv->synopsys_id <DWMAC_CORE_4_00 ) +if (priv->synopsys_id <DWMAC_CORE_4_00 && !priv->plat->has_xgmac)dev_info (priv->device,"COE Type %d\n" , priv->hw->rx_csum); }if (priv->plat->tx_coe)
Signature · 1 line
2.40.1
Re: [PATCH net-next v5 1/9] net: stmmac: correct RX COE parsing for xgmac
Quoted 5 lines · Jisheng Zhang
xgmac can support RX COE, but there's no two kinds of COE, I.E type 1 and type 2 COE.
Signed-off-by Jisheng Zhang <[email protected]>Acked-by Alexandre TORGUE <[email protected]>
-Serge(y)
Quoted 21 lines
--- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1
-1@@ -7035,7 +7035,7 @@ static int stmmac_hw_init(struct stmmac_priv *priv)if (priv->plat->rx_coe) { priv->hw->rx_csum = priv->plat->rx_coe;dev_info (priv->device,"RX Checksum Offload Engine supported\n" ); -if (priv->synopsys_id <DWMAC_CORE_4_00 ) +if (priv->synopsys_id <DWMAC_CORE_4_00 && !priv->plat->has_xgmac)dev_info (priv->device,"COE Type %d\n" , priv->hw->rx_csum); }if (priv->plat->tx_coe)Signature · 1 line
2.40.1
PATCH v5 2/9 net: stmmac: xgmac: add more feature parsing from hw cap
In reply to Jisheng ZhangThe XGMAC_HWFEAT_GMIISEL bit also indicates whether support 10/100Mbps or not.
--- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c | 1 + 1 file changed, 1 insertion(+)
drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +1 -0
@@ -410,6 +410,7 @@ static int dwxgmac2_get_hw_feature(void __iomem *ioaddr, dma_cap->vlhash = (hw_cap &XGMAC_HWFEAT_VLHASH ) >>4 ; dma_cap->half_duplex = (hw_cap &XGMAC_HWFEAT_HDSEL ) >>3 ; dma_cap->mbps_1000 = (hw_cap &XGMAC_HWFEAT_GMIISEL ) >>1 ; + dma_cap->mbps_10_100 = (hw_cap &XGMAC_HWFEAT_GMIISEL ) >>1 ;/* MAC HW feature 1 */ hw_cap =readl (ioaddr +XGMAC_HW_FEATURE1 );
Signature · 1 line
2.40.1
Re: [PATCH net-next v5 2/9] net: stmmac: xgmac: add more feature parsing from hw cap
Quoted 5 lines · Jisheng Zhang
The
XGMAC_HWFEAT_GMIISELbit also indicates whether support 10/100Mbps or not.Signed-off-by Jisheng Zhang <[email protected]>Acked-by Alexandre TORGUE <[email protected]>
-Serge(y)
Quoted 20 lines
--- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c | 1 + 1 file changed, 1 insertion(+)drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +1
-0@@ -410,6 +410,7 @@ static int dwxgmac2_get_hw_feature(void __iomem *ioaddr, dma_cap->vlhash = (hw_cap &XGMAC_HWFEAT_VLHASH ) >>4 ; dma_cap->half_duplex = (hw_cap &XGMAC_HWFEAT_HDSEL ) >>3 ; dma_cap->mbps_1000 = (hw_cap &XGMAC_HWFEAT_GMIISEL ) >>1 ; + dma_cap->mbps_10_100 = (hw_cap &XGMAC_HWFEAT_GMIISEL ) >>1 ;/* MAC HW feature 1 */ hw_cap =readl (ioaddr +XGMAC_HW_FEATURE1 );Signature · 1 line
2.40.1
PATCH v5 3/9 net: stmmac: enlarge max rx/tx queues and channels to 16
In reply to Jisheng Zhangxgmac supports up to 16 rx/tx queues and up to 16 channels.
--- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c | 5 ++--- include/linux/stmmac.h | 6 +++--- 2 files changed, 5 insertions(+), 6 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c +2 -3
@@ -232,9 +232,8 @@ static void dwxgmac2_map_mtl_to_dma(struct mac_device_info *hw, u32 queue,void __iomem *ioaddr = hw->pcsr;u32 value, reg; - reg = (queue <4 ) ?XGMAC_MTL_RXQ_DMA_MAP0 :XGMAC_MTL_RXQ_DMA_MAP1 ; -if (queue >=4 ) - queue -=4 ; + reg =XGMAC_MTL_RXQ_DMA_MAP0 + (queue & ~0x3 ); + queue &=0x3 ; value =readl (ioaddr + reg); value &= ~XGMAC_QxMDMACH (queue);
include/linux/stmmac.h +3 -3
@@ -15,9 +15,9 @@#include <linux/platform_device.h> #include <linux/phy.h> -#define MTL_MAX_RX_QUEUES 8 -#define MTL_MAX_TX_QUEUES 8 -#define STMMAC_CH_MAX 8 +#define MTL_MAX_RX_QUEUES 16 +#define MTL_MAX_TX_QUEUES 16 +#define STMMAC_CH_MAX 16#define STMMAC_RX_COE_NONE 0#define STMMAC_RX_COE_TYPE1 1
Signature · 1 line
2.40.1
Re: [PATCH net-next v5 3/9] net: stmmac: enlarge max rx/tx queues and channels to 16
Quoted 30 lines · Jisheng Zhang
xgmac supports up to 16 rx/tx queues and up to 16 channels.
Signed-off-by Jisheng Zhang <[email protected]>Acked-by Alexandre TORGUE <[email protected]>--- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c | 5 ++--- include/linux/stmmac.h | 6 +++--- 2 files changed, 5 insertions(+), 6 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c +2
-3@@ -232,9 +232,8 @@ static void dwxgmac2_map_mtl_to_dma(struct mac_device_info *hw, u32 queue,void __iomem *ioaddr = hw->pcsr;u32 value, reg; - reg = (queue <4 ) ?XGMAC_MTL_RXQ_DMA_MAP0 :XGMAC_MTL_RXQ_DMA_MAP1 ; -if (queue >=4 ) - queue -=4 ; + reg =XGMAC_MTL_RXQ_DMA_MAP0 + (queue & ~0x3 ); + queue &=0x3 ; value =readl (ioaddr + reg); value &= ~XGMAC_QxMDMACH (queue);include/linux/stmmac.h +0
-0
include/linux/stmmac.h line 19
Quoted 8 lines
include/linux/stmmac.h +1
-3@@ -15,9 +15,9 @@#include <linux/platform_device.h> #include <linux/phy.h> -#define MTL_MAX_RX_QUEUES 8 -#define MTL_MAX_TX_QUEUES 8 -#define STMMAC_CH_MAX 8 +#define MTL_MAX_RX_QUEUES 16
In DW XGMAC 2.11a (Databook from 9.2015) number of MTL Rx queues is
limited with 12:
Number of Receive Queues Description: Specifies the number of receive queues.
Value Range: 1–12
Default Value: 1
Dependencies: This option is not available in XGMAC-CORE configurations. HDL Parameter Name: DWCXG_NUM_RXQ
Are you sure it's different in your case? Do you have a Synopsys HW manual with the DWCXG_NUM_RXQ parameter range limited to 16? What IP-core version is it about?
-Serge(y)
Quoted 9 lines
include/linux/stmmac.h +2
-0+#define MTL_MAX_TX_QUEUES 16 +#define STMMAC_CH_MAX 16#define STMMAC_RX_COE_NONE 0#define
STMMAC_RX_COE_TYPE11Signature · 1 line
2.40.1
PATCH v5 4/9 net: stmmac: reflect multi irqs for tx/rx channels and mac and safety
In reply to Jisheng ZhangThe IP supports per channel interrupt, when intel adds the per channel interrupt support, the per channel irq is from MSI vector, but this feature can also be supported on non-MSI platforms. Do some necessary renaming to reflects this fact.
--- .../net/ethernet/stmicro/stmmac/dwmac-intel.c | 4 +- .../net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 48 +++++++++---------- include/linux/stmmac.h | 4 +- 4 files changed, 29 insertions(+), 29 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c +2 -2
@@ -952,7 +952,7 @@ static int stmmac_config_single_msi(struct pci_dev *pdev, res->irq =pci_irq_vector (pdev,0 ); res->wol_irq = res->irq; - plat->flags &= ~STMMAC_FLAG_MULTI_MSI_EN ; + plat->flags &= ~STMMAC_FLAG_PERCH_IRQ_EN ;dev_info (&pdev->dev,"%s: Single IRQ enablement successful\n" , __func__);
@@ -1004,7 +1004,7 @@ static int stmmac_config_multi_msi(struct pci_dev *pdev,if (plat->msi_sfty_ue_vec <STMMAC_MSI_VEC_MAX ) res->sfty_ue_irq =pci_irq_vector (pdev, plat->msi_sfty_ue_vec); - plat->flags |=STMMAC_FLAG_MULTI_MSI_EN ; + plat->flags |=STMMAC_FLAG_PERCH_IRQ_EN ;dev_info (&pdev->dev,"%s: multi MSI enablement successful\n" , __func__);return 0 ;
drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c +1 -1
@@ -175,7 +175,7 @@ static void dwmac4_dma_init(void __iomem *ioaddr, value =readl (ioaddr +DMA_BUS_MODE ); -if (dma_cfg->multi_msi_en) { +if (dma_cfg->perch_irq_en) { value &= ~DMA_BUS_MODE_INTM_MASK ; value |= (DMA_BUS_MODE_INTM_MODE1 <<DMA_BUS_MODE_INTM_SHIFT ); }
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +24 -24
155 lines not on this page · raw message
include/linux/stmmac.h +2 -2
@@ -98,7 +98,7 @@ struct stmmac_dma_cfg {int mixed_burst;bool aal;bool eame; -bool multi_msi_en; +bool perch_irq_en;bool dche; };
@@ -213,7 +213,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_TSO_EN BIT(4)#define STMMAC_FLAG_SERDES_UP_AFTER_PHY_LINKUP BIT(5)#define STMMAC_FLAG_VLAN_FAIL_Q_EN BIT(6) -#define STMMAC_FLAG_MULTI_MSI_EN BIT(7) +#define STMMAC_FLAG_PERCH_IRQ_EN BIT(7)#define STMMAC_FLAG_EXT_SNAPSHOT_EN BIT(8)#define STMMAC_FLAG_INT_SNAPSHOT_EN BIT(9)#define STMMAC_FLAG_RX_CLK_RUNS_IN_LPI BIT(10)
Signature · 1 line
2.40.1
Re: [PATCH net-next v5 4/9] net: stmmac: reflect multi irqs for tx/rx channels and mac and safety
Quoted 53 lines · Jisheng Zhang
The IP supports per channel interrupt, when intel adds the per channel interrupt support, the per channel irq is from MSI vector, but this feature can also be supported on non-MSI platforms. Do some necessary renaming to reflects this fact.
Signed-off-by Jisheng Zhang <[email protected]>--- .../net/ethernet/stmicro/stmmac/dwmac-intel.c | 4 +- .../net/ethernet/stmicro/stmmac/dwmac4_dma.c | 2 +- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 48 +++++++++---------- include/linux/stmmac.h | 4 +- 4 files changed, 29 insertions(+), 29 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c +2
-2@@ -952,7 +952,7 @@ static int stmmac_config_single_msi(struct pci_dev *pdev, res->irq =pci_irq_vector (pdev,0 ); res->wol_irq = res->irq; - plat->flags &= ~STMMAC_FLAG_MULTI_MSI_EN ; + plat->flags &= ~STMMAC_FLAG_PERCH_IRQ_EN ;dev_info (&pdev->dev,"%s: Single IRQ enablement successful\n" , __func__);@@ -1004,7 +1004,7 @@ static int stmmac_config_multi_msi(struct pci_dev *pdev,if (plat->msi_sfty_ue_vec <STMMAC_MSI_VEC_MAX ) res->sfty_ue_irq =pci_irq_vector (pdev, plat->msi_sfty_ue_vec); - plat->flags |=STMMAC_FLAG_MULTI_MSI_EN ; + plat->flags |=STMMAC_FLAG_PERCH_IRQ_EN ;dev_info (&pdev->dev,"%s: multi MSI enablement successful\n" , __func__);return 0 ;drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c +1
-1@@ -175,7 +175,7 @@ static void dwmac4_dma_init(void __iomem *ioaddr, value =readl (ioaddr +DMA_BUS_MODE ); -if (dma_cfg->multi_msi_en) { +if (dma_cfg->perch_irq_en) { value &= ~DMA_BUS_MODE_INTM_MASK ; value |= (DMA_BUS_MODE_INTM_MODE1 <<DMA_BUS_MODE_INTM_SHIFT ); }drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0
-0
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c module_param(chain_mode, int, 0444); · line 134
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1
-3@@ -126,11 +126,11 @@ module_param(chain_mode, int, 0444);MODULE_PARM_DESC (chain_mode,"To use chain instead of ring mode" );static irqreturn_t stmmac_interrupt (int irq,void *dev_id); -/* For MSI interrupts handling */ +/* For multi channel interrupts handling */ static irqreturn_t stmmac_mac_interrupt (int irq,void *dev_id);static irqreturn_t stmmac_safety_interrupt (int irq,void *dev_id); -static irqreturn_t stmmac_msi_intr_tx (int irq,void *data); -static irqreturn_t stmmac_msi_intr_rx (int irq,void *data);
What about
+static irqreturn_t stmmac_tx_queue_interrupt(int irq, void *data); +static irqreturn_t stmmac_rx_queue_interrupt(int irq, void *data);
to have the names similar to stmmac_mac_interrupt() and stmmac_safety_interrupt().
BTW are you aware that the IRQs in subject are actually per-DMA-channel interrupts, not per-MTL-queue interrupts?
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c static void stmmac_free_irq(struct net_device *dev, · line 3524
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1
-1static void stmmac_reset_rx_queue (struct stmmac_priv *priv,u32 queue);static void stmmac_reset_tx_queue (struct stmmac_priv *priv,u32 queue);static void stmmac_reset_queues_param (struct stmmac_priv *priv);@@ -3520,7 +3520,7 @@ static void stmmac_free_irq(struct net_device *dev, } } -static int stmmac_request_irq_multi_msi (struct net_device *dev) +static int stmmac_request_irq_multi_channel (struct net_device *dev)
What about stmmac_request_irq_perch() to shorten out the name and have a unified "perch" suffix like in the flag STMMAC_FLAG_PERCH_IRQ_EN?
-Serge(y)
Quoted 175 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0
-0{struct stmmac_priv *priv =netdev_priv (dev);drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +20
-20enum request_irq_err irq_err;@@ -3537,7 +3537,7 @@ static int stmmac_request_irq_multi_msi(struct net_device *dev) 0, int_name, dev);if (unlikely (ret <0 )) {netdev_err (priv->dev, -"%s: alloc mac MSI %d (error: %d)\n" , +"%s: alloc mac irq %d (error: %d)\n" , __func__, dev->irq, ret); irq_err =REQ_IRQ_ERR_MAC ; goto irq_error;@@ -3554,7 +3554,7 @@ static int stmmac_request_irq_multi_msi(struct net_device *dev) 0, int_name, dev);if (unlikely (ret <0 )) {netdev_err (priv->dev, -"%s: alloc wol MSI %d (error: %d)\n" , +"%s: alloc wol irq %d (error: %d)\n" , __func__, priv->wol_irq, ret); irq_err =REQ_IRQ_ERR_WOL ; goto irq_error;@@ -3572,7 +3572,7 @@ static int stmmac_request_irq_multi_msi(struct net_device *dev) 0, int_name, dev);if (unlikely (ret <0 )) {netdev_err (priv->dev, -"%s: alloc lpi MSI %d (error: %d)\n" , +"%s: alloc lpi irq %d (error: %d)\n" , __func__, priv->lpi_irq, ret); irq_err =REQ_IRQ_ERR_LPI ; goto irq_error;@@ -3590,7 +3590,7 @@ static int stmmac_request_irq_multi_msi(struct net_device *dev) 0, int_name, dev);if (unlikely (ret <0 )) {netdev_err (priv->dev, -"%s: alloc sfty ce MSI %d (error: %d)\n" , +"%s: alloc sfty ce irq %d (error: %d)\n" , __func__, priv->sfty_ce_irq, ret); irq_err =REQ_IRQ_ERR_SFTY_CE ; goto irq_error;@@ -3608,14 +3608,14 @@ static int stmmac_request_irq_multi_msi(struct net_device *dev) 0, int_name, dev);if (unlikely (ret <0 )) {netdev_err (priv->dev, -"%s: alloc sfty ue MSI %d (error: %d)\n" , +"%s: alloc sfty ue irq %d (error: %d)\n" , __func__, priv->sfty_ue_irq, ret); irq_err =REQ_IRQ_ERR_SFTY_UE ; goto irq_error; } } -/* Request Rx MSI irq */ +/* Request Rx queue irq */ for (i =0 ; i < priv->plat->rx_queues_to_use; i++) {if (i >=MTL_MAX_RX_QUEUES )break ;@@ -3625,11 +3625,11 @@ static int stmmac_request_irq_multi_msi(struct net_device *dev) int_name = priv->int_name_rx_irq[i];sprintf (int_name,"%s:%s-%d" , dev->name,"rx" , i); ret =request_irq (priv->rx_irq[i], - stmmac_msi_intr_rx, + stmmac_queue_intr_rx,0 , int_name, &priv->dma_conf.rx_queue[i]);if (unlikely (ret <0 )) {netdev_err (priv->dev, -"%s: alloc rx-%d MSI %d (error: %d)\n" , +"%s: alloc rx-%d irq %d (error: %d)\n" , __func__, i, priv->rx_irq[i], ret); irq_err =REQ_IRQ_ERR_RX ; irq_idx = i;@@ -3640,7 +3640,7 @@ static int stmmac_request_irq_multi_msi(struct net_device *dev)irq_set_affinity_hint (priv->rx_irq[i], &cpu_mask); } -/* Request Tx MSI irq */ +/* Request Tx queue irq */ for (i =0 ; i < priv->plat->tx_queues_to_use; i++) {if (i >=MTL_MAX_TX_QUEUES )break ;@@ -3650,11 +3650,11 @@ static int stmmac_request_irq_multi_msi(struct net_device *dev) int_name = priv->int_name_tx_irq[i];sprintf (int_name,"%s:%s-%d" , dev->name,"tx" , i); ret =request_irq (priv->tx_irq[i], - stmmac_msi_intr_tx, + stmmac_queue_intr_tx,0 , int_name, &priv->dma_conf.tx_queue[i]);if (unlikely (ret <0 )) {netdev_err (priv->dev, -"%s: alloc tx-%d MSI %d (error: %d)\n" , +"%s: alloc tx-%d irq %d (error: %d)\n" , __func__, i, priv->tx_irq[i], ret); irq_err =REQ_IRQ_ERR_TX ; irq_idx = i;@@ -3729,8 +3729,8 @@ static int stmmac_request_irq(struct net_device *dev)int ret;/* Request the IRQ lines */ -if (priv->plat->flags &STMMAC_FLAG_MULTI_MSI_EN ) - ret =stmmac_request_irq_multi_msi (dev); +if (priv->plat->flags &STMMAC_FLAG_PERCH_IRQ_EN ) + ret =stmmac_request_irq_multi_channel (dev);else ret =stmmac_request_irq_single (dev);@@ -5945,7 +5945,7 @@ static irqreturn_t stmmac_safety_interrupt(int irq, void *dev_id)return IRQ_HANDLED ; } -static irqreturn_t stmmac_msi_intr_tx (int irq,void *data) +static irqreturn_t stmmac_queue_intr_tx (int irq,void *data) {struct stmmac_tx_queue *tx_q = (struct stmmac_tx_queue *)data;struct stmmac_dma_conf *dma_conf;@@ -5977,7 +5977,7 @@ static irqreturn_t stmmac_msi_intr_tx(int irq, void *data)return IRQ_HANDLED ; } -static irqreturn_t stmmac_msi_intr_rx (int irq,void *data) +static irqreturn_t stmmac_queue_intr_rx (int irq,void *data) {struct stmmac_rx_queue *rx_q = (struct stmmac_rx_queue *)data;struct stmmac_dma_conf *dma_conf;@@ -6014,12 +6014,12 @@ static void stmmac_poll_controller(struct net_device *dev)if (test_bit (STMMAC_DOWN , &priv->state))return ; -if (priv->plat->flags &STMMAC_FLAG_MULTI_MSI_EN ) { +if (priv->plat->flags &STMMAC_FLAG_PERCH_IRQ_EN ) {for (i =0 ; i < priv->plat->rx_queues_to_use; i++) -stmmac_msi_intr_rx (0 , &priv->dma_conf.rx_queue[i]); +stmmac_queue_intr_rx (0 , &priv->dma_conf.rx_queue[i]);for (i =0 ; i < priv->plat->tx_queues_to_use; i++) -stmmac_msi_intr_tx (0 , &priv->dma_conf.tx_queue[i]); +stmmac_queue_intr_tx (0 , &priv->dma_conf.tx_queue[i]); }else {disable_irq (dev->irq);stmmac_interrupt (dev->irq, dev);@@ -7300,8 +7300,8 @@ int stmmac_dvr_probe(struct device *device, priv->plat = plat_dat; priv->ioaddr = res->addr; priv->dev->base_addr = (unsigned long )res->addr; - priv->plat->dma_cfg->multi_msi_en = - (priv->plat->flags &STMMAC_FLAG_MULTI_MSI_EN ); + priv->plat->dma_cfg->perch_irq_en = + (priv->plat->flags &STMMAC_FLAG_PERCH_IRQ_EN ); priv->dev->irq = res->irq; priv->wol_irq = res->wol_irq;include/linux/stmmac.h +2
-2@@ -98,7 +98,7 @@ struct stmmac_dma_cfg {int mixed_burst;bool aal;bool eame; -bool multi_msi_en; +bool perch_irq_en;bool dche; };@@ -213,7 +213,7 @@ struct dwmac4_addrs {#define STMMAC_FLAG_TSO_EN BIT(4)#define STMMAC_FLAG_SERDES_UP_AFTER_PHY_LINKUP BIT(5)#define STMMAC_FLAG_VLAN_FAIL_Q_EN BIT(6) -#define STMMAC_FLAG_MULTI_MSI_EN BIT(7) +#define STMMAC_FLAG_PERCH_IRQ_EN BIT(7)#define STMMAC_FLAG_EXT_SNAPSHOT_EN BIT(8)#define STMMAC_FLAG_INT_SNAPSHOT_EN BIT(9)#define STMMAC_FLAG_RX_CLK_RUNS_IN_LPI BIT(10)Signature · 1 line
2.40.1
PATCH v5 5/9 net: stmmac: xgmac: support per-channel irq
In reply to Jisheng ZhangThe IP supports per channel interrupt, add support for this usage case.
--- .../net/ethernet/stmicro/stmmac/dwxgmac2.h | 2 ++ .../ethernet/stmicro/stmmac/dwxgmac2_dma.c | 33 +++++++++++-------- 2 files changed, 22 insertions(+), 13 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h +2 -0
@@ -340,6 +340,8 @@/* DMA Registers */ #define XGMAC_DMA_MODE 0x00003000 +#define XGMAC_INTM GENMASK(13, 12) +#define XGMAC_INTM_MODE1 0x1#define XGMAC_SWR BIT(0)#define XGMAC_DMA_SYSBUS_MODE 0x00003004#define XGMAC_WR_OSR_LMT GENMASK(29, 24)
drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +20 -13
@@ -31,6 +31,13 @@ static void dwxgmac2_dma_init(void __iomem *ioaddr, value |=XGMAC_EAME ;writel (value, ioaddr +XGMAC_DMA_SYSBUS_MODE ); + +if (dma_cfg->perch_irq_en) { + value =readl (ioaddr +XGMAC_DMA_MODE ); + value &= ~XGMAC_INTM ; + value |=FIELD_PREP (XGMAC_INTM ,XGMAC_INTM_MODE1 ); +writel (value, ioaddr +XGMAC_DMA_MODE ); + } } static void dwxgmac2_dma_init_chan(struct stmmac_priv *priv,
@@ -365,20 +372,20 @@ static int dwxgmac2_dma_interrupt(struct stmmac_priv *priv, }/* TX/RX NORMAL interrupts */ -if (likely (intr_status &XGMAC_NIS )) { -if (likely (intr_status &XGMAC_RI )) { -u64_stats_update_begin (&rx_q->rxq_stats.syncp); - rx_q->rxq_stats.rx_normal_irq_n++; -u64_stats_update_end (&rx_q->rxq_stats.syncp); - ret |= handle_rx; - } -if (likely (intr_status & (XGMAC_TI |XGMAC_TBU ))) { -u64_stats_update_begin (&tx_q->txq_stats.syncp); - tx_q->txq_stats.tx_normal_irq_n++; -u64_stats_update_end (&tx_q->txq_stats.syncp); - ret |= handle_tx; - } +if (likely (intr_status &XGMAC_RI )) { +u64_stats_update_begin (&rx_q->rxq_stats.syncp); + rx_q->rxq_stats.rx_normal_irq_n++; +u64_stats_update_end (&rx_q->rxq_stats.syncp); + ret |= handle_rx; + } +if (likely (intr_status &XGMAC_TI )) { +u64_stats_update_begin (&tx_q->txq_stats.syncp); + tx_q->txq_stats.tx_normal_irq_n++; +u64_stats_update_end (&tx_q->txq_stats.syncp); + ret |= handle_tx; } +if (unlikely (intr_status &XGMAC_TBU )) + ret |= handle_tx;/* Clear interrupts */ writel (intr_en & intr_status, ioaddr +XGMAC_DMA_CH_STATUS (chan));
Signature · 1 line
2.40.1
Re: [PATCH net-next v5 5/9] net: stmmac: xgmac: support per-channel irq
Quoted 61 lines · Jisheng Zhang
The IP supports per channel interrupt, add support for this usage case.
Signed-off-by Jisheng Zhang <[email protected]>--- .../net/ethernet/stmicro/stmmac/dwxgmac2.h | 2 ++ .../ethernet/stmicro/stmmac/dwxgmac2_dma.c | 33 +++++++++++-------- 2 files changed, 22 insertions(+), 13 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h +2
-0@@ -340,6 +340,8 @@/* DMA Registers */ #define XGMAC_DMA_MODE 0x00003000 +#define XGMAC_INTM GENMASK(13, 12) +#define XGMAC_INTM_MODE1 0x1#define XGMAC_SWR BIT(0)#define XGMAC_DMA_SYSBUS_MODE 0x00003004#define XGMAC_WR_OSR_LMT GENMASK(29, 24)drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +11
-13@@ -31,6 +31,13 @@ static void dwxgmac2_dma_init(void __iomem *ioaddr, value |=XGMAC_EAME ;writel (value, ioaddr +XGMAC_DMA_SYSBUS_MODE ); + +if (dma_cfg->perch_irq_en) { + value =readl (ioaddr +XGMAC_DMA_MODE ); + value &= ~XGMAC_INTM ; + value |=FIELD_PREP (XGMAC_INTM ,XGMAC_INTM_MODE1 ); +writel (value, ioaddr +XGMAC_DMA_MODE ); + } } static void dwxgmac2_dma_init_chan(struct stmmac_priv *priv,@@ -365,20 +372,20 @@ static int dwxgmac2_dma_interrupt(struct stmmac_priv *priv, }/* TX/RX NORMAL interrupts */ -if (likely (intr_status &XGMAC_NIS )) { -if (likely (intr_status &XGMAC_RI )) { -u64_stats_update_begin (&rx_q->rxq_stats.syncp); - rx_q->rxq_stats.rx_normal_irq_n++; -u64_stats_update_end (&rx_q->rxq_stats.syncp); - ret |= handle_rx; - } -if (likely (intr_status & (XGMAC_TI |XGMAC_TBU ))) { -u64_stats_update_begin (&tx_q->txq_stats.syncp); - tx_q->txq_stats.tx_normal_irq_n++; -u64_stats_update_end (&tx_q->txq_stats.syncp); - ret |= handle_tx; - } +if (likely (intr_status &XGMAC_RI )) { +u64_stats_update_begin (&rx_q->rxq_stats.syncp); + rx_q->rxq_stats.rx_normal_irq_n++; +u64_stats_update_end (&rx_q->rxq_stats.syncp);
drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c static int dwxgmac2_dma_interrupt(struct stmmac_priv *priv, · line 389
Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +9
-0+ ret |= handle_rx; + } +if (likely (intr_status &XGMAC_TI )) { +u64_stats_update_begin (&tx_q->txq_stats.syncp); + tx_q->txq_stats.tx_normal_irq_n++; +u64_stats_update_end (&tx_q->txq_stats.syncp); + ret |= handle_tx; } +if (unlikely (intr_status &XGMAC_TBU )) + ret |= handle_tx;
Just curious. Is this change really necessary seeing NIS IRQ is unmasked and it is unmasked-OR of the RI/TI/TBU flags in the DMA_CHx_Status register? Moreover based on the HW manual, DMA_CHx_Status reflects raw IRQ flags status except NIS and AIS which are the masked OR of the respective flags. So AFAIU NIS will be set in anyway if you have RI/TI/TBU IRQs enabled.
-Serge(y)
Quoted 7 lines
drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c +0
-0/* Clear interrupts */ writel (intr_en & intr_status, ioaddr +XGMAC_DMA_CH_STATUS (chan));Signature · 1 line
2.40.1
PATCH v5 6/9 dt-bindings: net: snps,dwmac: add safety irq support
In reply to Jisheng ZhangThe snps dwmac IP support safety features, and those Safety Feature Correctible Error and Uncorrectible Error irqs may be separate irqs.
--- .../devicetree/bindings/net/snps,dwmac.yaml | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/net/snps,dwmac.yaml +11 -2
@@ -103,17 +103,26 @@ properties: interrupts: minItems: 1 + maxItems: 5 + additionalItems: true items: - description: Combined signal for various interrupt events - description: The interrupt to manage the remote wake-up packet detection - description: The interrupt that occurs when Rx exits the LPI state + - description: The interrupt that occurs when Safety Feature Correctible Errors happen + - description: The interrupt that occurs when Safety Feature Uncorrectible Errors happen interrupt-names: minItems: 1 + maxItems: 5 + additionalItems: true items: - const: macirq - - enum: [eth_wake_irq, eth_lpi] - - const: eth_lpi + - enum: + - eth_wake_irq + - eth_lpi + - sfty_ce + - sfty_ue clocks: minItems: 1
Signature · 1 line
2.40.1
Re: [PATCH net-next v5 6/9] dt-bindings: net: snps,dwmac: add safety irq support
Quoted 28 lines · Jisheng Zhang
The snps dwmac IP support safety features, and those Safety Feature Correctible Error and Uncorrectible Error irqs may be separate irqs.
Signed-off-by Jisheng Zhang <[email protected]>--- .../devicetree/bindings/net/snps,dwmac.yaml | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-)Documentation/devicetree/bindings/net/snps,dwmac.yaml +5
-0@@ -103,17 +103,26 @@ properties: interrupts: minItems: 1 + maxItems: 5 + additionalItems: true items: - description: Combined signal for various interrupt events - description: The interrupt to manage the remote wake-up packet detection - description: The interrupt that occurs when Rx exits the LPI state + - description: The interrupt that occurs when Safety Feature Correctible Errors happen + - description: The interrupt that occurs when Safety Feature Uncorrectible Errors happen interrupt-names: minItems: 1 + maxItems: 5
Documentation/devicetree/bindings/net/snps,dwmac.yaml properties: · line 125
Quoted 10 lines
Documentation/devicetree/bindings/net/snps,dwmac.yaml +6
-2+ additionalItems: true items: - const: macirq - - enum: [eth_wake_irq, eth_lpi] - - const: eth_lpi + - enum: + - eth_wake_irq + - eth_lpi + - sfty_ce + - sfty_ue
IIUC this would mean the next constraints:
Item 0: must be macirq,
Item 1: any of eth_wake_irq, eth_lpi, sfty_ce, sfty_ue
Items 2:4: any bla-bla-bla.
After adding the per-DMA-channel IRQs in the next patches the array will be extended to up to 37 any names. It doesn't look correct. What about converting it to the position independent arrays constraint:
interrupts:
minItems: 1
maxItems: 34
interrupt-names:
minItems: 1
maxItems: 34
items:
oneOf:
- description: Combined signal for various interrupt events
const: macirq
- description: The interrupt to manage the remote wake-up packet detection
const: eth_wake_irq
- description: The interrupt that occurs when Rx exits the LPI state
const: eth_lpi
- description: Safety Feature Correctible Errors interrupt
const: sfty_ce
- description: Safety Feature Uncorrectible Errors interrupt
const: sfty_ue
- description: DMA Tx per-channel interrupt
pattern: '^dma_tx([0-9]|1[0-5])?$'
- description: DMA Rx per-channel interrupt
pattern: '^dma_rx([0-9]|1[0-1])?$'
allOf:
- contains:
const: macirq
Hope neither Krzysztof nor Rob will be against such modification especially seeing it's the only way to resolve the very much possible case of a device having macirq and per-DMA-channel IRQs but lacking the LPI, PMT or Safety IRQs.
Note 1. I've changed the name of the Tx/Rx IRQs to having the "dma_" suffix to signify that these are actually DMA-channel IRQs. The MTL queue interrupts drive the sbd_intr_o signal which is tracked by the "macirq" line.
Note 2. I've reduced the number of DMA Rx IRQs to being up to 12 in accordance with available to me DW XGMAC HW manual.
-Serge(y)
Quoted 7 lines
Documentation/devicetree/bindings/net/snps,dwmac.yaml +0
-0clocks: minItems: 1Signature · 1 line
2.40.1
Rob Herring
maintainerRe: [PATCH net-next v5 6/9] dt-bindings: net: snps,dwmac: add safety irq support
Quoted 36 lines · Serge Semin
Quoted 35 lines · Jisheng Zhang
The snps dwmac IP support safety features, and those Safety Feature Correctible Error and Uncorrectible Error irqs may be separate irqs.
Signed-off-by Jisheng Zhang <[email protected]>--- .../devicetree/bindings/net/snps,dwmac.yaml | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-)Documentation/devicetree/bindings/net/snps,dwmac.yaml +8
-2@@ -103,17 +103,26 @@ properties: interrupts: minItems: 1 + maxItems: 5 + additionalItems: true items: - description: Combined signal for various interrupt events - description: The interrupt to manage the remote wake-up packet detection - description: The interrupt that occurs when Rx exits the LPI state + - description: The interrupt that occurs when Safety Feature Correctible Errors happen + - description: The interrupt that occurs when Safety Feature Uncorrectible Errors happen interrupt-names: minItems: 1 + maxItems: 5 + additionalItems: true items: - const: macirq - - enum: [eth_wake_irq, eth_lpi] - - const: eth_lpi + - enum: + - eth_wake_irq
Quoted 8 lines
Documentation/devicetree/bindings/net/snps,dwmac.yaml properties: · line 125
Quoted 3 lines
Documentation/devicetree/bindings/net/snps,dwmac.yaml +3
-0+ - eth_lpi + - sfty_ce + - sfty_ueIIUC this would mean the next constraints:
Item 0: must be macirq,
Item 1: any ofeth_wake_irq,eth_lpi,sfty_ce,sfty_ue
Items 2:4: any bla-bla-bla.
Indeed.
Quoted 30 lines
After adding the per-DMA-channel IRQs in the next patches the array will be extended to up to 37 any names. It doesn't look correct. What about converting it to the position independent arrays constraint:
interrupts:
minItems: 1
maxItems: 34interrupt-names:
minItems: 1
maxItems: 34
items:
oneOf:
- description: Combined signal for various interrupt events
const: macirq
- description: The interrupt to manage the remote wake-up packet detection
const:eth_wake_irq
- description: The interrupt that occurs when Rx exits the LPI state
const:eth_lpi
- description: Safety Feature Correctible Errors interrupt
const:sfty_ce
- description: Safety Feature Uncorrectible Errors interrupt
const:sfty_ue
- description: DMA Tx per-channel interrupt
pattern: '^dma_tx([0-9]|1[0-5])?$'
- description: DMA Rx per-channel interrupt
pattern: '^dma_rx([0-9]|1[0-1])?$'
Quoted 3 lines
allOf:
- contains:
const: macirq
This would keep macirq being first:
allOf:
- maxItems: 34
items:
- const: macirq
In newer json-schema the schema and list versions were split into "prefixItems" and "items", so we could avoid the "allOf" with that. Unfortunately, the former is the list version which we use everywhere. I don't really want to do a treewide change of that and also I find the 'prefixItems' name kind of awkward.
Quoted 4 lines
Hope neither Krzysztof nor Rob will be against such modification especially seeing it's the only way to resolve the very much possible case of a device having macirq and per-DMA-channel IRQs but lacking the LPI, PMT or Safety IRQs.
Don't love it, but I give up on these licensed IPs. :(
Rob
PATCH v5 7/9 net: stmmac: platform: support parsing safety irqs from DT
In reply to Jisheng ZhangThe snps dwmac IP may support safety features, and those Safety Feature Correctible Error and Uncorrectible Error irqs may be separate irqs. Add support to parse the safety irqs from DT.
--- .../net/ethernet/stmicro/stmmac/stmmac_platform.c | 12 ++++++++++++ 1 file changed, 12 insertions(+)
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +12 -0
@@ -737,6 +737,18 @@ int stmmac_get_platform_resources(struct platform_device *pdev,dev_info (&pdev->dev,"IRQ eth_lpi not found\n" ); } + stmmac_res->sfty_ce_irq =platform_get_irq_byname_optional (pdev,"sfty_ce" ); +if (stmmac_res->sfty_ce_irq <0 ) { +if (stmmac_res->sfty_ce_irq == -EPROBE_DEFER ) +return -EPROBE_DEFER ; + } + + stmmac_res->sfty_ue_irq =platform_get_irq_byname_optional (pdev,"sfty_ue" ); +if (stmmac_res->sfty_ue_irq <0 ) { +if (stmmac_res->sfty_ue_irq == -EPROBE_DEFER ) +return -EPROBE_DEFER ; + } + stmmac_res->addr =devm_platform_ioremap_resource (pdev,0 );return PTR_ERR_OR_ZERO (stmmac_res->addr);
Signature · 1 line
2.40.1
PATCH v5 8/9 dt-bindings: net: snps,dwmac: add per channel irq support
In reply to Jisheng ZhangThe IP supports optional per channel interrupt, add support for this usage case.
--- .../devicetree/bindings/net/snps,dwmac.yaml | 68 ++++++++++++++++++- 1 file changed, 66 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/net/snps,dwmac.yaml +66 -2
@@ -103,7 +103,7 @@ properties: interrupts: minItems: 1 - maxItems: 5 + maxItems: 37 additionalItems: true items: - description: Combined signal for various interrupt events
@@ -111,10 +111,42 @@ properties: - description: The interrupt that occurs when Rx exits the LPI state - description: The interrupt that occurs when Safety Feature Correctible Errors happen - description: The interrupt that occurs when Safety Feature Uncorrectible Errors happen + - description: rx0 per-channel interrupt + - description: rx1 per-channel interrupt + - description: rx2 per-channel interrupt + - description: rx3 per-channel interrupt + - description: rx4 per-channel interrupt + - description: rx5 per-channel interrupt + - description: rx6 per-channel interrupt + - description: rx7 per-channel interrupt + - description: rx8 per-channel interrupt + - description: rx9 per-channel interrupt + - description: rx10 per-channel interrupt + - description: rx11 per-channel interrupt + - description: rx12 per-channel interrupt + - description: rx13 per-channel interrupt + - description: rx14 per-channel interrupt + - description: rx15 per-channel interrupt + - description: tx0 per-channel interrupt + - description: tx1 per-channel interrupt + - description: tx2 per-channel interrupt + - description: tx3 per-channel interrupt + - description: tx4 per-channel interrupt + - description: tx5 per-channel interrupt + - description: tx6 per-channel interrupt + - description: tx7 per-channel interrupt + - description: tx8 per-channel interrupt + - description: tx9 per-channel interrupt + - description: tx10 per-channel interrupt + - description: tx11 per-channel interrupt + - description: tx12 per-channel interrupt + - description: tx13 per-channel interrupt + - description: tx14 per-channel interrupt + - description: tx15 per-channel interrupt interrupt-names: minItems: 1 - maxItems: 5 + maxItems: 37 additionalItems: true items: - const: macirq
@@ -123,6 +155,38 @@ properties: - eth_lpi - sfty_ce - sfty_ue + - rx0 + - rx1 + - rx2 + - rx3 + - rx4 + - rx5 + - rx6 + - rx7 + - rx8 + - rx9 + - rx10 + - rx11 + - rx12 + - rx13 + - rx14 + - rx15 + - tx0 + - tx1 + - tx2 + - tx3 + - tx4 + - tx5 + - tx6 + - tx7 + - tx8 + - tx9 + - tx10 + - tx11 + - tx12 + - tx13 + - tx14 + - tx15 clocks: minItems: 1
Signature · 1 line
2.40.1
PATCH v5 9/9 net: stmmac: platform: support parsing per channel irq from DT
In reply to Jisheng ZhangThe snps dwmac IP may support per channel interrupt. Add support to parse the per channel irq from DT.
--- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 10 ++++---- .../ethernet/stmicro/stmmac/stmmac_platform.c | 23 +++++++++++++++++++ 2 files changed, 29 insertions(+), 4 deletions(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +6 -4
@@ -3619,7 +3619,7 @@ static int stmmac_request_irq_multi_channel(struct net_device *dev)for (i =0 ; i < priv->plat->rx_queues_to_use; i++) {if (i >=MTL_MAX_RX_QUEUES )break ; -if (priv->rx_irq[i] ==0 ) +if (priv->rx_irq[i] <=0 )continue ; int_name = priv->int_name_rx_irq[i];
@@ -3644,7 +3644,7 @@ static int stmmac_request_irq_multi_channel(struct net_device *dev)for (i =0 ; i < priv->plat->tx_queues_to_use; i++) {if (i >=MTL_MAX_TX_QUEUES )break ; -if (priv->tx_irq[i] ==0 ) +if (priv->tx_irq[i] <=0 )continue ; int_name = priv->int_name_tx_irq[i];
@@ -7300,8 +7300,10 @@ int stmmac_dvr_probe(struct device *device, priv->plat = plat_dat; priv->ioaddr = res->addr; priv->dev->base_addr = (unsigned long )res->addr; - priv->plat->dma_cfg->perch_irq_en = - (priv->plat->flags &STMMAC_FLAG_PERCH_IRQ_EN ); +if (res->rx_irq[0 ] >0 && res->tx_irq[0 ] >0 ) { + priv->plat->flags |=STMMAC_FLAG_PERCH_IRQ_EN ; + priv->plat->dma_cfg->perch_irq_en = true; + } priv->dev->irq = res->irq; priv->wol_irq = res->wol_irq;
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +23 -0
@@ -704,6 +704,9 @@ EXPORT_SYMBOL_GPL(stmmac_remove_config_dt);int stmmac_get_platform_resources (struct platform_device *pdev,struct stmmac_resources *stmmac_res) { +char irq_name[8 ]; +int i; +memset (stmmac_res,0 ,sizeof (*stmmac_res));/* Get IRQ information early to have an ability to ask for deferred
@@ -737,6 +740,26 @@ int stmmac_get_platform_resources(struct platform_device *pdev,dev_info (&pdev->dev,"IRQ eth_lpi not found\n" ); } +for (i =0 ; i <MTL_MAX_RX_QUEUES ; i++) { +snprintf (irq_name,sizeof (irq_name),"rx%i" , i); + stmmac_res->rx_irq[i] =platform_get_irq_byname_optional (pdev, irq_name); +if (stmmac_res->rx_irq[i] <0 ) { +if (stmmac_res->rx_irq[i] == -EPROBE_DEFER ) +return -EPROBE_DEFER ; +break ; + } + } + +for (i =0 ; i <MTL_MAX_TX_QUEUES ; i++) { +snprintf (irq_name,sizeof (irq_name),"tx%i" , i); + stmmac_res->tx_irq[i] =platform_get_irq_byname_optional (pdev, irq_name); +if (stmmac_res->tx_irq[i] <0 ) { +if (stmmac_res->tx_irq[i] == -EPROBE_DEFER ) +return -EPROBE_DEFER ; +break ; + } + } + stmmac_res->sfty_ce_irq =platform_get_irq_byname_optional (pdev,"sfty_ce" );if (stmmac_res->sfty_ce_irq <0 ) {if (stmmac_res->sfty_ce_irq == -EPROBE_DEFER )
Signature · 1 line
2.40.1